Model No. NTL99011.2
Serial No.
USER’S MANUAL
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-800-TO-BE-FIT
(1-800-862-3348)
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
other electrical devices, except for low-power
devices such as cell phone chargers, into
the surge suppressor or into an outlet on the
same circuit.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Use only a surge suppressor that meets all of
the specifications described on page 17. To
purchase a surge suppressor, see your local
NORDICTRACK dealer, call the telephone
number on the front cover of this manual, or
see your local electronics store.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
13. Failure to use a properly functioning surge
suppressor could result in damage to the
control system of the treadmill. If the control
system is damaged, the walking belt may
slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
5. Place the treadmill on a level surface, with
at least 8 ft. (2.4 m) of clearance behind it
and 2 ft. (0.6 m) on each side. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 26 if the treadmill is
not working properly.)
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by per-
sons weighing 350 lbs. (159 kg) or less.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 19).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes while us-
ing the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds. Ad-
just the speed in small increments to avoid
sudden jumps in speed.
19. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
11. Plug the power cord into a surge suppressor
(not included), and plug the surge suppres-
sor into an appropriate outlet (see page 17).
To avoid overloading the circuit, do not plug
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while
it is running. Always remove the key, unplug
the power cord, and press the power switch
into the off position when the treadmill is not
in use. (See the drawing on page 5 for the
location of the power switch.)
25.
DANGER:
Always unplug the power
cord immediately after use, before clean-
ing the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servic-
ing other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for home use only.
Do not use this treadmill in a commercial,
rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
23. Never insert any object into any opening on
the treadmill.
24. Inspect and properly tighten all parts of the
treadmill regularly.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
NORDICTRACK C 900 PRO treadmill. The C 900
reading this manual, please see the front cover of this
manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
®
PRO treadmill offers an impressive selection of fea-
tures designed to make your workouts at home more
enjoyable and effective. And when you’re not exercis-
ing, the unique treadmill can be folded up, requiring
less than half the floor space of other treadmills.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after
Length: 6 ft. 10 in. (208 cm)
Width: 3 ft. 1 in. (94 cm)
Console
Tray
Heart Rate Monitor
Handrail
Upright
Key/Clip
Power Switch
Power Cord
Walking Belt
Foot Rail
Platform Cushion
Idler Roller
Adjustment Screws
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw-
ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached. Extra hardware may be included.
1/4" Star
Washer (5)–4
#10 Star
Washer (32)–4
5/16" Star
Washer (11)–4
3/8" Star
Washer (13)–4
3/8" Nut (12)–2
#8 x 1/2" Flat
Head Screw (31)–2
#8 x 3/4"
Screw (2)–17
#8 x 1/2"
Screw (1)–14
#8 x 1/2" Ground
Screw (10)–1
#10 x 3/4"
Screw (9)–4
3/8" x 1 1/4"
Screw (8)–4
3/8" x 2" Bolt (3)–1
3/8" x 1 3/4" Bolt (6)–1
5/16" x 2 1/2" Screw (37)–4
3/8" x 2 3/4" Screw (7)–4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Assembly requires two persons.
• To identify small parts, see page 6.
• Assembly requires the following tools:
the included hex key
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• The underside of the walking belt is coated with
high-performance lubricant. After shipping, there
may be some lubricant on top of the walking belt
or on the shipping carton. This is normal. If there
is lubricant on top of the walking belt, wipe it off
with a soft cloth and a mild, non-abrasive cleaner.
one adjustable wrench
one Phillips screwdriver
To avoid damaging parts, do not use power tools.
1. Make sure that the power cord is unplugged.
1
Attach the Left Wheel Cap (96) to the Base (94)
with two #8 x 3/4" Screws (2).
Attach the Right Wheel Cap (not shown) to
the Base (94) in the same way.
94
2
96
2. Pull the Upright Wire (81) and the base ground
wire (A) through the indicated hole in the Base
(94) using the plastic tie.
2
Square
Hole
Attach the base ground wire (A) to the Base (94)
with a #8 x 1/2" Ground Screw (10).
77
Hole
Tie
81
Press the Grommet (77) into the square hole in
the Base (94).
See the inset drawing. Cut the plastic tie near
the Upright Wire (81). Be careful not to damage
the Upright Wire.
10
A
94
Tie
Cut
81
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Identify the Left Upright (89), which is marked
“Left.” Have a second person hold the Left
Upright near the Base (94).
3
81
89
See the inset drawing. Tie the wire tie in the
Left Upright (89) securely around the end of the
Upright Wire (81). Then, pull the other end of the
wire tie until the Upright Wire is routed through
the Left Upright.
