HIGH-DEFINITION TELEVISION
Wide Screen LCD Projection TV
MODEL
PLV-55WHD1
PLV-65WHD1
®
™
®
®
“As an ENERGY STAR
Partner, SANYO North
America Corporation has
determined that this
product meets the ENERGY
®
STAR
guidelines for
energy efficiency.”
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to the World of Sanyo
Projection TV properly enables you to manage those features
and maintain it in good condition for many years to come.
Thank you for purchasing this Sanyo LCD Projection
Television. You made an excellent choice for Performance,
Reliability, Features, Value, and Styling.
If your LCD Projection TV seems to operate improperly, read
this manual again, check operations and cable connections and
try the solutions in the “Helpful Hints” section, page 29 of this
manual. If the problem still persists, after following all
operating instructions, contact the dealer where you purchased
the LCD Projection TV or the service center. Specify the model
number (see the back of your LCD Projection TV) and explain
about the problem. We can help!
Important Information
Before installing and operating this LCD Projection TV, read
this manual thoroughly. This LCD Projection TV provides
many convenient features and functions. Operating the LCD
*“PTV” may be used as an abbreviation for LCD Projection TV in this manual.
CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . .2
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . .5
Child Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Clearance Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TV Stand Installation Precautions . . . . . . . . . . . . . . . . . . .5
Product Safety Features . . . . . . . . . . . . . . . . . . . . . . . . .6
Air Circulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Cooling Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . . . .6
Getting Started (Required Initial Setup) . . . . . . . . . . . . . .7
Initial Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Digital (DTV) RF Antenna Connection . . . . . . . . . . . . . . . . .7
Analog RF Antenna Connection . . . . . . . . . . . . . . . . . . . . .7
Install Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connect AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Turn On The LCD Projection TV . . . . . . . . . . . . . . . . . . . . . . .9
All Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Antenna Signal Selection (Optional) . . . . . . . . . . . . . . . . . . .9
Turn Off The LCD Projection TV . . . . . . . . . . . . . . . . . . . . .10
Front, Side, and Back Panels . . . . . . . . . . . . . . . . . . . .11
Choose Your Connection . . . . . . . . . . . . . . . . . . . . . . . .12
Digital AV Connections . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting External Equipment to HDMI
(Includes HDCP Copy Protection) . . . . . . . . . . . . . . . . . . . .13
Connecting STB with DVI Output to HDMI Input . . . . . . . . .14
Connecting Digital Audio Out
to a Multi-Channel Receiver . . . . . . . . . . . . . . . . . . . . . . . . .14
Analog AV Connections . . . . . . . . . . . . . . . . . . . . . . . .15
Using Component Jacks to Connect a DVD Player
or Other Digital Equipment . . . . . . . . . . . . . . . . . . . . . . . . .15
Using the Analog VIDEO1 Jacks to Connect a VCR
(or Other Analog Device) . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting Analog Audio Out Jacks
to a Stereo Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . .18
Remote Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adjustment And Setup . . . . . . . . . . . . . . . . . . . . . . . . .20
Basic Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Menu Navigation Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Menu Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
All Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Digital Cable Search (Optional) . . . . . . . . . . . . . . . . . . . . . .21
Digital Add-On Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Analog Antenna Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Changing the Look of Digital Captions . . . . . . . . . . . . . . .23
To View Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
V-Guide (Parental Control) . . . . . . . . . . . . . . . . . . . . . . . . .24
To Block MPAA or TV Program . . . . . . . . . . . . . . . . . . . .24
To Setup V-Guide Ratings . . . . . . . . . . . . . . . . . . . . . . . .24
To Temporarily Unblock MPAA or TV Program . . . . . . . .25
To Unblock/Block All MPAA or All TV Program . . . . . . . .25
MPAA Movie Ratings (Age-Based) . . . . . . . . . . . . . . . . . .25
TV Ratings (Age/Content-Based) . . . . . . . . . . . . . . . . . . .25
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Lamp Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Lamp Counter Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Helpful Hints (Problems/Solutions) . . . . . . . . . . . . . . . .29
Maintenance And Cleaning . . . . . . . . . . . . . . . . . . . . . .30
Cleaning the LCD Projection TV . . . . . . . . . . . . . . . . . . . . . .30
Warning Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Optional Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
This LCD ProjectionTV is designed with the most advanced technology for various use. The LCD
ProjectionTV has a large screen and uses built-in multimedia features, a palette of 16.77 million
colors, and matrix liquid crystal display (LCD) technology.
◆ PLV-55WHD1: 55”/PLV-65WHD1: 65” Wide
Screen LCD Projection TV
◆ Channel Scan Memory
◆ Receives 181 Analog Channels (VHF 2–13 and
◆ Side bar Controls
UHF 14–69; Cable 14–125); and 99 Digital
Channels
◆ 3-Line Digital Comb Filter
◆ HDMI (High-Definition Multimedia Interface) Input
with HDCP (High-bandwidth Digital Content
Protection)
◆ Built-in Digital and Analog Tuners
◆ Trilingual Menu options (English, Spanish, or
French)
◆ RF Antenna Input Jacks: Digital and Analog
◆ Component Video Input (Two Sets)
◆ Rear Composite AV Input
◆ S-Video Input
◆ V-Chip for Movies and TV guidelines rating limits
◆ Closed-Captioning: Analog EIA 608B/Digital EIA-
708B
◆ Audio Modes: Digital—Main and Sub
◆ Optical Digital Audio Out
◆ Fixed Analog Audio Out
◆ Woofer
Analog—Stereo, Mono, and SAP
◆ Front speakers (two): 5.0” x 3.0”
◆ Factory preset adjustments for picture/sound
◆ Picture Shape: PIX1, PIX2, PIX3, and PIX4
◆ Automatic Channel Search
◆ XDS (Extended Data Services) displays station call
letters, title of show, and ratings when broadcast
◆ Sleep Timer (3 hours)
◆ Audio Format: Dolby® digital for DTV/Analog for
◆ 32-Key Remote Control
NTSC
◆ Receivable Formats: Digital Tuner for ATSC
terrestrial broadcasts and nonscrambled
(ClearQAM) cable channels. NTSC analog tuner for
VHF/UHF or CATV
Trademarks Information:
•Manufactured under license from Dolby Laboratories “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
•WOW, SRS and
symbol are trademarks of SRS Labs, Inc.
•WOW technology is incorporated under license from SRS Labs, Inc.
•HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
•Each name of corporations or products in this owner’s manual is either a trademark or a registered trademark of its
respective corporation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PRECAUTIONS
CHILD SAFETY
Sanyo is committed to making home entertainment
safe and enjoyable. Always use a factory authorized
table or stand when positioning your LCD Projection
TV. Use appropriate brackets, braces, or straps to
anchor your furniture in place. But never screw
anything directly to the LCD Projection TV.
Do not place your LCD Projection TV on dressers,
shelves, desks, carts, etc. where curious or excited
children could pull, push, or otherwise cause the unit
to fall and cause personal injury.
Never place toys or other items on top of the LCD
Projection TV that could pique children’s curiosity
causing them to climb about the furniture.
Always use stands that are designed to support the
size and combined weight of your LCD Projection TV
and other electronic devices.
4"
(10 cm)
CLEARANCE PRECAUTIONS
8"
8"
• Place this LCD Projection TV as indicated here.
Failure to do so may result in a fire hazard. Allowing
the proper amount of space at the top, sides, and rear
of the LCD Projection TV cabinet is critical for proper
air circulation and cooling of the unit. The dimensions
shown here indicate the minimum space required.
If the LCD Projection TV is to be built into a
(20 cm)
(20 cm)
4"
(10 cm)
Place the LCD Projection TV on a flat surface or use
the LCD Projection TV stand. Placing on an uneven
surface may cause picture tilt and distortion. Do not
position the LCD Projection TV in a confined area.
Allow adequate space for proper ventilation.
compartment or similarly enclosed, these minimum
distance must be maintained.
• Do not cover the ventilation slot on the LCD
Projection TV. Heat build-up can reduce the life of
your LCD Projection TV, and can also be dangerous.
• If the LCD Projection TV is not to be used for an
extended period of time, unplug it from the power
outlet.
TV STAND INSTALLATION
PRECAUTIONS
When installing the LCD Projection TV, secure the
Projection TV on the specified stand with the three (3)
screws and three (3) washers (included with the stand).
If not, the LCD Projection TV may fall down and
accident can result.
Screw hole
Stand
Washer
(supplied with the stand)
Screw
(supplied with the stand)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SAFETY FEATURES
AIR CIRCULATION
The openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and protect
it from overheating, these openings must not be
blocked or covered.
Hot air is exhausted from the exhaust vent. When
using or installing the LCD Projection TV, the following
precautions must be taken.
• Do not put any flammable object or spray can near
the LCD Projection TV. Hot air is exhausted from the
ventilation holes.
