Model No. 831.150860
Serial No.
USER’S
MANUAL
Write the serial number in the space
above for reference.
Serial Number Decal (under seat)
PATENT PENDING
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
To reduce the risk of serious injury, read the following important
precautions before using the weight bench.
WARNING:
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
12. Always place 50 pounds on the leg lever to
balance the bench when performing squat
exercises (see page 11).
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
13. Always fold the backrest out of the way when
performing squat exercises (see page 11). Do
not sit on the seat when the backrest is folded.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.
14. Do not stand with your back to the weight
bench when performing squat exercises (see
page 11).You should be able to see the
weight rests while exercising so that you can
safely return the barbell to the weight rests
when you finish the exercise.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
15. When using the backrest, make sure the
adjustment tube is fully inserted into the
adjustment brackets in the uprights.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
16. Always remove the curl post from the front
leg before performing leg curl or leg exten-
sion exercises with the leg lever (see page
12).
6. Keep children under the age of 12 and pets
away from the weight bench at all times.
7. Keep hands and feet away from moving parts.
17. Always set both weight rests at the same
height. The M10 adjustment knob must
always be inserted through both the upright
and the weight rest and firmly tightened into
the welded nut. Never tighten the M10 adjust-
ment knob into an upright and then set the
weight rest in the upright on top of the
adjustment knob.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. Do not use a barbell (not included) longer
than six feet with this weight bench.
10. When you are using a barbell (not included),
always make sure there is an equal amount
of weight on each side.
18. Always exercise with a partner. When you are
performing bench press exercises, squat
exercises or toe raise exercises, your partner
should stand behind you to catch the barbell
if you cannot complete a repetition.
11. The weight bench is designed to support a
maximum of 460 pounds, including the user,
a barbell and weights. Do not place more
than 210 pounds, including a barbell and
weights on the weight rests. Do not place
more than 130 pounds on the leg lever for
normal use.
19. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. SEARS assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for selecting the versatile WEIDER® PRO
208 Weight Bench. The PRO 208 is designed to help
you develop every major muscle group of the body.
Whether your goal is to tone your body, build dramatic
HELPLINE at 1-800-736-6879, Monday through
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
muscle size and strength or improve your cardiovascu- The model number is 831.150860. The serial number
lar system, the PRO 208 will help you to achieve the
results you want.
can be found on a decal attached to the WEIDER®
PRO 208 Weight Bench (see the front cover of this
manual).
For your benefit, read this manual carefully before
using the WEIDER® PRO 208 Weight Bench. If you
have additional questions, please call our toll-free
Please use the drawing below to familiarize your-
self with the major parts and how they fit together.
Weight Rests
Curl Pad
Adjustment
Knob
Foam Pad
Adjustment
Tube
Backrest
Upright
Leg Lever
Seat
Weight Tube
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R0999A
Part Identification Chart - Model No. 831.150860
M6 x 16mm Screw (45)
M10 Washer (37)
M6 x 40mm Bolt (44)
M8 Washer (21)
M8 x 16mm Bolt (39)
M6 Washer (36)
M8 x 55mm Carriage Bolt (47)
M8 x 58mm Bolt (38)
M8 x 60mm Bolt (48)
M8 x 65mm Bolt (42)
M10 x 70mm Bolt (41)
M8 Nylon Locknut (40)
M10 Nylon Locknut (49)
10mm Plastic Bushing (35)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
• For help identifying the small parts, use the PART
IDENTIFICATION CHART on page 5 of the man-
ual.
Make Things Easier for Yourself!
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Everything in this manual is designed to ensure
that the assembly of our products can be complet-
ed successfully by anyone. However, it is impor-
tant to recognize that your new equipment is a
sophisticated product with many small parts and
consequently, the assembly process will take time.
Most people find that by setting aside plenty of
time, and by deciding to make the task enjoyable,
assembly will go smoothly.
