U00086051203
User's Guide
Solvent Ink
Color Inkjet Printer
IP-6600
Read this User's Guide to use the printer safely and
properly. Keep this manual in a place where you
can quickly access it at any time.
Seiko I Infotech Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you very much for purchasing the IP-6600 Color Inkjet
Printer (simply called the printer below).
This printer is a color inkjet printer that adopts solvent ink, supports
64 inch media width, and builts-in SCSI interface.
This manual, the IP-6600 User's Guide, describes the features of
the printer, names of components, information to be known before
use, and basic operations, such as how to turn the power on and off
and set media and ink.
The following items should be read before reading Section 1.
- Deliverables
- Safety precautions
- Handling precautions
- Manual legend (notation rules)
Read these items to use the printer safely and properly. Keep this
manual in a place where you can quickly access it at any time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Deliverables
The printer components, including options, are installed on the main
unit on delivery. Make sure that the following items are present.
If any parts are missing or damaged, contact the shop where you
purchased the product or the nearest service dealer.
Basic components
Printer main unit <1>
• Built-in SCSI interface.
• Including a winding unit.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
SCSI cable
<1>
Roll paper(for installations)
<1>
Power cord
<2>
• Power cord for printer
• Power cord for heater
+ screw driver
(for head up/down adjustment)
Maintenance kit IP6-108
<1 set>
• Cap cleaning liquid: 100 ml
• Wiper cleaning liquid: 100 ml
• Cleaning swab: 50 pieces
• Syringe: 10 pieces
Starter kit 6 colors IP6-100
(Y, M, C, Bk, Lc, Lm)
<1>
User's Guide
<1 copy>
Waste ink bottle IP6-109
<1>
Paper tube 64" (For winding unit)
<1>
*: Ink capacity of each ink cartridge for starter kit 6 colors IP6-100 is 500ml.
Approximately 100 ml ink for each color is consumed at initial ink charge. Therefore, this 100 ml ink for each
color cannot be used for print.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
• Dryer 64
(IP-260) : 1
(IP-263) : 1
(IP-261) : 1
(IP-262) : 1
(IP-540) : 1
(IP-541) : 1
• Dryer 64 for North America
• Roll Cover 64
• Exhaust Attachment
• PS RIP (Photo Print 4 Dx)
• PS RIP (Photo Print 4 Server)
Consumables
Storage Kit IP6-137
<1 set>
Maintenance Kit IP6-108
<1 set>
Cleaning Kit IP6-117
<1 set>
• Maintenance liquid cartridge: 6
• Dummy cartridge: 6
• Cap cleaning liquid: 100 ml
• Wiper cleaning liquid: 100 ml
• Cleaning swab: 50 pieces
• Syringe: 10 pieces
• Cleaning liquid cartridge: 6
• Dummy cartridge: 6
Cap cleaning liquid: 6 bottles
IP6-138 < 1 set >
Wiper cleaning liquid: 6 bottles
Cleaning swab
IP6-147
IP6-139 < 1 set >
Cap cleaning liquid (100ml) : 6 bottles
<300 pieces>
• Wiper cleaning liquid (100ml) : 6 bottles
• Syringe: 10 pieces
Ink cartridges IP6-XXX
(Y, M, C, Bk, Lc, Lm)
Waste ink bottle IP6-109
<1>
See page 1-8 for the item number.
* : Options and consumables can be ordered separately.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
The following symbols are used in this manual to ensure the proper
use of the printer and to prevent the printer from being damaged.
Follow the instructions marked with these symbols.
Serious personal injury or death:
Failure to follow the guidelines marked with
WARNING
this symbol could result in serious personal
injury or death.
Minor personal injury or product and/or
peripheral damage:
Failure to follow the guidelines marked with
this symbol could result in minor personal
injury or product and/or peripheral damage.
CAUTION
Example of symbols:
This symbol ( ) denotes items that require special care
while executing a certain procedure or operation.
This symbol ( ) denotes items that are forbidden.
This symbol ( ) denotes items you should follow to
prevent accidents or injury.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Use the power supply voltage specified on the nameplate. DO NOT
plug several devices into one electrical outlet as this might result in fire
or electric shock.
Make sure the printer is well grounded. If not, a short circuit may cause
fire or electrical shock.
DO NOT disassemble or remodel the printer. DO NOT repair the printer
by yourself. Doing so may cause fire, electric shock or other accidents.
DO NOT damage, break, process, or heat the power cable. If it is
damaged, replace it with a new one. Using a damaged power cable may
cause fire or electric shock.
NEVER use the printer in a place of extreme humidity or any place
where it can possibly be splashed by any liquids. If any liquids get into
the printer, it could lead to fire, electric shock, or other serious accidents.
DO NOT remove the covers attached to the printer because they contain
high-voltage and extremely hot parts. Careless removal might result in
an electric shock or burn.
DO NOT allow metal or liquids to touch the internal parts of the printer.
Doing so may cause fire, electric shock, or other accidents.
DO NOT disconnect or connect the power cable with wet hands. Doing
so may lead to electric shock.
Turn the printer off and unplug the power cable immediately after it
thundered.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Power OFF the printer and unplug the power cable from the power outlet
in any of the following cases:
• When putting your hands inside the printer.
• Smoke, strange noise or smells generate from the printer.
• A piece of metal or any liquid touches the internal parts or slot of
the printer.
• An error requiring service by a service center occurs.
DO NOT put your hand into the paper delivery slot as it may lead to
injury by the cutting device.
Do not leave the printer stained with ink.
The coating of the printer may be damaged.
The ink used for the device contains organic solvent
(Ethylenglycolmonbutyleteracetat).
Therefore, observe the local rules strictly related to organic solvent stuff.
The ink used for the device contains organic solvent
(Ethylenglycolmonobutyletheracetat), Since the ink is flammable, never
use fire when using the device.
Do not swallow ink or avoid its splashes on the eye. If it gets into the
eye, wash it off with a clean running water and consult a doctor as
required. If it is swallowed, do not try to vomit it forcefully, but cunsult
a doctor.
Keep ink cartridges out of reach of children.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Handle the paper rolls with care because they are very heavy. If you
drop them, it could lead to personal injury.
Hold the electric cable by the plug when connecting or disconnecting it.
Failing to do so may cause the cable to fray or break which could lead to
electric shock and/or fire.
DO NOT get ink on your skin or clothes. Wash off any ink immediately
with soapy water.
DO NOT put any paper rolls on an unstable table or a tilted surface as
they could fall leading to an injury.
The heater will be hot.
Pay attention not to touch and not to be burned.
In order to ensure the safe operation of the printer heed all of the cautions
and warnings contained throughout this manual.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Precautions
Power Supply
1. Install the printer near an easily accessible electrical outlet.
2. Do not provide power to the printer through the same power
line as for noise-generating devices, such as a motor.
3. Use the power supply matched with the specification of the
printer.
4. Connect the power cable to an electrical outlet. Do not plug
several devices into one electrical outlet.
Printer
1. Do not place anything on top of the printer. Do not rest your
elbows on the printer.
2. Open and close the top cover gently from the front of the printer
with both hands.
3. Before connecting or disconnecting the interface connector, turn
the printer off.
4. Do not clean the surface of the cover with benzene or paint
thinner. The coating may come off or deteriorate.
Wipe the cover clean with a soft cloth. If the cover is very dirty,
use a cloth moistened with a neutral detergent.
5. Do not touch the ink-jet head surface.
Regular Inspection and Maintenance
The following regular inspection and maintenance must be
performed in terms of characteristics of solvent ink.
1. Clean the capping unit and wiper blade every day.
2. Check moisture of wiper sponge every day.
3. Perform the head cleaning every one month.
4. Perform the service cleaning when leaving the printer for long
time (2 weeks or more at power off state.)
5. Perform the head wash and the ink charge before printing when
leaving the priner for long time.
See pages 2-62 and 2-73 for regular inspection and maintenance.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
1. Always use the recommended consumables (media, ink, etc.).
Failure to follow this instruction may cause poor print quality
or a breakdown.
2. Do not use ink past the date of expiration as this may cause a
breakdown.
3. Put a used ink cartridge into a plastic bag and dispose of it as an
industrial waste. Observe any regulations for disposal of waste
ink bottles.
4. Do not get ink on your skin or clothes. Wash off any ink
immediately with soapy water.
5. Check waste ink bottle regularly so as not to leak the waste ink.
6. When the waste ink bottle is installed or removed, spread the
stain preventing sheet so as not to stain the floor with spilt ink.
7. Store ink in a dark and cool place.
NEVER store ink in a high temperature or direct sunshining
place.
Doing so, ink may cause characteristic changes.
8. Do not attempt to disassemble ink cantridges.
9. Media for solvent ink on the market can be used for this printer.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Legend (Notational rules)
This manual uses the notational rules for marks, keys, LCDs, and
LEDs:
Marks
WARNING
Boxes marked with a "WARNING" describe points of caution for
avoiding serious personal injury.
CAUTION
Boxes marked with a "CAUTION" describe points of caution for
avoiding injury to yourself or damage to the printer.
NOTE
Boxes marked with a note describe precautions while handling the
printer.
HINT: Hint mark
The hint symbol describes operations that make using or
HINT
handling the printer easier.
Reference mark
This mark is followed by a reference section or page number.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Notation of Keys/LCDs/LEDs
Example 1: Keys and messages shown on the LCDs in the text
This represents a key
on the operation panel.
This represents the LC display
on the operation panel.
Press
to put the
= = INK
PAPER
ENTRY
F•ADJ
1
2
printer offline.
Press
to select
SERVICE
CLEANING
FEED
the first menu in the
local operation mode.
Press
again to
3
4
FUNC
ADJUST
SYSTEM
RESET
select the second menu
in the local operation
mode.
Press
to enter the
This represents a key to seledt the
menu. (Ex. key)
function menu.
:
Example 2: LED's states in the text
LED's states of "On", "flashing", and "Off" are characterized by the following
symbols:
On
Flashing
Off
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 3: LCD's state transitions and key operations in the text
INK
PAPER
ENTRY
F. ADJ
INITIALIZING
WAIT A MOMENT
A key on the
operation panel.
SERVICE
FEED
PRINT READY
CLEANING
ROLL : 64" (COATED)
This shows that the LCD screen
changes to another when the operator
presses a key.
This indicates that the LCD screen
changes to another automatically without
pressing a key.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction
Deliverables ......................................................................................... i
Safety Precautions..............................................................................iv
Handling Precautions........................................................................ viii
Manual Legend (Notational rules)....................................................... x
Section 1 Getting Started (Basic knowledge)
1-1
Operating Conditions ....................................................................... 1-2
Installation Space ................................................................ 1-2
Environmental Conditions ................................................... 1-3
Consumables................................................................................... 1-5
Media/Paper ........................................................................ 1-5
Ink .................................................................................... 1-8
Waste Ink Bottle ................................................................ 1-10
Maintenance Kit................................................................. 1-11
Cap Cleaning Liquid 6 Bottles ........................................... 1-12
Wiper Cleaning Liquid 6 Bottles ........................................ 1-12
Cleaning Swab .................................................................. 1-12
Storage Kit......................................................................... 1-12
Cleaning Kit ....................................................................... 1-12
External Views, Part Names, and Functions ................................. 1-13
Front .................................................................................. 1-13
Rear .................................................................................. 1-14
Heater................................................................................ 1-15
Operation Panel ................................................................ 1-16
Heater Control Panel ......................................................... 1-18
Dryer 64 (Option)............................................................... 1-19
Roll Cover 64 (Option)....................................................... 1-19
Exhaust Attachment (Option) ............................................ 1-19
PS RIP (PhotoPrint 4 DX) (Option) ................................... 1-19
CONTENTS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PS RIP (PhotoPrint 4 Server) (Option) .............................. 1-19
LCD Messages and Printer State .................................................. 1-20
Messages on the LCD ....................................................... 1-20
F/W version checking method ....................................................... 1-24
F/W version checking method ........................................... 1-24
Added Functions in V2.00 ................................................. 1-24
Section 2 Basic Operations
2-1
Connecting with Computer .............................................................. 2-2
System configuration (connection example) ....................... 2-2
Connection procedure ......................................................... 2-2
Turning the Power On/Off................................................................ 2-5
Turning the Power On ......................................................... 2-6
Turning the Power Off ......................................................... 2-9
Replacing the Paper Roll ............................................................... 2-11
Installing Paper Roll in the Printer ..................................... 2-11
Removing the Paper Roll from the Printer......................... 2-17
Replacing Paper Roll with Another.................................... 2-18
Replacing Empty Paper Roll.............................................. 2-18
Replacing Jammed Paper Roll .......................................... 2-18
Installing/Removing Cut Sheet in/from the Printer ............ 2-19
Paper Feed Adjustment Correction Value Setting............. 2-19
Change during online printing ........................................... 2-24
Head print position adjustment .......................................... 2-24
Replacing Ink Cartridges ............................................................... 2-31
Ink Cartridge Replacement Procedure .............................. 2-31
Replacing Empty Ink Cartridge.......................................... 2-33
If an Ink Cartridge Is Not Installed ..................................... 2-34
Replacing Cartridges during Printing................................. 2-35
If an Ink Cartridge Is Not Detected .................................... 2-37
CONTENTS-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Waste Ink Bottle...................................................... 2-38
Waste Ink Bottle Replacement Procedure......................... 2-38
If the Waste Ink Bottle Is Full............................................. 2-40
If the Waste Ink Bottle Is Not Installed .............................. 2-41
Head Cleaning "CLEANING" ......................................................... 2-42
Paper Feed "FEED" ....................................................................... 2-44
Using the Origin Point Setting Function ............................ 2-45
Installing Paper on Winder............................................................. 2-48
Changing Heater Control Setting Temperature ............................. 2-53
Using the Media Pressure Alternation Lever ................................. 2-56
Using the Head Up/Down Lever .................................................... 2-57
Using the Media Edge Guard ........................................................ 2-59
Using the FAN Guard Slide Lever ................................................. 2-60
Using the Print Pause/Restart and Cancel Keys ........................... 2-61
Inspection & Maintenance ............................................................. 2-62
Section 3 Operation Panel Menu Operations
3-1
Basic Menu Operation ..................................................................... 3-2
Menu Hierarchical Structure ................................................ 3-2
Menu Tree ........................................................................... 3-3
Basic Operations and Keys ................................................. 3-8
Operation Procedure for Choice Input, Value Input,
Execution, and Character Input ........................................... 3-9
Menu Operations ........................................................................... 3-15
INK Menu .......................................................................... 3-15
PAPER Menu .................................................................... 3-16
ENTRY Menu .................................................................... 3-17
F.ADJ Menu....................................................................... 3-35
SERVICE Menu................................................................. 3-38
CLEANING Menu .............................................................. 3-41
CONTENTS-3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEED Menu ....................................................................... 3-42
FUNC Menu....................................................................... 3-42
ADJUST Menu................................................................... 3-44
SYSTEM Menu.................................................................. 3-47
RESET Menu..................................................................... 3-51
Section 4 Heater Controller Operation
4-1
Temperature Control........................................................................ 4-2
LCD Display ..................................................................................... 4-4
Parameter Setup Mode.................................................................... 4-6
Error Messages ............................................................................. 4-10
Section 5 Troubleshooting
5-1
Troubleshooting ............................................................................... 5-2
Clearing Paper Jam ......................................................................... 5-3
When an Error Message Appears ................................................... 5-4
Service Call Errors............................................................... 5-4
Communication Errors......................................................... 5-6
Operator Call Errors ............................................................ 5-7
When the Printer Fails to Work Correctly ...................................... 5-11
When a Print Error Occurs............................................................. 5-12
When There Is an Abnormal Sound .............................................. 5-13
Appendix
A-1
Basic Specifications......................................................................... A-2
Printer Specifications...........................................................A-2
Options/Consumables .....................................................................A-3
Options ................................................................................ A-3
Consumables.......................................................................A-4
Celsius and Fahrenheit Conversion List ..........................................A-5
CONTENTS-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1 Getting Started
(Basic knowledge)
This section provides necessary information to operate the
printer. Familiarize yourself with the basics of the printer
before reading Section 2 and later.
Contents of this section
Operating Conditions
Installation Space
Environmental Conditions
Consumables
Media/Paper
Ink
Waste Ink Bottle
Maintenance Kit
Cap Cleaning Liquid 6 Bottles
Wiper Cleaning Liquid 6 Bottles
Cleaning Swab
Storage Kit
Cleaning Kit
Maintenance Liquid Cartridge
External Views, Names of Parts, and Functions
Front
Rear
Heater
Operation Panel
Heater Control Panel
Dryer 64
Roll Cover 64
Exhaust Attachment
PS RIP (PhotoPrint 4 DX)
PS RIP (PhotoPrint 4 Server)
LCD Messages and Printer State
Messages on the LCD
F/W Version Checking Method
F/W Version Checking Method
Added Functions in V2.00
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Conditions
This section describes the operating conditions for the printer.
Installation Space
There must be a sufficient space around the printer for the
replacement of frequently used parts, for the output of drawings,
and for ventilation. In addition, the maintenance space, shown
below, is required to repair the printer or replace components.
The installation/maintenance space is shown in the following figure.
Installation and maintenance space
400
400
(Front side)
Height direction: 1700
(Unit : mm)
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Conditions
Environmental Conditions
Operating temperature and humidity levels
The printer should be used within the temperature and humidity
levels shown below.
Temperature: 15 °C to 30 °C
Humidity: 30% to 70%
-
-
To obtain better print quality, use the printer within
temperatures of 20 to 25 °C.
HINT
When operating temperature is lower than 20 °C, the print
speed goes down two-third of normal print speed to keep
a good print quality.
-
When the head temperature goes high, the print time is
delayed.
NOTE
-
When the printer is used out of range of the operating
temperature and humidity, the print may be stopped and
the print quality may be degraded.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Places where the printer must not be installed
Do not install the printer in the following places:
- Places exposed to direct sunlight
- Places subject to vibration
- Places with excessive dust
- Places subject to extreme changes in temperature or humidity
- Places near an air conditioner or a heater
- Places where the printer may get wet
- Places subject to direct air circulation from vents
- Places near a diazo copier that may generate ammonia gas
- Places with poor ventilation
- Unstable places
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
Media/Paper
Available media types
We prepared the following types of media:
• Glossy vinyle chrolide
• Matted vinyle chrolide
• Banner
Contact our service center for details.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for storing media
- Avoid direct sunlight and water regardless of before and after
opening the package. Put paper in envelope to prevent dust and
store media in a dry, cool and dark place.
- Avoid rapid change of temperature and humidity and store media
with no condensing.
- Do not store media in standing condition to prevent disorder of
media and damage of roll edge.
- Do not pile up media.
Precautions for disposing of paper
- Dispose of media in rule matched to the actual situation.
If there is a limitation for disposal regulations, follow the
regulations.
Precautions for use
- Avoid a change of temperature and humidity after opening
package.
Set media after leaving media in the operation environment for
3 hours or more. Use care for a change of humidity by turning
ON/OFF the air conditioner.
- In terms of media characteristics, curl of paper in low humidity
and wrinkle of media in high humidity may occur easily.
Use paper in normal temperature and humidity environment
(around 23 °C and 50%RH).
- Do not use scratched, wrinkled, curled, or stained with dust
media.
Especially, roll edge (both edges of roll) affects media feeding.
