Operation 8030C
MENU
PROGRAM
RES ET
Calibration
NOTE: Your thermostat comes from the factory calibrated to + or - 1oF actual
temperature. It is an accurate instrument. If you want your thermostat to display
the same temperature as another thermometer in your home, you can adjust its
calibration.
To change the calibration:
The unit must be in the HEAT or COOL mode.
Press the MENU button.
Press the Temp Up/Temp Down arrows to adjust the temperaturereading.
CALIBRATE DISPLAY ONwill appear.
Press HOME to save the new setting.
MENU
PR
O
G
R M
A
-T FACTOR
R
E
S
E
T
CALIBRATE DISPLAY
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
401-011
MENU screen
Displayed when the MENU button is pressed from the HOME screen.
3
Set
oC -oF
Lock Program
Touch for 5 sec
to lock or unlock
Return
HOME
1 Set Day
Touch this area to set
the day of the week.
Touch this to
set temperature
display.
2
Set Time
Touch this area to set
the time of day.
Left arrow goes back,
right arrow goes forward.
-T FACTOR
Temperature Swing
set
CALIBRATE DISPLAY
Filter Timer set
Calibration indicator
This comes on if you
have altered the
Calibration
Use this to calibrate your LCD
display to match another
Chirp set
Touch this to turn the
audible chirp on or off.
calibration of your unit
thermometer.
PG 3
PROGRAM screen
Displayed when the PROGRAM button is pressed from the HOME
Return HOME
Set Time Slot
Touch this area to set
the Time Slot you
Set Program Day
Touch this area to set
the day of the week you
want to program Target
Temps for.
When programming
is complete touch this
to run your program.
want to program.
Set Program Time
Touch this area to set the
time of day you want each
time period to start.
Left arrow goes back,
right arrow goes forward.
Copy
Touch this area to copy
current program to the
Review
Temp Up / Temp Down
arrows. Touch these to
raise and lower
next day
touch this area to auto cycle
through your program
Download from Www.Somanuals.com. All Manuals Search AendaDcohwnTloaadrg. et Temp.
PG 4
1 Configure
Press MENU to configure the thermostat (from HOME screen).
Set day of the week -
Touch the Day of the week area to cycle through
the days of the week to select the current day.
Set time of day -
Touch the Time of Day arrows to move the time
selection forward or backward until it displays the
current time. Touch and hold for faster setting.
Backward Forward
Set oC -oF display
Touch the F and it will toggle to oC.
o
Set audible chirp -
Touch the the musical note icon to select the chirp
or no chirp.
Return HOME by touching the home icon.
PG 5
2 Auto-run
This Thermostat comes preprogrammed with an Energy-
StarTM approved program. This program is recommended by
the EPA for energy efficiency.
We strongly recommend that you Auto-Run this program for one week, and
see if it works for you. If it does not fit your needs you can always input a
custom program.
To Auto-Run the Energy-Star program, select HEAT or COOL with the
TM
mode switch. The unit is now running the Energy-StarTM program.
The clock is displayed on the left. The ambient temperature is displayed in
the the center of the LCD touch screen. The TIME SLOT icon indicates the
TIME SLOT active in the Energy-StarTm program.
The programmed temperature is shown on the lower right. For program
details refer to the Energy-StarTM program chart below.
EVEN
6:00pm 10:00pm
85 78
NITE
EVEN
6:00pm 10:00pm
NITE
DAY
8:00am
DAY
8:00am
MORN
6:00am
MORN
6:00am
COOL
HEAT
All Days
78
o
F
oF
oF
All Days
70
o
F
62
o
F
70
o
F
62
o
F
Download from Www.Somanuals.com. All Manuals Search And Download.
PG 6
3 Program
NOTE: 60 Second Rule-During programming, if a button is not pushed in
60 seconds, the unit will return to the home screen. Everything you have
changed while programming will automatically be saved.
Press PROGRAM to go to the programming screen.
Select HEAT with the HEAT/Cool MODE
switch.
Select the day you want to program-
Touch the Day of the week area to cycle through
the days of the week to select the desired day.
