Instruction Manual
LCD Monitor
CE52LH1R
Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
SERVICING
Servicing
Your monitor is fully transistorised and does not contain any user serviceable components.
You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage
objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively
use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare
parts can prevent fire, shock and other hazards.
Unplug the LCD monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:
I If the power cord or plug is damaged.
I If liquid has been spilt in to the LCD monitor.
I If the LCD monitor has been dropped or the cabinet has been damaged.
I If the LCD monitor exhibits a distinct change in performance.
I If the LCD monitor does not operate normally by following the operating instructions.
Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. This will
often require extensive work by a qualified technician to restore the monitor to normal operation.
Important recycling information.
Your SANYO product is designed and
manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be
disposed of separately.
In the European Union there are separate
collection systems for used electrical and
electronic products.
Please help us to conserve the environment we live in!
Note: This symbol mark and recycle system are applied only to
EU countries are not applied to other countries of the
world.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
AC Power Cord Requirement
The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you pur-
chase it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard
Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to make sure that the plug will fit into the power outlet. Do not try to
defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE
End-User License
G reverse-engineer, decompile or disassemble the Software;
The product (meaning the equipment or appliance to which this
G make the Software (or any part of it) available, or permit its
documentation relates) incorporates Software (the software applica-
redistribution, for use with any computer hardware other than
tions, utilities and modules embedded within the Product) which is
the Product; or rent, lease, gift, loan, sell, distribute or transfer
owned by Sanyo or its licensors. Before using the product, please
possession of the whole or any part of the Software.
read the End-User License Conditions detailed below. If you do not
agree to the terms and conditions of the End-User License, Please
do not proceed to use the Product- repack the Product unused and
Termination
return it to your supplier together with proof of purchase for a full
refund. By using the product, you agree to be bound by the terms
and conditions of the End-User License.
This license is effective until terminated. This license will terminate
automatically without notice if you fail to comply with any of its
provisions.
Disclaimer
License Grant, Conditions and restrictions
1. The Software is(to the extent permitted by law) supplied ‘as is’ and
SANYO and its suppliers expressly exclude all warranties, express
or implied, including (but not limited to) warranties of satisfactory
quality, fitness for purpose and non-infringement (save to the
extent that the same are not capable of exclusion at law).
1. Sanyo grants you a non-exclusive, world-wide (subject to export
controls), non-transferable (except as permitted by 2 below),
royalty-free license to use the Software upon and with the Product.
2. You may not transfer any of your license rights in the Software
without the prior written consent of SANYO and if consent is
provided then the Software shall only be transferred in conjunction
with the transfer of the Product AND provided that the transferee
has read and agreed to accept the terms and conditions of this
license.
2. In no circumstances will SANYO be liable for any direct, indirect,
consequential, or incidental damage (including loss of profits,
business interruption, loss of data or the cost of procurement of
substitute goods, technology or services) arising out of the use or
the inability to use the Software (save to the extent that such
liability is not capable of exclusion at law).
3. You must ensure that the copyright, trademark and other protective
notices contained in the Software are maintained and not altered
or removed.
General
1. This End-User License will be governed by laws of England and
the User may only bring claims in the English Courts and SANYO
shall be entitled to bring a claim in the courts of any jurisdiction.
2.This End-User License is governed by the laws of the State of
California. The End-User and Sanyo agree that any action to
enforce or interpret the terms of this End-User License shall be
brought only in the appropriate state or federal court located in Los
Angeles County, California.The End-User and Sanyo hereby
submit to the exclusive jurisdiction and venue of such court.
4. The Software provided hereunder is copyrighted and licensed (not
sold). SANYO especially does not transfer title or and ownership
rights in the Software to you. The Software provided hereunder
may contain or be derived from portions of materials provided to
SANYO under license by a third party supplier.
5. Except as expressly permitted by statute you may not;
G use the Software in conjunction with any other computer
hardware other than the product;
3. The above terms and conditions supersede any prior agreement,
oral or written, between you and SANYO relating to the Software.
