Multimedia Projector
PLC-XP55/XP56
MODEL
PLC-XP55L/XP56L (Lensless)
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: PLC-XP55/PLC-XP56/PLC-XP55L/PLC-XP56L
: Sanyo
: SANYO FISHER COMPANY
: 21605 Plummer Street, Chatsworth, California 91311
: (818)998-7322
Telephone No.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of
the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating,
ASA
marked thus
. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse
cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse
covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING : THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
7
COMPUTER INPUT
23
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
23
23
25
25
26
PREPARATION
PC ADJUSTMENT
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
NAME OF EACH PART OF PROJECTOR
7
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
POSITIONING PROJECTOR
8
PICTURE IMAGE SELECT
28
8
IMAGE LEVEL SELECT
28
9
PICTURE SCREEN ADJUSTMENT
29
ADJUSTABLE FEET
INSTALLING PROJECTOR IN PROPER POSITION
MOVING PROJECTOR
10
10
11
VIDEO INPUT
30
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
30
31
CONNECTING PROJECTOR
12
PICTURE IMAGE SELECT
32
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
12
13
14
IMAGE LEVEL SELECT
32
PICTURE SCREEN ADJUSTMENT
33
PICTURE IMAGE
34
BEFORE OPERATION
15
PICTURE IMAGE ADJUSTMENTS
34
OPERATION OF REMOTE CONTROL
LASER POINTER FUNCTION
15
15
16
SETTING
37
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
17
SETTING MENU
37
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
18
18
18
19
APPENDIX
41
OPERATING WIRELESS MOUSE
MAINTENANCE
41
BASIC OPERATION
20
42
42
43
43
44
45
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP REPLACEMENT
TURNING ON / OFF PROJECTOR
20
ADJUSTING SCREEN
21
21
21
21
21
22
22
22
ZOOM ADJUSTMENT
LAMP REPLACE COUNTER
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
TROUBLESHOOTING
46
48
49
50
52
53
54
54
INDICATORS AND PROJECTOR CONDITION
COMPATIBLE COMPUTER SPECIFICATION
MENU TREE
P-TIMER FUNCTION
TECHNICAL SPECIFICATIONS
CONFIGURATIONS OF TERMINALS
OPTIONAL PARTS
SOUND ADJUSTMENT
22
LENS REPLACEMENT
TRADEMARKS
G Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
G IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
G Windows and PowerPoint are registered trademarks of Microsoft Corporation.
G Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
N Compact Design
N Digital Zoom (for Computer)
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.
N Keystone Correction
N Compatibility
Positioning of a projector may result in distorted image
being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
This projector widely accepts various video and
computer input signals including;
G Computers
IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.
N Power Management
G 6 Color Systems
Power Management function is provided to reduce power
consumption while a projector is not in use.
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed. Projection
Lamp is automatically turned on again when a projector
detects signal or any operation button is pressed.
This projector is shipped with this function ON.
G Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
G S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
N Digital Visual Interface
This projector is equipped with DVI 24-pin terminal for
connecting DVI output from a computer.
N High Resolution Image
N Laser Pointer Function
This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and SXGA
(1280 x 1024) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1280 x 1024 dots.
When resolution of your computer is over than 1280 x
1024, reset a computer output for lower resolution.
Remote Control Unit supplied with this projector includes
Laser Pointer function. This function helps you to make
a smart presentation on a projected screen.
N Wireless Mouse
Remote Control Unit supplied with this projector has
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with Remote Control Unit only.
N Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
N Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.
N One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
N PJ-Net Organizer (Optional)
PJ-Net Organizer enables the projector to display the
image of the computer screen and the data image stored
in the computer via a network. The projector can be also
controlled and maintained through a web browser.
N Motor-driven Lens Shift
Projection lens can be moved up and down with motor-
driven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT OF CABINET
TOP CONTROLS
AND INDICATORS
PROJECTION LENS
AIR INTAKE
VENT
INFRARED
REMOTE RECEIVER
LENS COVER
SPEAKERS
BACK OF CABINET
EXHAUST VENT
TERMINALS
AND CONNECTORS
INFRARED
REMOTE RECEIVER
POWER CORD
CONNECTOR
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
G Do not put a flammable object near this vent.
G Keep rear grills at least 3.3’(1 m) away from
any object, especially heat-sensitive object.
G Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
CARRYING
HANDLE
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
LAMP COVER
When attached the PJ-Net organizer (optional
part) to the projector, remove the these parts.
Refer to the owner's manual in the optional
PJ-Net organizer.
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protection from
overheating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.
G Do not cover vent slots.
G Keep side clear of any objects. Obstructions may block cooling
air.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on. (Refer to pages 12 ~ 14 for connection.)
CAUTION
For safety, unplug AC Power Cord when an appliance is not
used.
Connect AC Power Cord (supplied) to a projector.
AC outlet must be near this equipment and must
be easily accessible.
When this projector is connected to outlet with AC Power Cord,
an appliance is in Stand-by Mode and consumes a little electric
power.
NOTE ON POWER CORD
AC Power Cord must meet requirement of country where you use a projector.
Confirm an AC plug type with chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada For Continental Europe
For the U.K.
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(200 - 240 V AC)
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200 - 240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
POSITIONING PROJECTOR
NOTE: The figures below are only for Model PLC-XP55/PLC-XP56.
Projection lens is not provided with Model PLC-XP55L/PLC-XP56L.
