Sanyo Projector PLC SW35 User Guide

Multimedia Projector  
MODEL PLC-SW35  
Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Trademarks  
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective  
corporation.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To the Owner  
Before operating this projector, read this manual thoroughly  
and operate the projector properly.  
Safety Precaution  
This projector provides many convenient features and  
functions. Operating the projector properly enables you to  
manage those features and maintains it in better condition for  
a considerable time.  
Improper operation may result in not only shortening the  
product-life, but also malfunctions, fire hazard, or other  
accidents.  
If your projector seems to operate improperly, read this  
manual again, check operations and cable connections and try  
the solutions in the “Troubleshooting” section in the end of  
this booklet. If the problem still persists, contact the dealer  
where you purchased the projector or the service center.  
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC  
SHOCK, DO NOT EXPOSE THIS APPLIANCE  
TO RAIN OR MOISTURE.  
– This projector produces intense light from the projection  
lens. Do not stare directly into the lens as possible. Eye  
damage could result. Be especially careful that children do  
not stare directly into the beam.  
– Install the projector in a proper position. If not, it may  
result in a fire hazard.  
– Provide appropriate space on the top, sides and rear of the  
projector cabinet for allowing air circulation and cooling the  
projector. Minimum clearance must be maintained. If the  
projector is to be built into a compartment or similarly  
enclosed, the minimum distances must be maintained. Do  
not cover the ventilation slot on the projector. Heat build-  
up can reduce the service life of your projector, and can  
also be dangerous.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
SIDE and TOP  
REAR  
CAUTION : TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER (OR  
BACK). NO USER-SERVICEABLE PARTS  
INSIDE EXCEPT LAMP REPLACEMENT.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
50cm  
1m  
1m  
50cm  
– Do not put any flammable object or spray can near the  
projector, hot air is exhausted from the ventilation holes.  
THIS SYMBOL INDICATES THAT DANGEROUS  
VOLTAGE CONSTITUTING A RISK OF ELECTRIC  
SHOCK IS PRESENT WITHIN THIS UNIT.  
– If the projector is not to be used for an extended time,  
unplug the projector from the power outlet.  
THIS SYMBOL INDICATES THAT THERE ARE  
IMPORTANT OPERATING AND MAINTENANCE  
INSTRUCTIONS IN THE OWNER'S MANUAL WITH  
THIS UNIT.  
READ AND KEEP THIS OWNER'S MANUAL FOR LATER  
USE.  
CAUTION  
Not for use in a computer room as defined in the Standard for  
the Protection of Electronic Computer/Data Processing  
Equipment, ANSI/NFPA 75.  
Ne peut être utilisé dans une salle d’ordinateurs telle que  
définie dans la norme ANSI/NFPA 75 Standard for Protection  
of Electronic Computer/Data Processing Equipment  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety Instructions  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest  
on the power cord. Do not locate this projector where the  
cord may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector,  
ask the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to ensure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn, moet u  
ze niet weggooien maar inleveren  
als KCA.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
NL  
Do not install the projector near the ventilation duct of air-  
conditioning equipment.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Safety Instructions  
Air Circulation  
Installing the Projector in Proper Position  
Openings in the cabinet are provided for ventilation and to  
ensure reliable operation of the product and to protect it from  
overheating, and these openings must not be blocked or  
covered.  
Install the projector properly. Improper Installation may reduce  
the lamp life and cause a fire hazard.  
20˚  
Do not tilt the projector more than 20  
degrees above and below.  
CAUTION  
20˚  
Hot air is exhausted from the exhaust vent. When using or  
installing the projector, the following precautions should be  
taken.  
– Do not put any flammable objects near the vent.  
– Keep the exhaust vent at least 3’(1m) away from any  
objects.  
Do not point the projector up to  
project an image.  
– Do not touch a peripheral part of the exhaust vent,  
especially screws and metallic part. This area will become  
hot while the projector is being used.  
– Do not put anything on the projector. The materials put on  
the cabinet will not only get damaged but also cause fire  
hazard by heat.  
Cooling fans are provided to cool down the projector. This  
projector monitors internal temperature and control the  
running speed of the cooling fans.  
Do not point the projector down to  
project an image.  
Do not put the projector on either  
side to project an image.  
Moving the Projector  
When moving the projector, replace the Lens Cover and  
retract Adjustable Feet to prevent damage to the lens and  
cabinet.  
Air Intake Vent  
When the projector is not in use for an extended period, put  
it into the case (carrying bag) supplied with the projector.  
Exhaust Vent  
(Hot air exhaust)  
CAUTION  
Carrying Bag (supplied) is intended for protection from dust  
and scratches on the surface of a cabinet, and it is not  
designed to protect an appliance from external forces. Do not  
transport a projector through a courier or transport services  
with this bag, otherwise the projector can be damaged. When  
handling a projector, do not drop, bump, subject it to strong  
forces or put other things on the cabinet.  
USE CAUTION IN CARRYING OR  
TRANSPORTING THE PROJECTOR  
– Do not drop or bump a projector, otherwise damages or  
malfunctions may result.  
– When carrying a projector, use a suitable carrying case.  
– Do not transport a projector by using a courier or transport  
service in an unsuitable transport case. This may cause  
damage to a projector. To transport a projector through a  
courier or transport service, consult your dealer for their  
information.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Compliance  
Federal Communication Commission Notice  
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC  
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or  
modifications should be made, you could be required to stop operation of the equipment.  
Model Numbers  
Trade Name  
: PLC-SW35  
: Sanyo  
Responsible party  
Address  
: SANYO FISHER COMPANY  
: 21605 Plummer Street, Chatsworth, California 91311  
Telephone No.  
: (818)998-7322  
AC Power Cord Requirement  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :  
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and  
certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into  
the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the  
outlet, contact your electrician.  
GROUND  
AC Power Cord for the United Kingdom :  
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the  
ASA  
fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus  
. If the fuse cover is  
detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible  
on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.  
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.  
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)  
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET  
OUTLET.  
The Wires in this mains lead are coloured in accordance with the following code:  
Green-and-yellow ············ Earth  
Blue ································· Neutral  
Brown ······························ Live  
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in  
your plug proceed as follows:  
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety  
earth symbol  
or coloured green or green-and-yellow.  
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.  
WARNING : THIS APPARATUS MUST BE EARTHED.  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Part Names and Functions  
qZoom Lever  
Front  
wInfrared Remote Receiver  
eFocus Ring  
rProjection Lens  
tLens Cover  
q
w
yAir Intake Vent  
u Exhaust Vent  
CAUTION  
i
e
r
Hot air is exhausted from the exhaust vent. Do  
not put heat-sensitive objects near this side.  
u
i Speaker  
t
y
oAir Intake Vent  
Back  
!Terminals and Connectors  
!Power Cord Connector  
!Top Controls and Indicators  
!Air Intake Vent  
!
!Exhaust Vent  
o
!
CAUTION  
!
!
Hot air is exhausted from the exhaust vent. Do  
not put heat-sensitive objects near this side.  
!
!Adjustable Feet  
!Air Intake Vents  
!Air Filters  
!
Bottom  
!
!
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Part Names and Functions  
Rear Terminal  
q
w
e
r
SERVICE PORT  
VIDEO  
AUDIO IN  
AUDIO OUT  
(VARIABLE)  
COMPUTER / S-VIDEO  
/COMPONENT IN  
MONITOR OUT  
RESET  
y
t
q
t MONITOR OUT  
VIDEO  
Connect the composite video output from video  
equipment to VIDEO jack. (p16)  
This terminal outputs the signal coming from  
COMPUTER / S-VIDEO / COMPONENT IN terminal.  
(This terminal cannot output RGB(Scart) signal from  
COMPUTER / S-VIDEO / COMPONENT IN terminal.)  
(p15)  
w AUDIO IN (Stereo)  
Connect the audio output from computer or video  
equipment connected to qor yto this jack. (p15, 16)  
y COMPUTER / S-VIDEO / COMPONENT IN  
Connect S-video output, RGB Scart 21-pin video output,  
component video output or computer output to this  
connector. (p15)  
e AUDIO OUT(VARIABLE)  
Connect an external audio amplifier to this jack.  
(p15, 16)  
This terminal outputs sound from AUDIO IN terminal.  
r SERVICE PORT  
This jack is used to service this projector.  
A built-in micro processor which controls this unit may occasionally  
malfunction and need to be reset. This can be done by pressing the RESET  
button with a pen, which will shut down and restart the unit. Do not use the  
RESET function excessively.  
Note:  
• Audio out and Monitor out terminal works only when the projector is under operation and do not work when the projector is in stand-by state or Power  
management mode (p41).  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Part Names and Functions  
Top Control  
i
u
y
WARNING  
LAMP  
POWER  
REPLACE  
q
t
r
INPUT  
ON-OFF  
MENU  
SELECT  
w
e
q POWER ON–OFF button  
y LAMP REPLACE indicator  
Turn the projector on or off. (p17,18)  
Turn yellow when the life of the projection lamp draws  
to an end. (p48)  
w SELECT button  
Execute the item selected. It is also used to expand/  
compress the image in Digital zoom +/– mode. (p31)  
u WARNING indicator  
Light red when the projector detects abnormal condition.  
This also blinks red when the internal temperature of the  
projector exceeds the operating range. (p45)  
e POINT (ed7 8 ) button  
Select an item or adjusts value in the On-Screen Menu.  
These are also used to pan the image in the Digital zoom  
+/– mode. (p31)  
i POWER indicator  
Blink red until the projector gets ready to be turned  
on. It turns red when the projector is in the stand-by  
mode. It remains green while the projector is under  
operation.  
Point 7 8 button are used as VOLUME +/– button. (p23)  
r MENU button  
Open or closes the On-Screen Menu. (p20)  
t
INPUT button  
Select input source. (p24, 32)  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Part Names and Functions  
Remote Control  
qPOWER ON-OFF button  
Turn the projector on or off. (p17, 18)  
wVIDEO button  
Select VIDEO input. (p32)  
eCOMPUTER button  
e
w
q
Select COMPUTER input source. (p24, 32)  
rMENU button  
Open or closes the On-Screen Menu. (p20)  
t
KEYSTONE button  
Correct the keystone distortion. (p22, 38)  
yD.ZOOM ed button  
Select the Digital zoom +/– mode and resize the image.  
