POA-LN02
LD-Net Organizer
Network Capture 3
Network Viewer 3
Network Communication
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance and Caution
CautioN oN use iN Network
- When you receive an alert e-mail from the monitor, you must check the monitor
immediately. Fire or accident may result if the monitor is used in an abnormal condition.
- When you install the monitor at remote location and use it through the network, you
must perform the safety inspections periodically. In this case you must pay attention to
the change of environment in which you installed the monitor. It may cause fire or an
accident depending on the change of environment.
CautioN
SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data or
damage of the computer caused by using this product.
The CE Mark is a Directive conformity mark of the European Community (EC).
NOTES ON Lithium Battery (CALIFORNIA USA ONLY)
This product uses a Lithium Battery which contains Perchlorate Material - special han-
dling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Notas acerca de pilas de litio (SOLO PARA CALIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene el material perclorato – puede ser nece-
sario una manipulación especial.
Consulte la página www.dtsc.ca.gov/hazardouswaste/perchlorate
ꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Compliance..........................................................................................................................................................................2
Operating environment of LD-Net Organizer............................................................................................. 11
Chapter 2 Installation...............................................................................................15
Flow of installation........................................................................................................................................................16
[2] Installation and network configuration....................................................................................................18
Mounting ..................................................................................................................................................................18
Network configuration.....................................................................................................................................21
Network PIN code setting..............................................................................................................................25
Chapter 3 Basic Setting and Operation.............................................................29
1 Enter the IP address........................................................................................................................................30
3 Display of main setting page ...................................................................................................................31
How to use the setting page.................................................................................................................................32
Initial setting.....................................................................................................................................................................34
Network PIN code setting..............................................................................................................................35
Date and time setting.......................................................................................................................................36
Network configuration...............................................................................................................................................37
E-mail setting...................................................................................................................................................................38
Chapter 4 Controlling the Monitor .....................................................................45
Picture adjustment ............................................................................................................................................49
PC adjustment.................................................................................................................................................................51
Timer setting....................................................................................................................................................................55
Check the timer events....................................................................................................................................56
Monitor information....................................................................................................................................................58
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Multi-control.....................................................................................................................................................................59
Controlling and setting the multi-monitors.......................................................................................59
Chapter 5 Network Capture...................................................................................65
Commands on the task bar...........................................................................................................................66
Parameter set up..................................................................................................................................................67
Join the communication (only for Sub PC).................................................................................. 75
Exit from the communication (only for Sub PC) ....................................................................... 75
Acquire and release of editing authority..............................................................................................75
Edit capture image..............................................................................................................................................76
Chapter 6 Network Viewer.....................................................................................81
Creating a program file [Program Editor].......................................................................................................87
Chapter 7 Appendix ................................................................................................97
Examples of connection...........................................................................................................................................98
Web browser setting................................................................................................................................................100
Examples: OS/Browsers...........................................................................................................................................101
Port specification........................................................................................................................................................106
Q&A......................................................................................................................................................................................107
ꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
Features
real time Capture function ( p.68)
To display the screen image of
PC1
PC2
PC4
the computer by the monitor
through the network in real
time.
Capture
PC3
PC6
PC5
Network Communication function ( p.71)
To communicate by sharing the
captured image of a computer
with multiple computers and
a monitor. User can draw the
text and figure on the captured
image by using a drawing tool.
MONITOR 1
Capture
PC6
PC1
PC2
PC5
Capture a screen
image of PC5 and
make marking with a
tool.
Network Viewer function ( p.81)
To acquire the JPEG image data
from the file servers placed in
the network and display them
by the monitor.
MONITOR 2
MONITOR 1
PC1
PC2
JPEG
PC3
PC4
PC6
PC5
Prog.
JPEG
FTP file server
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
web Management function ( p.45)
With this function, you can
MONITOR 2
MONITOR 1
check monitor functions such
PC1
PC2
as power status, input mode,
signal condition, etc. through
the network by using the web
browser installed on your com-
puter.
PC3
PC4
PC6
PC5
Turn ON
MONITOR 2
e-mail alert function ( p.38)
The monitor (Network Unit)
sends messages to the regis-
MONITOR 2
MONITOR 1
PC1
PC2
tered e-mail addresses when a
internal temperature abnormal-
ity or power failure occurs with
the monitor.
PC3
PC4
PC6
PC5
You’ve got
Mail.
ꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
sNMP agent function ( p.42)
MONITOR 1
MONITOR 2
MONITOR 3
MONITOR 4
To send the information of the
monitor to the SNMP manager.
Enables you to manage the
monitor condition with the sup-
plied SNMP manager software.
Trap
PC6
PC5
You received
a Trap.
Trap
SNMP Manager
Multi-control function ( p.59)
A single computer can con-
MONITOR 1
MONITOR 2
MONITOR 3
MONITOR 4
trol and set up the multiple
monitors at the same time.
PC6
PC5
PC4
Select Input2 for
MONITOR 1 to
MONITOR4.
automatic on/off using Clock function ( p.55)
Automatically turn on or off the
monitors at specified date/day
and time by using the clock func-
tion.
I am ready to turn ON,
and select Input 3 (Video)
Now it’s 11:30
sNMP Manager function (refer to the separated booklet)
A function to manage the
ITOR 1
MONITOR 2
MONITOR 3
MONITOR 4
condition of monitors in the
network by using the SNMP
protocol. The managing com-
puter needs to provide an
SNMP managing software. Refer
to the owner's manual of the
"PJ Network Manager" supplied
separately for further details.
Trap
PC6
PC5
PC4
You received
a Trap.
Trap
SNMP Manager
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Environment
operating environment of LD-Net organizer
To perform the managing and setting of the monitor by using this product, the environ-
ment described below is required.
Standard mode
Windows 98, Windows Me, Windows NT4.0SP6
Windows 2000, Windows XP
Operating System
Higher than Pentium III 900MHz
Recommended CPU
Memory
64MB (Minimum)/ 128MB or more(Recommended)
128MB or more for WindowsXP
100MB or more
HDD free area
CD-ROM drive
Drive equipment
Support one of following resolutions;
VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of col-
ors: Either of 16 bit (65,536 color 24/32 bit (16,77 million colors))
Display setting of
computer
The computer must provide a 10Base-T or 100Base-TX network
card.
Network card
Internet Explorer version 5.0, 5.5 or 6.0
Netscape Navigator version6.2, 7.0 or 7.1
* Used to control and set up the monitor. The layout of pages in the
browser may slightly differ from each type of application or oper-
ating system you use.
Web Browser*
Adobe Flash Player version 6,0,79,0(6.0r79) or later
Plug-Ins
- Microsoft Outlook
- Netscape Mail
* Required the internet e-mail application software to receive an
e-mail alert sent from this product. If you do not use the function
E-mail Alert, this application is not required.
- Microsoft Outlook Express
Internet Mailer*
- FTP server (Windows 2000 Professional or Windows XP
Professional)
* The FTP service provided with the Windows 2000 Professional
or Windows XP Professional is required when using the Network
Viewer function.
FTP Service *
* For the operating environment of PJ Network Manager, refer to an owner's manu-
al in the document CD-roM.
PDa restriction
1
The PDA can be used for the Light mode* only. The operating system of the PDA is
PocketPC2002 or higher. The version of the Adobe Flash Player is 6,0,81,0 or higher.
*1 The "Light Mode" and "Standard Mode" will be explained on item "Display Mode" ( p.30-32)
11
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
*1
the limitation of connection between this product and hub or computer
Suitable LAN cables are limited by length and type as follows;
Connection
Type of usable LAN cable
Maximum length
100m
2
Network Unit - Hub
UTP Straight Cable with category 3 or 5 *
2
Network Unit - Computer UTP Cross Cable with category 3 or 5*
100m
*1 There may be other limitations depending on your network environment or LAN specification.
Please consult your network administrator for further details.
*2 Category of LAN cable indicates the cable quality. Normally, a cable with category 3 or 5 is used
for 10Base-T network, and a cable with category 5 is used for 100Base-TX network.
Before use
Package contains
The package contains following items. Check each item as you unpack the package. If you
have any of the following items missing, contact the sales dealer.
Network unit
1 piece
T
C
A
K
N
I
L
Q
Guide
u
ic
k
S
e
tu
p
Quick Setup Guide
English
1 piece
1 piece
Software CD-ROM
NetworkViewer&Capture3software
PJNetworkManagersoftware
Document CD-ROM
1 piece
LD-NetOrganizerOwner'sManual
PJNetworkManagerOwner'smanual
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Notice
expression/abbreviation
The word "monitor" found in this manual means "monitor provided with Network unit"
unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows XP
Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruc-
tion procedures may differ from the actual operation depending on your computer envi-
ronment.
use of this manual
This manual does not provide the description of basic operation and functions for com-
puter, web browser, monitor and network. For instructions about each piece of equipment
or application software, please refer to the respective booklet.
trademarks
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows
NT are registered trademarks of Microsoft Corporation. Internet Explorer is a registered
trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator are
trademarks or registered trademarks of Netscape Communications Corporation. JavaScript
is a registered trademark of Sun Microsystems, Inc.
Other product or brand names in this manual are registered trademarks or trademarks of
their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
Basically this manual is described for Monitor set CE52LH1. Some instruction procedures may differ
from the actual operation depending on the connected Monitor set type.
1ꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Flow of installation
The following are instructions for attaching this product to the monitor and connecting it
to the network. Please review the entire procedure to become familiar with it.
Function of the network unit ( p.17)
Explains the name and functions of each part of the network unit.
1
2
installation and network configuration ( p.18-25)
1 Mount this product onto the monitor.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the network unit.
4 Set the Network PIN code.
installation of the software ( p.26-28)
Explains how to install the software Network Viewer & Capture 3 into your com-
puter.
3
set up is complete
The preparation is completed to control the monitor connected to the network. At next
step, set up and control the monitor via the network by using the web browser installed
on your computer. Please see chapter 3 "Basic setting and operation". ( p.29)
1ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Name and function of each part
[1] Name and function of each part
(top View)
Power indicator
Mounting screws
Mount by using a coin etc. ( p.18)
aCt indicator
This turns on and off with green when
sending or receiving of data
LiNk indicator
This lights up red when the network unit is
connected to the network correctly.
(Bottom View)
Connector plug
Connecting to the terminal on the
monitor. ( p.18)
serViCe 1
Only for service use.
serViCe 2
Only for service use.
LaN port
Connecting the LAN cable. ( p.19)
17
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
[2] installation and network configuration
Mounting
1 Disconnect the AC plug from the monitor.
2 Remove the screws on the back of the cabinet, and then remove the terminal covers.
3 Insert the network unit into
the monitor, and fix it with the
screws.
!
Caution
The AC cord must be disconnected from AC power outlet when mounting or removing this prod-
uct. It may damage the product.
Do not connect the AC cord until after connecting the LAN cable and computer.
1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
4 Set the Option Switch from the UP position to the DOWN position.
Cannot use the serial port of the monitor in this position. Set back to the UP position
when the network unit is not used.
Up
Position
Down
Position
1ꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Connection of LaN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable
with RJ-45 plug. There are two different types of cables depending on whether the network is
constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distrib-
ute the network cable if required.
1 Disconnect the AC plug from the monitor.
2 Connect the UTP straight cable to the LAN port on the network unit.
3 Connect the UTP straight cable to the hub.
Hub
(10Base-T, 100Base-TX)
Monitor
UTP straight cable
The AC cord must be disconnected from AC power outlet when connecting the cable. It may
damage the product.
When you set up the network which has a default setting by using computer, it must be carried
out in the network which does not connect to other monitors.
Use the UTP cross cable when you connect the computer and monitor directly not using the hub.
When you connect the monitor into the 10Base-T network, use cable with category 3 or 5. When
you connect the monitor into the 100Base-TX network, use cable with category 5.
