LASER POINTER REMOTE CONTROL UNIT
MODEL POA-RCKIT03
Operating Instruction
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instructions. If such changes or modifications should be made, you could be required to stop operation of
the equipment.
The CE Mark is a Directive
conformity mark of the European
Community. (EC)
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAME AND FUNCTION OF EACH BUTTON
SIGNAL EMISSION INDICATOR
Light red while the laser beam is
emitted from the Laser Light
Window or the signal is being
sent from the remote control unit
to the projector.
POWER ON-OFF button
Turn the projector on or off.
VIDEO button
Select the input source
(VIDEO).
COMPUTER button
Select the input source (COM-
PUTER).
AUTO PC button
Operate the Auto PC adjust-
ment function.
D.ZOOM buttons
Select the Digital zoom +/–
mode and resize the image.
KEYSTONE button
Correct keystone distortion.
POINT (VOLUME+/-)
buttons
SELECT button
Execute the item selected, or
expand or compress the
image in the Digital zoom +/-
mode.
Select an item or adjust the
value in the On-Screen Menu.
These are also used to pan the
image in the Digital zoom +/-
mode. The POINT 7 8 buttons
are also used as the VOLUME
+/- buttons.
MENU button
Open or close the On-Screen
Menu.
LASER button
Operate the Laser pointer
function. The Laser beam is
emitted while pressing this
button within 1 minute. When
using this laser pointer for
more than 1 minute, release
the LASER button and press it
again.
FREEZE button
Freeze the projected picture.
PAGE buttons
Turn page; the Up button to
the previous page and the
Down button to the next page
for an image from a computer.
Connect the projector and
your computer with a USB
cable before use.
IMAGE button
Select image levels.
P-TIMER button
NO SHOW button
Turn the picture into black
image.
Operate the P-Timer func-
tion.
MUTE button
Mute the sound.
Note : For detailed operation, refer to the projector owner's manual.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LASER POINTER FUNCTION
This remote control emits a laser beam from the Laser Light Window. With the LASER button pressed, the laser light goes
on. The signal emission indicator lights red and the laser is emitted with red light. With the LASER button pressed for more
than 1 minute or released, the light goes off.
To lock this function, press both the MENU button and the NO SHOW button for more than 10 seconds. To unlock, press
the MENU button and NO SHOW button again for more than 10 seconds.
The laser emitted is a class II laser. Do not look into the laser light window or shine the laser beam on yourself or other
people. The caution labels for laser beam are shown below.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure. Do not look into the Laser Light Window while the laser is emitted, otherwise
eye damage may result.
The caution label is put on the remote control.
Signal Emission Indicator
Laser Light Window
REMOTE CONTROL BATTERY INSTALLATION
Remove the battery
compartment lid.
Slide the batteries into
the compartment.
Replace the compartment lid.
1
3
2
Two AAA size batteries
Press the lid downward
and slide it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AAA, SUM-4 or LR03 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture, or heat.
● Do not drop the remote control.
● If battery solution has leaked in the battery compartment, carefully wipe the compartment clean and install
new batteries.
● Risk of explosion if the battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
TECHNICAL SPECIFICATIONS
AAA, SUM-4 or LR03 Type x 2
Power Source
Operating Range
Dimensions
16.4’ (5m) / 30˚
1.8” x 1.0” x 5.7” (45mm x 25mm x 145mm)
0.22 lbs (99 g) (including batteries)
Net Weight
Class II Laser (Max. Output : 1m W / Wave length : 640-660nm)
Laser Pointer
Specifications are subject to change without notice.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|