• Keep the exhaust vent at least 4” (10 cm) away from
any objects.
Exhaust Vents
(Hot air exhaust)
Air Intake Vents
• Do not touch the periphery of the exhaust vent,
especially screws and metallic part. These areas will
become hot while the LCD Projection TV is in use.
COOLING FANS
BE SURE TO USE OR PLACE THE LCD PROJECTION TV
WITHIN THE TEMPERATURE RANGE INDICATED BELOW:
Cooling fans are provided to cool the LCD Projection
TV. The fans’ running speed is changed according to
the temperature inside the LCD Projection TV. When
the LCD Projection TV is cooled down enough, the fans
will stop running.
Operating Temperature
Storage Temperature
41 °F to 95 °F (5 °C to 35 °C)
14 °F to 140 °F (–10°C to 60°C)
HANDLING PRECAUTIONS
• Handle the LCD Projection TV carefully when installing.
Do not drop.
• Locate the set away from heat, excessive dust, and
direct sunlight.
• Do not push or hit the screen surface.
• Do not write, paint, or affix anything on the screen.
• Do not put anything on the LCD Projection TV.
DO NOT PUSH OR
HIT THE SCREEN.
• Throughout the installation process, handling by more
than two people is recommended.
• Never touch the projection screen directly with hands.
Doing so may affect the projection image quality.
For cleaning the LCD Projection TV, refer to “Cleaning
the LCD Projection TV” on page 30.
Note: Black dots or bright points of light (red, green, or blue)
may appear on the screen. This is a characteristic of the LCD
panels, not a malfunction of the LCD Projection TV.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED (Required Initial Setup)
This LCD ProjectionTelevision will reproduce a crystal clear digital picture and exceptional sound.
The signal makes the difference!
DIGITAL ANTENNA INPUT
INITIAL SIGNAL CONNECTIONS
1
DIGITAL
AUDIO
OUTPUT
DIGITAL
Digital (DTV) RF Antenna Connection
ANTENNA IN
• Connect an RF antenna to the “Digital Antenna In”
terminal.
PTV BACK
DIGITAL RF
ANTENNA
The digital tuner in this LCD Projection TV receives HD
signals from an antenna. Digital signals from a set-top
box (STB) are received through the Component In jacks.
This LCD Projection TV can receive ANY resolution
being broadcast (HDTV, EDTV, or SDTV).
Analog RF Antenna Connection
• Connect a Cable signal (with or without a cable box),
Satellite Receiver, or RF antenna to the “UHF/VHF/
CATV” terminal.
The analog tuner in this LCD Projection TV receives
Analog Antenna signals, Analog Cable signals, or the
RF output from a Satellite Receiver, VCR or cable box.
PTV BACK
PTV BACK
PTV BACK
UHF/VHF/CATV
UHF/VHF/CATV
UHF/VHF/CATV
OR
OR
DIGIT
AUDI
OUTP
VCR BACK
VCR BACK
VCR BACK
IN
IN
IN
FROM ANT.
FROM ANT.
FROM ANT.
OUT
OUT TO TV
OUT
OUT
OUT TO TV
OUT TO TV
ANALOG SATELLITE RECEIVER
ANALOG RF
ANTENNA
CATV IN
CH3
CH4
VIDEO
VIDEO
L- AUDIO-R
L- AUDIO-R
IN FROM
SAT.
OUT TO TV
S-VIDEO
ANALOG CABLE
Notes:
CATV FRANCHISE NOTE: Cable companies, like public
utilities, are franchised by local government authorities.
To receive cable programs, even with equipment which
is capable of receiving cable channels, the consumer
must subscribe to the cable company’s service.
If you do not have a VCR, connect signal directly to the 75 ohm
terminal (UHF/VHF/CATV).
Don’t be fooled by the phrase “Available in High-Definition.”
The only resolution available with any of these connections,
regardless of the original content, is standard analog (SDTV).
■ The LCD Projection TV will select the correct Antenna mode
■ If you move the LCD Projection TV to a new location, press
the RESET key twice after connecting the signal and turning
on the LCD Projection TV. See RESET key description on
page 19.
for the type of Analog RF signal connected automatically.
■ Use “Analog Antenna Signal” in the Setup menu (see page
22) to change the Antenna Mode.
(Continued on next page.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL BATTERIES
2
• Install two “AAA” Batteries (not included) so that
the “+” and “–” marks on the batteries match the
“+” and “–” marks inside the remote control.
IMPORTANT: Spent or discharged
batteries must be recycled or disposed
properly in compliance with all applicable
laws. For detailed information, contact
your local County Solid Waste Authority.
To review the remote control function, go to pages
18–19.
Note: Use two “AAA” alkaline batteries.
REMOTE CONTROL
CONNECT AC POWER CORD
3
• Connect the AC Power Cord (supplied) to the LCD
Projection TV and electrical outlet.
This LCD projection TV uses nominal input voltages of
120 V AC. It is designed to work with single-phase
power systems having a grounded neutral conductor.
To reduce the risk of electrical shock, do not plug into
any other type of power system. If you are not sure of
the type of power being supplied, consult your
authorized dealer or Sanyo Fisher customer service.
Connect the LCD Projection TV with all peripheral
equipment before turning it on. (See pages 12–17 for
connection.)
To POWER CORD
CONNECTOR on back of
LCD Projection TV.
CAUTION
For safety, unplug the AC power cord when the LCD
Projection TV is not in use.
While this LCD Projection TV is connected to an outlet
with the AC power cord, it is in Stand-by mode and
consumes a little electric power.
AC Power Cord
THE AC OUTLET MUST BE NEAR THIS EQUIPMENT
AND MUST BE EASILY ACCESSIBLE.
To 120 V AC Outlet.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TURN ONTHE LCD PROJECTIONTV
4
FRONT PANEL
• Press the POWER key on the front panel of the LCD
Projection TV or on the remote control. The cooling
fans start to operate and the POWER indicator flashes
green, and after a few seconds it lights green.
LAMP
REPLACE
POWER
POWER
WARNING
POWER indicator POWER key
ALL CHANNEL SEARCH
5
When the television is powered on for the
first time, it automatically checks for the
presence of an RF signal. The initial screen
will be displayed.
➠
• Press the CHANNEL UP (CH e) key
to automatically search for available
channels: Digital (ATSC) and Analog
(NTSC).
If no analog or digital channels are found after the
second search, All Channel Search will default to off-air
analog channels 2 through 69 and digital channel D3-1.
Select analog channels using the remote control keypad.
See page 18, item number 2.
The All Channel Search contains two processes that are
executed simultaneously for digital and analog channels.
Notes:
Channel information found during the All Channel Search is
stored in two Channel Scan Memory databases (Analog
and Digital). After all channel search is completed, the TV
will tune to the lowest Digital channel or lowest Analog
channel if no digital channels are found.
If the TV does not detect any digital or analog channels, a
message advising the viewer to check the cables and
antenna connections will appear. In this case, you must
press the Channel Up (CH e) key again to repeat the
channel search process. If after two searches the TV still
fails to detect any channels, the TV will tune to analog
channel 3.
SKIPTHE CHANNEL SEARCH PROCESS
Use this feature only if the LCD Projection TV is used
primarily for playing video games, or watching videos, or
if you receive local channels from a satellite receiver or
cable system.
ANTENNA SIGNAL SELECTION
(OPTIONAL)
6
To change the initial analog tuning system setup (from
antenna to cable or cable to antenna), use the on-screen
menu, see “Analog Antenna Signal” on page 22.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TURN OFFTHE LCD PROJECTIONTV
7
FRONT PANEL
• Press the POWER key on the front panel of the LCD
Projection TV or on the remote control.
The POWER indicator becomes orange and it
continues while the cooling fans are running (for about
four minutes). The LCD Projection TV can be turned
on again during this period or after the indicator is
turned off.
LAMP
REPLACE
POWER
POWER
WARNING
POWER indicator POWER key
REMOTE CONTROL
• When the LCD Projection TV has cooled down
enough, the POWER indicator will be turned off. Then
you can unplug the AC power cord.
INPUT
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN YOUR LCD PROJECTION TV ON,
WAIT AT LEAST FIVE MINUTES BEFORE
TURNING IT OFF.
POWER
1
4
2
5
3
6
POWER key
DO NOT UNPLUG THE AC POWER CORD
WHILE THE COOLING FANS ARE RUNNING
OR BEFORE THE POWER INDICATOR
BECOMES RED. OTHERWISE IT WILL RESULT
IN SHORTENING OF THE LAMP LIFE.
Notes:
When the lamp did not turn on properly, the LCD Projection
TV will automatically start operating the cooling fans. In this
period, the POWER indicator will flash red and cannot be
turned on.
