OWNERS MANUAL
Serial No.
99300642-b 1/06
EDR10611
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Advisory ............................................................................................................... 4
Acoustics.............................................................................................................. 6
Installation ............................................................................................................ 7
Sleep Number® Mattress Installation ............................................................... 13
Hand Control Operation .................................................................................... 16
Receiver Unit Operation.................................................................................... 17
Programming ..................................................................................................... 18
Accessories........................................................................................................ 23
Troubleshooting................................................................................................. 24
1-2-20 Warranty ................................................................................................. 25
© Leggett & Platt, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
This Precision Comfort™ adjustable foundation has been quality engineered with design
features to assure comfort and safety when operated properly.
ELECTRICAL GROUNDING
PRODUCT RATINGS
This product is equipped with a polarized,
grounded electrical power cord. The
power cord will only fit into a grounded,
electrical surge protection device (not
included) or a grounded electrical outlet.
The bed lift motors are not designed for
continuous use. Reliable operation and full
life expectancy will be realized as long as
the lift motors do not operate any more
than five (5) minutes over a thirty (30)
minute period, or approximately 15% duty
cycle. Note: massage equipped beds are
not designed for continuous, extended
massage operation. Massage systems are
rated for a maximum of 2 hours of use
within any 6 hour period. Any attempt to
circumvent or exceed product ratings will
shorten the life expectancy of the product
and may void the warranty.
FOR OPTIMUM ADJUSTABLE BED
OPERATION, USE A GROUNDED,
ELECTRICAL SURGE PROTECTION
DEVICE (NOT INCLUDED). FAILURE TO
USE A SURGE PROTECTION DEVICE
COULD COMPROMISE SAFETY OR
CAUSE PRODUCT MALFUNCTION.
The recommended weight restrictions for
Precision Comfort™ adjustable
WARRANTY WARNING
Do not open any control boxes, motors or
hand control devices (with the exception
of the hand control and power down box
battery compartments). The product
warranty will be void if these components
are tampered with. Do not attempt to alter
component wiring or adjust or modify the
structure of the product in any way or the
warranty will be void. Any repair or
replacement of adjustable bed parts must
be performed by authorized personnel.
foundations are as follows: Twin-300 lbs
(136.07kg), Full-375 lbs (170.09kg) and
Queen-425 lbs (192.77kg). The bed will
structurally support the recommended
weights distributed evenly across the
head and foot sections. This product is not
designed to support or lift this amount
only in the head or foot sections alone.
Note: Exceeding the recommended
weight restrictions could damage your
adjustable bed and void your warranty.
For best performance, consumers should
enter and exit the adjustable bed with the
bed in the flat (horizontal) position. DO
NOT SIT ON THE HEAD OR FOOT SECTIONS
WHILE IN THE RAISED POSITION.
LUBRICATION
This product is designed to be
maintenance free. The lift motors are
permanently lubricated and sealed—no
additional lubrication is required. Do not
apply lubricant to lift motor lead screws or
any nylon nuts or the bed may
inadvertently creep downward from the
elevated position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
This Precision Comfort™ adjustable foundation has been quality engineered with design
features to assure comfort and safety when operated properly.
SMALL CHILDREN / PETS WARNING
After the foundation is unboxed,
FCC COMPLIANCE
Precision Comfort™ electrical components
are rated for 110/120 voltage, 60Hz, 3.9
amp. Components meet Class B digital
device rating (Part 15, FCC rules) for
residential use. Precision Comfort™
adjustable foundations generate, use and
may radiate radio frequency energy. Radio
communication may be affected if not
installed and operated as recommended
in this manual.
immediately dispose of packaging
material as it can smother small children
and pets. To avoid injury, children or pets
should not be allowed to play under or on
the bed. Children should not operate this
bed without adult supervision.
HOSPITAL USE DISCLAIMER
This foundation is designed for in-home
use only. It is not approved for hospital
use and does not comply with hospital
standards. Do not use this bed with tent
type oxygen therapy equipment, or use
near explosive gases.
LOCKING CASTER SAFETY FEATURE
(If applicable)
The Precision Comfort™ foundation is
equipped with locking casters to prohibit
the bed from movement. For best results,
place rubber caster cups under locking
casters when the bed is located on
smooth or hard surface flooring—it is
possible for locking caster equipped beds
to slide without the use of rubber caster
cups.