G This projector is designed to project on a flat
ROOM LIGHT
Brightness in room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide best
image.
projection surface.
G Projector can be focused from 4.6’ (1.4m) ~ 48.3’
(14.7m).
G Refer to figure below to adjust screen size.
48.3’(14.7m)
36.1’(11.0m)
400”
Max. Zoom
Min. Zoom
24.0’(7.3m)
300”
11.8’(3.6m)
4.6’(1.4m)
308”
200”
231”
100”
154”
40”
31”
77”
Max. Zoom
Min. Zoom
40”
31”
100”
77”
150”
200”
250”
300”
231”
400”
Screen
Size
154”
192”
308”
115”
4.6’ (1.4m)
11.8’ (3.6m)
17.7’ (5.4m)
24.0’ (7.3m)
30.2’ (9.2m) 36.1’ (11.0m) 48.3’ (14.7m)
Distance
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer
to P 21 for operation.
Highest (10 : 0)
Lowest (1 : 1)
1
1
10 : 0
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.
Lift front of a projector and pull FEET LOCK LATCHES
on both sides of a projector.
1
Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.
2
To shorten ADJUSTABLE FEET, lift front of a projector
and pull and undo FEET LOCK LATCHES.
3
Position and keystone distortion of image can be adjusted
using Menu Operation. (Refer to P 21 and 37.)
ADJUSTABLE FEET
FEET LOCK
LATCHES
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.
10˚
Do not tilt the projector more than 10 degrees above and below.
10˚
Do not point the projector up to project an image.
NO UPWARD
Do not point the projector down to project an image.
NO DOWNWARD
Do not put the projector on either side to project an image.
NO SIDEWAYS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING PROJECTOR
Use Carry Handle when moving a Projector.
When moving a projector, replace lens cover and retract
feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (dust cover) supplied with this projector.
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
G Do not drop or bump a projector, otherwise damages or malfunctions may result.
G When carrying a projector, use a suitable carrying case.
G Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer for best way.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 12 to 14 and connect properly.
COMPUTER INPUT/MONITOR
OUTPUT TERMINAL (ANALOG)
COMPUTER AUDIO
INPUT 2 JACK
Connect an audio output
(stereo) from computer to
this jack.
COMPUTER AUDIO
INPUT 1/AUDIO MONITOR
OUTPUT JACK
COMPUTER INPUT
TERMINAL (DIGITAL)
This terminal is switchable and
can be used as computer input or
monitor output. Set the terminal up
as either Computer input or
Monitor output properly before
using this terminal.
Connect computer output
(Digital DVI-D type) to this
terminal.
HD (HDCP Compatible) signal
can also be connected.
Refer to P13.)
This terminal is switchable
and can be used as computer
audio input 1 or audio monitor
output (variable).
Set the terminal up as either
Computer audio input 1 or
Audio Monitor output properly
before using this terminal.
Refer to P13, P23.)
(Refer to P13.)
Refer to P13, P23.)
Note; This terminal outputs from 5
BNC type computer input on
INPUT 2 jacks only.
R/C JACK
When using Wired/Wireless
Remote Control Unit as Wired
Remote Control, Connect
Wired Remote Control Unit to
this jack with Remote Control
Cable (supplied).
INPUT 1
DIGITAL(DVI-D)
ANALOG IN/OUT
R/C JACK
USB CONNECTOR (Series B)
CONTROL PORT
RESET
AUDIO 1
IN/OUT
USB
AUDIO 2
When controlling computer with
Remote Control Unit of this
projector, connect USB terminal
of your personal computer to
this terminal. (Refer to P13.)
CONTROL PORT CONNECTOR
G
B
R
H/V
V
When controlling computer
with Remote Control Unit of
this projector, connect mouse
port of your personal computer
to this connector. (Refer to
P13.)
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
RESET BUTTON
This projector uses a micro processor
to control this unit, and occasionally,
this micro processor may malfunction
and need to be reset. This can be
done by pressing RESET button with a
pen, which will shut down and restart
unit. Do not use RESET function
excessively.
(
)
MONO
INPUT 3
✽ Do not press this button. This button
is used for our optional accessories.
VIDEO INPUT JACKS
AUDIO INPUT JACKS
S-VIDEO INPUT JACK
Connect composite video Connect an audio output Connect S-VIDEO
output from video equipment from video equipment to output from video
5 BNC INPUT JACKS
to VIDEO/Y jack or connect these jacks.
component video outputs to (Refer to P14.)
VIDEO/Y, Cb/Pb and Cr/Pr
equipment to this
jack. (Refer to P14.)
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
(Refer to P13 and 14.)
jacks. (Refer to P14.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (✽ = Cable or adapter is not supplied with this projector.)
• VGA Cable (HDB 15 pin)
• Control Cable for PS2 Port ✽, or ADB Port ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• BNC Cable ✽
• Control Cable for Serial Port
• USB Cable
• MAC Adapter (When connecting to Macintosh computer) ✽
• Audio Cables (Mini Plug (stereo) x 2) ✽
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor Output
ADB port
USB port
Monitor Output
Audio Output
PS/2 port
Monitor Output
Serial port
or
Monitor Input
Control Cable
for ADB Port ✽
USB
Cable
Control Cable
for PS/2 Port ✽
Control Cable
for Serial Port
Audio
Cable ✽
MAC Adapter ✽
DVI
Set slide switches
according to chart
below.