Wire
Tie
81
Wire
Tie
89
81
94
4. Hold the Left Upright (89) against the Base (94).
Be careful not to pinch any wires. Insert two
3/8" x 2 3/4" Screws (7) and two 3/8" x
1 1/4" Screws (8) with two 3/8" Star Washers
(13) into the Left Upright.
4
89
Partially tighten the 3/8" x 2 3/4" Screws (7) and
the 3/8" x 1 1/4" Screws (8) until the heads of the
Screws touch the Left Upright (89); do not fully
tighten the Screws yet.
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the right
side.
7
13
8
13
94
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Identify the Left Base Cover (82) and the Right
Base Cover (83). Slide the Left Base Cover onto
the Left Upright (89). Slide the Right Base Cover
onto the Right Upright (90). Do not press the
Base Covers into place yet.
5
93
90
Slide the Console Base Back (93) onto the
Uprights (89, 90).
83
89
82
6. Attach the left handrail assembly (B) to the Left
Upright (89) with two 5/16" x 2 1/2" Screws (37)
and two 5/16" Star Washers (11). Be careful
not to pinch the Upright Wire (81). Start both
Screws and then tighten them.
6
37
11
D
Attach the right handrail assembly (C) in the
same way. Note: There is no wire on the right
side.
81
37
C
B
11
D
Remove and discard the four indicated
screws (D).
89
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Start four #10 x 3/4" Screws (9) with four #10
Star Washers (32) into the Pulse Bar (112) and
the Left and Right Handrails (88, 87).
7
9
C
99
E
32
87
Wire
Tie
Slide the Pulse Bar (112) as far in the direc-
tion shown as possible, and then tighten the
#10 x 3/4" Screws (9). Do not overtighten the
Screws.
112
81
9
Remove the wire tie from the Upright Wire (81).
32
Insert the pulse wire (E) from the Pulse Bar (112)
through the looped Cable Tie (99) on the right
handrail assembly (C).
88
8. Set the console assembly face down on a soft
surface to avoid scratching the console
assembly.
8
1
36
Remove the four indicated 1/4" x 1/2" Screws (4)
from the Console Frame (104). These are used
in assembly step 11.
4
1
27
4
Attach the Left and Right Cup Holders (36, 27)
with eight #8 x 1/2" Screws (1). Do not over-
tighten the Screws.
1
1
104
Console
Assembly
10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Remove the two #8 x 1 1/4" Screws (107) and
slide the Left Handrail Cover (79) back about
1 in. The Screws will be reattached in step
16. Note: It is not necessary to move the Left
Handrail Insert (84).
9
81
Console
Assembly
99
With the help of a second person, hold the con-
sole assembly near the left handrail assembly
(B).
Route the Upright Wire (81) around the back of
the console assembly as shown, and insert the
end of the Upright Wire through the indicated
looped Cable Tie (99).
B
79
84
107
10. Remove the two #8 x 1 1/4" Screws (107) and
slide the Right Handrail Cover (80) back about
1 in. The Screws will be reattached in step 16.
Note: It is not necessary to move the Right
Handrail Insert (85).
10
Console
Assembly
99
E
With the help of a second person, hold the con-
sole assembly near the right handrail assembly
(C).
E
Make sure that the pulse wire (E) is inserted
through the looped Cable Tie (99) on the right
handrail assembly (C).
Route the pulse wire (E) around the back of the
console assembly as shown, and insert the end
of the wire through the other Cable Tie (99).
C
99
85
80
107
11
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Set the console assembly onto the brackets on
the Handrails (87). Be careful not to pinch any
wires.
11
Console
Assembly
Attach the console assembly with the four 1/4"
x 1/2" Screws (4) that you removed in step 8
and four 1/4" Star Washers (5). Start all four
Screws and then tighten them.
87
87
5
4
5
4
12. Set the Console (103) onto the Console Base
(64). Make sure none of the wires from the
Console are pinched.
12
Attach the Console (103) to the Console Base
(64) with six #8 x 1/2" Screws (1).
103
Wires
64
1
1
1
1
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Connect the ground wires (G), the 8-pin wires
(F), the 10-pin wires (E), and the four speaker
wires (H) from the Console (103). Note: The
Upright Wire (81) has 8 pins, the pulse wire (E)
has 10 pins, and the speaker wires (H) have 2
pins.
13
103
G
81
F
E
See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER.
99
99
After all of the wires are connected, pull the
wires tight and tighten the ties (99) around the
wires. Make sure that no wires are resting on
any posts other than those with wire ties. Cut off
the ends of the ties.