The length of cable between hub and monitor should be less than 100m.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
Network configuration
When you connect a monitor to a network, the network number of monitor must be the
same as the network you intend to connect. You should configure monitors network first.
Make sure that the monitor is connected to the network correctly. To configure the net-
work, use the computer. Refer to the chart below.
Procedure of Connecting the monitor to the network
Configure the network with computer
p.22
Please see further
informatin on pages
22-25.
Temporarily set up the computer's
network with the default network
number of the LD-Net Organizer.
Example of computer's configuration
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Default Gateway : (blank)
DNS : (blank)
Restart the Computer, if required
Please see further
informatin on pages
30-37.
Using the web browser and login to
the setting page of the LD-Net
Organizer by accessing the default
IP address.
Default Network Address of the
LD-NetOrganizer
IP Address : 192.168.0.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
DNS : 0.0.0.0
Change the network address you
want to connect to the existing
network through the setting menu
on the browser.
Example of monitor's configuration
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
DefaultGateway:192.168.1.1
DNS : 0.0.0.0
Restart the LD-Net Organizer
Reset to the computer's original
network configuration.
Completing the network configuration. Perform the basic
setting and operation of the monitor by using the web
browser. Please see chapter "3: Basic Setting and
Operation" on page 29 for further information.
ꢀ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Configure the network with the computer
This example explains how to set the following configuration.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.1.201
: 255.255.255.0
: 192.168.1.1
: 0.0.0.0
The default network configuration is set as follows.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
Make sure that the monitor is connected to the network and then connect the AC cord to
the outlet.
1
1 Temporarily* set up your computer network configuration to the same IP network number
as the LD-Net Organizer. For example, change your computer network configuration
as follows and restart the computer.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
: 255.255.255.0
: (blank)
: (blank)
The network configuration of computer differs depending on each network environment
or your computer. For further information, please see the chapter “Configure the network
of computer” on page 24.
*1 Change your computer's network configuration temporarily. After completing the set up for the
monitor, you must set up again to the original network configuration for your computer. It is rec-
ommended to make a note of those network settings.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
2 Configure the network of the monitor by using the web browser.
1. Enter the IP address of the monitor as the
URL. The login page will be displayed and
login. For further information, please see
chapter “3: Basic Setting and Operation” on
page 29.
2. Configure the network through the setting page on the browser. For further information, please
see chapter “Network Configuration” on page 37.
Completing of installation
Now the installation is completed. The IP address of this monitor has been set to “192.168.1.201”.
You must reset the network configuration of the computer to the original and restart the com-
puter.
Next, please see chapter “Basic Setting and Operation” on page 30. It describes how to operate
and set up the monitor.
If you use a cable to connect the monitor and computer directly, without using a hub, you must
use a UTP cross cable. In this case, you cannot access the login page if the setting of web browser
is set to “Use proxy server”. It must be changed to the “Not use proxy server”. For further informa-
tion, please see the “Web browser setting” of chapter "Appendix" on page 100.
When you set up the network of monitor which has a default setting by using the computer, it
must be carried out in the network which does not provide any gateways (routers).
ꢀꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Configure the network of computer
When you use the monitor through the network, the IP address of the monitor must have the
same IP network number of the existing network. Also it is required to use the same IP network
number of the computer to set up the monitor. In the network included with the gateway
(router), it must be used with the IP network number specified by the gateway (router).
Configure the computer's network by following steps:
This example explains how to set the following network address.
IP Address
Subnet Mask
Gateway Address
: 192.168.0.5
: 255.255.255.0
: 192.168.0.1
1 Select the Control Panel menu from the [Start] menu. Click
the Network and internet Connection and then click the
Network on the control panel.
2 Click the Local area Connection icon with right button of
the mouse and then select the Property menu. The right
3 wSeinledcotwthweillGaepnpeearraol ntatbheosncrteheen."Local Area Connection
Proper ties" dialog window. Selec t the inte rnet
1
Protocol(tCP/iP)* and then press the Properties button.
4 On the "Internet Protocol (TCP/IP) Properties" dialog win-
dow, select the use the following iP address button and
2
5 tEhnetenretnhteeDr tehfeauIPltagdadterewsasy* aadnddreSsusb. net mask.
This setting is not needed if the network does not pro-
vide the gateway (router).
6 Click the ok button, the setting window will be closed.
*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the column,
you need to install the TCP/IP protocol. For further information refer to the user's manual of your
computer.
*2 If the network already has the TCP/IP protocol set, enter with the same IP network number for the
IP address and Subnet mask.
*3 There are some ways to set up the network depending on your computer's appearances.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
Network PiN code setting
The Network PIN code can be set to restrict access to the setting page of the monitor
using the web browser.
Default Network PiN code [0000] means no Network PiN code is set.
It is recommended to set up the Network PIN code when you connect the monitor to the net-
work. This setting is carried out through the web browser. For further information, refer to item
"Initial setting/Network PIN code setting" ( p.35).
Notice about system construction
For installation of multiple monitors into the same network with network
unit.
Do not install multiple monitors with network units that have their default network set-
tings to the same network. The use of the network units which have the default IP address
set to the same network settings will cause IP addresses to collide and create a malfunc-
tion. When you install multiple monitors into the same network, configure the network
with the following steps.
1. Change the IP address from the default IP address. Please see item "Network configura-
tion" for further information ( p.21).
2. Make sure that there is no network equipment set with the same IP address in the net-
work before connecting to the network.
3. When installing other monitors, follow the above steps to change the IP address and
connect to the network.
in case of installing the monitor with network unit into the network con-
structed with the DHCP/BootP server.
This network unit does not support the DHCP/BOOTP server. The static IP address must be
manually configured. To use this product in this network environment, set it up so that the
DHCP/BOOTP server does not assign the IP address configured to this product for another
device on the network. Please consult your network administrator for further information.
ꢀꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
[3] installing the software
It is required to install the software into your computer to use the Network Capture func-
tion and Network Viewer function. Please install the software as follows.
Note: to install the software into the computer with windows 2000, windows XP
or windows Nt, you should logon as administrator. Before installation, make
sure that the other applications are closed, otherwise proper installation
cannot be made.
Network Viewer & Capture 3 installation
1 Set the supplied Network Viewer & Capture
3 CD-ROM into the CD-ROM drive of your
computer. Double click setuptool.exe icon
in the "Tool" folder in the CD-ROM.
2 Select "English [United States]" from the
pull-down menu on the "Choose Setup
Language" window and click ok button to
start installing and then follow the installa-
tion wizards.
As the "License Agreement" will appear, read
contents carefully and click Yes button if you
agree to the license agreement to proceed
with installing.
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the software
installed software
The following 3 software are installed on your computer.
c Network Capture 3:
Capture the displayed image of the computer and serve it to the monitor via the net-
work.
This software is registered into "startup folder" of the computer and the capture icon
stays on the task bar after booting the computer.
c Network Viewer 3 (File Converter 1):
1
Converts to the JPEG* data format which can be displayed with the monitor from the
JPEG, bitmap and Power Point files.
c Network Viewer 3 (Program Editor) :
This is a tool to make the program which has a function to specify and order the display-
ing JPEG image data stored in the file servers.
* To uninstall these software, use "Add/Remove Program" from the control panel.
*1 This product supports the JPEG image format. This file is needed to convert to the optimized JPEG
file by using the File Converter 1 software previously. Refer to the item "Creating the available data
[Network Viewer 3]"( p.82) about data converting for the display.
ꢀ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
File Converter 2 installation
1 Set the supplied Network Viewer & Capture
3 CD-ROM into the CD-ROM drive of your
computer. Double click setupDrv.exe icon
2 iSnetlheect"D"Erinvegrl"isfohld[UerninitethdeSCtDat-eRsO]"Mf.rom the
pull-down menu on the language selection
window and then click install button to start
installing.
installed software and places
Network Viewer 3 (File Converter 2) is installed in the
"Printers and Faxes" folder in the "Control Panel".
c
Network Viewer 3 (File Converter 2):
This is a kind of the printer driver to convert
to the JPEG data optimized to display by the
monitor from any of the documents created by
the application software.
* To uninstall Network Viewer 3(File Converter 2), just delete the "Network Viewer 3(File Converter 2)"
icon from the "Printers and faxes" folder.
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
3
Basic Setting and Operation
Describes basic operations and settings for controlling the monitor
by using the web browser. It is required that computer and monitor
is connected to the network and the network address is properly
configured.
29
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Login the setting page of the monitor
1 enter the iP address
Launch the web browser installed in your
computer, enter the IP address into the
"Address" on the browser and then press
"Enter" key.
Enter the address that you configured in
item "Network configuration" ( p.21).
The default IP address is [192.168.0.2].
2 select a display mode and login
This product provides 2 types of control mode, Standard Mode and Light Mode as the
below. Select a proper mode to match your PC and network environment by click-
ing on the text link. Once you select your desired display mode, the setting page you
selected display mode will be displayed automatically from the next login. To change
the display mode, click "Top" on lower-right corner of the setting page ( p.31).
STANDARD MODE
For computer display, displays
graphical menus and settings. This
mode is recommended for standard
use.
LIGHT MODE
Displays with 200 x 300 dots. This
mode is optimized for use of the
handheld computer, PDA, etc. It is
also convenient if the network traf-
fic is heavy. (This mode has some
limitations on the network viewer
and multi-control functions.)
If the setting page has set the password, the
authentication window will appear. In this case type
"user" onto the user Name text area and the login
Network PIN code onto the Password text area and
then click ok button.
* The entering User Name must be "user" and it can not be
changed.
[Note]
When accessing the monitor for the first time or the
Network PIN code "0000" is set, the auto-login will be per-
formed and the next main setting page is displayed.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Login the setting page of the monitor
3 Display of main setting page
The following main setting page will be displayed according to your display mode
selection. Perform various kinds of settings through this page. Click on the menus to dis-
play the control and setting pages.
1 Main setting page in the Standard Mode display
Clock display
Display on or off by
clicking text ON or
OFF
sub menu tab
Switches the sub
menu tab.
Page numbers
Switches the pages
by clicking the
number's tab.
Returns to Display
Mode selection
page ( p.30)
setting page
Main menu
For selection of control and
setting items of the monitor.
Displays the control and
setting items according to
the selected menu.
this standard mode display is mainly used through this manual for the setting and
control description.
If your computer does not have the Adobe
Flash Player version 6 or later, follow to the
message on the control page to install the
Adobe Flash Player. For further product
information or installing, see the Adobe
homepage.
http://www.adobe.com
ꢁ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
2 Main setting page in the Light Mode display
Sub menu tab
Page numbers
Returns to the display mode selec-
tion page.
Setting page
Main menu
The blank page appears if your PDA does not provide a
Adobe Flash Player. You need to install the Adobe Flash
Player. ( p.31)
the network viewer function in the Light mode has following limitation;
- Cannot select the program or folder for the display ( p.91, p.93)
- Cannot check up the images in the folder or program ( p.94).
How to use the setting page
To control and set up the monitor, use the setting menus on the web browser. Describes the
basic operation and procedures commonly used on this manual.
example of the setting Page
The setting pallet appears when clicking the item.
Change the value by clicking d or e button, or type
the number onto the text box directly and then click
set button.
* Each item has a valid setting range respectively.
Setting Pallet
The value in the text box indicates current value.
Each item has a valid setting range. The setting value exceeding this becomes invalid. Some con-
trol items can not be used depending on the selecting input mode or functions of the monitor
you use. In this case, the values of those items are indicated with "---".
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the setting page
type of the setting pallet
text box setting
Enter a number or text and
then click set button.
or
Change a value with d or e
button and then click set but-
ton.
The value changes quickly
when keeping pressing d or
e button.
Pull-down menu setting
Select an item with pull-down
menu button and then click
set button.
radio button setting
Select an item by selecting a
radio button.
Check box setting
Select items by ticking on
check boxes.
ꢁꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
initial setting
After installing this product to the monitor, perform the following basic ini-
tial setting.
