Instruction Manual
DC250
Digital Underwater
Camera Set
D
I
G
I
T
A
L
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation
Note: This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
E
I Reorient or relocate the receiving antenna.
I Increase the separation between the equipment and receiver.
I Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
I Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of
Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you
could be required to stop operation of the equipment.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
MUST DO
1. Read warnings in manual (pages 6-8).
•Always use freshly charged batteries.
Batteries can discharge at room
temperature up to 10% per day.
Store batteries in plastic bag or con-
tainer in refrigerator or cool, dry
place.
2. If you have any questions after reading
this manual or problems regarding the
SeaLife digital camera, housing or
accessories follow these instructions:
Do not contact dealer; do this:
•Check trouble shooting guide in this
manual or on the SeaLife website
•If this does not solve the problem
contact SeaLife Customer Service:
USA (856) 866-9192. For other
countries, contact the Sealife national
distributor. For a complete list, see
the above website.
4. Use only the following brands
Compact Flash memory cards:
•SanDisk, Kingston, Lexar, Panasonic,
PYN, Ritek and Pretec (registered
trademarks of respective companies).
5. Keep main O-Ring and housing
perfectly clean.
•Clean housing and main O-ring with
fresh water after every use.
•Do not remove O-ring. Do not
grease.
E
3. Use only the following AA batteries:
•SeaLife Nickel Metal Hydride (Ni-MH)
1800mAh or higher rechargeable
batteries. Carefully follow charging
instructions.
•Store camera and housing only after
careful cleaning and when totally dry.
6. Never let any moisture or dirt get
inside housing when opening.
•Only open and load the housing in
dry cool air, such as inside an air-
conditioned room.
•Lithium non-rechargeable batteries.
Lithium batteries last the longest of
all batteries but they are expensive
and they are not rechargeable.
•We do not recommend using Alkaline
batteries due to their short battery
life, however new high-energy alka-
line batteries, like Duracell Ultra, have
a longer battery life and can be used
with the SeaLife digital camera. Even
high-energy alkaline batteries do not
last as long as SeaLife Ni-MH
batteries. Do not use standard alka-
line batteries.
•Replace batteries when battery
power status indicator on camera is
down one bar.
•Turn camera power or LCD monitor
OFF when not using camera to
preserve battery power.
7. For good underwater pictures you
need:
•Clear water conditions.
•Control your buoyancy before taking
picture.
•Get as close as possible to subject
(ideal distance is 2’ to 6’).
•Make it a habit to use the SeaLife
Macro Lens/Filter for superb details
and vibrant colors.
•For best underwater pictures, use
External Flashes and snap-on Macro
or wide-angle lenses.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
This product will be replaced or repaired free of charge within 1 year from the purchase
date in the case of a manufacturing defect, if the complete defective product is sent freight
prepaid at the sender’s risk with prepayment for handling and shipping of US$10.00 to:
Pioneer Research, Attn: SeaLife Service Center, 97 Foster Road, Suite 5, Moorestown, NJ
08057, or to the SeaLife distributor in a different country. The shipment must include an
original purchase receipt or proof of purchase with the purchase date. Excluded are any
consequential damages, cosmetic damages, damages to products which show abuse,
non-conformance with the instructions, particularly water damage due to damaged
O-ring or removed O-ring or any particles wedged between the housing and the O-ring, or
tampering and attempted repair of the product. Excluded are scratches on lenses or
damaged lens coatings. Cameras used in rental operations are excluded from this
warranty and have a special service support program (Contact SeaLife/Pioneer Research).
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in commercial installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, detectable by turning the equipment in question off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna; Increase the distance between the equipment
and the receiver; Connect the equipment to an outlet on a different circuit than that
which the receiver is connected to; Or consult the dealer or an experienced radio/TV
technician for help.
E
NOTE
A shielded-type DC power cable incorporated with a ferrite core is required in order to
meet the FCC emission limits and also to prevent interference to nearby radio and
television reception. Use only shielded I/O cable incorporated with a ferrite core to
connect this equipment to host computer or TV set. Shielded AC power cable and
shielded I/O cables are required in order to meet the FCC emission limits. It is essential
that only the supplied power cord and I/O cable(s) be used.
Service: Do not contact your dealer for product questions or service.
After going through the Trouble Shooting Guide in this manual, if you cannot find a
solution for a problem: Contact the SeaLife Service Center or send the camera with the
housing to an authorized SeaLife service facility or directly to SeaLife Headquarters in
Moorestown, NJ USA or the SeaLife distributor in your country. (A list of SeaLife
distributors can be found on the website www.sealife-cameras.com). Include: US$10.00
for handling and domestic shipping; your day time phone number, proof of purchase and
return address (No P.O. BOX); a clear written description of problem.
Ship prepaid to:
Pioneer Research, Attn: SeaLife Service Center, 97 Foster Road, Suite 5
Moorestown, NJ 08057 USA
iiii
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
This camera is not waterproof or water resistant. Use the inner camera
only inside the SeaLife waterproof housing when in or around water.
Follow waterproof housing instructions carefully to prevent water
damage to camera. Water damage to camera is not covered by warranty
unless it has been determined that the waterproof housing leaked water as
a result of a manufacturing defect.
Do not use this camera if it is emitting smoke, emitting any unusual odor
or noise, or if it is in any other abnormal state. Operating the camera in any
of these situations may cause a fire or an electrical shock. Stop using the
camera immediately, turn the camera off, and then disconnect the power
source (batteries or AC power adapter). (If you are using the AC power
adapter, unplug the adapter from the AC power outlet after you have
disconnected the camera.) After checking that smoke is no longer being
emitted, contact your local authorized SeaLife service facility and request
repairs. Never attempt to repair this camera yourself as this is dangerous.
E
Do not use the camera if any water has entered the camera, even after
camera has dried. Turn the camera off, and then disconnect the power
source (batteries or AC power adapter). (If you are using the AC power
adapter, unplug the adapter from the AC power outlet after you have
disconnected the camera.) Then contact your local SeaLife authorized
service facility. Do not continue to use the camera as this may cause a fire
or an electrical shock. Be careful when handling wet camera. Camera and
batteries may become very hot.
Do not use the camera if any foreign objects have entered the camera.
Turn the camera off, and then disconnect the power source (batteries or
AC power adapter). (If you are using the AC power adapter, unplug the
adapter from the AC power outlet after you have disconnected the cam-
era.) Then contact your local SeaLife authorized service facility. Do not
continue to use the camera as this may cause a fire or an electrical shock.
If the camera has been dropped or if the camera case has been damaged,
turn the camera off, and then disconnect the power source (batteries or
AC power adapter). (If you are using the AC power adapter, unplug the
adapter from the AC power outlet after you have disconnected the cam-
era.) Then contact your local SeaLife authorized service facility. Do not
continue to use the camera as this may cause a fire or an electrical shock
Do not expose the camera to moisture and make sure that there is no
water getting into the camera. Take particular care when using the
camera under extreme weather conditions such as rain or snow, or when
operating the camera at the beach on near water. Water in the camera
may cause a fire or an electrical shock.
iiv
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Do not insert or drop metallic or flammable foreign objects into the
camera through access points such as the Compact Flash card slot. This
may cause a fire or an electrical shock.
Do not attempt to modify this camera. This may cause a fire or an
electrical shock.
Do not remove the camera casing. This may cause an electrical shock.
Internal inspection, maintenance and repairs should only be carried out by
your local authorized SeaLife service facility.
Do not touch camera, charger or AC adapter during a thunderstorm if you
are using the AC power adapter. This may cause an electrical shock.
E
Never operate this camera in any way while driving a vehicle. This may
cause a traffic accident.
Do not place the camera in any unstable locations such as on a wobbly
table or sloping surface where the camera may fall or tip over and cause
injury.
Do not place camera, charger or batteries in damp or dusty locations.
This may cause a fire or an electrical shock.
Do not place this camera in a location affected by oil fumes, steam,
seaspray, rain, boat deck, damp clothes, cooking stove or humidifier. This
may cause a fire or an electrical shock.
Do not leave this camera in a location subject to extremely high tempera-
tures, such as in a sealed vehicle or in direct sunlight. Exposure to high
temperatures may adversely affect the camera case and internal
components and may cause a fire.
Do not cover or wrap the camera, battery charger or the AC power
adapter with a cloth or quilt. This may cause heat to build up and distort
the case and cause a fire. Always use the camera and its accessories in
well-ventilated locations
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Handle the camera carefully and do not bump the camera into any hard
object. Handling the camera roughly may cause a malfunction.
Do not move the camera while it is attached to AC adapter, USB or video
cable. (If you are using the AC power adapter, unplug the adapter from the
AC power outlet after you have switched off the camera.)
Ensure that any connector cords or cables to other devices are
disconnected before moving the camera. Failure to do so may damage the
cords or cables and cause a fire or an electrical shock.
When handing the camera ,always unplug it from the power source (AC
power adapter) for safety. (If you are using the AC power adapter, unplug
the adapter from the AC power outlet after you have disconnected the
camera.) Failure to do may result in an electrical shock.
E
When leaving the camera unused for long periods, such as during a
vacation, always remove the batteries or unplug the camera from the AC
power adapter for safety. (If you are using the AC power adapter, unplug
the adapter from the AC power outlet after you have disconnected the
camera.) Failure to do so could result in a fire.
Do not use batteries other than those specified for use with your camera.
The use of unsuitable batteries may result in the batteries splitting or
leaking and causing a fire, injury, or damaging the battery compartment.
When inserting batteries into the camera, check the polarity markings on the
battery ( - and + ) to ensure that you insert the battery correctly. Incorrect
battery polarity may result in the batteries splitting or leaking and causing a
fire, injury, or damaging of the battery compartment.
Remove the batteries if the camera will not be used for an extended period
of time. The batteries may leak and cause a fire, injury or damage the
battery compartment. If the batteries leak, clean and wipe the battery
compartment carefully and install new batteries. Wash your hands
carefully if you touch the battery fluid.
Do not leave battery charger plugged into AC outlet after charging is
complete. Remove batteries from charger when charging is complete.
ivi
Download from Www.Somanuals.com. All Manuals Search And Download.
TRADEMARK INFORMATION
I Microsoft® and Windows® are U.S. registered trademarks of Microsoft
Corporation.