Cable ✽
(stereo)
Terminal
Terminal
Terminal
BNC
Cable ✽
VGA Cable
COMPUTER
AUDIO IN 1 or 2
Use one of these Control
Cables corresponding with
terminal of your computer.
USB
COMPUTER IN ANALOG
COMPUTER IN DIGITAL
CONTROL
PORT
INPUT 1
DIGITA(DVI-D)
ANALOIN/OUT
R/C JACK
NOTE;
This terminal is switchable.
CONTROL PORT
RESET
USB
AUDIO 1
IN/OUT
Set the terminal up as either
Computer audio input 1 or audio
monitor output (variable) before using
this terminal. (See page 23.)
AUDIO 2
NOTE;
AUDIO OUT
This terminal is switchable.
Set the terminal up as
either Computer input or
Monitor output before
using this terminal.
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(See page 23.)
Audio Cable
(stereo) ✽
(
)
MONO
NOTE :
INPUT 3
Terminals
When connecting cable, power cords
of both a projector and external
equipment should be disconnected
from AC outlet. Turn a projector and
peripheral equipment on before
computer is switched on.
of a Projector
N MAC ADAPTER ✽
Set switches as shown in table
below depending on RESOLU-
TION MODE that you want to
use before you turn on projec-
tor and computer.
Audio Input
ON
ON
DIP
External Audio Equipment
1
2
3
4
5
6
Audio Speaker
(stereo)
OFF
3
Audio Amplifier
1
2
4
5
6
13" MODE (640 x 480)
ON
ON OFF OFF OFF OFF
16" MODE (832 x 624) OFF ON OFF ON OFF OFF
19" MODE (1024 x 768) OFF ON
21" MODE (1152 x 870) ON ON
ON OFF OFF OFF
ON ON OFF OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection (✽ = Cable is not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• Audio Cable {Mini Plug (stereo)} ✽
• Scart Cable ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x 2) ✽
Video Source (example)
Component video output equipment.
(such as DVD player or high-definition TV source.)
Video Cassette Recorder
Video Disc Player
Audio Output S-VIDEO
Output
Component Video
RGB Scart
21-pin Output Video Output
Composite Component Video
Composite
Video Output
Output
Output
(Y, Cb/Pb, Cr/Pr)
(Y, Cb/Pb, Cr/Pr)
Video Cables
(RCA x 1 or
RCA x 3) ✽
Scart Cable ✽
Audio Cable
(RCA x 2) ✽
S-VIDEO
Cable ✽
BNC Cable ✽
VIDEO
VIDEO
Y - Cb/Pb - Cr/Pr
Y - Cb/Pb - Cr/Pr AUDIO IN
S-VIDEO
COMPUTER IN ANALOG
INPUT 1
DIGITAL(DVI-D)
ANALOG IN/OUT
R/C JACK
CONTROL PORT
AUDIO 1
IN/OUT
RESET
USB
AUDIO OUT
AUDIO 2
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
Audio Cable
(stereo) ✽
(
)
MONO
INPUT 3
NOTE;
This terminal is switchable.
Set the terminal up as either
Computer audio input 1 or audio
monitor output (variable) before
using this terminal.
Terminals
of a Projector
(See page 23.)
Audio Input
NOTE :
External Audio Equipment
Audio Speaker
When connecting cable, power cords of
both a projector and external equipment
should be disconnected from AC outlet.
Audio Amplifier
(stereo)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
LASER POINTER (Drag ON)
INDICATOR
Lights red while laser beam
is emitted from Laser Light
Window.
Left Side
POWER ON-OFF BUTTON
Used to turn projector on or
off. (P20)
AUTO PC ON-OFF
Lights green when drag ON
position. (P41)
D.ZOOM FREEZE NO SHOW
AUTO PC ADJ. BUTTON
Use to operate AUTO PC
Adjustment function. (P25)
MUTE
IMAGE
MUTE BUTTON
VOLUME
-
VOLUME+
SELECT
Used to mute sound. (P22)
IMAGE BUTTON
Used to select image
level. (P28, 32)
MENU
KEYSTONE
DRAG ON/OFF BUTTON
Used to select drag ON/OFF
position. (P41)
ALL-OFF SWITCH
KEYSTONE BUTTON
Used to correct keystone
distortion. (P21, 37)
When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.
LEFT CLICK BUTTON
Used as a PC mouse in
Wireless Mouse Operation.
Press this button and the
mouse pointer button to drag
a selected screen object.
(P41)
INSIDE THE BATTERY
COMPARTMENT BOX
This remote control provide the DIP
switches into the battery compartment
box.
Slide the SW4 (LASER ON/OFF
switch) to "OFF" position. The laser
pointer function is not operated.
Set switches 1-3 as shown in table
below depending on Code No. that you
want to select remote control code.
(Refer to P39.)
MOUSE POINTER
Used as a PC mouse in
Wireless Mouse Operation.
(P41)
LASER
P-TIMER
COLOR.M
RIGHT CLICK BUTTON
LASER BUTTON
INPUT
INPUT
1
Used as a PC mouse in
Wireless Mouse Operation.
(P41)
Used to operate Laser Pointer
Function. Laser beam is
emitted while pressing this
button within 1 minute.
ZOOM
2
When using this Laser Pointer
INPUT
3
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P21)
for more than
1
minute,
release LASER button and
press it again.
NETWORK
FOCUS LENS
DIP SWITCH SETTING
SW4 ........ LASER ON/OFF
SW1 SW2 SW3 Code No.