PACEMAKER WARNING
This product produces a vibrating
sensation. It is possible that individuals
with heart-assist pacemakers may
experience a sensation similar to exercise.
Consult physician for complete
information.
To activate locking casters, push down on
the lock tab. To disengage the locking
mechanism, lift up the lock tab (see
illustration below).
SERVICE REQUIREMENTS
Service technicians are not responsible for
moving furniture, removing headboards
and footboards or any items required to
perform maintenance on your adjustable
foundation. In the event the technician is
unable to perform service due to lack of
accessibility, the service call will be billed
to the purchaser and the service will have
to be rescheduled.
LOCKING CASTER
DETAIL
OCK
L
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ACOUSTICS
LIFTING/LOWERING MECHANISMS
LOCATION ENVIRONMENT
The lift/lower feature will emit a minimal
humming sound during operation. This is
normal.
The level of sound experienced during
Precision Comfort™ operation is directly
related to the location environment. For
example, when a bed is located on a
hardwood floor with the massage feature
in operation, a vibrating tone will be
audible. To minimize this resonance, place
a piece of carpet—or optional rubber
caster cups—under each leg or caster of
the bed. See the accessory sheet included
with this product for rubber caster cup
order information.
During Precision Comfort™ operation, the
lift arm wheels make contact with the
platform support of the bed. This applies
slight tension on the moving components
and resonance is reduced to a minimum
level. If excessive noise or vibration is
experienced, reverse the movement
action (up or down) of the bed with the
hand control. This should realign the bed’s
activating mechanisms to the proper
operational position.
It is possible to experience vibration or
noise from the headboard brackets,
headboards or footboards if mounting
bolts are not firmly tightened.
MASSAGE OPERATION
The massage feature will emit a minimal
tone during operation. This is normal.
When the massage level is increased,
motor resonance will intensify
accordingly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
For Precision Comfort™ installation and setup, complete the numbered procedure
indicated below and on the following pages:
1. Before discarding any packing materials,
check the adjustable bed shipping carton
and verify the following items are
included:
• (1) Mattress Retainer
MATTRESS
RETAINER
• (1) Mattress Retainer Hardware Kit
• (4) Bed Legs
• (4) Locking Leg Casters
• (2) Headboard Bracket Assemblies
• (1) Headboard Bracket Hardware Kit
• (1) Precision Comfort® Foundation
Hardware Kit (not shown)
MATTRESS RETAINER
HARDWARE KIT
• (1) Hand Control
(hardware: 16 pieces)
• (1) Owners Manual
• (1) Registration Card
LEG (4 pieces)
ANGLE BRACE
LOCKING LEG CASTER
(4 pieces)
HAND CONTROL
HEADBOARD BRACKET ASSEMBLIES
Queen size shown—twin size (or smaller)
headboard brackets are not
equipped with angle brace.
HEADBOARD BRACKET
HARDWARE KIT
(hardware: 16 pieces)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
2. Carefully Lift the bed base frame from the
PRESS IN (SLIGHTLY) AND
PUSH DOWN TO REMOVE
BATTERY COMPARTMENT
DOOR
shipping carton, keeping the unit top-side-
down.
3. Install (4) legs into the base frame. Simply
screw each leg into a tapped hole at each
corner of the base frame (FIGURE 1). Insert
casters into the bottom of each bed leg (if
applicable).
POWER DOWN BOX
BATTERY COMPARTMENT DOOR
CASTERS – PRESS-FIT
INTO BOTTOM OF
LEGS (IF APPLICABLE)
FIGURE 2: Receiver unit (power down box) battery
compartment door removal.
LEGS – SCREW INTO
TAPPED HOLE AT
EACH CORNER
BATTERY ORIENTATION IS
INDICATED INSIDE BATTERY
COMPARTMENT
FIGURE 1: Precision Comfort™ leg installation. Caster
installation (if applicable).
DOOR REINSTALLATION:
TABS
PRESS COMPARTMENT DOOR
AGAINST THE BATTERY ENDS,
SLIDE DOOR UP AND IN
TO ENGAGE THE DOOR TABS
4. Remove and extend out power cord from
the protective packaging.
FIGURE 3: Power down box battery installation and battery
compartment door reinstallation.
6. Remove the plastic packaging from the
bed base frame. Carefully rotate the base
frame over to position the bed top-side-up.