I Pentium® is a registered trademark of Intel Corporation.
I Macintosh is a trademark of Apple Computer, Inc.
I SDTM is a trademark.
I PhotoSuite, PhotoVista and the MGI logo are trademarks or registered
trademarks of MGI Software Corp.
I Adobe, the Adobe logo, and Acrobat are trademarks of Adobe Systems
Incorporated.
I SeaLife®, Reefmaster®, Land & Sea® are registered trademarks of
Pioneer Research..
I Other names and products may be trademarks or registered trademarks of
their respective owners.
E
NOTICE
Please start by reading the important messages below first.
1. The bundled driver, software, design, specifications and user’s manual that
packaged with the camera are subject to change without notice.
2. The accessories that come with the camera may vary between regions.
3. Driver updates are [posted on the SeaLife website;
4. We are not liable whatsoever for any compensation arising from errors in
descriptions in this user’s manual.
ivii
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
I Do not place the camera in damp or dusty locations. This may cause a fire or
an electrical shock.
I Do not place the camera in a location affected by oil fumes or steam, such as
near a cooking stove or humidifier. This may cause a fire or an electrical shock.
I Exposure to high temperatures may adversely affect the camera case and
internal components and may cause a fire.
I Do not cover or wrap the camera or the AC power adapter with a cloth or quilt.
This may cause heat to build up and distort the case and cause a fire. Always
use the camera and its accessories in well-ventilated locations
I Handle the camera carefully and do not bump the camera into any hard object.
Handling the camera roughly may cause a malfunction.
I Do not move the camera while it is switched on. (If you are using the AC power
adapter, unplug the adapter from the AC power outlet after you have switched
off the camera.) Ensure that any connector cords or cables to other devices
are disconnected before moving the camera. Failure to do so may damage the
cords or cables and cause a fire or an electrical shock.
E
I When leaving the camera unused for long periods, such as during a vacation,
always unplug the camera from the power source (batteries or AC power
adapter) for safety. (if you are using the AC power adapter, unplug the adapter
from the AC power outlet after you have disconnected the camera.) Failure to
do so could result in a fire.
I Do not use batteries other than those specified for use with the camera. The
use of unsuitable batteries may result in the batteries splitting or leaking and
causing a fire, injury, or soiling of the battery compartment.
I When fitting batteries into the camera, check the polarity markings on the
battery (- and +) to ensure that you insert the battery correctly. Incorrect
battery polarity may result in the batteries splitting or leaking and causing a
fire, injury, or soiling of the battery compartment.
I Remove the batteries if the camera will not be used for an extended period of
time. The batteries may leak and cause a fire, injury or soiling of the battery
compartment. If the batteries leak, clean and wipe the battery compartment
carefully and install new batteries. Wash your hands carefully if you touch the
battery fluid.
iviii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
PLAYBACK MODE . . . . . . . . . . . 32
Viewing images . . . . . . . . . . . . . . 32
Zoom Playback . . . . . . . . . . . . . . 33
Displaying thumbnail images . . . . 34
Slideshow display . . . . . . . . . . . . 34
Deleting images. . . . . . . . . . . . . . 35
INTRODUCTION. . . . . . . . . . . . . 13
How It Works. . . . . . . . . . . . . . . . 13
Package contents . . . . . . . . . . . . 15
Common (Optional)
Accessories . . . . . . . . . . . . . . . . . 15
GETTING TO KNOW
MOVIE MODE. . . . . . . . . . . . . . . 36
Recording video clips . . . . . . . . . 36
Viewing video clips . . . . . . . . . . . 37
THE CAMERA. . . . . . . . . . . . . . . 16
Front view . . . . . . . . . . . . . . . . . . 16
Rear view. . . . . . . . . . . . . . . . . . . 17
Mode dial. . . . . . . . . . . . . . . . . . . 18
LED indicators . . . . . . . . . . . . . . . 18
Status LCD . . . . . . . . . . . . . . . . . 19
LCD monitor information . . . . . . 20
E
TRANSFERRING RECORDED
IMAGES TO YOUR
COMPUTER . . . . . . . . . . . . . . . . 38
Step 1: Installing the USB driver
on Windows
computers. . . . . . . . . . . . . . . . . 39
Installing the USB driver
on Macintosh
computers. . . . . . . . . . . . . . . . . 39
Step 2: Connecting the camera
to your computer. . . . . . . . . . . . 39
Step 3: Downloading images/video
clips. . . . . . . . . . . . . . . . . . . . . . 40
For computers running Windows
. . . . . . . . . . . . . . . . . . . . . . . . . 40
For computers running Mac OS
. . . . . . . . . . . . . . . . . . . . . . . . . 40
GETTING STARTED . . . . . . . . . . 21
Installing the batteries . . . . . . . . . 21
Using the AC power adapter . . . 21
Loading a SD memory card. . . . . 22
Attaching the strap . . . . . . . . . . . 22
Choosing the language . . . . . . . . 23
Setting the date and time . . . . . . 23
Setting the image resolution
and quality. . . . . . . . . . . . . . . . . . 24
RECORD MODE. . . . . . . . . . . . . 25
Taking pictures. . . . . . . . . . . . . . . 25
Using the viewfinder . . . . . . . . . 25
Using the LCD monitor . . . . . . . 26
Using the normal mode . . . . . . . . 26
Using the macro mode . . . . . . . . 27
Using the digital zoom. . . . . . . . . 28
Using the self-timer . . . . . . . . . . . 29
Using the flash. . . . . . . . . . . . . . . 30
Taking pictures manually . . . . . . . 31
INSTALLING
MGI PHOTOSUITE . . . . . . . . . . 41
INSTALLING
MGI PHOTOVISTA . . . . . . . . . . . 42
iix
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING
USING THE USER’S
Underwater Housing Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . 56
MUST DO for Housing . . . . . . . . 57
Main O-Ring . . . . . . . . . . . . . . . . 59
SeasLife ReefMaster Underwater.
Housing . . . . . . . . . . . . . . . . . . . . 60
Rear View . . . . . . . . . . . . . . . . . 61
Set-Up. . . . . . . . . . . . . . . . . . . . 62
Cleaning . . . . . . . . . . . . . . . . . . 64
Great Pictures Made Easy. . . . . 65
Battery Selection Guide. . . . . . . . 67
Trouble Shooting Guide . . . . . . . . 69
MANUAL. . . . . . . . . . . . . . . . . . . 43
ACROBAT READER . . . . . . . . . 44
MENU OPTIONS . . . . . . . . . . . . 45
Record menu. . . . . . . . . . . . . . . . 45
LCD BRIGHTNESS . . . . . . . . . . 45
QUICK VIEW . . . . . . . . . . . . . . . 45
DIGITAL ZOOM . . . . . . . . . . . . . 45
WHITE BALANCE . . . . . . . . . . . 46
EV COMPENSATION. . . . . . . . . 46
SHARPNESS. . . . . . . . . . . . . . . 47
Flash On/Off . . . . . . . . . . . . . . . 47
EXIT. . . . . . . . . . . . . . . . . . . . . . 47
Playback menu . . . . . . . . . . . . . . 48
LCD BRIGHTNESS . . . . . . . . . . 48
SLIDE SHOW . . . . . . . . . . . . . . 48
COPY TO CARD . . . . . . . . . . . . 48
DELETE ALL . . . . . . . . . . . . . . . 48
DPOF . . . . . . . . . . . . . . . . . . . . 49
EXIT . . . . . . . . . . . . . . . . . . . . . 49
Movie menu. . . . . . . . . . . . . . . . . 50
LCD BRIGHTNESS . . . . . . . . . . 50
EXIT. . . . . . . . . . . . . . . . . . . . . . 50
Setup menu. . . . . . . . . . . . . . . . . 51
DATE/TIME . . . . . . . . . . . . . . . . 51
LANGUAGE. . . . . . . . . . . . . . . . 52
SOUND . . . . . . . . . . . . . . . . . . . 52
FORMAT MEDIA . . . . . . . . . . . . 52
VIDEO MODE . . . . . . . . . . . . . . 52
AUTO POWER OFF . . . . . . . . . 53
RESET TO DEFAULT. . . . . . . . . 53
E
CONNECTING THE CAMERA TO
OTHER DEVICES . . . . . . . . . . . . 54
CAMERA SPECIFICATIONS . . . 55
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
How It Works - A Very Unique Camera
®
Land & Sea
The SeaLife Reefmaster Digital Land & Sea camera allows you to choose
between Land Mode for taking land pictures and Sea Mode for taking
underwater pictures. This is essential for taking great pictures and achieving the
perfect picture exposure.
Sea Mode: If the camera is set to Sea Mode and used inside the Underwater
Camera Housing, the camera is programmed to automatically find the best
exposure control combination in an underwater environment. The internal
sensor reads the light conditions through the lens (TTL). It evaluates the whole
picture in 64 segments with higher priority in the center. Then it automatically
sets the correct exposure time, lens opening, and sensitivity. You may hear a
slight clicking noise when you move the camera to different light conditions.
SeaLife Research has tested several thousand combinations to achieve the
optimal exposure controls. In the Sea mode, the slowest exposure time
underwater is 1/30 seconds. If the surrounding light is too dark, the flash will fire
automatically. While in the Sea mode, the camera flash will actually fire two,
three or four times depending on the distance to the subject. The weaker
flashes, called a pre-flash, is used to determine the brightness and reflection of
whatever you’re taking a picture of. The primary flash will fire 0.2 seconds after
the pre-flash (hardly noticeable). Only the primary flash is used by the camera
for properly exposing the final picture. The combination of the pre-flashes and
main flash ensures the optimal exposure setting for the camera.
E
In order to avoid underwater “backscatter” (spots that show up in pictures
caused by tiny particles in the water) and get more vivid colors, we
recommend that you use the SeaLife External Flash, which is sold
separately. You can even use two external flashes, like the pros do, in order to
eliminate shadows in your pictures. When using the SeaLife External Flash, you
must set the camera to the External Flash Mode. The External Flash Mode does
not use a pre-flash, since this would cause the external flash to fire during the
pre-flash and not during the primary flash.