Click initial setting on the main menu to display the initial setting page.
The model name of the monitor on which this product is mounted is displayed on the
page.
item
Description
Model name.......Indicates the model name of the monitor pro-
vided with the network unit
Network PIN code ......Sets the Network PIN code to login the setting
page ( p.35).
Temperature.......Switches display temperature unit Centigrade or
Fahrenheit.
!
Caution
use of Battery
This product provides a lithium battery. When the battery runs down, the clock and timer functions
do not operate properly. Contact your local dealer for the replacement of battery. The replacement
must be carried out by a qualified service personnel.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial setting
Network PiN code setting
This is to set the Network PIN code to restrict the access from
an unauthorized person through the network.
Enter a 4-digit number as the Network PIN code onto the text
box and click set button.
The network unit begins restarting and it takes about 20 sec-
onds. Close (Quit) the web browser and access to the login
page again in 20 seconds. This is to perform the login authentication firmly.
The default Network PIN code [0000] means no Network PIN code is set.
When you connect the monitor with this product to the network, it is recommended to set a new
Network PIN code. Only a four-digit number is valid for the Network PIN code.
Valid characters for the Network PIN code are only numbers 0 to 9. The number "0000" means no
Network PIN code is set.
This Network PIN code is not to restrict the use of the monitor. This Network PIN code is to set the
security against the use of the monitor through the network.
If you forget the Network PIN code to the monitor, you can initialize PIN code and IP Address/Sub
net/Gateway/DNS by selecting "Network initial" from "Installation mode" menu on the monitor.
For further information, please see instruction manual of the monitor.
ꢁꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
item
Description
Time setting........When clicking auto button, the date and time
set on your computer are set to the network unit
Current time.......Indicates current date and time set on the net-
work unit
Date..........................Sets date in manual
Time..........................Sets time in manual
Date and time setting
auto setting
Click auto button on the page, the date and time set on your computer are set to the
network unit.
Note:
Confirm that your computer has a correct clock time before performing the auto time setting.
Manual setting
Click item Date or time and enter date or time on the input box with adequate format.
Date is in year/month/day format.
ex. 2006/04/25
Time is in 24-hour:minute format.
ex. 18:30
ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Network configuration
Network configuration
Click Network on the main menu. The following setting page is displayed.
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server)
and monitor name are set up on this setting sub menu.
The IP address and Subnet Mask have been configured already in chapter "Installation".
If you want to change them or configure default gateway or DNS, perform them in this
page. If you change them, the network unit begins restarting and it takes about 20 sec-
onds. Close (Quit) the web browser and access to the login page again in 20 seconds.
item
Description
IP address.............Sets IP address of the monitor
Subnet mask.......Sets Subnet mask. Normally sets 255.255.255.0
1
Default gateway* .....Sets IP address of the default gateway (Router)
2
DNS* .......................Sets IP address of the DNS server. Must be set
when using the e-mail function
3
Monitor name* ...Sets name of the monitor. (64 characters maxi-
mum)
You must use the number specified by your administrator. The
address must be entered as a group with four numbers split by a
dot like [192.168.001.101].
*1 Set [0.0.0.0] if the network does not provide the gateway (router).
*2 Set [0.0.0.0] if you do not use the function E-mail alert.
*3 If you use the DNS server, register the host name registered to the DNS server as a monitor name.
You can access with this monitor name from any computers in your network. If you do not use
the DNS server, access with the assigned IP address to the monitor.
* All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.
ꢁ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
e-mail setting
This product has an E-mail function which can send an alert message to
users or an administrator if it detects an abnormality on the monitor. Click
e-mail setting on the main menu and follow the below steps.
item
Description
1
SMTP server* .....Sets server name or IP address of the SMTP server
Administrator
address...................Sets e-mail address of administrator
Add e-mail
address...................Sets e-mail address of the user to send mail when
the monitor has an abnormality.
1 Setting SMTP server and administrator address
1
Set the server name or IP address of the SMTP server* and administrator address. The
administrator address is set to "Reply-To" address of the message sent from the monitor.
*1 The SMTP server is a server for sending E-mail. Please contact your network administrator to
have this SMTP server address.
If the network unit sends an alert message due to the abnormality on the monitor but the SMTP
server is down in some other reason, the message will not be sent. In this case, the message
"Unable to connect to server." will be displayed on the setting page. To clear this message, set up
SMTP server address again.
To use the E-mail function, it must be set the DNS address on the Network setting page correctly.
You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your net-
work environment.
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail setting
2 Registering and deleting E-mail addresses
Click "Add e-mail address" and type the e-mail address
onto the text box and click set button. To check the
registered addresses, click Check/Delete sub menu tab.
The addresses are listed as the figure on the right.
Up to 10 E-mail addresses can be registered.
Check / Delete
To delete the registered addresses, check the address you
want to delete and click Delete button.
3 Option selection for sending alert mail
Click option sub menu tab. Check the condition items
under which alert mail will be sent and click set button.
Please refer to item "Examples :Type and contents of alert
mail" described on the next page.
[1]––––––––––––––––––––––––––––––––––
When power circuit is failed.
Option
When internal temperature is too high.
When internal fan circuit is failed.
When Panel usage time reaches [ ] hours.
[2]––––––––––––––––––––––––––––––––––
W
hen monitor is turned off.
When power save function turns Monitor off
When the signal is interrupted
When Auto Play is failed
.
.
.
If condition "When Auto Play is failed" is
checked, the trap is sent when occurring the
error during the auto display operation using
with the network viewer function ( p.92).
For further information of the error, refer to
item "Auto Display setting and control page
[3]"( p.95).
Up to 99,999 hours can be set for use time.
If condition "When monitor is turned off" is
checked, the trap is sent when the monitor
is turned off except Power/Fan fail, High
temp, Power save.
ꢁꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
examples: type and contents of alert mail
When the monitor has an abnormality, the following alert messages are sent to the regis-
tered E-mail address according to your selected condition. Administrator or user can take
an efficient action quickly by receiving this message. This is very useful to maintain and
service the monitor.
The following are examples of received messages.
c When power circuit is failed:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
* Error! Power circuit has failed.
The monitor was turned off, because the monitor power circuit failed.
Unplug the monitor from AC outlet and ask servicing to a qualified service personnel with
the error information.
c When internal temperature is too high:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
* Error! Internal temperature is too high, please check unit.
The monitor was turned off, because the monitor internal temperature rose too high.
Unplug the monitor from AC outlet and ask servicing to a qualified service personnel with
the error information.
c When internal fan circuit is failed:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
*Error! Internal fan circuit has failed, please check unit.
ꢂ0
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail setting
c When panel usage time reaches [ ] hours:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
*Information! Panel usage time has reached "****" hours.
The network unit sends this message when the panel usage time reaches the preseted
time.
c When power save function turns Monitor off:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
*Information! Power save function turns Monitor off.
c When the signal is interrupted:
TITLE: Message from monitor
10-03-2005 00:59
Monitor Model Name: model name
TCP/IP: 192.168.1.201 Monitor Name: Lcd05
It sends you following message.
*Information! The signal is interrupted.
ꢂ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
sNMP setting
This product provides a SNMP (Simple Network Management Protocol)
agent function. The SNMP consists of a manager and agents. The group
which communicates information each other with SNMP is called
"Community". There are two access modes in a community, Refer (read only) and Set (read-
write). This product allows to use Refer (read only) only. The SNMP message informs the
monitor status called "Trap" to an administrator. Click sNMP setting on the main menu and
set up each item.
Monitor information
item
Description
Contact.................Enter user name of the monitor etc. (optional)
Place .......................Enter place of the monitor (optional)
Community
name(refer).......Enter community name (read only). Default name
is "public".
The SNMP agent provided with this product is based upon MIB-2 defined by RFC1213. For private
MIB information, refer to file "Mibinfo/52LdNet.mib" in the CD-ROM.
ꢂꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP setting
Trap
item
Description
Community name......Enter community name to send "Trap". Default
name is "public".
Trap address.......Enter IP address of the SNMP manager computer
to receive "Trap".
Trap check/delete
Check and delete the trap address
Checking the registered trap address and deleting the
address.
To delete the address, tick check box in front of the IP
address and click Delete button.
Up to 10 trap addresses can be registered.
ꢂꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Trap option
trap option setting
Tick check boxes in front of the condition item to send the
trap.
Click set button if you tick or un-tick the check box on a page.
[1]––––––––––––––––––––––––––––––––––
When power circuit is failed.
When internal temperature is too high.
When internal fan circuit is failed.
When Panel usage time reaches [ ] hours.
[2]––––––––––––––––––––––––––––––––––
W
hen monitor is turned off.
When power save function turns Monitor off
When the signal is interrupted
When Auto Play is failed
.
.
.
Up to 99,999 hours can be set for the time setting.
If condition "
W
hen Auto Play is failed" is checked, the trap is sent when occurring the error during the
auto display operation using with the network viewer function ( p.92). For further information of the
error, refer to item "Auto Display setting and control page [3]"( p.95).
ꢂꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
Power control and status check
Click Power & status on the main menu. The control page will be dis-
played.
By clicking oN or standby button on the page, the power of the monitor can be con-
trolled.
Confirmation window
as shown in the below
appears when the
standby button is pressed.
Popup confirmation window
item
Description
Monitor status
Power .........................Displays the status of the monitor. (ON, OFF)
Status ..........................Displays the status of the monitor's power.
Power control........Controls the monitor power by clicking the "ON" or "Standby" button.
Monitor temperature
Inside temperature ....Displays the internal temperature of the monitor.
* The temperature unit can be set either Centigrade or Fahrenheit in item "Initial
setting". ( p.34)
ꢂꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Power control and status check
ꢂ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
Controls
Click Control on the main menu. The setting method differs depending on the contents
of the page. Click on the page number to change pages and select desired setting items.
Please see the instruction manual of the monitor to have the further information
of each control item.
input
This function is to select the input mode and source mode of the monitor. Click set but-
ton after selecting the input and source mode.
item
Description
Input.......................Selects input mode of the monitor.
AV 1
RGB
AV 2
AV 3
PC
DVI
NETWORK
Source.....................Selects signal source of the input.
AV 2 : YPbPr/RGBHV
The control page displays valid control items depending on the selected input mode, signal ,
therefore, there may be different controls between the described items and actual control items
on the page display. For further information , refer to the monitor's owner's manual.
When the monitor is in standby, only the timer on the setting menu is effective; others are inactive.
ꢂꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
Picture adjustment
This function is to adjust the displayed picture image.
item
Description
Contrast.................Adjusts picture contrast
Brightness............Adjusts picture brightness
Color.........................Adjusts picture color saturation
Tint............................Adjusts picture hue
Sharpness.............Adjusts picture sharpness.
item
Description
White Tone...........Sets a white tone mode. ( Cool, Standard, Warm,
Personal)
Picture Mode......Sets a picture mode. (Standard, Dynamic, Soft, Eco,
Personal)
item
Description
DCDi............................Switches DCDi (Directional Correlational
Deinterlacing) mode. (Off, On)
ACC/ACM............Switches ACC/ACM (ACC: Adaptive Contrast
and Color; ACM-II: Active Color Management-II)
mode. (Off, Vivid, Cinema, Sport)
CCS.........................Switches CCS (Cross Color Separation) mode. (Off,
Auto, Standard)
DNR........................Switches DNR (Digital Noise Reduction) mode.
(Off, Auto, Low, Mid, High)
MPEG NR..................Switches MPEG NR (MPEG Noise Reduction)
mode. (Off, On)
Film mode...............Switches Film mode (Inverse 3:2 pulldown):
mode. (Off, On)
ꢂꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
sound
This function is to adjust the sound of the monitor. The values in the text box represent
the current control value or status.
item
Description
Volume...................Adjusts the sound volume.
Mute.........................Suppresses the sound. (ON, OFF)
ꢃ0
Download from Www.Somanuals.com. All Manuals Search And Download.