G copy all or part of the Software;
G incorporate all (or any of) the Software into other programs
developed by (or on behalf of) you and/or used by you;
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
INSTALLATION
Step : 1 Mains Connection
I Connect the display unit to VGA, BNC and Scart connector as
required.
R
R
L
L
AV2-IN
PJ-Net
N5VW
N
5V
W
1. Connect the in-line power connector to the connector attached to
the LCD monitor as shown above.
4. AV3
Composite (CVBS) signal input
AV3 OUT is to output the composite video signal from the VIDEO IN
so that you can connect monitors with the use of a loop through
function.
2. Connect the power cord of the LCD monitor to a wall outlet.
i As this product does not have a mains On/Off switch, please
ensure your mains plug is easily accessible.
5. DVI-D (Digital Video Interface)
This monitor has a DVI connector. This is located at the back of the
monitor next to the phono sockets. This input will support a large
range of resolutions as shown on page 14. See page 7 for details of
menu operation.
i The LCD monitor is prepared for a mains voltage AC120V, 50Hz/
60Hz. To completely switch off the mains, or when the display
unit is not to be used for an extended period of time, it is advis-
able to disconnect the power cord from the power outlet.
R
R
L
L
AV2-IN
AC
Ma
i
ns
Out
6. PC connection
l
e
t
This LCD monitor has a PC connector (PC-IN D-SUB). You can
connect a PC to the LCD monitor and use it as a monitor display (see
page 9). This input will support a large range of resolutions (see page
14). Audio can be connected via the 3.5mm PC audio in socket.
7. PJ Net IN: Has the ability for PJ-NET to be connected to
control the monitor using a network.
i Please use the correct mains lead supplied with the set for your
area.
3. Warning: To prevent injury, the unit must be securely attached to
the wall in accordance with the installation instructions.
WARNING! High voltages are used in the operation of
this set. Refer service to qualified service personnel.
Step : 2 Connections
I
INPUT selection
To switch between AV1, AV2, AV3, PC or DVI press the INPUT button
on your remote control repeatedly.
1. AV1
SCART connection
2. RGB
TTL input (5V RGB signals) into SCART terminal
3. Y,Pb,Pr/ RGBHV connection (AV2)
This LCD monitor has a choice of Y, Pb, Pr or RGB H/V connections.
You can connect your DVD player to the Y, Pb, Pr terminals instead
of using a scart lead. This can support high definition in analogue
component form. RGB H/V can be used as a PC input via the BNC
terminals.Both options support a large range of resolutions (page 14).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
REMOTE CONTROL
Input
Standby
To switch input source from AV1, AV2, AV3, PCor DVI mode.
To switch the monitor on and off. Also see page 7.
Recall
To display input selection information and the Time set.
You can also select colour systems in AV3 mode as follows:
AUTO-> PAL -> SECAM -> NTSC -> NTSC4.43
It can also be automatically adjusted in PC mode by pressing
this button for twice .
Wide
To select the screen mode Full, Zoom, Zoom [Caption-IN],
Normal, Natural wide,.
Refer to page 11.
Back
Used to return to the previous menu.
Menu
To enter and exit the main menu, and sub menu.
Up and Down
To select the next or previous item.
Level Up/Down
To enter sub menus.
F/OK
To confirm the initial setting in the menu.
Picture mode selector
.
Press the -> <- button repeatedly to select the following
picture mode.
Bass Expander
Personal-Personal preference mode.
Standard-Normal viewing mode.
Dynamic-Suitable for brightly lit rooms.
Soft-Inhibit strong contrast and color, it is beneficial for eye
protection.
To get an emphasised bass sound ON or OFF.
TXT/TV
To select Teletext mode.
Eco-Suitable for dimly lit rooms and gives a cinema-like
effect.
Main/Sub Picture Swap
To swap Main and Sub picture.