If you are taking close-up pictures in very low light or even total darkness with
the SeaLife Macro lenses and you experience overflashing from a reflective fish
or object, you have the choice of immediately deleting the image by pressing the
shutter button again within 3 seconds (the monitor will show you the picture and
display “DELETE THIS?”). You can then redirect the flash by moving the flexible
flash arm or attaching the flash diffuser. The Flash Diffuser is an accessory that
can be clipped on to the external flash head. The system gives you many
options to create great photos under many different conditions and using the
various flashes or lens accessories.
continued on following page
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Mode: If you are taking land pictures, set the camera to Land Mode.
Now the camera is automatically programmed to take great land pictures. The
camera evaluates light conditions through the lens. If it’s too dark, the camera
uses the built-in flash to fire a pre-flash (to test the picture quality) and a primary
flash for taking a properly exposed picture. If you like, you can override the
camera’s fully automatic functions. In many cases you might actually take a
better picture without flash, such as in longer shooting distances in low light or
indoor, and you can select “no flash.” In other cases, even in bright light, you
might select “fill-flash” to brighten up shadows and avoid dark areas.
Sometimes pictures can be “grainy” if you do not have enough light and do not
use the flash. No matter how dark it is, even if it becomes impossible for any
camera to take a sharp picture, the camera will still try to take a picture. If that
happens, get closer to the subject and use a flash or another good light source.
In general, the closer you are to your subject and the brighter the light
conditions are, the better the picture results will be. With a little experimenting
you will quickly be on your way towards great digital pictures to share with your
friends and family.
E
Your computer
It’s easy to connect the camera to your computer, to download pictures, edit
pictures and print or email pictures.
Download – The USB connection will quickly transfer pictures from your
camera to your computer. Please refer to the detailed instructions on page 29
on how to connect your camera to the computer.
Editing – You will enjoy picture editing with MGI Photo Suite®, but you can
also use your own picture-publishing program that you are familiar with. First
take pictures in the highest quality setting. Then you can make adjustments to
the image on your computer, like cropping, adjusting the picture size or some
really creative special effects.
Printing – For photo-like 5” x 7” prints, set the printer on the highest resolu-
tion and use high-quality glossy photo paper. You will discover that creating a
vacation trip report on Word® with your best pictures is an impressive way to
save and share your memories.
There are many great books and websites dedicated to the world of digital
the best website and other suggestions on how to learn more about digital
photography.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Package contents
Carefully unpack your package and make sure that you have the following items.
Common Product Components:
I Digital camera I Software CD-ROM
I Video cable
I Quick Guide
I USB cable
I Camera strap
I Camera Carry Case
I Underwater Housing
I Deflector for External Flash
E
Common (Optional) Accessories:
I SD memory card
I 4 – Pack Rechargeable batteries
(up to 128MB capacity)
I AC power adapter
I 4 rechargeable NI-MH
with charger and foreign plug
adapters (SL 190)
I Carry Case and more acces-
are available.
sories I External Flash
I Wide angle lens
I Macro lenses
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW THE CAMERA
Front view
E
1. Status LCD
8. Flash
2. Shutter button
3. Viewfinder window
4. Lens cover
5. Focus switch
6. Flash button
9. Lens
10. Strap eyelet
11. DC IN jack
12. USB connector
13. Self-timer light
7. Quality/Resolution button
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view
Menu Navigation button:
1.
2.
Menu navigation button (up)
Menu navigation button (left)
Self-timer button
3. OK OK button
Digital zoom button
Menu navigation button
4.
5.
Menu navigation button (right)
Menu navigation button (down)
Delete button
E
Camera buttons:
1. LED “camera ready” indicator
2. Viewfinder (option)
5.
6.
Menu button
Power button
7. Mode dial
3. LCD monitor
8. Battery/SD card cover
9. VIDEO OUT jack
10.Tripod socket
4. LCD On/Off, Quick Review button
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode dial
1. Record mode
2. Playback mode (Review)
3. Setup mode
4. Movie mode
Mode
Record Mode
Playback mode
(Review)
Description
Use this mode to capture still images.
Use this mode to view images & videos,
delete images & video clips, view a slide
show, view thumbnail displays.
E
Setup mode
Movie mode
Use this mode to adjust camera settings and
Land & Sea exposure modes.
Use this mode to record video (movie) clips.
LED indicators
Indicator
Status
Description/Activity
Camera system error
Charging the flash
Sound
Yes *(3)
No
LED Indicator
LED Indicator
LED Indicator
Blinking red
Solid orange
Blinking green
Image is being recorded to
the memory card.
No
LED Indicator
Self-timer
Solid green
Blinking red
The camera is ready to record
images (or movies).
The self-timer function
is activated.
Yes *(1)
Yes *(1)
Indicator
None
None
None
Error message
Yes *(3)
Yes *(1)
None
Valid button event
*(3) The camera sounds three beeps.
*(1) The camera sounds one beep.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Status LCD
Flash mode
Image quality
E
Auto flash
Fine
Red-eye reduction
Fill flash (on)
Flash off
Normal
Basic
Macro mode
Slow synchro
Battery check
Image resolution
Full battery power
1600 x 1200 pixels
800 x 600 pixels
Medium battery power
Low battery power (replace batteries)
Virtually No battery power
Self-timer mode
Card indicator
This display varies according to the camera mode setting:
Displays the estimated shots that you can take in Record mode
.
Displays the estimated seconds that you can record for the video clip in Movie
mode
Displays the current number of the recorded image in Playback mode
.
.
Displays “PC” when connecting the camera to your computer by using the USB
cable.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD monitor information
The displayed indicators when recording still images:
Sea Mode indicator
Ext Flash indicator
The displayed indicators when recording video clips:
E
The displayed indicators when playing images back:
The displayed indicators when playing video clips back:
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
You can use either 2 AA size batteries (High-Energy Alkaline, Ni-MH) or an AC
power adapter (optional accessory) to power the camera. Battery power is
convenient for recording images or video clips while AC adapter power is
recommended for transferring images to your computer.
Installing the batteries
1. Make sure the camera is off.
2. Slide the battery/SD card cover in the direc-
tion of the OPEN arrow.
3. Insert the batteries according to the correct
polarity marks (+ or -).
4. Close the battery/SD card cover firmly.
E
• We recommend Sealife Ni-MH batteries for long lasting operation.
• If you won’t be using the batteries for an extended period of time, remove
them from the camera to prevent leaks or corrosion.
• Never use manganese batteries.
• Never use different types of batteries (together) or mix old and new batteries.
Using the AC power adapter
(optional accessory)
1. Make sure the camera is off.
2. Open the DC IN jack cover and connect one
end of the AC power adapter to the DC IN
jack on the camera.
3. Connect the other end to an electrical outlet.
• Make sure to use only the specified AC power adapter (3.3 DC volt) for the
camera. Otherwise, it may cause damages to the camera, which is not
covered under the warranty. SeaLife item #SL13132.
• To prevent unexpected auto power off resulting from no battery power left
during the process of transferring your images to the computer, use the AC
power adapter as a power supply.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading a SD memory card
(optional accessory)
The camera comes with 8MB of internal
memory, allowing you to store images and video
clips in the camera. However, you can expand
the memory capacity by using an optional SD
memory card so that you can store additional
images and video clips.
1. Make sure the camera is off.
2. Slide the battery/SD card cover in the direction of the OPEN arrow.
3. Insert the SD memory card.
I The front side of the memory card (printed arrow) should face towards the
front side of the camera.
I If the card cannot be inserted, check the orientation.
4. Close the battery/SD card cover.
E
I To remove the SD memory card, make sure the camera is off. Open the
battery/SD card cover. Press lightly on the edge of the memory card and it
will eject.
• To prevent valuable data from being accidentally
erased from an SD card you can slide the write
protect tab (on the side of the SD memory card) to
“LOCK.”
Write protection
locked
Write protection
unlocked
• To save, edit, or erase data on an SD memory card,
you must unlock the card.
Attaching the strap
To prevent accidental dropping of the camera,
always use the strap.
1. First thread the small loop of the wrist strap
through the strap eyelet on the camera and
then pull the large loop through the small loop
until the strap is firmly secured.
• Remove wrist strap from camera before inserting into underwater housing.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Choosing the language
When you first turn the camera on, the language
setting screen appears, prompting you to choose
a language for displayed information on the LCD
monitor. Follow the steps below to set the OSD
(On-Screen Display) language.
1. Select a language that you prefer by using the
/
button.
2. Press the OK button to confirm.
• The language setting will be retained even if
the camera is turned off.
E
• The language setting screen is located in the
set-up menu. Turn mode dial to “set-up.”
Setting the date and time
The Date/Time screen will be presented if/when:
I Camera is turned on for the first time (after setting the language)
I Camera is turned on after removing or replacing the batteries.
When the date and time setting screen appears, follow these steps to set the
correct date and time. You may skip this procedure by pressing the OK button
repeatedly.
1. Enter the values of the year, month, day and time fields by using the
button. Press the OK button after each field is set.
/
/
/
I To increase a value, press the
I To decrease a value, press the
/
button.
button.
/
• The date/time screen is located in the set-up menu.
• Turn mode dial to “set-up.”
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the image resolution and quality
Resolution and quality settings determine the pixel size (dimension), image file
size, and compression ratio for your images. These settings affect the number
of images that can be stored in memory, or on an SD memory card. As you get
to know the camera, it is recommended that you try each quality and resolution
setting to better understand the effects that these settings will have on your
images.
Higher resolution and higher quality images offer the best photographic results
but produce large files sizes. Therefore, fewer images will take up more
memory space.
High resolution and quality settings are recommended for printed output and
situations requiring the finest detail. Lower resolution/quality images take up less
memory space and may be quite suitable for sharing images via e-mail, in a
report, or on a web page. To change image resolution and quality settings, press
E
the
button on top of the camera repeatedly to select the settings that you
prefer. As you press this button watch the Status LCD.
Resolution & Quality:
The camera provides 2 resolution modes and 3 quality modes, which can be
changed cyclically by pressing the
button. The cyclical order is
➔ repeat.
➔
➔
➔
➔
➔
Resolution & quality indicators on the status LCD
In the
mode: shows the resolution & quality settings of the image to be
recorded
In the
mode: shows the resolution & quality settings of the recorded image.