WIRED REMOTE JACK
ON
ON
ON
ON
ON
OFF ON
ON
Code 1
Code 2
Code 3
FOCUS BUTTON
Used to adjust focus. (P21)
When using as Wired
Remote Control, connect
Remote Control Cable to
this jack.
Battery installation is
required when using as
Wired Remote Control.
OFF
ON
OFF OFF
Code 4
Code 5
Code 6
Code 7
Code 8
OFF ON
OFF ON
ON
OFF
OFF OFF ON
OFF OFF OFF
LASER POINTER FUNCTION
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other
people. Three marks below are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result
hazardous radiation exposure.
These caution labels are put on remote control.
LASER POINTER INDICATOR
Laser Light Window
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
NO SHOW BUTTON
Used to turn picture into
black image. (P22)
D.ZOOM BUTTON
Operating Range
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P29)
Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.
AUTO PC ON-OFF
D.ZOOM FREEZE NO SHOW
SELECT BUTTON
MUTE
IMAGE
FREEZE BUTTON
Used to freeze picture. (P22)
Used to execute the
selected item, or to
expand or compress
image in DIGITAL ZOOM
+/- mode. (P29)
VOLUME
-
VOLUME+
SELECT
POINT (VOLUME +/-)
BUTTONS
MENU
KEYSTONE
Used to select an item or
adjust value in ON-SCREEN
MENU. They are also used
to pan image in DIGITAL
ZOOM +/- mode. (P29)
POINT LEFT/RIGHT buttons
are also used as VOLUME
+/- buttons. (P22)
60°
MENU BUTTON
Used to select MENU
operation. (P18, 19)
16.4’
(5 m)
INPUT 1 BUTTON
P-TIMER BUTTON
Used to select input
source (INPUT 1).
(P23)
LASER
P-TIMER
COLOR.M
Used to operate P-
TIMER function. (P22)
INPUT
INPUT
1
INPUT 2 BUTTON
ZOOM
2
Used to select input
source (INPUT 2).
(P24, 30)
ZOOM BUTTON
INPUT
3
Used to adjust zoom. (P21)
NETWORK
FOCUS LENS
INPUT 3 BUTTON
16.4’
(5 m)
Used to select input
source (INPUT 3).
(P30)
COLOR MANAGEMENT
BUTTON
60°
Used to operate COLOR
MANAGEMENT.
(P34)
NETWORK BUTTON
Used to select network
input. (Option)
Remote Control Batteries Installation
Remove battery
compartment lid.
Slide batteries into
compartment.
Replace compartment lid.
1
2
3
Two AA size batteries
Press lid down-
ward and slide it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
G Use (2) AA, UM3 or R06 type alkaline batteries.
G Replace two batteries at same time.
G Do not use a new battery with an used battery.
G Avoid contact with water or liquid.
G Do not expose Remote Control Unit to moisture, or heat.
G Do not drop Remote Control Unit.
G If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
G Danger of explosion if battery is incorrectly replaced.
G Dispose of used batteries according to batteries manufacturers instructions and local rules.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns to yellow when
life of projection lamp
draws to an end. (P44)
Flashes red when
Lights green when a
projector is ready to be
Becomes dim when a
projector is turned on.
And bright when a
projector is in stand-by
mode.
internal
projector
temperature is too
high. (P42)
turned on.
And it
flashes green in Power
Management mode.
(P39)
POWER ON–OFF BUTTON
Used to turn a projector
on or off. (P20)
MENU BUTTON
Used to open or close
MENU operation. (P18,
19)
INPUT BUTTON
Used to select input
source. (P23, 24, 30)
ZOOM BUTTON
Used to adjust zoom.
(P21)
FOCUS BUTTON
Used to adjust focus.
(P21)
AUTO PC ADJ. BUTTON
Used to operate AUTO PC
Adjustment function. (P25)
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P21)
IMAGE BUTTON
Used to select image
level. (P28, 32)
SELECT BUTTON
POINT (VOLUME + / – ) BUTTONS
Used to execute the
selected item.
It is also used to
expand/compress image
in DIGITAL ZOOM mode.
(P29)
Used to select an item or adjust
value in ON-SCREEN MENU. They
are also used to pan image in
DIGITAL ZOOM +/– mode. (P29)
POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
REMOTE CONTROL UNIT
You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
AUTO PC ON-OFF
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
POINT BUTTONS
D.ZOOM FREEZE NO SHOW
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
MUTE
IMAGE
2 MOVING POINTER
Move pointer (✽ see below) or adjust value of item by pressing
VOLUME
-
VOLUME+
SELECT
POINT button(s) on Top Control or on Remote Control Unit.
MENU
KEYSTONE
✽ Pointer is icon on ON-SCREEN MENU to select item. See fig-
ures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.
MENU BUTTON
SELECT BUTTON
Used to select the item.
Used to select the item.
3 SELECT ITEM
Select item or set selected function by pressing SELECT button.
TOP CONTROL
POINT BUTTONS
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
MENU BUTTON
SELECT BUTTON
Used to select item.
FLOW OF ON-SCREEN MENU OPERATION
MENU ICON
MENU BAR
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
1
POINTER (red frame)
POINTER
Press POINT UP/DOWN
button to move POINTER.
(red frame)
Select Menu to be adjusted
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
2
ITEM
Control or adjust item through ON-SCREEN MENU
Press POINT UP/DOWN button and move POINTER (red
frame or red arrow) to ITEM that you want to adjust, and then
press SELECT button to show ITEM DATA.