Freeze
To switch picture still on or off.
ON/OFF
To switch OFF ->PIP(1) ->PIP(2) ->POP mode in turn.
Green
Refer to page 12.
Press this button for more than 4 seconds and release,
installation mode will appear.
Remote control battery installation
Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the
batteries match the "+" and "-" marks inside the unit into the remote
control handset.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
INSTALLATION
Controls and Menus
Menu Operation
Many of your monitors functions are controlled through the menu
function, using the remote control.
MENU
Picture
Brightness
Contrast
Color
Tint (only if NTSC equipment is detected)
Sharpness
White Tone
White Tone / R / G / B
Advanced Setting
DCDi / ACC/ACM / CCS / DNR / MPEG NR / Film Mode
Sound
Timer
Treble
Bass
Balance
Bass Expander
On / Off
Current Time
Off Time
On Time
On Position
AV1 / AV2 / AV3 / PC / DVI
Setup Menu Setup
PIP / POP Setup
Language / H/V-Position / Duration / Transparence
PIP/POP Mode / Main/Sub Source / PIP Position
Initial Settings
Text Language
Tile Mode
Western / Eastern / Russian / Arabic / Farsi
Tile Mode Active / H/V_Sets / H/V Location / Bezel H/V Adjustment
RGBHV / YPbPr
AV2 Setting
1
2
PC Adj. Auto Adjust
H-Position
V-Position
Clock
1. The LCD display has a Standby light to show there is power.
Phase
Switching into/from standby mode
The Standby mode is used for switching the LCD monitor off for
short periods of time. In standby mode the monitor is switched
off but is still receiving mains power.
During menu operation the bottom of the on screen display will show
which controls can be used for menu navigation.
Press the MENU button to enter the main menu. Whenever main
menu is accessed initially, PICTURE will be the defaulf selection.
G To turn the monitor into standby mode, press the 4 button.
The blue power indicator illuminates more brightly.
A sub menu is selected using the 5 or 6 button and pressing
the 1 or 2 button when the required sub menu is highlighted.
When you have finished you can press the BACK button to return to
the previous menu, press the MENU button to exit the menu
operation.
G To turn the monitor ON from standby mode, press the 4
button again.
If you find the power indicator flashing, disconnect
power cord from the power outlet and contact our
Service desk.
This warning is a sign to let you know that the power
protection function of this TV set is now operating.
2. Control buttons (bottom corner of back cover)
Picture menu
Menu button: Used to display or cancel main menu.
1. Press the MENU button. PICTURE will be the default selection.
Press the 1 or 2 button to enter.
Set the picture settings for your “personal” preference.
Input/ d button: Switch between AV1, AV2, AV3, PC or DVI
mode.
1 or 2 buttons: provide up and down adjustments.
4 button: To switch to standby mode (to switch off completely
2. Use the 5 or 6 button to select eg. Brightness and the 1
disconnect the monitor from the power supply).
or 2 button to adjust levels.
I White Tone
May be used to adjust the color tone of the picture. Use the 5 or
6
button to select White Tone and press the 1 or 2
button to enter the sub menu. You can select Personal, Cool,
Standard or Warm settings by using the 1 or 2 button. To
adjust the color tone of the picture by using the 5 or 6 button to
select Red(R), Green(G) or Blue(B) and the 1 or 2 button
to adjust levels. These settings will be stored in personal mode
automatically.
60
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
MENU OPERATION
I Current Time
Use NUMERIC buttons [0-9] to set Current time. (00:00~23:59)
Picture menu
To reset the time using the 1 or 2 button.
i Other items in Time Menu cannot be selected until Current Time
has been set.
I Advanced settings
Use the 5 or 6 button to select Advanced settings and press
the 1 or 2 button to enter the sub menu as follows.
I Off Time
The Off time will switch the monitor into the standby mode when the
selected time has elapsed.
