INSTRUCTION MANUAL
Outdoor Housing
This installation should be made by a qualified service
person and should conform to all local codes.
VA-80EX
About this manual
This housing is designed for outdoor installation.
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
CAUTION:
Install this housing securely according to this
installation manual. Be aware that allowing the bracket
to fall with the camera on it may cause personal injury.
Important
• Be careful when opening holes for installing the
unit. Work with the power and video cables pulled
out for easy installation.
• Make sure to properly perform waterproofing for the
ceiling or wall where you are installing the unit.
• Make sure that the surface in the installation
location has no unevenness and is strong enough
to bear the total weight of the unit.
b Specifications
Color: Beige
Material: Metal
Waterproof Standard: Conforming to IP66
Operating Environment
(with power source connected) :
Temperature; -30°C - +50°C (-22°F - +122°F)
Humidity; less than 90% RH (no condensation)
Weight: Approx. 2.5 kg (5.5 lb)
Dimensions:
Example of
Example of
wall mounting
pendant mounting
Accessories
Ǿ248 (9.8)
Unit: mm (inch)
Hexagonal wrench
b Specifications of Heater
(built into VA-CM8C/CM8S)
Screws, washers
(for power board unit)
Automatic switch ON/OFF temperature:
ON; Approx. 5°C (41°F)
OFF; Approx. 15°C (59°F)
Power supply: 24 V AC 10%, 50/60Hz
Waterproof tape
Power consumption: Max. 35 W (When heater turned on)
Features and specifications are subject to change without
prior notice or obligations.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Outdoor Housing
● For the built-in heater and fan in the dome cover, you need an additional 24 V AC power supply.
● This housing is used in combination with a dome cover (clear/smoked) and a mounting bracket (wall/
pendant) that are sold separately.
☞ For how to install an assembled housing, refer to the instruction manual for the bracket used.
Also refer to the instruction manual for each associated device.
3. Connecting cables
1. Attaching the dome cover
1Connect the 24 V AC power cable to the terminal (F).
Hook the safety wire (A) of the dome cover on hook
hole (A’) located inside the housing.
1
2
Connect the heater cable (B) to the heater terminal
(B’) and the fan cable (C) to the fan terminal (C’).
F
C
A
B
2Connect other cables to the power board unit.
B’
☞ For details, please refer to “Connections and Settings”
in the Installation Manual that comes with the camera
unit.
Dome Cover:
• VA-CM8C (Clear)
• VA-CM8S (Smoked)
A’
C’
4. Mounting the camera unit
Fasten the camera unit safety wire (G) to the hook
(G’) inside the power board unit.
1
2. Mounting the power board unit
Pass the supplied screws
unit screw holes (D) and fasten them loosely using
through power board
Align the arrows (E) of the same color (blue) on the
2
1
2
camera unit and the housing inner face, and push
washers
(4 places).
the camera until you hear a click.
Mount the power board unit in the housing aligning
the arrows (E) of the same color (blue) on them,
3Remove the plastic cover (H) of the camera unit.
and then firmly tighten the screws
fastened in the previous step.
• Make sure the terminal (F) and its cable are located
along the inner lateral face of the housing.
• Pull the video cable led from the ceiling or wall
toward the power board unit.
loosely
Attach the dome cover by fastening 4 screws (J)
4
using the supplied hexagonal wrench.
G’
Power Board Unit:
VA-84S/80S
Video cable
D
D
G
D
D
a
E; Blue
E; Blue
b
F
Fix the housing onto the mounting bracket (wall/
pendant).
*
3
J
*
☞ For details, please refer to “Outdoor Type” in the
Mounting Bracket Instruction Manual.
H
J
J
* To remove the camera unit
J
2
Download from Www.Somanuals.com. All Manuals Search And Download.
|