Do not use the LCD Projection TV continuously without rest.
Continuous use may result in shortening the lamp life.Turn
off the LCD Projection TV and rest it for about an hour in
every 24 hours.
This LCD Projection TV monitors internal temperature and
automatically controls the rotating speed of the cooling fans.
If the WARNING indicator flashes red or becomes red, see
“Warning Indicator” on page 30.
Operational Tip for Monitor Use:
After the initial channel search is completed, you must
press the Channel (CH) ▲ key again to complete the
channel search process. This may take several minutes.
If the LCD Projection TV is used as a monitor only, with
a DVD player or some other type of external equipment,
and no cable or antenna signal is available, the following
setup is necessary:
After the channel search process is complete (2
searches), you can press the INPUT key on the remote
control to use the LCD Projection TV as a monitor.
Your LCD Projection TV is designed to automatically
search for available channels. Therefore, the initial start
up requires that you press the Channel (CH) ▲ key,
enabling the LCD Projection TV to automatically go
through the channel search process before you can
operate the LCD Projection TV.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT, SIDE, AND BACK PANELS
FRONT PANEL
RIGHT SIDE PANEL
(See items 1, 8, & 17
on pages 18 & 19.)
LAMP
POWER
POWER
q
WARNING
REPLACE
INPUT key
w
e
r
t
INPUT
VOLUME + – keys
CHANNEL + – keys
+
VOLUME
y
–
+
BACK PANEL
CHANNEL
–
R-AUDIO-L(MONO)
R-AUDIO-L(MONO)
Y–––––Pb–––––Pr
VIDEO
3
UHF/VHF/CATV
u
i
o
!
Y–––––Pb–––––Pr
R-AUDIO-L(MONO)
R-AUDIO-L(MONO)
AUDIO
OUTPUT
VIDEO
2
!
!
!
S-VIDEO
SERVICE
VIDEO
WOOFER
VIDEO
DIGITAL
DIGITAL
ANTENNA IN
1
AUDIO
HDMI
OUTPUT
!
!
!
POWER indicator— A green light indicates the LCD
Projection TV is on; red light indicates the AC power
cord is connected, but the LCD Projection TV is in the
off condition.
DIGITAL ANTENNA IN—Connect an RF antenna to
this jack.
q
o
!
!
!
SERVICE Jack—This jack is used to service the LCD
Projection TV.
POWER key—Turn the LCD Projection TV on or off.
w
e
Analog AUDIO OUTPUT (L/R)—Connect external
audio equipment here.
Infrared Remote Receiver—Receives the signal from
the remote control.
WOOFER—Connect external audio amplifier to this
jack. This jack outputs woofer sound from TV and the
audio input terminals.
LAMP REPLACE indicator—A yellow light indicates
the lamp has reached the end- of-life. The lamp needs
to be replaced.
r
t
S-VIDEO Input (VIDEO1)—To enhance video detail,
use the S-Video jacks instead of the Video jacks, if
available on your external equipment. (S-Video
connection will override connection to the VIDEO
input jack [VIDEO1]).
!
!
WARNING indicator—A red light indicates the LCD
Projection TV detects an abnormal condition. A
flashing red light indicates that the internal
temperature of LCD Projection TV exceeds the normal
operating range.
AUDIO/VIDEO Input (VIDEO1)—Connect analog
Analog Antenna Input (UHF/VHF/CATV)—Connect
an RF antenna or Analog cable system to this jack.
video equipment here.
Note: S-Video connection overrides the (VIDEO1)
composite video connection.
y
u
HDMI (High Definition Multimedia Interface)
Input—Connect digital video equipment to this jack. It
takes only one high bandwidth cable (not supplied) to
communicate between audio/video equipment and
this LCD Projection TV. This connection is compatible
with DVI equipped devices. (Separate audio
connection and an adapter are required for a DVI
device.)
Component Video Input (VIDEO2)—Connect digital
video equipment to the Y, Pb, Pr, and Audio L/R jacks.
These jacks will automatically detect the type of
signal being received.
!
!
Component Video Input (VIDEO3)—Connect digital
video equipment to the Y, Pb, Pr, and Audio L/R jacks.
These jacks will automatically detect the type of
signal being received.
DIGITAL AUDIO OUTPUT—Use an Optical Audio
cable to connect Digital Audio Output to an advanced
stereo home theater system equipped with Dolby®
Digital 5.1.
i
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSEYOUR CONNECTION
This LCD ProjectionTV is designed to handle
several different connections making it
compatible with Digital and Analog devices.
In order to receive the best performance from
your LCD ProjectionTV, choose your connection
using this chart; then go to the specified page
for detailed instructions.
Digital Signal
Connections
Compatible External
Equipment
Cables Needed
(Not Supplied)
Go to
Page
HDMI
Digital Set-Top Box
or DVD Player
VIDEO GAME
19 PIN HDMI
13
Will accept HDTV
(High Bandwidth
Video component
and Audio 5.1)
OR
14
14
DIGITAL AUDIO OUT
OPTICAL
DIGITAL
CABLE
(Only available when
received as part of a
Digital RF signal or
HDMI signal.)
MULTI-CHANNEL
RECEIVER
Analog Signal
Connections
Compatible External
Equipment
Cables Needed
(Not Supplied)
Go to
Page
COMPONENT
(Y, Pb, Pr) IN
COMPONEN
T VIDEO
CABLE
[Green, Blue,
and, Red
connectors]
15
Will accept HDTV,
EDTV, or SDTV Video
content.
VIDEO GAME
Digital Set-Top
Box or DVD Player
(Requires separate
audio connections.)
AUDIO CABLE
[White and Red
connectors]
COMPOSITE VIDEO
OR
16
COMPOSITE
VIDEO
CABLE
VIDEO GAME
S-VIDEO
DVD PLAYER
[Yellow, White,
and Red connectors]
LEFT/RIGHT
ANALOG AUDIO IN
S-VIDEO CABLE
VCR
ANALOG AUDIO
OUT JACKS
AUDIO CABLE
[White and Red
connectors]
17
STEREO AMPLIFIER
SYSTEM
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL AV CONNECTIONS
This is the best option for picture and sound! Using the HDMI connection, which has high-
definition content protection, provides you with uncompressed digital video and audio, Dolby®
Digital 5.1 or PCM sound. This connection requires only one cable. As Real As It Gets!
To avoid problems with some brands of external
equipment, follow this procedure when connecting
cables and powering on your equipment.
CONNECTING EXTERNAL EQUIPMENTTO HDMI
(INCLUDES HDCP COPY PROTECTION)
Switch off the LCD Projection TV and external equipment
before connecting cable. (Cable is not supplied.)
The LCD Projection TV must be turned on first,
press POWER. Then turn on your external
equipment.
2
3
Connect the external equipment’s high bandwidth
HDMI Output to the LCD Projection TV’s HDMI
Input.
1
Press INPUT to select HDMI to
view a digital program.
SET-TOP BOX (Can be a Digital Satellite Receiver,
DVD PLAYER, or similar digital device.)
REMOTE CONTROL
INPUT
POWER
1
4
2
5
3
6
HDMI Cable
(Gently insert
cable into
PTV’s HDMI
Input jack.)
3
T
DIGIT
AUDI
HDMI
OUTP
P
2
1
PTV BACK
What you will need for connections:
19 Pin HDMI Digital Cable – 1
(Make sure you check the pin
configuration of the cable plug-end*)
*Adapter may be required. Check with
your local electronics store.
IMPORTANT NOTE FOR MONITOR USE:
■ If the television HDMI pin configuration is different from
the pin configuration on your set-top box, you will need to
use an Adapter.
If you did not connect an antenna, you must
run All Channel Search twice before you can
select the AV inputs.
■ Press the INPUT key after connecting cables to access the
AV Inputs. There is NO need to tune to a blank channel.
■ “No Signal” will appear on the screen when no signal is
detected.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING STBWITH DVI OUTPUT
TO HDMI INPUT
CONNECTING DIGITAL AUDIO OUT
TO A MULTI-CHANNEL RECEIVER
Switch off the LCD Projection TV and external
equipment before connecting cable. (Cable is not
supplied.)
Dolby® Digital Audio provides 5.1 channels of surround
sound (five full-range channels [5] and one low-
frequency effect channel [.1]). A fiber optics cable is
used to carry the 5.1 surround sound (for low-noise
signal transfer).
Connect the STB’s DVI Output to a “DVI to HDMI
Cable;” then connect the cable to the LCD
Projection TV’s HDMI input.
1
Using a Fiber Optics cable, connect the LCD
Projection TV’s Digital Audio Output to the Digital
Audio Input of a Multi-Channel Receiver. (Fiber
1
Note: Check with your local electronics store for a
DVI to HDMI Cable that matches your equipment and
the LCD Projection TV.
optics cable is not supplied.)
