Sears Battery Charger 20071210 User Guide

OWNER’S  
MANUAL  
Model No.  
200.71210  
10/2 AMP  
MANUAL  
BATTERY CHARGER  
CAUTION:  
Read and Follow All Safety  
Rules and Operating Instructions  
Before Every Use of this Product.  
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
– SAVE THESE INSTRUCTIONS –  
w
To reduce the risk of explosion, explosive gases, or injury while  
using your battery charger, follow the precautions listed below:  
L! WARNING  
Read all instructions and cautions printed  
on the battery charger, battery, and vehicle or  
equipment using battery.  
Do not disassemble charger. Take it to a  
qualified service professional if service or  
repair is required. Incorrect assembly may  
result in fire or electrical shock.  
To reduce risk of electrical shock, unplug  
the charger from the outlet before attempting  
any maintenance or cleaning.  
Use charger only on lead-acid type re-  
chargeable batteries, such as those used in  
cars, trucks, tractors, airplanes, vans, RV’s,  
trolling motors, etc. This charger is not in-  
tended to supply power to a low voltage  
electrical system other than in an automotive  
application.  
Always charge battery in a well ventilated  
area.  
Use only attachments recommended or  
sold by manufacturer. The use of attachments  
not recommended by the manufacturer may  
result in fire, electric shock, or injury.  
Help us help you  
Remember:  
Place charger as far away from battery being  
charged as the charger cables will permit.  
Do not expose charger to rain or snow.  
Never charge a frozen battery. If battery fluid  
(electrolyte) becomes frozen, bring battery into a  
warm area to thaw before you begin charging.  
Never allow battery acid to drip on charger when  
reading specific gravity or filling battery.  
Never touch the battery clamps together when the  
charger is energized.  
Never operate charger if it has received a hard blow,  
been dropped, or otherwise damaged. Take it to a  
qualified professional for inspection and repair.  
Be sure to position the charger power cord to  
prevent it from being stepped on, tripped over, or  
damaged.  
Never set a battery on top of the charger.  
Never pull out the plug by the cord when unplug-  
ging the charger. Pulling on the cord may cause  
damage to the cord or the plug.  
Never place charger directly above battery being  
charged. The gases from the battery will corrode  
and damage the charger.  
Do not operate the charger if it has a damaged  
power cord or plug. Have the cord replaced.  
Never use charger for charging dry-cell batteries  
that are commonly used with home appliances.  
These batteries may burst and cause personal  
injury.  
Personal Safety Precautions  
For your own personal safety, please follow the  
following precautions:  
Wear complete eye and clothing protection when  
working with lead-acid batteries.  
Remove all personal metal items from your body,  
such as rings, bracelets, necklaces, and watches  
while working with a lead-acid battery. A battery can  
produce a short circuit current high enough to weld  
a ring (or the like) to metal, causing a severe burn.  
Be sure that someone is within range of your  
voice  
to come to your aid if needed while you work  
with or are near a lead-acid battery.  
Take care not to drop any metal tool or metal object  
onto the battery. This may spark or short circuit the  
battery or another electrical device that may cause  
an explosion.  
Have plenty of fresh water and soap nearby for  
use in case battery acid contacts your eyes, skin,  
or cloth-ing. If this happens, wash immediately  
with soap and water. Then get medical attention.  
Avoid touching your eyes while working with a  
battery. Acid particles (corrosion) may get into  
your eyes. If this occurs, flush eyes immediately  
with running cold water for at least 10 minutes.  
Then immediately get medical attention.  
Always operate your battery charger in an open, well  
ventilated area.  
Never smoke or allow a spark or flame in the vicinity  
of the battery or engine. Batteries generate explosive  
gases.  
Neutralize any acid spills thoroughly with baking  
soda before attempting to clean up.  
2
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are  
located, and what they look like.  