99
H
Console
Wire
81
14. Insert the Console Base Back (93) into the hole
in the console assembly and onto the top of the
indicated bracket. Be careful not to pinch any
wires.
14
Tighten two #8 x 1/2" Flat Head Screws (31) into
the tray on the Console Base Back (93).
31
Bracket
93
Console
Assembly
13
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Tighten nine #8 x 3/4" Screws (2) into the
Console Base Back (93) in the indicated loca-
tions, starting with the center Screw.
15
Start First
2
93
2
2
2
2
2
2
16. Slide the Handrail Covers (79, 80) forward until
they match up with the Console Base (64).
Attach the Handrail Covers with the four #8 x 1
1/4" Screws (107) that you removed in steps 9
and 10. Do not overtighten the Screws.
16
Console
Assembly
Tighten four #8 x 3/4" Screws (2) into the con-
sole assembly in the locations shown.
107
2
79
64
Raise the Base Covers (82, 83) and firmly
tighten the four 3/8" x 2 3/4" Screws (7) first and
then the 3/8" x 1 1/4" Screws (8) (only one side
is shown). Then, press the Base Covers into
place.
2
107
80
82
83
7
8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Raise the Frame (56) to the position shown.
17
56
Orient the Storage Latch (53) so that the large
barrel and the latch knob are oriented as shown.
Attach the lower end of the Storage Latch (53) to
the Base (94) with a 3/8" x 2" Bolt (3) and a 3/8"
Nut (12).
6
12
Attach the upper end of the Storage Latch (53)
to the Frame (56) with a 3/8" x 1 3/4" Bolt (6)
and a 3/8" Nut (12).
Latch
Knob
Lower the Frame (56) (see HOW TO LOWER
THE TREADMILL FOR USE on page 25).
53
Large
Barrel
94
12
3
18. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plas-
tic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is
used to adjust the walking belt (see pages 27 and 28).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
• Do not expose the heart rate monitor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° F (50° C) or below 14°
F (-10° C).
The heart rate
monitor consists of
a chest strap and a
Chest
Strap
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sen-
sor under the buckle
on the chest strap.
The tab should be
flush with the front of
the sensor.
• Do not excessively bend or stretch the sensor when
using or storing the heart rate monitor.
Tabs
• To clean the sensor, use a damp cloth and a small
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
Sensor
Tab
TROUBLESHOOTING
If the heart rate monitor does not function properly, try
the steps below.
Sensor
Buckle
The heart rate moni-
tor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the
location shown.
• Make sure that you are wearing the heart rate moni-
tor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
• If heart rate readings are not displayed until you
begin perspiring, rewet the electrode areas.
Make sure that
the logo is right-
• For the console to display heart rate readings, you
side-up. Then, attach the other end of the chest strap
to the sensor. Adjust the length of the chest strap, if
necessary.
must be within arm’s length of the console.
• If there is a battery cover on the back of the sensor,
replace the battery with a new battery of the same
type.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
CARE AND MAINTENANCE
• Thoroughly dry the sensor with a soft towel after
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
• Store the heart rate monitor in a warm, dry place.
Do not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
HOW TO CONNECT THE POWER CORD
nominal 120-volt circuit capable of carrying 15 or
more amps. To avoid overloading the circuit, do
not plug other electrical devices, except for low-
power devices such as cell phone chargers, into
the surge suppressor or into an outlet on the same
circuit. IMPORTANT: The treadmill is not compat-
ible with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
Use a Surge Suppressor
Your treadmill, like other electronic equipment, can be
damaged by sudden voltage changes in your home’s
power. Voltage surges, spikes, and noise interference
can result from weather conditions or from other appli-
ances being turned on or off. To decrease the risk of
damaging the treadmill, always use a surge sup-
pressor with the treadmill. To purchase a surge
suppressor, see precaution 12 on page 3.
1
Grounded Outlet
Grounding Pin
Use only a surge suppressor that is UL 1449 listed as a
transient voltage surge suppressor (TVSS). The surge
suppressor must have a UL suppressed voltage rating
of 400 volts or less and a minimum surge dissipation of
450 joules. The surge suppressor must also be electri-
cally rated for 120 volts AC and 15 amps. There must
be a monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill
and serious injury to users.
Grounding Pin
Surge
Suppressor
Plug in the Power Cord
A temporary
adapter may
be used to
connect the
surge sup-
pressor to a
2
The treadmill must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. The treadmill power cord has a plug with a
grounding pin (see drawing 1 on this page).
2-pole Receptacle
Adapter
2-pole recep-
tacle if a prop-
Lug
erly grounded
outlet is not
available.
