INSTRUCTION MANUAL
MCD-ZX540F
MCD-ZX541F
CD Portable Radio Cassette Recorder
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
1
2009.4.8 10:11:04 AM
CONTROLS
1
2
3 4
15
14
19
18
17
20
21
16
5
13
12
6
11
7
10
9
8
25
26
ST
MONO
FM MODE
BEAT CANCEL
24
23
22
27
28
29
1. Headphones socket (PHONES)
2. CD Compartment Lid
3. Tuning control (TUNING)
4. Band select switch (BAND)
5. Frequency indicator
6. Record button (REC)
7. Play button (PLAY)
8. Rewind button (REW)
19. Repeat button (REPEAT)
20. Skip/Search up button
(SKIP/SEARCH e)
21. Play/Pause button (PLAY/PAUSE i)
22. Power indicator (POWER)
23. Cassette holder
24. Display
25. FM mode/Beat cancel switch
(FM MODE/BEAT CANCEL)
26. Telescopic aerial
27. Line in socket (LINE IN)
28. AC input socket (AC INPUT~)
29. Battery compartment lid
9. Fast forward button (F. FWD)
10. Stop/Eject button (STOP/EJECT)
11. Pause button (PAUSE)
12. Bass expander button (BASSXPANDER)
13. Surround button (SURROUND)
14. Volume control (VOLUME)
15. Function switch (CD, RADIO, LINE IN, TAPE/
OFF )
16. Stop button (STOP n)
17. Skip/Search down button
(SKIP/SEARCH f)
18. Memory (MEMORY)
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
2
2009.4.8 10:11:08 AM
POWER SUPPLY
Caution on batteries
AC Power
Connect one end of the mains lead to the AC
INPUT ~ socket and the other end to an AC outlet.
To prevent battery electrolyte leakage, which may
result in injury and damage to the unit or other
objects, observe the following precautions:
1. All batteries must be installed with the proper
polarity (see diagram on the rear of the unit).
2. Do not mix new with old or used batteries.
3. Only use batteries of the same type and
brand.
Note:
-
The installed batteries are automati-
cally disconnected when the mains lead is
connected to the unit.
-
The FUNCTION switch is mounted on
the secondary side. The unit is not discon-
nected from mains, even switched off.
4. Remove the batteries when they are not to be
used for a long period time.
5. When the batteries have become discharged,
they must be disposed of in a safe manner
which complies with all applicable laws.
6. Batteryshallnotbeexposedtoexcessiveheat
such as sunshine, fire or the like.
Battery power
Installing batteries
Install eight “D/HP2/R20” batteries (not sup-
plied) as shown below.
1.
2.
3.
7
3
8
4
OPEN
OPEN
6
2
5
1
GENERAL OPERATION
Adjusting the volume
Turn the VOLUME control.
Headphones
Connect stereo headphones (not supplied) to the
PHONES socket for monitoring or for private
listening. The speakers are automatically
disconnected when headphones are connected.
Bass expander button
Press the BASSXPANDER button to Z ON to
enhance the bass sound.
-
Excessive sound pressure from earphones
and headphones can cause hearing loss.
Surround sound button
Press the SURROUND button to Z ON, a 3
dimensional sound effect is created.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
3
2009.4.8 10:11:12 AM
CD PLAY
Use compact discs bearing the symbol shown
Note:
below. In addition to conventional 12cm CDs,
this system can be used to play 8cm CDs without
an adapter.
Do not open the CD compartment during CD play.
Always press the STOP n button and wait for
the disc to stop rotating before opening the CD
compartment.
This unit can play back the CD-R/RW as well.
However, some CD-R/RW can not be played back
depending on the recording conditions.
1. Set the FUNCTION switch to CD. “--” blinks
for several seconds then the CD mode ap-
pears.
2. Press the CD compartment lid (OPEN/ CLOSE
portion) to open it. “00” appears on the dis-
play.
3. Place the disc with the label facing up on the
turntable as shown below. (Place only one
disc at a time.)
Notes on handling compact discs
-
Do not expose the disc to direct sunlight,
high humidity or high temperature for ex-
tended periods of time.
-
-
-
-
Discs should be returned to their cases after
use.
Do not apply paper or write anything on the
disc surface.
Handle the disc by its edge. Do not touch
the playing surface (glossy side).
Fingerprints and dust should be carefully
wiped off the playing surface of the disc
with a soft cloth.
