CLP27DN/ CLP31DN/ C7526dn/ C7531dn/ LP226cn/
LP231cn/ Aficio SP C410DN/ Aficio SP C411DN
Quick Installation Guide
Read this manual carefully before you use the product and keep it handy for future reference.
For safe and correct use, please be sure to read the Safety Information in“Safety Information”
before using the machine.
Turn the two green levers
counterclockwise ( ), and then slowly
open the inner cover ( ).
Remove the protective sheet, as shown.
Pinch the orange tape, and then pull it
out.
❖
Optimum Environmental Conditions
Checking the Contents of
the Box
Unpacking
Where to Put the Printer
Permissible and recommended temperature and
humidity ranges are as follows:
The printer’s location should be carefully chosen
because environmental conditions greatly affect its
performance.
Follow the procedure below to verify the items that
come with the printer.
To protect it from shock and vibration during transit,
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
Warning
• Ensure that the box contains all items listed below. If
there are any missing or defective items, contact your
sales representative.
•
•
Confirm that the wall outlet is near the machine and
freely accessible, so that in event of an emergency, it
can be unplugged easily.
Caution
•
•
When lifting the machine, use the inset grips on both
sides. The printer could break or cause an injury if
dropped.
❖
Manuals and CD-ROMs
Quick Installation Guide (This manual)
CD-ROM “Printer Drivers and Utilities”
CD-ROM “Manuals”
Only connect the machine to the power source
described on this manual.
Avoid multi-wiring.
Do not damage, break or make any modifications to
the power cord. Do not place heavy objects on it, pull
it hard or bend it more than necessary.These actions
could cause an electric shock or fire.
The supplied power cord is for use with this equipment
only. Do not use with other appliances. Doing so may
result in fire, electric shock, or injury.
AQC032S
AET806S
Place no objects on the left or inner cover.
Remove the end of the tape from the pinter.
•
•
Turn the green lever clockwise to lock
the unit.
CD-ROM “Document Management Utility”
%RH
Ferrite Core x 2
• Be sure to remove all four strips of tape from the
photo conductor unit to avoid malfunction.
• Removed tape is dirty. Be careful not to let it touch
your hands or clothes.
•
Remove the plastic bag.
Caution
AET510S
•
•
Do not handle the plug with wet hands.Doing so might
cause an electrical shock.
Toner Cartridges: Black (K), Magenta (M), Cyan
(C), Yellow (Y)
TS4K031KE
AET802S
• White area: Permissible Range
• Gray area: Recommended Range
Lift the printer with two people by using
the inset grips on both sides of the printer.
Remove the four pieces of tape from
Keep the machine in an area that is within optimum
environmental conditions. Operating the machine in
an environment that is outside the recommended
ranges of humidity and temperature can cause an
electrical fire hazard.Keep the area around the socket
free of dust. Accumulated dust can become an
electrical fire hazard.
Place the machine on a strong and level surface.
Otherwise, it might fall and injure someone.
If you use the machine in a confined space, ensure
there is continuous air circulation.
the photo conductor unit.
AET146S
Close the inner cover. Lock the inner
cover by pressing in ( ) and then
turning the two green levers clockwise
( ).
• The machine must be level within 5 mm, 0.2˝ from
both front to rear and left to right.
• To avoid possible build-up of ozone, locate this
machine in a large well ventilated room that has an
air turnover of more than 30 m3/hr/person.
• When you use this machine for a long time in a
confined space without good ventilation, you may
detect an odd smell. To keep the workplace
comfortable, we recommend you keep it well
ventilated.
•
•
AET028S
Paper Feed Unit Labels
AET034S
AET803S
Remove the securing pin, as shown,
from the transfer unit. Pinch it, and
then pull it out.
❖
Space Required for Installation
Leave enough space around the printer. This space is
necessary to operate the printer. The recommended (or
minimum) space requirements are as follows:
• Leave the tape holding the paper feed tray and cover
in place while moving the printer.
❖
Space Required for Installation
• Lower the machine slowly and carefully to prevent
trapping your hands.
AQC014S
• Areas exposed to direct sunlight or strong light
• Dusty areas
• Areas with corrosive gases
• Areas that are excessively cold, hot, or humid
• Locations near air conditioners or humidifiers
• Locations near other electronic equipment
• Locations subject to frequent strong vibration
Close the left cover.
AET031S
Close the left cover firmly using both hands, until it
clicks into place.
Color Calibration Sample Sheet
Remove the orange adhesive tape from
the printer body.
Open the top cover by grasping the
handles on the left and right sides.
Open the left cover. Do not remove the
orange tape attached to the left cover.
❖
Power Source
AET804S
Turn the green lever of the transfer unit
counterclockwise to unlock the unit.
Connect the power cable to a power source of the
following specification:
AQC025S
A: 50 cm (19.7 inches) or more
B: 10 cm (4 inches) or more
C: 10 cm (4 inches) or more
D: 70 cm (27.6 inches) or more
• 120 V, 60 Hz, 11 A or more
Additional Documentation
AQC007S
AQC026S
• This package does not include an interface cable.