PC adjustment
PC adjustment
Click PC adj. on the main menu. This function is to adjust the signal from
the computer connected to the monitor to obtain the proper picture
image on the screen.
item
Description
Auto PC adj............Performs automatic adjustment.
H-Position.............Adjusts the horizontal position of the screen.
V-Position.............Adjusts the vertical position of the screen.
Clock ........................Eliminates flicker from the image.
Phase...........................Eliminates disorder from the image.
ꢃ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
setting up the monitor
Click setting on the main menu. This function is to set up the monitor.
Select the sub menu [Screen setting], [Setting] or [Tile Mode] and then set
up each setting.
item
Description
Wide ........................Switches the screen mode. (Full, Zoom16:9,
Title16:9, Zoom14:9, Title14:9, Normal, Natural)
There may not be available mode depending on
the input mode.
ꢃꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Monitor
item
Description
Freeze.....................Sets the image to freeze mode.(ON, OFF)
Child lock.............Sets child lock mode. (ON, OFF)
RC Inhibition......Sets remote control inhibition mode. (ON, OFF)
Initial setting.........Sets all of the monitor control items to the fac-
tory default setting except for Installation mode .
* This function is not effective for the settings
of the network unit (Network address settings,
e-mail settings, etc.)
ꢃꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
item
Description
Tile Mode Active...Sets tile mode active. (Off, On)
H-Sets........................Sets to divide the horizontal picture.
V-Sets.........................Sets to divide the vertical picture.
H-Location...............Select one part of the horizontal picture.
V-Location...............Select one part of the vertical picture.
Bezel H Adjustment..Adjusts the horizontal picture for smooth image.
BezelV Adjustment...Adjusts the vertical picture for smooth image.
refer to the monitor's instruction manual for operation of the tile mode.
ꢃꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Setting
timer setting
This page is to set the timer to turn the monitor off or on at a programmed
day/date and time. Follow the steps below for setting.
Click timer on the main menu.
Present time set on the
network unit
Select date
Select day
Set execute time
Event
action
How to set the timer
1 Set a day or date
to set the timer event at same time everyday or every week,
Select day entry with radio button and then select desired day with the pull-down menu
button.
The selectable days are as follows:
- same time everyday
- every week ( days from Monday to sunday)
to set the timer event on specified date,
select date entry with radio button and then type the date with (Year/Month/Date) for-
mat.
ex.: type [2005/12/20] if you specify [December 20, 2005].
ꢃꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
2 Set an execute time
Type the time with (Hour:Minute) and 24 hours format.
ex.: type [18:25] if you specify [PM 6 o’clock and 25 minutes].
3 Select an event action
Select an event action from the pull-down menu.
event
action
ON..................................Turns on the monitor
OFF................................Turns off the monitor
*Available events depends on the monitor function.
4 Register an event
Click set button to register the set timer event. Repeat steps 1 to 4 for another timer
event setting.
Check the timer events
To check the set timer events, click Check button. The timer
events are listed. The event with blue background color rep-
resents the timer-OFF event.
Change the event mode
On the event list appearing by clicking Check button, click
on the event you want to delete, disable or enable. Click
Cancel, Delete, timer oN or timer oFF button on the
popup pallet.
Button
operation
Cancel......................Cancels the setting
Delete......................Deletes the timer event
Timer OFF.............Disable the timer event temporarily
Timer ON...............Enable the timer event
ꢃꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer setting
Notes on timer setting
Up to 10 timer events can be registered. Timer events always operate according to the next valid
event depending on the monitor's power status. In the example below, event 3 turns on the moni-
tor so next event 4 (also turning on monitor) will not be effective because the monitor is already
turned on. Similarly, when the monitor is turned off by event 5, event 6 OFF will not be effective
in turning it off again. But these secondary events (event 4 and event 6) will become effective if a
person turns off the monitor (after event 3 and before event 4) or turns on the monitor (after event
5 and before event 6).
Invalid event
Invalid event
OFF
OFF
ON
OFF
ON
Monitor
Event 1
Event 2
Event 3
Event 4
Event 5
Event 6
ON
OFF
ON
ON
OFF
OFF
Time
When the timer events are set at the same time, the last event set will override the previous
events. For example, if there is an event like "ON at 8:00 everyday" and then new event is set like
"OFF at 8:00 everyday", only the last setting event is effective.
The timer operates by using the clock function provided in this product. Before setting the timer,
please confirm that the current date and time are set correctly. Timer and clock functions are func-
tioning using a lithium battery provided in this product. When the battery runs down, the clock
and timer functions will not operate correctly. Consult your local dealer for the replacement of bat-
tery. The replacement must be carried out by a qualified service personnel.
ꢃ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
Monitor information
This page is to display the basic information of the monitor status. Click
information on the main menu.
items
Description
Input.........................Displays selected input and source.
System....................Displays selected signal system.
Signal.......................Input signal status (Yes, No)
Wide.........................Displays screen mode.
Panel time..............Displays the panel use time.
Timer........................Displays the timer status (ON, OFF)
Click this button to
update the information
ꢃꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
Multi-control
Controlling and setting the multi-monitors
This function enables you to control the multiple monitors equipped with
the network units that are connected to the network. Click Multi Control on the main
menu to display the control page.
Note:
to control the multiple monitors, each monitor must have the same Network PiN code.
example of multi control
MONITOR 1
MONITOR 2
MONITOR 3
MONITOR 4
PC6
PC5
PC4
Select Input2 for
MONITOR 1 to
MONITOR4.
ꢃꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
start/stop the multi control
To start or stop controlling the multi-monitors, click
Multi control setting menu and select ON or OFF.
Switches on and off the
multi-control function
Multi control setting
OFF........Stops multi control function
ON..........Starts multi control function. The multi control
menu will appear when setting ON. These
items of menu are linked to the main menu.
The multi controllable menus are "Power & Status", "PC
adjustment", "Control", "Setting", "E-mail setting", "Timer",
"SNMP setting" and "Network Viewer". Click each menu
and perform setting and adjustment.
The word "MULTI CONTROL" appears on the each control
page while the multi control is operating.
This shows the multi con-
trol is operating now.
ꢄ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
register the monitor
To use the multi control function, register the IP address of the monitor you intend to con-
trol. Click registration sub menu tab and set the IP address, Memo and Multi control item,
then click set button.
items
Description
IP address............Enter IP address of the monitor to control
Memo.....................Enter monitor name or installed location etc.
Multi control item
Control.............. Controlling the monitor
Both control .. Controlling and displaying images
Visual control .... Displaying the images
Confirmation of registered monitor
To check the registered information, click Check & Change
sub menu tab. The registered information of the monitor is
listed as the below.
* When you click on a listed IP
address, the login page for the
selected monitor will be displayed
with a new window.
* The word "none" is displayed if not using the "Memo" func-
tion.
IP address
Status
Memo
Page no.
Click here to close
the sub menu Check
& Change.
10 monitors per page can be registered and up to 100 sets can be registered for the multi-control.
ꢄ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
Change the mode of the registered monitor
To change the mode of the registered monitor, select a mode with the pull-down menu
button under the IP address of the target monitor and then click set button.
Mode
operation
Control.................... Controlling the monitor
Both control........ Controlling and displaying pictures
Visual control.......... Displaying the pictures
OFF............................ Excluding from the multi-control
Delete...................... Deleting from the multi-control
* The multi control item is not changed during using the
network viewer function. It is not available with the light
mode.
status
If some of the registered monitors are disabled by some
reasons (such as disconnecting the power source, dis-
connecting the LAN cable, disconnecting from the net-
work), control changes will continue to be effective for
the monitors that are still active. At the same time, the
deactivated monitors are excluded from the multi-con-
trol. The status of the registered monitors are indicated
under the monitor name. See the table below for status
indications.
Status
status
Description
(blank).....................The monitor is connected to the network correctly
No connect..........The monitor may not be connected to the network. Please check the connection
and network configuration of this monitor.
PIN code error.............The PIN code is incorrect. The PIN code for the multi-controlled monitors must be
the same. Change the PIN code of this monitor to the common PIN code.
File Error................. Not displaying the images. Check if this monitor is using the Network Capture func-
tion or Network Viewer function individually, or in the standby mode.
* The network unit updates the status at the time when the multi-control function was executed.
If the multi-controlled monitor is in the standby mode, any change is not effective except timer
setting.
Cannot register, delete or change the multi-control setting during using the network viewer func-
tion.
It is recommended that a specified monitor should be chosen for setting as a master when you
use this multi-control function. The control for the multi-controlled monitors will become too
complicated operation if this function is used for each monitor.
If the registered monitor is not connected to the network, it will take some time to complete the
multi-control operation because of waiting for the response from each registered monitor.
There are some disabled items in the multi-control function for the light mode.
ꢄꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
Check & Change page in the light mode
Following functions in the "Check & Change" page are
not available in the light mode.
- Changing the control mode.
- Deleting the registered IP address
- Indicating the each status
- Indicating the each memo
This indicates that the
mode is "VisualControl".
This indicates that the
mode is "Control".
Connection status
Blinking: Connected
Gray: Disconnected
(Check & Change page in the light mode)
Controlling all together
"Power & Status", "PC adjustment", "Control" and "Setting"
can be controlled all together. Set "ON" the multi control
setting and adjust controls of each menu. The setting
value is applied to the registered monitors sequentially .
This is effective only if the multi control item of the regis-
tered monitor sets to either "Control&Image" or "Control".
setting all together
"E-mail setting", "SNMP setting" and "Timer" can be set all
together. Set "ON" the multi control setting and items of
each menu. The setting value is applied to the registered
monitors sequentially.
This is effective only if the multi control item of the registered
monitor sets to either "Control&Image" or "Control".
ꢄꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Monitor
Multi-control
Viewer auto setting all together
"Viewer auto display" can be set all together. Set "ON" the
multi control setting and select [3] auto display setting
from Viewer sub menu (selected by "Multi-control" -
"Network Viewer" menu). Set the display time periods and
repeat times for the auto image display. When clicking
start button, the registered monitors start playing back
the auto image display in sequential.
For further information of the Auto display, see "Using the
network viewer function". ( p.92)
This is effective only if the multi control item of the registered
monitor sets to either "Control&Image" or "Image".
ꢄꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
about Network Capture function
The Network Capture is a function to display the screen images of the computer which
has a Network Capture 3 software by the monitor through the network. This function has
2 kinds of mode as the below.
- Real Time Capture ( p.68)
A function to display the screen image of the computer by the monitor through the
network in real time.
- Network Communication ( p.ꢀ1)
This mode is to communicate by sharing the capture image of a computer with multiple
computers and a monitor. User can draw the text and figure on the captured image by
using a drawing tool.
Up to 30 computers can be registered.
The Network Capture function cannot be used when using the Network Viewer function. The
Real Time Capture and Network Communication mode cannot be used at the same time.
Launching the Network Capture 3
After installing the Network Capture 3 software, the shortcut icon is copied into the
"Startup" folder. When you boot the computer, the Network Capture software also starts
and its icon stays on the task bar. If the icon is not appeared on the task bar, the Network
Capture 3 software is not starting. Click "Network Capture 3" from "Start" - "All the
Programs" - "Network Viewer & Capture 3" menu to launch it manually. The status which
the Network Capture 3 icon stays on the task bar is just preparing the screen capturing.
Commands on the task bar
When clicking the Network Viewer & Capture 3 icon
on the task bar, The popup menu will appear as the
right. See the next page for each operation.
ꢄꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
About Network Capture function
items
Description
Start real time capture..................Starts the real time capturing. ( p.68) The screen image of the computer is
displayed on the monitor in real time.
Start communication ....................Starts the Network Communication. ( p.71) Captured image is displayed
on the monitor. The captured image edit window appears on the computer
screen.
Parameter set up............................Sets the communication parameter between the computer and network
unit of the monitor. For further information, see item "Parameter set up"
below.