Also, do not drop or wet the media. If doing so, it may cause
bad effect to print quality and causes a malfunction.
- Hold margins of the media so as not to touch the print surface.
Adhesion of sebaceous matter or sweat may cause bad effect to
print quality.
- Amend mis-roll of the media before setting.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
Precautions for handling prints.
- Do not touch the print surface before drying up the ink.
Hold margins of the media for handling.
Especially use care before 24 hours after printing.
- Rubbing print surface causes color fading or color transfer.
Do not pile print surface to prevent color transfer.
- Do not pile together with copy prints or laser prints to prevent
sticking due to ink or toner.
- Do not rub, scratch, or hold the media to prevent pealing.
- Do not rub or leave the paper in wet condition to prevent blurring.
Other precautions
- Media causes color fading and a change in quality in getting
old.
Check paper condition and use well-conditioned paper.
- Paper dust due to cutting may cause float of coating.
- When using vinyl (with glue), adhesive matter (with glue) may
be sticked to the platen.
In this case, wipe up the adhesive matter referring to "Section 2,
Inspection & Maintenance".
Sticking of adhesive matter may cause paper jamming.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ink
Ink types
Use our recommended ink cartridges listed below.
Item No.
Ink color
Ink capacity
1000 ml
1000 ml
1000 ml
1000 ml
1000 ml
1000 ml
IP6-101 Y (Yellow)
IP6-102 M (Magenta)
IP6-103 C (Cyan)
IP6-104 Bk (Black)
IP6-105 Lc (Light Cyan)
IP6-106 Lm (Light Magenta)
NOTE
- Failure to use the recommended ink cartridge may lead to a
deterioration of the print quality or a printer malfunction.
- The valid period of the ink is 12 months after the manufacture
date.
- Do not shake ink cartridges before use.
- All six color cartridges must be installed.
If any of the cartridges is removed, a new one must be
installed.
Ink cartridges must be installed in all six slots. The positions of ink
cartridges are specified by color. (See the figure below.)
Black Light Magenta
Light Cyan
Yellow
Magenta
Cyan
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
WARNING
- Never bring the ink close to fire. Failure to follow this warning
might result in fire.
CAUTION
- Do not swallow ink or avoid its splashes on the eye. If it gets
into the eye, wash it off with a clean running water and consult
a doctor as required. If it is swallowed, do not try to vomit it
forcefully, but see a doctor.
- Do not attempt to disassemble ink cartridges.
Precautions for ink storage and processing
CAUTION
- Securely put a used ink cartridge into a plastic bag and
dispose of it as an industrial waste. Observe any regulations
for disposal of ink cartridges.
NOTE
- Ink has an expiration date. When it expires, the printer quality
may deteriorate or the printer may malfunction.
- Store ink cartridges in a dry, cool and dark place.
-Always use the recommended consumables (paper, ink, etc.).
Failure to follow this instruction may cause poor print quality
or a breakdown.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Waste Ink Bottle
Use our recommended waste ink bottle listed below.
Item No.
IP6-109
Remarks
1 piece
WARNING
- Never put the waste ink bottle near open flames. Failure to
follow this warning might result in fire.
CAUTION
- Do not swallow ink or avoid its splashes on the eye. If it gets
into the eye, wash it off with a clean running water and consult
a doctor as required. If it is swallowed, do not try to vomit it
forcefully, but see a doctor.
NOTE
- Install the waste ink bottle securely.
- A waste ink bottle must always be installed. If it is removed
for replacement, a new one must be installed.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
Precautions for handling the waste ink bottle
CAUTION
- After use, securely fasten the attached cap and dispose of
this product as industrial waste.
If you have any questions, please contact your nearest sales
office.
NOTE
- When the waste ink bottle is installed or removed, hold it
with both hands with its mouth facing up. If not, waste ink
may spill from the bottle.
Maintenance Kit
For cleaning the cap and wiper, use our specified cleaning liquid
respectively listed below.
Item No.
Remarks
Cap cleaning liquid
Wiper cleaning liquid
Cleaning swab
Quantity
100 ml
100 ml
IP6-108
50 pieces
10 pieces
Syringe
CAUTION
- Do not swallow ink or avoid its splashes on the eye. If it gets
into the eye, wash it off with a clean running water and consult
a doctor as required. If it is swallowed, do not try to vomit it
forcefully, but see a doctor.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cap Cleaning Liquid 6 Bottles
Item No.
Remarks
Cap cleaning liquid (100ml)
Quantity
IP6-138
6
Wiper Cleaning Liquid 6 Bottles
Item No.
Remarks
Quantity
Wiper cleaning liquid (100ml)
Syring
6
IP6-139
10
Cleaning Swab
Item No.
IP6-147
Remarks
300 pieces
Storage Kit
Item No.
IP6-137
Remarks
Quantity
Maintenance liquid cartridge (IP6-107)
Dummy cartridge (IP6-118)
6
6
Cleaning Kit
Item No.
Remarks
Quantity
Cleaning liquid cartridge (IP6-119)
Dummy cartridge (IP6-118)
6
6
IP6-117
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
External Views, Part Names, and Functions
This section shows the external views of the printer, the names of
parts of the printer and describes their functions.
Front
(7)
(2)
(1)
(6)
(3)
Ink cartridge
(4)
(3)
Roll paper
(4)
(5)
(8)
Lock
Unlock
(1) Operation panel
The lamps and LCD, which indicate the printer status, and keys for
setting functions are located on the operation panel.
The keys for setting heater temperature are located on the heater
control panel.
(2) Heater control panel
(3) Ink holder
(4) Flange
(5) Caster
Holds the ink cartridge.
Sets paper roll.
Unlocks the caster to move the printer, and lock it to secure the
printer.
(6) Paper pressure alternation lever
Alternates paper pressure depending on the paper thickness.
(7) Pressure roller up/down lever
Presses down the paper after inserting the paper into the paper
supplying part and releases the pressing down of the paper.
(8) Paper-out release lever (ME lever)
Releases paper-out detection sensor.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear
(24)
(20)
(20)
(11)
(23)
(15)
(16)
(21)
(22)
(19)
(10)
(13)
(12)
(14)
(18)
(9)
(17)
(9) Power receptacle
(10) Printer switch
(11) Rear cover
Printer power supply
SCSI controller
(12) SCSI connector
(13) ID switch
(14) Terminator switch
(15) Paper outlet
(16) Waste ink bottle
(17) Power receptacle
(18) Heater switch
Heater power supply
(19) 100 V/200 V alternation switch
(20) Cap cover
(21) Wiper cover
(22) Print stop/restart, cancel keys
(23) FAN guard potitioning slide bar
(24) Head up/down lever
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
External Views, Part Names, and Functions
Heater
Å
The printer builts in three heaters for fixing and stabilizing print
image on the print paper.
Pressure roller
Rear cover
(Front)
(Rear)
(27)
(25)
Paper roll
Paper outlet
(26)
Grid roller
Paper inlet
paper feed direction
(25) Front heater (Front)
(26) Print heater (Rear)
(27) Rear heater (Finish)
Preheats the paper.
Infiltrates ink into the paper and fixes ink.
Drys ink and stabilizes print image.
* Three heaters are controlled separately.
WARNING
-
Heaters become hot.
NEVER touch the heaters. If doing so, it could lead to
burn.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Panel
Keys, LEDs, and the LCD are laid out on the operation panel as
follows. It has a buzzer to alert errors or invalid key operations.
(4) LCD
Shows the printer status
and menus.
E
A
B
C
D
(3) Power switch
(2) Keys
Used to set printer functions.
Turns the printer ON
or OFF.
(1) LED
The LEDs light, flash, or turn off to
the status of the printer.
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
External Views, Part Names, and Functions
Functions of LCD, LEDs and keys
Name
Number
Function
Shows the data reception state.
- Flashing : Data is being received from the computer
- Off : No data is being received
(A) Data LED
(green)
Indicates whether an error has occurred.
- On : An error has occurred
- Flashing : Warning state (Winder time out error)
- Off : Normal (No error has occurred.)
(B) Error LED
(orange)
Shows whether there is the ink cartrige or indicates a warning.
- On : All ink cartridges are present.
- Flashing : Ink is running out. (One of color inks has run out.)
- Off : No ink (One of color inks has run out.)
(C) Ink LED
(green)
(1)
LED
Shows whether paper is set.
- On : Paper is set. (Roll paper or cut sheet is set.)
- Off : No paper (Neither roll paper nor cut sheet is set.)
(D) Paper LED
(green)
Shows whether the printer is online or offline.
(E) Online LED - On : Online
(green)
- Flashing : Online pause mode
- Off : Offline
ONLINE key
SHIFT Key
Switches between online and offline states.
Used as an auxiliary key for parameter input (switches the menu
level display).
CANCEL Key
ENTER Key
Key
Cancels an input parameter.
(2)
Key
Selects a menu or enters a parameter.
Key
Selects a menu group or switch a menu
(selection, number up/down).
Key
Key
(3)
Power switch
Power Switch Used to turn the printer ON or OFF.
Shows printer messages or status with alphanumeric characters,
katakana, or symbols (16 digits, two lines). Menus have a
(4)
LCD
LCD
hierarchical structure. Access each menu with
key.
,
,
,
or
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Heater Control Panel
Å
LCD
Rear Heater ON/OFF key
Front Heater ON/OFF key
Print Heater ON/OFF key
Front Heater UP/DOWN key
Rear Heater UP/DOWN key
Print Heater UP/DOWN key
Functions of LCD, LEDs and keys
Number
Name
Function and description
Indicates the setting temperature and the current temperature of the
front heater. When the main switch of the heater is turned off, it is
urged to turn on the main switch. When the front heater is turned off,
"OFF" is indicated.
FRONT
PRINT
REAR
Indicates the setting temperature and the current temperature of the
print heater. When the main switch of the heater is turned off it is
urged to turn on the main switch.
LCD
When the print heater is turned off, "OFF" is indicated.
Indicates the setting temperature and the current temperature of the rear
heater. When the main switch of the heater is turned off, it is urged to
turn on the main switch.
When the rear heater is turned off, "OFF" is indicated.
FRONT ON/OFF key Turns on/off the front heater.
FRONT UP key
Increases the setting value for the front heater.
FRONT DOWN key
PRINT ON/OFF key
PRINT UP key
Decreases the setting value for the front heater.
Turns on/off the print heater.
key
Increases the setting value for the print heater.
Decreases the setting value for the print heater.
Turns on/off the rear heater.
PRINT DOWN key
REAR ON/OFF key
REAR UP key
Increases the setting value for the rear heater.
Decreases the setting value for the rear heater.
REAR DOWN key
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
External Views, Part Names, and Functions
Dryer 64 (Option)
The dryer 64 dries the output media.
Roll Cover 64 (Option)
Protects paper roll from dust.
Exhaust Attachment (Option)
Mounts an exhaust gas pipe to the printer or the drying device.
PS RIP (PhotoPrint 4 DX) (Option)
PS RIP (PhotoPrint 4 Server) (Option)
RIP software for the IP-6600.
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Messages and Printer State
This section explains the messages shown on the LCD and outlines
menu operations.
Messages on the LCD
(1) Initialization display
The printer is being initialized.
Booting
INITIALIZING
WAIT A MOMENT
*: When the system starts normally, both controllers go
online and enter idle mode automatically.
(2) Online state (idle mode) display
The printer can receive data from the computer.
PRINT READY
ROLL : 64” (PAPER)
Status display
Paper information
*: When the
key is pressed in the menu mode,
"CLEANING" menu appears.
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Messages and Printer State
(3) Online state (print mode) display
The printer is printing.
PRINTING
ROLL : 64” (PAPER)
Status display
Paper information
(4) Online state (print pause mode) display
The printer is paused.
- Print stop and resume
PRINTING
ROLL : 64” (PAPER)
PRINT READY
ROLL : 64” (PAPER)
The ONLINE LED flashes.
Press the
key in the print pause mode to start the head cleaning.
- Print cancel (end)
PRINT READY
ROLL : 64” (PAPER)
The ONLINE LED flashes.
PRINT READY
ROLL : 64” (PAPER)
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Online state (print information mode) display
Paper total count and ink removing amount are displayed.
PRINT READY
ROLL : 64” (COATED)
TOTAL CT
XXXX
Bk INK REST:
Lm INK REST:
XXX%
XXX%
Three-second
intervals or
Lc INK REST:
Y INK REST:
XXX%
XXX%
Three-second
intervals or
M INK REST:
C INK REST:
XXX%
XXX%
Then, the printer returns to online idle mode.
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Messages and Printer State
(6) Offline (menu mode) display
Menus can be operated in offline mode.
INK
ENTRY
F•ADJ
PAPER
SERVICE
FEED
CLEANING
FUNC
SYSTEM
RESET
ADJUST
*:
,
,
, and
are access keys to menus.
*: When the
key is pressed in the menu mode, "CLEANING"
menu appears.
(7) Shutdown state display
The printer is shutting down.
SHUTDOWN
WAIT A MOMENT
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
F/W Version Checking Method
Here, the function added in V2.00 as a firmware version checking
method is described.
F/W Version Checking Method
(1) Select the OFFLINE mode. (Press the
key)
INK
ENTRY
PAPER
F•ADJ
(2) Press the
key to display "SYSTEM".
FUNC
SYSTEM
RESET
ADJUST
(3) Select "SYSTEM" with the
to display the firmware version.
key, and then press the
or
key
# F/W VERSION
* X.XX_YY
(4) The F/W version can be checked.
X.XX is the F/W version.
Added Functions in V2.00
The function that prints the maintenance history was added.
During the online print, the paper feed adjustment correction
1 History print
2 Paper feed adjustment
,
value can be changed temporarily with
keys.
The registered media information can be copied to a new
area.
3 Media entry
The mode that saves the waste ink quantity during auto
cleaning was added.
4 Waste ink value saving
The function that turns on the heaters even before the data is
received to save the waiting time until each heater
temperature becomes the set value.
Manual heater ON
function
5
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 Basic Operations
Contents of this section
Connecting with Computer
System configuration (connection example)
Connection procedure
Turning the Power On/Off
Turning the Power On
Turning the Power Off
Replacing the Paper Roll
Installing Paper Roll in the Printer
Removing the Paper Roll from the Printer
Replacing Paper Roll with Another
Replacing Empty Paper Roll
Replacing Jammed Paper Roll
Installing/Removing Cut Sheet in/from the Printer
Paper Feed Adjustment Correction Value Setting
Replacing Ink Cartridges
Ink Cartridge Replacement Procedure
Replacing Empty Ink Cartridge
If an Ink Cartridge Is Not Installed
Replacing Cartridges during Printing
If an Ink Cartridge Is Not Detected
Replacing the Waste Ink Bottle
Waste Ink Bottle Replacement Procedure
If the Waste Ink Bottle Is Full
If the Waste Ink Bottle Is Not Installed
Head Cleaning "CLEANING"
Paper Feed "FEED"
Using the Origin Point Setting Function
Installing Paper on Winder
Changing Heater Control Setting Temperature
Using the Media Pressure Alternation Lever
Using the Head Up/Down Lever
Using the Media Edge Guard
Using the FAN Guard Slide Lever
Using the Print Pause/Restart and Cancel Keys
Inspection & Maintenance
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with Computer
This section only shows system configurations and cable connection
procedure.
System configuration (connection example)
The following connection is possible.
(Printer server PostScript RIP)
Printer
SCSI interface
Connection procedure
Connect a cable as follows:
Turn the printer and the computer OFF.
NOTE
1
- When the printer is connected with the computer, turn the
printer ON, and then turn the computer ON. To turn the
system OFF, turn the computer OFF, and then turn the printer
OFF.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with Computer
Connect a SCSI cable to a SCSI connector on the rear of
the printer.
2
(It can be connected to any one of two SCSI connectors.)
NOTE
-
Use a dedicated SCSI cable (68-68-pin, 6 m).
If using a cable except the specified one, the printer can
not satisfy FCC and CE regulations.
SCSI connector
Set the ID switch on the rear of the printer.
3
Set the ID number with a small normal
driver, etc. (Initial ID value: 4)
ID switch
NOTE
- The ID number must not be unique in the SCSI chain. (Initial
setting: 4)
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the terminator on the rear of the printer to ON or OFF.
4
Terminator switch
The printer has the SCSI terminator ON/OFF function. If the external
terminator is not used and the printer is a terminating device in the SCSI
chain (only one SCSI connector is connected), set the terminator switch to
ON. If the printer is not a terminating device, set it to OFF.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
The power of the printer and the power of the heater are separated.
<Printer>
The printer has two power switches as follows.
(1) Printer switch
(2) Power ON/OFF switch
(1)
(2)
Printer front (Operation panel)
Printer rear (Left side)
Power receptacle
The printer is turned ON by turning the printer switch ON.
Afterward, turn the printer ON/OFF by the ON/OFF switch on the
operation panel.
NOTE
-
When the printer is connected with the computer, turn the
printer ON, and then turn the computer ON. To turn the
system OFF, turn the computer OFF, and then turn the
printer OFF.
-
Turn the computer ON after the printer becomes to the
online state.
<Heater>
The heater has two power switches as follows.
(1) Heater switch
(2) 100/200 V alternation switch
(1)
(2)
For Heater
100-120V 12A 50/60Hz
Power receptacle
Printer rear (Right side)
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On
<Printer>
Turn OFF (0) the printer switch on the left rear of the
1
printer, and plug one end of the supplied power cable into
the socket of the printer. Insert the other power plug of
the cable into an electrical outlet.
Printer switch
OFF (0)
Socket
Turn ON (1) the printer switch on the left rear of the
printer.
2
3
Printer switch
ON (1)
Socket
Turn ON the power ON/OFF switch on the operation panel.
Power ON/OFF
switch
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
When the switch is turned ON, a power-on self-diagnostic test is performed
and the following message appears on the LCD on the operation panel.
Booting
INITIALIZING
WAIT A MOMENT
PRINT READY
ROLL : 64” (PAPER)
If a 64" paper roll is used
The heater control panel is displayed by turning the printer power ON.
However, turn the heater power ON to use the heater.
When the heater power is turned OFF, the following message is displayed
on the heater control panel.
TURN ON
THE HEATER
NOTE
- Turn OFF the printer while “PRINT READY” is displayed on
the LCD panel except emergency.
Do not turn OFF the printer while “INITIALIZING” or
“CLEANING” is displayed on the LCD panel to avoid drop of
the ink and damage of the head.
- If the fan does not run or the operation panel lamp does not
light when the printer switch and power ON/OFF switch on
HINT
the operational panel are turned ON, the power supply may
be faulty.
- If an error is detected during the self-diagnostic test at
powering on, an error message appears on the LCD. See
the Section 5, Troubleshooting and take an appropriate
measure.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
<Heater>
Turn OFF the heater switch on the right rear of the
1
printer, and plug one end of the supplied power cable into
the socket of the printer. Insert the other power plug of
the cable into an electrical outlet.
Heater switch OFF (0)
100/200 V alternation switch
Power cable
Power socket
NOTE
- Do not use the other power cable than specified in this printer.
- Verify that the supplied power cable meets the local AC power
supply specifications.
- Verify that the 100 / 200 V alternation switch settings meets
the local AC power supply specifications.
Turn ON the heater switch on the right rear of the printer
to turn the heater ON.