POWER CORDS MUST NOT INTERFERE
WITH ANY ADJUSTABLE BED
MECHANISMS.
7. Plug power cord into a working, grounded
electrical outlet. Note: an electrical surge
protection device is recommended (not
included).
5. Install (2) 9 volt batteries into the receiver
unit (FIGURES 2 and 3). The DC receiver
unit is commonly referred to as a power
down box.
8. Install batteries in hand control. Briefly
activate all functions of the bed with the
hand control to verify all features are in
working order. If foundation does not
operate, refer to the Troubleshooting
section of this manual.
9. Return foundation to the level position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
10. Install mattress retainer as follows:
g. Tighten screws to complete mattress
retainer installation (FIGURE 6).
a. Locate (1) mattress retainer and (1)
mattress retainer hardware kit (bag).
b. Install (1) cupped washer, (1) spacer
and (1) flat washer on (4) mattress
retainer bolts (FIGURE 4).
NOTE
DO NOT USE POWER SCREWDRIVER TO
INSTALL MATTRESS RETAINER. DO NOT
OVERTIGHTEN MATTRESS RETAINER
HARDWARE!
B
ASSEMBLE AS
SHOWN BELOW:
D
CUPPED
WASHER
SPACER
A
C
MATTRESS RETAINER HARDWARE
KIT CONTAINS:
(4) MATTRESS RETAINER BOLTS - A
(4) FLAT WASHERS - B
(4) SPACERS - C
FLAT
WASHER
MATTRESS
RETAINER
BOLT
(4) CUPPED WASHERS - D
FIGURE 4: Mattress retainer hardware.
FIGURE 6: Typical mattress retainer installed.
c. Locate (4) threaded lugs in the top side
of the foot section of the foundation
base. The lugs will be marked with
locating pins.
d. Remove the locating pins (pull out).
e. Install the mattress retainer bolts (loosely)
Note: if adjustable foundation is to be set
up without a headboard, install mattress
on the foundation base frame and
installation is complete. If headboard is
to be installed, proceed to step 11.
into the (4) threaded lugs (FIGURE 5).
f. Slide each U-shaped end of the
mattress retainer around the mattress
retainer bolts. Position the retainer
ends between the spacer and the
washer (FIGURE 5).
MATTRESS
RETAINER
(2) THREADED LUGS IN
EACH SIDE OF THE
FOUNDATION FOOT
FLAT WASHERS FIT BETWEEN
THE FOUNDATION BASE FRAME
AND THE MATTRESS RETAINER
SECTION (MARKED WITH
LOCATING PINS)
FIGURE 5: Mattress retainer installation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
11. Install headboard brackets to the
12. Install headboard bracket assemblies per
the following procedure:
foundation base frame. When attaching (2)
twin size units to a king size headboard,
use swing-away hinges (see accessories)
to connect the twin units.
a. Raise the head section of the bed (with
hand control) to gain access to the bed
base frame.
b. Slide one headboard bracket channel
onto one side of the bed base frame.
Using (2) bolts/nuts (FIGURE 8) attach
channel to base frame (FIGURE 9).
Hand tighten bolts/nuts (loosely) to
allow adjustment of the headboard
bracket channels. Repeat procedure to
install the other headboard bracket
channel to the other side.
NOTE
FAILURE TO FOLLOW HEADBOARD
BRACKET INSTALLATION INSTRUCTIONS
MAY CAUSE HEADBOARD BRACKET
INTERFERENCE WITH BASE FOAM DURING
ADJUSTABLE BED OPERATION. BASE
FOAM OR BASE COVER DAMAGE COULD
RESULT.
IN ORDER TO AVOID A PERSON OR PET
BEING CAUGHT IN THE SPACE
REFERENCED BELOW WHILE THE BED IS IN
MOTION, THE BOTTOM OF THE
HEADBOARD CROSS MEMBER MUST BE
POSITIONED SO THAT THERE IS NO MORE
THAN 3 INCHES (76.2mm) BETWEEN THE
HEADBOARD AND THE TOP OF THE
MATTRESS (FIGURE 7). DO NOT EXCEED
3 INCHES (76.2mm). FAILURE TO FOLLOW
THIS INSTRUCTION COULD RESULT IN
SERIOUS PERSONAL INJURY OR DEATH.