Version information.......................Displays the version of this software.
Shut down ......................................Quits the application.
Parameter set up
1 Click Network Capture 3 icon on the task bar.
2 Click "Parameter set up" on the popup menu. The set-
ting window will appear.
3 Set Capture Port and PiN code to match to the
monitor’s port number and Network PIN code.
To check the Capture Port number, see item "Control by
the web browser" ( p.70). To check the PIN code, see
item "Network PIN code setting" ( p.35).
Specify the port number of TCP/IP. The default port set-
ting is 9000. There are some reserved port numbers and
also some applications may use their own port numbers.
If one of those port numbers is used, the alert dialog
window will appear and let you know that it is an invalid
port number. In this case, use another port number.
The reserved port numbers are http (80), ftp (21), telnet
(23), etc. The port no. 4352, 10000, 10001 are reserved to
control the monitor through the LAN port.
4 Click search button to list up the available IP address
assigned to the monitor and select desired IP address you use, or you can enter the IP
address or host name manually if you know that IP address or host name.
It may not find any address over the router. Consult your network administrator for further
details.
5 Set the quality of the image.
Quality: Selects from High, Mid, Low
Image Scaling: If checked, the screen image size of the computer is automatically adjusted to the
monitor’s screen size.
6 Set capture start time in second unit.
This is effective in the communication mode only. It sets up the time period from executing
the command "Capture transfer" to capturing and transferring the actual screen image. 0 to 60
seconds can be set.
7 Click ok button to close the setting window.
about image Quality
Quality : Quality mode of the captured image shows following JPEG compression mode.;
High
Medium : JPEG medium compression mode
Low : JPEG high compression mode
: JPEG low compression mode
ꢄ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
using the real time Capture
This is a function to display the screen image of the computer by the monitor in real time.
The captured image displayed by the monitor can be selected from the computer, web
browser and the monitor respectively.
registering the computers
Up to 30 computers can be registered.
1 Access to the control page of the monitor by using the
web browser. From the Network menu, click Capture
p.37).
2 tSawbittcohditsoplCayonthneescettitoinngspeatgtein(g page by clicking the
page number tab [3]. Enter the IP address of the com-
puter to the PC number, and then click set button. Click
set button to register the IP address for each page.
The registered computer enables to start capturing if only the Network Capture icon appears on
the task bar.
The transfer speed of the captured image using the Real Time Capture function is depending on
the network environment and data volume of the image. For example, when transferring an image
(Computer resolutions and colors: XGA, full color, Picture quality: High), the transfer speed is about
2 pages per second in maximum. It cannot be supported for movie pictures.
The mouse pointer on the computer's screen cannot be captured.
ꢄꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Real Time Capture
[1] Control by the computer
* PC provides the Network Capture.
Project this screen
MONITOR 2
MONITOR 1
PC1
imagewith MONITOR 2.
Capture
PC3
PC4
PC6
* Start capturing from
the PC1.
PC5
Select input mode to "Network" previously.
1 Click Network Capture 3 icon on the task bar.
2 Click start real time capture on the popup menu.
The screen image of the computer will appear on the
monitor display in real time.
• To stop capturing, click stop real time capture on
the popup menu. The captured image of the com-
puter on the screen is frozen.
icon on the task bar
• To restart capturing, click restart real time capture
on the popup menu.
3 To end capturing, click end real time capture on the
popup menu.
standby
Capturing
If the Network PIN code set on the monitor differs
from PIN code set on the parameter setting up,
The Pin code setting window appears. Enter a cor-
rect PIN code and click ok button.
If the error message appears, check item "Parameter set up" ( p.67).
ꢄꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
[2] Control by the web browser
* PC provides the Network Capture.
MONITOR 2
MONITOR 1
PC1
PC2
Capture
* Start capturing of
the PC1 from the
PC5.
PC3
PC4
PC6
PC5
Project a screen
image of PC1 with
PC2.
Select input mode to "Network" previously.
1 Access to the control page of the monitor by using the
web browser. From the Network menu, click Capture
2 tSaebletoctdtishpelacyothmepsuettteinr gnupamgbee(r from the pull-down
p.37).
menu button of "Connecting PC" and click start but-
ton. The screen image of the selected computer will
appear on the monitor display in real time.
• To stop capturing, click stop button. The captured
image of the computer on the monitor is frozen.
3 •ToToernedstcaarpt tcuarpintugr,inclgic,kcleicnkdrbeustttaornt.button.
Set "On" when
using the wireless
mouse function
The IP address of the connecting PC should be registered previously ( p.68).
If the error message appears, check item "Parameter set up" ( p.67).
You can use the capture function by using the web browser or the monitor if the Network
Capture 3 software is installed into the computer correctly and its icon stays on the task bar.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Communication
using the Network Communication
This Network Communication is to communicate by sharing the captured image of a com-
puter with multiple computers and a monitor. User can draw the text and figure on the
captured image by using a drawing tool.
The data that has the captured image of a Main PC and communication information is sent
to the monitor. The monitor displays this data onto the screen and serves this data to other
computers (Sub PC) at the same time. The Sub PC receives served capture data and dis-
plays it on the screen. The Main PC and Sub PC also can edit the captured image by using
the drawing tool. This edited image is applied to all the computers automatically.
MONITOR 1
Capture
PC6
PC1
PC2
PC5
Capture a screen
image of PC5 and
make marking with a
tool.
* The Main PC is a computer which started using of communication function, and serves
own computer screen captured image to the Sub PC. The Main PC has an authority to
quit using whole of communication. To become the Main PC, execute the command
"Start Communication" or "Capture transfer". For further information, see item "How to
use the Network Communication". ( p.75)
* The Sub PC is a computer which receives a captured image from the Main PC. On the
communication mode, the Sub PC can become the Main PC anytime.
71
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
settings before using the Network Communication
To use the Network Communication, the capture setting of the network should be set
either [1] or [2] described below.
[1] setting the network unit searches all the available target computers in the net-
work automatically.
or
[2] setting the target computers are registered to the network unit.
Perform capture setting following to the description below.
[1] When serving the capture data to all the tar-
get computers in the network.
By using the web browser, display "Communication set-
ting" from menu "Network"-"Capture"-"Page 2". Confirm
that the item Auto search target PC is "ON". If "OFF",
change mode to "ON".
* Network unit can find up to 30 computers in the network.
[2] When serving the capture data to the specific
target computers in the network.
Set item Auto search target PC is "OFF" described in
the above and then display "Connection setting" from
menu "Network"-"Capture"-"Page 3" with the web
browser. Enter the IP address of target computer and
click set button to register.
* Up to 30 computers can be registered to the network unit.
To display the served capture data, the computer needs to operate the software Network Capture 3.
7ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Communication
Description of capture editing window
Select menu "Start Communication" from the popup menu appearing by clicking the
Network Capture 3 icon on the task bar. The capture editing window will appear on the
computer screen as the below. For basic operation of each menu, refer to the item "Menu
tree" below.
Menu
Tool bar
Capture Image
Authority status
indication frame
(
.p75)
Menu tree
Menu
submenu
operation
File
Save Communication
Saves a captured editing image as the data(JPEG)
Save dialog window appears
Quit the communication mode
Close the Editing window
* main pc only
End Communication
* sub pc only
End Editing
Control
Capture transfer
Authority
Captures a screen image and sends it to the network unit
Acquire/release the authority to edit the capture image
Selects a pencil tool
edit
Tool
Pencil
Eraser
Selects an eraser tool
Letter frame
Free
Straight line
Square
Selects a letter frame tool
Draws line with freehand
Draws straight line
Draws square
Form
(Shape)
Oval
Draws oval
Square(Painting out) Draws filled square
Oval(Painting out) Draws filled oval
Attribute
Delete all
Undo
Appears a attribute window
Delete all the drawings on the image
Cancel the last executed operation
Display
Help
Full screen
Tool bar
Switches capture editing window, normal or full screen
Switches standard tool buttons on or off
Switches form(Shape) tool buttons on or off
Switches color tool buttons on r off
Switches attribute tool buttons on or off
Keeps capture editing window on foreground always
Displays software version number
Standard
Form(shape)
Color
Attribute
Display on foreground
Version information
7ꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
tool bar button names
The following commands are assigned to the tool bar buttons. For each operation, refer to
the description of item "Menu tree".
Command tool
Bar of Main PC communication
Save
End communication
Capture
transfer
Authority
Attribute
standard
tool bar
Form
tool bar
Oval(Painting out)
Square(Painting out)
Pencil
Letter
frame
Straight line
Eraser
Free
Oval
Square
Command tool
Bar of sub PC
End Editing
Color pallet 16 colors
Color tool
bar
attribute
tool bar
Width (Large,
Medium, Small)
Translucence
To switch the tool bars displaying on or off, select each command from menu "Display"-"Tool bar".
User can realign and join the tool bars (Standard, Shape, Color, Attribute), and change it to the
floating pallet by taking a drag and drop of the tool bars.
There are some disable buttons depending on the tools and authority mode. In this case the but-
ton indicates with gray.
7ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Network Communication
How to use the Network Communication
start the communication
1 Display an image on the computer screen.
2 Select start Communication from the popup menu appeared
by clicking Network Capture 3 icon on the task bar.
The capture editing window with a captured image appears
on the computer screen.
If an error message appears, check item "Parameter set up". ( p.67)
icon on the task bar
The icon on the task bar is activated during the network communica-
tion operates.
standby Communication
Join the communication (only for Sub PC)
1 Network Capture 3 icon is activated to inform users in the net-
work that the Network Communication is operating. Display
2 Stheelepcot psutaprmt eedniutibnygcmlicekninug. its icon.
The capture editing window with
a captured image appears on the computer screen.
exit from the communication (only for Sub PC)
Click "
:End editing" button on the standard tool bar. The capture editing window will be
closed.
This command is available with the Sub PC only.
When executing "End editing" with the authority provided, the authority will be released.
end the communication
Click " :End communication" button on the standard tool bar.
The capture editing window will be closed.
This command is available with the Main PC only.
It cannot be ended the communication while other PC has the authority. To end communica-
tion forcibly, click the Capture 3 icon on the task bar and select "Shut down" on the popup
menu.
acquire and release of editing authority
To edit the capture image, each computer needs to acquire the authority respectively. To
acquire the authority, click " : Authority" button on the standard tool bar and then edit
the capture image. The capture editing window indicates the authority status by changing
the frame color according to the current authority mode as follows.
Red
Blue
ready to acquire an authority
Green
other computer having
an authority
having an authority
7ꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
edit capture image
Drawing figures
1 Click " :Pencil" button on the form tool bar.
2 Select its attribute (shape, width, color and translucence) from the form and attribute
3 tDoroalgbaarm. ouse pointer on the screen image to draw the figure.
Erase drawn object
1 Click " :Eraser" button on the form tool bar.
2 Select its attribute (shape, width) from the form and attribute tool bar.
3 Drag a mouse pointer on the screen image to erase the figure.
Hints of the drawing
Straight line tool............ To draw the vertical line or horizontal line, drag a mouse pointer with shift
key pressed.
Square tool........................ To draw the quadrate rectangle, drag a mouse pointer with shift key
pressed.
Oval tool............................. To draw the perfect circle, drag a mouse pointer with shift key pressed.
To cancel the drawing, select command "Edit"-"Undo" from the menu.
To erase all the drawing at once, select command "Edit"-"Delete all" from the menu.
The popup menu appeared by right clicking of the mouse is also available to select the tool and
change the attribute.
Setting of the drawing tool attribute
When clicking " :Attribute" button on the standard tool bar, the following window will
appear. This window appears only if the pencil or eraser tool is selected.
Line width
Large: 8 dots
Medium: 4 dots
Small: 2 dots
Select a color on the
color pallet appeared
by clicking here.
Sets translucent
color
7ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Network Communication
Drawing letter
1 Click " :Letter frame" button on the form
2 tSoeolelcbtaar.color of text with color tool bar.