Use NUMERIC buttons [0-9] to set Off Time. (00:00~23:59)
To reset the time using the 1 or 2 button.
i If the monitor is switched off by the standby button 4, the timer
settings will be cancelled.
i About one minute before the set time is reached, the status of the
monitor will display on the screen.
DCDi(Directional Correlational Deinterlacing) is used to process
moving angled edge in deinterlacing to get the smoothest and most
natural image. Press the 1 or 2 button on the remote control
to select On or Off.
I On Time
Once On Time has been set, you will not miss your favourite tv
programme.
Use NUMERIC buttons [0-9] to set On Time. (00:00~23:59)
To reset the time using the 1 or 2 button.
ACC/ACM(ACC: Adaptive Contrast and Color; ACM-II: Active Color
Management-II) is used to select adaptive Brightness, Contrast and
tone control. Press the 1 or 2 button on the remote control to
select suitable mode either Vivid, Cinema, Sport or Off.
i
Once On Time has been set, when the set time is reached, the
monitor will leave the stand-by status and enter to the source
automatically.
i
After On Time has been set, you can go on watching other
programs. When the set time is reached, the monitor will display
"Note: Time is up!" and then will automatically switch to
the preset program.
CCS(Cross Color Separation) is used to remove residual chroma
information from luminance signal which is the result of imperfect
decoding of composite video. Press the 1 or 2 button on the
remote control to select either Auto, Standard or Off.
DNR(Digital Noise Reduction) is available for noise reduction. Press
the 1 or 2 button on the remote control to select either Auto,
Low, Mid, High or Off.
I On Position
i On Position can only be selected whenOnTime has been set.
Once On Position has been set, when the set time is reached, the
monitor will enter to the preset source automatically.
Use the 1 or 2 button to select the preset source AV1, AV2,
AV3, PC orDVI.
MPEG NR(MPEG Noise Reduction): Removes unwanted ringing and
block noise from images that have undergone MPEG or JPEG
compression and decompression. Press the 1 or 2 button on
the remote control to select On or Off.
Setup menu
Press the MENU button and select Setup using the 5 or 6
buttons, press the 1 or 2 button to enter. Press the BACK
button to return to the previous menu. Press the MENU button to exit
menu operation.
Film Mode(Inverse 3:2 pulldown): Film vs.Video-Detect film.
Performed on material which underwent technologic conversion to
video. Press the 1 or 2 button on the remote control to select
On or Off.
Sound menu
Press the MENU button and select Sound using the 5 or 6
buttons, press the 1 or 2 button to enter.
6I\Q^Mꢀ:M[WT]\QWV
@/)
I Menu Setup
Whenever Setup menu is accessed initially, Menu Setup will be the
default selection. Press the 1 or 2 button to enter the sub
menu.
Select and adjust to obtain the best sound settings for your
environment using the 5 or 6 button to select Treble, Bass or
Balance and the 1 or 2 button to adjust levels.
Bass Expander can also be selected using the 5 or 6 button
and pressing the 1 or 2 button to select On or Off.
These settings automatically store when you exit the menu.
Press the BACK button to return to the previous menu.
Press the MENU button to exit menu operation.
Time menu
Language is preset to English.
Press the MENU button and select Time using the 5 or 6
buttons, press the 1 or 2 button to enter. Press the BACK
button to return to the previous menu. Press the MENU button to exit
menu operation.
H-Position changes the OSD position horizontally by using the 1
or 2 button.
V-Position changes the OSD position vertically by using the 1 or
2 button.
Duration is used to set the display time of the MENU by using the
1 or 2 button.(5~120 seconds)
Transparence is used to adjust transparence of menu. Use the 1
or 2 button to adjust levels.
i If the monitor is switched off by the standby switch 4 on the
back of the LCD monitor the time settings will be cancelled.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
MENU OPERATION
I AV2 Setting
Setup menu
Use the 5 or 6 button to select AV2 Setting and press the
1 or 2 button to select YPbPr or RGBHV.