Purchase one to use with your host computer. See
“Appendix”, Hardware Guide.
AET805S
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Installation Guide 2/2
Quick Installation Guide
Press the {Menu} key.
Selecting the Display
Language
Reading the LED Lamps
Test Printing
Network Connection
Ethernet Configuration
❖
For standard ethernet port
The following explains the procedure for test printing
of the configuration page.
Test printing in order to verify that the printer is working
normally. Test printing checks printer performance
only; it does not test the connection to the computer.
Follow the procedure below to connect the printer to
the computer through the network. Prepare the hub and
other network devices before connecting the 10 BASE-
T or 100 BASE-TX cable to the machine's Ethernet
port.
Make the following network settings according to the
network interface you are using.
You can use SmartDeviceMonitor for Admin or a Web
browser to make IP address-related settings in a TCP/
IP-capable environment.
K
C
M
Y
Select a language using the procedure described here.
The message for the selected language will appear on
the display. If you want to use the display in English,
the following procedures are unnecessary.
Press the {Menu} key.
AQC001S
• The default setting is English.
• Use shielded Ethernet cable. Unshielded cables
create electromagnetic interference that could
cause malfunctions.
• The Ethernet cable is not supplied with this
machine. Select your cable according to the
network environment.
• Configure the printer for the network using the
control panel.
• The following table shows the control panel
settings and their default values.
These items appear in the “Host Interface” menu.
• After configuring the network settings, making
security settings is recommended. For details, see
the “Notes to Administrator” sheet.
K
C
M
Y
Select [Host Interface] using , {▼} or
{▲}, and then press the {OK} key.
AQC070S
Press the {Menu} key.
1. Yellow: comes on when 100BASE-TX is being
used. It comes off when 10BASE-T is
being used.
2. Green: comes on when the printer is properly
connected to the network.
K
C
M
Y
Attach one ferrite core at the printer
end of the Ethernet cable, and then
attach the other ferrite core about 10
cm (4 inches) ( ) from this core.
Setting Name
Value
AQC001S
Auto-Obtain (DHCP) On
Select [Network] using {▼} or {▲}, and
IPv4 Address
011.022.033.044
000.000.000.000
000.000.000.000
Auto
then press the {OK} key.
Select [List/Test Print] using {▼} or
{▲}, and then press the {OK} key.
Subnet Mask
USB Connection
AQC001S
Gateway Address
Frame Type (NW)
Effective Protocol
Select [Language] using {▼}or {▲}, and
then press the {OK} key.
IPv4
Effective
IPv6
Effective
Effective
Effective
Effective
• USB2.0 interface cable is not supplied. Obtain it
separately, according to the computer you are
using.
• USB connection is possible under Windows 98 SE/
Me/2000/XP, Windows Server 2003, Mac OS 9.x,
and Mac OS X.
• Windows 98SE/Me supports USB1.1 speeds.
• USB connection with Macintosh is only possible
via the printer's USB port.
NetWare
SMB
Select [Machine IPv4 Address] using
{▼} or {▲}, and then press the {OK}
key.
AET121S
Select [Config. Page] using {▼} or {▲},
and then press the {OK} key.
AppleTalk
Auto
Connect the Ethernet cable to the
Ethernet port.
Ethernet Speed
LAN Type
Auto
Select the language using {▼} or {▲},
and then press the {OK} key.
Connect the square-shaped connector
of the USB2.0 cable to the USB port.
The configuration page will be printed.
• If Auto Obtain (DHCP) is in use, the IPv4 address,
subnet mask, and gateway address are all set
automatically.
If printing is not normal, check to see if an error
message appears on the display. If there is an error
message, see “Troubleshooting”, Hardware Guide.
Select [Auto-Obtain (DHCP)] using {▼}
or {▲}, and then press the {OK} key.
•
Make this setting only when it is necessary. See
Software Guide.
Check the options.
Press the {Menu} key to return to the
AET122S
For details about the configuration page, see
“Interpreting the Configuration Page”, Software
Guide.
initial screen.
Detecting the Network Address
Automatically (Using DHCP)
Connect the other end of the cable to the
printer's network, such as a hub.
Press the {Menu} key to return to the
The address detected by the printer will appear.
To check the detected addresses, press the followings:
• [IP Add.] : IP address
AET124S
initial screen.
Connect the opposite end's flat
connector to devices such as your
computer's USB interface, or a USB
hub.
• [Subnet] : Subnet Mask
• The printer's ethernet and USB ports are not
available when the gigabit ethernet board is
attached to the printer.
• When you use this printer in DHCP environment,
select [Auto-Obtain (DHCP)] following this
procedure.
• When [Auto-Obtain (DHCP)] is selected, you
cannot make settings for the following items:
• IP Address
Press the {MENU} key to return to the
initial screen.
Print a configuration page to confirm
the settings made.
• For details about network environment settings, see
Software Guide.
• Subnet Mask
• Gateway Address
• Consult your network administrator for information
about making network settings.
• For details about printing the configuration page, see
“Test Printing”.