3 Drag a mouse pointer on the screen image to
specify the area of the letter frame. The letter
4 Einnpteurt tdhiaelolegttwerinodnotowthweillwaipnpdeoawr..
To change the letter attribute, click Letter
attribute button. See item "letter attribute
5 sCeltitcinkgo" bkeblouwt.ton to fix the content. The
entered letter appears on the captured image.
If the entered letter overflows the area of letter frame, the letter frame is automatically extended
downward.
Up to 1000 characters can be used for a letter frame.
Letter attribute setting
The font attribute setting window appears when clicking " :Attribute" button on the
standard tool bar with the letter frame tool selected, or clicking Letter attribute button
on the letter input dialog window described the above.
Sets type face, style, size and
effects of the font
Predefined 16 col-
ors are available.
Sets translucent
color
77
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Network Communication operation and change of state
Network Communication can be used under the environment which one or more com-
puters are connected to the monitor via the network.
Preparation
Launch the Network Capture 3 software on the target computer ( p.66). Set the monitor
in the standby or turning on. Check IP address of the target computer is registered in the
connection list ( p.72).
Operation on the Main PC
Operation on the Sub PC
The icon on the task bar is activated to
let users know that the captured image is
now serving.
1 Executing the command "Start Editing".
The capture image on the Main PC
appears on the screen.
Frame
Frame
1
Executing the command "Start Communication".
The capture editing window appears on the
screen. The icon on the task bar is activated.
r
B
2
Editing the capture image using with the tools.
The editing information on the Main PC is
The editing information is automatically
r
G
B
B
G
r
reflected on the Sub PC.
transferred to the Sub PC.
The color of authority status frame chang-
es green.
3 Releasing the editing authority.
The color of authority status frame changes green.
2 Acquiring the authority.
The color of authority status frame chang-
es red.
The color of authority status frame changes blue.
3 Editing the captured image using with the
The editing information on the Sub PC is
reflected on the Main PC.
tools.
B
r
The editing information is automatically
transferred to the target PC.
4 Releasing the editing authority.
The color of authority status frame chang-
es green.
The color of authority status frame changes green.
G
G
B
The color of authority status frame chang-
es blue.
4 Acquiring the authority.
r
The color of authority status frame changes red.
5 Repeat steps 2, 3 if required.
5 Repeat steps 2 to 4 if required.
6
Executing the command "Capture transfer".
A new captured screen image appears on
Updating the editing window with a new
r
r
B
the editing window.
captured screen image.
7 Repeat steps 2 to 5.
8 Ending the communication.
The capture editing window disappears.
The capture editing window disappears.
The monitor displays the edited captured image on the screen when the input mode of the moni-
tor is set "Network".
The command "Save Communication" can be executed in any of the mode even if not having the
authority.
The arrow () shows a response to the command executed.
The execution of the command "End Communication" or "End Editing" on the Sub PC has no
effect on the other target computers.
7ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Executing the forcing mode
executing the forcing mode
The network capture setting of the web page provides a forcing executing command. This
command executes the release of authority or ending the communication forcibly. This is
useful when the other target PC keeps an authority all the time, or when the condition of
the communication is not stable.
Click page 2 Communication setting from the menu "Network"-"Capture". Execute com-
mand by clicking the button Free, Quit or update.
Displays IP address of the Main PC
Displays IP address of the computer
has a editing authority
item
Free...........................Releases the editing authority forcibly
Sets condition which all the users can acquire an authority
Quit...........................Quits the communication forcibly
The capture editing window on all the computers closes forcibly.
Update....................Acquires the latest communication status
Updates the IP address of the Main PC and Update authorized PC.
Description
7ꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Network capture function is for projector originally. So some error
messages include word "PJ". Here "PJ" means "Monitor".
error information
error messages
Cause and corresponding
Error when executing the communication. The parameter setting
(host name, capture port) has not been set.
Check parameter setting ( p.67)
Set up the parameter.
Error when executing Start Communication or Start real time cap-
ture. The IP address of the computer has not been registered.
Register the IP address by using the web browser ( p.72)
It has not been registered to
monitor as a group.
Error when executing Start Communication or Start real time cap-
ture. The other capture, viewer or advanced card imager function
is now operating.
Cannot be displayed as moni-
tor is under display.
Wait until the communication function is available.
Cannot establish the connection with the network unit when
executing the Start communication, End communication, Capture
transfer, Start real time capture or End real time capture.
Cannot connect to monitor.
Check connection of the network cable.
Cannot transfer the data to the network unit when executing the
Start Communication, End Communication, Capture transfer, Start
real time capture or End real time capture. The time out period is
10 seconds.
Cannot transfer data to moni-
tor.
Check connection of the network cable.
Cannot receive the data from the network unit when executing
the Start Communication, End Communication, Capture transfer,
Start real time capture or End real time capture. The time out
period is 10 seconds.
Cannot receive data from mon-
itor.
Check connection of the network cable.
Other PC has authority.
Cannot complete "Network
Communication".
When executing the End communication, you cannot quit the
communication because other computer has an authority
Other PC has authority. Cannot
obtain authority.
Other computer has an authority.
When setting the parameter, the computer cannot find the set-
ting host name or IP address in the network.
Use available host name or IP address.
The server name or address
could nt be resolved.
When setting the parameter, the reserved port number is speci-
fied.
Check parameter setting ( p.67)
Invalid port number
Monitor has not started Network
Communication. Close the window
and open it again.
The monitor might have turned off during the communication.
Check monitor power and restart executing "Start communication".
ꢅ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
6
Network Viewer
Network Viewer is a function to display the image data stored in
the file servers by the monitor through the network.
Describes about file converter software File Converter 1, File
Converter 2 and program creator software Program Editor, and
how to use Network Viewer.
81
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
Creating the available data [Network Viewer 3]
The image available with this monitor is the JPEG format (.jpg). There are several types of
JPEG data. Before using the images with the Network Viewer function, it should be con-
verted to the optimized JPEG data for this monitor.
[1] How to use the Network Viewer 3 (File Converter 1)
The File Converter 1 is a software to convert from the JPEG, bitmap or Power Point data to
the optimized JPEG data for the monitor.
Launch and quit the File
Converter 1
To launch the File Converter 1, click
"Network Viewer 3 (File Converter 1)"
menu from "Start" - "All Programs" -
"Network Viewer & Capture 3" menu.
To quit the File Converter 1, click
on the close box on the upper
right hand of the window.
File Converter 1 window
Menu
Command
Tool Button
Preview window
Explorer window
to browse image
files
ꢅꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating the available data [Network Viewer 3]
Menu tree
Menu
sub Menu
Description
View
Update
Preview size
Option
Convert a folder
Convert each file
Version information
Updates contents of the preview window
Sets size of the preview image, Large, Middle, Small
Sets default of the output destination and conversion mode
Converts files in a folder into JPEG files at once.
Converts a file into a JPEG file individually
tools
Conversion
Help
Displays the version information
Command tool Button
Convert
each file
Convert a
folder
Update
Create the available data
1 Select a folder in which the image files are stored by the explorer window.
The preview images of the available image data (JPEG file, Bitmap file, power point file)
in the selected folder are displayed on the preview window.
On the preview window, the preview displayed with the red frame represents a file not opti-
mized JPEG file or Bitmap file for the display. The preview without the red frame represents
the optimized JPEG file for the display. So you do not need to convert them again, but if you
change the size or image quality, perform to convert them again.
Preview with red frame
represents the file not
optimized for the dis-
play.
Preview of the Power
Point data
ꢅꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
2 When converting each file, select a preview
image first and then click Convert each file.
To select two or more files at once, press and hold
"Shift" key or "Ctrl" key and then click the preview images.
When converting all the files in a folder, select a folder and click Convert a folder.
3 As the confirmation window appears, check the conversion object and conversion
type and then click ok button. The File converter 1 starts converting and stores the
optimized files into the output folder. It enables you to select a local hard disk of your
computer, shared computer in the network, a directory of the FTP server. To change the
conversion type or output destination, click Change button.
If the power point file is included in the conversion object, the Microsoft Power Point software
will be launched and start converting automatically.
Dialog window when using "Convert
each file" and "Convert a folder"
To convert images from the power point file, Microsoft Power Point software is required in your
computer.
In the power point file conversion, all the pages are converted into JPEG files separately.
ꢅꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating the available data [Network Viewer 3]
setting of output destination and conversion mode
When clicking Change button on the confirma-
tion window in the step 3 on the previous page,
following option setting window appears.
output destination
Select either Folder or FtP server as the output
destination of the converted files.
Folder
Output folder.....Specify a folder in the local hard disk
or shared computer in the network
FTP server
Host name............Enter host name or IP address of the
FTP server
Root Folder..........Specify the root directory of the FTP
server. Normally use "/".
User ID ....................Enter your login account of the FTP
sever.
Password...............Enter your password of the FTP server.
Output folder.....Specify a directory of the FTP server.
Conversion mode
Resolution............Selects output image resolution (VGA to SXGA+)
The image resolution higher than the monitor's panel resolution cannot be dis-
played.
Image rotation.....Selects image rotation (0, 90, 180, 270).
Conversion Type
Fit............................. Converts as either width or height of
the image sets to be the maximum
screen width or height.
Justify
[both ends]............... Converts as width of the image sets
to be the maximum screen width.
Justify
[top and bottom]..... Converts as height of the image sets
to be the maximum screen height.
Cut........................... Cuts image with the screen size not depending on the image size. This type has fol-
lowing mode.
Select this mode when you want to have the images with the original size. Select
each mode by clicking on the button.
Image Quality....Selects an image conversion quality with "High", "Mid" or "Low".
ꢅꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
[2] How to use the Network Viewer 3 (File Converter 2)
The File Converter 2 is a kind of the printer driver software to convert to the optimized
JPEG data for the display from the any documents created by the other software such as
text editor, spreadsheet or presentation software. It is possible to convert to the JPEG file
from the any kinds of documents created by the software which has a "print" menu.
Create the available data
1 Open a document with the individual software.
2 Select a "Print" sub menu and open the printing dialog. On the window, select "Network
Viewer 3 (File Converter 2)" icon on "Select Printer" item and click Print button.
Set the option setting for the page layout
or paper setting by clicking Preferences
button if required.
3 Select a folder and click save button.
The file name is named with "Image001" as
the default. If the converted image has 2 or
more pages, the file names are numbered
from "001" to "999" in a sequential order.
Image quality and Conversion type can be
setup on this window. For further informa-
tion, please see "Setting of the Conversion
Mode" ( p.85).
I
t may appear the white space around the
edges on the converted image depending
on the type of the image data.
The above procedure may differ from each computer environment and applications.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢅꢄ
Creating a program file [Program Editor]
Creating a program file [Program editor]
Network Viewer 3 (Program Editor) is a tool to make a program file which specifies the dis-
play order of the image and its file path in the file server (FTP server). The Program Editor
makes a folder "DispParam" at the login root directory in the FTP server and makes files as
each program name into this folder. These files are called "Program". By specifying the pro-
gram file with the Network Viewer function, you can have the programmed display with
the monitor .
Procedure of making program
1 To launch the Program Editor, click "Network Viewer 3
(Program Editor)" menu from "Start" - "All Programs" -
"Network Viewer & Capture 3" menu.
2Click Connect button.
3If the connection setting window appears, enter the each
item and then click ok button.
The setting window disappears and then the programs
are listed on the window if there are program files at
the login directory in the connected FTP server.
item
Description
Host name............Enter the FTP server name or IP address
Root Folder .................Specify the root directory of the FTP server. Normally use "/".
User ID ....................Enter your login account of the FTP sever or use blank when you login as anonymous
account for the FTP server
Password...............Enter your password (PIN code) or use blank when you login as anonymous account.
iMPortaNt
it is required to set the write permission mode for the login directory of the FtP server.
if only the read only mode, you will have an error when you register a new program.