Metal
Screw
DANGER:
Improper connection
of the power cord increases the risk of elec-
tric shock. Do not modify the plug—if it will
not fit an outlet, have a proper outlet installed
by a qualified electrician. If you are unsure
whether the treadmill is properly grounded,
contact a qualified electrician.
The lug or wire extending from the adapter must
be connected with a metal screw to a permanent
ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not
grounded. Before using an adapter, contact a quali-
fied electrician to determine whether the outlet box
cover is grounded. The temporary adapter should
be used only until a properly grounded outlet can
be installed by a qualified electrician.
Plug the power cord into a surge suppressor, and plug
the surge suppressor into an appropriate outlet that is
properly installed and grounded in accordance with all
local codes and ordinances. The outlet must be on a
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
You can even listen to your favorite workout music or
audio books with the console’s stereo sound system
while you exercise.
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When you use the manual mode,
you can change the speed and incline of the treadmill
To turn on the power, see page 19. To use the man-
ual mode, see page 19. To use an onboard workout,
with the touch of a button. As you exercise, the console see page 21. To use an iFit Live workout, see page
will display instant exercise feedback. You can even
measure your heart rate using the handgrip heart rate
monitor or the chest heart rate monitor.
22. To use the stereo sound system, see page 23.
To use the information mode, see page 24.
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of mea-
surement is selected, see THE INFORMATION MODE
on page 24. For simplicity, all instructions in this sec-
tion refer to miles.
In addition, the console features thirty-two onboard
workouts—eight calorie workouts, eight incline
workouts, eight intensity workouts, and eight speed
workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective exercise session.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage to
the walking platform, wear clean athletic shoes while
using the treadmill. The first time you use the treadmill,
observe the alignment of the walking belt, and center
the walking belt if necessary (see page 28).
The console also features an iFit Live mode that
enables the treadmill to communicate with your wire-
less network through an optional iFit Live module.
With the iFit Live mode, you can download personal-
ized workouts, create your own workouts, track your
workout results, race against other runners, and
access many other features. To purchase an iFit Live
the telephone number on the front cover of this
manual.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before you turn on the power. If you do
not do this, you may damage the console displays
or other electrical components.
Plug in the power cord (see
page 17). Next, locate the
power switch on the tread-
If the manual mode is not selected, press the
Manual Control button on the console.
Reset
mill frame near the power
3. Start the walking belt.
cord. Press the power
switch into the reset
position.
To start the walking belt, press the Start button, the
Speed increase button, or one of the 1 Step Speed
buttons numbered 1 through 12.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and press the power
switch into the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
24 to turn off the demo mode.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed
increase and decrease buttons. Each time you
press one of the buttons, the speed setting will
change by 0.1 mph; if you hold down the button,
the speed setting will change in increments of 0.5
mph. Note: After you press the button, it may take
a moment for the walking belt to reach the selected
speed setting.
Next, stand on the foot
rails of the treadmill. Find
the clip attached to the key
and slide the clip onto the
waistband of your clothes.
Then, insert the key into the
console. After a moment,
the displays will light.
Key
Clip
If you press one of the numbered 1 Step Speed
buttons, the walking belt will gradually change
speed until it reaches the selected speed setting.
To select a speed setting that includes a decimal—
such as 3.5 mph—press two numbered buttons in
succession. For example, to select a speed setting
of 3.5 mph, press the 3 button and then immedi-
ately press the 5 button. Note: This will not function
if the console is set to metric units.
IMPORTANT: In an emer-
gency, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
To stop the walking belt, press the Stop button. The
time will begin to flash in the display. To restart the
walking belt, press the Start button or the Speed
increase button.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase or decrease button or one of the
numbered 1 Step Incline buttons. Each time you
press one of the buttons, the treadmill will gradually
adjust to the selected incline setting.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Follow your progress with the displays.
Press the Home button to return to the default
menu (see THE INFORMATION MODE on page
24 to set the default menu). If necessary, press the
Home button again.
As you walk or run on the treadmill, the display can
show the following workout information:
• The elapsed time
When an iFit Live module is
connected, the wireless sym-
bol at the top of the display
will show the strength of your
wireless signal. Four arcs
indicate full signal strength.
• The distance that you have walked or run
• The workout intensity bar
• The approximate number of calories you have
burned
To reset the displays, press the Stop button,
remove the key, and then reinsert the key.
• The incline level of the treadmill
• The number of vertical feet you have climbed
• The speed of the walking belt
• Your heart rate (see step 6)
• The matrix
6. Measure your heart rate if desired.
Note: If you use the handgrip heart rate moni-
tor and the chest heart rate monitor at the same
time, the console will not display your heart
rate accurately. For information about the chest
heart rate monitor, see page 16.