Connect the STB’s Audio L/R to the LCD
Projection TV’s VIDEO3 Audio L/R.
Press POWER to turn on the LCD Projection TV,
then turn on external equipment.
2
2
Notes:
The LCD Projection TV must be turned on first,
press POWER. Then turn on your external
equipment.
3
When making the connection, do not pinch or kink
the fiber optics cable.
Red light visible at the Digital Audio Output does not
necessarily indicate that Dolby® Digital 5.1 audio is
available. Digital audio is made up of light pulses that
the human eye cannot detect. Dolby® Digital 5.1
audio is available at the Digital Audio Output only
when received as part of a Digital signal.
Press INPUT to select HDMI to view a digital
program.
4
SET-TOP BOX (Can be a Digital Satellite Receiver,
DVD PLAYER, or similar digital device.)
2
AUDIO
CABLE
MULTI-CHANNEL
RECEIVER
1
DIGITAL CABLE
OPTICAL
1
DVI TO HDMI
CABLE
PTV BACK
Y–––––Pb–––––Pr
R-AUDIO-L(MONO)
VIDEO
3
R-AUDIO-L(MONO)
R-AUDIO-L(MONO)
Y–––––Pb–––––Pr
VIDEO
2
DIGI
AUD
OUT
HDMI
REMOTE CONTROL
S-VIDEO
VIDEO
INPUT
POWER
REMOTE CONTROL
1
4
2
5
3
6
PTV BACK
INPUT
POWER
1
4
2
5
3
6
What you will need for connections:
OPTICAL Cable – 1
2
What you will need for connections:
4
DVI to HDMI Cable – 1
Audio Cable – 1
3
IMPORTANT NOTE FOR MONITOR USE:
If you did not connect an antenna, you must run All
Channel Search twice before you can select the AV inputs.
IMPORTANT NOTE FOR MONITOR USE:
If you did not connect an antenna, you must run All
Channel Search twice before you can select the AV inputs.
■ Press the INPUT key after connecting cables to access the
■ Because the VIDEO3 audio jacks are used to receive the
audio from the DVI device, these video jacks cannot be
used when a DVI device is connected.
AV Inputs. There is NO need to tune to a blank channel.
■ With a DVI connection, make sure you connect Audio out to
the LCD Projection TV’s VIDEO3 Audio in.
■ “No Signal” will appear on the screen when no signal is
detected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ANALOG AV CONNECTIONS
USING COMPONENT JACKSTO CONNECT A DVD PLAYER
OR OTHER DIGITAL EQUIPMENT
The Component Video jacks will accept HDTV, EDTV, or
SDTV video content.
Connect DVD Player or similar digital equipment’s
Audio Out to the LCD Projection TV’s VIDEO2 or
VIDEO3 Audio jacks.
2
Switch off the LCD Projection TV and external equipment
before connecting cable. (Cable is not supplied.) Follow
these steps to easily connect your STB or DVD Player to
this LCD Projection TV.
Press POWER to turn on the LCD Projection TV,
then turn on external equipment.
3
4
Press INPUT to select Video 2 or Video 3 to view
the DVD program.
Connect DVD Player or similar digital equipment’s
1
Component Video Out to the LCD Projection TV’s
Video (VIDEO2 or VIDEO3) jacks.
DVD PLAYER
(or similar digital device such
as a Satellite Receiver.)
1
REMOTE CONTROL
INPUT
POWER
1
4
2
5
3
6
2
4
3
2
1
COMPONENT
VIDEO CABLE
AUDIO
CABLE
What you will need for connections:
R-AUDIO-L(MONO)
R-AUDIO-L(MONO)
Y–––––Pb–––––Pr
VIDEO
3
Component Video Cable – 1
Audio Cable – 1
Y–––––Pb–––––Pr
R-AUDIO-L(MONO)
R-AUDIO-L(MONO)
AUDIO
OUTPUT
VIDEO
2
S-VIDEO
IMPORTANT NOTE FOR MONITOR USE:
VIDEO
WOOFER
VIDEO
1
If you did not connect an antenna, you must
run All Channel Search twice before you can
select the AV inputs.
PTV BACK
■ VIDEO2 and VIDEO3 jacks have identical functions.
Compatible video devices can be connected to either set of
jacks.
■ “No Signal” will appear on the screen when no signal is
detected.
■ Press the INPUT key after connecting the cables, to select
the Video 2 or Video 3 input signal. There is NO need to
tune to a blank channel.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
USINGTHE ANALOGVIDEO1 JACKSTO CONNECT AVCR
(OR OTHER ANALOG DEVICE)
Switch off the LCD Projection TV and external equipment
before connecting cable. (Cable is not supplied.)
Optional:
2
Connect VCR’s S-Video Out to the LCD Projection
TV's S-VIDEO In Jack.
Connect VCR’s Audio Video Out to the LCD
Projection TV’s VIDEO1 jacks.
1
Note: S-Video jack connections override VIDEO1 Video
jack connection.
Note: For Mono VCR (Single Audio Jack), connect VCR
Audio Out to LCD Projection TV’s AUDIO-L (MONO)
Input.
Press POWER to turn on the LCD Projection TV,
then turn on external equipment.
3
4
Press INPUT to select Video 1 to
view the VCR program.
PTV BACK
R-AUDIO-L(MONO)
Y–––––Pb–––––Pr
VIDEO
2
REMOTE CONTROL
S-VIDEO
R-AUDIO-L(MONO)
VIDEO
VIDEO
1
INPUT
POWER
1
4
2
5
3
6
S-VIDEO
CABLE
4
3
2
AUDIO
VIDEO
CABLE
1
VCR BACK
What you will need for connections:
Audio Video Cable – 1
S-Video Cable – 1
IMPORTANT NOTE FOR MONITOR USE:
Note: Don’t be fooled by the phrase “Available in High-
Definition.” Composite jacks offer only 480i (SDTV)
resolution. To view available High-Definition (HD) programs,
you must connect your HD equipment to the Component or
HDMI jacks.
If you did not connect an antenna, you must
run All Channel Search twice before you can
select the AV inputs.
■ Press the INPUT key after connecting cables to access
the VIDEO1 input. There is NO need to tune to a blank
channel.
■ “No Signal” will appear on the screen when no signal is
detected.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING ANALOG AUDIO OUT JACKS
TO A STEREO AMPLIFIER
Switch off the LCD Projection TV and external equipment
before connecting cable. (Cable is not supplied.)
Optional:
2
Connect WOOFER jack to the Woofer Amplifier
Input.
Connect the LCD Projection TV’s AUDIO OUT (R/L)
to the Stereo Amplifier In (R/L).
1
Press POWER to turn on the LCD Projection TV,
then turn on external equipment.
3
Note: For Mono Audio Amplifier (Single Audio Jack),
connect to AUDIO-L (MONO) Input.
REMOTE CONTROL
1
AUDIO
INPUT
CABLE
POWER
PTV BACK
1
4
2
5
3
6
R-AUDIO-L(MONO)
R-A
Y–––––Pb–––––Pr
VIDEO
3
3
Y–––––Pb–––––Pr
R-A
R-A
AUDIO
OUTPUT
VIDEO
2
S-VIDEO
VIDEO
WOOFER
VIDEO
1
What you will need for connections:
Audio Cable – 1
2
AUDIO CABLE
(RCA X 1)
Audio Cable (RCA x 1) – 1
STEREO AMPLIFIER
WOOFER AMPLIFIER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USINGTHE REMOTE CONTROL
PRECAUTIONS
Risk of explosion, if battery is replaced by an
incorrect type.
To ensure safe operation, please observe the
following precautions:
If batteries have leaked in the remote control,
carefully wipe the case clean and load new
batteries.
Use two (2) AAA alkaline batteries, see page 8.
Replace both batteries at the same time. Do not
use a new battery with a used battery.
Do not expose the remote control to moisture
or heat.
REMOTE CONTROL KEYS
INPUT Key—Press to change the input signal source
as follows: Analog RF ➡ Digital RF ➡ Video1 ➡
Video2 ➡ Video3 ➡ HDMI ➡ Analog RF.
q
Point toward
LCD Projection TV
NUMBER Keys—Two keys must be pressed to
select a direct channel. Example: Press 0 then 6 to
select channel 6.
w
For Analog Cable channels above 100, press and
hold the 1 key until C1- - appears, then press the
other two numbers.
q
w
!
INFO Key—Press to display the Digital and Analog
Full Banner information (press again to remove the
display).
e
Digital Full Banner display—Contains a two-part
Channel Number (Major and Minor), and Tuner ID. If
available, the following is also included: Station ID, V-
Chip Program Rating, Program Title, Audio Info, and
Signal Strength.
e
r
t
!
!
Channel
!
