OWNER’S MANUAL
20/15/10/2 AMP
FULLY AUTOMATIC
BATTERY CHARGER
Model No.
200.71
CAUTION:
Before first use of charger, read this manual, and
follow all its Safety and Operating Instructions with
every charger use.
Save these instructions.
Made in U.S.A. of U.S. and imported parts.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
600-198
Download from Www.Somanuals.com. All Manuals Search And Download.
1
IMPORTANT SAFETY INSTRUCTIONS
HELP US HELP YOU
Remember:
WARNING: To reduce the risk of
explosion, explosive gases, or injury
while using your battery charger, follow
the precautions listed below:
•
Place charger as far away from
battery being charged as the charger
cables will permit.
•
Read all instructions and cautions
printedonthebatterycharger,
battery,andvehicleorequipment
usingbattery.
•
•
Do not expose charger to rain or
snow.
Never charge a frozen battery. If
batteryfluid(electrolyte)becomes
frozen, bring battery into a warm area
to thaw before you begin charging.
•
Use charger only on lead-acid type
rechargeable batteries, such as
those used in cars, trucks, tractors,
airplanes,vans,RV’s,trolling
motors, etc. This charger is not
intended to supply power to a low
voltageelectricalsystem.
•
Never allow battery acid to drip on
charger when reading specific gravity
orfillingbattery.
•
•
Never set a battery on top of the
charger.
•
Use only attachments recommended
or sold by manufacturer. The use of
attachments not recommended
by the manufacturer may result in
fire, electric shock, or injury.
Never place charger directly above
battery being charged. The gases from
the battery will corrode and damage
thecharger.
•
•
Do not disassemble charger. Take
it to a qualified service professional
if service or repair is required. Incorrect
assembly may result in fire or
electricalshock.
•
Never use charger for charging
dry cell batteries that are commonly
used with home appliances like radios,
stereos, remote controls, etc. These
batteries may burst and cause
personalinjury.
To reduce risk of electrical shock,
unplug the charger from the outlet
beforeattemptinganymaintenance
orcleaning.
•
•
Never touch the battery clamps
together when the charger is on.
You will cause a spark.
•
•
Always charge battery in a well
ventilatedarea.
Never operate charger if it has
received a hard blow, been dropped, or
otherwise damaged. Take it to a
qualifiedprofessionalforinspection
andrepair.
Battery chargers get hot during
operation and must have proper
ventilation.Airneedstoflowaround
entirecharger.
•
•
Be sure to position the charger power
cord to prevent it from being stepped
on, tripped over, or damaged.
•
Do not set charger on flammable
materialslikecarpeting,upholstery,
paper, cardboard etc. Charger may
damage leather and melt plastic
andrubber.
Never pull out the plug by the cord
whenunpluggingthecharger.Pulling
on the cord may cause damage to the
cord or the plug.
•
Do not operate the charger if it has a
damaged power cord or plug. Have the
cordreplaced.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
PERSONALSAFETYPRECAUTIONS
For your own personal safety, please follow the following precautions:
•
Remove all personal metal items
from your body, such as rings,
bracelets, necklaces, and watches
whileworkingwithalead-acidbattery.
A battery can produce a short circuit
current high enough to weld a ring
•
Wear complete eye and clothing
protection when working with lead-
acidbatteries.
•
Be sure that someone is within range
of your voice to come to your aid if
needed while you work with or are near
alead-acidbattery.
(or the like) to metal, causing a severe
burn.
•
•
Have plenty of fresh water and soap
nearby for use in case battery acid
contacts your eyes, skin, or clothing. If
this happens, wash immediately with
soap and water. Then get medical
attention.
•
Take care not to drop any metal tool or
metal object onto the battery. This may
spark or short circuit the battery or
another electrical device that may
causeanexplosion.
•
•
Alwaysoperateyourbatterychargerin
anopen,wellventilatedarea.
Avoid touching your eyes while
working with a battery. Acid particles
(corrosion) may get into your eyes. If
this occurs, flush eyes immediately
with running cold water for at least 10
minutes. Then immediately get medical
attention.