I PIP/POP Setup
Connect your PC to either PC-IN or RGBHV on the rear of the set.
Once connected select PC mode or AV2 (RGBHV, see page 5 for
AV2 input settings) via the INPUT button on your remote control.
The set will become a monitor for the PC.
Use the 5 or 6 button to select PIP/POP Setup and press the
1 or 2 button to enter the sub menu.
I Native Resolution
Use the 5 or 6 button to select Native Resolution and press
the 1 or 2 button to select XGA or WXGA 1366 x 768.
PC Adj. menu
PIP/POP Mode: Using the 1 or 2 button select the most
suitable mode PIP1, PIP2, POP or Off. (Please refer to page 12.)
i When Mode is set to Off, Sub Source and PIP Position will not
work.
Main Source is used to select input source (AV1, AV2, AV3, PC or
DVI ) for main picture by using the 1 or 2 button.
Press the MENU button and select PC Adj. using the 5 or 6
buttons, press the 1 or 2 button to enter. Press the BACK
button to return to the previous menu. Press the MENU button to exit
menu operation.
Sub Source is used to select input source (AV1, AV2, AV3, PC or
DVI) for sub picture by using the 1 or 2 button.
i For a combination of main picture and sub picture: only DVI
input can assemble with other input source. For
example, if main source is selected as AV1 input, then the sub
source must be DVI input.
PIP Position: Using the 1 or 2 button it can be selected
Top Left, Top Right, Bottom Right or Bottom Left.
Auto Adjust is used to automatically detect incoming signal, and
adjust itself to optimize its performance by using the 1 or 2
button. If the image is not displayed properly, a manual adjustment
is required (Refer to following adjustments).
I Initial Settings
This function returns all setting values except for Dealer Mode and
channel messgaes by using this function.
H-Position is used to move the horizontal picture position by using
the 1 or 2 button.
I Text Language
Use the 5 or 6 button to select Text Language and press the
1 or 2 button to select Western, Eastern, Russian, Arabic or
Farsi.
V-Position is used to move the vertical picture position by using the
1 or 2 button.
I Tile Mode
Clock is used to eliminate flicker from the image by using the 1
or 2 button.
This function allows you to split an image to suit your monitor grid
format to create a video wall.
Use the 5 or 6 button to select Tile Mode and press the 1
or 2 button to enter the sub menu as follows.
Phase is used to eliminate disorder from the image by using the
1 or 2 button.
H_Sets
V_Sets
Tile Mode Active can be set On or Off using the 1 or 2
button.
H_Sets is used to divide the horizonal picture into more than one
part, but the most is 5 parts.
V_Sets is used to divide the vertical picture into more than one part,
and the most is also 5 parts. Using the 1 or 2 button to set.
H Location is used to select one part of the horizonal picture to
display on the current LCD Monitor using the 1 or 2 button.
H Location is used to select one part of the vertical picture to
display on the current LCD Monitor using the 1 or 2 button.
Bezel H Adjustment is used to bezel horizonal adjustment to
smooth image using the 1 or 2 button. (0~10)
Bezel V Adjustment is used to bezel vertical adjustment to smooth
image using the 1 or 2 button.(0~10)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
INSTALLATION MODE
I DCR
Installation Mode
Select DCR usinig the 5 or 6 button, once highlighted you can
select On or Off by pressing the 1 or 2 button.
Installation Mode
I Main S/W Version
To record the version for Main Software.
I Temperature Error
This function can record times for abnormal temperature.
I IP Address / Subnet / Gateway / DNS
These 4 items display the PJ-Net information. If no PJ-NET had
been connected, all the items would be displayed “000000000000”.
i Disconnecting the mains supply before exiting Installation Mode
will cancel the following features On program, RC inhibition, Address
and Baud Rate.