3
SELECT
BUTTON
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
4
buttons.
Refer to following pages for details of respective
adjustments.
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
SETTING MENU
SCREEN MENU
IMAGE SELECT MENU
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P37-40)
Used to adjust size
of image. [Normal
/ True / Wide /
Digital zoom +/–]
(Refer to P29)
Used to select
PC SYSTEM MENU
GUIDE WINDOW
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P28)
Used to select
computer system.
(Refer to P23, 24)
Shows selected
item of ON-
SCREEN MENU.
PC ADJUST MENU
INPUT MENU
SOUND MENU
IMAGE ADJUST MENU
Used to adjust
parameters to
match with input
signal format.
Used to select
Used to adjust
volume or mute
sound.
Used to adjust computer
image.
[Contrast/Brightness/Color
/Tint/Color management
/Auto picture control
/Color temp.
input source (Input
1, Input 2 or Input
3). (Refer to P23)
(Refer to P22)
(Refer to P25-27)
/White balance (R/G/B)
/Sharpness/Gamma/Noise
reduction/Progressive]
(Refer to P34-36)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
INPUT MENU
Used to select
input source
(Input 1, Input 2
or Input 3).
IMAGE SELECT MENU
SCREEN MENU
Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P32)
Used to set size of
image to Normal
or Wide.
(Refer to P33)
(Refer to P30)
Same function as
Menu for PC source.
AV SYSTEM MENU
IMAGE ADJUST MENU
Same function as
Menu for PC source.
Used to select
system of selected
video source.
Used to adjust picture image.
[Contrast/Brightness/Color/Tint
/Color management
/Auto picture control/Color temp.
/White balance (R/G/B)
(Refer to P31)
/Sharpness/Gamma
/Noise reduction/Progressive]
(Refer to P34-36)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on pages 12~14 for connecting that equipment.)
Input position and
Lamp mode status
1
2
Connect a projector's AC Power Cord into an AC outlet. LAMP
Indicator lights RED, and READY Indicator lights GREEN.
NOTE : When “On start” function is ON, this projector is turned
on automatically by connecting AC Power Cord to an
AC outlet. (Refer to page 39.)
30
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP Indicator dims, and Cooling Fans
start to operate. Preparation Display appears on a screen and
count-down starts. Signal from PC or Video source appears after
30 seconds.
3
Preparation Display disappears after 30 seconds.
Current Input position and Lamp mode status are also displayed
on screen for 5 seconds. (Refer to "LAMP MODE" on page 37.)
TURNING OFF PROJECTOR
Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.
1
2
Press POWER ON-OFF button again to turn off projector. LAMP
Indicator lights bright and READY Indicator turns off. After
projector is turned off, Cooling Fans operate (for 90 seconds).
During this "Cooling Down" period, projector cannot be turned
on.
Message disappears after 4 seconds.
When projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling down
completely, disconnect AC Power Cord.
3
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When “Power Management” function mode is Ready or Shut down, projector detects signal interruption and turns off the
Projection Lamp automatically. Refer to “Power management” on page 39.
When WARNING TEMP. Indicator is flashing, projector cannot be turned on, refer to the section "MAINTENANCE" on page 42.
When the both WARNING TEMP. and READY Indicator flashing, refer to the section "MAINTENANCE" on page 42.
Do not use the projector continuously for 24 hours or more. If using the projector continuously for long periods,
turn it off and leave it for one hour at least once during a 24 hour period.
If you use the projector continuously for long period, it can excessively shorten the life of the lamp.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press ZOOM button on Top Control or ZOOM L/M button on
Remote Control Unit. Message “Zoom” is displayed.
1
2
Press ZOOM L button or POINT UP button to make image
larger, and press ZOOM M button or POINT DOWN button to
make image smaller.
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press FOCUS button on Top Control or FOCUS L/M button on
Remote Control Unit. Message “Focus” is displayed.
1
2
Adjust focus of image by pressing FOCUS L/M button or
POINT UP/DOWN button(s) .
NOTE;
Message disappears after 4 seconds.
Focus adjustment may not function properly if the image is
corrected by KEYSTONE adjustment.
LENS SHIFT ADJUSTMENT
Press LENS SHIFT button on Top Control or LENS SHIFT L/M
button on Remote Control Unit. Message “Lens shift” is
displayed.
1
2
Press POINT UP button or LENS SHIFT L button to move
image up, press POINT DOWN or LENS SHIFT M button to
move image down.
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 37.) Keystone
dialog box appears.
1
Correct keystone distortion by pressing POINT
UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to
reduce the upper part of the image, and press POINT DOWN
button to reduce the lower part. Press POINT LEFT button to
reduce the left part, and press POINT RIGHT button to reduce
the right part.
2
• Arrows are white in no correction.
• Arrow(s) of direction being corrected turn(s) red.
• Arrow(s) disappear(s) at the maximum
correction.
• If you press the KEYSTONE button on Top
Control or on Remote Control Unit once more
while the keystone dialog box is being
displayed, the keystone adjustment will be
canceled.
Reduce the upper width
with POINT UP button.
Reduce the lower width
with POINT DOWN button.
Reduce the left part with
POINT LEFT button.
Reduce the right part with
POINT RIGHT button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button.
Message disappears after 4 seconds.
