Model G6V
Universal VisorTransmitter
1. INTRODUCTION
5. BATTERY
Congratulations on your purchase of the Skylink® Universal Visor Trans-
mitter Model G6V. The Model G6V works with the Skylink Smart ButtonTM.
In this package, you will find a visor remote with 12V battery.
12 volt alkaline battery (size 23A)
included.
Universal
VisorTransmitter
(Battery included)
Visor clip
6. ADDITIONAL TRANSMITTER
You can add up to 15 additional transmitters to control the
same receiver. Skylink® offers Keychain Transmitters and
Keypad Transmitters to work with your receiver. For
more information, please visit our website at
2. PROGRAM A VISOR REMOTE TO THE GTR SMART BUTTONTM
Refer to the section in the Skylink® model GTR to install the Smart ButtonTM
and follow the instructions below to program the transmitter.
1. With the GTR Smart ButtonTM connected on your
existing wall button. The red light on the Smart
ButtonTM should flash after plugging in the power.
If the red light on the Smart ButtonTM is flashing
slowly, that indicates it is in standby mode.
2. Press the learn button on the side of the GTR.
3. Once the learn button is pressed, the red LED
will flash quickly. You may release the learn
button.
7. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
4. Press the button on the transmitter you would
like to program.
8. FCC
5. Once the transmitter is programmed, the red
LED will flash slowly, in the same way as it
flashes in standby mode.
6. You can now operate the garage door opener
with this new remote control.
The Garage Door Remote Control is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
Learn Button
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.
3. TROUBLE SHOOTING
9. WARRANTY
Q: Door opener does not react after pressing the button on the transmitter?
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
A: - Ensure the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted
properly.
- Ensure the wires that are previous connected to the wall mounted
door control are not loose.
10. CUSTOMER SERVICE
- Ensure the remote control has been programmed to the Smart
ButtonTM. Refer to section 2 for how to program a transmitter to the
receiver.
If you would like to order Skylink’s product or have difficulty getting your Skylink
remote control to work, please :
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
4. REMOVE THE REMOTE CONTROL FROM THE SMART BUTTONTM
You can delete the remote control(s) from the Smart ButtonTM, first delete
all the remote controls, then learn the ones you would like to keep.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
1. Press and hold the learn button for approx 10 seconds on the Smart
ButtonTM
.
P/N. 101Z487
US Patent. D377458
® are registered trademarks of their respective corporations
©2007 SKYLINK GROUP
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. You may now release
the learn button.
3. You have erased all the remote controls in the Smart ButtonTM
.
Download from Www.Somanuals.com. All Manuals Search And Download.
|