Tuner ID
Station ID Program Rating
Major
Minor
!
y
Program Title
Audio Info
Signal Strength
u
i
!
!
Analog Full Banner display—Contains the Channel
Number (analog antenna/cable), Tuner ID, Station ID
(if available), Program Title (if available), V-Chip
Program Rating, and Audio Info.
o
!
!
Tuner ID
Channel No.
Station ID Program Rating
Audio Info
Program Title
18
Download from Www.Somanuals.com. All Manuals Search And Download.
RECALL Key—Select the first channel you want to
watch; then select another channel using the
NUMBER keys. Press RECALL to switch easily
between the channels.
Note: The RECALL key is inactive when an external input
is selected (Video 1, Video 2, Video 3, or HDMI) and it
cannot toggle between a Digital channel and an Analog
channel. See TUNER key description.
SLEEP Key—Press this key, then press the “0” key to
set the Sleep Timer. The desired time can be set from
30 minutes up to 3 hours in 30 minutes increments.
To display the remaining time, press this key again.
Sleep Timer will switch off the LCD Projection TV
automatically.
r
!
Note: The Sleep Timer cancels when the LCD Projection
TV is turned off or if a power failure occurs.
MENU Key—Press this key to display the on-screen
menu.
t
y
MUTE Key—Press once to minimize the volume.
!
Press again to restore.
Note: This key will not mute the sound from the audio
out jacks.
TUNER Key—Use this key to toggle from one tuning
system to another, Digital channels and Analog
channels.
Note: The TUNER key is inactive when an external input
is selected (Video 1, Video 2, Video 3, or HDMI).
ENTER Key—Press this key to select an option from
the menu system, when required.
!
!
Cursor e (up) d (down) Keys—Press these keys to
move the cursor up and down within the menu.
Cursor < (left) > (right) Keys—Press these keys to
move the cursor left and right within the menu.
CAPTION Key—Press to select analog or digital
captioning. The Analog Caption modes are: CC1–CC4,
Quikcap, and OFF. The Digital Caption modes are:
Digital CC1–CC6, Quikcap, and OFF.
u
i
EXIT Key—Press this key to exit from the menu
system.
!
!
Channel Scanning (CH ed) Keys—Press e (up) d
(down) keys to tune to the next higher or lower
channel in the Channel Scan Memory list. The
scanning loop includes analog channels, and digital
channels.
Volume (VOL – +) Keys—Press the – + keys to adjust
volume. The screen displays a left or right red arrow
that blinks as many times as you press the VOL – +
keys.
PIX SHAPE Key—Use this key to change the video
display format. Available options depend on signal
received and the broadcast’s aspect ratio. They may
include: PIX1, PIX2, PIX3, and PIX4. See simulated TV
images below:
o
RESET Key—Press twice to restore factory settings.
The LCD Projection TV will automatically start Channel
Search and clear all customized settings (except for
the lamp counter).
Note: The Reset Function includes a channel search.
Current Digital and Analog channel databases will be
deleted and new ones created by the Channel Search
process. To receive Digital Cable channels, see page 21
for Digital Cable Search.
!
These features will reset to the factory defaults:
• Picture Adjustments: Color, Tint, Contrast,
Brightness, Sharpness, and AI
• Sound Adjustments: Treble, Bass, SRS Surround,
FOCUS, TruBass or Woofer Level, and Woofer
• Channel Memory—Digital/Analog channel databases
will be replaced
PIX1
PIX2
Gray colored borders
appear at the sides, of
the screen.
Note: 4:3 image without
distortion on a 16:9 screen.
A 16:9 image fills the
screen normally. A 4:3
image is stretched
horizontally and may
appear distorted.
• Analog Audio to Stereo
• Captioning to OFF
• V-Guide to OFF
• Menu Language to English
• Sleep Timer to OFF (if previously set)
• Any Video mode to TV mode
PIX3
PIX4
• Lamp mode to “Mid” mode
Enlarges a PIX2 image
vertically (some of the
image may be cropped
off).
Stretches the PIX3 image
horizontally (portions of
the sides and/or top and
bottom may be cropped
off).
If desired, personal settings can be made again using
the menu options.
AUDIO Key—Press to select the desired audio mode
(if available): DIGITAL: Main, Sub1, Sub2, Sub3, etc.;
ANALOG: Stereo, Mono, SAP.
!
!
POWER Key—Press to turn the LCD Projection TV on
or off.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT AND SETUP
BASIC MENU OPERATION
The on-screen menu system provides the viewer with
easy access to adjustments and settings. Just use the
MENU, CURSOR, ENTER, and EXIT keys on the
remote control and follow the on-screen instructions.
Generally, you will use the Cursor ed keys to select a
menu item and the Cursor < > keys to make an
adjustment. The ENTER key confirms a setting. Press
the EXIT key to return to normal TV viewing.
IMPORTANT FACTS:
Some Menu options are specific to Digital and
Analog signals and will vary accordingly.
Also, some options are not available in combination.
Unavailable options will appear “grayed-out” in the
menu. For example, Analog Antenna Signal is not
available when tuned to a Digital Channel.
MENU NAVIGATION MAP
MENU OPTIONS:
MAIN
SUB MENUS
ALL CHANNEL SEARCH
All Channel Search
No
Yes
Use All Channel Search to replace existing Digital and
Analog Channel databases, such as, if you move to
Digital Cable Search
Digital Add-on Search
Analog Antenna Signal
Channel Scan Memory
Digital Caption
No
another city.
Yes
Notes:
No
During All Channel Search, current Digital and Analog
channel databases are deleted and new ones created.
To receive Digital Cable channels, if available, you must
perform a Digital Cable Search.
Yes
Cable
VHF/UHF
Delete?
Add?
To add new digital channels to the existing database,
use Digital Add-on Search, see page 21.
Press the MENU key to display the Main menu.
1
Font Size
Font Style
Background Color
Foreground Color
Background Opacity
Foreground Opacity
Off
Use the CURSOR ed keys to highlight (green) All
Channel Search. Press ENTER.
2
Use the CURSOR d keys to select Yes. Press
ENTER.
3
V-Guide
Picture
On
Adjust
Auto
Manual
Color
Tint
Menu Language
English
Español
Contrast
Brightness
Sharpness
AI
Français
Sound
Auto
Manual
Low
Treble
Bass
Lamp Mode
Start Channel Search?
Mid
High
On
SRS Surround
FOCUS
TruBass (Woofer Level)
Power Management
Lamp Counter Reset
Off
Woofer
No
Yes
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL CABLE SEARCH (OPTIONAL)
DIGITAL ADD-ON SEARCH
This LCD Projection TV can receive unscrambled
(ClearQAM) digital cable channels, when available.
However, not all cable companies provide ClearQAM
digital channels.
Use this feature to add new channels to the digital
antenna channel database. Also, use this feature to add
channels when broadcast towers are in multiple
directions from your location.
Searching for digital cable channels will take about 10
Press the TUNER key to select the Digital Tuner.
1
minutes, please be patient.
Note: When an external input is selected (VIDEO1–3, or
HDMI), press INPUT key to select the Digital Tuner.
DIGITAL
ANTENNA IN
Connect a Digital Cable signal
1
directly to the LCD Projection TV
Press the MENU key to display the Main menu.
Digital Antenna In Terminal.
2
Press the TUNER key to select the Digital Tuner.
2
Use the CURSOR ed keys to highlight (green)
Digital Add-On Search. Press ENTER.
3
Note: When an external input is selected (VIDEO1–3, or
HDMI), press INPUT key to select the Digital Tuner.
Use the CURSOR d key to select Yes. Press
ENTER.
Notes:
4
Press the MENU key to display the Main menu.
3
Use the CURSOR ed keys to highlight (green)
Digital Cable Search. Press ENTER.
Turn your Antenna and repeat these steps for each
direction in which there are transmitting towers.
4
to obtain specific tower and antenna information.
Use the CURSOR d key to select Yes. Press
ENTER.
5
Start Digital Cable Search?
Digital Add-on Search?
Note: After Channel Search is complete, the LCD
Projection TV will tune to the lowest Digital Cable
channel (or lowest Analog channel if no Digital Cable
channel is found).
IMPORTANT FACT: This LCD Projection TV maintains only one
database of digital channels. Therefore, when you search for
ClearQAM digital cable channels, the database of antenna
digital channels will be deleted. You will only be able to receive
those ClearQAM channels your cable company provides.
Cable companies rearrange virtual
Program change
channels as programming changes,
from cable company
which may cause the program you
are watching to move to an-other channel. This message will
appear on the screen briefly to notify you of a change. You will
have to relocate the program you were watching by scanning
through the channels.
Note: If the LCD Projection TV is switched off by pressing the
POWER key or unplugging the AC during Digital Add-On
Search, all channel information detected before the power
loss occurred will be saved.