P-TIMER FUNCTION
Press P-TIMER button on Remote Control unit. Timer display “00 : 00”
appears on screen and timer starts to count time (00 : 00 ~ 59 : 59).
To stop P-TIMER display, press P-TIMER button. And then, press P-
TIMER button again to cancel P-TIMER function.
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button to set
Mute function On or Off.
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Display disappears after 4 seconds.
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon.
SOUND MENU
1
2
Press POINT UP/DOWN button to move a red frame pointer to
item that you want to select, and then press SELECT button.
SOUND Menu icon
Indicates roughly
level of volume.
Volume
Close SOUND Menu.
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.
Built-in SP.
Press POINT LEFT/RIGHT button(s) to switch built-in speaker on and
off.
Mute
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
SELECTING INPUT SOURCE
INPUT button
Input 1
DIRECT OPERATION
✽
Select INPUT source by pressing INPUT button on Top Control.
Select INPUT source by pressing INPUT 1, INPUT 2 or INPUT 3
button on Remote Control Unit.
Input 2
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
Input 3
NOTE
✽
Input 1 is not displayed when the Input 1 is used as
Monitor out.
G Input 1 terminal is switchable and can be used as computer input or
monitor output.
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
1
INPUT Menu icon
Press POINT UP/DOWN button and a red-arrow icon will
appear. Move arrow to INPUT source that you want to select,
and then press SELECT button.
2
SELECTING COMPUTER SYSTEM
WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
1
2
3
Press POINT UP/DOWN button to move a red arrow pointer to
Input 1 and then press SELECT button. Source Select Menu will
appear.
INPUT Menu icon
Move a pointer (red arrow) to
Input 1 and press SELECT
button.
Move a pointer to source that you want to select and then press
SELECT button.
Input 1
RGB(Analog)
Source Select Menu
Move a pointer to source
and press SELECT button.
When your computer is connected to INPUT 1 (ANALOG)
terminal, select RGB(Analog).
RGB(Scart)
When video equipment is connected to INPUT 1 (ANALOG)
terminal, select RGB(Scart).
RGB(PC Digital)
NOTE;
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB(PC Digital).
HDCP (High-bandwidth Digital Content
Protection) is a system for protecting digital
entertainment content which is delivered by DVI
(Digital Visual Interface) from being copied.
The specification of HDCP is decided and
controlled by Digital Content Protection, LLC.
Should the specification be changed, this
projector may not display the digital content
protected by HDCP.
RGB(AV HDCP)
If a HDCP-compatible signal source is connected to the INPUT 1
(DIGITAL) terminal, select RGB(AV HDCP).
Monitor out
If the INPUT 1 ANALOG terminal is being used as a MONITOR
OUT terminal, select Monitor out.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connect a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.
INPUT MENU
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
1
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Press POINT UP/DOWN button to move a red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
2
Input 2
Press POINT UP/DOWN button and a red-arrow icon will
appear. Move arrow to "RGB", and then press SELECT button.
3
Source Select Menu
Move a pointer to RGB and
press SELECT button.
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 49). When a computer is selected, this projector automatically
tunes to incoming signal and projects the proper image without any special setting. (Some computers need to be set
manually.)
The projector displays one of the Auto, -----, Mode 1/2/3/4/5, or the system provided in the projector.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
PC SYSTEM MENU
Auto
When image is not provided properly, manual adjustment
is required. (Refer to P26 and 27.)
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.
(Refer to TROUBLESHOOTING on page 46.)
––––
User preset adjustment in MANUAL PC ADJUSTMENT.
Adjustment data can be stored in the Mode 1-5.
Mode 1
SVGA 1
Computer systems provided in the projector. The
projector chooses proper system and displays it.
✽
Mode 1 and SVGA 1 are examples.
PC SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
PC SYSTEM Menu icon
Displays system being selected.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
1
Systems on this dialog box can
be selected.
Custom Mode (1~5) set in PC
ADJUST Menu. (P26, 27)
Press POINT UP/DOWN button to move a red arrow pointer to
2
system that you want to set, and then press
SELECT button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
PC ADJUST Menu icon
Press POINT UP/DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Top Control or on Remote Control
Unit.
Move a red frame pointer to AUTO
PC Adj. icon and press SELECT
button.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P24). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P27).
NOTE
G Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 26,
27.)
G Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “480p”, “575p”, “480i”, “575i”
“720p (HDTV)”, “1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal is selected on PC SYSTEM
MENU (P24).
PC ADJUST MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
1
PC ADJUST Menu icon
Press POINT UP/DOWN button to move a red frame pointer to
2
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust value.
Move a red frame icon to item and
press SELECT button.
Fine sync
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value. (From 0 to 31.)
Total dots
Shows status
(Stored / Free) of
selected Mode.
Adjust the number of total dots in one horizontal period. Press
POINT LEFT/RIGHT button(s) and adjust number to match your PC
image.
Selected Mode
Horizontal
Adjusts horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Press POINT LEFT/RIGHT
button to adjust value.
Vertical
Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)”
or set “Full screen.”
Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Current mode
Press SELECT button to show information of computer selected.
Clamp
Current mode
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
information of computer
connected.
Press SELECT button at this icon
to display previous items.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
Press SELECT button at
Display area icon and Display
area dialog box appears.
Display area
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Display area
Display area H
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.
Full screen
Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit
screen. This function cannot be adjusted when “ON” is selected on
Anamorphic function (P38).
To store adjustment data.
This Mode has parameters being stored.