The table below shows the approximate shots that you can take at each setting
based on 8MB internal memory or a 8MB SD memory card.
Resolution
Quality
Compression 8 MB internal 128 MB SD
ratio
memory
memory card
1600x1200
pixels
Fine
Normal
Basic
8:1
12:1
20:1
10
15
20
175
260
350
800x600
pixels
Fine
Normal
Basic
4:1
8:1
16:1
40
60
80
700
1050
1400
* The above data shows the standard testing results. The actual capacity varies accord-
ing to the shooting conditions and settings.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORD MODE
Taking pictures
Your camera is equipped with both an optical viewfinder and a 1.6" LCD
monitor to compose images. Taking images using the optical viewfinder will con-
serve battery power. If your batteries are low, it is recommended that you only
compose images by using the viewfinder. Using the LCD monitor you can
compose images more accurately, but at the cost of battery consumption.
Always use the image LCD for macro shots, to avoid parallax error. The LCD
image display must be turned on when Digital Zoom is used.
Using the viewfinder
1. Open the lens cover.
2. Turn the mode dial to the
E
mode.
3. Turn the camera on by pressing the
4. Compose your shot in the viewfinder.
5. Check “camera-ready” light is green.
button.
6. Press and hold the shutter button until camera
takes picture.
• Replace batteries if camera-ready light takes more than 15 seconds to
recycle (after taking a picture).
• The camera-ready light blinks green while camera is processing a
captured image
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the LCD monitor
1. Open the lens cover.
2. Turn the mode dial to the
mode.
3. Turn the camera on by pressing the
button.
4. Turn the LCD monitor on and off by pressing the
button.
5. Compose the picture.
6. Press the shutter button.
I The LED indicator blinks green while the camera is processing a captured
image.
E
• The image on the LCD monitor darkens when in strong sunlight or bright light.
This is not a malfunction.
• Using the LCD monitor for an extended period of time will decrease the
battery life and the number of images you can take. To increase battery life,
turn the LCD monitor off and use the optical viewfinder instead.
• Always use the image LCD for macro shots.
• The LCD monitor must be on when Digital Zoom is to be used.
Set Focus to Normal Distance
The normal focus setting is used to take images
where the distance to the subject is 3 ft. (75 cm)
or more. Select this setting for general shooting,
including portraits and scenery.
1. Open the lens cover, turn the mode dial to
the
mode, and power on the camera.
2. Move the focus switch located on the front
Camera’s focus is set to normal
distance.
side of the camera to the
3. Compose the picture.
4. Press the shutter button.
position.
• The shooting distance for underwater pictures are different than land pictures.
Underwater pictures are in focus from 2 ft. (50cm) to infinity.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the macro focus setting
Use the macro focus setting to shoot a close-up of the subject, such as flowers
or insects.
The effective range is between 1 to 3ft (25 to 75 cm).
1. Open the lens cover, turn the mode dial to the
mode, and power on the camera.
2. Move the focus switch located on the front side
of the camera to the
I The icon appears on the LCD monitor and
status LCD.
position.
Camera’s focus is now set to
macro distance.
3. Compose the picture.
E
4. Press the shutter button.
I To disable macro photography, slide the focus switch back to normal.
• When shooting a close-up in macro mode, use the image LCD monitor to compose your shot.
• Using optical viewfinder may result in parallax error.
• For land pictures taken at 3ft. shooting distance take pictures in normal and macro focus setting
and compare the results.
• After a macro shot is taken DO NOT FORGET to reset the lens to the normal position.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the digital zoom
Using digital zoom, images appear closer.
Whereas digital zoom is a compelling feature,
the more an image is enlarged (zoomed), the
more pixilated (grainier) the image will appear.
The digital zoom function is only available when
you set the LCD monitor and the digital zoom to
ON. To enable the digital zoom, refer to DIGITAL
ZOOM in Record menu.
2X
1. Open the lens cover, turn the mode dial to the
mode, and power
on the camera.
2. Turn the LCD monitor on by pressing the
3. Press the OK button to activate 2X digital zoom function.
I The 2X icon appears on the LCD monitor.
button.
E
I To cancel the digital zoom function, press the OK button.
4. Press the shutter button to capture a "zoomed" image.
• You can only set the digital zoom at the resolution of 1600x1200 pixels;
digital zoom is not available at the resolution of 800x600 pixels. When you play
back a “digitally zoomed” image, the image size is 800x600 pixels.
• The more the image is enlarged, the more pixilated (grainier) the image.
• Digital zoom cannot be used in the movie mode.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the self-timer
The self-timer duration is 10 seconds. After the activation of the self-timer by
pressing the shutter button, the self-timer lamp starts blinking slowly for 7 sec-
onds and then blinking faster for the rest of 3 seconds. This allows you to get
into the scene when taking group images.
1. Secure the camera to a tripod or place it on a
stable surface.
2. Open the lens cover, turn mode dial to the
mode, and power on the camera.
3. Press the
button.
I The
icon appears on the LCD monitor and
status LCD.
4. Compose the picture.
E
5. Press the shutter button.
I The self-timer function is activated.
6. After ten seconds, the camera takes an image.
I To cancel self-timer photography at any time, press the shutter button to
disrupt the sequence.
• After one shot is taken, the self-timer mode is turned to off.
Using the flash
The flash is designed to function automatically
when lighting conditions warrant the use of flash.
You can take an image using a flash mode suitable
to your circumstances. If you change the flash
mode, the camera will retain that setting even if the
camera is turned off.
1. Open the lens cover, turn the mode dial to the
the camera.
mode, and power on
2. Press the button located on top of the camera repeatedly until your desired
flash mode appears.
3. Compose the picture and press the shutter button.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash Modes
The camera has five flash modes: Automatic Flash (default), Red-Eye Reduction,
Fill flash (on), Flash Off and Slow Synchro. The modes appear, cyclically, when
you press the flash button on top of the camera. The table below will help
choose the appropriate flash mode:
Flash Mode
Description
[
] Auto Flash
The flash fires automatically according to the ambient
conditions. Select this mode for general photography.
[
] Red-eye
Reduction
The flash emits a precursor-flash before the main flash
fires. This causes the pupil in the human eye to
constrict, reducing the red-eye. Select this mode when
taking pictures of people and animals in low-light
conditions.
E
[
[
[
] Fill Flash (on)
] Flash Off
The flash will always fire regardless of the surrounding
brightness. Select this mode for recording images with
high contrast (backlighting) and deep shadows.
Also known as forced flash.
The flash will not fire. Select this mode when taking
images in a place where flash photography is prohibit-
ed, or when the distance to the subject is beyond the
effective range of the flash.
] Slow Synch
The flash fires and the shutter speed is reduced so that
the subject will be exposed correctly while taking a
image with dark (night) background.
• You can also change the flash mode setting in the record menu screen.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking pictures manually
You can manually adjust conditions such as white balance, EV compensation
and sharpness when taking pictures. For white balance, EV compensation and
sharpness information, refer to WHITE BALANCE, EV COMPENSATION or
SHARPNESS in Record menu.
To take pictures manually:
1. Turn the camera on.
2. Turn the mode dial to the
3. Press the button.
4. Move to WHITE BALANCE,
EV COMPENSATION or SHARPNESS with the
button.
mode.
E
/
Press menu button to manually
adjust exposure settings.
5. Change the settings by using the
and then press the OK button.
6. Compose the picture.
/
button
7. Press the shutter button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE (Review images)
In the
mode, you can view, magnify, delete images, play video clips, or run a
slide show. Playback mode also provides a thumbnail image display, allowing
you to quickly search for the image you want.
Viewing images
You may view your images without opening the lens cover since the lens is not
used for playback. The camera lens is protected during playback.
1. Turn the mode dial to the
the camera.
mode and power on
2. Select the image that you want to view by using
the button.
E
/
I To view the previous image, press
the button.
I To view the next image, press the button.
• If there is no image stored in the internal memory or on the memory card, “
NO IMAGES” message will appear on the LCD monitor.
• You can also view your images on the TV screen. Connect one end of the video cable
to the video out jack of the camera and connect the other end to the video input of your
TV. Turn the mode dial to the
mode and then turn on both TV and camera.
• When lens cover is closed and the mode dial is set to record image
also be able to playback images.
mode, you will
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom Playback
While reviewing your images, you may enlarge a selected portion of an image.
This magnification allows you to view fine details.
1. Turn the mode dial to the
camera power on.
mode with the
2. Select the image that you want to view by using
the button.
/
3. Enlarge the image by pressing the OK button.
I Pressing the OK button once magnifies the
image to 2X. Pressing it again magnifies
the image to 4X. When enlarging the
Current position of enlargement
Entire image
E
recorded image, you will see a red frame
with a red box inside. The red frame
indicates the entire image, while the red box
shows the enlarged area.
4. To view the different portion of the enlarged
image, press the
5. To return to the regular display from 4X-
/
/
/
button.
4X
enlarged status, press the OK button twice.
• Pressing the OK button magnifies the image from 1X ➔ 2X ➔ 4X.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying thumbnail images
This function allows you to view nine thumbnail
images on the LCD monitor simultaneously so you
may search for a particular image.
1. Turn the mode dial to the
the camera.
mode and power on
2. Press the
button once.
I The image information appears on the LCD
monitor.
3. Press the
button again.
I Nine thumbnail images appear on the LCD monitor (assuming there are nine
or more images in memory).
I To view a full-size image, press the OK button after selecting it by using the
E
/
button.
• By pressing the
button repeatedly, the image will show as follows.
Image only ➔ Image and OSD (on-screen display) ➔ Thumbnail image display
Slideshow display
The slideshow function enables you to playback
your images back automatically in sequential order
as a slide show. This is a very useful and entertain-
ing feature for reviewing recorded images and for
presentations.
1. Turn the mode dial to the
the camera.
mode and power on
2. Press the
button and move to SLIDE SHOW by using the
/
button.
3. Set the playback interval by using the
button.
/
button and then press the OK
I The slideshow starts, displaying your images on the LCD monitor, one by
one, at the set interval.
I To stop the slideshow display, press the OK /
/
/
button.
• You can adjust the slideshow display interval within the range of 2 sec. to 10 sec. For
interval setting, refer to SLIDE SHOW in the Playback menu.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting images from memory
You can delete one image/video clip by pressing the button.