To restore the antenna digital channel database, reconnect the
antenna and use the menu system to perform an All Channel
Search.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To Delete channels from the Channel Scan Memory
ANALOG ANTENNA SIGNAL
Use the CHANNEL (CH ed) keys or numerical
3
Use this feature to switch between analog off-air
channels and analog cable channels.
keys to select desired channel. HINT: Press the
TUNER key to switch between Digital and Analog
Channel Scan memories.
Press the TUNER key to select analog channels.
1
Press the ENTER key to delete the channel. The
display will change to “Deleted.”
Notes:
4
Press the MENU key to display the Main menu.
2
“Delete?” will
appear below the
channel number if
the selected
channel is already
in the Channel Scan
Memory.
Use the CURSOR ed keys to highlight (green)
Analog Antenna Signal. Press ENTER.
3
Use the CURSOR ed keys to choose Cable or
VHF/ UHF. Press ENTER.
4
Press the EXIT key to return to normal TV viewing.
5
Use the Number
keys to tune to
active channels not
in the Channel Scan
Memory list.
To Add a channel to the Channel Scan Memory
Use the numerical keys 0–9 to select desired
channel number. “Add?” will appear below the
channel number. HINT: Press the TUNER key to
switch between Digital and Analog Channel Scan
memories.
3
Press the ENTER key to add the channel. The
display will change to “Added.”
4
When you have
finished adding
and/or deleting
channels, press
the EXIT key to
return to normal
TV viewing.
CHANNEL SCAN MEMORY
Channel Scan Memory is a list of active channels that
you can scan through using the Channel Scan CH e
(up) CH d (down) keys. This list can be customized by
deleting and/or adding channels.
Press the MENU key to display the Main menu.
1
■ When a digital channel is deleted, all of that channel’s sub-
channels are deleted as well.
Use the CURSOR ed keys to highlight (green)
Channel Scan Memory. Press ENTER.
2
■ Only previously deleted digital channels can be added back
to the Channel Scan Memory.
■ If one digital sub-channel is added back to the Channel
Scan Memory all of that channel’s sub-channels will be
added back.
■ If the last remaining digital channel is deleted, the entire
previous Channel Scan Memory list will be restored
automatically.
■ If the last remaining analog channel is deleted (cable or off-
air channel), ALL analog channels (cable or off-air) will be
restored automatically, regardless of the previous Analog
Channel Scan Memory list.
■ When an external input is selected (VIDEO1, VIDEO2,
VIDEO3, or HDMI), press INPUT key to switch between
Digital and Analog channels.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL CAPTION
Closed-Captioning is hidden textual information
transmitted along with the picture and sound. Turning
Captioning ON causes the LCD Projection TV to open
these captions and superimpose them on the screen.
Because different types of closed-captions can be
transmitted with the picture and sound, separate
captioning modes are provided. The captioning modes
recognized by this model are: Analog EIA-608B and
Digital EIA-708B. Local broadcasters decide which
caption signals to transmit.
TO VIEW CAPTIONS
Press the CAPTION key to select caption modes.
1
Digital modes: Digital CC1 through Digital CC6,
QuikCap, and Off.
Analog modes:CC1 through CC4, QuikCap, and
Off.
CC1
Analog Caption
CHANGINGTHE LOOK OF DIGITAL
CAPTIONS
The Font Size, Font Style, Background Color,
Foreground Color, Background Opacity, and Foreground
Opacity of Digital Captions can be changed.
Notes:
Digital CC1
Digital Caption
If Background Opacity is set to transparent, captions
may be difficult to see.
QUIKCAP OPERATION
Only true EIA 708B Digital Closed-Captions are affected
by all of these settings.
QuikCap turns captioning on and off with the Mute
function. Press the MUTE key on the remote control to
block the TV sound; the captions display automatically,
if available. Press the MUTE key again to restore the
sound. Captions will disappear.
Analog captions generally will not respond to these
adjustments, however, up-converted analog captions
may respond to some options.
Press the TUNER key to select the Digital Tuner.
1
Note: When an external input is selected (VIDEO1–3, or
HDMI), press INPUT key to select the Digital Tuner.
Press the MENU key to display the Main menu.
2
Use the CURSOR ed keys to highlight (green)
Digital Caption. Press ENTER.
3
Use the CURSOR ed keys to highlight (green) an
option.
4
Use the CURSOR < > keys to select the desired
effect.
5
When you have finished making adjustments,
press the EXIT key to return to normal TV viewing.
6
23
Download from Www.Somanuals.com. All Manuals Search And Download.
V-GUIDE (PARENTAL CONTROL)
NOTE: THIS FEATURE IS DESIGNED TO COMPLY WITH
THE UNITED STATES OF AMERICA’S FCC V-CHIP
REGULATIONS. THEREFORE, IT MAY NOT FUNCTION
WITH BROADCASTS THAT ORIGINATE IN OTHER
COUNTRIES.
V-GUIDE RATINGS—AT-A-GLANCE
MPAA (Movie) RATING
TV RATING CONTENT RATING
This Sanyo television is equipped with an electronic V-
Chip to interpret MPAA (Motion Picture Association of
America) and TV Parental Guidelines rating codes. When
these codes are detected, the LCD Projection TV will
automatically display or block the program, depending
upon choices you make when setting up the V-Guide
system. Content ratings are represented by the initials:
FV (fantasy violence), L (adult language), S (sexual
situations), V (violence), and D (suggestive dialog). A
rating icon will generally appear at the beginning of a
program, see chart on page 25
BLOCKED RATINGS
(Lock symbol)
This LCD Projection TV can be set to block programs
with content you deem as inappropriate for your children
to view.
TO BLOCK MPAA ORTV PROGRAM
IMPORTANT FACT: The LCD Projection TV will
automatically block ratings above or unblock ratings
below a selection. For example, if you block TV rating
TV-PG, ratings TV-14 and TV-MA will be blocked
automatically; or if you block Movie rating PG-13,
ratings R, NC17, and X will be blocked automatically.
Press the MENU key to display the Main menu.
1
Use the CURSOR ed keys to highlight (green)
V-Guide. Press ENTER.
2
Use the CURSOR ed keys to select On. Press
Blocking TVY7 does not block higher ratings.
3
ENTER.
TO SETUPV-GUIDE RATINGS
Use the CURSOR d to select Adjust. Press
ENTER.
4
Press CURSOR ed and < > keys to select
MPAA, TV Rating, or Content Ratings. (A green
square appears beside the selected item.)
■ You can block portions of a TV rating by choosing one or
more of the Content ratings (D, L, S, and V). By blocking
just the L and S content ratings of TV-14, for example, TV-
14 rated programs with a D and/or V content rating could
still be viewed.
5
Press the ENTER key to Block or Unblock selected
option. A lock ( ) appears beside the selected
rating option indicating it is blocked.
6
■ V-Guide limits on programming received via the Analog
antenna input, Digital antenna input, VIDEO1 Video input,
and any 480i signals received through the VIDEO2 or
VIDEO3 jacks are controlled by this LCD Projection TV.
When you have finished making adjustments,
press the EXIT key to return to normal TV viewing.
7
■ V-Guide limits on digital programming received through the
Component jacks (VIDEO2 or VIDEO3) are controlled by
the external devices connected to those jacks (such as a
DVD Player or Satellite Receiver). Refer to your external
device’s owner’s manual for instructions on setting V-
Guide limits.
■ Networks and local stations may or may not include the
content ratings portion of the TV Parental Guidelines.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TO TEMPORARILY UNBLOCK MPAA ORTV
PROGRAM
TV RATINGS (AGE/CONTENT-BASED)
ALL CHILDREN—Program is designed to be
appropriate for children from ages 2–6.
Press the MENU key to display the Main menu.
1
DIRECTED TO OLDER CHILDREN—Program is
designed for children 7 and above. Material may
include mild fantasy violence (FV) or comedic
violence.
Use the CURSOR ed keys to highlight (green)
V-Guide. Press ENTER.
2
Use the CURSOR ed keys to select Off. Press
ENTER.
3
This will temporarily set V-Guide to Off. When V-Guide
is reset to On (follow steps 1–2), the LCD Projection TV
will automatically revert to previously selected block
ratings.
GENERAL AUDIENCE—Program suitable for all
ages. Contain little or no violence, no strong
language or sexual dialogue or situations.
PARENTAL GUIDANCE SUGGESTED—Program
contains material that may be unsuitable for
younger children. Material contains one or more
for the following: moderate violence (V), some
sexual situations (S), infrequent coarse language
(L), or some suggestive dialogue (D).
TO UNBLOCK/BLOCK ALL MPAA OR ALLTV
PROGRAM
Press the MENU key to display the Main menu.
1
Use the CURSOR ed keys to highlight (green)
V-Guide. Press ENTER.