(p31)  
-
COMPUTER VIDEO  
ON OFF  
uFREEZE button  
Freeze the picture. (p22)  
iAUTO PC button  
!
Automatically adjust a computer image to its optimum  
setting. (p26)  
r
-
+
MENU VOLUME SELECT VOLUME  
!
!
!
o
!
!
MUTE button  
Mute the sound. (p23)  
t
y
P-TIMER button  
Operate the P-timer function. (p23)  
D.ZOOM KEYSTONE IMAGE NO SHOW  
-
NO SHOW button  
Temporarily turn off the image on the screen. (p22)  
!
FREEZE AUTO PC  
P
TIMER  
! IMAGE button  
MUTE  
Select image level. (p29, 34)  
! SELECT button  
Execute the selected item, or to expand or compress  
the image in Digital Zoom +/– mode. (p31)  
+ / –  
! Point ed 7 8 ( VOLUME  
)
buttons  
Select an item or adjust value in the On-Screen Menu.  
These are also used to pan the image in th Digital  
zoom +/– mode. (p31)  
Point 7 8 buttons are also used as VOLUME +/– mode.  
(p23)  
u
i
o
16.4’  
(5 m)  
Operating Range  
Point the remote control toward the projector (Infrared  
Remote Receiver) whenever pressing any button. Maximum  
operating range for the remote control is about 16.4’ (5m)  
and 60° in front of the projector.  
30°  
30°  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Part Names and Functions  
Remote Control Battery Installation  
Remove the battery  
compartment lid.  
Slide the batteries into  
the compartment.  
Replace the compartment  
lid.  
1
2
3
Two AAA size batteries  
For correct polarity (+ and  
–), be sure battery terminals  
are in contact with pins in  
compartment.  
To insure safe operation, please observe the following precautions :  
Use (2) AAA, SUM-4 or R03 type alkaline batteries.  
Replace two batteries at the same time.  
Do not use a new battery with a used battery.  
Avoid contact with water or liquid.  
Do not expose the remote control to moisture, or heat.  
Do not drop the remote control.  
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.  
Risk of explosion if battery is replaced by an incorrect type.  
Dispose of used batteries according to the instructions.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Positioning the Projector  
This projector is designed to project on a flat projection surface and can be focused from 4.3’(1.3m) - 21.3’(6.5m). Refer to  
the figure and the table below for the screen size and the distance between the projector and the screen.  
A : B = 9 : 1  
21.3' (6.5m)  
16.1' (4.9m)  
(Inch Diagonal)  
200”  
Max. Zoom  
10.6' (3.2m)  
150”  
Min. Zoom  
4.3' (1.3m)  
169”  
100”  
127”  
83”  
40”  
(Center)  
34”  
Screen Size  
(W x H) mm  
4 : 3 aspect ratio  
34”  
40”  
100”  
150”  
200”  
4064 x 3048  
––-––  
691 x 518  
4.3' (1.3m)  
––-––  
813 x 610  
4.9' (1.5m)  
4.3' (1.3m)  
2032 x 1524  
12.5' (3.8m)  
10.6' (3.2m)  
3048 x 2286  
19.0' (5.8m)  
16.1' (4.9m)  
Zoom (min)  
Zoom (max)  
21.3' (6.5m)  
Note:  
• The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.  
• The values shown above are approximate and may vary from the actual size.  
Adjustable Feet  
Projection angle can be adjusted up to 8.0 degrees with the  
adjustable feet.  
Lift the front of the projector and pull upward the feet lock  
latches on both sides of the projector.  
1
Release the feet lock latches to lock the adjustable feet and  
rotate the adjustable feet to adjust the position and tilt.  
2
To retract the adjustable feet, lift the front of the projector  
and pull and undo the feet lock latches.  
Keystone distortion of the projected image can be adjusted  
by Menu operation. (p22, 38)  
3
Feet Lock Latches  
Adjustable Feet  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Connecting the AC Power Cord  
This projector uses nominal input voltages of 100-120 V or 200-240  
V AC. This projector automatically selects the correct input  
voltage. It is designed to work with single-phase power systems  
having a grounded neutral conductor. To reduce risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if you are not sure  
of the type of power being supplied.  
Connect the projector with all peripheral equipment before turning  
the projector on. (See page 15, 16 for connection.)  
CAUTION  
For safety, unplug AC power cord when the projector is not in  
use. When this projector is connected to an outlet with AC  
power cord, it is in Stand-by mode and consumes a little electric  
power.  
Connect AC power cord (supplied) to the  
projector.  
The AC outlet must be near this equipment and  
must be easily accessible.  
NOTE ON THE POWER CORD  
AC power cord must meet requirement of the country where you use a projector.  
Confirm an AC plug type with the chart below and proper AC power cord must be used.  
If supplied AC power cord does not match your AC outlet, contact your sales dealer.  
Projector side  
AC outlet side  
For the U.S.A. and Canada  
For Continental Europe  
For the U.K.  
Ground  
To power cord  
connector on your  
projector.  
To the AC outlet.  
(200 - 240 V AC)  
To the AC outlet.  
(120 V AC)  
To the AC outlet.  
(200 - 240 V AC)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Connecting to a Computer  
Cables used for connection  
• VGA Cable (Mini D-sub 15 pin)  
• Audio Cable (Mini Plug: stereo) ✽  
(= Not supplied with this projector.)  
External Audio Equipment  
Monitor output  
Audio output  
(Stereo)  
Monitor input  
Audio output  
VGA cable  
Audio Cable  
(Stereo) ✽  
VGA cable  
AUDIO IN  
Audio Cable  
(Stereo) ✽  
VIDEO  
AUDIO IN AUDIO OUT  
(VARIABLE)  
SERVICE PORT  
AUDIO OUT  
(VARIABLE)  
COMPUTER / S-VIDEO  
/COMPONENT IN  
MONITOR OUT  
RESET  
MONITOR OUT  
COMPUTER /  
S-VIDEO /  
COMPONENT IN  
Note:  
• When connecting AUDIO OUT to external audio equipment, the projector's built-in  
speaker is disconnected.  
• Audio out and Monitor out terminal works only when the projector is under  
operation and do not work when the projector is in stand-by state or Power  
management mode (p41).  
• See p57 for ordering optional parts.  
Note:  
When connecting the cable, the power cords of both the projector and  
the external equipment should be disconnected from AC outlet.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Connecting to Video Equipment  
Cables used for connection  
• Scart-VGA Cable ✽  
• S-VIDEO-VGA Cable ✽  
• Component-VGA Cable ✽  
• Component Cable ✽  
• Video Cable ✽  
• Audio Cables (Mini Plug: stereo) ✽  
• VGA Cable (Mini D-sub 15 pin)  
(= Not supplied with this projector.)  
External Audio Equipment  
RGB Scart  
21-pin  
Output  
S-Video  
Output  
Component  
Video Output  
(Y, Pb/Cb, Pr/Cr)  
Video  
Output  
Audio  
Output (Stereo)  
Component  
Audio Input  
Video  
cable ✽  
Audio  
cable✽  
cable ✽  
(stereo)  
Scart-VGA  
cable ✽  
S-Video-  
VGA cable✽  
VIDEO  
AUDIO IN  
Component-  
VGA cable ✽  
Audio cable ✽  
(stereo)  
VIDEO  
AUDIO IN AUDIO OUT  
(VARIABLE)  
SERVICE PORT  
AUDIO OUT  
(VARIABLE)  
COMPUTER / S-VIDEO  
/COMPONENT IN  
MONITOR OUT  
RESET  
COMPUTER /  
S-VIDEO /  
COMPONENT IN  
Note:  
• When connecting AUDIO OUT to external audio equipment, the projector's built-in  
speaker is disconnected.  
• Audio out and Monitor out terminal works only when the projector is under  
operation and do not work when the projector is in stand-by state or Power  
management mode (p41).  
• See p57 for ordering optional parts.  
Note:  
When connecting the cable, the power cords of both the projector and  
the external equipment should be disconnected from AC outlet.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
Turning On the Projector  
Complete peripheral connections (with a computer, VCR,  
etc.) before turning on the projector.  
1
2
3
16  
Connect the projector's AC power cord into an AC outlet.  
The POWER indicator blinks red in a moment and lights red.  
Press the POWER ON-OFF button on the top control or on  
the remote control. The POWER indicator turns green  
lighting and the cooling fans start to operate. The  
preparation display appears on the screen and the count  
down starts.  
The preparation display disappears after 20 seconds.  
Selected Input Source and Lamp Mode  
After the count-down, the input source that was selected  
last and the Lamp mode status icon (see page 41) appear on  
the screen.  
4
Lamp mode  
(See page 41 for Lamp mode.)  
If the projector is locked with a PIN code, PIN code Input  
Dialog Box will appear. Enter the PIN code as instructed  
below.  
PIN code Input Dialog Box  
Enter a PIN code  
Pointer  
Select a number by pressing the Point 7 8 button and fix the number with  
the SELECT button. The number will change to "". If you fixed a wrong  
number, move the pointer to "Set" or "Clear" once by pressing the Point d  
button, then return to "PIN code". Enter the correct number again.  
Repeat this step to complete entering a four-digit number.  
When the four-digit number is fixed, the pointer will automatically move to  
"Set". Press the SELECT button so that you can start to operate the  
projector.  
If you entered a wrong PIN code, "PIN code" and the number (✳✳✳✳) will  
turn red and disappear. Enter a correct PIN code all over again.  
After the OK icon  
disappears, you can  
operate the projector.  
What is PIN code?  
PIN code is a security code using Personal Identification Number that  
allows the person who knows it to operate the projector. Setting PIN code  
prevents others except the specific users from operating the projector.  
A PIN code consists of a four-digit number. Refer to PIN Code Lock  
function in Setting on page 43 for locking operation of the projector with  
your PIN code.  
CAUTION ON HANDLING PIN CODE  
If you forget your PIN code, the projector can no  
longer be started. Set a new PIN code with special  
care, write it down in column on page 59 of this  
manual, and keep it at hand. Should the PIN code be  
missing or forgotten, consult your dealer or service  
center.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
Turning Off the Projector  
Press the POWER ON-OFF button on the top control or on  
the remote control, and a message "Power off?" appears on  
the screen.  