To delete one image at a time:
1. Turn the mode dial to
.
2. Select the image/video clip you want to delete
by using the
button. (
/
button. And then press the
button.)
3. Select [YES], and then press the OK button. The
next image/video clip appears.
I If you want to cancel the deletion, select [NO].
4. Continue the deletion if necessary. If all images are deleted, [ NO IMAGES]
pops up. To exit this function, turn the mode dial to any other mode.
E
• To delete the images or video clips stored in the internal memory, remember
not to insert the memory card in the camera. Otherwise, you will delete the
images or video clips stored in the memory card.
How to use the instant delete feature:
You can instantly delete a picture immediately after taking the picture
To instantly delete a picture:
1. After taking a picture, the LCD will display a “DELETE THIS?” message with
the last picture taken.
2. If you want to delete the image displayed, press the shutter button while the
“DELETE THIS?” message is displayed.
3. The LCD will display a “DELETE IMAGE” message and the image is now
deleted.
4. If you do not want to delete the image, do not press the shutter button when
“DELETE THIS?” is displayed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MOVIE MODE
Recording video clips
The movie mode allows you to record video clips at
the resolution of 320 x 240 pixels.
1. Open the lens cover, turn the mode dial to the
mode, and power on the camera.
I The recordable movie time displays on the
status LCD and the LCD monitor.
2. You can start recording a video clip by pressing the shutter button.
I The elapsed time displays on the LCD monitor while recording a
video clip.
I To stop recording, press the shutter button again.
E
• In movie mode, resolution/quality, macro, self-timer cannot be set or
activated.
• In movie mode, the flash mode is automatically set to [OFF].
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing video clips
To view the recorded video clips, follow the steps below.
1. Turn the mode dial to the
mode and power on the camera.
2. Select the video clip that you want to view by using the
3. Press the shutter button to start.
/
button.
I To pause playback at any time, press the shutter button again.
I To stop playback, press the
button.
Pressing the shutter button or the
change the status as follows:
button while playing back the video clip will
E
•
•
The zoom function cannot be activated while playing the video clip back.
To play the video clip back on the computer, we recommend that you use the “Quick
Time Player.” This software is free of charge, compatible for Mac and Windows-based
Time Player usage, please refer to its on-line help for more information.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING RECORDED IMAGES
TO YOUR COMPUTER
You can share recorded images/video clips with your family or friends via e-mail
or post them on the Web. First, you need to connect the camera to your com-
puter by using the USB cable and then transfer the images/video clips.
To transfer images/video clips from the camera to your computer, follow the
steps below.
Step 1: Installing the USB driver (see page 39)
Step 2: Connecting the camera to your computer (see page 39)
Step 3: Downloading images/video clips (see page 40)
E
System requirements
(Windows)
System requirements
(Macintosh)
CPU
Pentium 166 MHz processor
or higher
PowerPC G3/G4
OS
Windows 98/98SE/Me/2000/XP
OS 8.6 or later
Memory
32MB RAM
32MB RAM
(64MB recommended)
(64MB recommended)
Free Space on
Hard Disk
128 MB hard disk space
128 MB hard disk space
Required
Devices
A CD-ROM drive
An available USB port
An available USB port
A CD-ROM drive
Color Monitor
Color monitor (800x600, 24-bit
or higher recommended)
Color monitor (800x600, 24-bit
or higher recommended)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Installing the USB driver on Windows computers
The USB driver on the supplied CD-ROM is exclusively for Windows 98. Installing the
USB driver on computers running Windows 2000/ME/XP is not necessary.
1. Insert the CD-ROM packaged with the camera
into the CD-ROM drive. The welcome screen
appears.
2. Click “Install USB Driver”. Follow the on-screen
instructions to complete the installation. After the
USB driver installation is complete, restart your
computer.
E
Installing the USB driver on Macintosh computers
Mac OS 8.6 users must install a USB driver. For Mac OS 9.0 or higher, the com-
puter will automatically recognize the camera and load its own USB drivers.
1. Insert the CD-ROM packaged with the camera into the CD-ROM drive.
2. Select and double-click “Digital Camera Driver Installer “.
3. Select “Install Location” and click “Install”.
4. Follow the on-screen instructions to complete the installation and restart your
computer.
Step 2: Connecting the camera to your computer
1. Connect one end of the USB cable to an
available USB port on your computer.
2. Connect the other end of the USB cable to the
USB connector on the camera.
3. Turn the camera on.
I “PC” appears on the camera’s status LCD.
4. Look for a new “removable disk” appearing in
the “My Computer” window. Your recorded images/video clips will be in a
folder on this “removable disk”. (For Mac users, double-click the “untitled”
disk drive on the desktop.)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Downloading images/video clips
When the camera is turned on and connected to your computer, it is considered
to be one disk drive. You can download images/video clips by coping them from
the “removable disk” (“untitled” disk on a Macintosh) to your hard drive or to
another kind of disk.
For computers running Windows
Open the "removable disk" by double clicking on it. Double click on the folder.
Your images are inside the folder(s). Select the images that you want, then
choose copy from the Edit menu. Open the destination location and choose
Paste from the Edit menu. You may also drag and drop image files from the
camera to a desired location.
E
For computers running Mac OS
Open the "untitled" disk window and the hard disk or the destination location.
Drag and drop from the camera disk to the desired destination.
• It is recommended that you use the AC power adapter as a power supply for the
camera while transferring images/video clips from the camera to you computer since
camera power maybe cut off unexpectedly if the batteries run out.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING MGI PHOTOSUITE
MGI PhotoSuite is a very user-friendly image-editing program. With PhotoSuite,
you can easily retouch, compose and organize your images. It contains a
variety of templates, such as photo frames, birthday cards, calendars and more.
Get your images ready and go explore this amazing program.
To install MGI PhotoSuite:
1. Insert the CD-ROM packaged with the camera
into the CD-ROM drive. The welcome screen
appears.
2. Click “Install MGI PhotoSuite.” Follow the on-
screen instructions to complete the installation.
E
•
•
•
To use MGI PhotoSuite to edit and retouch your recorded images, please refer to the
on-line help of this software as a guide.
For Windows 2000/XP users, make sure to install and use the MGI PhotoSuite in the
“Administrator” mode.
PhotoSuite is not supported on the Mac.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING MGI PHOTOVISTA
MGI PhotoVista is an easy-to-use program that lets you create spectacular 3600
panoramic images in a snap. When you view these panoramas, you get the
experience of being totally immersed in a realistic environment. PhotoVista’s
powerful engine quickly and automatically stitches images together, and its
intuitive interface will let even a novice get great
results in minutes.
To install MGI PhotoVista:
1. Insert the CD-ROM packaged with the camera
into the CD-ROM drive. The welcome screen
appears.
2. Click “Install MGI PhotoVista.” Follow the
on-screen instructions to complete the installation.
E
•
•
•
To use MGI PhotoVista to create spectacular 3600 panoramic images, please refer to
the on-line help of this software as a guide.
For Windows 2000/XP users, make sure to install and use the MGI PhotoVista in the
“Administrator” mode.
PhotoVista is not supported on the Mac.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE USER’S MANUAL
In an effort to conserve energy and preserve our
world’s forests and wildlife, this manual is only
provided on the CD-Rom in PDF format. We
suggest you read through the instruction manual
and print only those pages you need for future
reference. The only requirement for viewing the
User Manual on the CD ROM is that you have
Acrobat Reader installed on your computer.
For Windows users:
1. Insert the CD-ROM that came with the camera into your CD-ROM drive.
The welcome screen appears.
2. Click “Install User’s Manual”. Follow the on-screen instructions to complete
the installation.
E
For Mac users:
1. Insert the CD-ROM packaged with the ca-mera into your CD-ROM drive.
2. Select and double-click “Manual”.
3. Select and double-click the language you prefer.
4. Drag and drop the PDF file from the current location to the destination
location. View the user’s manual by opening it.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING ACROBAT READER
For Windows users:
1. Insert the CD-ROM that came with the
camera into your CD-ROM drive. The welcome
screen appears.
2. Click “Install Acrobat Reader.” Follow the on-
screen instructions to complete the installation.
For Mac users:
1. Insert the CD-ROM that came with the ca-mera into your CD-ROM drive.
2. Select and double-click “Acrobat Reader”.
3. Select and double-click the language you prefer.
4. Double-click “Reader Installer”.
E
5. Follow the on-screen instructions to complete the installation.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPTIONS
Record menu
You can use the record menu to change LCD brightness, white balance EV
compensation, Quickview, digital zoom, flash on/off and sharpness settings. To
do this, press the
options by using the
button in the
button.
mode. And then scroll through the
/
LCD BRIGHTNESS
This option adjusts the brightness of the LCD
monitor. Press the OK button, the LCD bright-
ness control will appear. Press the
button to brighten the LCD monitor while press
the button to darken the LCD monitor.
/
/
E
And then press the OK button.
QUICK VIEW
You can view each captured image on the LCD
display immediately after capture by enabling
Quick View. Each captured image will be
displayed briefly, after which the camera returns
to the
to enable or disable the instant review by press-
ing button. And then press the OK button.
mode automatically. Set [ON] or [OFF]
/
DIGITAL ZOOM
You can take digital zoom shots by activating the digital zoom function. Use the
/
button to enable this option if necessary. And then press the OK button.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
WHITE BALANCE
Your camera adjusts the white balance of each scene automatically. However,
the images that your camera captures will appear different under different light-
ing conditions (sun, shade, fluorescent, tungsten lights). Unlike your eyes, which
can easily adjust to different lighting conditions (lighting temperatures), a digital
camera cannot always differentiate between lighting types. Under some light-
ing conditions the image may appear in strange shades. If that occurs you may
change the white balance setting by specifying a lighting condition (temperature)
most appropriate for your scene.Use the
/
button to select the appropriate
white balance and then press the OK button.