1.08
Temperature Error
This LCD monitor allows you to set up the following:
SETTING PROCEDURE
1 . Press and hold the GREEN button on the remote control for 4
seconds. (Installation Mode will appear)
2. Use the 5 or 6 button to highlight each option, use the 1 or
2
button to adjust each option. Press the MENU button to exit
the mode.
I On Program
Select ON program using the 5 or 6 button, select the start up
position using the 1 or 2 buttons.
(Off/ AV1/ AV2/ AV3/ PC/ DVI)
I Max Volume
Select Max volume using the 5 or 6 button, use the 1 or
2 buttons to set the maximum volume required.
I Winter mode
This Function can be activated when the LCD monitor is used during
cold temperature conditions, approximately 38˚F/ 4˚C or below to
maintain picture performance.
Using the 5 or 6 button select winter mode, once highlighted
you can select ON or OFF by pressing the 1 or 2 button.
IMPORTANT: The AC cord should not be disconnected during the
operation of Winter mode function.
When in winter mode, power consumption is higher than normal
standby consumption. This is entirely due to the operation of heating
circuitry. We strongly recommend to turn off Winter mode when the
ambient temperature is above 38˚F/ 4˚C.
I RC inhibition
You can prevent unwanted remote control operation by selecting RC
Inhibition.
Select using the 5 or 6 button. Press the 1 or 2 button
to select On or Off.
To re-instate RC operation press and hold the green button on the
remote control and select RC inhibition OFF.
I Child Lock
You can prevent unwanted operation of the LCD monitor via the
buttons on the rear of the monitor.
Select using the 5 or 6 button. Press the 1 button to select
On or OFF.
I Address
Set the address for the LCD monitor.
I Baud rate
Select Baud rate using the 5 or 6 button. To set the
transmission speed for PJ-NET communication of 19200 or 9600
Baud rate by pressing the 1 or 2 button.
I Panel Protect Rotation
Select Panel Protect Rotation using the 5 or 6 button, once
highlighted you can select ON or OFF by pressing the 1 or 2
button.
I AV Auto shut off
Select AV Auto Shut Off using the 5 or 6 button, once
highlighted you can select On or Off by pressing the 1 or 2
button.
I LED Light setting
Select LED Light setting usinig the 5 or 6 button, once
highlighted you can select On or Off by pressing the 1 or 2
button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
OPERATION
Selecting of picture size
Select screen size among “Full”, “Zoom”, “Zoom(Caption-IN)”,
“Normal” and “Natural wide” by pressing WIDE button on the Remote
Control.
I Zoom
I Full
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
enjoying a letter box mode picture (4 : 3 aspect picture with black
bar on top and bottom edges) with wide video aspect of 16 : 9
screen.
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for enjoying a squeezed video
signal with wide video aspect ratio of 16 : 9 screen.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select “Full” to provide better quality.
I Normal
I Zoom (Caption-IN)
Provides the image that is expanded as “Zoom” mode and moved up
to show more image to include captions. This function can be used
for enjoying a letter box picture with captions.
Provides real 4 : 3 image on 16 : 9 screen.
I Natural wide
Provides image to fit width of screen by expanding up/down/left/right
of image. This function is suitable to enjoy a normal video signal (4 :
3 aspect ratio) with wide video aspect ratio of 16 : 9 screen.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
OPERATION
PIP/POP Operation
Using this function, you can enjoy a DVI or Network program and
an image (AV1, AV2, AV3 or PC input) at the same time.
Press the ON/OFF button on the Remote Control repeatly to select
PIP1, PIP2, POP or OFF mode.
During the PIP/POP mode, press the Main/Sub Picture Swap
button will switch the location for main and sub picture.
i Only the sound on the main picture is heard from the monitor
speaker. The sound on the sub-picture cannot be heard.
i The details for PIP/POP operation (eg,location for sub picture or
input source for any picture,etc.), please refer to page 9.