1
2
Press the POWER ON-OFF button again to turn off the  
projector. The POWER indicator starts to blink red, and it  
continues while the cooling fans are operating for about 90  
seconds. (About 120 seconds when the fan mode is L2. See  
page 44.)  
The message disappears after 4 seconds.  
When the projector has cooled down enough to be turned on  
again, the POWER indicator lights red. Then you can  
disconnect the AC power cord.  
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN  
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE  
TURNING IT OFF.  
DO NOT DISCONNECT AC POWER CORD WHILE  
COOLING FANS ARE RUNNING OR BEFORE POWER  
INDICATOR LIGHTS RED. OTHERWISE IT WILL  
RESULT IN SHORTENING LAMP LIFE.  
Note:  
• The projector cannot be turned on during the cooling period with the POWER  
indicator blinking red. You can turn it on again after the POWER indicator lights red.  
• When the On start function is on, this projector is turned on automatically by  
connecting the AC power cord to an AC outlet. (See page 41 for the On start  
function.)  
• Do not operate the projector continuously without rest. Continuous use may result  
in shortening the lamp life. Turn off the projector and give it a rest about an hour in  
every 24 hours.  
• This projector monitors internal temperature and automatically controls the  
running speed of the cooling fans.  
• If the WARNING indicator blinks or lights red, see “Warning Indicator” on page 45.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
Zoom and Focus Adjustment  
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to adjust the projected picture focus.  
Zoom Lever  
Focus Ring  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
How to Operate the On-Screen Menu  
Menu icon  
The projector can be adjusted or set via the On-Screen Menu.  
Refer to the following pages regarding each adjustment and  
setting procedure.  
On-Screen Menu  
Menu bar  
Pointer  
(red frame)  
Press the MENU button to display the On-Screen Menu.  
1
Pointer (red frame)  
Press the Point 7 8 buttons to select a Menu icon to adjust.  
Press the Point ed buttons to select an item to adjust.  
Press the Point d button to  
2
move the pointer.  
Press the SELECT button to show the item data. Press the  
Point 7 8 buttons to adjust the data. Refer to the following  
pages for respective adjustment.  
Item  
3
SELECT  
button  
Note:  
• The selected item is not in effective until the SELECT button is pressed.  
Item data  
Press the Point 7 8 buttons  
to adjust value.  
Quit to exit this menu.  
Remote Control  
-
COMPUTER VIDEO  
ON OFF  
POINT button  
MENU button  
-
+
MENU VOLUME SELECT VOLUME  
SELECT button  
Top Control  
POINT button  
(outer ring)  
WARNING  
LAMP  
POWER  
REPLACE  
INPUT  
ON-OFF  
MENU button  
SELECT button  
MENU  
SELECT  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
Menu Bar  
For computer source  
Guide Window  
PC System Menu Image Select Menu  
Used to select Used to select an image  
Screen Menu  
Setting Menu  
Shows the selected  
Menu of the On-  
Screen Menu.  
Used to adjust size  
of image. [Normal  
/ True / Wide /  
Digital zoom +/–]  
(p31)  
Used to change  
settings of the  
projector or reset lamp  
replace counter.  
(p38-44)  
computer system. level among Dynamic,  
(p25)  
Standard, Real,  
Blackboard(Green), and  
Image 1 ~ 4. (p29)  
Input Menu  
PC Adjust Menu  
Image Adjust Menu  
Sound Menu  
Used to select  
input source  
either Computer  
or Video. (p24)  
Used to adjust  
parameters to  
match with input  
signal format.  
(p26-28)  
Used to adjust computer image.  
[Contrast / Brightness / Color  
temp. / White balance (R/G/B) /  
Gamma] (p30)  
Used to adjust  
volume or mute  
sound. (p23)  
For video source  
Input Menu  
Image Select Menu  
Screen Menu  
Used to select  
input source  
either Video or  
Computer.  
(p32)  
Used to select an image  
level among Dynamic,  
Standard, Cinema,  
Blackboard(Green) and  
Image 1 ~ 4. (p34)  
Used to set size  
of image to  
Normal or Wide.  
(p37)  
Same function as  
menu for computer  
source.  
Same function as menu  
for computer source.  
Image Adjust Menu  
AV System Menu  
Used to select  
system of selected  
video source.  
(p33)  
Used to adjust picture image.  
[Contrast / Brightness / Color / Tint  
Color temp. / White balance (R/G/B) /  
Sharpness / Gamma / Progressive /  
Film] (p35-36)  
/
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
Keystone Adjustment  
If a projected picture has keystone distortion, correct image with the keystone adjustment.  
Press KEYSTONE button on the remote control or select  
Keystone on the Setting menu (p38) to display the Keystone  
dialog box.  
1
Correct keystone distortion by pressing Point ed buttons.  
Press Point e button to reduce the upper part of image, and  
press Point d button to reduce the lower part.  
2
Arrows are white in no correction.  
The arrow of direction being corrected turns  
red.  
The arrow disappears at the maximum  
correction.  
If you press the KEYSTONE on the remote  
control once more while the keystone dialog  
box is being displayed, the adjustment will be  
canceled.  
Reduce the upper width with Point e button.  
Reduce the lower width Point d button.  
Picture Freeze Function  
Press the FREEZE button on the remote control to freeze the  
picture on the screen. To cancel FREEZE, press the FREEZE  
button again or press any other button. (p11)  
No Show Function  
Press the NO SHOW button on the remote control to black out the  
image. To restore to normal, press the NO SHOW button again or  
press any other button. When a projected image is captured and  
set as “User” in the Logo item in the Setting Menu (p40), the  
screen changes each time you press the NO SHOW button as  
follows.  
• • • • •  
black out the captured image normal ➜  
The message disappears after 4 seconds.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basic Operation  
P-Timer Function  
Press the P-TIMER button on the remote control. The timer  
display “00 : 00” appears on the screen and the timer starts to  
count time (00 : 00 ~ 59 : 59).  
To stop the P-Timer, press the P-TIMER button. And then, press  
the P-TIMER button again to cancel the P-Timer function.  
Sound Adjustment  
Direct Operation  
indicates approximate  
level of volume.  
Volume  
Press the VOLUME (+/–) button on the top control or on the  
remote control to adjust volume. The volume dialog box appears  
on the screen for a few seconds.  
(+) button to turn up the volume and (–) button to turn down the  
volume.  
Mute  
Press the MUTE button on the remote control to cut off sound.  
To restore sound to its previous level, press the MUTE button  
again or press the VOLUME (+/–) button.  
Press the MUTE button to set  
the Mute function On or Off.  
The display disappears after 4 seconds.  
Menu Operation  
Sound Menu  
Press the MENU button and the On-Screen Menu will  
1
appear. Press the Point 7 8 button to move the red frame  
pointer to the Sound Menu icon.  
Sound Menu icon  
Press the Point d button to move the red frame pointer to  
the item that you want to select, and then press the SELECT  
button.  
2
indicates approximate  
level of volume.  
closes the Sound Menu.  
Volume  
Press the Point 8 button to turn up the volume, and press the  
Point 7 button to turn down the volume.  
Mute  
Press the Point 7 8 button to cut off sound. Dialog box display is  
changed to “On” and sound is cut off. To restore sound to its  
previous level, press the Point 7 8 button again.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Input Source Selection  
INPUT button  
Direct Operation  
Choose Computer by pressing the INPUT button on the top  
control or press the COMPUTER button on the remote control.  
Before using these buttons, correct input source should be  
selected through menu operation as described below.  
WARNING  
POWER  
LAMP  
REPLACE  
INPUT  
button  
INPUT  
ON-OFF  
MENU  
SELECT  
Computer  
Video  
Remote Control  
COMPUTER  
button  
-
COMPUTER VIDEO  
ON OFF  
-
+
MENU VOLUME SELECT VOLUME  
Input Menu icon  
Menu Operation  
Input Menu  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Input Menu icon.  
1
Move the pointer (red  
arrow) to Computer  
and press the SELECT  
button.  
Press the Point d button to move the red arrow pointer to  
Computer and then press the SELECT button.  
2
Computer  
After the Source Select Menu appears for Computer, move  
the pointer to RGB and then press the SELECT button.  
3
Source Select Menu  
Move the pointer to RGB and  
press the SELECT button.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Computer System Selection  
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan  
system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal  
format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is  
shown on page 55 )  
Note:  
The projector may display one of the following messages.  
When the projector cannot recognize connected  
signal conforming to PC Systems provided in this  
projector, Auto PC Adjustment function works to  
display proper images and the message “Auto” is  
displayed on the PC System menu box. When the  
image is not projected properly, manual adjustment is  
required. (p27, 28)  
PC System Menu  
Auto  
The Auto PC Adjustment  
function operates to adjust the  
projector.  
There is no signal input from computer. Check the  
connection of your computer and the projector. (See  
" Troubleshooting" p50)  
-----  
User preset system manually adjusted in PC Adjust  
menu. Adjustment data can be stored in Mode 1 - 5.  
(p27, 28)  
Mode 1  
PC Systems provided in the projector. The projector  
chooses a proper system and displays it.  
SVGA 1  
*Mode 1 and SVGA 1 are examples.  
PC System Menu  
Selecting Computer System Manually  
PC system can also be selected manually.  
The PC System Menu icon  
displays the system being  
selected.  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 buttons to move the red frame  
pointer to the PC System Menu icon.  
1
Systems on this dialog box  
can be selected.  
Press the Point  
d button to move the red arrow pointer to  
2
the system that you want to set, and then press the  
button.  
SELECT  
Custom Mode (1~5) set in the  
PC Adjust Menu. (p27, 28)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Auto PC Adjustment  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to  
your computer. Auto PC Adjustment function can be operated as follows.  
PC Adjust Menu  
Auto PC Adj.  
Press the MENU button to display the On-Screen Menu.  
Press the Point 7 8 button to move the red frame pointer to  
PC Adjust Menu icon.  
1
PC Adjust Menu icon  
Press the Point d button to move the red frame pointer to  
Auto PC Adj. icon and then press the SELECT button twice.  
This Auto PC Adjustment can be also executed by pressing  
2
the Auto PC button on the remote control unit.  
Move the red frame pointer to  
the Auto PC Adj. icon and  
press the SELECT button.  
To store adjustment parameters  
Adjustment parameters from Auto PC Adjustment can be  
memorized in this projector. Once parameters are memorized, the  
setting can be done just by selecting Mode in the PC System  
Menu (p25). See “Store” on page 28.  