Never smoke or allow a spark or
flame in the vicinity of the battery or
engine.Batteriesgenerateexplosive
gases.
•
Neutralize any acid spills thoroughly
with baking soda before attempting to
cleanup.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
BEFORE USING YOUR BATTERY CHARGER
It is important to understand your charger's requirements. This section will tell you
about your charger's electrical requirements and how to prepare a battery for
charging.
ASSEMBLING YOUR CHARGER
Included with your battery charger are
two cord wrap posts for storage of the
clamp cables.
To install, align the three tabs to
correspond with the three receptacles
and push until you hear a snap.
Wrap clamp cord after unplugging the
power cord and store your charger in a
dry location.
eat
USING AN EXTENSION CORD
PLUGGING IT IN
WARNING: ElectricalShockHazard.
Be sure that the power cord fits properly
intotheoutlet. Ifnot, haveaqualified
technicianinstallaproperoutlet. Never
alter the AC cord or plug provided.
The use of an extension cord is not
recommended. If you must use an
extension cord, please make sure
thatyoufollowtheseguidelines:
•
Make sure that the pins on charger's
power cord fit firmly into the extension
cord, and that the extension cord fits
firmly into the receptacle.
Improper connection can result in
electrical shock.
Your charger requires a 120V receptacle
installed according to all local codes and
ordinances.
•
•
Check that the extension cord is
properly wired and in good electrical
condition.
Make sure that the wire size is large
enough for its length and for the AC
ampere rating as specified in the chart
below.
MINIMUM RECOMMENDED EXTENSION CORD
Length of Cord, in Feet
25 50 100 150
18 16 12 10
AWG* Size of Cord
*AWG=American Wire Gauge
Download from Www.Somanuals.com. All Manuals Search And Download.
5
PREPARING YOUR BATTERY TO BE CHARGED
It is important that you read and follow these guidelines while you are preparing to
charge your battery.
such as removing or not removing
cell caps while charging, and
recommended rates of charge.
•
Make sure that you have a 12 volt or
24 volt lead-acid battery. Set the
selector switch to match the voltage
rating of the battery to be charged.
•
•
•
Wear safety glasses. See additional
"Personal Safety Precautions" on
page 4.
•
•
Clean the battery terminals. Be
careful to keep corrosion from
getting in or around your eyes.
Be sure that the area around the
battery is well ventilated while it is
being charged.
For batteries with removable cell
caps, if required by the manufac-
turer, add distilled water to each cell
until the battery acid reaches the
level recommended. This will help
purge excessive gases from the
cells. Be careful not to overfill. If you
have a sealed battery without cell
caps, no action is necessary.
If it is necessary to remove the
battery from the vehicle to charge it,
always remove the grounded
terminal from the battery first. Turn
off all vehicle accessories to avoid
sparks from occurring.
Continue to the next step listed below.
NOTE: A marine battery installed in a
boat must be removed and charged on
shore.
•
Take time to read all battery
manufacturer’s specific precautions,
USING YOUR BATTERY CHARGER
To obtain the best results from your battery charger, you must know how to use it
properly. This section will tell you how to set the controls, and how you can charge a
battery while it is still in the vehicle, or you can remove it and then charge it. Follow
the instructions below depending on how you choose to charge your battery.
SETTING THE CONTROLS
•
•
The center switch controls the type of
charge you want — AUTOMATIC,
MANUAL, or MAINTAINER.
All controls are located on the front of
the charger. Follow these instructions
to obtain the correct charge level for
your battery.
The switch on the lower right selects
the charge rate:
SELECTOR SWITCHES:
• 2 AMP charge for 12 VOLT
batteries/24 VOLT systems.
• 10 AMP charge for 12 VOLT
batteries/ 24 VOLT systems.
• 20 AMP for 12 VOLT batteries or
15 AMP for 24 VOLT systems. The
battery voltage selection (12 or 24
volt) will automatically determine
whether the 20 or the 15 amp
charge rate is used.