Before using
The matrix offers several display tabs. Press the
increase and decrease button next to the Enter
button until the desired tab is shown.
the handgrip
heart rate moni-
tor, remove the
sheets of plastic
from the metal
contacts on the
pulse bar. In
addition, make
sure that your
hands are clean.
The Incline tab will show a profile of the incline set-
tings of the workout. A new segment will appear at
the end of each minute. The Speed tab will show a
profile of the speed settings of the workout.
Contacts
The My Trail tab will show a track that represents
1/4 mile (400 m). As you exercise, the white rect-
angle will show your progress. The My Trail tab will
also show the number of laps you complete.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts; avoid moving your hands. When
your pulse is detected, a heart symbol in the calorie
display will flash each time your heart beats, one
or two dashes will appear, and then your heart rate
will be shown. For the most accurate heart rate
reading, continue to hold the contacts for about
15 seconds.
The Calorie tab will show the approximate amount
of calories you have burned. The height of each
segment represents the amount of calories burned
during that segment. When the Calorie tab is
selected, the calorie display will show the approxi-
mate number of calories burned per hour.
As you exercise, the workout intensity level bar
will indicate the approximate intensity level of your
exercise.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Turn on the fan if desired.
When you select an onboard workout, the display
will show the duration of the workout and the name
of the workout. In addition, a profile of the speed
settings of the workout will appear in the matrix. If
you select a calorie workout, the approximate num-
ber of calories you will burn will appear in the name
of the workout.
The fan features several speed settings and an
auto mode. When the auto mode is selected,
the speed of the fan will automatically increase
and decrease as the speed of the walking belt
increases and decreases.
Press the Manual
3. Start the workout.
fan button repeat-
edly to select a fan
speed or to turn off
the fan. Press the
Auto fan button to select the auto mode or to turn
off the fan.
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
8. When you are finished exercising, remove the
key from the console.
Each workout
is divided into
segments.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
One speed
setting and
one incline
setting are
Current Segment
programmed
for each segment. Note: The same speed setting
and/or incline setting may be programmed for con-
secutive segments.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmill’s electrical components may
wear prematurely.
During the workout, the profiles on the speed and
incline tabs will show your progress. The flash-
ing segment of the profile represents the current
segment of the workout. The height of the flashing
segment indicates the speed or incline setting for
the current segment. At the end of each segment,
a series of tones will sound and the next seg-
ment of the profile will begin to flash. If a different
speed and/or incline setting is programmed for the
next segment, the speed and/or incline setting will
flash in the display to alert you and the treadmill
will automatically adjust to the new speed and/or
incline setting.
HOW TO USE AN ONBOARD WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 19.
2. Select an onboard workout.
To select an onboard workout, press the Calorie
button, the Incline button, the Intensity button, or
the Speed button repeatedly until the desired work-
out appears in the display.
The workout will continue in this way until the last
segment of the profile flashes in the display and the
last segment ends. The walking belt will then slow
to a stop.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on your metabolic rate. In
addition, if you manually change the speed or
incline of the treadmill during the workout, the
number of calories you burn will be affected.
HOW TO USE AN IFIT LIVE WORKOUT
Note: To use an iFit Live workout, you must have an
optional iFit Live module. To purchase an iFit Live
telephone number on the front cover of this man-
ual. You must also have access to a computer with a
USB port and an internet connection. In addition, you
must have access to a wireless network including an
802.11b router with SSID broadcast enabled (hidden
networks are not supported). An iFit.com membership
is also required.
If the speed or incline setting is too high or too low
at any time during the workout, you can manu-
ally override the setting by pressing the Speed or
Incline buttons; however, when the next seg-
ment of the workout begins, the treadmill will
automatically adjust to the speed and incline
settings for the next segment.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 19.
2. Insert the iFit Live module into the console.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment of
the workout begins, the treadmill will automatically
adjust to the speed and incline settings for the next
segment.
To insert the iFit Live module, see the instructions
included with the iFit Live module.
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter in
the iFit Live module must be at least 8 in. (20
cm) from all persons and must not be near or
connected to any other antenna or transmitter.
4. Follow your progress with the displays.
See step 5 on page 20. If you select an onboard
workout, the display will show the time remaining
instead of the elapsed time.
3. Select a user.
If more than one user is registered, you can switch
users in the iFit Live main screen. Press the
increase and decrease buttons next to the Enter
button to select a user.
5. Measure your heart rate if desired.
See step 6 on page 20.