The following tools (not included) are required
for assembly:
• Two (2) adjustable wrenches
• One (1) rubber mallet
• One (1) standard screwdriver
• One (1) phillips screwdriver
• Assembly requires two people.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• Lubricant, such as grease or petroleum jelly
plus soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
1. Before assembling this product, make sure you
have read and understand the information in the
box above.
1
5
39
21
50
Insert a 1 3/4” Slotted Square Inner Cap (50) into the
Bench Frame (5).
Place the Bench Frame (5) in the bracket (A) on the
Front Leg (4) and attach it with three M8 x 16mm
Bolts (39) and three M8 Washers (21). Do not fully
tighten the Bolts.
39
21
39
A
4
Note:The Caps mentioned in all assembly steps
may come pre-assembled from the factory.
2. Press a 2” Square Inner Cap (29) into the lower end
of the Left Upright (8).
2
Welded Nut
Attach the Left Upright (8) to the Left Base (6) with a
Support Plate (28), two M8 x 65mm Bolts (42) and
two M8 Nylon Locknuts (40). Do not confuse the
Left and Right Upright. Locate the welded nut to
identify each Upright.
8
42
Do not tighten the Nylon Locknuts yet.
28
40
6
29
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press a 2” Square Inner Cap (29) into the lower end
of the Right Upright (9).
3
9
Attach the Right Upright (9) to the Right Base (7) with
a Support Plate (28), two M8 x 65mm Bolts (42) and
two M8 Nylon Locknuts (40).
42
40
28
7
29
4. Insert an M8 x 55mm Carriage Bolt (47) through the
front hole in each Base (6, 7). Slide the mounting
bracket (B) on the Bench Frame (5) onto the Carriage
Bolts. Partially tighten an M8 Nylon Locknut (40) onto
each Carriage Bolt.
4
5
40
B
48
Do not tighten the Nylon Locknuts yet.
7
6
Insert two M8 x 60mm Bolts (48) through the mount-
ing bracket (B) on the Bench Frame (5) and the Left
and Right Base (6, 7). Tighten an M8 Nylon Locknut
(40) onto each Bolt. Tighten the Bolts (39) and
Locknuts (40) used in steps 1–4 now.
47
40
5. Press an Outer Upright Bushing (46) onto the top end
of each Upright (8, 9).
5
11
8
Slide a Weight Rest (11) into the Right Upright (9).
Align one of the holes in the Weight Rest with the
hole in the Upright. Insert an M10 Adjustment Knob
(25) through the Upright and the Weight Rest. Tighten
the Knob into the welded nut.
11
46
Insert the other Weight Rest into the Left Upright (8)
in the same manner.
Welded Nut
25
Both Weight Rests must be set at the same
height.
9
6. Press a 1 1/4” Square Inner Cap (34) into each end
of the Adjustment Tube (12).
6
34
Insert the Adjustment Tube into one set of adjustment
brackets (C) on the Uprights (8, 9).
C
12
Make sure the Adjustment Tube (12) is oriented as
shown and that the pins on the Tube are fully
inserted into the slots in the adjustment brackets
(C).
34
8
9
Pin
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Insert a 1” Square Inner Cap (32) into the open end
of each Backrest Tube (13, 14).
7
Insert a 10mm Plastic Bushing (35) into each end of
the welded tubes on the Backrest Tubes (13, 14) as
shown in the inset drawing.
32
13
Welded
Tubes
Identify the Left (13) and Right (14) Backrest Tube.
The welded tube on the front end extends on one
side. This protrusion must be pointed towards the
center of the bench as shown in the inset draw-
ing.
23
14
35
Protrusion
8
8. Refer to the inset drawing for this step.
Lubricate an M10 x 175mm Bolt (43) and slide an
M10 Washer (37) onto it. Push the Bolt through the
welded tube on the Left Backrest Tube (13).
Lubricate
Insert the Bolt through the indicated hole in the Left
Seat Bracket (1). Make sure you have identified the
Left Seat Bracket and that it is oriented as shown
in the drawing.
13
43
37
14
20
1
Slide a Plastic Spacer (20) onto the M10 x 175mm
Bolt (43). Push the Bolt through the holes (D) in the
Bench Frame. Slide another Plastic Spacer (20) onto
the Bolt.