Your charger has four switches:
•
The switch on the top right is used to
select the type of battery being
charged — REGULAR, DEEP
CYCLE, or GEL CELL.
•
The switch on the left is used to select
the battery voltage— either 12 or 24
volt.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
seasonal farm equipment and the like.
Use after fully charging the
battery in one of the charging
positions.
Battery Type:
The charger is designed to provide a
specific charge best suited for charging
each type of battery. Charging a GEL
CELL battery as a REGULAR or DEEP
CYCLE battery can permanently
damage it. Charging a battery on
anything but the proper selection can
result in a partial charge or damaged
battery. DO NOT charge a Gel Cell on
any other setting but, Gel Cell.
MANUAL
L
AUTOMATIC
MAINTAINER
Charge Rate:
•
Use the 2 AMP charge rate when you
can afford the time. The lower the
charge rate, the longer it will take, but
the battery is subjected to much less
stress. Unless a Gel Cell battery
manufacturer recommends otherwise,
use the 2 AMP rate for charging.
DEEP CYCLE
L
REGULAR
GEL CELL
Battery Voltage:
•
•
Use the10 AMP 12/24 VOLT rate for
most common charging applications.
It provides the most complete charge
with the least stress on the battery.
Select the voltage of your battery. The
most common applications will be 12 volt,
but 24 volt battery systems are being
widely used in special applications.
Use the 20 AMP 12 VOLT rate when
speed is important. This rate is
selected when 12 VOLT is selected on
the Battery Voltage switch. It provides
a faster charge than the 10 AMP rate.
The 15 AMP 24 VOLT rate is selected
when 24 VOLT is selected on the
Battery Voltage switch.
12 VOLT
24 VOLT
Charge Type:
•
Use the MANUAL setting only if you
check the charging progress
10 AMP 12/24 VOLT
L
frequently. The charger will not stop
charging when the battery reaches
full charge, possibly damaging the
battery if left on too long. A severely
discharged battery may not have
enough charge to start the control
circuit in an automatic setting. In this
case, charge on MANUAL until the
battery has enough charge to accept
an Automatic setting.
2 AMP
12/24 VOLT
20 AMP 12 VOLT
15 AMP 24 VOLT
AMMETER:
The ammeter indicates the measure
amount of amperes being drawn by the
battery. When you first start charging a
battery, the reading will be high, with
the needle near 20 using the 20 amp
charging rate.
•
•
Use the AUTOMATIC setting for all
batteries and charge rates. The
charger will automatically stop
charging when the battery reaches full
charge and begin charging again when
battery requires.
•
In the MANUAL setting, as the battery
charges, the needle will fall to about 8
or 10 amps, indicating a charged
battery.
Use the MAINTAINER to maintain a
charge in batteries stored for long
periods, such as those in RVs,
•
In both AUTOMATIC settings, the meter
needle will fall to zero when the battery
has completed the charging cycle. A
Download from Www.Somanuals.com. All Manuals Search And Download.
7
freshly charged battery’s voltage will
drop shortly after charging stops, and
the charger, if left connected, may
resume charging. This off-and-on
cycling will continue until the battery’s
voltage no longer drops enough to
restart the charger.
CHARGING YOUR BATTERY
Chargingyourbatteryinsidethe
vehicle:
1. Arrange the power cord and charging
leads carefully in order to avoid
damage that could be caused by the
hood, door, or moving engine parts.
•
At the 2 amp charging rate you will
notice very little needle movement.
2. Keep clear of the fan blades, belts,
pulleys, and other parts that can cause
injury.
3. Check the polarity of the battery posts
using the identification marks on the
battery case: POSITIVE (POS, P, +)
and NEGATIVE (NEG, N, -). NOTE:
The positive post on top-post batteries
is usually larger than the negative post.
4. Identify which battery post is the
ground or connected to the chassis.
THE NEGATIVE POST IS
NORMALLY THE ONE THAT IS
GROUNDED.
LED INDICATORS:
Two LED INDICATORS provide
information on the state-of-charge by
glowing steadily or blinking at different
intervals.