A
C
HEADBOARD BRACKET
HARDWARE KIT CONTAINS:
(4) 3 INCH CARRIAGE BOLTS - A
(4) 1 INCH HEX HEAD BOLTS - B
(8) NUTS - C
B
FIGURE 8: Headboard bracket hardware.
.
3 inches MAX
FIGURE 7: headboard cross member location must not
exceed 3 inches (76.2mm) from the top of the mattress.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
USE (2) 3 INCH CARRIAGE BOLTS AND
NUTS TO ATTACH EACH BRACKET
CHANNEL TO THE FRAME EXTENSIONS
ANGLE
BRACE
ANGLE
BRACE
SLIDE HEADBOARD
BRACKET CHANNEL OVER
THE FRAME EXTENSION
USE (2) 1 INCH BOLTS AND
NUTS (TIGHTEN) TO ATTACH
HEADBOARD BRACKET FLANGE
TO EACH BRACKET CHANNEL
FIGURE 9: Headboard bracket channel installation (one each
side of the head section of the bed).
FIGURE 10: Headboard bracket flange installation (attach one
flange to each of the headboard bracket channels).
c. Attach one headboard bracket flange
to one of the bracket channels with (2)
bolts/nuts. (FIGURE 10) Tighten bolts.
Repeat procedure to attach the other
headboard bracket flange.
NOTE
QUEEN SIZE HEADBOARD BRACKET
ASSEMBLIES ARE SHOWN. TWIN SIZE
HEADBOARD BRACKETS (OR SMALLER)
ARE NOT EQUIPPED WITH ANGLE BRACE
(FIGURES 9 and 10).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
d. Slide headboard bracket assemblies (in
or out) to achieve a distance of 1.5
inches (38.1mm) to 2 inches (50.8mm)
between the edge of the foundation
base and headboard bracket flange
assemblies (FIGURE 11).
1.5 to 2 inches
e. Firmly tighten the 3 inch carriage bolts
of both headboard bracket channels.
f. Measure the distance (center-to-
center) between the mounting holes in
the headboard.
g. Measure the center-to-center distance
between the mounting slots of the
CKET
SLIDE BRA
headboard bracket flanges (FIGURE 12).
CHIEVE
A
ASSEMBLIES IN OR
O
OUT T
h. If bracket flange adjustment is required
to accept the headboard, remove the 1
inch headboard bracket flange bolts
and move
POSITION
FIGURE 11: Headboard bracket position from the edge of the
foundation base frame.
flanges side-to-
side for the
adjustment
(FIGURE 12).
Reinstall bolts
and tighten.
REMO
VE 1 INCH BOL
FLANGES T
TS AND REL
O
A
OCA
CHIEVE CENTER-
CENTER DIST
HEADBO
TE
ANCE REQUIRED FOR
T
O
-
i. Install
ARD MOUNTING HOLES
headboard.
13. Install mattress on
the foundation.
Typical Precision
Comfort™ installation
is now complete.
MEASURE FLANGE SL
CENTER-
HEADBO
T
O
-
CENTER T
ARD HOLE L
O
T
S
O
CHECK
OCA
TION
FIGURE 12: Headboard bracket measurement and adjustment to accept headboard.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Sleep Number MATTRESS INSTALLATION
INSTALLATION INSTRUCTIONS
Tools required—utility knife, Phillips® head screwdriver.
Install the Sleep Number® mattress, per
the following procedure:
1. Verify Precision Comfort® adjustable
foundation setup is complete.
IMPORTANT: Wash hands before
beginning installation. Residue on
hands will easily transfer to cloth
covered bedding components.
2. Identify and remove (2) locator pins in the
adjustable foundation (FIGURES 13 and
14). Note: approximate locator pin
position is 32-1/2” from the top and 6”
from the side of the adjustable
“A” = 32-1/2” (approx.)
“B” = 6” (approx.)
A
B
foundation. Locator pins mark threaded
lug location used for Sleep Number®
mattress attachment.
APPROXIMATE
LOCATOR PIN
POSITION
3. Unzip the top panel of the
Sleep Number® mattress
cover and set the panel
aside.
4. Position the bottom of the
Sleep Number® mattress on top
of the adjustable foundation.
FIGURE 13
5. Insert foam border walls and
corner locks into the mattress cover per
the Sleep Number® mattress installation
instructions.