I PIP2 mode
I PIP1 mode
I POP mode
I OFF mode
The left picture is main picture, the right picture is sub picture.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
SPECIFICATIONS / HELPFUL HINTS
Specification
Common specification
Power source
Colour system
120V 50Hz / 60Hz
PAL / NTSC / NTSC4.43/ SECAM
AV terminal
AV1: Scart CENELEC Standard
Input: Composite video, RGB (5V RGB with 5V sync to
pin 14) and audio-L/R
Output: composite video and audio L/R
AV2: BNC
Input: RGB, H and V / Y, Pb, Pr and audio L/R
Output: RGB, H and V / Y, Pb, Pr
AV3: BNC
Input: Composite video
Output : Composite video
DVI
PC
Input :
Input:
DVI-D GROUP Standard
Mini D-SUB 15 PIN and
Audio 3.5mm Jack
Net Organiser: POA-PN03C (optional)
When ordering these products, give the Name and Type No. to the
sales dealer.
Contrast Ratio
1500:1
Screen(inches/ cm)
(viewing measured
diagonally)
52”/132cm
Display Native Resolution
Viewing angles
1920X1080
H:89°, V:89°
Dimensions (WxHxD)
Weight (kg)
1304 x 800 x 234mm
68
Helpful hints
I NO PICTURE
G Check if monitor is plugged in.
G Check monitor is not in standby mode
I POOR PICTURE
G Adjust BRIGHTNESS/ CONTRAST LEVELS (too low).
I NO COLOUR, PICTURE OK
G Adjust COLOUR control.
G Check lead connections
G Does the signal input have colour
I REMOTE CONTROL DOES NOT WORK
G Check batteries are inserted correctly
G Check condition of batteries
G Check to see if remote control inhibit is set ON
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
PC/DVI-D / COMPONENT SIGNAL SUPPORT TIMING LIST
1152_900
1152_900
1152_900
65.20
66.00
75.60
61.20
61.85
SXGA
71.40
MAC_Normal 21”
Mac_.
1280_1024
Horizontal
Frequency
(kHz)
31.43
37.86
37.5
34.97
35
35.16
37.88
46.875
49.72
48.36
60.23
56.47
60.24
68.68
63.98
31.7
Vertical
Frequency
(Hz)
Resolution
Remark
640_480
640_480
640_480
640_480
640_480
800_600
800_600
800_600
832_624
1024_768
1024_768
1024_768
1024_768
1152_870
1280_1024
720_480
59.88
VGA VESA 60Hz
VGA VESA 72Hz
VGA VESA 75Hz
MAC LC 13"
72.81
75
66.6
66.67
56.25
60.32
75
74.55
60
75.03
70.07
75.08
75.06
60.02
59.94
MAC_ NORMAL 13"
SVGA VESA 56Hz
SVGA VESA 60Hz
SVGA VESA 75Hz
MAC_ NORMAL 16"
XGA VESA 60Hz
XGA VESA 75Hz
XGA VESA 70Hz
MAC_ NORMAL 19"
MAC_ NORMAL 21"
SXGA VESA 60Hz
480p
720_480
15.73
59.94
480I
768_575
31.25
50
575p
7
6
8
_
5
7
5
1
5
.63
5
0
5
7
5
I
720p-50Hz
1280_720
45
60
1280_720
37.5
50
720p-60Hz
1
1366_768
48.36
60
60
WXGA
WXGA
1360_768
47.7
1
1920_1080
1920_1080
1920_1080
1920_1080
1920_1080
1920_1080
1920_1080
28.125
33.75
56.25
67.5
50
60
50
60
24
25
30
1080i-50Hz
1080i-60Hz
HDTV1080p-50Hz
HDTV1080p-60Hz
HDTV1080p-24Hz
HDTV1080p-25Hz
HDTV1080p-30Hz
27.00
28.13
33.75
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 1KA6P1P0391--
Printed in U.K.
Download from Www.Somanuals.com. All Manuals Search And Download.
|