Download fromCWw
L
w
P
.So
3
ma
0
nuDals.c
N
om/. A
C
ll M
L
an
P
ua
2
ls S
7
ea
D
rchNAnd
/
D
C
ow
7
nlo
5
ad
31dn/C7526dn/LP231cn/LP226cn/Aficio SP C411DN/Aficio SP C410DN
.
Quick Installation Guide
Click [Quick Install]
.
Press the {Escape} key until the screen
Click [Finish].
A message about restarting the computer may appear.
Restart the computer to complete installation.
Specifying a Network
Address
INSTALLINGTHE PRINTER
DRIVER
The software license agreement appears in the
[License Agreement] dialog box.
returns to the [Network] menu.
If you use IPv4, assign the IPv4 address
to the printer. Select [Machine IPv4
Address] using {▼} or {▲}, and then
press the {OK} key.
You can install the printer drivers and software easily
from the CD-ROM labeled “Printer Drivers and
Utilities”.
Press the {Menu} key.
Click [Quick Install] in the window of the CD-ROM
to install PCL and RPCS printer drivers. To install the
PostScript 3 printer driver, click the [PostScript 3 Printer
Driver] button. For more information about the
PostScript 3 printer driver, see Software Guide on the
CD-ROM labeled “Manuals”.
K
C
M
Y
When the TCP/IP protocol is used, SmartDevice
Monitor for Client will be installed as well.
Click [Exit] in the first dialog box of the
installer, and then take out the CD-ROM.
To get the IPv4 address for the printer, contact your
network administrator.
This is an example when English is selected in
When using with TCP/IP protocol, confirm the
followings:
step
.
To specify the IPv4 Address, press [IP
Add.].
The printer is connected to a network with the 5
interface cable.
The TCP/IP protocol is set.
The IP (IPv4) address is set for the printer and the
computer.
AQC001S
After reading through all of the contents,
click [I accept the agreement] to agree with
the License Agreement, and then click
Select [Host Interface] using , {▼} or
{▲}, and then press the {OK} key.
[Next >]
.
If you use IPv4, assign also Subnet Mask and
GatewayAddress. To assign these, press [Subnet M]
or [Gateway] instead.
• To install printer driver under Windows 2000/XP
Professional, Windows Server 2003, and Windows
NT 4.0, you must have an account that has Manage
Printers permission. Log on as an Administrator.
• Only the printer driver, and not the SmartDevice
Monitor for Client is installed when using this printer
under USB or parallel. If you connect using USB,
see Software Guide.
Select [Network] using {▼} or {▲}, and
then press the {OK} key.
Enter the address using {▼} or {▲}, and
then press the {OK} key. settings made.
• To stop installation of the selected software, click
[Cancel] before installation is completed.
• Auto Run may not work with the certain operating
system settings. If this happens, launch “Setup.exe”
on the CD-ROM root directory.
• Select a printer to whose IP (IPv4) address is displayed
in [Connect To] to install SmartDeviceMonitor for
Client when using TCP/IP.
Select the printer model you want to
install in the “Select Printer” dialog box.
Quit all applications currently running.
Press the {▼} or {▲} key to enter the left most entry
field of the address.After entering the left field, press
the {OK} key, and then you can enter the next field.
After completing to enter in the all fields, press the
{OK} key. Use this
Select [Effective Protocol] using {▼} or
Insert the CD-ROM into the CD-ROM
drive.
{▲}, and then press the {OK} key.
• Quick Install is not available unless bidirectional
communication between the printer and computer is
enabled via parallel connection. For details about
bidirectional communication between printer and
computer, see “Printing with Parallel Connection”,
Software Guide.
The installer starts.
Auto Run may not work with the certain operating
system settings. If this happens, launch
“Setup.exe” on the CD-ROM root directory.
method to assign Subnet Mask and GatewayAddress.
• Do not set “011.022.033.044” as the IPv4 address.
• The value moves by 10 if the {▼} or {▲} key is
kept pressed.
Select an interface language, and then click
Select [Specify] using {▼} or {▲}, and
{OK}
.
• For a network connection via TCP/IP, select the printer
whose IP address is displayed in [Connect to].
• For parallel connection, select the printer whose
printer port is displayed in [Connect to].
The default interface language is English.
then press the {OK} key.
Select the network protocol using {▼}
or {▲}, and then press the {OK} key.
Click [Install]
.
The following display appears while installing the
printer driver.
If you do not select [Specify] in this step, the address
you set will not be saved.
Select [Effective] or [Invalid] using {▼}
Press the {Menu} key to return to the
or {▲}, and then press the {OK} key.
initial screen.
Print a configuration page to confirm the
settings made.
• For details about printing the configuration page, see
“Test Printing”.
Set other protocols you need to set in the same way.
• Select [Invalid] for unused protocols.
• Enable IPv4 to use the Pure IPv4 environment of
NetWare 5/5.1, NetWare 6/6.5.
Copyright © 2006
EN
USA
G160-8606
CLP30DN/CLP27DN/C7531dn/C7526dn/LP231cn/LP226cn/Aficio SP C411DN/Aficio SP C410DN Quick Installation Guide 2/2
Download from Www.Somanuals.com. All Manuals Search And Download.
|