19
49
D
Insert the M10 x 175mm Bolt (43) through the indicat-
ed hole in the Right Seat Bracket (19). Make sure
you have identified the Right Seat Bracket and
that it is oriented as shown in the drawing.
37
5
Push the M10 x 175mm Bolt (43) through the welded
tube on the Right Backrest Tube (14). Secure it with
an M10 Washer (37) and an M10 Nylon Locknut (49).
5
37
37
43
1
19
13
20
20
14
49
Do not overtighten the Nylon Locknut.You must
be able to freely pivot the Backrest Tubes (13, 14)
and Seat Brackets (1, 19).
9. Attach the Backrest (23) to the Left Backrest Tube
(13) and the Right Backrest Tube (14) with four M6 x
40mm Bolts (44) and four M6 Washers (36).
9
23
14
13
36
44
44
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Attach the Seat (22) to the Left Seat Bracket (1) and
the Right Seat Bracket (19) with four M6 x 16mm
Screws (45).
10
22
1
Insert the Seat Pin (15) through the holes in the cen-
ter of the Seat Brackets and the holes in the Bench
Frame (5).
23
15
Make sure the narrow end of the Seat (22) is
pointing towards the Backrest (23).
19
5
45
11. Press a 1” Round Inner Cap (30) into each end of the
weight tube (E) on the Leg Lever (3).
11
3
Press a 1 1/2” Square Inner Cap (33) into each end
of the Leg Lever (3).
33
30
30
E
33
12. Lubricate an M10 x 70mm Bolt (41). Attach the Leg
Lever (3) to the bracket (F) on the Front Leg (4) with
the Bolt and an M10 Nylon Locknut (49).
12
49
F
3
Attach the Leg Lever Lock (2) to the Front Leg (4)
with an M8 x 58mm Bolt (38), an M8 Washer (21) and
an M8 Nylon Locknut (40). Do not overtighten the
Nylon Locknut. The Leg Lever Lock must be easy
to turn.
41
Lubricate
40
4
21
2
38
13. Press six 3/4” Round Inner Caps (31) into the ends of
the three Pad Tubes (16, 17).
13
16
18
F
3
31
Insert a Short Pad Tube (17) through each of the
holes in the Leg Lever (3).
31
Insert the Long Pad Tube (16) through one of the two
sets of holes in the bracket (F) on the Front Leg (4).
17
18
Slide two Foam Pads (18) onto each Pad Tube (16,
17).
18
31
18
17
31
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Attach the Curl Pad (24) to the Curl Post (10) with
two M6 x 16mm Screws (45).
14
24
45
10
15. Make sure all parts are properly tightened before you use the weight bench. The use of all remaining
parts will be explained in Adjusting the Weight Bench starting below.
Adjusting the Weight Bench
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for impor-
tant information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise poster to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE WEIGHT RESTS
11
11
8
To change the height of the Weight Rests (11), first
remove your Barbell (not shown) from the Weight
Rests.
While holding a Weight Rest (11) with one hand, remove
the M10 Adjustment Knob (25) from one Upright (8 or 9).
Slide the Weight Rest to the desired position. Insert the
M10 Adjustment Knob through both the Upright and the
Weight Rest and tighten it into the welded nut. Position
the other Weight Rest in the same manner.
25
Make sure that you fully tighten the M10 Adjustment
WARNING: Always set both weight rests at the
same height. The M10 adjustment knob must
always be inserted through both the upright and
the weight rest and firmly tightened into the welded
nut. Never tighten the M10 adjustment knob into an
upright and then set the weight rest in the upright
on top of the adjustment knob.
9
Knob (25).
Note that for squat exercises the Weight Rests (11) must
be turned around in the Uprights (8, 9).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLDING THE BACKREST
To perform squat exercises, you will need to fold the
Backrest (23) to the upright position.
23
To fold the Backrest (23), lift and pull it forward as far as it
will go. It will be held in place by its own weight.