[AUTO]: automatically adjusting the
[SHADE]: for cloudy and shady sky
[FLUORESCENT]: for under fluorescent
lighting
white balance
E
[SUN]:
for outdoors on a bright day
EV COMPENSATION
Your camera adjusts the exposure of each scene automatically. However, when
if the subject is very dark, or very bright, you may override the camera automat-
ic exposure determination to make the subject brighter or darker. This is called
EV compensation. The EV compensation of the camera can be adjusted
from -1.8EV to +1.8EV. Use the
/
button to select the EV compensation that
you want and then press the OK button. To increase image exposure (or bright-
ness), increase the EV compensation. For example, if you want to take a
picture of a dark subject against a bright background, you may want to increase
the EV compensation so the subject is properly exposed. For lighter objects
against a dark background, you may want to reduce the EV compensation. We
recommend taking some test pictures and comparing the results using
different EV compensation settings
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARPNESS
This option sets the level of image sharpness. Use the
/
button to select
the sharpness mode that you want and then press the OK button.
[NORMAL]: leave the image detail as captured
[SOFT]: soften the edge of the image detail for special effect
[HARD]: sharpen the edge of the image detail
FLASH ON/OFF
This option allows you to turn the camera’s flash on or off. This is the only way
to turn the flash on or off when inside the underwater housing.
EXIT
This option exits the record menu and then returns to the
OK button to exit. You can also press the button again to exit.
mode. Press the
E
• EV Compensation adjustments can only be made before taking a picture,
not after.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback menu
Use the playback menu to create an on-camera slide show, configure DPOF
settings, transfer images from internal memory to a memory card, adjust LCD
brightness, or “delete all” images. To access the playback menu, press the
button in the
button.
mode and navigate through the options by using the
/
LCD BRIGHTNESS
Refer to LCD BRIGHTNESS in Record menu.
(See page 50 )
SLIDE SHOW
Your camera can display your images sequen-
tially as a slide show at a selected interval. Use
E
the
/
button to select the slide interval time
you desire and then press the OK button.
[2 sec], [4 sec], [6 sec], [8 sec], [10 sec]
COPY TO CARD
This feature allows you to copy your images from the camera’s internal
memory to an SD memory card. Of course, you can only do this if you have an
SD memory card installed and some images in internal memory. Use the
button to select [YES] if necessary and then press the OK button.
/
DELETE ALL
This option allows you to delete all images/video clips the memory. If you wish
to delete the images or video clips in the internal memory, ensure that the
memory card is not inserted in the camera. Otherwise, you will delete the
images or video clips stored in the SD memory card.
Use the
/
button to select [YES] if necessary and then press the
OK button.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
DPOF
DPOF allows you to embed printing information on your memory card. Using
DPOF you can select an image to be printed and then specify how many prints
to you would like. Take your memory card to a DPOF enabled printer that
accepts SD memory cards. The DPOF/card-compatible printer will read the
embedded information on the memory card and print your images as specified.
To use DPOF, first press the OK button to enter the DPOF sub-menu. Use the
/
button to set the values for each field and then press the OK button.
[PRINT QUANTITY]: Select image quantity from 1~9
[PRINT SIZE]:
Select your preferred image size
(standard, 3x5, 4x6, 5x7, 8x10)
[PRINT INDEX]:
allows you to print the images in index format
E
[PRINT ENABLE]:
If you select ENABLE, the camera will save the DPOF
settings. If DISABLE is selected, all the settings will
be erased.
DPOF shortcut
You can use the shutter button to quickly establish DPOF settings, as follows:
1. Turn the mode dial to the
mode.
2. Press the shutter button to toggle the DPOF print tag setting for the
specified image. A DPOF icon will appear to the right of the image #, which
means the DPOF print tag is set for the specified image.
• When using the shutter button to enable the DPOF setting, the default
setting is size=standard, and quantity=1.
EXIT
This option exits the record menu and then returns to the
mode. Press the
OK button to exit. You can also press the button again to exit.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie menu
To adjust movie menu setting, press the
gate to the option you wish to set by using the
button in the
button.
mode and navi-
/
LCD BRIGHTNESS
This option adjusts the brightness of the LCD
monitor. Refer to LCD BRIGHTNESS in Record
menu for detailed information.
E
EXIT
This option exits the movie menu and then returns to the
mode. Press the
OK button to exit. You can also press the button again to exit.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menu
Select between Land & Sea exposure programs and other general camera pref-
erences in the SET-UP mode. Switch the mode dial to the SET-UP mode and
navigate to the option you wish to configure by using the
/
button.
®
LAND & SEA EXPOSURE PROGRAM SETTING
This unique camera offers the option to set the exposure program for land or sea
(underwater use)
Land: select LAND mode when using camera on land
(above water)
E
Sea:
select SEA mode when using camera (inside underwater
housing) underwater
Flash: select FLASH mode when using camera (inside underwater
housing) with one or two external flash (es)
• Camera is not waterproof and requires the use of the underwater housing
when in or around water
• To confirm Land & Sea Exposure program is set correctly, switch the mode
dial to
mode
• The bottom left of LCD will display one of the above 3 icons
DATE/TIME
Press the OK button to enter the DATE/TIME
sub-menu. Refer to section in this manual titled
SETTING THE DATE AND TIME for further detail.
After removing the batteries from the camera,
the date and time will return to the default set-
ting. If this happens, reset the date and time
when using the camera.
[YEAR], [MONTH], [DAY], [TIME]
51
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE
This option allows you to select the language for the menus and the text dis-
played on the LCD monitor. Press the OK button to enter the LANGUAGE sub-
menu. And then select the preferred language using the
press the OK button.
/
button and
[ENGLISH], [Français], [Deutsch], [Español], [Italiano], [
], [ ],
[
]
SOUND
The camera produces a sound (beep) each time you press the camera button if
this function is enabled. Select [ON] or [OFF] by using the
/
button and then
press the OK button.
E
FORMAT MEDIA
This utility formats the internal memory (or memory card) and erases all stored
images and data. If you select [YES] with the button and press the OK
/
button, the FORMAT MEDIA message appears on the LCD monitor. When you
select [YES] and press the OK button again, a progress bar displays, showing
the progress of the format. This utility formats the internal memory (or memory
card) and erases all stored images and data.
VIDEO MODE
This option allows you to view your images on a TV. Connect the camera to
your TV using the video cable. Then select the video output format by using the
/
button and press the OK button.
[NTSC] : select this format when located in the U.S.A., Canada, Japan, Korea,
Taiwan, Central America, Mexico, etc.
[PAL]
: select this format when located in Australia, Austria, Belgium, China,
Denmark, Finland, Germany, Great Britain, Holland, Italy, Kuwait,
Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland,
Thailand, Norway, etc.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO POWER OFF
If there is no camera activity (no buttons are pressed) for a defined period of time
while the camera is powered on, the camera will switch to an idle mode, and
eventually turn itself off to conserve power.
Inactivity period
(batteries)
Inactivity period
(AC power adapter)
Camera status
90 seconds
3 minutes
90 seconds
30 minutes
stay idle
shut off
If the camera is idle, re-activate the camera by pressing any button or switch the
mode dial. If the camera has powered-off you must to turn the camera on again
by pressing the
button. The table (above) shows the default time settings for
E
idle, and power-off. You can change the power saving interval by using the
/
button and then press the OK button.
[3 min], [5 min], [10 min], [30 min]
RESET TO DEFAULT
If you wish to restore all camera settings to their original status, select [YES] by
using the button and then press the OK button.
/
The following table shows the default setting for each item.
Item
Description
Image resolution
Image quality
Flash
1600x1200 pixels
Fine
Auto
Quick view
On
White balance
EV compensation
Slide show delay
Auto power off
Auto
0.0
4 seconds
Battery: 3 minutes
AC power adapter: 30 minutes
Sound
On
Off
On
Digital Zoom
LCD monitor
53
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE CAMERA TO OTHER DEVICES
E
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA SPECIFICATIONS
Item
Description
Sensor
2.1megapixels 1/3.2” CCD
24 bits (8 bits x 3 colors)
1600x1200 pixels / 800x600 pixels
1.6" color TFT LCD
Color depth
Resolution
LCD
Self-timer
Shutter speed
10 seconds delay
1/10 sec.~1/1000 sec. (Will vary depending
on Land & Sea exposure program setting)
Zoom
2 x digital zoom
Capture modes
Memory type
Still photographs or video recording
8 MB internal memory / SD memory card
(optional) (up to 256MB capacity)
E
Memory capacity
Storage for an 8MB SD memory card at
1600x1200 pixels: Fine: 10 images;
Normal: 15 images; Basic: 20 images
Flash effective range
Lens
0.5m~2.5m
Fixed focal length: 5.6mm
Focal range: Standard—0.7m~infinity;
Macro—0.3m~0.8m / F-number: 2.8/5.6
Focus
Focus range: 30cm to infinity
Exposure compensation
Exposure programs
White balance
Compressed format
Standards
Auto; Manual: -1.8 ~ +1.8EV (0.3EV step)
Land, Sea or External Flash
Auto, Sun, Shade, Fluorescent, Tungsten
JPEG, Motion JPEG for video clip
JPEG, EXIF 2.1, DPOF, DCF, Motion JPEG
Interface
DC IN jack, USB connector, VIDEO OUT
jack (NTSC or PAL)
Operating environment
Power
Operation: 0˚C~40˚C, 15~90% humidity
Storage: -20˚C~80˚C, 10~95% humidity
2
AA Alkaline (1.5V) or Ni-MH (1.5V)
batteries, or AC power adapter(2.5A/3.3V)
Tripod socket
Dimensions
Yes
112 x 41 x 56 mm (W x H x D)
(4.4” x 1.6” x 2.2”)
Weight
Approx. 150g (without batteries and the
SD memory card) 5.2 ounces, (7.3 ounces
with battery and SD card
*Design and specifications are subject to change without notice.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Underwater Housing Instructions
Important: Please carefully read and understand these instructions before
using camera and housing underwater.
SeaLife Reefmaster Dive Easy
Housing (SL113)
• Depth rated and tested to 200ft. (60M)
• Fully rubbered armored for water and
shock protection
• Includes Sportsfinder.
• Soft rubber grips.
• Optical glass lens port.
E
• Stainless steel hardware - corrosion
proof.
Front view of
DC250 housing
•
3-button controls ( power, shutter and
LCD on/off).
• Accessory mount for adding one or
two external flash (es)
• Snap-on lens port to quickly attach
macro or wide angle lens.