ꢅ7
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
4 Click New button.
5 Enter a program name and click add button.
Change : Changes the contents of
the program file.
Remove : Removes the program from
6 The folder selection window appears and select a
folder in which the JPEG data are stored and then
click add button to register into the folder lists.
the list.
Add....................Displays the folder selection window.
Delete..............Deletes the folder path from the folder list.
UP.......................Moves up the selected folder path.
DOWN .............Moves down the selected folder path.
Edit.....................Used to set up the display order or display time of the image individually. For further
information see item "Setting up the display order and time of the images" on the
next page.
The order of the display is listed in the folder list window. To change the order of the display,
change the list order of the folder list by using uP or DowN button.
The programs are stored into the "DispParam" folder at the login root directory and this
"DispParam" folder is made by software automatically.
7 Click register button to register the folder list into the program.
8 Click Close button to quit the Program Editor.
ꢅꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a program file [Program Editor]
setting up the display order and time of the images
In the default setting, the display order of the images is ASCII code order of the file name.
To change the display order or to set up the display time, take the following procedure.
Display the folder list window in step 6 of the previous page.
1 Select a folder list contains images to change.
2 Click edit button. The images in the selected folder are displayed with the file name on
the index window.
When selecting "Image" from "View" menu,
the thumbnail of the image will be displayed
(default setting). When selecting "Icon", the
icon image will be displayed.
It takes a time to display thumbnails.
The number in front of the file name indicates
the display order of the image.
Display order
number
File name
Menu
sub menu
Description
File
Edit
Exit................................Closes index window
UP..................................Steps up the display order of the selected images
DOWN........................Steps down the display order of the selected images
Display time...........Sets up the display time of the selected images
Image.........................Displays thumbnail of the images
View
Icon..............................Displays images as the fixed icons
Update.......................Updates images information on the index window
ꢅꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
1
3 To change the display order, select* files and then click uP or DowN button on the
menu bar to move them onto your desired place, or select files and then drag and drop
them onto your desired place with mouse.
2
1
4 To change the display time* , select* files and
then click Display time button on the menu
bar to display the Display time setting window.
Check "Display time" check box and set display
time. To cancel the display time, un-check the
"Display time" check box.
image frame on the index window
Image frame on the index window has 3 kinds of display modes as follows.
No frame
Blue frame
Red frame
: Shows that the image in the folder is unchanged
: Shows that image is added into the folder newly
: Shows that image is deleted from the folder
Added
Moved
*1 Enable to select multiple files at once by using "Shift" or "Control" key, or with mouse cursor.
*2 Enable to set up 3 to 240 seconds for display time.
ꢆ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a program file [Program Editor]
example of the created program selection
Use the web browser to access to the control page of the monitor. Click Viewer of the
Network menu on the web page, then connect to the FTP server and select the program
name which was made at previous section. The monitor starts displaying the images
along the program. For further information, please see "Using the Network Viewer func-
tion" ( p.92).
This function is not available in the light mode.
The limitation of the Program file
There are several limitations for the program file as follows;
* Number of programs in a root folder is less than 1000.
* Number of folders in a program is less than 100.
* Total characters of folder name is less than 255.
* Total characters of program file name is less than 63.
* Do not make a program name started with ".".
* Do not make a program name contained with following characters:
\ / : , ; * ? " < > |
* The program name started with " "(space) is registered with removing the space.
ꢆ1
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
using the Network Viewer function
The Network Viewer is a function to acquire the JPEG image data from the file servers
placed in the network and display them on the monitor. The displayed image data are
specified with the folder unit. You can set the display period and repeating times, and also
you can register those folders as the program. *the network viewer function cannot be
used when using the network capture function.
Condition to use the Network Viewer function:
* Enables to use the FTP service with Windows 2000 Professional or XP Professional.
* User must have a full-access account to the FTP server or the FTP server allows anyone to
use with "Anonymous" account which also has a full-access mode.
* The allowed number of simultaneous access from the same IP address is more than 20.
To use this function, it is necessary to disable "pop-up block" function of the web
browser.
Control by the web browser
MONITOR 2
MONITOR 1
PC1
PC2
JPEG
PC3
PC4
PC6
PC5
Project JPEG
images stored in
PC3 with PC2
Prog.
JPEG
FTP file server
Select input mode to "Network" previously.
1 Access to the control page on the monitor by using the web browser.
From the main menu, click Network - Viewer to display the setting page.
ꢆꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the network viewer function
2 Setup the setting page [1] of Image display setting.
item
Description
Host name............Enter the host name or IP address of FTP server,
yourftp.server etc.
Folder Path ..........Use "/"(root directory) in normal, or enter the
directory name follow the "/" as shown in the
below example if you have a specified direc-
tory in the server.
/data/
1
User ID* .................Enter your login account of the FTP server
Password* ...........Enter your password of the FTP server
1
1
Option* .................Set "Display ON" when you display the
acquired preview images on the web browser.
3 Setup the setting page [2] of Selection display setting.
Click select after selecting from the pull-down menu "Folder Selection" or "Program
Selection" for the Display object. The list window appears and select a program or folder
and then click set on the window.
Displays the
path of the file or
folder selected
Selects the display type either the listed
with file name or listed with thumbnail.
The thumbnail can be selected "4 divi-
sion", "6 division" or "9 division".
This function is not available in the light mode.
See item "Creating a Program file [Program Editor]"( p.87) for about program.
*1 iMPortaNt NotiCe
Please note that if you use the FtP server with personal account except anonymous
account, the user iD and password may be displayed on the browser depending on
the version of the browser. we recommend that this function should be used with the
anonymous account usually.
ꢆꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
When clicking set, the file list or preview list of the selected folder or program is dis-
played on the window.
Decides a image to
start auto display with
Selects a page
The original image is displayed on
another window by clicking on
the preview image or file name
Button
operation
<<...............................Steps down the startup image in
the auto display function
>>...............................Steps up the startup image in the
auto display function
List.............................Switches to the List mode
Thumbnail............Switches to the thumbnail mode
Close.........................Close the window
This function is not available in the light mode.
The preview image will not appear when the option is set "Display OFF".( p.93)
Up to 1000 images can be displayed.
When selecting "folder selection", it displays images placed at the first directory in the selected folder.
The display order of the images is according to the ASCII character order when selecting "folder
selection", or is specified by the Program Editor when selecting "program selection".
ꢆꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the network viewer function
4 Auto Display setting and control page [3]
Repeat times
(0 to 255 times)
* 0 means endless play
1
Display period* of the
image (3 to 240 sec.)
Click here to check the
further information of
the file error
The preview image will not
appear when the option is
set "Display OFF".( p.93)
Error info.
1. Click start button to start the auto-display. The image in the selected folder or pro-
gram is displayed on the monitor's screen. The web browser opens another window
and displays the preview images on the Auto Control window sequentially.
2. Click stop button to stop the auto-display.
• Restart the auto-display, click restart button.
* During the auto-display stops, it enables you to display the images manually by using [<<] or
[>>] button.
3. Click end button to end the auto-display.
• When pressing the error button, the further information of the file error is displayed.
For further error information, refer to the next page.
*1 When selecting the program file for auto-display, the display time of each image gives preference
to the setting specified by the program file over the setting specified by the auto-display function
above. The images not set the display time is according to the display time specified by the auto-
display function above.
The display period is greatly affected by the network environment or the operation of multi con-
trol, so it may not display the image as the specified display period.
The switching is not the same timing between the images on the screen and on the web browser.
ꢆꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
Error information
Description
error type
File Error
It is displayed when the network unit cannot acquire the correct file imag-
es from the FTP server, or when the master monitor is turned off during the
multi-control.
Click error button to check the details.
Connection Error
It may be displayed when the slave monitor is using the Network Viewer
or Capture function during the multi-control. Check which monitor has an
error , see item "Multi Control/Check & Change" ( p.61-62).
When the file error is occurred during the auto-display, you may have the alert e-mail message.
For further information, please see item "3 Option selection for sending alert mail" ( p.39).
ꢆꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
examples of connection
Peer-To-Peer connection
Connecting the monitor (LCD01) to the control computer (PC05) directly.
* UTP cross cable
Computer Name: PC05
Monitor Name: LCD01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
IP Address
: 192.168.0.2
: 255.255.255.0
: 255.255.255.0
Subnet Mask
:
:
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Connecting the monitor (LCD01) to the control computer (PC05) via the hub.
Hub
To another network
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
Monitor Name: LCD01
: 255.255.255.0
IP Address
: 192.168.0.2
: 255.255.255.0
:
:
Subnet Mask
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Computer Name: PC10
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.10
: 255.255.255.0
:
:
When the monitor is connected to the computer directly without hub, the UTP cross cable should
be used.
ꢆꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of connection
The gateway (Router) installed in the network
Connecting the monitor (LCD01) to the control computer (PC05) via the gateway.
Entrance hall
Computer Name : PC205
IP Address
: 192.168.200.5
: 255.255.255.0
Subnet Mask
Default Gateway : 192.168.200.1
DNS
: 192.168.201.1
Monitor Name: LCD01
IP Address
: 192.168.200.15
: 255.255.255.0
Subnet Mask
Default Gateway : 192.168.200.1
DNS
: 192.168.201.1
Hub
Network Group: 192.168.200.x
To another network
IP Address : 192.168.200.1
Gateway (Router)
IP Address : 192.168.100.1
IP Address : 192.168.10.1
Office
Hub
Hub
Computer Name: PC05
Computer Name : PC10
Computer Name : PC51
Computer Name : PC61
IP Address
: 192.168.10.10
: 255.255.255.0
IP Address
: 192.168.10.51
: 255.255.255.0
IP Address
: 192.168.10.61
: 255.255.255.0
IP Address
: 192.168.10.5
Subnet Mask
Subnet Mask
Subnet Mask
Subnet Mask
: 255.255.255.0
Default Gateway : 192.168.10.1
Default Gateway : 192.168.10.1
Default Gateway : 192.168.10.1
Default Gateway : 192.168.10.1
DNS
: 192.168.201.1
DNS
: 192.168.201.1
DNS
: 192.168.201.1
DNS
: 192.168.201.1
Network Group: 192.168.10.x
ꢆꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
web browser setting
This product is designed to enable the monitor to be set up and controlled from an
Internet web browser. Depending on the preference settings of the web browser, some
control functions may not be available. Please make sure that the following functions are
set up properly in the web browser.
active script/Javascript enable
There are some control items used with
the JavaScript function in the setting
pages. If the web browser is set not to use
this JavaScript function, it may not control
the monitor properly. In this case, the fol-
lowing warning message will be displayed
on the top of the page. To enable the
JavaScript, please see further instructions
on the next page.
Flash Player enable
The setting page of this product contains
the Flash contents. To display the setting
page, the Adobe Flash Player version 6
or later is required to be installed on your
computer. For further product informa-
tion, see the Adobe homepage. (http://
www.adobe.com). Even if your computer
provides the Adobe Flash Player and the
setting page does not appear on the web
browser, check that Flash Player Plug-
In(Shockwave Flash) is installed and set up correctly. please see further instructions on the
next page and it is depending on the web browser.
Proxy setting
In some cases, your web browser is set up to use the proxy server for the internet or
intranet connection. In this case, when you install this product into the local network, you
should set up the proxy setting of web browser preference correctly. Especially when con-
necting the monitor and computer with a UTP cross cable directly, or when the network
does not provide the proxy server, make sure that "not use proxy server" is set up in your
web browser preference. Please see item "Examples: OS/Browsers" in the next page for
further setting up procedure.
There are various ways to change your browser preferences depending on the version or applica-
tions. Please see the setting instructions on next page for example and also refer to on-line help
of your web browser.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Web browser setting
examples: os/Browsers
windows XP Professional
Internet Explorer v.6.0
activescript setting
Select internet options from tools menu on the web browser and then select security
tab and click Customize Level… button. On the security setting window, scroll down and
find the scripting item, make sure that "Enable" is selected in item active scripting.