WARNING: Always fold the backrest out of the way
when performing squat exercises. Do not sit on the
seat when the backrest is folded.
ADJUSTING THE WEIGHT BENCH FOR
SQUAT EXERCISES
To perform squat or toe raise exercises, fold the Backrest
(23) to the upright position as described above.
Remove the Adjustment Tube (12).
Move the Weight Rests (11) to one of the highest posi-
tions (see ADJUSTING THE WEIGHT RESTS earlier in
this section).
11
11
25
Make sure the Weight Rests have been turned around
as shown.
WARNING: Always place 50 pounds on the leg
lever to balance the bench when performing squat
exercises.
23
12
WARNING: Always fold the backrest out of the way
when performing squat exercises.
WARNING: Do not stand with your back to the
weight bench when performing squat exercises.
You should be able to see the weight rests while
exercising so that you can safely return the Barbell
(not included) when you finish the exercise.
ADJUSTING THE LEG SUPPORT PADS
F
The Long Pad Tube (16) with Foam Pads (18) is mounted
in the bracket (F) on the Front Leg (4). It can be placed in
two different positions.
To move the leg support, pull off one of the Foam Pads
(18). Pull the Pad Tube (16) with the remaining Foam Pad
out of the bracket. Insert the Pad Tube in the other hole
and press the Foam Pad back into place.
4
Note: The bracket (F) on the Front Leg (4) may have three
adjustment holes on your particular weight bench.
16
18
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE SEAT INCLINE
Some exercises can be performed more comfortably
when the Seat (22) has a slight incline. To give the Seat
an incline, pull out the Seat Pin (15). Lift up the wide end
of the Seat and insert the Seat Pin (15) through the holes
in the Seat Brackets (1, 19), but not through the holes in
the Bench Frame (not shown). Then lower the Seat again.
22
1
15
To remove the incline, pull out the Seat Pin (15), lower the
Seat (22) and re-insert the pin through the holes in both
the Seat Brackets (1, 19) and the Bench Frame.
19
ATTACHING WEIGHTS TO THE LEG LEVER
3
To use the Leg Lever (3), slide the desired amount of
weight (not included) onto the Weight Tube (E).
WARNING: Do not place more than 130 pounds on
the leg lever.
E
LOCKING THE LEG LEVER
Some exercises, such as sit-ups, can be performed more
comfortably with the Leg Lever (3) locked.
To lock the Leg Lever (3), turn the Leg Lever Lock (2) until
it engages the Short Pad Tube (17).
2
3
17
ATTACHING THE CURL POST
For some exercises, the Curl Post (10) must be attached
to the weight bench.
Insert the Curl Post (10) into the indicated hole in the
Front Leg (4). Align the holes in the Front Leg and the
Curl Post. Secure the Curl Post with the M8 Adjustment
Knob (26). Make sure that you fully tighten the
Adjustment Knob (26).
10
27
26
When the Curl Post (10) is not in use, insert the Front Leg
Endcap (27) halfway into the top of the Front Leg (4).
When the Curl Post (10) is not in use, store it away from
the weight bench so that it does not interfere with your
exercise program.
4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE BACKREST
The Backrest (23) can be set to three different positions:
a level position, a decline position and an incline position.
C
To change the position of the Backrest (23), move the
Adjustment Tube (12) to a different set of adjustment
brackets (C) in the Uprights.
When moving the Adjustment Tube (12), always make
sure the pins on it are seated in the slots in the
adjustment brackets (C).
23
12
Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
ness program, and cross training is a very efficient
way to accomplish this. One example of a balanced
program is:
• Plan weight training workouts on Monday,
Wednesday and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running or swimming on Tuesday and
Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body plus
develop your heart and lungs.
The only way to increase the size and strength of your
muscles is to push them close to their maximum
capacity. When you progressively increase the intensi-
ty of your exercise, your muscles will continually adapt
and grow. You can tailor the individual exercise to the
proper intensity level in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions).