6. Turn on the fan if desired.
See step 7 on page 21.
4. Select an iFit Live workout.
To select an iFit Live workout, press one of the iFit
Live buttons. Before some workouts will download,
you must add them to your schedule on
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 21.
Press the iFit Live button to download the next
workout in your schedule. Press the My Trainer
button, the My Maps button, the World Tour but-
ton, or the Event Training button to download the
next workout of that type in your schedule. Press
the Compete button to compete in a race that you
have previously scheduled. For more information
about the iFit Live workouts, please see
www.iFit.com. Note: If there are no workouts of
the selected type in your schedule, the next work-
out in your schedule will be downloaded.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
When you select an iFit Live workout, the display
will show the duration of the workout, the distance
you will walk or run, and the approximate number
of calories you will burn. The display may also
show the name of the workout. If you select a com-
petition workout, the display will count down to the
beginning of the race.
7. Measure your heart rate if desired.
See step 6 on page 20.
8. Turn on the fan if desired.
See step 7 on page 21.
Note: Each iFit Live button can also run two demo
workouts. To use the demo workouts, remove the
iFit Live module from the console and press one of
the iFit Live buttons.
9. When you are finished exercising, remove the
key from the console.
See step 8 on page 21.
5. Start the workout.
For more information about the iFit Live mode, go
See step 3 on page 21.
During some workouts, the voice of a personal
trainer will guide you through your workout. You
can select an audio setting for your personal trainer
(see THE INFORMATION MODE on page 24).
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio books through the console’s
stereo speakers, you must connect your MP3 player,
CD player, or other personal audio player to the con-
sole through the audio jack below the speakers.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Start button or
the Speed increase button. The walking belt will
begin to move at the speed setting for the first
segment of the workout. When the next segment of
the workout begins, the treadmill will automatically
adjust to the speed and incline settings for the next
segment.
To use the audio jack, locate the included audio wire
and plug it into the audio jack. Then, plug the audio
wire into a jack on your MP3 player, CD player, or
other personal audio player. Make sure that the audio
wire is fully inserted.
Next, press the play button
6. Follow your progress with the displays.
on your MP3 player, CD
player, or other personal
audio player. Adjust the vol-
ume on your personal audio
Decrease
See step 5 on page 20.
The My Trail tab will show a map of the trail you are player or press the volume
Increase
walking or running or it will show a track and the
number of laps you are completing.
increase and decrease but-
tons on the console.
During a competition workout, the Competition tab
will show your progress in the race. As you race,
the top line in the matrix will show how much of the
race you have completed. The other lines will show
your top four competitors. The end of the matrix
represents the end of the race.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat
surface instead of on the console.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
function. If the demo mode is turned on, the word
ON will appear in the matrix. To turn on or turn off
the demo mode, press the Enter button.
The console features an information mode that keeps
track of treadmill information and allows you to person-
alize console settings.
3. CONTRAST LVL: Press the Incline increase and
decrease buttons to adjust the contrast level of the
display.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
If a module is connected, you may also select the
following screen:
The time display will show the total number of hours
the treadmill has been used.
4. TRAINER VOICE: To turn on or turn off the voice
of the personal trainer, press the Enter button.
The distance display will show the total number of
miles (or kilometers) that the walking belt has moved.
If an iFit Live module is connected, you may also
select the following screens:
The lower display will show the status of an iFit Live
module. If an iFit Live module is connected, the display
will show the words WIFI MODULE. If a USB module
is connected, the display will show the words USB/SD
MODULE. If no module is connected, the display will
show the words NO IFIT MODULE.
5. DEFAULT MENU: The default menu will appear
when you insert the key into the console or when
you press the Home button. Press the Enter button
repeatedly to select the manual main screen or the
iFit Live screen as the default menu.
6. CHECK WIFI STATUS: Press the Enter button to
check the status of your iFit Live module. The lower
display will show the software version number, the
network SSID, the network encryption type, the
connection status, the wireless signal strength, the
IP address of the module, the number of registered
users and their names, the results of the DNS
lookup, and the status of the iFit Live server.
While the information mode is selected, the matrix
will display several optional screens. Press the
decrease button next to the Enter button to select
each of the following screens:
1. UNITS: To change the unit of measurement, press
the Enter button. To view distance in miles, select
ENGLISH. To view distance in kilometers, select
METRIC.
7. SEND/RECEIVE DATA: To send and receive work-
outs, workout logs, and updates, press the Enter
button. When the process is finished, the words
TRANSFERS DONE will appear in the display.