2
PARENTS STRONGLY CAUTIONED—Some
material is unsuitable for children under 14 years
of age. Parents are strongly urged to use caution
against letting children under age 14 watch
unattended. Material contains intense violence (V),
intense sexual situations (S), strong coarse
language (L), or intensely suggestive dialogue (D).
Press ENTER to select Adjust.
3
Highlight the “Allow All” or “Block All” option
4
using the CURSOR ed and < > keys, if needed.
Press ENTER.
MATURE AUDIENCE ONLY—Program is designed
specifically to be viewed by adults and therefore
may be unsuitable for children under 17 years of
age. Material contains graphic violence (V), explicit
sexual activity (S), or crude indecent language (L).
MPAA MOVIE RATINGS (AGE-BASED)
G
PG
G
GENERAL AUDIENCES—All ages admitted.
4
14
A
MA
PG
PARENTAL GUIDANCE SUGGESTED—Some material
may not be suitable for children.
AS
7
Y7
PG-13 PARENTAL GUIDANCE CAUTIONED—Some material
may be inappropriate for children under 13.
R
RESTRICTED—Under 17 requires accompanying
parent or adult guardian
When codes are being transmitted and received, and V-
Guide is set to On, the V-Chip blocks programming
according to the settings you choose.
NC-17 NO ONE 17 AND UNDER ADMITTED
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE ADJUSTMENT
MENU LANGUAGE
Press the MENU key to display the Main menu.
Press the MENU key to display the Main menu.
1
1
Use the CURSOR ed keys to highlight (green)
Picture . Press ENTER.
Use the CURSOR ed keys to highlight (green)
Menu Language. Press ENTER.
2
2
Use the CURSOR ed keys to highlight (green)
Auto (factory preset settings) or Manual. Press
ENTER.
Use the CURSOR ed keys to select English,
Español, or Français.
3
3
Press the EXIT key to return to normal TV viewing.
4
MANUAL ADJUSTMENTS
Use the CURSOR ed keys to select the option
you want to adjust.
4
Then use the CURSOR < > keys to make an
adjustment.
5
When you have finished making adjustments, press
the EXIT key to return to normal TV viewing.
6
■ The AI Function analyzes scenes and automatically adjusts
peak brightness according to the brightness of the image.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND ADJUSTMENT
LAMP MODE
Press the MENU key to display the Main menu.
Use this feature to change the brightness of the
projection lamp.
1
Use the CURSOR ed keys to highlight (green)
Sound. Press ENTER.
Press the MENU key to display the Main menu.
2
1
Use the CURSOR ed keys to highlight (green)
Auto (factory preset settings) or Manual. Press
ENTER.
Use the CURSOR ed keys to highlight (green)
Lamp Mode. Press ENTER.
3
2
Use the CURSOR ed keys to select Low, Mid, or
High.
3
MANUAL ADJUSTMENTS
Low—Lower brightness than “Mid”; this option
reduces the lamp power consumption.
Mid—Normal brightness
Use the CURSOR ed keys to select the option
you want to adjust.
4
High—The brightest mode
Then use the CURSOR < > keys to make an
adjustment.
5
Press the EXIT key to return to normal TV viewing.
4
When you have finished making adjustments,
press the EXIT key to return to normal TV
viewing.
6
SRS Surround—SRS Surround can be effective when set to On.
FOCUS—Provides clear sound when set to On.
TruBass—The TruBass levels (Off, Low, Mid, High) can be selected.
Woofer—When the Woofer option is set to On, the sound can be
output from the Woofer jack; the TruBass option is
changed to “Woofer Level” and it can be adjusted (Off,
Low, Mid, High).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER MANAGEMENT
LAMP COUNTER RESET
For reducing power consumption as well as maintaining
the lamp life, Power Management turns off the lamp
when the LCD Projection TV is not used for a certain
period.
Be sure to reset the lamp counter after the lamp is
replaced. When the lamp counter is reset, the LAMP
REPLACE indicator will be turned off.
Press the MENU key to display the Main menu.
1
If the input signal is interrupted and no button is pressed
for more than 30 seconds, the timer display with “No
signal” appears on the screen and it starts the five
minutes countdown. During this period, when the signal
previously selected is connected or any button on the
remote control or on the side panel is pressed, the the
LCD Projection TV will be turned on again.
Use the CURSOR ed keys to highlight (green)
Lamp Counter Reset. Press ENTER.
2
Use the CURSOR d key to select Yes. Press
ENTER.
3
Another confirmation screen appears. Use the
CURSOR d key to select Yes. Press ENTER.
4
Press the EXIT key to return to normal TV viewing.
5
When the countdown time has elapsed, the LCD
Projection TV will be turned off automatically and the
POWER indicator will light orange, and then turned off
after the LCD Projection TV has cooled down enough.
Press the MENU key to display the Main menu.
1
Use the CURSOR ed keys to highlight (green)
Power Management. Press ENTER.
2
Use the CURSOR d key to select On.
3
Press the EXIT key to return to normal TV viewing.
4
Lamp counter reset?
Use this feature only after replacing the
lamp in your PTV.
■ Do not reset the lamp counter without implementing the
lamp replacement. Be sure to reset the lamp counter only
after replacing the lamp.
■ The lamp counter cannot be reset even if you press the
RESET key on the remote control. See page 19.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
HELPFUL HINTS (PROBLEMS/SOLUTIONS)
Because of the Quality we build into our product, very
your problem. If the problem still persists after following
all operating instructions, contact the dealer where you
purchased the LCD Projection TV or Sanyo Fisher
customer service. Specify the model number and explain
about the problem. We can Help!
few problems are actual LCD Projection TV defects.
Most problems only involve simple hookup or setup
changes that can be solved by the customer. Please
check the chart below and try the solutions listed for
Try these Solutions
Page No.
Problem:
Check these Conditions
●
●
PTV turns off
automatically
The sleep timer may have been set.
Press POWER key.
19
●
●
No picture, sound
(Digital Picture).
Check antenna/external connections.
Adjust antenna.
●
●
May be station trouble, NO signal broadcast. Try a different channel.
7, 19
●
●
●
●
●
●
MUTE function may be on.
Press RESET key to restart channel search.
Adjust Volume.
●
●
No Captioning.
Check if station is broadcasting a Closed-
Caption signal. Select another channel.
Press Caption key to select Captioning.
23
23
19
●
●
Cannot customize
Caption.
Digital Caption signal not broadcast.
Press CAPTION key to select Analog captioning.
Cannot display picture
on a full screen.
Check Aspect Ratio of broadcast.
Press PIX SHAPE key to change setting.
●
●
Pixilation of Digital
image.
Press INFO key and check the signal
strength.
Turn antenna, install signal booster.
Install outdoor Digital antenna.
7, 18
●
●
●
●
●
●
●
●
●
Poor picture/sound.
Check if program is in color.
Check antenna/external connections.
Color or Tint misadjusted.
May be station trouble.
Try a different channel.
Adjust antenna.
Press RESET key to restart channel search.
Adjust Volume.
7, 19, 26, 27
MUTE function may be on.
●
●
●
●
●
●
“No Signal”
message appears on
the screen.
Check Audio/Video connections.
Check external equipment connections.
Check external equipment setting.
Press INPUT key.
Switch on external equipment.
Set external equipment output connections to match
input connections.
12–17
19
●
●
●
●
No DTV Stereo or
SAP sound.
No UHF, VHF
Channels OK.
Check if station is broadcasting a true MTS
stereo signal or a SAP signal.
Press AUDIO key.
Cable Channel indicator C should not appear Switch Analog antenna signal to VHF/UHF.
22
22
next to the channel number.
Cannot select or scan
some channels.
●
●
●
●
●
●
Channel may be removed from memory.
Check antenna connections.
No digital signal being broadcast.
Signals are weak.
Select Channel Scan Memory and manually add channels
or start CH. (channel) search.
Turn Antenna or install signal booster.
Set V-Guide to “None” or press the RESET key to clear
all settings and restart channel search.
●
●
24–25
19
V-Guide is set to block programming.
●
●
No Cable channels
above number 13.
Cable Channel Indicator C should appear
next to channel number.
Switch Analog Antenna signal to Cable.
22
●
●
●
●
Remote Control
will not work.
Check batteries
Make sure PTV is plugged in.
Replace batteries two “AAA.”
Aim remote control at front of PTV.
8
18–19
●
●
Cabinet makes
popping sound.
This is a normal condition during warm-up
and cool down of the plastic cabinet parts.
●
●
Power is shut down
and WARNING
indicator flashing red.
The temperature inside the PTV is
abnormally high.
Wait until the PTV to cool down. When the temperature
inside the PTV returns to normal, you can turn on the
PTV again. (The WARNING indicator will be turned off as
you turn on the PTV.)