Replacement Parts List Sears 71210  
Item Description  
Part Number  
3799001402  
2299000825  
3799001382  
90026058  
1
2
3
4
5
6
7
8
Cover  
Heatsink/Diode Assembly  
Base  
AC Power Cord  
Transformer  
93026336  
Output Cable  
3899000016  
3999000045  
2299000248  
0399000007  
0399000008  
5399100091  
0499000032  
3799001392  
0899000531  
3599000240  
5181806256  
Circuit Breaker (20A)  
50A Clamp (1)  
Sleeving Red (2) required  
Sleeving Black (2) required  
Meter  
9
10  
11  
12  
13  
14  
15  
Switch SPDT  
Front Panel  
Decal  
Handle  
Screw 8-18 x 3/8" (4)  
Owner's Manual and Parts List (Not Shown) 0000000509  
Wiring diagram  
3
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using Your Battery Charger  
It is important to understand your charger's requirements. This section will tell you about your charger's electrical  
requirements and how to prepare a battery for charging.  
Plugging it in  
L! WARNING  
Electrical Shock Hazard  
Be sure that power cord fits properly into outlet.  
If not, have a qualified technician install a proper  
outlet. Never alter the AC cord or plug provided.  
Improper connection can result in electrical shock.  
Your charger should be grounded to reduce the risk  
of electrical shock.  
Your charger is equipped with an electrical cord that  
has an equipment grounding conductor and a ground-  
ing plug designed to be used on a 120 volt circuit. The  
plug must be plugged into an outlet that has been  
properly installed and grounded in accordance with all  
local codes and ordinances.  
A TEMPORARY adapter may be used to connect the  
charger to a two-pole outlet if a properly grounded  
outlet is not available. Use the adapter ONLY until a  
properly grounded outlet can be installed by a qualified  
electrician.  
DANGER: Before using an adapter as illustrated, be  
certain that the center screw of the outlet plate is  
grounded. The green colored grounding clip of the  
adapter must be attached by a screw to a properly  
grounded outlet. If unsure whether outlet is properly  
grounded, contact a professional electrician. If neces-  
sary, replace the original outlet cover screw with a  
longer one that will secure the grounding clip to the  
outlet cover and make a ground connection to the  
grounded outlet.  
Using an extension cord  
The use of an extension cord is not recommended. If  
you must use an extension cord, please make sure  
that you follow these guidelines:  
MINIMUM RECOMMENDED EXTENSION CORD  
Make sure the pins on the plug of the extension cord  
are the same number, size, and shape as those of the  
plug on the charger.  
Use only 3-conductor (grounded) extension cord  
when necessary.  
Length of Cord, in Feet 25  
50  
18  
100  
16  
150  
14  
AWG* Size of Cord  
18  
*AWG=American Wire Gauge  
Check that the extension cord is properly wired and  
in good electrical condition.  
Make sure that the wire size is large enough for its  
length and for the AC ampere rating as specified in  
the accompanying chart.  
4
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing your battery to be charged  
It is important that you read and follow these guidelines  
while you are preparing to charge your battery.  
• Make sure that you have a 12 volt lead-acid battery.  
• Clean the battery terminals. Be careful to keep  
corrosion from getting in or around your eyes.  
• If you have a battery with removable cell caps, if  
required, add distilled water to each cell until the  
battery acid reaches the level recommended by the  
manufacturer. This will help purge excessive gases  
from the cells. Be careful not to overfill. If you have a  
sealed battery without cell caps, no action is neces-  
sary. Continue to the next step listed below.  
• Take time to read all battery manufacturer’s specific  
precautions, such as removing or not removing  
cell caps while charging, and recommended rates  
of charge.  
• Wear safety glasses. See additional "Personal Safety  
Precautions" on page 2.  
• Be sure that the area around the battery is well  
ventilated while it is being charged. If ventilation is  
poor, gas can be manually blown away by using a  
piece of cardboard or other non-metallic material as  
a fan.  
• If it is necessary to remove the battery from the  
vehicle to charge it, always remove the grounded  
terminal from the battery first. A spark may be  
caused if all accessories in the vehicle are not  
completely turned off.  
NOTE: A marine battery installed in a boat must be  
removed and charged on shore.  
5
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Your Battery Charger  
For best results from your battery charger, learn to use it properly. This section tells how to set the controls and how  
to charge a battery in or out of the vehicle.  
Setting the Controls  
SELECTOR SWITCHES:  
A 2-way switch is used to select the 2-AMP or the  
10-AMP charge rate.  