2
Heater switch ON (1)
100/200 V alternation switch
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
Turning the Power Off
<Printer>
1
Turn OFF the power ON/OFF switch on the operation
panel for a couple of seconds.
SHUTDOWN
WAIT A MOMENT
The above message is displayed on the LCD to indicate that a
shutdown process is in progress. After the process ends, the power
is turned OFF.
If the power off state lasts for a short time, you may turn the power
off, skipping the fill cap operation by pressing the power ON/OFF
key while pressing the
key.
Performing the fill cap operation is recommended.
CAUTION
-
The printer switch on the rear of the printer should be used
only when the printer is turned OFF completely in order to
move it, connect it with a computer, install or maintain its
parts.
-
-
Turn the power ON/OFF switch OFF, wait for at least ten
seconds, then turn it ON again.
The printer performs fill cap operation to keep the good
head condition at first 20 hours after print wait state and
every 3 days.
It is recommended to keep the printer ON.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
<Heater>
1
The heater power is also turned OFF by turning OFF the
ON / OFF switch on the operation panel. Therefore, the
heater switch turning OFF operation is not necessary in
the normal use.
Heater switch
OFF (0)
NOTE
- Use the heater switch on the right rear of the printer only
when turning the printer OFF completely for transferring,
installing, and maintenance service of the printer.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
This section describes how to install a paper roll in the printer, and
remove it from the printer.
A paper roll is replaced in the following three cases:
- If a paper roll is replaced with another
- If it is replaced when it runs out
- If it is replaced when it jams
A paper replacement procedure in each case is explained below:
Installing Paper Roll in the Printer
Open the rear cover and slide the media edge guards to
the both edge of the platen.
1
NOTE
-
Set the media edge guard after completion of the paper
roll replacing. (See page 2-59, 60)
Insert the paper roll in the paper roll right flange (fix side).
2
Right flange (fixed)
Paper roll
NOTE
- Be sure not to damage the edge
of the paper roll when inserting
the paper roll in the flange.
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide the left flange (movable side) and put it into the
paper roll.
3
Left flange (movable)
Paper roll
CAUTION
Be sure not to catch
your finger in the rail of
the flange.
Tighten the left flange knob securely.
4
5
Pull the winder sensor lever to front side.
Left flange knob
Winder sensor lever
Lift the pressure roller up/down lever.
Pressure up/down lever
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Feed the paper until a buzzer sounds from the paper feeder.
6
Feed the paper until an edge of the paper goes out 200 mm or more from the
paper outlet.
(Paper setting direction)
<Outside rolling>
<Inside rolling>
Paper
Paper
Flange
Flange
NOTE
- Paper may stick to the paper feeder and is hard to set due to
operational condition especially low humidity. In such a case,
float paper from the paper feeder and set paper to the paper
feeder by holding both edges of the paper.
- Be sure not to hit the edge of the paper roll by the rear cover.
- Be sure that the media edge guard is not set under the paper.
(See page 2-52 Using the Media Edge Guard.)
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
7
When feeding a paper roll, hold it at the center and
rewind the flange to take up the slack in the paper.
The guide line on the printer is no more than a guide
line. Install paper roll on the printer in a straight line
against the paper roll.
The paper roll should not be inserted in the right of the perforated line.
If the paper roll is inserted in the right of the perforated line, adjust the
flange position.
Push down the pressure roller up/down lever.
8
9
Pressure up/down lever
Perform operations according to the guidance message shown on the LCD.
Confirm the media edge guard setting again.
Confirm whether the media edge guard does not goes down of the
paper.
CHECK EDGE GUARD
*OK?
Confirm the position of the media edge guard and press the
key.
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Select either paper roll or cut sheet.
10
SELECT PAPER
SELECT PAPER
ROLL/SHEET : BASE
SELECT PAPER
ROLL/SHEET : SHEET
ROLL/SHEET : ROLL
Select ROLL PAPER, CUT SHEET , or BASE with
or
key.
(See Page 2-45 "Using the Origin Point Setting Function" about "BASE")
Press the
Press the
key to change setting.
key to leave the setting as it is.
Select a paper type.
11
SELECT PAPERTYPE
PAPER : PAPER
SELECT PAPERTYPE
PAPER : XXX
Select paper type with
or
key.
Press the
Press the
key to change setting.
key to leave the setting as it is.
(When registering a new paper type)
SELECT PAPERTYPE
PAPER : PAPER
Select a paper type with
and
keys.
SELECT PAPERTYPE
(only registered paper types can be
selected.)
PAPER : TYPE01
SELECT PAPERTYPE
NEW PAPER ENTRY
•
Press
key to enter to NEW PAPER ENTRY menu.
•
Operation of the new paper entry is the same as operation for paper
entry from ENTRY menu. (See section 3, Entry Menu)
•
Press
key to return to SELECT PAPERTYPE menu.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
The paper will be set automatically.
12
13
PREPARING PAPER
WAIT A MOMENT
-
-
If it is ended normally, return to offline or online state.
If abnormal end occurs, an error message will be displayed.
Go back to 1.
Determine the position of movable fan.
After the paper setting operation finished, adjust the position of the fan
guard slide lever at the rear of the printer. (See "Using the fan guard slide
lever" (P.2-60).)
Fan guard slide lever
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Removing the Paper Roll from the Printer
Lift the pressure roller up/down lever.
1
Pressure roller up/down lever
Loose the left flange knob, pull out the paper roll from the
flange, and remove the paper roll from the printer.
2
Left flange
(2)
Paper roll
(3)
Right flange
(1)
(4)
Flange knob
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Paper Roll with Another
Put the printer offline. (Press the
key.)
1
INK
ENTRY
F•FDJ
PAPER
Press the
key and press the
key.
2
3
LIFT LEVER
Replace the paper according to the “Installing Paper Roll
in the Printer” and “Removing it from The Printer.”
Replacing Empty Paper Roll
A message appears on the LCD.
1
2
LIFT LEVER
SET PAPER
Replace the paper according to the “Installing Paper Roll
in the Printer” and “Removing it from the Printer.”
Replacing Jammed Paper Roll
See the Cleaning Paper Jam in Section 5, Troubleshooting.
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Installing/Removing Cut Sheet in/from the Printer
Install/Remove the cut sheet in/from the printer refering to the
procedures for the paper roll.
Cut sheet
Cut sheet
Guide line
Installing
Removing
NOTE
- When installing the cut sheet in the printer, set the cut sheet
using the guide line.
Paper Feed Adjustment Correction Value Setting
Set the paper of width larger than A1 size and length
1
longer than 1m. (Press the
key)
For the paper feed correction, obtain approximate paper feed adjustment
correction value in the ROUGH mode, and set exact correction value in the
DETAIL mode. One printing requires the paper length of 48 to 58 cm in the
ROUGH mode, or 27 to 32 cm in the DETAIL mode. (Printing of paper
feed adjustment pattern can be cancelled by pressing the
key.)
NOTE
- If you use the tension winding, be sure to set the paper feed
adjustment correction value in the tension winding mode.
- Longer print length is required in the tension winding mode.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the printer to OFFLINE mode.
2
3
(Press the
key)
INK
ENTRY
F•ADJ
PAPER
Press the
key, and then the
key to display a
paper feed adjustment pattern.
#FEED PATTERN
*ROUGH (NORMAL)
Select the print mode you usually use for the paper to which the paper feed
adjustment correction value is set.
Selectable print modes are Standard, High Quality, High Density, High
Speed, and Draft.
Select the paper feed adjustment pattern "Standard" if adjusting the high
speed mode.
Press the
,
key to select the ROUGH print
4
5
mode, and press the
key.
#FEED PATTERN
*OK?
If you press the
key, the paper feed adjustment
pattern "ROUGH" is printed.
The paper feed adjustment pattern "ROUGH" is printed in the selected print
mode.
#FEED PATTERN
*EXECUTING
From the printed result, select approximate paper feed
adjustment correction value.
6
As nine patterns are printed in steps of 0.25% in a range of 99.00% to
101.00%, select approximate correction value.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Press the
key, and then the
key to display
7
8
the entered correction value of paper feed adjustment.
#FEED ADJUST
*099.80%
Enter the paper feed adjustment correction value, and
press the
key.
Adjust the place with
key.
,
key and set a numeric value with
,
Press the
key, and then the
key to display
9
the paper feed adjustment pattern.
#FEED PATTERN
*ROUGH (NORMAL)
Press the
,
key to select a print mode for the
10
DETAIL pattern.
#FEED PATTERN
*DETAIL (NORMAL)
Select the same print mode as that for the ROUGH pattern.
Press the
key twice to print the paper feed
11
12
adjustment pattern "DETAIL".
#FEED PATTERN
*EXECUTING
From the printed result, select exact paper feed
adjustment correction value.
As five patterns are printed for the entered correction value in steps of
0.06% in a range of -0.12% to +0.12%, select appropriate correction value.
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the
key, and then the
key to display
13
14
15
16
the entered correction value of paper feed adjustment.
#FEED ADJUST
*099.80%
Enter the paper feed adjustment correction value, and
press the
key.
Adjust the place with
key.
,
key and set a numeric value with
,
Press the
key, and then the
key to display
the paper feed adjustment pattern.
#FEED PATTERN
>DETAIL (NORMAL)
Press the
key to return to the initial OFFLINE state.
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
How to identify paper feed adjustment pattern
Description is made in a case of black color.
If paper feed adjustment
correction value is large
If paper feed adjustment
correction value is appropriate
If paper feed adjustment
correction value is small
99.00%
100.25%
101.00%
Correction value is small
if the joints of pass lines
are overlapped (become
dark) on these
Correction value is
Correction value is large
if the joints of pass lines
are separated (become
light).
appropriate if the joints
of pass lines are not
overlapped but uniform.
horizontal lines.
NOTE
- Set average value if appropriate correction value is different
every head (every color). However, if an image to be printed
has a preferential color, set correction value of that color.
- Set average value if appropriate correction value is different
between left and right sides of the paper.
- Different appropriate correction value between left and right
sides of the paper may be caused by the skew. Check again
if the power is set correctly.
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
[Additional functions available from
V2.00 or later]
Change During Online Printing
During the online printing, the paper feed adjusting value can be
changed through the following operation.
PRINT READY
Idle status
ROLL : 64" (PAPER)
Data receiving start
Data LED flashing
PRINTING
ROLL : 64" (PAPER)
Press the
or
key
(Note: Disabled at the first scan and last scan)
FIN ADJ : 099. 80%
* 099.80%
Head print position adjustment
: 97.00% to 103.00%
- During "PRINTING" display, press the
or
key to display
currently selected paper feed adjusting value. On the right side of the
first row, the value at the start of print is displayed and it does not vary
until the print finished.
However, if a cleaning is executed in the MODE 2 in the midway of
operation, the changed value is displayed after the cleaning.
- With the
0.01%.
or
key, increase (or decrease) the value in a step of
- When the value is changed, it is reflected in the printing.
- Numerical values you changed are registered and remain unchanged.
- Original display is restored if no key is operated for 3 seconds.
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
Head Print Position Adjustment
(1)
Adjustment pattern print
Print the adjustment pattern print position of each head.
1
Select the OFFLINE mode. (Press the
key)
INK
ENTRY
F•ADJ
PAPER
2
3
Press the
key twice to display "ADJUST".
FUNK
SYSTEM
RESET
ADJUST
Press the
key and then the
key to display
"ADJUST PATTERN".
# ADJUST PATTERN
> TEST PRINT
4
5
Press the
press the
key and select "HEAD ADJ1", and then
key.
# ADJUST PATTERN
* HEAD ADJ 1
OK
If the
key is pressed, the "HEAD ADJ1" of
adjustment patterns is printed.
# ADJUST PATTERN
* EXECUTING
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Reciprocating position adjustment (R)
Reciprocating position adjustment (L)
Head position adjustment
Left and Right Head position
adjustment
Paper discharge
direction
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
(2)
Left and Right Head position adjustment
Adjusts the jetting position of nozzle.
Enter an adjustment value according to the head adjustment pattern.
1
Select "ADJUST", and then press the
"L/R ADJ".
key to display
# L/R ADJ Bk
> +00&A
2
3
Press the
press the
key to display the head to be adjusted, and
key.
# L/R ADJ Y
> +00&A
Of the left/right head position adjustment of the "HEAD
ADJ1" patterns, enter a numeric value of the fittest
pattern.
Select the digit to be entered between > and & with
,
keys, and change value with
,
keys.
Find a head adjustment sample where
2 lines with the same color are aligned.
In case of Y-head illustrated in the
right, for instance, -21 shows the
sample where both are not aligned; -8
shows the sample where both are
aligned. Accordingly, input -8 as an
appropriate adjustment value.
-8
-21
4
Press the
key.
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
(3)
Head position adjustment
Adjusts the head position for the scanning direction on a Bk head
basis.
Enter an adjustment value according to the head adjustment pattern.
1
Select "ADJUST", and then press the
"H-POS ADJ".
key to display
# H-POS ADJ Lm
> +00&A
2
3
Press the
press the
key to display the head to be adjusted, and
key.
# H-POS ADJ Lc
> +00&A
Of the main scan head position adjustment of the "HEAD
ADJ1" patterns, enter a numeric value of the fittest
pattern.
Select the digit to be entered between > and & with
keys, and change value with keys.
,
,
Find a head adjustment sample where
the BK head-line and the head-position
are aligned. In case of LC-head
illustrated in the right, for instance, -21
shows the sample where both are not
aligned; +2 shows the sample where
both are aligned. Accordingly, input + 2
as an appropriate adjustment value.
-21
+2
4
Press the
key.
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Paper Roll
(4)
Reciprocating position (Left) adjustment
Adjusts the head reciprocating position (Left).
Enter an adjustment value according to the head adjustment pattern.
1
Select "ADJUST", and then press the
"I-POS (L) ADJ".
key to display
# I-POS (L) ADJ Bk
> +00&A
2
3
Press the
press the
key to display the head to be adjusted, and
key.
# I-POS (L) ADJ Bk
> +00&A
Of the reciprocating print position (Left) adjustment of the
"HEAD ADJ1" patterns, enter a numeric value of the
fittest pattern.
Select the digit to be entered between > and & with
keys, and change value with keys.
,
,
For a hint on how to locate an appropriate adjustment value, refer
to (2) Head Right and Left Adjustment on page 2-27.
4
Press the
key.
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
(5)
Reciprocating print osition (Right) adjustment
Adjusts the head reciprocating position (Right).
Enter an adjustment value according to the head adjustment pattern.
1
Select "ADJUST", and then press the
"I-POS (R) ADJ".
key to display
# I-POS (R) ADJ Bk
> +00&A
2
3
Press the
press the
key to display the head to be adjusted, and
key.
# I-POS (R) ADJ M
> +00&A
Of the reciprocating head position (Right) adjustment of
the "HEAD ADJ1" patterns, enter a numeric value of the
fittest pattern.
Select the digit to be entered between > and & with
keys, and change value with keys.
,
,
For a hint on how to locate an appropriate adjustment value, refer
to (2) Head Right and Left Adjustment on page 2-27.
4
Press the
key.
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Ink Cartridges
This section describes how to replace an ink cartridge.
Ink cartridges should be replaced in the following two cases:
- If ink has run out
- If an ink cartridge is not installed
The ink cartridge replacement procedure in the following each case
is explained below.
NOTE
-
Do not remove an ink cartridge under the following
conditions.
Depending on the printer status, the ink spills within the
ink box, causing a trouble.
-
In case that no power is supplied to the printer because
of a power failure or printer breaker off.
-
In case that an error other than ink end has occurred.
-
-
If the cartridge in which the ink remains is replaced, do so
in the offline mode.
(=> "Section 3 Ink Menu (5)")
Make sure the upside and downside of the ink cartridge
before installing.
Ink Cartridge Replacement Procedure
Open the ink cover.
1
Ink cartridge
Push here to open/close the ink cover.
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove an ink cartridge from the printer.
2
Ink cover
Insert a new ink cartridge into the printer.
3
4
New ink cartridge
Ink cover
Close the ink cover.
Ink cover
End of ink cartridge replacement.
5
-
-
If it is ended normally, return to offline or online state.
If abnormal end occurs, an error message will be displayed.
Go back to 1.
-
The printer continues to print when the ink remains in the sub-tank
during replacing ink cartridge.
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Ink Cartridges
Replacing Empty Ink Cartridge
A guidance message appears.
1
OPEN L INKCOVER
CHANGE XX INK
XX: Ink name
Bk: BLACK
Lm: LIGHT MAGENTA
Lc: LIGHT CYAN
OPEN R INKCOVER
CHANGE XX INK
XX: Ink name
C: CYAN
M: MAGENTA
Y: YELLOW
Replace the ink cartridge according to the “Ink Cartridge
Replacement Procedure.”
2
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
If an Ink Cartridge Is Not Installed
The guidance message appears.
1
OPEN L INKCOVER
SET XX INK
XX: Ink name
Bk: BLACK
Lm: LIGHT MAGENTA
Lc: LIGHT CYAN
OPEN R INKCOVER
SET XX INK
XX: Ink name
C: CYAN
M: MAGENTA
Y: YELLOW
Replace the ink cartridge according to the “Ink Cartridge
Replacement Procedure.”
2
2-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Ink Cartridges
Replacing Cartridges during Printing
This unit enables you to replace the ink cartridges during the online
printing without interrupting the printing operation. Accordingly,
the guidance for ink replacement during the online printing is
displayed on the second line of LCD. The following describes the
guidance shown if the ink cover is opened during the online printing
or if the ink in main cartridge is used up.
<If the Ink Cover is Opened>
PRINTING
ROLL: 64 (PAPER)
XXXX:
L, R
PRINTING
INKCOVER IS OPEN
PRINTING
CLOSE X INKCOVER
The guidance that prompts you to close the ink cover is displayed
on the second line of LCD. The printing operation continues if the
ink is present in the sub tank even though the ink cover is open.
However, no ink is supplied to the sub tank because the ink cover
is open.
If the ink in the sub tank is used up, the print pause mode is activated
and the printing operation is interrupted until the ink cover is closed.
To recover from the interrupted state, close the ink cover and press
the ONLINE key, and the pause mode is then cancelled and the
print will restart.
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
<If the Ink in Main Cartridge is Used Up>
PRINTING
ROLL: 64 (PAPER)
XXXX: L, R
YY: Bk Lm Lc Y M C
PRINTING
OPEN X INKCOVER
PRINTING
CHANGE YY INK
The guidance that prompts you to replace the main cartridge is
displayed on the second line of LCD. The printing operation
continues until the ink in the sub tank is used up. During this time,
if you replace the cartridge, the printing operation can continue
without interrupting the printing operation.
If the main cartridge is not replaced even after the ink in the sub
tank was used up, the print pause mode is activated and the printing
operation is interrupted until the main cartridge is replaced.
To recover from the interrupted state, close the ink cover and press
the ONLINE key, and the pause mode is then cancelled and the
print will restart.
-
The guidance concerning the ink replacement during the
online printing is displayed on the second line of LCD,
same as the guidance mentioned above.
HINT
Respective recovery methods are same as usual trouble-
shooting methods.
2-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Ink Cartridges
If an Ink Cartridge Is Not Detected
The guidance message appears.