30
30
●
WARNING indicator
lights red and PTV
cannot be turned on.
An abnormal condition is detected in the
PTV.
Unplug the AC power cord once and plug it again to turn
on the PTV. If the PTV is turned0 off again, call for
service.
WARNING :
High voltages are used to operate this LCD Projection TV. Do not attempt to open the cabinet.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
CLEANINGTHE LCD PROJECTIONTV
The surface of the cabinet can be damaged if not properly maintained. Many
common household aerosol sprays, cleaning agents, solvents, and polishes will
cause permanent damage to the fine surface.
1. Unplug the power cord before cleaning the LCD Projection TV.
2. Gently wipe the screen and cabinet with a dry soft cloth.
The screen is likely to be damaged if it is not maintained properly. Do not use
hard objects like a hard cloth or paper. Do not use solvents or abrasives.
Note: Never spray liquids on the screen because they can run down and drip onto the
chassis. This may cause component failure not covered under Warranty.
WARNING INDICATOR
The WARNING indicator shows the state of the function which protects the LCD
Projection TV. Check the state of the WARNING indicator and the POWER
indicator to take proper maintenance.
FRONT PANEL
The LCD Projection TV is shut down and the WARNING indicator is flashing red
AMP
When the temperature inside the LCD Projection TV exceeds the normal
temperature, it is automatically shut down to protect the LCD Projection TV. The
POWER indicator flashes red while the LCD Projection TV is being cooled down.
When the temperature inside the LCD Projection TV returns to normal, the
POWER indicator is turned off and then it can be turned on.
WARNING
PLACE
Note: The WARNING indicator continues to flash even after the temperature inside the
LCD Projection TV returns to normal. When the LCD Projection TV is turned on again, the
WARNING indicator stops flashing.
WARNING
flashing red
Then check the item below:
✓ Did you provide appropriate space for the LCD Projection TV to be ventilated? Check the
installation condition to see if ventilation slots are not blocked.
✓ Has the LCD Projection TV been installed near an Ar-Conditioning/Heating Duct or Vent?
Move the installation of the LCD Projection TV away from the duct or vent.
The LCD Projection TV is shut down and the WARNING indicator lights red
FRONT PANEL
When the LCD Projection TV detects an abnormal condition, it is automatically
shut down to protect the LCD Projection TV and the WARNING indicator lights
red. In this case, unplug the AC power cord and plug it, and then turn the LCD
Projection TV on once again to verify operation. If the LCD Projection TV is turned
off again and the WARNING indicator lights red, unplug the AC power cord and
contact Sanyo Fisher customer service.
LAMP
WARNING
PLACE
CAUTIONS
WARNING
lights red
DO NOT LEAVE THE LCD PROJECTION TV WITH
THE AC POWER CORD CONNECTED UNDER THE
ABNORMAL CONDITION. IT MAY RESULT IN FIRE
OR ELECTRIC SHOCK.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
LAMP REPLACEMENT
The projection lamp has a service life and it needs to be
replaced when it reaches the end-of-life. When the lamp of
this LCD Projection TV reaches the end-of-life, the LAMP
REPLACE indicator will light yellow. If this indicator turns to
yellow, replace the lamp with a new one promptly.
FRONT PANEL
LAMP
REPLACE
WARNING
This indicator will light
yellow when the projection
lamp reaches the end-of-life.
CAUTION
CAUTION
Allow the LCD Projection TV to cool, for at least 30
minutes before you open the Lamp cover. The inside
of the LCD Projection TV can become very hot.
For continued safety, replace with a lamp of the
same type. Do not drop a lamp or touch a glass bulb!
The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
Turn off the LCD Projection TV and unplug the AC
power cord. Allow it to cool for at least 30 minutes.
1
Press the latches on both sides of the front cover
and pull the front cover forward.
2
Press and hold
this button and
pull the front
Loosen the screw that secures the lamp cover with
a screwdriver and remove the lamp cover.
3
cover forward.
Press the latch
on both side.
Loosen the two (2) screws that secures the lamp
assembly and pull out the lamp by holding the holes
on both sides.
4
Replace the lamp with a new one and secure it with
the two (2) screws. Make sure that the lamp is
seated properly into the lamp compartment. (Refer
to page 32 for ordering the replacement lamp.)
5
Put back the lamp cover and secure it with the
screw, and then put back the front cover.
Loosen the screws.
6
Connect the AC power cord to the Power Cord
Connector and turn on the LCD Projection TV.
Lamp cover
7
Reset the lamp counter. See “Lamp Counter Reset”
on page 28.
8
CAUTION
When installing the new lamp into the lamp
compartment, make sure the lamp socket is
securely plugged into the compartment socket.
Improper or loosen socket connection may cause
arc discharge resulting fire hazard.
Loosen two screws.
Hold here and pull out
the lamp.
(There are holes inside)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
LAMP HANDLING PRECAUTIONS
This LCD Projection TV uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of
the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than
other similar lamps.
● If the LCD Projection TV indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the LCD Projection TV has cooled down.
(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp
with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime
draws to an end. Risk of explosion may differ according to the environment or conditions in which the LCD
Projection TV and lamp are being used.
IF THE LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If the lamp explodes, unplug the LCD Projection TV’s AC power cord from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to
ensure that there are no broken shards or pieces of glass around the LCD Projection TV or coming out from the
cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the
inside of the LCD Projection TV except those who are authorized trained technicians and who are familiar with the
LCD Projection TV service. Inappropriate attempts to service the unit by anyone, especially those who are not
appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering the projection lamp, give the
following information to the dealer.
● Model No. of your PTV
:
:
PLV-55WHD1/PLV-65WHD1
POA-LMP96
● Replacement LampType No.
(Service Parts No. 610 322 7382)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Screen Size (Measured Diagonally):
PLV-65WHD1: 65-inches/PLV-55WHD1: 55-inches
LCD Panel System:
PLV-65WHD1: 120 V, 2.8A
Size and Weight (approximately):
PLV-65WHD1
0.7” wide TFT Active Matrix type, 3 panels
Panel Resolution:
Width:
Height:
Depth:
60.6” (1538 mm)
40.0” (1016 mm)
18.4” (468 mm)
1280 x 720 dots
Number of Pixels:
2,764,800 (1280 x 720 x 3 panels)
Signal Compatibility:
NTSC; 480i, 480p, 1080i, 720p
Scanning Format:
720p (All Signals are Converted to 720p)
RF Antenna Input:
Weight:
PLV-55WHD1
Width:
106.0 (lbs) 48.1 (kg)
50.9” (1294 mm)
34.0” (864 mm)
15.6” (397 mm)
86.4 (lbs) 39.2 (kg)
Height:
Depth:
Weight:
Environmental Considerations:
Analog–UHF/VHF/CATV 75ohm
Digital–75 ohm
Operating Temperature: 41˚F–95˚F (5˚C–35˚C)
Storage Temperature:
14˚F–140˚F (-10˚C–60˚C)
Jacks and Connectors:
Remote Control:
Video 1 Input:
Video 2 Input:
Video 3 Input:
Composite Video/S-Video
and Audio L/R
Component (Y/Pb/Pr) with
Audio L/R Input
Component (Y/Pb/Pr) with
Audio L/R Input
Battery :
Operating Range:16.4’ (5 m)/ 30
Dimensions:
Net Weight:
1.5 V AAA Alkaline type x 2
7.72” (L) x2.15” (W) x 0.83” (H)
(196 mm x 54.7 mm x 21.0 mm
2.96 oz (84 g)
(without batteries)
Digital Audio Output: Dolby® Digital (Optical)
Analog Audio Output:Audio L/R (Fixed)
HDMI Input:
Accessories:
Owner’s Manual
AC Power Cord
Remote Control
19-pin connector
(Picture/Sound with HDCP)
RCA Type
D-Sub (HDB 9)
Woofer Output:
Service Jack:
Sound:
Two Speakers, size: 5.0” x 3.0” (128 x 77 mm)
Amplifier:
Specifications are subject to change without notice.
Built-in with 15.0 W/ch
Power Requirement:
Source: AC 120 V, 60 Hz
AC Power Consumption (average):
PLV-55WHD1: 120 V, 2.8A
LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Contains iType and Scaleable fonts from Monotype Imaging, Inc.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
Unit: inch (mm)
PLV-65WHD1: 60.6 (1538)
PLV-55WHD1: 50.9 (1294)
PLV-65WHD1: 18.4 (468)
PLV-55WHD1: 15.6 (397)
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, specify item name and Type No. to the
sales dealer.
● LCD Projection TV stand
Type No.: PLV-5565STD (for both PLV-55WHD1 and PLV-65WHD1)
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
Part No. 610 329 9211 (1AA6P1P5187-- M8PA)
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|