L
10 AMP  
L
2 AMP  
AMMETER:  
The AMMETER indicates the measured amount of amperes  
being drawn by the battery. When you first start charging a  
battery, the reading will be high, with the needle near 10 using  
the 10 amp charging rate. As the battery charges, the needle  
will fall to about 4 or 5 amps, indicating a charged battery.  
At the 2 amp charging rate, as the battery charges the  
needle will fall to about 3/4 to 1 amp indicating a charged  
battery.  
The percent of charge scale is intended as a visual aid to  
help simplify reading the state of charge of the battery. The  
meter is scaled for use with the 10 amp charge rate only.  
For the 2 amp charge rate use the red triangle. The percent  
of charge is based on current drawn by the battery. For this  
reason accuracy will vary with the size and battery type.  
Charging Your Battery  
Charging a battery in the vehicle:  
1. Arrange the power cord and charging leads carefully  
to avoid damage that could be caused by the hood,  
door, or moving engine parts.  
2. Keep clear of fan blades, belts, pulleys, and other  
parts that can cause injury.  
3. Check the polarity of the battery posts as indicated  
on the battery case: POSITIVE (POS, P, or +) and  
NEGATIVE (NEG. N or -). NOTE: The positive post  
on top-post batteries is usually larger than the  
negative post.  
4. Identify which battery post is ground or connected  
to the chassis. THE NEGATIVE POST IS  
NORMALLY THE ONE THAT IS GROUNDED.  
5. To charge a negative grounded post system:  
Connect the red (POSITIVE) battery charger clamp  
to the ungrounded POSITIVE (POS, P, +) post of the  
battery. Then connect the black (NEGATIVE) clamp  
to a heavy, unpainted metal part of the chassis or  
engine block, away from the battery. Do not connect  
clamp to carburetor, fuel lines, or sheet metal parts.  
To charge a positive grounded post system:  
Connect the black (NEGATIVE) battery charger  
clamp to the NEGATIVE (NEG, N, -) ungrounded  
post of the battery. Then connect the red  
NEGATIVE GROUNDED SYSTEM  
(POSITIVE) clamp to a heavy, unpainted metal part  
of the chassis or engine block. Do not connect  
clamp to carburetor, fuel lines, or sheet metal parts.  
IMPORTANT: Wear safety glasses and face away  
from the battery while making connections.  
6
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Connect the clamp to the battery post and twist or  
rock back and forth to make a solid connection.  
This will help keep the clamps from slipping off the  
posts and causing sparks.  
7. Select the charge rate with the Selector Switch then  
plug the power cord into a grounded AC outlet to  
begin charging.  
8. The charger will not stop when the battery is fully  
charged. For this reason it is important to check  
charging progress frequently. Overcharging can  
damage a battery, you must monitor and unplug  
charger when battery is fully charged.  
9. When the battery is fully charged, the AMMETER  
pointer will fall to about half the charge rate selected.  
For specific positions, refer to the "Ammeter" section  
in “Using your battery charger" on page 6.  
10. When the battery is fully charged, unplug the charger  
power cord before attempting to disconnect charger  
clamps.  
11. Standing away from the battery, remove the charger  
clamps in this order: (1) from the chassis  
connection and, (2) from the battery post or terminal.  
12. Clean and store the battery charger in a dry location.  
Charging your battery outside the vehicle:  
1. Remove the battery from vehicle, making sure to  
disconnect grounded terminal first with all accessories  
and lights turned off in the vehicle.  
2. Check the polarity of the battery posts as indicated  
on the battery case: POSITIVE (POS, P, +) and  
NEGATIVE (NEG, N, -).  
NEGATIVE  
POSITIVE  
NOTE: On top-post batteries, the positive battery  
terminal usually has a larger diameter post than the  
negative one.  
RGER  
BATTER
3. Connect the red (POSITIVE) charger clamp to the  
POSITIVE post of the battery. Be sure to rock the  
clip back and forth to make a solid connection.  
4. Attach a 6-gauge (AWG) or a 4-gauge (SAE)  
insulated battery cable of at least 24-inches in length  
to the NEGATIVE battery post. This cable will provide  
a safer connection because arcing and sparking will  
occur away from the battery. (The battery cable is  
not provided with the charger, but may be purchased  
at most automotive accessory outlets.)  