1
OPEN L INK COVER
CHECK XX INK
XX: Ink name
Bk: BLACK
Lm: LIGHT MAGENTA
Lc: LIGHT CYAN
OPEN R INKCOVER
CHECK XX INK
XX: Ink name
C: CYAN
M: MAGENTA
Y: YELLOW
Replace the ink cartridge according to the “Ink Cartridge
Replacement Procedure.”
2
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Waste Ink Bottle
This section describes how to replace a waste ink bottle.
The waste ink bottle should be replaced in the following two cases:
- If the waste ink bottle is full
- If the waste ink bottle is not installed
The waste ink bottle replacement procedures for these cases are
explained below.
NOTE
-
Do not replace the waste ink bottle during printing.
Waste Ink Bottle Replacement Procedure
Loosen the knob and lift up the lever from the waste ink
bottle.
1
Tube
(1)
Knob
(2)
Lever
(3)
Waste ink bottle
2
3
Wait for a while to drop the remaining ink into the ink tube.
Take out the filled waste ink bottle from the printer, and
securely cap the waste ink bottle to replace with a new
one.
2-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Waste Ink Bottle
4
5
Wipe up the spilt ink into the waste ink bottle unit.
Lift the lever and mount a new waste ink bottle.
6
Drop the lever and insert the ink tube securely and
tighten the knob.
(2)
(1)
7
8
The selection message of the waste ink counter setting
(reset (clear)) will be displayed.
#INK COUNT RESET
*NO
#INK COUNT RESET
*YES
Select “YES” and press the
key.
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Waste Ink Bottle Is Full
Replace the waste ink bottle according to the “Waste Ink
1
Bottle Replacement Procedure.”
NOTE
-
Make sure visually whether or not the waste ink bottle is
not full before using the printer.
The selection message of the waste ink counter setting
(reset (clear)) will be displayed.
2
#INK COUNT RESET
*NO
#INK COUNT RESET
*YES
NOTE
-
The waste ink counter is prepared for urging waste ink
disposal with the error message when the waste ink is more
than the specified amount by counting the used (waste)
ink amount.
The waste ink counter can detect full of the waste
simultaneously but cannot detect actual full state of the
waste ink.
The counter counts up from the empty of the waste ink
bottle. Always select “*YES” for the “INK COUTN RESET”
menu when replacing the waste ink bottle with a new one.
If not, the waste ink full counter cannot be only used
effectively, but also the waste ink becomes full before
generating warning and the waste ink may be spilt over.
Select “*YES” and press the
key.
3
2-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Waste Ink Bottle
If the Waste Ink Bottle Is Not Installed
A guidance message appears on the LCD.
1
2
3
BOTTLE ISN’T SET
SET BOTTLE
Insert a new waste ink bottle into the printer and install
the waste ink bottle cover.
⇒ See the step 3 of the Waste Ink Bottle Replacement
Procedure.
The selection message of the waste ink counter setting
(rest (clear)) will be displayed.
#INK COUNT RESET
*NO
#INK COUNT RESET
*YES
Select “*YES” and press the
key.
4
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Head Cleaning "CLEANING"
Put the printer offline. (Press the
key.)
1
INK
ENTRY
F•ADJ
PAPER
Press the
key to display the CLEANING menu.
2
INK
ENTRY
F•ADJ
PAPER
SERVICE
FEED
CLEANING
Press the
key to enter the head cleaning menu.
3
4
# CLEANING
>NORMAL
Press the
key.
# CLEANING
* OK?
5
Press the
option.
key and
key to select a cleaning
#CLEANING
*STRONG
#CLEANING
*SLIGHT
#CLEANING
*NORMAL
2-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Head Cleaning "CLEANING"
6
7
Press the
key.
#CLEANING
*BOTTLE OK?
Make sure that the waste ink bottle is not full, and then
press the
key again.
CLEANING
WAIT A MOMENT
XXX
XXX : Figure will be increased
in about 10 seconds.
NOTE
- The cleaning takes several minutes.
When the cleaning is completed, the screen is retured to
step 3 automatically.
8
9
# CLEANING
>NORMAL
Press the
key to return to the original offline mode.
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Feed "FEED"
This section describes how to manually feed paper after printing.
Put the printer offline. (Press the
key.)
1
INK
ENTRY
F•ADJ
PAPER
Press the
key to display the FEED menu.
2
3
SERVICE
FEED
CLEANING
Hold down the
key.
PAPER FEEDING
While the
key is kept pressed, the currently selected roll paper is fed.
If a cut sheet is used, it is discharged.
When the
key is released, paper feeding stops and
4
the top screen returns to offline mode.
SERVICE
FEED
CLEANING
2-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Feed "FEED"
Using the Origin Point Setting Function
<Origin Point Setting>
When printing a small size image such as a A4 size image on the
64-inch width paper, the large blank will be generated as the figure
shows below.
In this case, rewind the print paper and set the print origin point to
print an image on the blank area.
The print origin point setting at paper rewinding is called as “Origin
Point Setting Function.”
(1st time printing)
(Paper rewinding)
(2nd time printing)
Blank area
Origin point
Base point
<How to Use the Origin Point Setting Function>
1
Lift the pressure roller up/down lever and rewind the
paper.
SET PAPER
PUSH DOWN LEVER
Pressure roller up/down lever
NOTE
-
Rewind the paper after the paper is enoughly dried.
If not, the 1st time printing image may be damaged.
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Push down the pressure roller up/down lever.
2
Pressure roller up/down lever
Select “BASE” in the “SELECT PAPER” menu and press
the key.
3
SELECT PAPER
ROLL/SHEET: BASE
Input the paper width and press the
key.
4
5
The paper width detected at
previous time is displayed.
(Paper width input range: 290
to 1635 mm)
PAPER WIDTH
*1372 mm
Input the base point (print offset value for paper width
direction: origin point).
The base point set at previous
time is displayed.
BASE POINT
*0000 mm
The previous setting value will be displayed.
The origin moves if either paper width or base point is set.
Print margin
Base point input value
Paper width input value
2-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Feed "FEED"
Select “*Yes” or “No” of back feed operation.
6
PAPER FEED BACK
*NO
PAPER FEED BACK
*YES
The print dead area can be
decreased by rewinding the paper
for length between the paper output
sensor and grid roller.
The area from the paper output
sensor position to the print start
position (the grid roller) becomes
print dead area.
(20 to 30 mm from the front edge
cannot be printed.)
NOTE
-
Cut the edge of the paper so that it will be parallel to the
guide line before installing the paper.
If the edge of the paper is not parallel to the guide line, the
front side of the print is cut, the platen is stained with ink,
and the paper jam may be caused.
Select a paper type again.
7
SELECT PAPER TYPE
PAPER: TYPE01
PREPARING PAPER
WAIT A MOMENT
NOTE
-
When using the origin point setting function, keep front,
right, and left margins sufficiently because the paper is
rewinded manually.
-
-
The paper width and base point settings cannot be saved.
The origin point setting function can be used only for paper
roll. This function cannot be used for the cut sheet.
2-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Paper on Winder
A paper winder unit is built in the printer. It winds roll paper for
storage without cutting it.
Use the paper winder unit as follows:
Prepare the paper tube and 1 m-lead paper of which
paper width is the same as the paper’s you will use.
1
Attach the lead paper on the paper tube.
Tape
Paper tube
Approx. 1 m
Lead paper
NOTE
-
Pay attention to the direction of attaching tape on the
winding side according to the winding direction setting
(outer side rewind/inner side rewind).
-
-
Attach the paper to the take out roller straightly to protect
slanting feed.
The paper tube width on the winding side must be same
as the width of the rolled paper to be printed.
The use of larger width may cause a winding deviation.
Insert the paper tube with the lead paper to the left
flange.
2
Paper tube
Left flange
Left flange
Flange
Paper tube
Tension roller
2-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Paper on Winder
Slide the right flange (movable side) and insert it into the
paper tube.
3
Paper tube
Right flange
Left flange
Paper tube
Right flange
4
5
Tighten the right flange knob securely.
Paper tube
Right flange
Knob
Lift the pressure roller up/down lever, insert paper from
the paper feeder, push down the pressure roller up/down
lever to set the paper, and feed paper by the Feed menu
on the operation panel (see Section 3, Operation Panel
Menu Operations (Feed Menu)) until the paper is wound.
Paper feeder
Pressure roller up/down lever
Paper delivery unit (rear)
(1)
(2)
(3)
Pressure roller up/down lever
2-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape the edge of the paper on the lead paper at three
positions: both sides and center.
6
Paper
Tension roller
Lead paper
Tape
Tape
Paper tube
Manually turn the scroller flange in the direction of
winding to wind the paper slightly.
7
8
Tension roller
Right flange
Check the positions of the paper and winding sensor,
and install it.
Winder switch
Winding sensor
2-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Paper on Winder
The winding unit supports two winding methods; tension winding and
slack winding.
Generally, use the slack winding. If the slack winding does not work
correctly, use the tension winding. Also, be sure to use the slack winding
for glossy paper.
Also, inner winding and outer winding are available.
Tension roller setting.
•
•
Slack winding:
Set the tension roller to the upper side.
Tension roller
•
Tension winding: Set the tension roller to the lower side.
Tension roller
Slide seven tension rollers according to the paper width.
To slide a tension roller, loosen three slotted head screws.
2-51
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
-
Do not change the order of seven tension rollers, as their
outside diameters are different.
Changing the order will cause a skew.
Winding unit switch setting
•
Either internal winding or external winding can be selected.
When the winding unit is not used, turn the winding unit switch off.
Inner winding
Outer winding
Winding unit OFF
NOTE
-
-
-
Slacken the paper so that it passes inside the winding
sensor.
If the winding unit is not used, turn the winding unit switch
off.
When the paper roll for the winding unit nears the diameter
of the winding unit’s flange, remove the winding side paper
roll and replace the paper tube with a new one.
If not so, a winding error may occur.
In case that the paper roll for the winding unit
exceeds the diameter of the winding unit’s flange.
-
When printing without using a winding unit, edge of paper
or printing surface may be damaged or be folded due to
contact with the winding sensor caused by winds.
Fold the winding sensor, or handle the printing surface with
care.
2-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Heater Control Setting Temperature
Preset temperature
LCD
Current temperature
Rear Heater ON/OFF key
Front Heater ON/OFF key
Print Heater ON/OFF key
Front Heater UP/DOWN key
Rear Heater UP/DOWN key
Print Heater UP/DOWN key
In normal use, temperatures of all heaters for the every selected
media are preset automatically.
Therefore, ON/OFF setting and temperature setting for all heaters
are not necessary.
Use the heater control panel only when the fine adjustment for the
heater temperature is desired.
Set on/off and setup temperature of three heaters on the heater
control panel.
• ON/OFF setting: Use ON/OFF key for each heater.
• Temperature setting: Use the up key or down key for each heater.
• LCD screen: (When the heater is turned ON)
• Upper line: Preset temperature for each heater
• Lower line: Current temperature for each heater
(When the heater is turned OFF)
• Upper line: “OFF” for each heater
• Lower line: Current temperature for each heater
The preset temperature range is fixed to 15 °C to 55 °C.
2-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Heater preset temperature by medium
The heater preset temperature for medium is listed in the table.
Preset the heater temperature according to the media you use.
Recommended preset
temperature
Medium
Media Type
Print mode
FRONT
PRINT
REAR
Glossy vinyle
chrolide
4 path
bi-direction
Glossy
Matte
45° C
40° C
45° C
4 path
bi-direction
Mat vinyle chrolide
Banner
45° C
45° C
40° C
40° C
45° C
45° C
4 path
bi-direction
Banner
It is recommended that the front heater, the print heater and the rear
heater be set to lower than 50 °C, 45 °C and 50 °C, respectively.
When the print heater is set to higher than 45 °C, we recommend
setting the head motion mode to "HIGHLIGHT."
NOTE
-
When the print heater temperature is set to high, fixibility
of the ink is improved, but paper wrinkle or mat print may
be caused.
Adjust heater temperature according to the paper type and
environmental temperature.
-
-
When the print heater temperature is set to high, the printer
may print at low speed to ensure stable print quality .
Set the front/rear heater temperature higher 5 °C than the
print heater’s.
Bad temperature balance between the front/rear heater
and print heater may cause paper wrinkle.
2-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Heater Control Setting Temperature
Flow of heater temperature setting
(1) If the paper type is selected in setting the paper, the temperature initial
value of each heater set for that paper is set on the heater control panel.
- If the temperature initial value has been set, the heater turns on. (Heating
does not start yet.)
- If the temperature initial value is set to **, the heater turns off. (The set
temperature display on the heater control panel becomes OFF.)
(2) If the print data are sent from the host (PC), either of the following
operations is performed before the print starts.
A) If "Priority Setting (Heater)" set for the paper is "Data Priority"
- The temperature set with RIP (print data, job) overwrites the set
temperature on the heater control panel, and the heating starts. (The
heating does not start if the temperature set value is OFF.)
- If the temperature is not set with RIP (print data, job), the heating starts
with the set temperature on the heater control panel.
B) If "Priority Setting (Heater)" set for the paper is "Panel Priority"
- The temperature set with RIP is ignored and the heating starts with the
set temperature on the heater control panel.
(3) The print starts when the current temperature of front, print, and rear heaters
all reaches the value exceeding "set temperature -2 °C", the print starts.
If the current temperature is higher than the set temperature, the print starts
without waiting for the temperature to drop. Even after the print started, the
temperature control is made so that the heaters keep the set temperature.
(4) During the printing, the temperature can vary while the printing is
performed by changing the set temperature with the "TEMPERATURE
UP/DOWN" key on the heater control panel.
Even after the print finished, the temperature changed in this section
remains as "set temperature".
(5) Hence, the print job returns to step (2).
For the temperature initial value setting of front, print, and rear heaters, and
the priority setting (heater), see Section 3 Entry Menu.
-
The heaters operate under the condition displayed on the
heater control panel, whatever means are used to set
the temperature.
HINT
2-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Media Pressure Alternation Lever
Alternate the media gripping pressure of the paper transmission
roller according to the media.
Generally, set the media pressure alternation lever to “normal
pressure.” When media cannot be fed correctly due to skew, set
the media alternation lever to “high pressure.”
Use the media pressure alternation lever to alternate the media
gripping pressure (See the figure below) .
Normal pressure
High pressure
Paper pressure alternation lever
NOTE
-
The shape of the lever groove is shown below.
(2)
(1)
Pull the lever front and push up the lever for alternate the
pressure from high to normal.
2-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Head Up/Down Lever
Alternate the head height according to the media you use.
Use the head up/down lever for alternating the head height.
(See the figure below)
1
2
Enter SERVICE menu and execute HEAD HEIGHT ADJ
on the operation panel.
#ADJUST HEIGHT
>EXECUTING
#ADJUST HEIGHT
>
Open the cap cover and loosen the head fixing screws (2
pieces) with a screw driver.
Cap cover
Head fixing screw
3
Alternate the height of the head with the head up/down
lever.
Up (for thinner media (standard))
Down (for thicker media)
Head up/down lever
Generally, preset the head up/down lever up for glossy vinyle chloride and
matted vinyle chloride, and preset the head up/down for banner and FF.
When the paper thickness is 0.5 mm or more, preset the head up/down lever
up regardless of media type.
When the head is rubbed with the media due to media floating, preset the
head up/down lever down even for the thinner media.
2-57
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Tighten the head fixing screws (2 pieces).
NOTE
-
When changing the height of the head, tighten the head
fixing screws while pushing the head down softly with your
hand.
-
-
When the head height is changed, change head height
setting (19) in ENTER menu.
When the head height is changed, print gap may be
occurred at reciprocating print. In that case, adjust the
correction value for reciprocating print. (See (20)
Reciprocating print position (Left) adjustment value, and
(21) Reciprocating print position (Right) adjustment value
in ENTRY nemu.)
2-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Media Edge Guard
Mount the media edge guard on the right and left media transmission
path to protect the head from nap and curl of the media edge.
Media edge guards
Media
NOTE
-
Preset whether or not the edge guard exixts in the PAPER
menu on the operation panel corresponding to the mounting
the media edge guard.
The right and left margin of the print area will be changed
according to the setting of the edge guard.
When using the media edge guard, right and left margin of
the print area becomes 10 mm.
-
2-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the FAN Guard Slide Lever
Cut suction of the FAN for unused area to protect the head from
suction of the FAN.
Slide the FAN guard slide lever between 50 inch width and 64 inch
width.
Set the FAN guard slide lever according to the paper width you
use.
NOTE
-
-
-
When setting the FAN guard slide lever for 50 inch width
paper at 64 inch width paper printing, the paper cannot be
passed.
Do not move the fan guard slide lever during print.
If the fan guard slide lever hits the paper, paper jam could
be occurred.
To prevent a jam due to the skew feed, ensure a clearance
of about 5mm between the arrow on the slide lever and
the paper edge.
Paper
Slide lever
2-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Print Pause/Restart and Cancel Keys
Print pause/restart and print cancel are also available from the rear
(paper outlet side) of the printer.
Print pause/restart and print cancel are available during checking
the print condition from the paper outlet side.
(Rear)
PRINT Pause/Restart and Cancel Keys
Paper
ONLINE key
CANCEL key
ONLINE key: Pause/Restart printing
CANCEL key: Cancels printing
Operations of the ONLINE and CANCEL keys are the same as
those of the operation panel’s.
2-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
Regular inspection and maintenance by operators are described
below.
Regular inspection and maintenance guide
The printer needs regular inspection and maintenance.
The table below lists all regular inspection and maintenance.
For details of each regular inspection and maintenance, see the page
to be referred.
page to be
Categoly
Inspection/Maintenance
referred
2-63
- Wiper Blade Cleaning
- Wiper Sponge Cleaning
- Capping Unit Cleaning
- Waste Ink Bottle Disposal
- Soft Head Cleaning
- Test Print
1 Daily inspection and maintenance
Every one month inspection and
maintenance
2
- Head cleaning
2-67
2-67
When leaving the printer for a long
3 time in power off state (more than - Service Clean
2 weeks)
When returning the printer from a
- Head Wash
4
long time leaving (more than 2
weeks)
2-68
2-69
2-71
- Ink charge after head washing
When returning the printer from a
5 long time leaving (within 2 weeks)
in power off state.
- Head Wash
- Ink charge after head washing
A service call error message will
be displayed on the operation
panel. Contact our service center.
When leaving the printer in power
off for more than one month
6
2-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
Daily inspection and maintenance
Perform the followings every day to ensure stable print quality.
(1) Wiper Blade Cleaning
(2) Wiper Sponge Cleaning
(3) Capping Unit Cleaning
(4) Waste Ink Bottle Disposal
(5) Soft Head Cleaning
(6) Test Print
NOTE
-
-
Perform the above every day before print.
Always use our specified cleaning liquid and cleaning swab.
<Wiper Blade Cleaning>
Enter to the “SERVICE” menu and select “WIPE CLEANING” on
the operation panel.
#WIPER CLEANING
>
The wiper blade will come up for cleaning.
Open the rear cover and the wiper cover.
Rear cover
Wiper cover
2-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Check no dregs of the dried ink and no damage on the blades.
Clean the front and back of the blades with the cleaning swab infiltrated
into the wiper cleaning liquid.
After completion of the cleaning, close the wipe cover and the rear
cover to return the wiper to the position as it was.
Wiper blades
NOTE
-
Take extreme care not to allow the wiper cleaning liquid to
attach to the parts other than wiper blades.
