LCD PROJECTOR LENS
MODEL NO. LNS-W02/T02
LNS-W02K/T02K Series
LENS REPLACEMENT AND
INSTALLATION PROCEDURE
NOTES ON LENS INSTALLATION
Lens installation should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to install the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
If you have any questions, contact to the dealers.
PARTS LIST
Following parts are contained in the packing.
· LENS
1 piece
· LENS MOUNTING SCREWS
· DRIVER
6 screws (2 for spare)
1 piece
· LIGHT-BLOCK SHEET
· LENS COVER (UPPER · LOWER )
1 sheet
1 set
Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet assembly after the
lens installation.
1. Confirm the lens is securely fixed by 4 screws.
2. Wiring must not be tangled in the gear of the lens motor or the other
mechanical part.
3. There is no missing part, or no loosing mounting part.
1AA6P1P2289-- (ICSC)
Download from Www.Somanuals.com. All Manuals Search And Download.
❋ Figure shown inside of the cabinet.
LENS MOTOR
(D)
● IN CASE OF MODEL WITH LENS
(D)
REMOVE THE LENS. (See figure-4)
1. Remove the connector “K16B” of the
circuit board.
A
2. Loosen the A, B, C wire holder and
remove the lens motor lead.
(D)
(D)
3. Remove screws D (4 screws) which
fastens the lens and remove the lens.
C
B
LENS MOTOR LEAD
CONNECTOR “ K16B”
Fig-4
LENS MOTOR
(D)
(D)
A
(D)
C
(D)
This part wiring should
not be tightened.
B
INSTALL THE LENS. (See figure-4,5)
3
LENS MOTOR LEAD
CONNECTOR “K16B”
1. Remove protective caps (front
and back ) on the lens.
2. Mount the lens at the lens
mounting bracket with screws
(4 screws) included with the
lens. Use the driver included
with the lens to fasten the
screws . (After using, save it for
latter use.) (See figure-5)
LENS MOUNTING BRACKET
3. Connect the lens motor lead to
the connector “K16B” of the
ATTACHED DRIVER
circuit board. (See figure-4)
4. Fasten the lens motor lead at
the A, B, C points with wire
holder.
(See figure-4)
Fig-5
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHT-BLOCK SHEET
INSTALL THE LIGHT-BLOCK SHEET.
(See figure-6)
4
Install the light-block sheet around the lens
as shown in the illustration.
(Use the sheet included with the lens.)
Fig-6
MOUNT THE LENS COVER. (See figure-7)
5
When in install the both upper and lower lens
covers, put the light-block sheet through the
lens and install the sheet so that it should be
placed in the guide slot of the lens cover. (See
figure-8) If the installation of the light-block
sheet is incorrect, there will be the space
between lens and the lens cover, so that it will
be the cause of leakage of light or the dust
entering at the main cabinet.
UPPER LENS COVER
A
1.Insert the upper part lens cover and fix them
with screws A (4 screws).
A
2.Insert the lower part lens cover and fix them
with screws B (2 screws).
LOWER LENS COVER
Fig-7
B
Set the light-block sheet,
so that the large rounder
side is set over the lens.
❇Removed lens cover in figure-2 is not
used, keep the cover for possible re-
use when current lens is used.
Insert into the slot.
LIGHT-BLOCK SHEET
Fig-8
Download from Www.Somanuals.com. All Manuals Search And Download.
|