5. To charge a negative grounded
post system: Connect the red
(POSITIVE) charger clamp to the
ungrounded POSITIVE (POS, P, +)
post of the battery. Rock or twist the
clamps back and forth to make a solid
connection. Next, connect the black
(NEGATIVE) clamp to a heavy
GREEN, FAST BLINK:
When the charger is charging a battery,
the green LED indicator will blink rapidly.
GREEN, STEADY GLOW:
In all settings, the green LED indicator
will glow when the charging cycle is
complete. In the MANUAL setting, stop
charging when the green LED indicator
glows steadily.
unpainted metal part of the chassis or
engine block, away from the battery.
DO NOT connect clamp to carburetor,
fuel lines, or sheet metal parts. (See
Figure A.)
To charge a positive grounded post
system: Connect the black
(NEGATIVE) charger clamp to the
NEGATIVE (NEG, N, -) ungrounded
post of the battery. Then connect the
red (POSITIVE) clamp to a heavy
unpainted metal part of the chassis or
engine block, away from the battery.
DO NOT connect clamp to carburetor,
fuel lines or sheet metal parts.
GREEN, SLOW BLINK:
A slowly blinking green LED indicates that
the charger is maintaining the battery’s
state of charge in the MAINTAINER mode.
RED, STEADY GLOW:
When the red LED indicator glows
steadily, it means that the charger has not
sensed a battery voltage. The leads may
be reversed on the posts, or one or both
connections may not be making solid
contact. Check your connections.
IMPORTANT: Wear safety glasses
and turn face away from the battery
when making connections.
RED, SLOW BLINK:
The charger has sensed a battery
condition which prevents further charging.
Have the battery checked by a Sears
technician.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
POSITIVE (POS, P, +) and NEGATIVE
(NEG, N, -). NOTE: On top-post
batteries, the positive battery terminal
usually has a larger diameter than the
negative one.
3. Connect the red (POSITIVE) charger
clamp to the POSITIVE post of the
battery. Be sure to rock the clip back
and forth to make a solid connection.
4. Attach a 6-gauge (AWG) or a 4-gauge
(SAE) insulated battery cable of at
least 24-inches long to the NEGATIVE
battery post. This cable will provide a
safer connection if arcing and sparking
occur, it will be at a distance from the
battery. NOTE: The battery cable is
not provided with the charger, but may
be purchased at most automotive
stores.
NEGATIVEGROUNDEDSYSTEM
Figure A
6. Set the Selector Switches to the
desired settings. (See “Setting the
Controls” on page 6.)
7. Plug the power cord into an AC outlet.
The green LED indicator should blink
rapidly to indicate that the battery is
being charged.
5. Take the other end of the 6-gauge
(AWG) or a 4-gauge (SAE) insulated
24-inch cable and, standing as far
away from the battery as possible,
connect the black (NEGATIVE) lead to
the free end of the cable. Rock the
clamp to make a solid connection.
IMPORTANT: Wear safety glasses
and face away from the battery while
making the final connection.
8. When the battery is fully charged, the
green LED indicator will glow steadily.
• If an AUTOMATIC setting is used,
the charger will automatically stop
charging.
• If a MANUAL setting is used, you
must monitor the charging and stop
the charger manually.
6. Set the Selector Switches to the
desired settings. (See “Setting the
Controls” on page 6).
9. When the battery is fully charged, first
unplug the charger power cord. Then,
standing away from the battery,
remove the charger clamp from the
chassis first, then from the battery
post.
7. Plug the power cord into an AC outlet.
The green LED indicator should blink
rapidly to indicate that the battery is
being charged.
8. When the battery is fully charged, the
green LED indicator will glow steadily.
10. Clean and store the battery charger in
a dry location.
• If an AUTOMATIC setting is used,
the charger will automatically stop
charging and will restart if battery
voltage drops too low.
Charging your battery
outside the vehicle:
1. Remove the battery from vehicle,
making sure to disconnect grounded
terminal first with all power turned off
to the vehicle.
• If a MANUAL setting is used, you
must monitor the charging and
stop the charger manually.