2. DEMO: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. While the demo mode is turned
on, the console will function normally when you
plug in the power cord, press the power switch
into the reset position, and insert the key into the
console. However, when you remove the key, the
displays will remain lit, although the buttons will not
To exit the information mode, remove the key from the
console.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to the lowest position before you fold the treadmill.
Then, remove the key and unplug the power cord.
CAUTION: You must be able to safely lift 45 lbs. (20
kg) to raise, lower, or move the treadmill.
Before moving the treadmill, fold it as described at the
left. CAUTION: Make sure that the latch knob is
locked in the storage position. Moving the treadmill
may require two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
1
Frame
Handrail
Frame
Wheel
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the treadmill
without tipping it back, do not pull on the frame,
and do not move the treadmill over an uneven
surface.
2. Raise the frame until the latch knob locks in the
storage position. CAUTION: Make sure that the
latch knob locks.
2
3. Place one foot against a wheel, and carefully lower
the treadmill.
Frame
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2. Hold the upper end of the tread-
mill frame with your right hand. Then, pull the latch
knob to the left. IMPORTANT: Do not turn the
latch knob. If necessary, push the frame forward
slightly. Pivot the frame downward a few inches,
and release the latch knob.
Latch Knob
2. See drawing 1 at the left. Hold the metal frame
firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic
foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following
the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
c. Remove the key from the console, and then
reinsert it.
d. If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The power does not turn on
SYMPTOM: The console displays remain lit when
you remove the key from the console
a. Make sure that the power cord is plugged into a
surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see
page 17). Use only a surge suppressor that meets
all of the specifications described on page 17.
IMPORTANT: The treadmill is not compatible
with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
a. The console features a display demo mode, de-
signed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 24 to turn off the
demo mode.
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
SYMPTOM: The displays of the console do not
function properly
c. Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
a. Remove the key from the console and UNPLUG
THE POWER CORD. Remove the five #8 x 3/4"
Screws (2). Carefully pivot the Motor Hood (65) off.
c
a
2
65
Tripped
Reset
2
SYMPTOM: The power turns off during use
2
a. Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the Reed Switch (52) and the Magnet (50)
on the left side of the Pulley (49). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If nec-
essary, loosen the #8 x 3/4" Tek Screw (14), move
the Reed Switch slightly, and then retighten the
Screw. Reattach the Motor Hood (not shown) with
the five #8 x 3/4" Screws (not shown) and run the
treadmill for a few minutes to check for a correct
speed reading.
b. If the walking belt is overtightened, treadmill per-
formance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
Top
View
b
49
50
2–3 in.
52
14
1/8 in.
Idler Roller Screws
SYMPTOM: The incline of the treadmill does not
change correctly
a. Hold down the Stop button and the Speed increase
button, insert the key into the console, and then
release the Stop button and the Speed increase
button. Press the Stop button and then press the
Incline increase or decrease button. The treadmill
will automatically rise to the maximum incline level
and then return to the minimum level. This will re-
calibrate the incline system. If the incline does not
begin calibrating, press the Stop button again, and
then press the Incline increase or decrease button
again. When the incline is calibrated, remove the
key from the console.
c. Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to the
walking belt or the walking platform unless in-
structed to do so by an authorized service rep-
resentative. Such substances may deteriorate
the walking belt and cause excessive wear. If
you suspect that the walking belt needs more lubri-
cant, see the front cover of this manual.
d. If the walking belt still slows when walked on, see
the front cover of this manual.
SYMPTOM: The walking belt slows when walked on
a. Use only a surge suppressor that meets all of the
specifications described on page 17.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOM: The walking belt is off-center or slips
when walked on
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller screws
clockwise, 1/4 of a turn. When the walking belt is
correctly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off the
walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert
the key, and carefully walk on the treadmill for a
few minutes. Repeat until the walking belt is prop-
erly tightened.
a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn; if the walking belt has shifted to the
right, turn the left idler roller screw counterclock-
wise 1/2 of a turn. Be careful not to overtighten the
walking belt. Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b
a
SYMPTOM: The console display has lines running
through it
a. If lines appear in the console display, see THE
INFORMATION MODE on page 24 and adjust the
contrast level of the display.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretch-
ing and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise—never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your "training zone." The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST
Model No. NTL99011.2 R1111A
Description
Key No. Qty.
Description
Key No. Qty.