Select the time slot you want to program -
Touch the Time slot area to cycle through the 4
time slots, until it displays the desired time slot.
Select the time of day -
Touch the Time of Day arrows to move the time
selection forward or backward until it displays the
Backward Forward
PG 7
desired time.
3 Program cont.
Select the desired temperature -
Touch the UP temp / Down temp arrows.
Repeat the above procedures for each day of the week and
each time slot of the day as desired.
To REVIEW your program touch REVIEW. Each time slot for each day
or set of identical days, will be displayed every 3 seconds.
Return HOME by touching the home icon.
To COPY the program from the current day to another day -
Touch COPY on the program screen. The current day will remain solid,
the destination day will flash.
Touch the day area to advance the day and select a copy destination.
Touch COPY again to copy all settings to the destination day.
To program for cooling -
Select COOL with the Heat/Cool MODE switch and repeat the above
procedure.Download from Www.Somanuals.com. All Manuals Search And Download.
PG 8
Manual
The 8030C has 3 manual override commands. These are accessed by
touching the Current Temp Display at the HOME screen (center of screen).
Target Temperature
Return HOME
HOLD
Touch this area to set
a comfortable target
temp for the system
to hold until you return
and remove HOLD.
TEMPORARY
Manual Override indicator
Shows you have temporarily
modified the Target Temp.
Temp Up / Temp Downarrows
Touch these to raise and lower
the manual override Target Temp.
PG 9
MANUAL Temporary Override screen
Manual cont.
TEMPORARY Overide -
At the Manual override screen, Touch theTemp Up / Temp Down
arrows to select your desired temporary Target Temperature.
Touch HOME to return to operation.
The TEMPORARY icon will go on indicating you have modified the
Target Temp for the current Time Slot only(see PG7-Time Slot).
HOLD -
At the Manual override screen, Touch HOLD to initiate a hold
temperature.
Touch the Temp Up / Temp Downarrows to select your hold
temperature.
Touch HOME to return to operation.
The HOLD ON icon will flash indicating you have changed the
Target Temp.
The system will HOLD this temperature until you return to this screen
and de-select HOLD, by touching the HOLD icon again.
The Mode Switch must be in
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAT or COOL mode to override.
PG 10
4 Special Features
Swing
Swing setting determines the temperature difference from
ON to OFF that the thermostat will command the HVAC system to run.
With the MODE switch in HEAT or COOL, press the MENU button.
Touch the SWING icon and the current setting of temp
swing is shown on the display (default at 3 ).
To change the swing, touch the left or right arrows.
The furnace will cycle more at the lower numbers as it
tries to keep your set point constant.
Filter
The 8030C has a feature that keeps track of actual furnace run time and
reminds you to periodically replace your system's air filter.
Press MENU (from HOME screen) and touch FILTER icon.
This will display your accumulated filter run time.
To input a new filter life time, touch the FILTER icon for 3 seconds.
Input the lifetime hours for your new filter.
To zero the filter timer for a new filter, touch the
accumulated time display.
To leave the filter display, touchHOME
PG 11
4 Spec. Featr. cont.
Lock
Allows you to to prevent any changes in custom settings.
To lock, touch the LOCK icon on the MENU screen for 5 sec.
To unlock, Touch the locked icon for 5 sec.
Low Battery
When the batteries are low, the battery icon will come on and flash.
The two AA Batteries in the unit need to be replaced. In some installations
your heater system will stop functioning when the thermostat loses power.
Replace batteries as soon as you see this warning. The thermostat
programs will remain for 30 seconds while the batteries are changed.
Do not take longer than 30 sec to change the batteries in your unit or
you will lose all custom settings and all programming. Only the Energy-
StarTM program will remain. Once the batteries are replaced, the system will
return to normal in 2 seconds.
12/24 hour
The thermostat can display time in 12 or 24 hour formats. At the
HOME screen touch the time display to toggle from 12 to 24 hr display.
Download from Www.Somanuals.com. All Manuals Search And Download.
PG 12
|