The proper amount of weight for each exercise obvi-
ously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
PERSONALIZING YOUR EXERCISE PROGRAM
Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very impor-
tant to avoid overdoing it during the first few months of
your exercise program. You should progress at your
own pace and be sensitive to your body’s signals. If
you experience pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
Find out what is wrong before continuing. Remember
that adequate rest and a proper diet are important
factors in any exercise program.
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
WORKING OUT
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group with
emphasis on the areas that you want to develop the
Cross Training
Many people desire a complete and well-balanced fit-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
most. To give balance and variety to your workouts,
vary the exercises from session to session.
• Rest three minutes after each set for a muscle build-
ing workout
• Rest one minute after each set for a toning workout
• Rest 30 seconds after each set for a weight loss
workout
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving through
the full range of motion for each exercise and moving
only the appropriate parts of the body. Exercising in
an uncontrolled manner will leave you feeling exhaust-
ed. On the exercise poster accompanying this manual,
you will find photographs showing the correct form for
several exercises. A description of each exercise is
also provided, along with a list of the muscles affect-
ed. Refer to the muscle chart below to find the loca-
tions of the muscles.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout is
very effective for increasing flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. The
chart on page 17 of this manual can be photocopied
and used to schedule and record your workouts. List
the date, the exercises performed, the weight plus the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end
of every month.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath!
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.
You should rest for a short period of time after each
set. The ideal resting periods are:
MUSCLE CHART
N
O
P
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
A
B
C
Q
R
D
E
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
G
M
H
I
U
V
Q. Triceps (back of arm)
J
K
W
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
R0999A
Part List - Model No. 831.150860
Key No.
Qty.
Description
Key No.
Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
6
1
2
4
1
1
1
2
1
Seat Bracket A
Leg Lever Lock
Leg Lever
Front Leg
Bench Frame
Left Base
Right Base
Left Upright
Right Upright
Curl Post
Weight Rest
Adjustment Tube
Backrest Tube A
Backrest Tube B
Seat Pin
Long Pad Tube
Short Pad Tube
Foam Pad
Seat Bracket B
Plastic Washers
M8 Washer
Seat
Backrest
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#
1
2
2
2
6
2
2
2
4
4
2
1
3
9
1
4
1
4
6
2
2
2
2
1
1
1
Front Leg Endcap
Support Plate
2” Square Inner Cap
1” Round Inner Cap
3/4” Round Inner Cap
1” Square Inner Cap
1 1/2” Square Inner Cap
1 1/4” Square Inner Cap
10mm Plastic Bushing
M6 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
M10 Washer
M8 x 58mm Bolt
M8 x 16mm Bolt
M8 Nylon Locknut
M10 x 70mm Bolt
M8 x 65mm Bolt
M10 x 175mm Bolt
M6 x 40mm Bolt
M6 x 16mm Screw
Outer Upright Bushing
M8 x 55mm Carriage Bolt
M8 x 60mm Bolt
M10 Nylon Locknut
1 3/4” Slotted Square Inner Cap
User’s Manual
Curl Pad
M10 Adjustment Knob
M8 Adjustment Knob
#
Exercise Chart
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
R0999A
Exploded Drawing - Model No. 831.150860
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
The model number and serial number of your WEIDER® PRO 208
Weight Bench are listed on a decal attached to the frame. See the
front cover of this manual to find the location of the decal.
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
QUESTIONS?
If you find that:
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
• you need help assembling or
operating the WEIDER® PRO 208
Weight Bench
• The MODEL NUMBER of the product (831.150860).
• The NAME of the product (WEIDER® PRO 208 Weight Bench).
• a part is missing
• or you need to schedule repair
service
• The KEY NUMBER and DESCRIPTION of the PART (see the
PART LIST/EXPLODED DRAWING at the center of this manual).
call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART
(1-800-366-7278)
Full 90 Day Warranty
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
Part No. 148210 H02137-C R0999A
Printed in China © 1998 SEARS, ROEBUCK AND CO.
Download from Www.Somanuals.com. All Manuals Search And Download.
|