6. Align the Sleep Number® mattress cover
flush against the adjustable foundation
mattress retainer bar (at the foot end of the
bed). Align the top and side edges of the
mattress cover flush with the adjustable
foundation so the mattress cover and the
foundation are a matched pair.
7. Locate the 2 threaded lug mounting
locations (with fingers).
PULL OUT EACH PIN FROM
THE THREADED LUGS.
FIGURE 14: Locator pin removal.
NOTE
EXACT SIDE AND END ALIGNMENT OF THE
SLEEP NUMBER® MATTRESS COVER
ASSEMBLY WITH THE ADJUSTABLE
FOUNDATION MUST BE ACHIEVED BEFORE
PROCEEDING TO STEP 8.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Sleep Number MATTRESS INSTALLATION
13. Complete mattress setup per the Sleep
Number® installation instructions. This will
include fitting the base pad, air chambers,
center wall and topper pad.
EXERCISE EXTREME CAUTION WHEN
USING UTILITY KNIFE! THE DANGER OF
SERIOUS FINGER CUTS ARE POSSIBLE IF
UTILITY KNIFE IS NOT USED CORRECTLY.
14. Position and zip the top panel to the Sleep
Number® mattress cover to complete
installation.
8. At each threaded lug location, make a
small cut (no larger than 1/4” long) through
the mattress cover fabric with a utility knife
(FIGURE 15).
NOTE
SLEEP NUMBER® MATTRESS HARDWARE
AND COMPONENTS VARY PER MODEL.
9. Position a large plastic washer over each
cut in the mattress cover fabric (FIGURE
15).
10. Position a metal washer over each plastic
washer (FIGURE 15).
11. Insert one of the mounting bolts through
both washers and screw into one of the
mounting lugs. Snug fit...Do not
overtighten!
12. Insert the other mounting bolt per Step 11.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Sleep Number MATTRESS INSTALLATION
NOTE
IF ADJUSTABLE FOUNDATION SERVICE IS
REQUIRED, REMOVE THE SLEEP NUMBERÆ
MATTRESS BEFORE THE SERVICE
TECHNICIAN ARRIVES.
MOUNTING
BOLTS
METAL
WASHERS
LARGE
PLASTIC
WASHERS
FOAM WALL
CENTER SECTION
CORNER
LOCK (4)
FOAM WALL
SECTIONS
CUT 1/4 INCH SLIT
THROUGH BOTTOM
FABRIC PANEL OF
MATTRESS COVER
SLEEP NUMBER®
MATTRESS COVER
EQUIPPED WITH
ZIPPERED TOP PANEL
ADJUSTABLE
FOUNDATION
IMPORTANT: make
certain all 4 sides of the
Sleep Number® mattress
cover are flush aligned
with the adjustable
foundation before cutting
small slit (no larger than
1/4” long) in the bottom
panel of the mattress
cover.
LOCATOR PINS
(THREADED LUG
LOCATION)
MATTRESS RETAINER BAR
(FOOT END OF BED)
FIGURE 15
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HAND CONTROL OPERATION
TRANSMISSION
INDICATOR LIGHT
POSITION RECALL BUTTONS
Press to recall a massage/wave
setting assigned by the program
set button.
MASSAGE SET BUTTON
Press to capture a setting of the
massage and/or wave functions
as a programmed position. Press
the favorite massage button to
activate the preset position.
FOOT UP/DOWN BUTTON
Press and hold to raise or
lower the foot section.
FLAT BUTTON
Press to return bed to the
level position.
HEAD UP/DOWN BUTTON
Press and hold to raise or lower
the head section.
FAVORITE MASSAGE BUTTON
Press to recall a massage and/or
wave function set by the massage
set button.
HEAD MASSAGE BUTTONS
Press and hold to increase or
decrease head massage intensity.
FOOT MASSAGE BUTTONS
Press and hold to increase or
decrease foot massage intensity.
HEAD MASSAGE ON/OFF BUTTON
Switches head massage on or off.
When switched on, the massage
function will automatically shut off
after 30 minutes.
FOOT MASSAGE ON/OFF BUTTON
Switches foot massage on or off.
When switched on, the massage
function will automatically shut off
after 30 minutes.