Wipe in a straight motion from the center to
the outside of the disc.
-
Never use chemicals such as record clean-
ing sprays, antistatic sprays or fluids, ben-
zene or thinner to clean compact discs.
4. Press the CD compartment lid (OPEN/ CLOSE
portion) to close it.
The total number of tracks on the disc appears
on the display.
5. Press the PLAY/PAUSE i button.
Temporarily stopping play
Press the PLAY/PAUSE i button, “a” blinks
on the display. To resume play, press the button
again.
Skip play
To skip to track 6 while track 3 is playing, press the
ebutton repeatedly until “6” appears on the
display. To skip back to track 3 while track 6
is playing, press the f button repeatedly until
“3” appears.
The current track number appears. Play starts from
the first track.
-
To start play from the desired track, select the
track by using the f or e button, then
press the PLAY/PAUSE ibutton.
Note:
Search (forward/reverse)
If no disc is loaded or the disc is located with the
label facing down “00” appears. If these occur,
load the disc correctly or replace the damaged
disc.
If the e or fbutton is pressed during play,
the player will search at high speed in the forward
or reverse direction while the button is being
pressed. When the button is released, normal play
will continue.
6. Press the STOP n button to end disc play
back.
When the last track has been played, the player
stops automatically.
7. To turn the CD player off, set the FUNCTION
switch to TAPE/OFF .
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
4
2009.4.8 10:11:15 AM
5. Repeat steps 3 - 4 to programme addition-
al tracks.
6. Press the PLAY/PAUSE ibutton to start
playback. “MEMORY” remains lit.
Repeat playing mode
Press the REPEAT button repeatedly to select
a repeat play mode available. Each time the
button is pressed, the mode changes as shown
below:
[CD]
MEMORY
“REPEAT” blinks
(Repeat one track)
“REPEAT” appears
(Repeat all tracks)
When all programmed tracks have been
played, the player stops automatically.
-
The programme contents are retained
in memory.
Released
(Normal play)
-
-
Any attempt to programme more than 20
tracks will result in discontinuous of the
programming.
To cancel programmed play, press the STOP
n button twice during play.
PROGRAMMED PLAY
Up to 20 tracks on a disc can be programmed for
play in any order.
Checking the programme
-
-
-
To begin the programming procedure, set
function switch to “CD” first.
The same track can be programmed more
than once.
Load a disc that you want to programme be-
fore starting programmed play.
In stop mode when MEMORY remains lit
press the MEMORY button once, the pro-
grammed details sequentially appear on the
display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY but-
ton repeatedly until last programme number
is displayed.
1. Press the STOP nbutton if necessary.
2. Press the MEMORY button, the “01” and
“MEMORY” blink.
2. Select a track as explained above.
3. Press the MEMORY button.
MEMORY
To change a track:
1. In the stop mode, press the MEMORY button
repeatedly until the programme number to be
replaced is displayed.
3. Select a track by using the f or e but-
ton.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
MEMORY
Programmed details cannot be partially deleted
or inserted.
4. Press the MEMORY button.
WHAT TO DO IF...
MEMORY
If an abnormal display indication or an operating
problem occurs, disconnect the mains lead and
remove all batteries. Wait at least 5 seconds then
reconnect the mains lead and reinstall the batteries.
Resume the operation.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
5
2009.4.8 10:11:18 AM
LISTENING TO OTHER SOURCES
1. Connect the audio cable (not supplied)
2. Set the FUNCTION switch to LINE IN.
3. Follow the instructions supplied with the other
equipment.
from the audio output socket of a auxiliary
equipment to the LINE IN socket. (Stereo
Mini Plug: ø3.5)
Auxiliary equipment
LISTENING TO TAPES
1. Set the FUNCTION switch to TAPE/OFF.
2. Press the STOP/EJECT button. The cassette
holder opens.
Pause
Press the PAUSE button to temporarily stop
playback or recording. Press it again to resume
operation.
3. Load the cassette into the cassette holder.
Fast forward and rewind
Press the F. FWD or REW button. When the
desired location has been reached, or the tape
has been wound to the end, press the STOP/
EJECT button.
Automatic stop system
At the end of the tape while recording or playing
back, the cassette deck stops automatically and
the buttons are released.
After loading the cassette, push the cassette
holder back into position.
This system does not work in fast forward and
rewind operation. Be sure to press the STOP/
EJECT button when the end of the tape has been
reached.