POWER  
CORD  
TO  
GROUNDED  
POWER  
OUTLET  
5. Take the other end of the 6-gauge (AWG) or a 4-gauge  
(SAE) insulated 24-inch cable and, standing as far  
away from the battery as possible, connect the black  
(NEGATIVE) lead of the charger to the free end of the  
cable. Rock the clamp to make a solid connection.  
IMPORTANT: Wear safety glasses and face away  
from the battery while making this final connection.  
6. Select the rate of charge with the Selector Switch  
then plug the power cord into a grounded AC outlet  
to begin charging.  
7. The charger will not stop when the battery is fully  
charged. For this reason it is important to check  
charging progress frequently. Overcharging can  
damage a battery, you must monitor and unplug  
charger when battery is fully charged.  
8. When the battery is fully charged, the AMMETER  
pointer will fall to about half the charge rate  
selected. For specific positions, refer to the  
“Ammeter” section in “Using your battery charger”  
on page 6.  
9. When the battery is fully charged, unplug the  
charger power cord before attempting to  
disconnect charger clamps.  
10. Stand away from the battery and remove the  
charger leads from the NEGATIVE connection first,  
then from the POSITIVE battery post or terminal.  
11. Clean and store the battery charger in a dry location.  
7
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Calculating charge time  
The Chart Method  
Use the following table to more accurately determine  
the time it will take to bring a battery to full charge.  
First, identify where your battery fits into the chart.  
• Small batteries — motorcycles, garden tractors, etc.  
— are usually rated in Ampere Hours (AH). For  
example; 6 to 12 AH, or 12 to 32 AH.  
• Marine, or deep-cycle batteries are usually rated in  
Reserve Capacity (RC).  
NR means that the charger setting is NOT  
RECOMMENED.  
Find your battery’s rating on the chart below and note  
the charge time given for each charger setting.  
The times given are for batteries with a 50-percent  
charge prior to recharging. Add more time for severely  
discharged batteries.  
• Batteries in cars and smaller trucks are usually rated  
in Reserve Capacity (RC), Cold-Cranking Amps  
(CCA), or both.  
CHARGE RATE/CHARGING TIME - HOURS  
BATTERYSIZE/RATING  
2 AMP  
2 - 4  
4 - 10  
11 - 14  
14 -18  
18 - 35  
18  
10 AMP  
NR  
Motorcycle, garden  
tractor, etc.  
6 - 12 AH  
12 - 32 AH  
40 - 60 RC  
60 - 85 RC  
85 -190 RC  
80 RC  
SMALL  
BATTERIES  
NR  
2 - 27/8  
27/8 - 33/4  
33/4 - 7  
31/2  
200 - 315 CCA  
315 - 550 CCA  
550 - 1000 CCA  
CAR/TRUCKS  
MARINE/DEEPCYCLE  
140 RC  
27  
51/2  
160 RC  
30  
6
180 RC  
33  
7
The Hydrometer or Electronic Method  
To find the time needed to fully charge your battery,  
determine the battery’s charge level with a hydrometer  
or electronic Percent-of-Charge Tester. The following  
table will help you convert hydrometer readings to  
percent of charge values.  
To calculate time needed for a charge:  
Find the percent of charge needed. (A battery at  
50 percent charge that will be charged to 100  
percent needs another 50 percent (.50).  
Multiply the Amp Hour rating by the charge  
needed (.50) and divide by the charger setting  
(2 or 10 amps).  
Multiply the result by 1.25 and you’ll have the  
approximate time needed, in hours, to bring the  
battery to full charge.  
SPECIFIC  
GRAVITY  
PERCENT  
OF CHARGE  
PERCENT OF  
CHARGE NEEDED  
Add one additional hour for a deep-cycle battery.  
1.265  
1.225  
1.155  
1.120  
100%  
75%  
25%  
0%  
0%  
25%  
75%  
100%  
Example:  
Amp Hour Rating x charge needed x 1.25 = hours  
Charger Setting  
of  
charge  
100 (AH Rating) x .50 (charge needed) x 1.25 = 6.25  
When you know the percent of charge and the Amp  
Hour (AH) rating of your battery, you can calculate the  
approximate time needed to bring your battery to a full  
charge.  