• Leak check window let’s you see if
housing leaks while underwater.
Back view of
DC250 housing
56
Download from Www.Somanuals.com. All Manuals Search And Download.
MUST DO for underwater housing:
1. Read these instructions before using the underwater housing.
2. Do not exceed the depth rating printed on the lens port of the housing.
3. Keep main O-Ring perfectly clean.
• Clean main O-ring with cleaning brush provided before every use. Do not
remove O-ring. Do not grease O-Ring.
• Store camera and housing only after careful cleaning and when totally dry.
• Housing uses one large O-ring at housing sealing lid. Never use housing
without O-ring in place.
• If O-ring is damaged, contact the SeaLife Service Center. (See page 58).
Do not continue using housing
• O-ring must be perfectly clean (no sand, dirt or debris) before sealing
housing.
E
• Soak or rinse sealed housing with fresh water after use in salt water.
4. Carefully close lid to seal housing.
• Make sure O-ring do not slip out of the groove when sealing.
• Press lid firmly and tightly down into housing to ensure a waterproof seal.
5. Never let any moisture or dirt get inside housing when opening.
• Only open and load the housing in dry cool air, such as inside an
air-conditioned room.
6. For great underwater pictures you need:
• Clear water conditions, control your buoyancy before taking picture, get
as close as possible to subject (ideal distance is 2’ to 6’). Use the SeaLife
Macro Lens/Filter for close-up pictures with super details and vibrant
colors.
7. Store housing at room temperature in a clean and dry place
• Do not expose housing to direct sunlight for prolonged periods of time.
• Do not store housing in hot locations, like the trunk of your car.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Open view of housing
The housing uses one O-ring to
form a waterproof seal
Contact SeaLife Service Center if
O-ring is damaged and requires
replacement.
E
Important: Carefully inspect o-ring for salt, sand, hair, cuts, tears or other
damage. Clean o-ring before every use. Replace o-ring if damaged.
If O-ring needs to be replaced, contact the SeaLife Service Center
at (856) 866-9192
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Main O-ring and keeping a waterproof seal
The SeaLife housing uses one O-ring to form a waterproof seal. Every housing
is tested for quality and a waterproof seal. It is your responsibility to maintain the
housing and ensure it remains waterproof. Our research and testing shows that
99% of leaks are the result of not cleaning or caring for the O-ring.
Warranty does not cover a water-damaged camera unless it is clearly
determined that a manufacturing defect caused the leak.
• The O-ring must always be kept clean and checked for damage before
every use.
• Carefully clean the housing surface that makes contact with the O-ring and
inspect for scrapes and cuts. If the housing sealing area is damaged, contact
the SeaLife Service Center.
• Never use the housing without the O-ring in place.
• If O-ring need replacement contact the SeaLife Service Center.
• Do not remove or lubricate the O-ring.
E
• The O-ring located in the housing lid groove is not glued in place. O-ring
should not be removed unless sand, hair or other objects become trapped
under O-ring. If O-ring must be removed use the other end of the cleaning
brush to lift up O-ring and remove. Carefully inspect O-ring for cuts and
damage. If this O-ring is removed, make sure it is carefully replaced. Do
not twist or stretch O-ring. O-ring must be pushed into it’s groove. Be
careful not to pinch O-ring when closing housing.
The underwater housing uses 3 buttons – Power, Camera, LCD Power button
and Shutter button. Each button assembly has an O-ring to keep a waterproof
seal. It is normal to feel some resistance when pressing these buttons. If the
button does not return to it’s original position or if the button does not have a
smooth action, contact the SeaLife Service Center. Do not attempt to
disassemble or service the shutter or power buttons.
Quick waterproof test
Wrap a small dive weight in a blue paper towel, place inside housing and close
the lid to seal the housing. The blue paper towel makes it easier to see a leak.
Make sure not to pinch the paper towel in the O-ring. Place the sealed housing
in a tub of cold water for about one hour. No leaks should be present. If the
housing shows sign of leaking, do not use the housing and contact the SeaLife
Service Center for repairs.
SeaLife Service Center, 97 Foster Road, Moorestown, NJ 08057
59
Download from Www.Somanuals.com. All Manuals Search And Download.
SeaLife ReefMaster Underwater Camera Housing
Front View
E
60
Download from Www.Somanuals.com. All Manuals Search And Download.
SeaLife ReefMaster Underwater Camera Housing
Rear View
E
61
Download from Www.Somanuals.com. All Manuals Search And Download.
How to set-up the Underwater Housing
Set up camera
1. Insert 2 fully charged Ni-MH batteries (size AA, capacity at least 1800 mAh).
See page 67 for more battery information. Make sure you insert the batteries
with the correct + and – polarity.
2. Clean camera lens with dry, clean cotton cloth.
3. Make sure camera focus lens is set to normal distance. DO NOT SET TO
MACRO.
4. Remove camera strap since this may prevent the camera from correctly
seating itself inside the housing.
5. Set camera to Sea mode. If you are using an External Flash, set camera to
External Flash mode. See page 51 for detailed instructions on how to set
camera to Land, Sea or External Flash modes.
E
Set up housing
Opening and loading of the housing should be done only in dry cool air,
such as in an air-conditioned room to prevent fogging.
1. Open the housing by pulling up latch on side of housing. Do not extend
housing lid beyond its stop point or damage may occur to the hinge area.
2. Carefully inspect O-ring for damage and make
sure O-ring is firmly seated in its groove.
If O-ring is damaged and requires replacement,
contact SeaLife Service Center (For service
details, see page 58).
To OPEN:
Push
up
rubber
grip
3. Clean the housing glass lens port using clean,
dry cotton cloth. It is recommended to apply
anti-fog solution to the inside surface of the
housing lens.
Pull up
latch
4. Carefully insert camera into housing. Make sure
camera is clean and dry.
5. Insert two Anti-Fog desiccant capsules into special slots inside housing.
Note: New desiccant capsules will be blue in color. As the desiccant absorbs
moist air, it turns from blue to light pink. Replace desiccant capsules when
color changes to light pick.
6. Carefully clean O-ring and inside of housing area where O-ring makes
contact. Use cleaning brush provided in Care Kit. O-ring must not be wet
when sealing housing, allow these areas to dry.
O-Ring must be absolutely clean of all lint, sand or other small particles.
Do not grease O-ring.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Do not allow any water droplets to get
inside housing. This will cause the
inside of the housing to fog.
13. Close housing lid tightly. Make sure
there are no obstructions that prevent
the housing from closing. Make sure lid
is tightly pressed into housing, ( see
picture).
14. Close housing latch. Make sure the lid
is pressed flat and evenly against the
housing body. The housing may leak if
the lid is not flat against the housing
when closed.
Close housing lid tightly, then close
latch.
E
Test camera and housing
1. Press the external power button on the top of the housing to turn camera
power on.
2. Press the shutter button on the outside of the housing to take a test picture.
3. The power or shutter button should have a smooth action and return to its
original resting position after pressing. It is normal to feel some resistance
when pressing the power and shutter button.
4. Press and hold power button to turn camera power off. It is recommended
to leave camera power off until you’re ready to use camera to preserve
battery power.
5. After 3 minutes the LCD and monitor will turn off, and the camera will in power
save mode. To re-activate power, push the SHUTTER BUTTON.
6. After 15 minutes the camera power will shut down. To operate the camera,
push the POWER BUTTON to turn on the camera.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using and cleaning the underwater housing and camera
Entering the water with housing
1. Do not enter water with camera in your hand. Have someone hand you the
camera after you have entered the water.
2. See “Great Pictures Made Easy” on page 65.
After using housing underwater
1. Before entering dive boat, hand housing to someone on the boat.
2. Make sure the sealed housing is placed in a fresh water tank available on
most dive boats. This will clean the salt water from the camera housing
and prevents the salt water from drying on the camera housing and O-ring.
Never let water dry on the camera housing. Salt crystals can damage the
O-ring, lens and attract moisture. Dry housing with clean soft towel after
removing from fresh water tank.
E
3. Do not expose camera and housing to direct sunlight – keep in a shaded area
or under a dry towel.
4. It is not recommended to remove camera from housing while on the dive
boat. Allowing humid air to enter the housing may cause fogging.
5. If you must open the housing while on the dive boat, make sure you and the
housing are perfectly dry before opening the housing. Do not allow the inside
of the housing or the camera to get wet.
Cleaning housing after use
1. The sealed housing must be thoroughly cleaned with fresh water before
opening. Never let salt water dry on housing. Salt crystals may damage the
O-ring, lens and attract moisture.
2. Never let water drops dry on lens. Wipe lens dry with clean cotton cloth.
3. Before opening housing, everything, including your hands, head and
surrounding area must be totally dry. Have a dry towel handy.
4. After opening the housing, clean the camera, O-ring area and all inside and
outside parts with a clean, dry cotton cloth.
5. Before storing the housing and camera, remove batteries, SD card and keep
in a clean dry area. Make sure the housing and any accessories are clean
and dry before storage.
6. Never store camera or housing in direct sunlight or in a dark damp area. The
airtight, unbreakable SeaLife ReefMaster Dry Case (Item # SL930) is highly
recommended along with 1-oz bags of SeaLife Moisture Muncher Desiccant
(Item # M101) for travel and storage.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Great Pictures Made Easy
Taking underwater pictures is much different that taking land pictures. Here are
the most important tips to taking great pictures underwater:
1. Crystal Clear water.
Crystal Clear water is essential for good underwater pictures. Remember the
human eye can see more detail than a camera. In other words, your eyes
see the water as being clearer than it actually is. Floating particles like algae,
and silt cause low visibility. Avoid stirring up the sandy bottom with your fins.
These floating particles cause small spots to appear in your picture, known
as “backscatter.”
Always remember to limit your shooting distance to 1/10 of the water visibility.
For example, if the visibility is 60 feet (18 m), you should keep your shooting
distance to within 6 feet (1.8m); in 30 feet (10 m) visibility you should be no
further than 3 feet (90 cm) away from your subject.
E
2. Stay within the ideal shooting distance of 2 to 6 feet.
The ideal shooting distance is between 2 to 6 feet (0.6 to 1.8 meters). This
distance will result in detailed, colorful pictures. The closer, the better. Use your
stretched out arm as a measuring tool to keep your minimum shooting distance
of 2 feet (0.6 meters). Remember that light does not travel very far underwater.