Attaching the wiper cleaning liquid to the belts or sensors
may cause a trouble.
<Wiper Sponge Cleaning>
The wiper sponge has to be moistened.
Check the moisture of the sponge every day before printing.
Check whether the sponge is dried by pressing the dried swab on the
sponge.
If the sponge is dried, moisten it with the wiper cleaning liquid.
We recommend applying wiper cleaning liquid of one syringe to the
wiper sponge every day.
Wiper sponge
Syringe
2-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
NOTE
-
Take extreme care not to spill the wiper cleaning liquid on
the parts other than the wire sponge.
Spilling the wiper cleaning liquid on the belts or sensors
may cause a trouble.
<Capping Unit Cleaning>
Enter to the SERVICE menu and select “CAP CLEANING” on the
operation panel.
#CAP CLEANING
>
The head carriage will move to the wipe side and you can access easily
to the capping unit.
Open the rear cover and cap cover. Wipe up the edge and periphery of
the upper surface of all (six) caps carefully with the cleaning swab.
Clean he edge and periphery
of the upper surface of the
cap.
Close the cap cover and rear cover. The head carriage will return to the
capping unit position (home position) automatically.
NOTE
-
Do not leave the printer for long time in the condition that
the head carriage is not on the capping unit.
2-65
Download from Www.Somanuals.com. All Manuals Search And Download.
<Waste Ink Bottle Disposal>
Pour the waste ink into the proper container you prepared and make
the waste ink bottle empty.
<Soft Head Cleaning>
Enter to the “CLEANING” menu and select “SLIGHT” on the
operation panel. (See page 2-42.)
<Test Print>
Enter to the “ADJUST” menu and select “TEST PRINT” on the
operation panel. (See page 3-44.)
Check no print dot-off and missing.
Perform the test print as the 1st time print on every day and especially
after cap cleaning for head cleaning.
When the print dot-off occurs at test print, perform slight head cleaning
in the “CLEANING” menu. (See page 2-42.)
NOTE
-
Do not leave the head carriage at the position other than
on the capping unit for a long time (more than 5 minutes).
Perform the soft head cleaning after completion of the test
print.
-
2-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
Every one month inspection and maintenance
<Head Cleaning>
Clean the head one time per a month according to the documentation
attached to the head cleaner kit.
When leaving the printer for a long time (more than 2 weeks) in power
off state
Store the printer after cleaning the head and ink path with the
maintenance liquid and charging the maintenance liquid.
Six maintenance liquid cartridges and six dummy cartridges are
mandatory.
Prepare the storage kit (IP6-137).
Six maintenance liquid cartridges (IP6-107) and six dummy
cartridges (IP6-118) are packed together in the storage kit.
Six maintenance liquid cartridges are used up by one service clean.
<Servce Clean>
Enter to the “SERVICE” menu and select “ SERVICE CLEAN.”
#SERVICE
>SERVICE CLEAN
After the service clean finished, turn off the power with dummy
cartridges inserted and leave the printer as it is.
The head wash operation is mandatory when returning the printer from
the status that the service clean is performed.
2-67
Download from Www.Somanuals.com. All Manuals Search And Download.
When returning the printer from a long time leaving (more than 2 weeks)
Perform the cleaning of the head and ink path with cleaning liquid.
Six cleaning liquid cartridges and six dummy cartridges are
mandatory.
Prepare the cleaning kit (IP6-117).
Six cleaning liquid cartridges (IP6-119) and six dummy cartridges
(IP6-118) are packed together in the cleaning kit.
Six cleaning liquid cartridges are used up by one head wash.
<Head Wash>
Select HEAD WASH in SERVICE menu on the operation panel.
#SERVICE
>HEAD WASH
After performing the head wash, charge the ink (See Ink Charge after
Head Washing).
NOTE
-
The printer performs fill cap operation to keep the good
head condition at first 20 hours after print wait state and
every 3 days.
It is recommended to keep the printer ON except when the
printer is not used for a long time.
Avoid leaving the printer with no ink for one month or more
for head protection.
-
Do not open and close the rear cover and do not lift and
push down the levers during service cleaning and head
washing.
If doing so, the printer may start service cleaning and head
washing from the begining.
<Ink Charge After Head Washing>
Charge the ink after head washing before printing when the printer is
leaved for a long time.
Enter to “SERVICE” menu and select “INK CHARGE” on the
operation panel.
2-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
#SERVICE
>INK CHARGE
Insert the ink cassettes and charge the ink.
Leave the printer for at least one hour after completion of ink charging.
Check moisture of the wiper sponge.
Perform the test print.
When the print dot-off occurs during the test print, perform slight
cleaning in the “CLEANING” menu.
(See page 2-42.)
NOTE
-
The ink of about 200cc is used for the ink charge. If the
cartridge in which the remaining amount of ink is less than
200cc has been inserted, replace it with the cartridge that
contains the ink more than 200cc.
When returning the printer from a long time leaving (within 2 weeks) in
power off state.
<Head Wash>
Perform the cleaning of the head and ink path with cleaning liquid.
Six cleaning liquid cartridges and six dummy cartridges are mandatory.
Prepare the cleaning kit (IP6-117).
Six cleaning liquid cartridges (IP6-119) and six dummy cartridges (IP6-
118) are packed together in the cleaning kit.
Six cleaning liquid cartridges are used up by one head wash.
#SERVICE
>HEAD WASH
After performing the head wash, charge the ink (See Ink Charge After
Head Washing).
2-69
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
-
The printer performs fill cap operation to keep the good
head condition at first 20 hours after print wait state and
every 3 days.
It is recommended to keep the printer ON except when the
printer is not used for a long time.
Avoid leaving the printer with no ink for one month or more
for head protection.
-
Do not open and close the rear cover and do not lift and
push down the levers during service cleaning and head
washing.
If doing so, the printer may start service cleaning and head
washing from the begining.
<Ink Charge After Head Washing>
Charge the ink after head washing before printing when the printer is
leaved for a long time.
Enter to “SERVICE” menu and select “INK CHARGE” on the
operation panel.
#SERVICE
>INK CHARGE
Insert the ink cassettes and charge the ink.
Leave the printer for at least one hour after completion of ink charging.
Check moisture of the wiper sponge.
Perform the test print.
When the print dot-off occurs during the test print, perform slight
cleaning in the “CLEANING” menu.
(See page 2-42.)
NOTE
-
The ink of about 200cc is used for the ink charge. If the
cartridge in which the remaining amount of ink is less than
200cc has been inserted, replace it with the cartridge that
contains the ink more than 200cc.
2-70
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
When leaving the printer in power off for more than one month
Regardless of performing the service cleaning, a service call error
message will be displayed on the operation panel.
Contact SIIT service centers.
NOTE
-
Do not leave the printer without maintenance liquid charge
more than 2 weeks in power off state for head protection.
When leaving the printer more than one month, consult
with shops or our nearest service office in advance.
-
Cleaning outer case
If the outer case of printer was stained, wipe up stain with soft cloth
soaked in water or water downed neutral detergent and wringed well.
NOTE
-
-
Turn OFF the printer power switch before cleaning.
Do not use volatile solvent such as thinner and benzine to
prevent fade or detoriation of printing.
Cleaning rear cover and paper feed
Vacuum dust with a vacuum cleaner.
If stains are heavilly accumulated, wipe up them with soft cloth
soaked in the cleaning liquid.
Rear cover
Paper feed
NOTE
-
-
Turn OFF the printer power switch before cleaning.
Do not blow off paper dust.
If doing so, print quility gets bad influence.
2-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning platen
When glue adheres to platen or ink drops on the platen, clean the
platen according to the following procedures:
1
Open the rear cover and put a soft cloth on ink stained on
the platen to infiltrate ink into the soft cloth.
Infiltrate ink into the soft cloth with care so as not to spread it.
Soft cloth
Platen
Ink
2
Wipe out the ink mark on the platen with a soft cloth
moistened with alcohol.
Platen
Soft cloth moistened with alcohol.
2-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection & Maintenance
3
If ink gets into vacuum holes on the platen, wipe out ink
clung to the holes with a commerically-available mini-
cotton swab, then wipe out again with a mini-cotton swab
moistened with alcohol.
Use a ø3 mm mini-cotton swab.
Platen
Mini-cotton swab
2-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 Operation Panel
Menu Operations
This section outlines the user menu structure and operations.
Contents of This Section
Basic Menu Operation
Menu Hierarchical Structure
Menu Tree
Basic Operations and Keys
Operation Procedures for Choice Input, Value Input,
Execution and Character Input
Menu Operations
INK Menu
PAPER Menu
ENTRY Menu
F.ADJ Menu
SERVICE Menu
CLEANING Menu
FEED Menu
FUNC Menu
ADJUST Menu
SYSTEM Menu
RESET Menu
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
When the
key is pressed in the online idle mode, the printer
enters to the offline mode, a menu group appears on the LCD, and
menu operations are enabled.
INK
ENTRY
F.ADJ
PAPER
SERVICE
FEED
CLEANING
FUNC
SYSTEM
RESET
ADJUST
Menu Hierarchical Structure
The menu has the following hierarchical structures:
<Menu group>
This menu is displayed at the first level.
Some menus have several sub-menus.
<Second-level menus>
Sub-menus of the menu group
<Parameters>
Select a selected menu item or enter a value.
There are three methods: choice, value entry, and execution.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
Menu Tree
INK
ENTRY
F.ADJ
XX INK REST: YYY%
DATE : XX/XX/XX
Execution form
(Display)
PAPER
ROLL(XXXXXX)
Execution form
(Display)
SHEET(XXXXXX)
Execution form
(Display)
YYYYmmXZZZZmm
Execution form
(Display)
BASE(XXXXXX)
YYY
Enter a choice
01 to 20
#SELECT PAPER
>01 : TYPE01
#NAME
Enter characters
>01 : TYPE01
Enter a value
97.0 to 103.0
#FEED ADJUST
>01 : 099.80%
Enter a value
000 to 999
#SCAN WAIT TIME
>01 : 000sec
Enter a choice.
- NORMAL - DEWITY
#PRINT MODE
>01 : NORMAL
- FINE
- DRAFT
- FAST
Enter a choice.
- BI
- UNI
#DIRECTION
>01 : BI
Enter a choice.
- NONE - 2 hours
- 30 min - 4 hours
- 1 hour
#CONDITION PASS
>01 : NONE
Enter a choice
- USE
- NOT USE
#EDGE GUARD
>01 : USE
Enter a choice
- SEQUENCE 1
- SEQUENCE 2
#PAPER FEED MODE
>01 : SEQUENCE 1
Enter a choice
- SLACK
- TENSION
#WINDER MODE
>01 : SLACK
(1)
(2)
(3)
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
(3)
Enter a choice
- NORMAL
- SAVING
#PAPER SET MODE
>01 : NORMAL
Enter a choice
- NORMAL
- LOW
#VACUUM
>01 : NORMAL
Enter a choice
- WAIT
- SKIP
#WAIT HEATER
>01 : WAIT
#FRONT HEATER
>01 : 30C
Enter a value
15 to 55
#PRINT HEATER
>01 : 40C
Enter a value
15 to 55
Enter a value
15 to 55
#REAR HEATER
>01 : 50C
Enter a choice
- OFF
- ON
#COLOR STRIPE
>01 : OFF
Enter a choice
- NORMAL
- HIGHLIGHT
#HEAD MOTION
>01 : NORMAL
Enter a choice
- NORMAL
- HIGH
#HEAD HEIGHT
>01 : NORMAL
Enter a value
-32 to +31, a to H
YY: Bk, Lm, Lc, Y, M, C
#I-POS (L) ADJ YY
>01 : +00&A
Enter a value
-32 to +31, a to H
YY: Bk, Lm, Lc, Y, M, C
#I-POS (R) ADJ YY
>01 : +00&A
Enter a choice
- MODE 1
# CLEANING MODE
>01: MODE 1
- MODE 2
Enter a value
±2000
# BACK ADJUST
>01: +0000 PULSE
(4)
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
(1)
(2)
(4)
Enter a choice
- DATA
- PANEL
#PRIORITY FEED
>01 : DATA
Enter a choice
- DATA
- PANEL
#PRIORITY MODE
>01 : DATA
Enter a choice
- DATA
- PANEL
#PRIORITY HETER
>01 : DATA
Enter a value
01 to 20
#DLETE PAPER
>02 : TYOE02 OK?
Enter a value
01 to 20
#COPY SOURCE
>01
Enter a value
01 to 20
#COPY DEST
>01→01✽
Enter a choice
# FEED PATTERN
>ROUGH (NORMAL)
- ROUGH (NORMAL)
- ROUGH (H-QUAL)
- ROUGH (H-DENS)
- ROUGH (DRAFT)
- DETAIL (NORMAL)
- DETAIL (H-QUAL)
- DETAIL (H-DENS)
- DETAIL (DRAFT)
Enter a value
97.0 to 103.0%
#FEED ADJUST
>099.80%
Enter a choice
- NORMAL
- H-DENSITY
- H-QUALITY
- DRAFT
# BACK PATTERN
>NORMAL
Enter a value
±2000
# BACK ADJUST
>+0000 PULSE
Enter a choice
- SERVICE CLEAN
- HEAD WASH
- INK CHARGE
- INK EXTRACT
#SERVICE
SERVICE
FEED
>SERVICE CLEAN
CLEANING
#CAP CLEANING
>
Execution form
#WIPER CLEANING
>
Execution form
#FILL CAP
>
Execution form
Execution form
# ADJUST HEIGHT
>
(5)
(6)
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
(5)
(6)
Enter a choice
- NORMAL
- SAVING
#WASTE INK SAVING
>NORMAL
Enter a choice
- NORMAL
- SLIGHT
#CLEANING
>NORMAL
- STRONG
#FEEDING
Execution form
FUNC
SYSTEM
RESET
#MENU PRINT
>
Execution form
ADJUST
#ERROR LOG PRINT
>
Execution form
Execution form
Execution form
#TRACE PRINT
>01 : SEQUENCE 1
#HISTORY PRINT
>
Enter a choice
- TEST PRINT - HEAD ADJ1
#ADJUST PATTERN
>TEST PRINT
- HEAD ADJ2
- HEAD ADJ1-1
- HEAD ADJ1-2 - HEAD ADJ1-3
- HEAD ADJ2-1 - HEAD ADJ2-2
Enter a value
-32 to +31, A to H
YY: Bk, Lm, Lc, Y, M, C
# L / R ADJ YY
>+00&A
Enter a value
-32 to +31, A to H
YY: Bk, Lm, Lc, Y, M, C
# H-POS ADJ YY
>+00&A
Enter a value
-32 to +31, A to H
YY: Bk, Lm, Lc, Y, M, C
# I-POS (L) ADJ YY
>+00&A
Enter a value
-32 to +31, A to H
YY: Bk, Lm, Lc, Y, M, C
# I-POS (R) ADJ YY
>+00&A
Enter a choice
- JAPANESE
- ENGLISH
#LANGUAGER
>JAPANESE
#BOOT VERSION
*X.XX
Execution form
(Display)
#F/W VERSION
*X.XX_YY
Execution form
(Display)
(7)
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
(7)
#IPB VERSION
Execution form
(Display)
*X.X
#WIM VERSION
*X.X
Execution form
(Display)
#IPB VERSION
*X.X
Execution form
(Display)
#ASIC VERSION
*X.XX
Execution form
(Display)
#HEAT HW VERSION
*XX.X
Execution form
(Display)
#HEAT FW VERSION
*XX.X
Execution form
(Display)
#SCSI ID
*ID : X
Execution form
(Display)
Enter a value
00/01/01 to 99/12/31
#DATE(YY/MM/DD)
>03 / 08 / 01
Enter a value
00 : 00 to 23 : 59
#SYSTEM TIME
>00 : 00
#INITIAL SET
>
Execution form
Execution form
INITIALIZING
WAIT A MOMENT
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations and Keys
(1) To enable menu operations:
- Enter to the offline mode.
- When the printer enters the offline mode, a menu group screen is
displayed.
(2) Menu group selection:
- Select a menu group directly with
,
,
and
keys.
- Switch between menu group screens with the
key.
(3) Menu selection:
-
,
keys : Change between menus at the same level.
: Return to menu group selection.
-
-
key
key
: Select a menu so that parameters can be
changed.
(4) Parameter setting or change:
-
,
keys : Switch between parameters.
Increment or decrement a value when it is
entered.
-
,
keys : Shift digit when entering a value.
(5) Parameter setting or canceling:
-
-
key
key
: Set a parameter.
: Cancel an input parameter value and return to
the menu selection.
(6) Setting save:
- The changes in the Setup menu, System menu, and Mechanical
Adj. menu are automatically saved in parameters.
(7) End of setting:
- When the
online mode.
key is pressed, the printer goes back to the
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
Operation Procedure for Choice Input, Value Input, Execution, and Character Input
If a choice is input for a parameter:
An example of PRINT MODE of the ENTRY menu is given below.
(1) Select a menu group with
,
,
,
keys.
Select ENTRY menu with
key.
INK
ENTRY
F.ADJ
PAPER
(2) Select a sub-menu of the ENTRY menu with
and
keys.
Select PRINT MODE .
You can return to (1) with
key.
# PRINT MODE
> 01 : NORMAL
(3) Press
key so that parameters can be changed.
# PRINT MODE
* 01 : NORMAL
(4) Select a parameter for the menu with
and
keys.
Select 01 : FINE.
# PRINT MODE
* 01 : FINE
(5) Press
key to change the parameter and return to (2).
# PRINT MODE
> 01 : FINE
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
If a value is input for a parameter:
The PAPER FEED ADJ menu of the ADJUST menu is given as an
example.
(1) Select a menu group with
,
,
,
keys.
Select menu with
key.
FUNC
SYSTEM
RESET
ADJUST
(2) Select a sub-menu of the ADJUST menu with
and
keys.
Select PAPER FEED ADJ. menu.
You can return to (1) with
key.
# PAPER FEED ADJ
> 099. 80%
(3) Press
key so that parameters can be changed.
# PAPER FEED ADJ
* 099. 80%
(4) Move to a digit to be modified with
and
keys.
# PAPER FEED ADJ
* 099. 80%
(5) Modify the value by pressing the
and
keys.
# PAPER FEED ADJ
* 099. 70%
(6) Press
key to change the parameter and return to (2).
# PAPER FEED ADJ
> 099. 70%
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
If a parameter is executed:
Case 1: To print
The MENU PRINT menu of the FUNC menu is given as an
example.
(1) Select a menu group with
,
,
,
keys.
Select FUNC menu with
key.
FUNC
SYSTEM
RESET
ADJUST
(2) Select a sub-menu of the FUNC menu with
and
keys.
Select MENU PRINT menu.
You can return to (1) with
key.
# MENU PRINT
>
(3) Press
key.
# MENU PRINT
> OK ?
(4) Press
key to execute the function.
Press
key to return to (2) without executing the function.
# MENU PRINT
* EXECUTING
(5) After execution, return to (2).
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Case 2: To display only
The SCSI ID menu of the SYSTEM menu is given as an example.
(1) Select a menu group with
,
,
,
keys.
Select SYSTEM menu with
key.
FUNC
SYSTEM
RESET
ADJUST
(2) Select a sub-menu of the SYSTEM menu with
and
keys.