9. When the battery is fully charged,
unplug the charger power cord.
2. Check the polarity of the battery posts
as indicated on the battery case:
Download from Www.Somanuals.com. All Manuals Search And Download.
9
10. Standing away from the battery,
remove the negative lead from the
insulated cable connected to the
NEGATIVE post first. Then remove
the lead from the POSITIVE post.
POSITIVE
BATTERY
NEGATIVE
R
+
-
11. Clean and store the battery charger
in a dry location.
POWER
CORD
GROUNDED
POWER
OUTLET
Figure B
Download from Www.Somanuals.com. All Manuals Search And Download.
10
CALCULATING CHARGE TIME
Battery Rating Method
Use the following table to more accurately determine the time it will take to fully
charge a battery that is initially at 50% State-of-Charge. Identify your battery type and
its associated Charge Time in the table. Common battery types are:
•
•
•
Small batteries, motorcycles, garden tractors, etc., are usually rated in Amp-Hours
(AH).
Car and truck batteries, usually rated in Reserve Capacity (RC), Cold Cranking
Amps (CCA), or both.
Marine, or deep cycle batteries, usually rated in either Amp-Hours or Reserve
Capacity (RC).
•
•
NR means the charger setting is NOT RECOMMENDED.
NA means not allowed. DO NOT charge at this setting
Charge Time Table for Batteries at 50% State-of-Charge
Battery Rating
Charge-Time(Hours)
Battery
Type
AH
CCA
RC
10 AMP 15 AMP 20 AMP
2AMP
2 - 4
6 - 12
12 - 32
NA
NA
NA
NA
1 - 2
2 - 3
3 - 7
3
NA
NA
Motorcycle
and tractor
4 - 10
8 - 11
¾ - 1
1 - 1½
1½ - 3½
1½
1 - 1½
1½ - 2
2 - 5
2
200 - 315
40 - 60
Car and
Truck
315 - 550 11 - 16
60 - 85
16 - 35
15
85 -190 550 - 1000
40
80
80
2½
5
3½
26
140
160
180
390
650
Marine and
Deep Cycle
95
3
6
4
30
105
40
3½
7
4½
33
NR
6
NR
NR
20
Gel Cell
80
NR
10
32
Voltmeter Method
To find the time needed to fully charge your battery, determine the battery’s charge
level with a voltmeter or electronic State-of-ChargeTester. Use the table below to
convert Voltmeter and State-of-Charge readings at room temperature to the appro-
priate Charge Factor. Then use the formulas that follow the table to determine the
approximate Charge Time.
Charge Factor Table
Voltmeter Reading
State-of-Charge
Reading
100%
75%
Charge Factor
12 Volt Battery
12.67
24 Volt Battery
25.34
0
12.45
24.90
0.25
0.50
24.50
12.25
12.03
11.86
50%
24.06
23.72
25%
0.75
1
100%
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Charge Time Needed if Amp-Hours is Known
•
•
•
•
Find the Charge Factor for your battery in the table on page 11.
Multiply by the Amp-Hour rating of the battery.
Divide by the Charger Setting (either 2 Amp, 10 Amp or 20 Amp).
Multiply by 1.25 to get the approximate Hours Needed to bring the battery to full
charge.
Example: 15 Amp-Hour (AH) Battery, 50% State-of-Charge,
2 Amp Charger Setting
[(AH x Charge Factor) ÷ Charger Setting] x 1.25 = Hours Needed
(15 x 0.5 ÷ 2) x 1.25 = 4.7 Hours
Charge Time Needed if Reserve Capacity is Known
•
•
•
•
Find the Charge Factor for your battery in the table on page 11.
Multiply by the Reserve Capacity rating of the battery.
Divide by the Charger Setting (either 2 Amp, 10 Amp or 20 Amp).
Multiply by 0.73 to get the approximate Hours Needed to bring the battery to
full charge.