Flash Player enable
activeX controls and plug-ins setting
Select internet options from tools menu
on the web browser and then select security
tab and click Customize Level… button. On
the security setting window, scroll down and
find the activeX controls and Plug-ins item,
make sure that "Enable" is selected in item run
activeX controls and plug-ins.
101
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Flash Player add-on setting
Select Manage add-ons... from tools
menu on the web browser. Select "Add-ons
currently located in Internet Explorer" from
show pull-down menu. Make sure that the
"Shockwave Flash Object" is listed under the
item "Enabled".
Proxy setting
Select internet options from tools
menu on the web browser and then select
Connection tab and click LaN settings
button. Properly set up your web browser's the proxy server settings according to the
local area network environment to which the monitor is connected.
- using proxy server
To use an external internet connection from the local area network, check the item use a
proxy server and enter the proxy server address and port correctly in the proxy settings
window. For further instruction please consult your network administrator.
- Not using proxy server
Uncheck the item use a proxy server.
If you connect the monitor to the computer directly with UTP cross cable, this must be
unchecked.
To designate proxy settings that will not use the
proxy server when accessing the monitor installed
in the local area network, enter the IP address or
domain name here.
10ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Web browser setting
Netscape Navigator v.ꢀ.0
Javascript setting
Select Preference from edit
menu on the web browser
an d th en s ele c t th e item
advanced/scripts & Plugins
in the Category column. Make
sure that the enable Javascript
for Navigator is checked.
Flash Player enable
Flash Player Plug-in setting
Select about:Plug-ins from Help
menu on the web browser. The
plug-ins software provided on the
browser are listed on the page.
Check that the Flash Player Plug-
in (shockwave Flash) is installed
and set up correctly as the below.
10ꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Proxy setting
Select Preference from edit menu on the web browser and then select the item advanced/
Proxies in the Category column. Properly set up your web browser's the proxy server set-
tings according to the local area network environment to which the monitor is connected.
- using proxy server
When you use an external internet connection from the local area network, select the item
Manual proxy configuration. Enter the proxy server address and port number correctly on
HttP Proxy item. For further instruction please consult your network administrator.
- Not using proxy server
Select the item Direct connection to the internet in the proxy setting window.
If you connect the monitor to the computer directly with UTP cross cable, this must be
selected.
To designate proxy settings that will not use
the proxy server when accessing the moni-
tor installed in the local area network, enter
the IP address or domain name here.
10ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Product specification
Product specification
Type.......................................................... LD-Net Organizer (network unit)
LAN interface...................................... Applicant regulation IEEE802.3 (10Base-T)
IEEE802.3u (100Base-TX)
Data transfer speed
Data transfer mode
10Mbps/100Mbps
Half duplex/Full Duplex
8-pin modular (RJ-45)
TCP/IP
Terminal
Network protocol.............................TCP/IP specification
Power source...................................... Supplied from the monitor
Power consumption...................... 3.0 watts
Dimensions (W x H x D)............... 5.20" x 4.13”x 1.32”(132 x 105 x 33.6 x mm)
Weight.................................................... 0.57 lbs (258 g)
Built-in battery................................... Lithium battery, Type CR2032, 3.0V
Operating temperature ............... 41˚F ~ 95 ˚F (5˚C ~ 35 ˚C)
Storage temperature..................... 14˚F ~ 140˚F (-10˚C ~ 60˚C)
* The specifications are subject to change without notice.
10ꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Port specification
LAN port specification
8-pin modular connector (rJ-45)
1 2 3 4 5 6 7 8
Pin No.
Signal
Function
1
2
3
4
5
6
7
8
TX+
TX-
Transfer data (+)
Transfer data (-)
Receive data (+)
RD+
(not used)
(not used)
RD-
Receive data (-)
(not used)
(not used)
10ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q&a
installation/access
Q
A
Why doesn’t the setting page appear in my web browser?
Following causes are possible. Please check them.
1. The monitor does not connect to the network.
Check LED indicators status ( p.17).
- Check the connection of LAN cable if the LINK indicator does not illuminate
red.
- Check the network configuration of the monitor if ACT indicator does not
illuminate green.
2. Wrong network configuration of the monitor
Check the network configuration of the monitor ( p.37).
3. Wrong network configuration of the computer.
Check the network configuration of the computer.
4. The network unit is used with the default setting ( p.21).
5. The proxy setting of the web browser is not set correctly ( p.100).
6. The computer does not provide TCP/IP protocol.
Q
A
No setting page in my web browser? Is the problem in the network or in
the monitor? I would like to find out the problem whether it is in the net-
work or in the monitor
Check it by the following steps
1. Disconnect the monitor from the network and connect the monitor and com-
puter with the UTP cross cable directly.
2. Change network configuration of the computer and monitor as shown in the
example below.
(Monitor setting)
IP Address
Subnet Mask
Default gateway
DNS
(Computer setting)
IP Address
Subnet Mask
Default gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 192.168.0.5
: 255.255.255.0
: (blank)
: 0.0.0.0
: (blank)
107
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
3. Enter the monitor’s IP address [192.168.0.2] at "Address" column on the Web
browser. [Note] Make sure that the proxy setting of your web browser is set
"Not use a proxy server" ( p.100).
4. If the login page appears, this product is operating properly. The problems
may be in the network configuration of the computer or in the network. Please
try to set up the network by following item "Network configuration" ( p.21).
If the login page does not appear, please check for proper mounting of this
product onto the monitor by referring to chapter "Installation and Network
configuration" ( p.18-19).
Q
A
How can I restrict access from the computer.
1. Please use the password authentication function on the login page ( p.30).
2. Please use the IP filtering function provided with the gateway (router) to
restrict the accessing from the computer. For further information please con-
sult your network administrator.
Q
A
Can I access the monitor installed on the company’s local area network
from a remote location?
There are some ways to access to the monitor in the LAN, but you must consult
your network administrator for security reason.
Use of modem
(Connect to the company’s network from your home or some other places by
using modem.)
Use of private line
(Connect to the company’s network from the branch office or maintenance
office by using private line.)
Use of internet
(Connect to the company’s network from your home, branch office or some
other places by using the internet.)
Q
A
We use the DHCP/BOOTP server to assign the IP address. Is it possible to
use the network unit in this network environment?
Possible. As the network unit does not support the DHCP/BOOTP server, the fixed IP
address must be configured manually. Please consult your network administrator (
p.25).
10ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
How can I install several monitors equipped with the network unit?
Install and configure network one by one to avoid the IP address collision each
other ( p.25).
To configure the IP address please see item "Network configuration" ( p.21).
Q
A
How many monitors can I control with multi-control function?
It has been designed to control up to 100 sets but it depends on the network envi-
ronment.
Password/Login
Q
A
What should I do when I forget the password?
If you forget the Network PIN code to the monitor, you can initialize PIN code and IP
Address/Sub net/Gateway/DNS by selecting "Network initial" from "Installation
mode" menu on the monitor. For further information, please see instruction manual
of the monitor.
Q
A
Can I register the setting page as a web browser "Favorites" or
"Bookmarks"?
Please add "Login" page to your "Favorites" or "Bookmarks". Do not add the speci-
fied setting page because it will not be able to perform the password authentica-
tion correctly.
10ꢆ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
operation
Q
A
Why can't I change the controls in the setting page with web browser?
Please make sure the monitor is turned on. If it is in the standby mode, the setting is
not effective to the monitor. To control the monitor with a web browser, the moni-
tor must be in the powered-on condition. Also, monitors registered for multi-con-
trol cannot have any controls changed if they are in standby mode. But timer and
clock settings are always effective, even for monitors in standby mode.
Q
A
Why does it sometimes take a lot of time to complete the page display?
The display speed of the page depends on the network environment in which both
the monitor and computer are placed. It may take much time to complete the page
display if network traffic is heavy. Please consult your network administrator. You
can select the Light mode for displaying pages quickly ( p.30).
Q
A
I use many of the monitors in the network. How can I use names of the
monitors to recognize each monitor instead of IP addresses?
You can manage the monitors with nicknames instead of the IP address. Please see
item "Multi-control" for further information ( p.59).
By registering the monitor name and IP address with the DNS server, it can be
accessed with the nickname from the any computer referred to the DNS server.
Please consult your network administrator.
Q
A
How many numbers of the E-mail address can I register in the E-mail set-
ting page.
You can register up to 10 addresses.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
Why am I not receiving E-mail alert messages?
Make sure that the registered E-mail address and SMTP server address are correct. If
the SMTP server is located in your LAN (Local Area network), the address should be
set to the SMTP server in your LAN. The SMTP server located outside of your LAN
may not be available for security reason. For further information please contact your
network administrator ( p.38).
It may be required for the authentication depending on the SMTP server. This prod-
uct does not support this kind of SMTP server.
111
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Q
A
Can I update the firmware of the network unit.
It is possible to update the firmware through the network. It is required to have a
special tool for the updating. For further information please consult your local deal-
er. The version number of the firmware is indicated on the lower part of the "Initial
setting" page.
Version of the
firmware
11ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
What are the rules for IP address assignment?
If the network is constructed with TCP/IP protocol, a unique IP address is required
for each piece of network equipment. The following are basic rules of the assign-
ment.
Rule1
Do not configure the same IP address to the network equipment in the
same network group. Each piece of equipment must be assigned a unique IP
address.
If the IP address is set [192.168.x.x], the Subnet Mask should be set
[255.255.255.0] for example.
Rule2
The start address [xxx.xxx.xxx.0] and the last address [xxx.xxx.xxx.255] of
the IP address must not be assigned to any other equipment. These address
numbers are reserved.
Rule3
The IP address must correlate to a network number. If network numbers are
different between the equipment, they cannot establish communications
each other. In this case, the router is placed in the networks to make the rout-
ing.
Q
A
What is the MAC address assigned to the network unit?
The MAC address is indicated on the case back as the below.
MAC Address
MAC address
11ꢁ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Network capture
Q
A
Why doesn’t the computer screen appear on the monitor?
1. Make sure that the input mode of the monitor is "Network".
2. Make sure that the Network Capture icon on the task bar of the computer is active
(
p.66).
3. Check the parameter set up ( p.67).
Make sure that the numbers of the capture port is the same as the monitor’s port
number. The default port number is 9000. If the alert message "Invalid Port No."
appears, your computer may be using this port number already. In this case, use
another port number.
4. Check the IP address of the computer is registered to the network unit correctly (
p. 68).
5. Make sure that your computer is not using the firewall function. The network unit
may not be able to use the port due to this firewall function. In this case, please
turn off this function temporarily. There are also some port limitations on the net-
work equipment such as router. Please consult your network administrator.
Network Viewer
Q
A
Images from the file server don’t appear on the monitor?
1. Make sure that the input mode of the monitor is "Network".
2. Check the account setting of the FTP server ( p.93).
3. The files in the FTP server must be optimized JPEG and converted by using the File
Converter 1 or 2. Please check data format. ( p.83)
4. There are several limitations for image file name and program name. Please check
file names and program names ( p.91).
5. Make sure that your computer is not using the firewall function. The network unit
may not be able to use the port due to this firewall function. In this case, please
turn off this function temporarily. There are also some port limitations on the net-
work equipment such as router. Please consult your network administrator.
Q
A
I cannot make a new program file.
Check your account of the FTP server. You must have a mode "Write enable" for its
account.( p.87)
11ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
File Converter 1
Q
A
What kind of image formats can I convert?
The File Converter 1 enables to convert to the JPEG format from the following
image format.
Bitmap format (.bmp)
JPEG format (.jpeg .jpg)
Microsoft power point format (.ppt)
File Converter 2
Q
A
Sometime I have the white frame images converted by the File Converter
2?
It may have images with white frame due to the paper margin of the print driver
depending on the image data.
11ꢃ
LD-NET ORGANIZER
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
owNer's MaNuaL Poa-LN02
iFkM
saNYo electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|