When the SCSI ID is selected, it is displayed.
# SCSI ID
*x: SCSI ID number
* ID : x
(3) Another sub-menu of the SYSTEM menu can be selected with
keys.
and
You can return to (1) with
key.
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Menu Operation
If a value is character input for a parameter:
An example of NAME of the ENTRY menu is given below.
(1)
Select a menu group with
,
,
,
keys.
Select ENTRY menu with
key.
INK
ENTRY
F.ADJ
PAPER
(2)
Select a sub-menu of the ENTRY menu with
and
keys.
Select NAME.
# NAME
>01 : TYPE01
(3)
Press
keys so that parameter can be changed.
#NAME
*01 : TYPE01
(4)
Select a character code group by pressing the
or and keys.
and
keys
Modify the value by pressing the
or
key.
(See “Character List” in the next page. )
# NAME
*01 : CYPE01
(5)
Move to a digit by pressing the
and
keys.
Then, modify the value.
#NAME
*01 : CYPE01
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
(6)
Press
key to determine the parameter.
# C_PAPER NAME
>01 : CYPE01
*
<Character List>
Character
Character code group
key
key
Symbols
space, !, • • • •
0 to 9
Backward
+
Numerals
(
key)
Alphabet • Capital letter
Alphabet • Small letter
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Katakana: line
Small letter katakana
Special characters
A toZ
a to z
Forward
+
(
key)
a, ä, b, • • • •
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
INK Menu
This menu is used to display ink information or replace the ink.
When the key is pressed, information on each color ink is
displayed at three-second intervals.
INK
ENTRY
F.ADJ
PAPER
XX: Color name, such as Bk,
Lm, Lc, Y, M, and C.
XX INK REST : YYY%
DATE : ZZ/ZZ/ZZ
YYY: Remaining amount of ink.
ZZ: Date
(1) XX INK indicates a remaining amount of ink.
DATE indicates the manufacture date of the ink cartridge.
(2) When the
key is pressed, you can go to the next step
without waiting for three seconds.
(3) When the
or
keys is pressed, display scrolling ends
and the top menu is displayed in offline state.
(4) When the
key is pressed, display scrolling ends and the
printer is put online.
(5) When the
key is pressed, display scrolling ends and the
printer enters recovery state (ink cartridge replacement).
(See Section 2, Replacing Ink Cartridge.)
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
PAPER Menu
This menu is used to display media information or replace the paper.
When the key is pressed, information on media is displayed at
three-second intervals.
INK
ENTRY
F.ADJ
PAPER
Key
<Paper roll>
ROLL(XXXXXX)
YYY
X: Paper type
Y: Paper size
<Cut sheet>
X: Paper type
SHEET(XXXXXX)
Y: Paper width (mm)
Z: Paper length (mm)
YYYYmm x ZZZMM
<Base>
X: Paper type
Y: Paper size
BASE(XXXXXX)
YYY
(1) When the
ends and the top menu is displayed in offline state.
(2) When the key is pressed, display scrolling ends and the
printer moves online state.
(3) When the key is pressed, display scrolling ends and the
and
keys are pressed, display scrolling
printer enters paper setting sequence.
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
ENTRY Menu
This menu is used to set up parameters for drawings.
When the key is pressed, parameters can be set.
PAPER
PAPER
ENTRY
F.ADJ
Key
#SELECT PAPER
>01 : TYPE01
(1) Paper selection (SELECT PAPER)
Select a paper type number to be registered newly or revised.
Twenty types (from 01 to 20) can be selected.
#SELECT PAPER
>01 : TYPE01
<Parameter (Enter a choice.)>
Paper type number: 01 to 20
(2) Paper name setting (NAME)
Set the paper name.
Six-digit characters (or symbols) can be input as the paper name.
Symbols, alphanumerals, katakanas can be used for six-digit
characters.
#NAME
>01 : TYPE01
<Parameter (Enter characters)>
A six-digit character (symbols, alphanumerals, katakanas, others)
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) Paper feed adjustment value (FEED ADJUST) (Unit: %)
Set a paper feed adjustment value.
BASE=099.92%
>01 : 099.80%
FEED ADJUST
>01 : 099.80%
<Parameter (Enter a value)>
XXX.XX% (97.00 to 103.00%)
(4) Scan waiting time (SCAN WAIT TIME) (Unit: second)
Set the paper scanning wait time.
SCAN WAIT TIME
>01 : 000sec
<Parameter (Enter a value)>
Input three-digit in second unit.
(5) Print mode setting (PRINT MODE)
Set a print mode.
PRINT MODE
NORMAL
<Parameter (Enter a choice)>
NORMAL: (4-pass)
FINE: (8-pass)
DENSITY: (8-pass)
FAST: (4-pass)
DRAFT: (2-pass)
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(6) Print direction setting (DIRECTION)
Set a print direction.
#DIRECTION
>01 : BI
<Parameter (Enter a choice)>
BI: Print with dual direction.
UNI: Print with single direction.
(7) Condition pass setting (CONDITION PASS)
Selects a conditioning pass mode for the paper.
When the print waiting condition continues for a long time, the
faint print or print off may be caused by the wrinkle or smudge on
the edge of the paper roll due to humidity and dust.
Use this function to avoid these problems.
Set parameters according to the operational condition.
If there is no received data and the printer waits printing even though
the specified time has passed, the edge of the paper roll is fed to the
front of the rear cover automatically.
(If the edge of the paper roll exists in the front of the rear cover
already, this action will be skipped.)
When the print data is received and print starts, the conditioning
pass (the repetition of paper feeding and rewinding) is performed
automatically.
Also, when the printer is turned off, the edge of the paper roll is fed
to the front of the rear cover automatically before turning off. (When
using the winder, the printer is turned off immediately.)
#CONDITION PASS
>01 : NONE
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
<Parameter (Enter a choice)>
- NONE:
The conditioning pass is not performed.
Select this parameter when performing the continuous printing
with the media that is hard to be wrinkled.
When the printer is left in the waiting condition for a long time,
the print off due to wrinkles may be caused.
- 30 min:
The conditioning pass is performed at every 30 minutes.
When the printer starts printing before 30 minutes interval, the
condition pass is always performed at start of the printing.
Select this parameter when the printer prints in a high humidity
environment frequently and the paper is extremely wrinkled.
- 1 hour:
The conditioning pass is performed at every 1 hour.
Select this parameter when the print interval is more than 1
hour and the paper is extremely wrinkled.
- 2 hours:
The conditioning pass is performed at every 2 hours.
Select this parameter when the print interval is more than 2
hours and the paper is extremely wrinkled.
- 4 hours:
The conditioning pass is performed at every 4 hours.
Select this parameter when the print interval is more than 4
hours and the paper is extremely wrinkled.
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(8) Edge guard setting (EDGE GUARD)
Set whether the media edge guard is used or not.
The right and left print margins will be changed by this setting.
#EDGE GUARD
>01 : USE
<Parameter (Enter a choice)>
-
-
USE
: Set when the edge guard is used.
NOT USE : Set when the edge guard is not used.
(9) Paper feed mode setting (PAPER FEED MODE)
Set a paper feed mode.
#PAPER FEED MODE
>01 : SEQUENCE 1
<Parameter (Enter a choice)>
-
SEQUENCE 1
: Feeds the paper in the normal paper feed
sequence.
-
SEQUENCE 2
: Feeds the paper in the counter measure
sequence for paper with glue.
(10) Winder mode (WINDER MODE)
Set a paper winding mode.
#WINDER MODE
>01 : SLACK
<Parameter (Enter a choice)>
-
SLACK
: Drives the winder with the SLACK rewinding
method.
-
TENSION : Drives the winder with the TENSION rewinding
method.
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
(11) Paper setting mode (PAPER SET MODE)
Detects the edge of the paper when replacing or setting the paper,
and selects whether the paper should be returned to the waiting
position.
When the winder is effective, the paper will not be returned to the
waiting position regardless of this setting.
#PAPER SET MODE
>01 : NORMAL
<Parameter (Enter a choice)>
-
NORMAL :Detects the paper width when replacing or setting
the paper, and then completes the paper setting after
checking paper skew during paper feeding.
SAVING: Detects the paper width at replacing or setting the
paper and then completes the paper setting after
detecting the edge of the paper during paper
rewinding.
-
NOTE
Usually set "NORMAL" when selecting "SAVING," take care
of the followings.
- Cut the edge of the paper so that the edge of the paper is
parallel to the guide line and set it to the printer.
If the edge of the paper is not parallel, the print is missed on
the edge of the paper and the platen is stained by ink and
the paper jam is caused.
- Set the paper after checking no wrinkle on the edge of the
paper.
If using the paper with a wrinkle, it causes paper jam.
- Set the paper after checking no tape or glue or the edge of
the paper. If using the paper with tape or glue, it causes
paper jam.
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(12) Wind value setting for FAN (VACUUM)
Sets wind value for FAN.
#VACUUM
>01 : NORMAL
<Parameter (Enter a choice)>
-
-
NORMAL: Absorbs the paper at the normal wind value.
LOW: Absorbs the paper at the low wind value.
(13) Wait of heating setting (WAIT HEATER)
Sets whether print should wait for time that the heater temperature
reaches the preset temperature.
#WAIT HEATER
>01 : WAIT
<Parameter (Enter a choice)>
- WAIT:
Waits the time until the heater temperature reaches
the preset temperature.
- SKIP:
Starts printing even if the heater temperature does
not reach the preset temperature.
(14) Initial temperature setting for the front heater (FRONT HEATER)
Sets the front heater temperature.
(Celsius)
(Fahrenheit)
#FRONT HEATER
>01 : 30C
#FRONT HEATER
>01 : 086F
<Parameter (Enter a value)>
Range: 15 °C to 55 °C
(The heater will be OFF when "**" is set.)
-
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
(15) Initial temperature setting for the print heater (PRINT HEATER)
Sets the platen heater temperature.
(Celsius)
(Fahrenheiht)
#PRINT HEATER
>01 : 40C
#PRINT HEATER
>01 : 104F
<Parameter (Enter a value)>
- Range: 15 °C to 55 °C
(The heater will be OFF when "**" is set.)
(16) Initial temperature setting for the rear heater (REAR HEATER)
Sets the rear heater temperature.
(Celsius)
(Fahrenheiht)
#REAR HEATER
>01 : 50C
#REAR HEATER
>01 : 122F
<Parameter (Enter a value)>
- Range: 15 °C to 55 °C
(The heater will be OFF when "**" is set.)
Celsius or Fahrenheiht display will be alternated on the heater panel.
The setting will be reflected at next powering on.
Celsius and Fahrenheiht conversion equation.
F=(9/5) C+ 32
HINT
C=(5/9) (F-32)
(17) Color stripe setting (COLOR STRIPE)
Sets ON/OFF of the color stripe print.
#COLOR STRIPE
>01 : OFF
<Parameter (Enter a choice)>
- OFF: Does not print the color stripe at the origin point.
- ON: Prints the color stripe print at the origin point.
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
NOTE
If the color stripe is not set, the print dot-off may occur.
It is recommended to set the color stripe for printing, if
practicable.
*The color stripe is printed on the test print regardless of this setting.
(18) Head action mode setting (HEAD MOTION)
Selects a head action mode.
#HEAD MOTION
>01 : NORMAL
<Parameter (Enter a choice)>
- NORMAL:
Use this usually.
Use this for print gradation data.
- HIGHLIGHT:
NOTE
If a pattern having very low printing rate in even one color is
printed continuously at high temperature, the print dot-off may
occur in low printing rate color. In this case, set the head
mode to HILIGHT PRIORITY.
(19) Head height setting (HEAD HEIGHT)
Selects a head height setting. This setting will be matched to the
head height lever setting.
#HEAD HEIGHT
>01 : NORMAL
<Parameter (Enter a choice)>
- NORMAL: Use this usually.
- HIGH:
Use this for thick media.
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
(20) Reciprocating print position (Left) adjustment (Bk/Lm/Lc/Y/M/C)
Adjusts reciprocating print positions (Left) for all heads. (I-POS
ADJ YY)
Enter an adjustment value based on the head adjustment pattern print.
#I-POS (L) ADJ YY
YY: Ink color
>01 : +00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
(21) Reciprocating print position (Right) adjustment (Bk/Lm/Lc/Y/M/C)
Adjusts reciprocating print positions (Right) for all heads. (I-POS
ADJ YY)
Enter an adjustment value based on the head adjustment pattern print.
#I-POS (R) ADJ YY
YY: Ink color
>01 : +00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
(22) Cleaning mode
Selects a cleaning mode to be performed automatically daring print.
# CLEANING MODE
>01: MODE 1
<Parameter (Enter a value)>
MODE 1: Performs cleaning automatically according to the
print history record at start of the print or at end of
the print.
MODE 2: Performs cleaning automatically in a certain period
during print.
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
NOTE
- When the tension winding as the winding mode or sequence
2 as the paper feed mode is selected, the printer works at
mode 1 setting even if the mode 2 is selected.
- When selecting mode 2, a joint of print will be generated
because the cleaning is performed during print.
A joint can be adjusted with correction value input at "BACK
ADJUS" menu.
In case a joint cannot be adjusted, use mode 1.
(23) Paper back feed adjustment (unit: pulse)
Adjusts a joint position when the image is separated due to the
automatic cleaning during print.
Input a back feed adjustment value for the paper.
# BACK ADJUST
>01: +0000 PULSE
<Parameter (Enter a value)>
-
-
±2000 pulses (+5 mm)
1 pulses=2.5 µm
(24) Paper feed adjustment value priority setting (PRIORITY FEED)
Selects a priority of the paper feed adjustment value.
#PRIORITY FEED
>01 : DATA
<Parameter (Enter a value)>
- DATA:
Gives priority to data.
- PANEL:
Gives priority to the panel.
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
(25) Print mode priority setting (PRIORITY MODE)
Selects a priority of the print mode.
#PRIORITY MODE
>01 : DATA
<Parameter (Enter a value)>
-
-
DATA:
Gives priority to data.
PANEL: Gives priority to the panel.
(26) Heater mode priority setting (PRIORITY HEATER)
Selects a priority of the heater mode.
#PRIORITY HEATER
>01 : DATA
<Parameter (Enter a value)>
- DATA:
Gives priority to data.
- PANEL:
Gives priority to the panel.
(27) Deleting registrated paper (DELETE PAPER)
Deletes a registrated paper.
The registrated paper from 01 to 20 can be selected.
The registrated paper 01 is defined as the standard media. This
cannot be deleted.
When the
key is pressed, confirmation guidance will be
displayed (See below.)
#DELETE PAPER
>01 : TYPE02
#DELETE PAPER
>01 : TYPE02 OK?
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(28) Copy source and copy destination
[Additional functions available from V2.00 or later]
Select the copy source and copy destination to copy the media
information.
Parameters to be copied refer to each setting of (2) through (26) in
the ENTRY menu.
1) COPY SOURCE
Select a copy source of the media entry number.
This function copies already registered media information to copy
the parameters in a set of the COPY DEST in 2).
For further information, see the description of parameter copy
method.
# COPY SOURCE
> 01
<Parameter (choice input)>
Paper No.: 01 - 20 However, only the registered numbers are
displayed.
2) COPY DEST
Select a copy destination for media registration.
# COPY DEST
> 01→01*
<Parameter (choice input)>
Paper No.: 01 - 20 The number already registered is attached
with * (asterisk).
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
<Description of parameter copy method>
The following explains how to copy the parameter registered to
paper No. 13 to paper No. 20.
1) Select a copy source
# COPY SOURCE
> 01
Key
The parameter can be changed
with the
(For the copy source number,
only the registered numbers are
displayed)
,
key.
# COPY SOURCE
* 01
,
Key
Press the key to determine
the copy source parameter.
# COPY SOURCE
* 13
Key
# COPY SOURCE
> 13
NOTE
- If the
key is pressed in the midway of each menu
operation, the first menu comes back.
3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
2) Select a copy destination
A numeral on the left side is the
copy source number.
# COPY DEST
> 13→01 *
Key
The parameter can be changed
with the
,
key.
# COPY DEST
(For the copy destination
number, 01 - 20 are displayed)
If the copy destination has
already been registered, * is
displayed following a numeral.
* 13→01 *
,
Key
Press the
key to determine
# COPY DEST
the copy destination parameter.
If the copy destination is newly
registered, * is not displayed
following a numeral.
* 13→20
Key
Key
Press the key to execute
the parameter copy operation.
# COPY DEST
* 13→20 OK?
# COPY DEST
* 13→20 *
NOTE
- If the
key is pressed in the midway of each menu
operation, the first menu comes back.
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial values for the registered papers
Some papers will be registered at shipping.
(The parameters registered at shipping are changeable and deletable.
However, 01 (PAPER) cannot be deleted.)
The table lists the initial values for the papers registered.
1
2
3
4
5
NAME
PAPER
Glossy
Matte
Banner
BLT_B
FEED ADJUST
SCAN WAIT TIME
PRINT MODE
DIRECTION
(Base) +0.00% (Base) +0.16% (Base) +0.16% (Base) +0.14% (Base) +0.14%
0 sec
NORMAL
BI
0 sec
NORMAL
BI
0 sec
NORMAL
BI
0 sec
NORMAL
BI
0 sec
NORMAL
BI
CONDITION PASS
EDGE GUARD
None
None
None
None
None
USE
USE
USE
USE
USE
PAPER FEED MODE SEQUENCE1 SEQUENCE1 SEQUENCE1 SEQUENCE1 SEQUENCE1
WINDER MODE
PAPER SET MODE
VACUUM
SLACK
NORMAL
NORMAL
WAIT
None
SLACK
NORMAL
NORMAL
WAIT
45° C
SLACK
NORMAL
NORMAL
WAIT
45° C
SLACK
NORMAL
NORMAL
WAIT
45° C
SLACK
NORMAL
NORMAL
WAIT
45° C
WAIT HEATER
FRONT HEATER
PRINT HEATER
REAR HEATER
COLOR STRIPE
IPOS (L) ADJ
None
40° C
40° C
40° C
40° C
None
45° C
45° C
45° C
45° C
ON
ON
ON
ON
ON
+00&A
+00&A
MODE 1
0
+00&A
+00&A
MODE 1
0
+00&A
+00&A
MODE 1
0
+00&A
+00&A
MODE 1
0
+00&A
+00&A
MODE 1
0
IPOS (R) ADJ
CLEANING MODE
BACK ADJUST
PRIORITY FEED
PRIORITY MODE
PRIORITY HEATER
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
Example of paper registration
1.
Select a paper number to be registered newly or revised.
(1) Press the
key to enter to the ENTRY menu.
INK
ENTRY
F.ADJ
PAPER
(2) Select "SELECT PAPER" menu with the
and
keys.
#SELECT PAPER
>01 : TYPE01
(3) Press the
key to change the parameter.
#SELECT PAPER
>01 : TYPE01
(4) Select a paper number to be registered with the
keys.
and
#SELECT PAPER
>02 : TYPE02
(5) Press the
key to fix the paper number. The display
returns to (2) display.
#SELECT PAPER
>02 : TYPE02
3-33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Example of parameter setting
In this example, a paper feed adjustment value will be entered.
(1) Select "FEED ADJUST" menu with the
and
keys.
#FEED ADJUST
>02 : 099.80%
(2) Press the
key and revise the parameter.