Note:  
• Fine sync, Total dots and Picture Position of some computers can not be fully  
adjusted with this Auto PC Adjustment function. When the image is not provided  
properly with this operation, manual adjustments are required. (p 25, 27, 28)  
• The Auto PC Adjust cannot be operated when 480i, 575i, 480p, 575p, 720p,1035i,  
or 1080i is selected in the PC System Menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Manual PC Adjustment  
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC  
Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5  
independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a  
specific computer.  
PC Adjust Menu icon  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the PC Adjust Menu icon.  
PC Adjust Menu  
1
2
Press the Point d button to move the red frame pointer to  
the item that you want to adjust and then press the SELECT  
button. An adjustment dialog box will appear. Press the  
Point 7 8 button to adjust value.  
Move the red frame pointer to  
an item and press the SELECT  
button.  
Fine sync  
Eliminates flicker from the image displayed. Press the Point 7 8  
button to adjust value. (From 0 to 31)  
Shows status  
Total dots  
(Stored / Free) of the  
Selected Mode  
selected Mode.  
Adjusts the number of total dots in one horizontal period. Press  
the Point 7 8 button and adjust number to match your PC image.  
Horizontal  
Adjusts horizontal picture position. Press the Point 7 8 button to  
adjust the position.  
Press the Point 7 8 button to  
adjust the value.  
Vertical  
Adjusts vertical picture position. Press the Point 7 8 button to  
adjust the position.  
Press the SELECT button at  
this icon to adjust the other  
items.  
Current mode  
Press the SELECT button to show H-Freq. and V-Freq. of the  
connected computer.  
Clamp  
Adjusts clamp level. When the image has dark bars, try this  
adjustment.  
Current mode  
Press the SELECT button at  
the Current mode icon to  
show the information of the  
connected computer.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Display area  
Select the resolution at the Display area dialog box.  
Press the SELECT button at  
the Display area icon and the  
Display area dialog box  
appears.  
Display area H  
Adjusts the horizontal area displayed by this projector. Press the  
Point 7 8 button to decrease/increase value and then press the  
SELECT button.  
Display area  
Display area V  
Adjusts the vertical area displayed by this projector. Press the  
Point 7 8 button to decrease/increase value and then press the  
SELECT button.  
Full screen  
With this function on, SXGA image is fully displayed at 4 : 3 aspect  
ratio. It is displayed at 5 : 4 aspect ratio with this function off.  
Reset  
Resets all adjustment to their previous levels.  
To store adjustment data  
This Mode has parameters being stored.  
Mode free  
To clear adjustment data previously set, move the red frame  
pointer to the Mode free icon and then press the SELECT button.  
Move the red arrow pointer to the Mode that you want to clear  
and then press the SELECT button.  
Store  
To store adjustment data, move the red frame pointer to the Store  
icon and then press the SELECT button. Move the red arrow  
pointer to any of Mode 1 to 5 in which you want to store and then  
press the SELECT button.  
Vacant Mode  
shows values of “Total  
dots,” “Horizontal,”  
“Vertical,” “Display area  
H,” and “Display area V.”  
Quit  
Exits the PC Adjust Menu.  
To clear adjustment data  
closes this dialog box.  
Note:  
• Auto PC Adjust, Display area, Display area (H/V), and Full screen cannot be selected  
when “480i”, “575i”, “480p”, “575p”, “720p”, “1035i”, or “1080i” is selected in  
the PC System Menu (p25).  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Input  
Image Level Selection  
Direct Operation  
Remote Control  
-
+
MENU VOLUME SELECT VOLUME  
Select an image level among Dynamic, Standard, Real,  
Blackboard(Green), Image 1, Image 2, Image 3, and Image 4 by  
pressing the IMAGE button on the remote control.  
IMAGE  
button  
Dynamic  
D.ZOOM KEYSTONE IMAGE NO SHOW  
Picture level suitable for viewing picture in a bright room.  
-
FREEZE AUTO PC  
P
TIMER  
MUTE  
Standard  
Normal picture level preset on this projector.  
Real  
IMAGE button  
Dynamic  
Picture level with improved halftone for graphics.  
Blackboard(Green)  
Standard  
Real  
Picture level suitable for the image projected on a blackboard.  
This mode assists to enhance the image projected on a  
blackboard. This is mainly effective on a green colored board, not  
truly effective on a black colored board.  
(Green)  
Blackboard  
Image 1  
Image 2  
Image 3  
Image 1~4  
User preset image in the Image Adjust Menu (p30).  
Menu Operation  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Image Select Menu icon.  
1
Image 4  
Press the Point d button to move the red frame pointer to  
the level that you want to set and then press the SELECT  
button.  
2
Image Select Menu icon  
Image Select Menu  
Dynamic  
Picture level suitable for viewing picture in a bright room.  
Move the red frame pointer to  
the level and press the  
SELECT button.  
Standard  
Normal picture level preset on this projector.  
Real  
Picture level with improved halftone for graphics.  
Blackboard(Green)  
Picture level suitable for the image projected on a blackboard.  
See above for further description.  
The level being selected.  
Image 1~4  
User preset image in the Image Adjust Menu (p30).  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Image Level Adjustment  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Image Adjust Menu icon.  
Image Adjust Menu  
1
2
Image Adjust Menu icon  
Press the Point d button to move the red frame pointer to  
the item that you want to adjust, and then press the SELECT  
button. The level of each item is displayed. Adjust each  
level by pressing the Point 7 8 button.  
Move the red frame pointer to  
the item to be selected and  
then press the SELECT button.  
Contrast  
Press the Point 7 button to decrease contrast and the Point 8  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press the Point 7 button to adjust image darker and the Point  
8
button to adjust image brighter. (From 0 to 63.)  
Selected Image level  
Color temp.  
Press the Point 7 button or the Point 8 button for Color temp.  
level that you want to select. (XLow, Low, Mid, or High)  
White balance (Red)  
Press the Point 7 button to lighten red tone and the Point 8  
button to deepen red tone. (From 0 to 63.)  
Press the Point 7 8 button to  
adjust value.  
White balance (Green)  
Store icon  
Press the SELECT button at  
this icon to store the  
adjustment.  
Press the Point 7 button to lighten green tone and the Point 8  
button to deepen green tone. (From 0 to 63.)  
White balance (Blue)  
Press the Point 7 button to lighten blue tone and the Point 8  
button to deepen blue tone. (From 0 to 63.)  
Gamma  
Press the Point 7 8 button to obtain better balance of contrast.  
(From 0 to 15.)  
Reset  
Resets all adjustment to their previous levels.  
Image Level Menu  
Move the red frame pointer  
to any of Image 1 to 4 where  
you want to set and then  
press the SELECT button.  
Store  
To store the image data adjusted manually, move the red frame  
pointer to the Store icon and press the SELECT button. The  
Image Level Menu will appear. Move the red frame pointer to the  
Image 1 to 4 where you want to set and then press the SELECT  
button.  
Quit  
Closes the Image Adjust Menu.  
Note:  
•After adjusting any of the White balance Red, Green or Blue, the Color temp.  
will change to "User".  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Computer Input  
Screen Size Adjustment  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Screen Menu icon.  
Screen Menu  
1
2
Screen Menu icon  
Press the Point d button and move the red frame pointer to  
the function that you want to select and then press the  
SELECT button.  
Move the red frame to the  
function and press the SELECT  
button.  
Normal  
Provides image to fit screen size.  
True  
Provides image in its original size. When the original image size is  
larger than the screen size (800 x 600), this projector enters  
“Digital zoom +” mode automatically.  
Wide  
Provides image to fit wide video aspect ratio (16 : 9) by expanding  
image width uniformly. This function can be used for providing a  
squeezed video signal at 16 : 9.  
Digital Zoom +  
When the Digital Zoom + is selected, the On-Screen Menu  
disappears and the message “D. Zoom +” is displayed. Press the  
SELECT button to expand the image size. And press the Point  
ed7 8 button to pan the image. The Panning function can work  
only when the image is larger than the screen size.  
A projected image can be also expanded by pressing the D.ZOOM  
button on the remote control.  
Digital Zoom –  
When the Digital Zoom – is selected, the On-Screen Menu  
disappears and the message “D. Zoom –” is displayed. Press the  
SELECT button to compress the image size.  
A projected image can be also compressed by pressing the  
D.ZOOM button on the remote control.  
To exit the Digital Zoom +/– mode, press any button except the  
D.ZOOM ▲▼, SELECT, and Point button.  
To return to the normal screen, press KEYSTONE button or D.  
ZOOM ▲▼ button or select Normal from the Screen menu.  
Note:  
• This Screen Menu cannot be operated when “720p(HDTV)”, “1035i (HDTV)”, or  
“1080i (HDTV)” is selected in the PC System Menu (p25).  
• The True and Digital Zoom +/– cannot be selected when “480i”, “575i”, “480p”,  
or “575p” is selected in the PC System Menu (p25).  
• This projector cannot display any resolution higher than 1280 x 1024. If your  
computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the  
lower before connecting to the projector.  
• The image data in other than SVGA (1280 x 1024) is modified to fit the screen size  
in initial mode.  
• The panning function may not operate properly if the computer system prepared in  
the PC Adjust Menu is used.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video Input  
Input Source Selection  
INPUT button  
Direct Operation  
Choose either VIDEO or COMPUTER by pressing the INPUT  
button on the top control or VIDEO or COMPUTER button on the  
remote control.  
Before using these buttons, correct input source should be  
selected through menu operation as described below.  
WARNING  
POWER  
LAMP  
REPLACE  
INPUT  
button  
INPUT  
ON-OFF  
MENU  
SELECT  
Computer  
Video  
Remote Control  
COMPUTER  
button  
VIDEO  
button  
-
COMPUTER VIDEO  
ON OFF  
-
+
MENU VOLUME SELECT VOLUME  
Input Menu icon  
Input Menu  
Menu Operation  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Input Menu icon.  
1
Move the pointer (red arrow)  
to Computer and press the  
SELECT button.  
Press the Point d button to move the red arrow pointer to  
VIDEO or COMPUTER and then press the SELECT button.  
The Source Select Menu will appear. When you select  
VIDEO, video input is selected. When you select  
COMPUTER, go to step 3 to select input source.  