1
2
3
4
5
6
7
8
20
77
1
4
4
1
4
4
4
8
4
2
4
13
2
1
2
2
4
2
2
2
4
1
4
2
1
2
1
4
2
4
6
4
1
1
4
8
8
2
8
1
1
1
1
2
1
4
1
1
#8 x 1/2" Screw
#8 x 3/4" Screw
3/8" x 2" Bolt
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
3
1
1
2
1
1
2
1
1
2
1
1
1
1
1
1
1
1
2
2
1
1
1
2
4
1
1
1
1
2
1
9
1
Reed Switch Clip
Reed Switch
Storage Latch
Drive Motor
Motor Belt
Frame
Left Rear Foot
Frame Endcap Cover
Rubber Cushion
Right Foot Rail
Idler Roller
Frame Endcap
Hex Key
Console Base
Motor Hood
Hood Accent
Incline Frame Spacer
Hood Clip
Incline Motor
Incline Frame
Frame Spacer
Controller
Controller Plate
Hood Post
Power Switch
Power Cord
1/4" x 1/2" Screw
1/4" Star Washer
3/8" x 1 3/4" Bolt
3/8" x 2 3/4" Screw
3/8" x 1 1/4" Screw
#10 x 3/4" Screw
#8 x 1/2" Ground Screw
5/16" Star Washer
3/8" Nut
3/8" Star Washer
#8 x 3/4" Tek Screw
Idler Roller Screw
3/8" x 1 1/2" Bolt
3/8" x 1 3/4" Wheel Bolt
#8 x 1 3/4" Screw
#8 x 7/16" Screw
5/16" Motor Screw
3/8" Pin
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
3/8" x 1" Bolt
5/16" x 1 3/4" Shoulder Bolt
1/4" x 1" Screw
#8 x 1" Screw
1/4" x 1 1/2" Screw
Right Cup Holder
Speaker
3/8" x 2" Hex Head Bolt
5/16" Flat Washer
#8 x 1/2" Flat Head Screw
#10 Star Washer
3/8" Jam Nut
Grommet
Belly Pan
Left Handrail Cover
Right Handrail Cover
Upright Wire
Left Base Cover
Right Base Cover
Left Handrail Insert
Right Handrail Insert
#8 Tek Screw
Handrail
5/32" Hex Key
Left Upright
Right Upright
Warning Decal
Base Pad
Console Base Back
Base
Right Wheel Cap
Left Wheel Cap
Wheel
Key/Clip
Cable Tie
Audio Wire
5/16" Nut
1/4" Star Washer
Left Cup Holder
5/16" x 2 1/2" Screw
Isolator Top
Isolator
Isolator Bottom
Isolator Spring
Left Foot Rail
Caution Decal
Walking Platform
Walking Belt
Belt Guide
Right Rear Foot
Cable Tie
Drive Roller/Pulley
Magnet
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
1
1
1
1
1
2
4
8
10
1
Left Speaker Cover
Right Speaker Cover
Console Assembly
Console Frame
Console Ground Wire
Console Clamp
#8 x 1 1/4" Screw
#3 Screw
#6 x 1/2" Screw
111
112
113
114
115
116
117
118
*
1
1
1
2
1
1
1
1
–
Pulse Bar Back
Pulse Bar
Right Speaker Back Cover
Incline Motor Spacer
Fan
Chest Strap
Chest Sensor
Left Speaker Back Cover
User’s Manual
Crossbar Ground Wire
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A
Model No. NTL99011.2 R1111A
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B
Model No. NTL99011.2 R1111A
2
2
2
65
66
29
67
33
69
33
71
16
70
114
62
33
71
10
33
67
72
2
2
2
2
2
73
2
2
76
74
2
2
2
77
2
58
2
10
2
68
2
68
74
2
2
2
75
2
68
78
2
33
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C
Model No. NTL99011.2 R1111A
37
11
5
84
4
79
9
1
32
10
110
111
107
81
86
107
1
1
87
1
9
32
89
82
1
98
112
37
1
5
91
80
85
4
11
87
86
7
90
8
22
107
81
13
7
83
77
10
91
2
92
14
96
97
33
94
22
7
8
92
14
7
17
13
92
17
14
95
92
14
2
97
33
34
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D
Model No. NTL99011.2 R1111A
116
117
103
100
104
105
10
109
118
109
115
106
2
25
109
109
1
101
106
2
99
99
25
1
64
2
28
108
2
108
2
109
1
108
2
2
109
2
31
2
2
2
2
102
1
93
2
1
1
2
113
1
2
2
36
2
2
1
108
108
28
108
1
1
27
1
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and drive motor are warranted for a lifetime.
Parts are warranted for three (3) years from the date of purchase. Labor is warranted for one (1) year from
the date of purchase.
This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is
limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
or if the product is used for commercial or rental purposes. No other warranty beyond that specifically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specific legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 323383 R1111A
Printed in USA © 2011 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|