#FEED ADJUST
*02 : 099.80%
NOTE
- Determine the paper feed adjustment value by printing the
paper feed adjustment pattern.
(3) Press the
key to display the massage.
(This message will be displayed at new registration only.)
#FEED ADJUST
>02 : ENTRY OK?
(4) When the
key is pressed, the paper number 02 is
registered newly and "*" mark that shows the paper has already
registered is displayed. The display returns to (1) display.
#FEED ADJUST
>02 : 099.80%
Press the
key to stop the new registration. The display
returns to (1) display.
3-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
F.ADJ Menu
This menu is used to set paper feed adjustment parameters.
When the
key is pressed, parameters can be set.
INK
ENTRY
F.ADJ
PAPER
#FEED PATTERN
>01 : ROUGH 1
(1) Paper feed adjustment pattern
Prints a pattern for adjusting the paper feed amount.
Two pattern parameters are available, ROUGH that prints the paper
feed amount adjustment pattern at every 0.25% step between 99.0
and 101.0 %, and DETAIL that prints the paper feed amount
adjustment pattern at every 0.06% step between current setting
value ±0.12%.
Obtain approximate value with the ROUGH parameter, and
determine the setting value with the DETAIL parameter. Select a
proper parameter according to the print mode.
Press the
key during print to stop the print.
# FEED PATTERN
>ROUGH (NORMAL)
<Parameter (Enter a choice)>
-
ROUGH (NORMAL):
Select at adjustment in standard and high speed print modes.
ROUGH (H-QUAL):
-
Select at adjustment in high quality print mode.
3-35
Download from Www.Somanuals.com. All Manuals Search And Download.
-
-
-
-
-
-
ROUGH (H-DENS):
Select at adjustment in high density print mode.
ROUGH (DRAFT):
Select at adjustment in draft print mode.
DETAIL (NORMAL):
Select at adjustment in standard and high speed print modes.
DETAIL (H-QUAL):
Select at adjustment in high quality print mode.
DETAIL (H-DENS):
Select at adjustment in high density print mode.
DETAIL (DRAFT):
Select at adjustment in draft print mode.
(2) Paper feed correction value setting (FEED ADJUST)
Sets the paper feed adjustment correction value.
Enter a correction value according to the paper feed adjustment
pattern print.
The BASE value is displayed alternately on the 1st line.
BASE=099.88%
>01 : 099.80%
FEED ADJUST
>01 : 099.80%
<Parameter (Enter a value)>
xxx.xx% (97.00 to 103.00)
3-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(3) Back feed adjustment pattern
Prints a pattern for adjusting a paper back feed amount.
Select a proper parameter according to the print mode.
# BACK PATTERN
>NORMAL
<Parameter (Enter a value)>
-
-
-
-
NORMAL:
Select at adjustment in standard and high speed print modes.
H-QUALITY:
Select at adjustment in high quality print mode.
H-DENSITY:
Select at adjustment in high density print mode.
DRAFT:
Select at adjustment in draft print mode.
(4) Paper back feed correction value (unit: pulse)
Input a correction value of the paper back feed based on the result
of the back pattern.
# BACK ADJUST
>+0000 PULSE
<Parameter (Enter a value)>
±2000 pulse (±5 mm)
1 pulse=2.5µm
3-37
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE Menu
This menu is used to maintain the cap and the wiper as well as to
clean the ink path.
When the key is pressed, the service menu will be operable.
SERVICE
CLEANING
FEED
key
#SERVICE
>SERVICE CLEAN
(1) Service cleaning (SERVICE)
Selects a service cleaning parameter.
#SERVICE
>SERVICE CLEAN
<Parameter (Enter a choice)>
-
SERVICE CLEAN
Use this parameter to clean the head and ink path with the
maintenance liquid while the ink is charged into the printer,
and then recharge the maintenance liquid in the printer to ensure
long-term storage.
Six maintenance liquid cartridges and six dummy cartridges
are mandatory.
-
HEAD WASH
Use this parameter to clean the head with the cleaning liquid
with strong washing power) at cleaning or service cleaning after
long-term time storage.
Six cleaning liquid cartridges and six dummy cartridges are
mandatory.
-
INK CHARGE
Use this parameter when charging the ink in the printer.
3-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(2) Cap cleaning (CAP CLEANING)
Moves the print head carriage to the wiper position so that you can
clean the cap unit manually.
#CAP CLEANING
>
<Parameter (Execution form)>
None
(3) Wiper cleaning (WIPER CLEANING)
The wiper blade is lifted so that you can clean the wiper blade
manually.
#WIPER CLEANING
>
<Parameter (Execution form)>
None
(4) Filling ink to the cap (FILL CAP)
Fills the ink into the cap and soaks the head (nozzle surface) into
the ink for 1 to 2 hours to remove the nozzle clogging.
Use this menu when the print-off cannot be fixed by cleaning
repeatedly.
#FILL CAP
>
<Parameter (Execution form)>
None
NOTE
- Always perform the cleaning (normal) after filling cap action.
- If the print off cannot be corrected even leaving the printer
for 24 hours, contact our service centers.
3-39
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Head height
Use this at head height adjustment.
The cap is opened after performing this operation.
# HEAD HEIGHT
>
<Parameter (Execution form)>
None
# ADJUST HEIGHT
>OK
# ADJUST HEIGHT
>EXECUTING
OPEN REAR COVER
ADJUST HEIGHT
# ADJUST HEIGHT
>
3-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(6) Waste ink saving [Additional functions available from V2.00 or later]
The waste ink saving mode for the auto cleaning operation is set.
# WASTE SAVING
> NORMAL
<Parameter (choice input)>
NORMAL:
Auto cleaning is executed in the normal operation
mode (initial value).
SAVE:
Auto cleaning is executed in the ink saving
operation mode.
NOTE
In the "SAVE" mode, problems such as a nozzle skip could
occur depending on the data. In such a case, set the
"NORMAL" mode.
CLEANING Menu
This menu is used to clean the head of the printer.
When the key is pressed, the cleaning menu will be operable.
SERVICE
FEED
CLEANING
key
#CLEANING
>NORMAL
<Parameter (Enter a choice)>
-
-
-
NORMAL: Cleans the head normally.
SLIGHT: Cleans the head slightly.
STRONG: Cleans the head strongly.
See Section 2, Head Cleaning for details.
3-41
Download from Www.Somanuals.com. All Manuals Search And Download.
FEED Menu
While the
key is held down, the currently selected paper roll is
fed. (If a cut sheet is used, it is discharged.)
A feeding message appears on the LCD.
SERVICE
FEED
CLEANING
key
PAPER FEEDING
When the
key is released, paper feeding stops and the top
menu appears on the LCD in offline mode.
FUNC Menu
This menu is used to execute functions provided for the printer.
When the
key is pressed, functions can be executed.
FUNC
SYSTEM
RESET
ADJUST
key
# MENU PRINT
>
3-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(1) Menu print (MENU PRINT)
Prints information on the unit and panel settings.
#MENU PRINT
>
<Parameter (execution form)>
None
(2) Error log information print (ERROR LOG PRINT)
Prints error log information saved in the printer.
#ERROR LOG PRINT
>
<Parameter (execution form)>
None
(3) SCSI trace information print (TRACE PRINT)
Prints SCSI protocol trace data. It is printed only when the SCSI
trace is set to ON.
#TRACE PRINT
>
<Parameter (execution form)>
None
[Additional functions available from V2.00 or later]
(4) History print
The maintenance data are printed.
#HISTORY PRINT
>
<Parameter (execution form)>
None
3-43
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUST Menu
This menu is used to set mechanical adjustment parameters.
When the
key is pressed, mechanical adjustment parameters
can be set.
FUNC
SYSTEM
RESET
ADJUST
key
#ADJUST PATTERN
>TEST PRINT
(1) Adjustment pattern print (ADJUST PATTERN)
Prints the adjustment pattern for adjusting the printer mechanically
and electrically.
When the
stopped.
key is pressed during printing, the print can be
#ADJUST PATTERN
>TEST PRINT
<Parameter (Enter a choices)>
- TEST PRINT:
Prints a block pattern with black and other
color.
- HEAD ADJ 1:
- HEAD ADJ 2:
Prints a head adjustment pattern.
Prints a pattern for checking the head
adjustment.
- ADJUST 1-1:
- ADJUST 1-2:
- ADJUST 1-3:
Prints only the left and right adjustment
pattern of HEAD ADJ 1.
Prints only the inter-head position
adjustment pattern of HEAD ADJ 1.
Prints only the reciprocating adjustment
pattern of HEAD ADJ 1.
3-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
- ADJUST 2-1:
- ADJUST 2-2:
Prints the phase, left and right, and inter-head
position adjustment patterns of HEAD ADJ 2.
Prints only the reciprocating adjustment
pattern of HEAD ADJ 2.
(2) Nozzle jetting position adjustment (Bk/Lm/Lc/Y/M/C) (L/R ADJ YY)
Adjusts the jetting position of nozzle.
Enter an adjustment value according to the head adjustment pattern.
#L/R ADJ YY
YY: Ink color
>+00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
(3) Head position adjustment (Lm/Lc/Y/M/C) (H-POS ADJ YY)
Adjusts the head position for the scanning direction.
Enter an adjustment value according to the head adjustment pattern.
#H-POS ADJ YY
YY: Ink color
>+00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
3-45
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Reciprocating position (Left) adjustment (Bk/Lm/Lc/Y/M/C)
Adjusts the head reciprocating position (Left).
Enter an adjustment value according to the head adjustment pattern.
#I-POS (L) ADJ YY
YY: Ink color
>+00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
(5) Reciprocating position (Right) adjustment (Bk/Lm/Lc/Y/M/C)
Adjusts the head reciprocative position (Right).
Enter an adjustment value according to the head adjustment pattern.
#I-POS (R) ADJ YY
YY: Ink color
>+00&A
Display order:
Bk -> Lm -> Lc -> Y -> M -> C
<Parameter (Enter a value)>
- Sign: +/-
- Value:-32 to +31, A to H (A=0/8, B=1/8...H=7/8)
3-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
SYSTEM Menu
This menu is used to set or display system parameters.
When the key is pressed, system parameters can be set.
FUNC
SYSTEM
RESET
ADJUST
key
#LANGUAGE
>JAPANESE
(1) Language for LCD messages (LANGUAGE) [Initial value: ENGLISH]
Sets Japanese or English for messages displayed on the LCD.
<Parameter (Enter a choice.)>
- ENGLISH
: Displays English messages.
- JAPANESE : Displays Japanese messages.
(2) BOOT version display (BOOT VERSION)
Displays the BOOT version.
#BOOT VERSION
X: Boot version
*X.XX
<Parameter (Execution form)>
None
(3) F/W version display (F/W VERSION)
Displays the engine firmware version.
# F/W VERSION
*X.XX_YY
X: System program version number
Y: Control number
<Parameter (Execution form)>
None
3-47
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Engine controller board version display (IPB VERSION)
Displays the version number of the Engine controller board (IPB).
# IPB VERSION
X: Version number
* X.X
<Parameter (Execution form)>
None
(5) SCSI board version display (WIM VERSION)
Displays the ICB board version.
# WIM VERSION
X: Version number
* X.X
<Parameter (Execution form)>
None
(6) ICB board version display (ICB VERSION)
Displays the version number of the SCSI board (WIM).
#ICB VERSION
X: Version number
*X.XX
<Parameter (Execution form)>
None
(7) ASIC version display (ASIC VERSION)
Displays the ASIC version.
#ASIC VERSION
*X.XX
X: Version number
<Parameter (Execution form)>
None
3-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
(8) Heater H/W version display
Displays the heater hardware version.
#HEART HW VERSION
*XX.X
X: Version number
<Parameter (Execution form)>
None
(9) Heater F/W version display
Displays the heater firmware version.
If the heater cannot be recognized, "--.-" is displayed.
#HEAT FW VERSION
*XX.X
X: Version number
<Parameter (Execution form)>
None
(10) SCSI ID number display (SCSI ID)
Displays the SCSI ID number set with the rotary switch on the
SCSI board.
# SCSI ID
* ID : X
X: ID number
<Parameter (Execution form)>
None
(11) System date setting (SYSTEM DATE)
Sets system date used in the unit in the order of YY (year), MM
(month), DD (day).
#DATE (YY/MM/DD)
>03 / 08 / 01
<Parameter (Enter a value)>
00/01/01 to 99/12/31
3-49
Download from Www.Somanuals.com. All Manuals Search And Download.
(12) System time setting (SYSTEM TIME)
Sets system time used in the unit.
#SYSTEM TIME
>03 / 08 / 01
<Parameter (Enter a value)>
00 : 00 to 23 : 59
(13) Factory setting (INITIAL SET)
Sets all parameter values to factory settings.
#INITIAL SET
>
<Parameter (Execution form)>
None
3-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
RESET Menu
This menu is used to reset the printer.
When the key is pressed, the reset function is executed.
An initializing message appears on the LCD.
FUNC
SYSTEM
ADJUST
RESET
key
INITIALIZING
WAIT A MOMENT
After resetting, the printer goes online.
-
The set values including correction values are not cleared.
HINT
3-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 Heater Controller Operation
This section describes temperature control, LCD displays, param-
eter setup mode operations, and error messages of the heater con-
troller.
Contents of This Section
Temperature Control
LDC Display
Parameter Setup Mode
Error Messages
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Control
The following are three conditions for heater control.
(1) Preset temperature maintaining condition
Function:
To heat the paper for reduction of ink dry time,
improvement of ink fixing, and paper winkles
protection.
Status:
Status of maintaining each heater temperature at
the preset temperature on the heater control panel.
(1) In case the heater ON/OFF setting on the
heater control panel is set to ON and the print
start command is received.
Conditions:
(2) Under the condition (1) above, in case of the
time specified by the delay time after the
print end command was received.
(2) Standby temperature maintaining condition
Function:
To shorten time reaching the preset temperature
at print start.
Status:
Status of maintaining the heater temperature at the
specified standby temperature (35 °C) for
all heaters.
When the preset temperature is lower than the
specified stand by temperature (35 °C), the printer
maintaines the preset temperature.
In case of time specified as the standby time after
completion of the preset temperature maintaining
condition.
Condition:
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Control
(3) Temperature Control Stop Condition
Function:
To prevent useless current consumption, to protect
the paper from being damaged due to the heating
of heaters, and to protect the user from getting
burned due to a touch to the heaters when print is
not performed.
Status:
Status of reaching the environmental temperature
slowly.
Condition:
In case of conditions other than preset
temperature maintaining condition and standby
temperature maintaining condition.
Start of heating
End of print
(Temperature)
End of heating
Print heater preset temperature
Rear heater preset temperature
Front heater preset temperature
Standby temperature
Start of print
Environmental temperature
Delay
time
Delay
time
Standby setting
time
Standby setting
time
setting
value
setting
value
Print
Print
(Time)
Keeping of the
stand by temperature
Keeping of the
stand by temperature
Keeping of the
preset temperature
Stop of the
temperature control
Keeping of the
preset temperature
Start of heating: The print start command is received and the
heating starts. (The print operation does not
start until the heaters reach the preset tempera-
ture. However, if "WAIT HEATER" is set to
"SKIP", the print operation starts even though
the heaters do not reach the preset temperature.)
Start of print:
End of print:
The heaters reached the preset temperature and
the print operation starts.
The print end command is received and the
print operation finishes.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display
(1) Display in normal mode
Preset temperature
Current temperature
AAAU BBBU CCCU
XXXU YYYU ZZZU
Front heater
Print heater
Rear heater
Display: (AAA to CCC, YYY to ZZZ) Temperature unit: (U)
Setup Current
temperature temperature
Celsius
C
F
Heater
Fahrenheit
FRONT
PRINT
REA
AAA
BBB
CCC
XXX
YYY
ZZZ
• Preset temperature display
When using fahrenheit display, the temperature is displayed by
three digits.
(99 fahrenheit or less temperature is displayed with space ;plus
2 digits.)
• Display renewal period
The temperature is measured at every 5 second and renewed.
(2) Display at heater ON
AAAU BBBU CCCU
XXX+ YYYU ZZZU
Heater ON
When each heater is heated, “+” is displayed in place of the unit of
each heater current temperature on the second line. The unit display is
restored at the completion of heating. In the display example shown
above, the front heater is heated.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
LDC Display
(3) Display at heater OFF
“OFF” is displayed in the setup temperature display area of the
heater turned OFF.
The temperature unit of the heater turned OFF is not displayed.
The current temperature area is displayed as it is.
OFF BBBU CCCU
XXXU YYYU ZZZU
(4) Display when heater AC power is turned OFF
“TURN ON HEATER POWER SWITCH” massage is displayed
on the LCD.
TURN ON HEATER
POWER SWITCH
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter Setup Mode
This mode is used when the operator sets the heater control system
parameters.
(1) Setup items and parameters
The setup items and parameters are listed in the table below.
Parameters
Display
(lower line)
Item Display
(upper line)
No.
Item
Description
Initial value
CELSIUS
FAHRENHEIT
1
2
Temperature unit UNIT
Heat suspending
-
CELSIUS
DELAY TIME
00 to 30 MINUTE UNIT: minute
05 MINUTES
time after printing
Standby heating
time after
completion of
DELAY TIME
0, 30, 60, 90, 120,
Unit: minutes
ENDLESS
3
4
5
STANDBY TIME
VERSION
30
-
Version display
FW=vv.r HW=vv.r Display only
NO: Does not perform
the diagnostics.
YES: Performs the
diagnostics.
Diagnostics
DIAGNOSTICS
NO, YES
NO
ENGLISH
JAPANESE
6
7
Display language LANGUAGE
Exit of setup mode EXIT
-
ENGLISH
YES
YES: Exits from the
parameter mode.
NO: Does not exit from
the parameter mode.
YES, NO
*1 Display only, ON/OFF key is ignored.
(2) Entering the parameter setup mode
Press the ON/OFF key,
key, and
key on the heater control
panel at the same time to enter to the parameter setup mode.
The 1st setup item in the parameter setup mode will be displayed.
# UNIT
* CELSIUS
Note: # will be blinked.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter Setup Mode
(3) Moving the setup item
Select a setup item you desire with the
heater control panel.
Press the key on the heater control panel to move to the next
and
keys on the
(lower) setup item.
When pressing
key on the heater control panel at the last setup
item, the (See, (1) setup items and parameters)
Press the
key on the heater control panel to move to the
previous (upper) item.
(See (1) Setup items and parameters))
(4) Selecting the setup item
When the setup item you want to set a parameter is displayed, press
the ON/OFF key on the heater control panel to enter the setup item.
(Example) Temperature unit setting.
# UNIT
* CELSIUS
Note: - # will be returned to normal display.
- * shows blinking.
(5) Selecting a setting value
Selects a setting value with
and
keys on the heater
control panel.
Press the
key on the heater control panel on the temperature
unit setting screen.
# UNIT
* FAHRENHEIT
Note: - * shows blinking
Press the
key on the heater control panel to move to the previ-
ous (upper) setup item.
Press the
key on the heater control panel to move to the next
(lower) setup item.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Deciding the setting value.
Display the setting value you desire on the 2nd line.
Press the ON/OFF key on the heater control panel to determine the
setting value.
The display returns to the setup item setting screen.