2
Computer  
Source Select Menu  
Move the pointer to S-Video,  
Component, RGB (Scart) and  
press the SELECT button.  
Move the pointer to the correct input source and then press  
the SELECT button.  
3
When the input source is connected to the  
COMPUTER / S-VIDEO / COMPONENT IN with  
a S-Video-VGA Cable, select S-Video.  
S-Video  
When the input source is coming from video  
Component  
equipment connected to the COMPUTER / S-  
VIDEO / COMPONENT IN with a Component-  
VGA Cable, select Component.  
When the input source is coming from video  
RGB (Scart)  
equipment connected to the COMPUTER / S-  
VIDEO / COMPONENT IN with a Scart-VGA  
Cable, select RGB (Scart).  
Note:  
• S-Video-VGA Cable, Component-VGA Cable and Scart-VGA Cable are optionally  
supplied. See page 57 for order.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video Input  
Video System Selection  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the AV System Menu icon.  
1
Press the Point d button to move the red arrow pointer to  
the system that you want to select and then press the  
SELECT button.  
2
AV System Menu (Video or S-Video)  
Video or S-Video  
Auto  
The projector automatically detects incoming video system, and  
adjusts itself to optimize its performance.  
When Video System is PAL-M or PAL-N, select system manually.  
AV System Menu icon  
This box indicates the system  
being selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If the projector cannot reproduce proper video image, it is  
necessary to select a specific broadcast signal format among PAL,  
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer to a system  
and press the SELECT button.  
AV System Menu (Component)  
Component  
Auto  
The projector automatically detects incoming video signal, and  
adjusts itself to optimize its performance.  
AV System Menu icon  
This box indicates the system  
being selected.  
COMPONENT VIDEO SIGNAL FORMAT  
If the projector cannot reproduce proper video image, it is  
necessary to select a specific component video signal format  
among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i.  
Move the pointer to a system  
and press the SELECT button.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video Input  
Image Level Selection  
Direct Operation  
Remote Control  
Select a desired image level among Dynamic, Standard, Cinema,  
Blackboard (Green), Image 1, Image 2, Image 3, and Image 4 by  
pressing the IMAGE button on the remote control.  
-
+
MENU VOLUME SELECT VOLUME  
Dynamic  
IMAGE  
button  
Picture level suitable for viewing picture in a bright room.  
D.ZOOM KEYSTONE IMAGE NO SHOW  
-
FREEZE AUTO PC  
P
TIMER  
Standard  
Normal picture level preset on this projector.  
MUTE  
Cinema  
Picture level adjusted for the picture with fine tone.  
IMAGE button  
Dynamic  
Blackboard(Green)  
Picture level suitable for the image projected on a blackboard  
This mode assists to enhance the image projected on a  
blackboard. This is mainly effective on a green colored board, not  
truly effective on a black colored board.  
Standard  
Cinema  
Image 1~4  
(Green)  
Blackboard  
Image 1  
Image 2  
Image 3  
User preset image in the Image Adjust Menu (p35, 36).  
Menu Operation  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Image Select Menu icon.  
1
Press the Point d button to move the red frame pointer to  
the level that you want to set and then press the SELECT  
button.  
2
Image 4  
Image Select  
Menu icon  
Dynamic  
Image Select Menu  
Picture level suitable for viewing picture in a bright room.  
Standard  
Move the red frame pointer to a level  
and press the SELECT button.  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for the picture with fine tone.  
Blackboard(Green)  
Picture level suitable for the image projected on a blackboard. See  
above for further description.  
The level being selected.  
Image1~4  
User preset image in the Image Adjust Menu (p35, 36).  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video Input  
Image Level Adjustment  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Image Adjust Menu icon.  
Image Adjust Menu  
1
Press the Point d button to move the red frame pointer to  
the item that you want to adjust and then press the SELECT  
button. The level of each item is displayed. Adjust each  
Image Adjust Menu icon  
2
level by pressing the Point 7 8 button.  
Move the red frame pointer to  
the item to be selected and  
then press the SELECT button.  
Contrast  
Press the Point 7 button to decrease contrast and the Point 8  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press the Point 7 button to adjust image darker and the Point 8  
button to adjust image brighter. (From 0 to 63.)  
Color  
Press the Point 7 button to lighten color and the Point 8 button to  
deepen color. (From 0 to 63.)  
Press the Point 7 8 button to  
adjust value.  
Tint  
Press the Point 7 8 button to obtain proper color. (From 0 to 63.)  
Press the SELECT button at  
this icon to display other items.  
Color temp.  
Press the Point 7 8 button for Color temp. level that you want to  
select. (XLow, Low, Mid, or High)  
White balance (Red)  
Press the SELECT button at  
this icon to display previous  
items.  
Press the Point 7 button to lighten red tone and the Point 8  
button to deepen red tone. (From 0 to 63.)  
White balance (Green)  
Press the Point 7 button to lighten green tone and the Point 8  
button to deepen green tone. (From 0 to 63.)  
White balance (Blue)  
Press the Point 7 button to lighten blue tone and the Point 8  
button to deepen blue tone. (From 0 to 63.)  
Sharpness  
Press the Point 7 button to soften the image and the Point 8  
button to sharpen the image. (From 0 to 15.)  
Gamma  
Press the Point 7 8 button to obtain better balance of contrast.  
(From 0 to 15.)  
Note:  
• The Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M, or  
PAL-N.  
• After adjusting any of the White balance Red, Green or Blue, the Color temp.  
will change to "User".  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Video Input  
Progressive  
Interlaced video signal can be displayed in a progressive picture.  
Off . . . .Not activated.  
L1 . . . . .Select “L1” for an active picture.  
L2 . . . . .Select “L2” for a still picture.  
Image Level Menu  
Move the red frame pointer  
to an image icon to be set  
and then press the SELECT  
button.  
Film  
This function is effective on 3-2 pulldown video sources. With this  
function On, the projector reproduces pictures faithful to the  
original film quality.  
Reset  
Store icon  
Resets all adjustment to their previous figure.  
Store  
To store the adjustment data, move the red frame pointer to the  
Store icon and press the SELECT button. The Image Level Menu  
will appear. Move the red frame pointer to the Image Level 1 to 4  
and then press the SELECT button.  
Quit  
Closes the Image Adjust Menu.  
Note:  
• Progressive cannot be selected when 480p, 575p, 720p, 1035i, or 1080i is  
selected. (p33)  
• Film can only be activated when selecting NTSC and 480i for Video System and  
L1/ L2 for Progressive.  
• 3-2 Pulldown or Telecine transfer is the process of changing images from film mode  
to video mode. While film runs at 24 frames per second (fps), NTSC television  
signals (or video) have a run rate of 30fps so the 24 fps film needs to be speeded  
up to 30fps and transferred using a proper field pattern to get the best film-like  
images.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Input  
Screen Size Adjustment  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press the MENU button and the On-Screen Menu will  
appear. Press the Point 7 8 button to move the red frame  
pointer to the Screen Menu icon.  
Screen Menu  
1
2
Press the Point d button and move the red frame pointer to  
the function that you want to select and then press the  
SELECT button.  
Screen Menu icon  
Move the red frame to a function and  
press the SELECT button.  
Normal  
Provides image at a normal video aspect ratio of 4 : 3.  
Wide  
Provides image at a wide screen ratio of 16 : 9.  
Note:  
• Screen Menu cannot be operated when “720p”, “1035i”, or “1080i” is selected in  
the AV System Menu (p33).  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Setting  
Setting  
This projector has Setting menu that allows you to set up the  
other various functions described as follows;  
Setting Menu (Language)  
Press the MENU button to display the On-Screen Menu.  
Press the Point 7 8 button to move the red frame pointer to  
the Setting Menu icon.  
1
Set the red frame  
pointer to the item  
and press the  
Setting Menu icon  
Press the Point d button to move the red frame pointer to  
SELECT button.  
2
the item that you want to set and then press the  
button. The Setting dialog box appears.  
SELECT  
Language  
The language used in the On-Screen Menu is available in English,  
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Russian, Chinese, Korean, or Japanese.  
When pressing the SELECT  
button at Language, the  
Language Menu appears.  
Keystone  
This function corrects distortion of a projected image. Select  
either Store or Reset with the Point 7 8 button, and then press  
the Select button. The keystone dialog box appears. Adjust  
keystone with the Point ed button.  
Store . . . . stores the keystone adjustment even if the AC  
power cord is disconnected.  
Reset . . . . .resets the keystone adjustment when the AC power  
cord is disconnected.  
Blue back  
When this function is “On,” the projector produces a blue image  
while input signal is not detected.  
Display  
This function decides whether to display On-Screen Displays.  
On . . . . . . . shows all the On-Screen Displays.  
Off . . . . . . . does not show On-Screen Displays except;  
On-Screen Menu  
“Power off?” message  
P-Timer  
“No signal” message  
”Wait a moment!” message  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Setting  
Logo PIN code lock  
Logo PIN code lock  
This function prevents an unauthorized person from changing the  
Logo setting.  
Off . . . . .the Logo setting can be changed freely from the  
Logo menu. (p40)  
On . . . . . .the Logo setting cannot be changed without the  
Logo PIN code.  
If you want to change the Logo PIN code lock setting, enter a  
Logo PIN code along the following steps. The initial Logo PIN code  
is set "4321" at the factory.  
Enter a Logo PIN code  
Select a number by pressing the Point 7 8 button and fix the  
number with the SELECT button. The number will change to "".  
If you fixed a wrong number, move the pointer to "Set" or "Clear"  
once by pressing the Point d button, then return to "Logo PIN  
code". Enter the correct number again.  
Logo PIN code lock Dialog Box  
Repeat this step to complete entering a four-digit number.  
When the four-digit number is fixed, the pointer will automatically  
move to "Set". Press the SELECT button so that you can change  
the Logo PIN code lock setting.  
After a correct Logo PIN code is entered, the  
following dialog box will appear.  
If you entered a wrong Logo PIN code, "Logo PIN code" and the  
number (✳✳✳✳) will turn red and disappear. Enter a correct Logo  
PIN code all over again.  
Pointer  
Change the Logo PIN code  
Logo PIN code can be changed to your desired four-digit number.  
Select "Logo PIN code change" with the Point d button and press  
the SELECT button. Set a new Logo PIN code.  
Select On/Off by pressing the Point 7 8 button or  
change the Logo PIN code.  