WAVE SPEED BUTTONS
Press and hold—after the head
and foot massagers, and the
wave system have been
WAVE ON/OFF BUTTON
Press to activate or deactivate
the wave vibration system.
activated—to increase or
decrease the wave speed.
NOTE
HAND CONTROL REQUIRES FOUR (4) AAA SIZE BATTERIES. TO CONSERVE
BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY
BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEIVER UNIT OPERATION
In case of a power outage, press and hold
POWER
DOWN BOX
the learn button on the receiver unit
(power down box) to lower the bed to the
flat position (FIGURE 18).
LEARN
BUTTON
This function is only for lowering the bed
and will not operate the bed to any other
position. The (2) 9 volt batteries should be
replaced after this function is used.
In the event the power down feature does
not work, check to make sure the (2) 9 volt
batteries are good.
FIGURE 16: Power down box learn button.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING 1 hand control - 1 bed
The two step procedure below is required to program 1 hand control to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical
outlet.
STEP 1
Locate the receiver unit (power down box)
for the bed and press the learn button
for 1 second and release (FIGURE 16).
POWER
DOWN BOX
LEARN
BUTTON
TRANSMISSION
INDICATOR LIGHT
POS 1
BUTTON
FIGURE 16: Power down box learn button.
STEP 2
On the hand control, simultaneously press
and hold the POS 1 and head massage on/
off buttons (FIGURE 17). The transmission
indicator light will flash slowly and then
flash rapidly. Continue to hold for 5
seconds and then release the buttons.
HEAD MASSAGE
ON/OFF BUTTON
FIGURE 17
One hand control is now programmed to
operate one bed.
NOTE
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING 2 hand controls - 1 bed
The three step procedure below is required to program 2 hand controls to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical
outlet.
STEP 1
Locate the power down box for the bed
and press the learn button for 1 second
and release (FIGURE 16).
HAND
HAND
POWER
DOWN BOX
CONTROL 1 CONTROL 2
LEARN
BUTTON
TRANSMISSION
INDICATOR LIGHT
POS 1
BUTTON
FIGURE 16: Power down box learn button.
STEP 2
On hand control 1, simultaneously press
and hold the POS 1 and the head massage
on/off buttons (FIGURE 17). The
transmission indicator light will flash
slowly and then flash rapidly. Continue to
hold for 5 seconds and then release the
buttons.
HEAD MASSAGE
ON/OFF BUTTON
FIGURE 17
STEP 3
NOTE
Repeat Step 1 and Step 2 with hand
control 2.
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
Two hand controls are now programmed
to operate one bed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING 1 hand control - 2 beds
The three step procedure below is required to program 1 hand control to operate 2 beds.
Before beginning, make certain the beds are plugged into a working grounded electrical
outlet.
STEP 1
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 16).
BED 1
POWER
DOWN BOX
LEARN
BUTTON
BED 2
TRANSMISSION
INDICATOR LIGHT
POS 1
BUTTON
FIGURE 16: Power down box learn button.
STEP 2
On the hand control, simultaneously press
and hold the POS 1 and the head massage
on/off buttons (FIGURE 17). The
transmission indicator light will flash
slowly and then flash rapidly. Continue to
hold for 5 seconds and then release the
buttons.
HEAD MASSAGE
ON/OFF BUTTON
STEP 3
Repeat Step 1 and Step 2 with bed 2
FIGURE 17
One hand control is now programmed to
operate two beds.
NOTE
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING 2 hand controls - 2 beds
The six step procedure below is required to program 2 hand controls to operate 2 beds.
Before beginning, make certain the beds are plugged into a working grounded electrical
outlet.
STEP 1
STEP 6
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 16).
Repeat Step 4 and Step 5 with hand control 2.
Two hand controls are now programmed to
operate two beds.
POWER
DOWN BOX
LEARN
BUTTON
HAND CONTROL 1
BED 1
FIGURE 16: Power down box learn button.
HAND CONTROL 2
BED 2
STEP 2
TRANSMISSION
INDICATOR LIGHT
On hand control 1, simultaneously press and
hold the POS 1 and the head massage on/off
buttons (FIGURE 17). The transmission
indicator light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
POS 1
BUTTON
STEP 3
Repeat Step 1 and Step 2 with hand control 2.
STEP 4
Locate the power down box for bed 2 and
press the learn button for 1 second and
release. (FIGURE 16).