For best pictures, use a 3X Macro Lens at distances from 12 to 36 inches
(30 to 90 cm).
3. Move calmly and control your buoyancy before taking a picture.
It is very hard to take good pictures when you are moving. Look around for great
picture opportunities. First position yourself at the best angle, and neutralize
your buoyancy. Second, use the LCD monitor to perfectly frame your subject,
check your shooting distance and keep the camera steady. Third, be calm and
patient: Sometimes you have to wait a little bit so the fish that were frightened
away, come back. Don’t chase the fish, let the fish come to you.
Always be in control of your buoyancy before taking pictures and observe
all safe-diving rules.
4. Shoot and review - If you don’t like it, delete it.
One of the key advantages of the SeaLife digital camera is that the monitor displays
the picture you’ve just taken. The monitor will display a message “DELETE THIS?” for
3 seconds. If you don’t like it, delete it by pushing the shutter button again. One of
the best ways to learn underwater photography is from your good pictures and
mistakes.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Take several pictures of the same subject.
Use different distances and angles. (Allow about 10 seconds between shots for the
flash to re-charge). Study and compare the good and bad pictures and you will soon
be a master.
Never touch any sea creatures. Consult your dive master about approaching
dangerous creatures or structures.
6. Use SeaLife Macro and Wide Angle Lenses for dramatic
close-ups.
The SeaLife Macro and Wide Angle lenses allow you to get super close to your sub-
ject for images full of colors and razor-sharp details. Each SeaLife macro lens has
optical coatings for color correction (reduces the underwater bluish effect) and a neu-
tral density coating to prevent over flashing.
With the 24mm wide-angle lens you fit a close group of 4 dive buddies or a 6-foot (180
cm) shark at a shooting distance of 6 feet (180 cm). Normally you would have to be
10 feet away, too far for a sharp picture. The following lenses are available at your
local scuba dive dealer:
E
Lens description
No Lens
Item #
Effective range
N/A
2’ (60 cm) to infinity
22" to 36" (56 to 90 cm)
16" to 22" (40 to 56 cm)
8" to 11" (20 to 28 cm)
Macro 3X lens/filter
Macro 8X lens/filter
Macro 16X lens/filter
SL951
SL959 (set)
SL959 (set)
24 mm Wide angle lens SL970
1’ (30 cm) to infinity
Field of view about 50% larger.
The above distance only apply to digital camera. SeaLife film cameras will have different
shooting distances.
The 8X and 16X Macro lenses are sold in a set that also includes the extendable and
collapsible distance-measuring device “Macro Wand” (Set item # SL959)
7. Use the SeaLife External Flash to enhance color and brightness.
Water filters out light and red/yellow colors resulting in darker, bluer images. The only
way to prevent this from occurring is by taking pictures at shallow depths (within 5’
depth on a sunny day) or by using artificial light, like the SeaLife External Flash.
The External Flash easily mounts to the bottom of the housing. The flexible arm allows
you to direct the flash at the subject. Even two flashes can be mounted onto the
housing for an evenly illuminated and shadow-free image. This system blocks the
built-in flash and prevents backscatter. The flexible flash arms allow quick
adjustments of the flash. An optional Flash Diffuser can be snapped onto the flash
head and is highly recommended for close-up shots of bright, reflective subjects.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
8. The quick review feature allows you to playback pictures without
removing the camera from the housing.
Press and hold the LCD button for 2 seconds. The last image will appear. Press
the LCD button to scroll to the next picture. Press and hold the LCD button for
2 seconds to exit.
Battery Selection Guide:
It is important to use only AA batteries designed for high drain electronic
devices.
Nickel Metal Hydride (Ni-MH)
We suggest using SeaLife 1800 mAh Ni-MH rechargeable batteries or higher
mAh rated Ni-MH battery. With Ni-MH batteries, you can expect about 2 hours
of normal operating usage. Ni-MH batteries can be recharged about 1000 times
without the “memory” problems that you get with Ni-CAD batteries
With proper power management you can get through a dive day and recharge
your batteries at night.
E
Do not expose Ni-MH batteries to water or moisture. Properly dispose of any
Ni-MH battery exposed to water or moisture.
See specific warning on battery.
Lithium
Lithium AA batteries are suitable for the SeaLife digital camera. AA Lithium
batteries typically will last the longest, cost the most and are not rechargeable.
Standard and High Energy Alkaline
Do not use alkaline batteries, like Duracell Coppertop, since they may only last
about 10 minutes in the SeaLife Digital Camera.
If you cannot use Ni-MH rechargeable batteries, you may use new “high
energy” alkaline batteries that last a longer than standard alkaline batteries, but
not as long as SeaLife Ni-MH rechargeable batteries. The following are
examples of “high energy” alkaline batteries:
1. Duracell Ultra
2. Panasonic (high energy)
3. Energizer Titanium or E3 (High Energy)
Do not attempt to recharge alkaline batteries.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Life
We have tested the following batteries under normal and extreme operating
conditions. The following operating times are averages and can vary depend-
ing on age of battery, temperature and other factors.
Normal conditions (designed to simulate operating conditions when scuba
diving):
1. Turn camera on, take a test picture. Set to Sea Mode. Put in housing, close
housing.
2. 90 minutes later: Turn power on. Take three pictures on land. 10 Minutes
later: Take pictures underwater for 45 Minutes, not continuously, but every
2 Minutes, =23 pictures.
3. Wait for 1 hour, then take 20 underwater pictures in 40 Minutes.
4. Wait for 2 hours, then repeat step 2 and step 3.
5. Then repeat 3.
E
Extreme conditions (designed to test the power consumption in the most
extreme operating conditions.)
1. Turn camera on, Set to External FLASH mode. Put in housing, close housing.
2. Take picture intervals as quickly as possible (display always ON, FLASH
always fires)
Battery
Type
Life during
NORMAL use
Life during
EXTREME usage
SeaLife Ni-MH rechargeable (1800mAh)
Energizer Lithium 1 (non-rechargeable)
Duracell Ultra (high-energy alkaline)
Duracell Coppertop (Standard alkaline)
200 minutes
400 minutes
200 minutes
20 minutes
100 minutes
130 minutes
60 minutes
10 minutes
Note: The above times may vary depending on other factors like temperature,
humidity, age of batteries and other factors.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble shooting guide
Problem
No Power
Possible cause
Corrective Action
Battery power low. . . . . . . . . . . Replace or recharge batteries.
Wrong type of batteries. . . . . . . Use only AA designed for high
drainage electronics.
(see battery selection guide)
Battery + and - not inserted
correctly. . . . . . . . . . . . . . . . . . . . . Check that batteries are inserted
. . . . . . . . . . . . . . . . . . . . . . . . . correctly.
Power save function activated.. Turn camera back on.
Camera damaged . . . . . . . . . . . Contact service center.
Constant use of camera.. . . . . . This is normal.
Using incorrect battery type.. . . Use only AA designed for high
drainage electronics.
Camera gets hot
No PC connection
(see battery selection guide)
USB cable not connected
E
to USB port. . . . . . . . . . . . . . . . Inspect connection ports.
Slow PC connection time.. . . . . Give at least 5 minutes for some
. . . . . . . . . . . . . . . . . . . . . . . . . PC’s to establish connection.
Camera driver not installed . . . . Install camera driver CD
(page 39).
No Video Connection
Improper connection to TV . . . . Connect video cable to video IN
jack of TV or VCR and change
TV/VCR to video in channel.
Poor Video connection Video cable not fully inserted
into camera or TV . . . . . . . . . . Make sure video cable is
completely inserted into video
jack of camera until it clicks.
Also check that connection to
TV/VCR is correct.
“Memory full” message Memory storage is full. . . . . . . . Delete images or download to
PC. Insert empty CF card.
Pictures out of focus
Dirty lens. . . . . . . . . . . . . . . . . . Clean lens with clean cotton
cloth.
Incorrect focus setting. . . . . . . . Check lens for correct
focus (macro or standard).
Fogged housing lens. . . . . . . . . Insert camera in dry, air-condi-
tioned room. Use anti-fog
desiccant inside housing. Do
not let water drops get inside
housing.
Too close to subject.. . . . . . . . . Shooting distance must be 2’+
(macro = 1’ to 2’).
Low water visibility . . . . . . . . . . .Shooting distance not to exceed
1/10 of visibility.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Grainy picture
Possible cause
Dark light conditions. . . . . . . . . Move closer to subject
(2’ to 6’). Use SeaLife External
Corrective Action
Flash to illuminate subject and
improve color and brightness.
Overexposed image
Flash not firing
To close to reflective object. . . . Move farther away from sub-
ject (4’ to 6’). Turn External
Flash away from subject. Use
External Flash Diffuser
(SL968).
Flash on Auto and is
not needed. . . . . . . . . . . . . . . . .Turn fill-flash ON (see page 30)
Finger over flash window . . . . .Grip camera correctly, not
blocking flash.
Improper operating mode . . . . .Check for proper operating
mode (Land or Sea).
E
Lost images
Defective SD card. . . . . . . . . . . Use only approved quality SD
cards. Reformat SD card (will
delete pictures).
Defective internal memory. . . . . Reformat memory (this will
delete pictures in memory).
Using camera with low
battery power. . . . . . . . . . . . . . .Replace with freshly charged
batteries.
Image number indicator
does not count down
This may occur depending on .
actual memory available. . . . . . N/A
Housing leaks water
O-ring not clean or
is damaged. . . . . . . . . . . . . . . . Perfectly clean main O-ring.
. . . . . . . . . . . . . . . . . . . . . . . . . Inspect for damage or dents
to housing and O-ring.
Replace damaged O-ring.
Camera not seated in hous-
ing. Remove strap or any
accessory from camera.
Check that camera is com-
pletely seated in housing.
No image on TV set
Improper connection. . . . . . . . . Check cable connections.
Wrong video mode.. . . . . . . . . . Change video mode in cam-
era set-up menu (page 52).
70
Download from Www.Somanuals.com. All Manuals Search And Download.
E
71
Download from Www.Somanuals.com. All Manuals Search And Download.
|