Be sure to note the new Logo PIN code and keep it at hand. If  
you lost the number, you could no longer change the Logo PIN  
code setting. For details on PIN code setting, refer to relevant  
instructions of the PIN code lock function on page 43.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
Logo  
This function decides what to be displayed on the starting-up  
display as follows:  
User . . . . . .the image you captured  
Default . . . .the factory-set logo  
Off . . . . . . .count-down only  
Capture  
Capture  
This function enables you to capture the image being projected  
and use it for a starting-up display or interval of presentations.  
After capturing the projected image, go to the Logo function and  
set it to “User”. Then the captured image can be displayed when  
turning on the projector next time or pressing the NO SHOW  
button. (p22)  
Select [Yes] to capture  
the projected image.  
To capture the image, select [Yes]. To cancel the Capture  
function, select [No].  
Note:  
• Before capturing an image, select Standard in the Image Select Menu to capture a  
proper image. (See page 29, 34.)  
• A signal from a computer can be captured up to XGA(1024 x 768). A signal from  
video equipment can be captured except for 720p, 1035i, and 1080i.  
• When capturing the image that has been adjusted by the Keystone function, the  
adjustment data is automatically reset and the projector captures an image without  
keystone adjustment.  
Select [Yes] to  
stop capturing.  
• When the Logo PIN code lock function is On, the Logo and Capture menu cannot  
be selected.  
Ceiling  
Ceiling  
When this function is “On,” the picture is top/bottom and left/right  
reversed. This function is used to project the image from a ceiling  
mounting the projector.  
Rear  
Rear  
When this function is “On,” the picture is left/right reversed. This  
function is used to project the image to a rear projection screen.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
Power management  
Power management  
For reducing power consumption as well as maintaining the lamp  
life, the Power Management function turns off the projection lamp  
when the input signal is interrupted and no button is pressed for a  
certain period.  
Time left until Lamp off  
If the input signal is interrupted and no button is pressed for 30  
seconds or more, the timer display with the message "No signal"  
appears on the screen. The count-down of the set time will get  
started. The count-down time can be set between 1 and 30  
minutes. Set the count-down time with Point 7 8 button.  
When the count-down time has been elapsed, the lamp will be  
turned off to cool itself down. The POWER indicator is blinking red  
during this cooling-off period. The next operation depends on the  
setting as follows :  
Press the SELECT button at  
Power management and this  
box appears. Choose one of  
three settings with the Point 7  
8 button, and go to the timer  
with the Point ed button and  
set time with the Point 7 8  
button.  
Ready . . . . . .When the lamp has been fully cooled down, the  
POWER indicator changes to green blinking. In  
this condition, the projection lamp will be turned  
on if the input signal is reconnected or any  
button on the top control or remote control unit  
is pressed.  
Shutdown . . .When the lamp has been fully cooled down, the  
power will be turned off.  
Off . . . . . . . . .The Power Management function is canceled.  
On start  
When this function is “On,” the projector is automatically turned  
on just by connecting the AC power cord to a wall outlet.  
Note:  
Be sure to turn the projector off properly (see “Turning Off the Projector” on page  
18). If the projector is turned off in the wrong steps, the On start function does not  
operate properly.  
Lamp mode  
This function allows you to change brightness of the screen.  
Normal.........normal brightness  
Auto.............brightness according with the input signal  
Eco  
.......lower brightness reduces the lamp power  
consumption and extends the lamp life.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
Remote control  
Remote control  
This projector has two different remote control codes; the factory-  
set normal code (Code 1) and the secondary code (Code 2). This  
switching function prevents remote control interference when  
operating several projectors or video equipment at the same time.  
When operating the projector in “Code 2”, both the projector and  
remote control must be switched to “Code 2”.  
Press and hold  
MENU and IMAGE  
buttons for 10 seconds  
or more.  
-
+
MENU VOLUME SELECT VOLUME  
To change the code of the projector :  
Set the remote control in the Setting menu to “Code 2.”  
To change the code of the remote control :  
D.ZOOM KEYSTONE IMAGE NO SHOW  
Press and hold both MENU and IMAGE buttons on the remote  
control together for 10 seconds or more. After changing the code,  
make sure the remote control operates properly.  
-
FREEZE AUTO PC  
P TIMER  
To return to the normal code (Code 1), operate both the projector  
and remote control in the ways above again.  
Note :  
When battery of the remote control is replaced, the remote control  
code automatically returns to the normal code (Code 1).  
Key lock  
Key lock  
This function locks operation of the top control and remote control.  
It is useful to prevent operation by an unauthorized person.  
···· not locked.  
···· locks operation of the top control. To unlock, use the  
remote control.  
···· locks operation of the remote control. To unlock, use  
the top control.  
If the top control accidentally becomes locked and you do not have  
the remote control nearby, disconnect the AC power cord from  
the AC outlet, and then with pressing the SELECT button, reinsert  
the AC power cord. This will cancel the top control lock.  
Select Key lock and  
this box appears.  
Choose one of  
these with the  
Point ed button  
and select [Yes] to  
activate it.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
PIN code lock  
PIN code lock  
This function prevents the projector from being operated by an  
unauthorized person and provides the following settings for  
security options.  
...............the projector is unlocked with the PIN code.  
Off  
.............requires to enter the PIN code every time turning on  
the projector.  
On1  
...........requires to enter the PIN code to operate the  
projector once the power cord is disconnected; as  
long as the AC power cord is connected, the  
projector can be operated without the PIN code.  
On2  
When the projector is  
locked with the PIN  
code, the PIN code  
lock mark appears on  
the menu bar.  
Whenever to change the PIN code lock setting or the PIN code  
(the four-digit number), you are required to enter the PIN code.  
"1234" is set as the initial PIN code at the factory.  
Enter a PIN code  
Enter a PIN code  
Select a number by pressing the Point 7 8 button and fix the  
number with the SELECT button. The number will change to  
"". If you fixed a wrong number, move the pointer to "Set" or  
"Clear" once by pressing the Point d button, then return to "PIN  
code". Enter the correct number again.  
Pointer  
Repeat this step to complete entering a four-digit number.  
Quit  
When the four-digit number is fixed, the pointer will  
automatically move to "Set". Press the SELECT button so that  
you can change the following PIN code lock settings.  
The input numbers  
change to “” for  
security.  
If you entered a wrong PIN code, "PIN code" and the number  
(✳✳✳✳) will turn red and disappear. Enter a correct PIN code  
all over again.  
When the pointer  
automatically move  
to "Set", press the  
SELECT button.  
To Change the PIN code lock setting  
Select Off, On1, or On2 with the Point 7 8 button and then  
"Quit" with the Point d button and press the SELECT button to  
close the dialog box.  
Change the PIN code lock setting  
To Change the PIN code  
Select a desired  
The PIN code can be changed to your desired four-digit  
number.  
Select "PIN code change" with the Point d button, and press  
the SELECT button. The New PIN code input dialog box will  
appear.  
setting with the  
Point 7 8 button.  
Select a number with the Point 7 8 button and fix the number  
with the SELECT button. Repeat it to complete entering a four-  
digit number. When the four-digit number is fixed, the pointer  
will automatically move to "Set". Then press the SELECT  
button.  
Change the PIN code  
Select PIN code  
change and press  
the SELECT button.  
The New PIN code  
input dialog box will  
appear.  
CAUTION:  
WHEN YOU HAVE CHANGED PIN CODE, WRITE DOWN THE  
NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO  
ON PAGE 59, AND KEEP IT SECURELY. SHOULD THE PIN  
CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO  
LONGER BE OPERATED.  
The input numbers  
are being displayed  
for confirmation.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
Fan  
Fan  
This function provides you the following alternatives in the cooling  
fans operation after turning off the projector. (p18)  
L1 . . . . . . . .normal operation  
L2 . . . . . .slower operation than the normal (L1), but takes  
longer to cool down the projector. In this mode,  
cooling time after turning off the projector will be  
extended longer than in the normal mode.  
Lamp counter reset  
This function is used to reset the lamp replace counter. When  
replacing the projection lamp, reset the lamp replace counter by  
using this function. See page 49 for operation.  
Factory default  
Factory default  
This function returns all setting values except for the user logo,  
PIN code lock, Logo PIN code lock and the lamp counter to the  
factory default settings.  
Select Factory default and this  
box appears. Select [Yes] , and  
the next box appears.  
Select [Yes] to  
activate it.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance and Cleaning  
Warning Indicator  
The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING  
indicator and the POWER indicator to take proper maintenance.  
The projector is shut down and the WARNING indicator is blinking red.  
TOP CONTROL  
When the temperature inside the projector exceeds the normal  
temperature, the projector is automatically shut down to protect  
the inside of the projector. The POWER indicator is blinking and  
the projector is being cooled down. When the temperature inside  
the projector returns to normal, the POWER indicator lights red  
and the projector can be turned on.  
WARNING  
blinking red  
WARNING  
LAMP  
REPLACE  
POWER  
Note:  
• After the temperature inside the projector returns to normal, the WARNING  
indicator still continues to blink. When the projector is turned on again, the  
WARNING indicator stops blinking.  
-
O
FF  
Then check the matters below:  
– Did you provide appropriate space for the projector to be  
ventilated? Check the installing condition to see if ventilation  
slots are not blocked.  
– Is the projector not installed near the ventilation duct of air-  
conditioning equipment which may be hot? Install the  
projector away from the ventilation duct of air-conditioning  
equipment.  
– Are the air filters clean? Clean the air filters periodically. (p46)  
The projector is shut down and the WARNING indicator lights red.  
TOP CONTROL  
When the projector detects an abnormal condition, it is  
automatically shut down to protect the inside and the WARNING  
indicator lights red. In this case, disconnect the AC power cord  
and reconnect it, and then turn the projector on once again for  
check. If the projector is still turned off and the WARNING  
indicator lights red, disconnect the AC power cord and contact the  
service station for check and repair.  
WARNING  
lights red  
WARNING  
LAMP  
REPLACE  
POWER  
-
O
FF  
CAUTION  
DO NOT LEAVE THE PROJECTOR WITH THE AC  
POWER CORD CONNECTED UNDER THE ABNORMAL  
CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC  
SHOCK.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintenance and Cleaning  
Cleaning the Air Filters  
Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters  
become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat build up and  
adversely affect the life of the projector. Clean the air filters following the steps below.  