HEAD MASSAGE
ON/OFF BUTTON
STEP 5
On hand control 1, simultaneously press and
hold the POS 1 and the head massage on/off
buttons (FIGURE 17). The transmission
indicator light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
FIGURE 17
NOTE
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING separating 2 beds
The six step procedure below is required to separate 2 hand controls from operating 2 beds.
One hand control per bed operation will result. Before beginning, make certain the beds are
plugged into a working grounded electrical outlet.
STEP 1
STEP 6
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 16).
Repeat Step 4 and Step 5 with hand control 2.
Independent hand control operation is now
restored (hand control 1 operating bed 1;
hand control 2 operating bed 2).
POWER
DOWN BOX
LEARN
BUTTON
HAND CONTROL 1
BED 1
FIGURE 16: Power down box learn button.
HAND CONTROL 2
BED 2
STEP 2
On hand control 1, simultaneously press and
hold the POS 1 and the head massage on/off
buttons (FIGURE 17). The transmission
indicator light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
TRANSMISSION
INDICATOR LIGHT
POS 1
BUTTON
STEP 3
Repeat Step 1 and Step 2 with hand control 1.
Note: wait 90 seconds before proceeding to
Step 4.
STEP 4
Locate the power down box for bed 2 and
press the learn button for 1 second and
release. The bed will be equipped with
either a power down box or J box (FIGURE
16).
HEAD MASSAGE
ON/OFF BUTTON
STEP 5
FIGURE 17
On hand control 2, simultaneously press and
hold the POS 1 and the head massage on/off
buttons (FIGURE 17). The transmission
indicator light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
NOTE
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Precision Comfort™ OPTIONAL EQUIPMENT
Contact your nearest Select Comfort® retail dealer or call toll free at 800-582-7216 for
accessory pricing and to order the accessories indicated in the chart below:
ACCESSORY DESCRIPTION
CODE
Glides1 (set of 4, replaces legs)
107397
107399
107396
107398
7” Legs (set of 4)
Swing-away Hinges
Bed Straps (connects 2 Precision Comfort® foundations together)
1 Headboard brackets cannot be used with glides.
107397
7”
107396
107398
107399
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
In the event the Precision Comfort™ adjustable bed fails to operate, investigate the
symptoms and possible solutions provided in the chart below:
SYMPTOM
SOLUTION
• Verify power cord is plugged into a working,
grounded electrical outlet. A grounded,
electrical surge protection device is recommended.
Test outlet by plugging in another working appliance.
Hand control illuminates and appears to be
operable, but will not activate bed.
• Program the hand control (see Programming, for
procedures). If equipped with power down box, make
certain power down box is easily accessible. Relocate
power down box if required.
• Unplug power cord, wait 45 seconds and plug in to
reset electronic components.
No features of the adjustable bed will activate.
Hand control will not illuminate.
• Electrical circuit breaker may be tripped. Check
electrical service breaker box to verify.
• Defective surge protection device or electrical outlet.
Test outlet by plugging in another working appliance.
• Replace batteries in the hand control.
• Bed mechanism may be obstructed. Elevate bed and
check for obstruction. Remove obstruction.
• Head section may be too close to the wall.
Head or foot section will elevate, but will not
return to the horizontal (flat) position.
• Headboard may be too close the edge of the mattress.
Verify a 1.5’” (38.1mm) to 2” (50.8mm) distance
between headboard brackets and mattress. Adjust if
required.
• Verify headboard brackets were removed during
installation. Remove headboard brackets if still
attached to the underneath side of bed.
• If bed is located on hard surface flooring, place carpet
pieces or rubber caster cups under each leg or caster
of the bed. (see accessory sheet, included with this
product, for rubber caster cup order information).
• Elevate the head or foot section a short distance (with
the hand control) to realign the lift/lower mechanisms
with the bed support platform.
Excessive massage motor noise.
• Verify that bed is not positioned against a wall,
nightstand, or other object that may cause vibration or
noise.
• If adjustable bed is installed over a bed frame, verify
massage motors are not causing bed frame (or bed
frame components) to vibrate.
• Verify that headboard attachment hardware is
tightened firmly (if used).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2-20 WARRANTY
Leggett & Platt, Incorporated (“L&P”) warrants this adjustable bed to the consumer who is the
original purchaser (the “purchaser”), subject to the terms and conditions set forth herein. This
warranty begins on the “warranty commencement date” which is the date of purchase for new
unused beds and the date of manufacture for beds that have been used as floor or display
models. Thus, on a floor model bed, the warranty is a portion of the limited 20-year warranty.