Example: 95-Minute Reserve Capacity (RC) Battery, 25%
State-of-Charge, 20 Amp Charger Setting
[(RC x Charge Factor) ÷ Charger Setting] x 0.73 = Hours Needed
[(95 x 0.75) ÷ 20] x 0.73 = 2.6 Hours
MAINTENANCE AND CARE
To keep your battery charger working properly for years:
1. Clean the clamps each time you are
finished charging. Wipe off any
battery fluid that may have
2. Coil the input and output cords
neatly when storing the charger.
This will help prevent accidental
damage to the cords and charger.
come in contact with the clamps to
prevent corrosion.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
TROUBLESHOOTING
Performance problems often result from little things that you can fix yourself. Please
read through this chart for a possible solution if a problem occurs.
PROBLEM
POSSIBLE CAUSE
SOLUTION/REASON
Clamps not making good Check for poor connection at battery. Make
No ammeter reading.
connection.
sure clamps and posts are clean. Battery
may not accept an AUTOMATIC charge if
severely discharged. Use MANUAL setting,
see "Using Your Battery Charger" on page 6.
2-amp charge rate.
Ammeter needle will indicate little activity at
the 2-amp charge rate.
No AC power reaching
charger.
Check AC outlet and extension cords for
loose fitting plug.
Check for open fuse or circuit breaker
supplying AC outlet.
Shorted battery clamps.
Shorted battery.
Circuit breaker in
charger cycles on
and off with a
clicking sound in the
MANUAL setting.
Separate the clamps. Circuit breaker cycles
when current draw is too high.
Check for worn cables and replace if
needed.
Charger leads reversed
on battery.
Have a Sears technician test the battery.
Correct connections.
Ammeter reads less
than selected charge
rate when charging.
Extension cord too long
or gauge too small.
Use shorter or heavier extension cord.
Battery has weak cell or Sulfated battery will eventually take a
sulfated plate.
normal charge if left connected. If the
battery will not take a charge, have it
tested by a Sears technician.
Battery is partially
charged.
Continue charging battery.
Charger makes a
loud buzz or hum.
Transformer laminations
vibrate (buzz).
Continue charging. Buzz is not abnormal.
Continue charging battery for another two
hours. If problem continues, consult a
qualified technician.
Ammeter needle
stays at the right
side of the meter.
Battery severely
discharged.
Make sure size selection is in proper 12 or
24 volt position.
Battery size selector
switch in the wrong
position
If the above solutions do not eliminate the problem...call toll-free
from anywhere in the U.S.A. 1-800-SEARS-64 • (1-800-732-7764)
7 AM to 4:30 PM CST Monday through Friday
Download from Www.Somanuals.com. All Manuals Search And Download.
13
PARTS
This section shows an illustration of your battery charger. Use it to become familiar
with where all the parts are located, and what they look like.
Replacement Parts List Model 713201
Part Number
93026487
Description
Handle
Item Description
Item
7
Part Number
3599000270
0499000060
5399100095
0899001078
0000000600
1199004390
Transformer
1
2
3
4
5
6
2299000992
2299000991
3999000089
3899000738
90026116
Switch - left DPDT
Meter
SCRcontrolModule
PC Board Asm (SWITCHES)
CircuitBreaker
8
9
Faceplate
10
11
12
Owner'sManual
Cord Wrap Cleats
OutputCord
ACPowercord
Download from Www.Somanuals.com. All Manuals Search And Download.
14
WIRINGDIAGRAM
Download from Www.Somanuals.com. All Manuals Search And Download.
15
For information about troubleshooting
Call toll-free from anywhere in the U.S.A.
7 am to 4:30 pm CST Monday through Friday
1-800-732-7764
For the repair or replacement
parts you need
Call 7 am - 7 pm, 7 days a week
1-800-366-PART
(1-800-366-7278)
For the location of an authorized
Sears Service Center in your area
Call 24 hours a day, 7 days a week
1-800-488-1222
When requesting service or
ordering parts, always provide
thefollowinginformation:
• Product Type: 20/15/10/2 AMP
Fully Automatic Battery Charger
• ModelNumber:200.713201
• Part Number (See Page 14)
• Part Description (See Page 14)
Download from Www.Somanuals.com. All Manuals Search And Download.
16
|