Turn off the projector, and disconnect the AC power cord  
from the AC outlet.  
1
Turn the projector upside down and remove the air filters by  
pulling the latches upward.  
2
Clean the air filters with a brush or rinse them softly.  
3
4
When cleaning the air filters by rinsing, dry them well.  
Replace the air filters properly. Make sure that the air filters  
are fully inserted.  
CAUTION  
Do not operate the projector with the air filters removed.  
Air Filter  
Dust may accumulate on the LCD panel and the  
Pull up and remove.  
projection mirror degrading picture quality.  
Do not put small parts into the air intake vents. It may  
result in malfunction of the projector.  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when  
operating the projector. Usage in these environments may  
cause poor image quality.  
When using the projector under dusty or smoky conditions, dust  
may accumulate on a lens, LCD panels, or optical elements inside  
the projector. This condition may degrade the quality of a  
projected image.  
When the symptoms above are noticed, contact your authorized  
dealer or service station for proper cleaning.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintenance and Cleaning  
Cleaning the Projection Lens  
Follow these steps to clean the projection lens.  
Disconnect the AC power cord before cleaning.  
1
Softly wipe the projection lens with a cleaning cloth that  
contains a small amount of non-abrasive camera lens  
cleaner, or use lens cleaning paper or a commercially  
available air blower to clean the lens. Avoid using an  
excessive amount of cleaner. Abrasive cleaners, solvents, or  
other harsh chemicals might scratch the surface.  
2
When the projector is not in use, replace the lens cover.  
3
Cleaning the Projector Cabinet  
Follow these steps to clean the projector cabinet.  
Disconnect the AC power cord before cleaning.  
1
Softly wipe the projector body with a soft, dry cleaning cloth.  
When it is heavily soiled, use a small amount of mild  
detergent and finish with a soft, dry cleaning cloth. Avoid  
using an excessive amount of cleaner. Abrasive cleaners,  
solvents, or other harsh chemicals might scratch the surface.  
2
When the projector is not in use, put the projector in an  
appropriate carrying case to protect it from dust and  
scratches.  
3
Attaching the Lens Cover  
1
2
When moving this projector or while not using it over an extended  
period of time, replace the lens cover.  
Thread the string through the hole on the lens cover and  
then tie a knot in the string to secure it in place.  
1
Thread the other end of the string through the hole at the  
2
bottom of the projector. Then pass the lens cover through  
the resulting loop of the string. Tie a knot in the string to  
secure it in place.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintenance and Cleaning  
Lamp Replacement  
When the life of the projection lamp of this projector draws to an  
end, the LAMP REPLACE indicator lights yellow. If this indicator  
lights yellow, replace the lamp with a new one promptly.  
Top Control  
This indicator lights yellow  
when the life of the projection  
lamp draws to an end.  
WARNING  
LAMP  
REPLACE  
POWER  
CAUTION  
Allow a projector to cool, for at least 45 minutes before  
you open the Lamp cover. The inside of the projector  
can become very hot.  
CAUTION  
For continued safety, replace with a lamp of the same  
type. Do not drop a lamp or touch a glass bulb! The  
glass can shatter and may cause injury.  
Screw  
Lamp Cover  
Follow these steps to replace the lamp.  
Turn off the projector and disconnect the AC plug. Allow the  
projector to cool for at least 45 minutes.  
1
Loosen the screw with a screwdriver, and remove the lamp  
cover.  
2
Loosen 2 screws of the lamp with a screwdriver and pull out  
the lamp by grasping the handle.  
3
Replace the lamp with a new one and tighten the 2 screws  
back into position. Make sure that the lamp is set properly.  
Replace the lamp cover and tighten the screw.  
Screw  
4
Lamp  
Handle  
Connect the AC power cord to the projector and turn on the  
5
projector.  
Reset the Lamp replace counter.  
See “Lamp Replace Counter” on the next page .  
6
Screw  
ORDER REPLACEMENT LAMP  
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following  
information to the dealer.  
Model No. of your projector  
:
:
PLC-SW35  
Replacement Lamp Type No.  
POA-LMP91  
(Service Parts No.610 321 3804 )  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintenance and Cleaning  
Lamp Replace Counter  
Be sure to reset the lamp replace counter after the lamp is replaced. When the lamp replace counter is reset, the LAMP  
REPLACE indicator stops lighting.  
Turn the projector on, press the MENU button and the On-  
Screen Menu will appear. Press the Point 7 8 button to  
move the red frame pointer to the Setting Menu icon.  
1
Press the Point d button to move the red frame pointer to  
the Lamp counter reset item and then press the SELECT  
button. The message "Lamp replace counter reset?" is  
displayed. Move the pointer to [Yes] and then press the  
SELECT button.  
2
Another confirmation dialog box appears and select [Yes] to  
reset the Lamp replace counter.  
3
Move the pointer to Lamp  
counter reset and then press the  
Note:  
SELECT button. The message  
• Do not reset the Lamp replace counter without implementation of lamp  
“Lamp replace counter reset?”  
replacement. Be sure to reset the Lamp replace counter only after replacing the  
is displayed.  
lamp.  
LAMP HANDLING PRECAUTIONS  
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper  
handling may result in accidents, injury, or create a fire hazard.  
Lamp life may differ from lamp to lamp and according to the environment of use. There is no  
guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter  
period of time than other similar lamps.  
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights  
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use  
of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its  
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in  
which the projector and lamp are being used.  
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.  
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an  
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check  
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out  
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one  
should check the inside of the projector except those who are authorized trained technicians and who are  
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those  
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken  
glass.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Troubleshooting  
Before calling your dealer or service center for assistance, check the items below once again.  
– Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to a Computer"  
and “Connecting to Video Equipment” on page15,16.  
– Make sure all equipment is connected to AC outlet and the power is turned on.  
– When you operate the projector with a computer and it does not project an image, restart the computer.  
Problem:  
– Solutions  
No power  
– Plug the power cord of the projector into the AC outlet.  
– See if the POWER indicator lights red.  
– Wait 90-120 seconds after the projector is turned OFF when turning the  
projector back on. The projector can be turned on after the POWER  
indicator turns red. (See “Turning Off the Projector” on page 18.)  
– Check the WARNING indicator. If the WARNING indicator lights red, the  
projector cannot be turned on. (See "Warning Indicator" on page 45.)  
– Check the projection lamp. (See page 48.)  
– Unlock Key lock for the projector in the Setting Menu. (See page 42.)  
Image is out of focus.  
– Adjust focus of the projector. (See page 19.)  
– Provide proper distance between the projector and the projection  
screen. (See page 13.)  
– Check the projection lens to see if it needs cleaning. (See page 47.)  
– Moving the projector from a cool to a warm place may result in moisture  
condensation on the projection lens. In such cases, leave the projector  
OFF and wait until condensation disappears.  
No image  
– Check the connection between your computer or video equipment  
and the projector. (See page 15, 16)  
– See if the input signal is correctly output from your computer. Some  
laptop computers may need to change the setting for monitor output when  
connecting to a projector. See your computer’s instruction manual for the  
setting.  
– It takes about 20 seconds to display an image after turning on the projector.  
– See if the selected system is corresponding with your computer or video  
equipment. (See page 25 and 33)  
– Select correct input source once again through menu operation.  
(See page 24, 32)  
– Make sure the temperature is not out of the specified Operating  
Temperature (5°C ~ 35°C).  
Image is Left/Right reversed.  
Image is Top/Bottom reversed.  
– Check the Ceiling / Rear item. (See “Setting” on page 40.)  
– Check the Ceiling item. (See “Setting” on page 40.)  
No sound  
– Check audio cable connection from audio input source.  
– Adjust the audio source.  
– Press the Volume (+) button. (See page 23.)  
– Press the Mute button. (See page 23.)  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Some displays are not seen  
during the Operation.  
– Check the Display item. (See “Setting” on page 38.)  
PIN code dialog box appears at start-up. – PIN code lock is being set. Input a PIN code (1234 or numbers you have  
set). (See “PIN code lock” on page 17 and 43.)  
The Remote Control does not work.  
– Check the batteries.  
– Make sure no obstruction is between the projector and remote control.  
– Make sure you are not too far from the projector when using the remote  
control. Maximum operating range is 16.4’ (5m).  
– Make sure the code of the remote control is conformed to the projector.  
(See page 42.)  
– Unlock Key lock for the remote control in the Setting Menu. (See page 42.)  
WARNING :  
High voltages are used to operate this projector. Do not attempt to open the cabinet.  
after following all operating instructions,  
Give the model number and explain about the problem. We will advise you how to obtain service.  
If problems still persist  
service center.  
contact the dealer where you purchased the projector or the  
This symbol on the nameplate means the product is  
The CE Mark is a Directive conformity  
mark of the European Community (EC).  
Listed by Underwriters Laboratories Inc. It is designed  
and manufactured to meet rigid U.L. safety standards  
against risk of fire, casualty and electrical hazards.  
Pixelworks ICs used.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Menu Tree  
Computer Input / Video Input  
RGB  
Go to System (1)  
Computer  
Input  
S-Video  
Component  
Go to System (3)  
Go to System (2)  
RGB( Scart )  
N/A  
Go to System (3)  
Video  
N/A - - - not applicable  
Sound  
Sound  
Volume  
Mute  
Quit  
0 - 63  
On / Off  
Computer Input  
MODE 1  
System (1)  
Image Select  
Dynamic  
Standard  
Real  
Blackboard(Green)  
Image 1  
MODE 2  
SVGA 1  
- - - -  
Systems displayed in the System Menu vary  
Image 2  
depending on an input signal.  
Image 3  
Image 4  
PC Adjust  
Auto PC Adj.  
Fine sync.  