FULL 1 YEAR WARRANTY
remainder of the cost of the replacement
part. This twenty (20) year warranty shall not
apply unless the defective part is returned to
L&P within ten (10) days of purchaser’s
receipt of the replacement part. Purchaser
shall pay all service and transportation costs
related to the replacement of the defective
part. After the twentieth year, purchaser shall
bear the entire cost of repair and
This adjustable bed is warranted against
defects in the workmanship or materials for
a period of one year from the warranty
commencement date. Upon notice during
the first year after the warranty
commencement date, L&P will repair or
replace (at no cost to the purchaser) any
defective adjustable bed part, and L&P will
pay all authorized labor and transportation
costs associated with the repair or
replacement of any parts found to be
defective.
replacement of all parts and materials,
including labor and transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any
damage caused by the purchaser; (b) if there
has been any repair or replacement of
adjustable bed parts by an unauthorized
person; (c) if the adjustable bed has been
mishandled (whether in transit or by other
means), subjected to physical or electrical
abuse or misuse, or otherwise operated in
any manner inconsistent with the operation
and maintenance procedures outlined in the
Owners Manual and this warranty; (d) to
damage to mattresses, fabric, cables,
electrical cords or items supplied by dealers.
Contact the dealer for warranty information
on these items; (e) if there has been any
modification of the adjustable bed without
prior written consent by L&P; (f) to costs for
unnecessary service calls, including costs
for in-home service calls solely for the
purpose of educating the consumer about
the adjustable bed or finding an
2-YEAR LIMITED WARRANTY
During the second year from the warranty
commencement date, upon receipt of notice,
L&P will replace any adjustable bed part
found to be defective. This limited two year
warranty shall not apply unless the defective
part is returned to L&P within ten (10) days of
purchaser’s receipt of the replacement part.
Purchaser shall pay all service and
transportation costs related to the
replacement of the defective part.
20-YEAR LIMITED WARRANTY
Upon notice during the third through the
twentieth years from the warranty
commencement date, L&P will replace, upon
terms and conditions set forth in this
paragraph, any mechanical bed part found
to be defective. Electronics, electrical
components, drive motors and massage
motors are excluded. Purchaser shall pay 1/18
of the then current replacement cost of the
defective part multiplied by the number of years
after two (2) years from the warranty
unsatisfactory power connection; (g) if the
recommended weight restrictions are not
followed (300-Twin; 375-Full; 425-Queen),
the warranty will be void.
commencement date, and L&P shall bear the
Continued on back of page...
25
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2-20 WARRANTY
Repairs to or replacement of an adjustable
It is the sole responsibility of the purchaser
to provide adequate space and accessibility
to the adjustable bed. In the event that the
technician is unable to perform service due
to lack of accessibility, the service call will be
billed to the purchaser and the service will
have to be rescheduled.
bed or its components under the terms of
this limited warranty will apply to the original
warranty period and will not serve to extend
such period.
The decision to repair or to replace defective
parts under this warranty shall be made, or
cause to be made, by L&P at its option and in
its sole discretion.
L&P makes no other warranty whatever,
express or implied, and all implied
warranties of merchantability and fitness
for a particular purpose are disclaimed by
L&P and excluded from this agreement.
Repair or replacement shall be the sole
remedy of the purchaser. There shall be no
liability on the part of L&P for any special,
indirect, incidental, or consequential
damages or for any other damage, claim, or
loss not expressly covered by the terms of
this warranty.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or
exclusion may not apply to every purchaser.
This warranty gives the purchaser specific
legal rights, and the purchaser may also
have other rights, which may vary from state
to state. This warranty is valid in all 50
states, Puerto Rico, and Canada.
This limited warranty does not include
reimbursement for inconvenience,
removal, installation, setup time, loss of
use, shipping, or any other costs or
expenses. Leggett & Platt or its service
technicians shall not be responsible for
moving furniture, removing headboards &
footboards or any other items in order to
perform service on your adjustable bed.
CONTACT INFORMATION
Select Comfort
Customer Service Department
6105 Trenton Lane North
Minneapolis, MN 55442
800-580-7216
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|