10 (Charger Setting)  
hours  
100 x .50 = 5 x 1.25 = 6.25  
10  
To convert Reserve Capacity to Amp Hours, divide  
Reserve Capacity by 2, and add 16:  
You would need to charge your 100-Ampere Hour Bat-  
tery for approximately 6¼ hours at the 10-Amp charge  
rate using the above example.  
Amp Hours = Reserve Capacity + 16  
2
8
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance and care  
A minimal amount of care can keep your battery  
charger working properly for years.  
1. Clean the clamps each time you are finished  
charging. Wipe off any battery fluid that may have  
come in contact with the clamps to prevent  
corrosion.  
2. Coil the input and output cords neatly when  
storing the charger. This will help prevent acci-  
dental damage to the cords and charger.  
3. Occasional cleaning of the case of the charger  
with a soft cloth will keep the finish shiny and help  
prevent corrosion.  
9
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Performance problems often result from little things that you can fix yourself. Please read through this chart for a  
possible solution if a problem occurs.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION/REASONS  
No ammeter reading.  
Clamps not making good Check for poor connection at battery. Make sure clamps  
connection.  
and posts are clean.  
Ammeter needle will indicate little activity at the 2-amp charge  
rate.  
2-amp charge rate.  
No AC power reaching  
charger.  
Check AC outlet and extension cords for loose fitting plug.  
Check for open fuse or circuit breaker supplying AC outlet.  
Shorted battery clamps.  
Circuit breaker in  
charger cycles on and  
off with a clicking  
sound.  
Separate the clamps. Circuit breaker cycles when current  
draw is too high.  
Check for worn cables and replace if needed.  
Shorted battery.  
Have a Sears technician test the battery.  
Correct connections.  
Charger leads reversed  
on battery.  
Ammeter reads less  
than selected charge  
rate when charging.  
Extension cord too long or Use shorter or heavier extension cord.  
wire gauge to small.  
Sulfated battery will eventually take a normal charge if left  
Battery has weak cell or  
sulfated plate.  
connected. If the battery will not take a charge, have it  
tested by a Sears technician.  
Continue charging battery.  
Battery is only partially  
discharged.  
Continue charging. Buzz is not abnormal.  
Have charger tested by qualified technician.  
Transformer laminations  
vibrate (buzz).  
Charger makes a loud  
buzz or hum.  
Shorted diode (hum).  
If the above solutions do not eliminate the problem...  
call toll-free from anywhere in the U.S.A.  
1-800-SEARS-64  
(1-800-732-7764)  
7 AM to 4:30 PM CST Monday through Friday  
10  
Sears 210 - Sch 50911/13/95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10/2 AMP  
MANUAL  
BATTERY CHARGER  
OWNER’S  
MANUAL  
Model No.  
200.71210  
For information about troubleshooting  
Call toll-free from anywhere in the U.S.A.  
7 am to 4:30 pm CST Monday through Friday  
1-800-SEARS-64  
(1-800-732-7764)  
For the repair or replacement  
parts you need  
Call 7 am - 7 pm, 7 days a week  
1-800-366-PART  
(1-800-366-7278)  
For the location of a Sears Repair  
Service Center in your area  
Call 24 hours a day,  
7 days a week  
1-800-488-1222  
When requesting service or  
ordering parts, always provide  
the following information:  
Product Type  
Model Number  
Part Number  
REPAIR SERVICES  
America's Repair Specialists  
Part Description  
0000000509-895  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Quantum Data Projector 822S User Guide
Radio Shack Radio 12 888 User Guide
RCA Flat Panel Television PR42300 User Guide
ResMed Respiratory Product S8 AutoScore II User Guide
Roland Electronic Keyboard At 20s User Guide
Rosewill Network Card RC 303 User Guide
Samsung All in One Printer ML 1650 User Guide
Samsung Range FCQ321HTUB User Guide
Sangean Electronics Stereo Receiver DT400W User Guide
Sanus Systems Indoor Furnishings SFV49 User Guide