NOTE : Fine sync, Display area, Display area H, Display area V and
Full screen cannot be adjusted when “480p”, “575p”, “480i”,
“575i”, “720p (HDTV)”, “1035i (HDTV)” or “1080i (HDTV)” is
selected on PC SYSTEM Menu (P24).
Store
3
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.
Mode free
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button. Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.
Store icon Vacant Mode Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
To clear adjustment data.
Other icons operates as follows.
Reset
Reset all adjust parameters on adjustment dialog box to previous
figure.
Quit
Closes PC ADJUST MENU.
Mode free icon
Close this dialog box.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on Top Control or on Remote
Control Unit.
IMAGE button
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Image 2
Image 3
Image 4
Real
Picture level with improved halftone for graphics.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P36).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT UP/DOWN button to move a red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Move a red frame icon to level and
press SELECT button.
Real
Picture level with improved halftone for graphics.
Level being selected.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P36).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
SCREEN Menu icon
Press POINT UP/DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
Move red frame to function and press
SELECT button.
Normal
Provides image to fit screen size.
True
Provides image in its original size. When original image size is larger
than screen size (1024 x 768), this projector enters “Digital zoom +”
mode automatically.
NOTE
G True and Digital zoom +/– cannot be operated
when “480i”, “575i”, “480p”, “575p”, “1035i (HDTV)”
or “1080i (HDTV)” is selected on PC SYSTEM
Menu (P24).
Wide
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16 : 9.
G Wide cannot be selected when “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on
PC SYSTEM Menu (P24).
G This projector cannot display any resolution higher
than 1280 X 1024. If your computer’s screen
resolution is higher than 1280 X 1024, reset
resolution to lower before connecting projector.
Digital zoom +
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM L
button on Remote Control Unit.
G Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.
G Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
Digital Zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM M
button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
L/M, SELECT, POINT and LASER buttons.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING INPUT SOURCE
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT Menu.
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
1
INPUT Menu icon
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Press POINT UP/DOWN button to move a red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
2
Input 2
Move a pointer to source that you want to select and then press
Source Select Menu
3
SELECT button.
Move a pointer to Video or
Y, Pb/Cb, Pr/Cr and press
SELECT button.
When video input signal is connected to VIDEO jack,
Video
select Video.
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
WHEN SELECT INPUT 3 (AV TERMINALS )
INPUT MENU
When connecting to those equipment, select a type of Video
source in SOURCE SELECT (VIDEO) Menu.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
INPUT Menu icon
1
Move a pointer (red arrow) to
Input 3 and press SELECT
button.
Press POINT UP/DOWN button to move a red arrow pointer to
Input 3 and then press SELECT button. Source Select Menu will
appear.
2
Input 3
Source Select Menu (VIDEO)
Move a pointer to source that you want to select and then press
SELECT button.
Move a pointer to source
and press SELECT button.
3
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
When video input signal is connected to S-VIDEO jack,
select S-Video.
S-Video
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.
1
2
Press POINT UP/DOWN button to move a red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move pointer to system
and press SELECT button.
Y, Pb/Cb, Pr/Cr JACKS
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i or 1080i, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
COMPONENT VIDEO SIGNAL FORMAT
Move pointer to system and
press SELECT button.
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Top Control or on
Remote Control Unit.
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P36).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT UP/DOWN button to move a red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Move red frame pointer to level
and press SELECT button.
Normal picture level preset on this projector.
Level being selected.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P36).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT UP/DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move red frame to function and press
SELECT button.
Normal
Provides image at a normal video aspect ratio of 4 : 3.
NOTE : SCREEN Menu cannot be operated when
“720p,” “1035i,” or “1080i” is selected on AV
SYSTEM Menu (P31).
Wide
Provides image at a wide screen ratio of 16 : 9.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
PICTURE IMAGE ADJUSTMENTS
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press POINT UP/DOWN button to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Level of each item is displayed. Adjust each level by pressing
POINT LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move a red frame pointer to
item to be selected and then
press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)
Tint
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Color Management
The Color management function can be used to adjust the level,
phase and gamma of the selected display colors on the screen, and
to replace these colors with other colors if required.
The projector lets you replace up to eight colors for each image.
There are four preset images for VIDEO mode and four preset
images for PC, giving a total of eight images.
Press the POINT UP/DOWN button to move the red frame point-
er to "COLOR MANAGEMENT", and then press the SELECT
button. The COLOR MANAGEMENT menu will appear and
pointer mode will be enabled. The image that was being project-
ed when the button was pressed will be paused, and the COLOR
MANAGEMENT POINTER will appear.
1
POINTER MODE
COLOR
MANAGEMENT
POINTER
Use the POINT buttons to move the pointer to a section of the
paused image that contains the color that you would like to
adjust, and then press the SELECT button. The mode will
change to COLOR SELECTION mode, and the color in the cen-
ter of the pointer will be selected and adjustment will be possi-
ble.
2
NOTE;
Press the COLOR M. button on the remote con-
trol to display the COLOR MANAGEMENT menu.
If you would like to check or re-adjust a color
management setting that has already been made,
press the COLOR M. button on the remote control
once more to change to LIST mode.
Use the POINT buttons to adjust the level and phase of the
color, and then press the SELECT button to confirm the setting.
Next, use the POINT buttons to adjust the gamma correction for
the color, and then press the SELECT button to accept the set-
ting. When the SELECT button is pressed, the mode will change
to LIST mode.