# UNIT
* FAHRENHEIT
Note: - # shows blinking
When the setting value you don't desire is displayed on the 2nd
line, press the ON/OFF key on the heater control panel to cancel
the setting value and return to the setup item selection screen.
(7) Exiting from the parameter setting mode.
Move to the last setup item, EXIT menu.
# EXIT
* YES
Note: - # shows blinking
Press the ON/OFF key on the heater control panel.
# EXIT
* YES
Note: - * shows blinking
Press the ON/OFF key on the heater control panel.
AAAU BBBU CCCU
XXXU YYYU ZZZU
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter Setup Mode
(8) Preheat by manual operation
[Additional functions available from V2.00 or later]
The front heater, print heater, and rear heater start to heat until they
reach the set temperature by pressing simultaneously respective
ON/OFF buttons on the heater panel.
Simultaneous pressing
Turning on respective heaters in prior to the print can shorten the
heater temperature rise waiting time at the start of printing.
NOTE
- After the heating started by manual operation, the heaters
turn off automatically through the delay time and standby
time set by the parameters.
- During the printing, these buttons function as normal ON/
OFF buttons.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
When the following error messages are displayed on the heater
control panel, contact our service centers.
<System error>
ERROR H01
SYSTEM ERROR
<The relay board cannot be detected>
ERROR H02
PLY BOARD ERR
<Front heater thermistor temperature error> (-10 °C or less, 70 °C or more)
ERROR H03
F TEMP ERR
<Rear heater thermistor temperature error> (-10 °C or less, 70 °C or more)
ERROR H04
R TEMP ERR
<Print heater thermistor temperature error> (-10 °C or less, 70 °C or more)
ERROR H05
F TEMP ERR
<Front heater thermistor cannot reach the preset temperature
even after 15 minutes>
ERROR H06
F TEMP ERR
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
<Rear heater thermistor cannot reach the preset temperature even after
15 minutes.>
ERROR H07
R TEMPERR
<Print heater thermistor cannot reach the preset temperature even after
15 minutes.>
ERROR H08
P TEMPERR
<Switch test error occurs in the diagnostics >
ERROR H09
SWITCH ERROR
<Zero cross error occurs in the diagnostics.>
ERROR H10
ZERO CROSS ERROR
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 Troubleshooting
This section describes troubleshooting for the printer. If the prob-
lem cannot be solved, contact your dealer or our service center.
Contents of This Section
Troubleshooting
Clearing Paper Jams
When an Error Message Appears
Service Call Errors
Communication Errors
Operator Call Errors
When the Printer Fails to Work Correctly
When a Print Error Occurs
When There is an Abnormal Sound
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before deciding that there is a serious problem with the printer,
check the following items.
Items to be checked
Symptom
Items to be checked
Corrective measures
Plug the power cable into the outlet correctly.
Supply the power to the outlet.
Power cable connection
Power supply to the outlet
No powering
Turn the power switch ON.
See Section 2, Turing the Power ON/OFF.
Power switch ON/OFF
Printer status
The paper guide is heated during printing.
Be sure the paper guide is heated by printing the test
pattern.
The paper guide is not
heated even when the
heater is turned ON.
Press the ON key of the heater
(FRONT/PRINT/REAR) you desire again and then
be sure the paper guide is heated by printing the test
pattern.
Heater control panel
Take appropriate measures according to the error
message. See Section 5, When an Error Message
Appears.
The printer fails to start or ERROR lamp and message on
operate correctly
the LCD
Connect the interface cable correctly.
See Section 2, Turing the Power ON/OFF.
Interface cable connection
Take appropriate measures according to the error
message. See Section 5, When an Error Message
Appears.
ERROR lamp and message on
the LCD
Cannot print
Print nozzle adjustment pattern. See Section 3,
Mechanical Adjustment Menu.
ERROR lamp OFF
The transmitted data is not
processed immediately
Check the communication conditions to the
computer.
DATA lamp (flashing?)
Check for improvement by changing the settings of
heater temperature, print mode, RIP, etc. If not
improved, the paper will not be suitable for the ink.
Replace the paper with other type.
Paper type
Ink type
Use our recommended ink.
See Appendix, Consumables.
Clean the ink head.
See Section 2, Head Cleaning.
Ink head cleaning
Poor print quality
Set the color stripe.
See, Section 3 Entry Menu, (19) Color stripe setting.
Color stripe is not set.
Set the head mode to HILIGHT PRIORITY.
See Section 3, Entry Menu, (18) Head action mode
setting.
Print dot-off occurred in low
printing rate color.
Operational temperature
Use the printer in 20 to 25 ° C temperature.
Check whether the paper type setting matches the
type of the loaded paper. See Section 2, Installing
Paper Roll in the Printer and Removing the paper
roll from the Printer.
Paper type
Use our recommended paper.
See Appendix, Consumables.
Paper jams occur
frequently
Set the paper correctly.
See Section 2, Replacing the Paper Roll.
Paper setting
Check whether there is any
foreign material in the carriage
path or the paper path.
Remove any foreign material.
See Section 5, Clearing Paper Jams.
Print is slow
Operational temperature
Use the printer in 20 to 25 ° C temperature.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jam
Clear paper jams according to a guidance message displayed on
the LCD.
A guidance message appears on the LCD.
1
X: Types of paper jam
1: Paper jam 1
LIFT LEVER &
X
OPEN REAR COVER
2: Paper jam 2
See “When an Error Message Appears”.
Open the pressure roller up/down lever and rear cover.
2
Rear cover
Carriage
Pressure roller up/
down lever
REMOVE PAPER
CLOSE REAR COVER
Remove the jammed paper, check there is no obstacles
in the carriage path and the paper transporting path, and
close the rear cover.
3
Carriage
CARRIAGE MOVING
WAIT A MOMENT
The carriage will move to its home position.
4
5
Set the paper according to the Installing Paper Roll in the
Printer and Removing the Paper Roll from the Printer.
(See page 2-11.)
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
When an Error Message Appears
If the ERROR lamp lights, check the message to be displayed on
the LCD.
There are four types of error messages.
- Service call errors:
Operator unrecoverable errors, such as H/W, S/W failure.
Contact our service centers.
- Communication errors:
Communication protocol errors.
Take appropriate measures according to the error code or
message.
- Operator call errors:
The operator can correct these errors.
Take appropriate measures according to the message.
The error messages are as follows. Take appropriate measure
according to the error message.
If a communication error or a data error occurs, the ERROR
lamp does not light. An error message appears on the LCD
HINT
and disappears when the next operation is performed.
Service Call Errors
If any of the following service call error messages appears, turn
the power switch off and then on again. This may release the
HINT
error.
<POC error>
INITIALIZING
nnnn: Error code
E E n n n n
Description: An unrecoverable error has occurred in the engine section.
(This error message appears when an error is detected
during self-diagnosis after the power is turned on.)
Measure : Contact your dealer or our service centers (The error code
identified on the LCD is needed) .
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
When an Error Message Appears
<Engine error>
ENGINE ERROR nnnn
POWER OFF/ON
nnnn: Error code
Description: An unrecoverable error has occurred in the network
controller section. (H/W failure)
Measure : Contact your dealer or our service centers (The error code
identified on the LCD is needed) .
<System error>
F_e s : n n n n
nnnn: Error code
POWER OFF/ON
Description: An unrecoverable error has occurred. (F/W failure)
Measure : Contact your dealer or our service centers (The error code
identified on the LCD is needed) .
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Communication Errors
nnn: Error code
PRINT READY
001: Parity error
W SCSI ERROR nnn
002: Bus timeout error
Description: The conditions or protocol for communication with the
computer is incorrect.
Measure : (1) Check the SCSI cable connection and terminator
switch.
(2) Set the host SCSI parity bit generation setting to ON.
(3) Check the host SCSI driver setting.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
When an Error Message Appears
Operator Call Errors
The following errors can be corrected by the operator.
(Ink cartridge)
OPEN X INKCOVER
X: L (left) /R (Right)
YY: Y, M, C, Bk, Lm, Lc
CHANGE YY INK
Description: There is no ink.
Measure : Take appropriate measures according to the message.
=> Section 2 Basic Operations (Ink Cartridge Replacement)
OPEN X INKCOVER
CHECK YY INK
Z
X: L (left) /R (Right)
YY: Y, M, C, Bk, Lm, Lc
Z: Error code (1 to 9)
Description: An ink cartridge error has occurred.
Measure : Take appropriate measures according to the message.
=> Section 2 Basic Operations (Ink Cartridge Replacement)
OPEN X INKCOVER
SET YY INK
X: L (left) /R (Right)
YY: Y, M, C, Bk, Lm, Lc
Description: No ink cartridge is installed.
Measure : Take appropriate measures according to the message.
=> Section 2 Basic Operations (Ink Cartridge Replacement)
INKCOVER IS OPEN
X: L (left) /R (Right)
CLOSE X INKCOVER
Description: The ink cover is open.
Measure : Take appropriate measures according to the message.
- The ink LED flashes.
Description: Ink is running out. (Warning)
Measure : Prepare a new ink cartridge.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
(Waste ink bottle)
WASTE INK FULL
CHANGE BOTTLE
Description: The waste ink bottle is full.
Measure : Take appropriate measures according to the message.
=> Section 2 Basic Operations (Waste Ink Bottle Replacement)
BOTTLE ISN’T SET
SET BOTTLE
Description: No waste ink bottle is installed.
Measure : Take appropriate measures according to the message.
=> Section 2 Basic Operations (Waste Ink Bottle Replacement)
(Paper jam)
LIFT LEVER &
1
OPEN REAR COVER
Description: Paper jam (1) occurs when the carriage cannot be driven
due to obstacles in carriage path or paper feed path.
Measure : Take appropriate measures according to the message.
If paper jam (1) occurs frequently even when no paper jams
or there is no obstruction in the carriage path or paper
transfer route, please contact our service center.
=> Section 5 Troubleshooting (Clearing Paper Jam)
LIFT LEVER &
2
OPEN REAR COVER
Description: Paper jam (2) occurs when paper is not detected correctly
due to wrong selection of paper roll or cut sheet or use of
cut sheet with an irregular size.
Measure : Take appropriate measures according to the message.
Also, check setting parameters.
=> Section 5 Troubleshooting (Clearing Paper Jam)
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
When an Error Message Appears
(Paper)
LIFT LEVER
SET PAPER
Description: Paper runs out.
Measure : Set new paper.
=> Section 2 Basic Operations (Paper Replacement)
LIFT LEVER
CHECK PAPER
Description: Paper with an invalid size (less than 297 mm width or 64
inch width or more) is set.
Measure : Set paper with a correct size.
=> Section 2 Basic Operations (Paper Replacement)
LIFT LEVER
SET PAPER
Description: Paper skews.
Measure : Set paper correctly.
Ink may be attached to the platen according to skew
conditions. Wipe off ink on the platen.
=> Section 2 Basic Operations (Paper Replacement)
SET PAPER
PUSH DOWN LEVER
Description: The lever is in the up-position.
Measure : Set paper according to the message.
- Error LED is blinking
Description: Winding failed in the winder.
Measure : Remove the paper in the vicinity of winding sensor.
Check if the paper is set correctly.
=> Section 2 Installing Paper on Winder
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
(Others)
CLOSE REAR COVER
Description: The rear cover is opened.
Measure : Take appropriate measures according to the message.
HEAD TEMP. ERROR
WAIT A MOMENT
Description: The head temperature is out of the operating temperature
range.
Measure : Use it within the operating temperature range. Leave the
printer for a while until the head temperature falls within
the range.
ENV. TEMP. ERROR
CHANGE CONDITION
Description: The ambient temperature is not within the operating
temperature range for the printer.
Measure : Use it within the operating temperature range (15 °C to
30 °C).
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
When the Printer Fails to Work Correctly
This section describes what to do when the printer fails to work
correctly. Take appropriate measures according to the symptoms.
Measures to be taken when the printer malfunctions
Problem
Possible cause
Corrective measure
A no-ink message is
displayed even when
there is enough ink.
Open the ink cover and check whether
The ink bottle is not installed correctly. the joint is correctly inserted into the
ink bottle.
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
When a Print Error Occurs
This section explains how to solve print quality problems. Take
appropriate measures according to the symptoms.
Measures to solve print quality problems when a print error occurs
Symptom
Possible cause
Corrective measure
Check print data.
Blank data is transmitted.
Use the printer in the specified
environmental conditions (temperature
and humidity). (See "Section 1,
Environmental Conditions".)
A blank sheet of paper is
output or the printed
drawing is faded.
The environmental conditions do not
meet the printer specifications.
The paper is set incorrectly.
Check the paper settings.
Foreign objects are attached to the
head.
Clean the head from the CLEANING
menu.
Parts of a drawing are
missing or the print is
unclear.
The low printing ratio pattern is printed
continuously at high temperature
environment.
Set the head mode to HILIGHT
PRIORITY.
Check whether the paper is loaded
correctly.
The paper is loaded upside down.
The paper is set incorrectly.
The print is blurred.
Check the paper settings.
Heater temperature will be low.
Raise the set temperature of heater.
Check whether the leading edge of the
The leading edge of the paper is curled. paper is curled. If it is curled, cut the
leading edge.
If it is wrinkled, feed the paper and cut
The paper is slightly folded or winkled.
off the wrinkled part of the paper.
The print is stained.
Clean the platen, referring to "Section
The platen is stained.
2, Inspecion & Maintenance".
The media edge guard or FAN
Set than correctly.
positioning bar is not set correctly.
Parts of a drawing are
missing at print start.
Use the printer in the specified
Environment temperature.
environmental conditions.
Parts of a drawing are
missing even when the
cleaning is performed
repeatedly.
The nozzle is clogged.
Perform the fill cap operation.
Poor print cannot be
improved even when the The cap or wiper is stained.
cleaning is performed.
Be sure whether the cap and wiper are
stained.
If they are stained, clean them.
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
When There Is an Abnormal Sound
If an abnormal sound is heard, contact your dealer or an SIIT ser-
vice center.
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
This Appendix shows the basic specifications, components,
and celsius and fahrenheit conversion list.
Contents of This Section
Basic Specifications
Printer Specifications
Options/Consumables
Options
Consumables
Celsius and Fahrenheit Coversion List
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Specifications
Printer Specifications
Basic printer specifications
Item
Specification / Function
Piezo-type color ink-jet printing
Recording method
Resolution
720 dpi x 720 dpi
About four minutes / A0 with 4 pass printing. (Changes according to
surrounding temperature and head temperature)
Recording speed
Paper feed/delivery direction Front paper supply, Rear paper delivery
Paper type
Vinyl chloride, Tarpolin
Maximum 64 inch
Paper width
Six colors (black, cyan, magenta, yellow, light magenta, light cyan)
1000 ml ink bottles
Ink cartridge
Standby: 45 dB(A) or less
Operating: 60 dB(A) or less (Continuous sound)
Noise
Heat output
Printer: 720000J/H or less, Heater: 5148000J/H or less
Area excluding top, bottom margines (5 mm) and right and left margins (5
mm) (When using the paper edge guard, right and left margines will be 10
mm.)
Maximum print guaranteed
range
Power supply voltage
Frequency
100 to 240 VAC
50/60 Hz ±1 Hz
Printer: 200 W or less (at operating)
Heater: 1440 W or less (at operating)
Power consumption
External dimensions
Weight
2525 mm (W) x 785 mm (D) x 1195 mm (H) ±10 mm
230 kg or less (excluding paper roll and ink)
Operating
temperature/humidity range
15 to 30 ° C/30% to 70% RH (No condensing)
Non-operating
temperature/humidity range
5 to 35 ° C/10% to 80% RH or less (No condensing)
Installation space
Maintenance space
3325 mm (W) x 2785 mm (D) x 1700 mm (H)
3325 mm (W) x 2785 mm (D) x 1700 mm (H)
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Options/Consumables
Options
Options
Name
Item number Quantity
Remarks
Drys up the media.
Dryer 64
IP-260
IP-263
IP-261
1
1
1
Dryer 64 for North America
Roll Cover 64
Drys up the media.
Protects paper roll from dust.
Mounts an exhaust gas pipe to the
printer or the dryer.
Exhaust Attachment
IP-262
IP-540
IP-541
1
1
1
PS RIP (PhotoPrint 4 DX)
Software RIP (Terminals)
PS RIP (PhotoPrint 4
Server)
Software RIP (Servers)
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
Consumables
(Ink)
Name
Item number Quantity
Remarks
1000 ml
1000 ml
1000 ml
1000 ml
1000 ml
1000 ml
Ink cartridge/Yellow (1000 ml)
Ink cartridge/Magenta (1000 ml)
Ink cartridge/Cyan (1000 ml)
Ink cartridge/Black (1000 ml)
Ink cartridge/Light cyan (1000 ml)
Ink cartridge/Light magenta (1000 ml)
Waste ink bottle
IP6-101
IP6-102
IP6-103
IP6-104
IP6-105
IP6-106
IP6-109
1/carton
1/carton
1/carton
1/carton
1/carton
1/carton
1
(Cleaning Liquid)
Name
Item number Quantity
Remarks
Maintenance liquid cartridge: 6
Dummy cartridge: 6
Storage kit
IP6-137
IP6-117
1
1
Cleaning liquid cartridge: 6
Dummy cartridge: 6
Cleaning kit
*1
100ml/1 pc
*2
Maintenance kit
IP6-108
IP-138
IP-139
IP-147
1
Cap cleaning liquid 6 bottles
Wiper cleaning liquid 6 bottles
Cap cleaning swab
6
1
300 pieces
*1 Cap cleaning liquid : 100 ml, wipe cleaning liquid : 100 ml, cleaning swab : 50 pieces, Syringe : 10 pieces.
*2 Wipe cleaning liquid : 100 ml × 6, Syringe : 10 pieces.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Celsius and Fahrenheit Conversion List
° C
0
F
° C
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
F
° C
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
F
° C
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
F
32
78.8
80.6
82.4
84.2
86
123.8
125.6
127.4
129.2
131
168.8
170.6
172.4
174.2
176
1
33.8
35.6
37.4
39.2
41
2
3
4
5
87.8
89.6
91.4
93.2
95
132.8
134.6
136.4
138.2
140
177.8
179.6
181.4
183.2
185
6
42.8
44.6
46.4
48.2
50
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
96.8
98.6
100.4
102.2
104
141.8
143.6
145.4
147.2
149
186.8
188.6
190.4
192.2
194
51.8
53.6
55.4
57.2
59
105.8
107.6
109.4
111.2
113
150.8
152.6
154.4
156.2
158
195.8
197.6
199.4
201.2
203
60.8
62.6
64.4
66.2
68
114.8
116.6
118.4
120.2
122
159.8
161.6
163.4
165.2
167
204.8
206.6
208.4
210.2
212
69.8
71.6
73.4
75.2
77
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Quasar Garage Door Opener EUR511516 User Guide
Radio Shack Car Video System PLVWR900 User Guide
Radio Shack Clock 02A02 User Guide
RCA Car Speaker 40 5039 User Guide
RCA Flat Panel Television RLED2242A WHITE User Guide
Renesas Network Card REG10J0052 0200 User Guide
Ricoh Computer Hardware R5C841 User Guide
Samson Musical Toy Instrument Scurve 231 User Guide
Sangean Electronics Speaker System RS 332 User Guide
Seagate Flat Panel Television ST11950N ND W WD User Guide