4. Press the PLAY button to begin playback.
5. Press the STOP/EJECT button to stop
playback at any time. Press it again to remove
the cassette.
Example (When using C-60 tape):
When the end of the tape has been reached
the tape stops automatically.
Press the STOP/EJECT button after approxi-
mately 2 minutes have elapsed under fast for-
ward and rewind operation.
Note:
-
-
-
Use the normal tape (TYPE 1).
Endless tapes cannot be used.
Do not use C-100 (or longer) tapes. They
may jam in the mechanism.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
6
2009.4.8 10:11:20 AM
LISTENING TO THE RADIO
1. Set the FUNCTION switch to RADIO.
2. Select the desired radio band with the BAND
switch.
To improve reception
FM: Pull out the telescopic aerial and adjust
its position.
3. Tune in a desired station by turning the
TUNING control.
AM: Rotate the unit.
4. To turn the radio off, set the FUNCTION
switch to TAPE/OFF or CD or LINE IN.
To receive FM stereo broadcasts
Set the FM MODE select switch (the back of the
unit) to ST.
-
If the signal from an FM stereo station is weak
and reception is poor, set the FM MODE
select switch to MONO. The reception may be
improved, but the sound will be monaural.
RECORDING
Recording copyright material without permission
of the copyright owners is usually an infringement.
If you wish to re-record copyright material,
permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held
responsible for, any unlawful use of this machine.
When beat is heard
Beat (a high-pitched noise) may sometimes be
heard during the recording of radio broadcasts.
If this occurs, set the BEAT CANCEL switch (the
back of the unit) to 1 or 2 position that reduces
the level of the beat noise.
Recording from CD (Synchronous
recording)
1. Load a blank cassette.
2. Set the FUNCTION switch to CD.
3. Load a CD to be recorded.
Safeguards against accidental erasure
To protect side A, break out tab (1). To protect
side B, break out tab (2).
-
To erase or record a protected cassette, cover
the tab openings with adhesive tape (3).
-
-
Select the track if required.
For programmed recording, pro-
gramme the material in advance.
Note:
The REC button cannot be depressed when using
a protected cassette.
4. Press the REC button. The PLAY button
is engaged simultaneously and recording
starts.
5. Press the STOP/EJECT button to stop
recording at any time. When the end of the
tape is reached, deck stop automatically and
the playback of CD enters stop mode.
Recording from the radio or other sources
1. Load a blank cassette.
2. Tune in the radio station to be recorded or play
other sources.
3. Press the REC button to start recording.
4. Press the STOP/EJECT button to stop
recording.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
7
2009.4.8 10:11:22 AM
MAINTENANCE
Cleaning the tape heads
Cleaning the unit
To ensure continued high performance, use a
cleaning tape (available from your local audio
dealer) to clean the head block of the deck after
about every 10 hours of use.
Clean the outside of the unit with a clean soft
cloth, moistened with lukewarm water. Do not
use benzene, thinners, or alcohol for they may
mar the finish of the surfaces.
Cleaning the CD player lens
The lens should never be touched. If dust is on
the lens, blow it off using a camera lens blower.
(Consult your dealer.)
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
8
2009.4.8 10:11:23 AM
SPECIFICATIONS
CD player
Channels:
General
Output power:
2-Channel stereo
2 W/ch (DC max.)
1.5 W/ch (AC max.)
Speakers:
10 cm x 2, 8 ohms
Terminals:
PHONES: 32 ohms
Power source:
Sampling frequency:
44.1 KHz
Pick-up:
Semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
AC: 230 - 240V, 50Hz
DC: 12V, 8 “D/HP2/R20” batteries
Wow/Flutter:
Dimensions:
390 (W) x 165 (H) x 260 (D) mm
Weight:
Below measurable limits
Radio
Approx. 2.4 kg (not including batteries)
Reception frequency:
FM: 87.5 - 108 MHz
AM: 526.5 - 1606.5 KHz
Specifications subject to change without notice.
Cassette deck
Track system:
4-track, 2-channel stereo
Erasing system:
Magnet erase
Tape speed:
4.75 cm/sec.
Frequency response:
80 - 12,000 Hz
Fast forward/rewind time:
Approx. 110 sec. (C-60)
SANYO Electric Co., Ltd.
Printed in China
(AU) MR601X68000030
Download from Www.Somanuals.com. All Manuals Search And Download.
540AU.indd
9
2009.4.8 10:11:24 AM
|