Total dots  
Horizontal  
Vertical  
Image Adjust  
Contrast  
Brightness  
Color Temp  
0 - 63  
0 - 63  
High  
Mid  
0 - 31  
Low  
Current mode  
Clamp  
XLow  
Display area  
640 x 480  
720 x 400  
800 x 600  
1024 x 768  
1152 x 864  
1280 x 1024  
1400 x 1050  
Quit  
Red  
Green  
Blue  
Gamma  
Reset  
Store  
0 - 63  
0 - 63  
0 - 63  
0 - 15  
Yes / No  
Image 1  
Image 2  
Image 3  
Image 4  
Quit  
Display area - H  
Display area - V  
Full screen  
Reset  
Quit  
On / Off  
Yes / No  
Mode free  
Store  
Mode 1  
Mode 2  
Mode 3  
Mode 4  
Mode 5  
Quit  
Screen  
Normal  
True  
Wide  
Digital zoom +  
Digital zoom –  
Quit  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Video Input  
Setting  
Setting  
Language  
English  
German  
French  
Italian  
Spanish  
Portuguese  
Dutch  
Swedish  
Russian  
Chinese  
Korean  
Japanese  
Quit  
System (2)  
Auto  
1080i  
1035i  
720p  
575p  
480p  
575i  
480i  
System (3)  
Auto  
PAL  
SECAM  
NTSC  
NTSC 4.43  
PAL-M  
PAL-N  
Keystone  
Blue back  
Display  
Logo PIN code lock  
Store / Reset  
On / Off  
On / Off  
Logo PIN codeentry  
Off  
On  
Image Select  
Dynamic  
Standard  
Cinema  
Blackboard(Green)  
Image 1  
Image 2  
Image 3  
Image 4  
PIN code change  
Quit  
Off  
Default  
User  
Logo  
Capture  
Ceiling  
Rear  
Yes/No  
On / Off  
On / Off  
Power management  
Off  
Ready  
Shut down  
Timer(1-30 Min)  
Quit  
Image Adjust  
Contrast  
Brightness  
Color  
Tint  
Color Temp  
0 - 63  
0 - 63  
0 - 63  
0 - 63  
High  
Mid  
On start  
Lamp mode  
On / Off  
Normal  
Auto  
Eco  
Low  
Remote control  
Key lock  
Code 1  
Code 2  
XLow  
Off  
Red  
Green  
Blue  
Sharpness  
Gamma  
Progressive  
0 - 63  
0 - 63  
0 - 63  
0 - 15  
0 - 15  
Off  
Projector  
Remote Control  
Quit  
PIN code lock  
PIN code lock entry  
Off  
On1  
On2  
PIN code change  
Quit  
L1  
L2  
On/ Off  
Yes / No  
Image 1  
Image 2  
Image 3  
Image 4  
Quit  
Film  
Reset  
Store  
Fan  
L1 / L2  
Lamp counter reset  
Factory default  
Yes / No  
Yes / No  
Quit  
Quit  
Screen  
Normal  
Wide  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Indicators and Projector Condition  
Check the indicators for projector condition.  
Indicators  
Projector Condition  
LAMP  
WARNING  
POWER  
red/green  
REPLACE  
red  
yellow  
The projector is OFF. (The AC power cord is unplugged.)  
The projector is preparing for stand-by or the projection lamp is being  
cooled down. The projector cannot be turned on until cooling is completed.  
The projector is ready to be turned on with the POWER ON-OFF button.  
The projector is operating normally.  
The projector is in the Power management mode.  
The temperature inside the projector is abnormally high. The projector  
cannot be turned on. When the projector is cooled down enough and the  
temperature returns to normal, the POWER indicator lights red and the  
projector can be turned on. (The WARNING indicator keeps blinking.)  
Check and clean the Air filter.  
The projector has been cooled down enough and the temperature returns  
to normal. When turning on the projector, the WARNING indicator stops  
blinking. Check and clean the air filters.  
The projector detects an abnormal condition and cannot be turned on.  
Unplug the AC power cord and plug it again to turn on the projector. If the  
projector is turned off again, disconnect the AC power cord and contact the  
dealer or the service center for service and checkup. Do not leave the  
projector on. It may cause electric shock or a fire hazard.  
• • • blinks red.  
• • • off  
• • • lights green.  
• • • blinks green.  
• • • lights red.  
When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights  
yellow, replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp.  
See page 48 and 49.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Compatible Computer Specifications  
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than  
100 MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
VGA 3  
VGA 4  
VGA 5  
VGA 6  
VGA 7  
MAC LC13  
MAC 13  
480p  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
59.88  
50.00  
XGA 2  
XGA 3  
XGA 4  
XGA 5  
XGA 6  
XGA 7  
XGA 8  
XGA 9  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA 15  
MAC 19  
MAC 21  
SXGA 1  
SXGA 11  
SXGA 13 1280 x 1024  
SXGA 14 1280 x 1024  
SXGA 17  
SXGA 18 1280 x 1024  
720p (HDTV)  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1152 x 900  
68.677  
60.023  
56.476  
60.31  
48.50  
44.00  
63.48  
36.00  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
61.20  
50.00  
50.00  
61.85  
46.43  
45.00  
33.75  
33.75  
28.125  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
87.17  
(Interlace)  
35.00  
640 x 480  
––––––––  
77.07  
75.70  
31.47  
31.25  
15.734  
15.625  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
86.96  
––––––––  
––––––––  
––––––––  
575p  
480i  
575i  
(Interlace)  
60  
58.20  
58.30  
72.00  
75.08  
75.06  
70.40  
65.20  
(Interlace)  
50  
(Interlace)  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
86.00  
(Interlace)  
94.00  
(Interlace)  
1152 x 900  
66.00  
86.70  
(Interlace)  
––––––––  
60.00  
60.00  
––––––––  
1035i (HDTV)  
(Interlace)  
60.00  
(Interlace)  
50.00  
(Interlace)  
––––––––  
1080i (HDTV)  
––––––––  
1080i (HDTV)  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Technical Specifications  
Mechanical Information  
Projector Type  
Multi-media Projector  
Dimensions (W x H x D)  
Net Weight  
10.63" x 3.07" x 7.48" (270mm x 78mm x 190mm) (not including Adjustable Feet)  
4.8lbs (2.2 kg)  
0˚ to 8,0˚  
Feet Adjustment  
Panel Resolution  
LCD Panel System  
Panel Resolution  
Number of Pixels  
0.5" TFT Active Matrix type, 3 panels  
800 x 600 dots  
1,440,000 (800 x 600 x 3 panels)  
Signal Compatibility  
Color System  
PAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i  
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz  
High Definition TV Signal  
Scanning Frequency  
Optical Information  
Projection Image Size (Diagonal)  
Projection Lens  
Adjustable from 34" to 200"  
F 1.6 ~ 1.8 lens with f 18.3 mm ~ 21.9 mm with manual zoom and focus  
Throw Distance  
4.3' ~ 21.2' (1.3m ~ 6.5m)  
160W  
Projection Lamp  
Interface  
Video Input Jack  
Audio Input Jack  
Monitor Out Terminal  
RCA Type x 1  
Mini Jack (Stereo) x 1  
Analog RGB (Mini D-sub 15 pin)  
Computer / S-Video / Component Input Terminal Analog RGB (Mini D-sub 15 pin)  
Service Port Connector  
Audio Output Jack  
Mini DIN 8 pin x 1  
Mini Jack (stereo) x 1 (Variable)  
Audio  
Internal Audio Amp  
Built-in Speaker  
0.8 W RMS  
1 speaker, ø1.3" (32mm)  
Power  
Voltage and Power Consumption  
AC 100 ~ 120 V (3.6 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (1.8 A Max. Ampere), 50 / 60 Hz (Continental Europe and The U.K.)  
Operating Environment  
Operating Temperature  
Storage Temperature  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
14 ˚F ~ 140 ˚F (-10˚C ~ 60 ˚C)  
Remote Control  
Battery  
AAA, SUM-04 or R03 type x 2  
Operating Range  
Dimensions  
16.4’ (5m) / 30˚  
2.0”(W) x 0.91”(H) x 4.8”(D) (51.5mm x 23.2mm x 123mm)  
2.11 oz (60 g) (including batteries)  
Net Weight  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Accessories  
Owner's Manual  
AC Power Cord  
Remote Control and Batteries  
VGA Cable  
Lens Cover with String  
Soft Carrying Bag  
PIN Code Label  
The specifications are subject to change without notice.  
LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of  
the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.  
The On-Screen Menu and figures in this manual may differ slightly from the product.  
Optional Parts  
The parts listed below are optionally available. When ordering those parts, give the item name and Model No. to the sales  
dealer.  
Model No.  
COMPONENT-VGA Cable  
SCART-VGA Cable  
S-Video-VGA Cable  
MAC Adapter  
: POA-CA-COMPVGA  
: POA-CA-SCART  
: POA-CA-VGAS  
: POA-MACAP  
Presentation Kit  
: POA-RCKIT02  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Configurations of Terminals  
COMPUTER INPUT/S-VIDEO INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG)  
Terminal : HDB15-PIN  
1
2
3
4
5
6
7
8
Red (R/Cr) Input / Output  
Green (G/Y) Input / Output  
Blue (B/Cb) Input / Output  
-----  
Ground (Horiz.sync.)  
Ground (Red)  
9
-----  
2
1
5
4
3
10 Ground (Vert.sync.)  
11 Ground / -----  
12  
13 Horiz. sync. Input/Output (Composite H/V sync.)  
14 Vert. sync.  
15  
10  
9
8
7
6
15  
12  
11  
14  
13  
-----  
Ground (Green)  
Ground (Blue)  
-----  
SERVICE PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
Serial  
R X D  
-----  
-----  
GND  
RTS / CTS  
T X D  
GND  
1
8
7
6
5
4
3
2
3
4
5
6
7
8
2
1
GND  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
PIN Code Number Memo  
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the  
number and unable to operate the projector, contact the service station.  
PIN Code Lock No.  
Factory default set No: 1 2 3 4*  
Logo PIN Code Lock No.  
Factory default set No: 4 3 2 1*  
*Should the four-digit number be  
changed, the factory set number will  
be invalid.  
While the projector is locked with the PIN code...  
Put the label below (supplied) on in a prominent place of the  
projector's body while it is locked with a PIN code.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Printed in China  
Part No. 610 321 2166 (1AA6P1P4660A- MR7A-A)  
SANYO Electric Co., Ltd.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Calculator EC 252 User Guide
RCA Flat Panel Television D40W17 User Guide
RedMax Edger HE2601 User Guide
ResMed Oxygen Equipment VPAP ST User Guide
Ricoh All in One Printer 1515 User Guide
Runco Flat Panel Television XP 103DHD User Guide
Samsung Home Theater System HT DS610 User Guide
Sanyo Computer Monitor 42LM5WPTC User Guide
Savin All in One Printer 9915DP User Guide
Seagate Computer Accessories 18FC User Guide