3
34
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
To move the red frame pointer to "MENU", and then press the
SELECT button. The message "OK"? is displayed. Move the
COLOR SELECTION
MODE
4
pointer to
The COLOR
[Yes] and then press SELECT button.
Level and phase
adjustment palette.
Gamma
adjustment palette.
MANAGEMENT menu will be exited and the display will return
to the IMAGE ADJUST menu. (At this time, the image will stop
being paused and normal projection will resume.) After chang-
ing the COLOR MANAGEMENT settings, use the IMAGE
ADJUST menu to store the changed settings.
COLOR SELECTION MODE
CANCEL
The mode will return to the pointer mode (even if you press the
MENU key on the projector or the remote control). (You will need to
reselect and re-adjust the color in this case.)
QUIT
LIST
CANCEL
QUIT
The COLOR MANAGEMENT menu will be exited and the display will
return to the normal projection screen, but any settings that have
been changed will not be stored. To store the changed settings, be
sure to select "LIST" using the POINT buttons and change to the
next mode (LIST mode).
LIST MODE
COLOR PALETTE
DEL
LIST MODE
The check mark will be cleared and the effect of the setting adjustment
for that line on the projected images will be momentarily canceled.
COLOR PALETTE
The mode will return to COLOR SELECTION mode so that you can
re-adjust the setting for the color in that line. This option is not avail-
able if the check mark has been cleared by the operation immediate-
ly above.)
ALL DEL
MENU
COLOR M.
DEL
NOTE;
The setting adjustment for the color in that line will be canceled.
If you press the COLOR M. button on the remote
control, the COLOR MANAGEMENT menu will be
exited and the display will return to the normal
projection screen, but any settings that have been
changed will not be stored. To store the changed
settings, be sure to select "MENU" using the
POINT buttons and store the settings.
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
COLOR M.
The mode will return to POINTER mode.
Auto picture control
Press either POINT LEFT button or POINT RIGHT button to Auto
picture control position that you want to select . (Off, L1 or L2)
Off ······· Auto picture control OFF position.
L1 ········ Auto picture control LEVEL 1 position.
L2 ········ Auto picture control LEVEL 2 position.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press SELECT button at this icon
to display other items.
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press SELECT button at this icon
to display previous items.
Press POINT LEFT button to soften the image, and POINT RIGHT
button to sharpen the image. (From 0 to 31.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Noise reduction
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
Progressive scan
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off”, “L1”, “L2”.
Off ··· Progressive scan mode to OFF.
L1 ···· Progressive scan mode to ON (for active picture).
L2 ···· Progressive scan mode to ON (for still picture).
Store
To store manually preset image, move a red frame pointer to Store
icon and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image 1 to 4 where you want to set and
then press SELECT button.
Image Level Menu
Move a red frame pointer to
any of Image 1 to 4 where you
want to set and then press
SELECT button.
Other icons operates as follows.
Store icon
Reset
Press SELECT button at this
icon to store the adjustment.
Reset all adjustment to previous figure.
Quit
NOTE :
Tint cannot be adjusted when the video system is
PAL, SECAM, PAL-M or PAL-N.
Closes IMAGE MENU.
Progressive cannot be operated when “480p”, “575p”
or “720p” is selected on AV SYSTEM MENU (P31).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.
SETTING MENU
1
2
Press POINT DOWN button to move a red-frame pointer to item
SETTING Menu icon
that you want to set and then press
dialog box appears.
SELECT button. Setting
Set a red frame
pointer to item and
press SELECT
button.
Language
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
Lamp mode
When selecting the Lamp mode, the projector reduce the brightness
and set into the low power consumption mode.
When pressing SELECT
button at Language,
Language Menu appears.
Normal mode
Auto mode
The brightness is adjusted automatically to a
level that is suitable for the screen.
The brightness is reduced to 80% of Normal
mode.
Eco mode
Keystone
When the image is distorted, select Keystone. ON-SCREEN MENU
disappears and Keystone dialog box is displayed.
Store ··· Store the keystone adjustment data when disconnect AC
Power Cord from an AC outlet.
Reset ··· Reset the keystone adjustment data when disconnect AC
Power Cord from an AC outlet.
When a SELECT button is pressed, the mode changes to keystone
adjustment mode. Correct keystone distortion by pressing POINT
UP/DOWN/LEFT/RIGHT button(s). Refer to KEYSTONE
ADJUSTMENT on page 21.
Move a pointer to item and
then press POINT
LEFT/RIGHT button(s).
Aspect V
Aspect H
These adjust the vertical and horizontal scale and position of the
screen. Use the POINT RIGHT/LEFT button(s) to select Store or
Reset.
Store ··· Store the adjustment data when disconnect AC Power
Cord from an AC outlet.
Reset ··· Reset the adjustment data when disconnect AC Power Cord
from an AC outlet.
When a SELECT button is pressed, the mode changes to Scale or
Position adjustment mode. Use the POINT LEFT/RIGHT button(s) to
select whether you wish to adjust Scale or Position, and then use the
POINT UP/DOWN button(s) to adjust the values.
NOTE :
When the Aspect H/V is adjusted and the keystone adjustment is
made, the adjustment data for the Aspect H/V is cleared.
To maintain the adjustment data, perform keystone adjustment first,
and then adjust the Aspect H/V.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Anamorphic
When this function is “On,” the screen image is forcibly changed to a
4:3 image, even if the input signal is HDTV.
Blue back
When this function is “On,” this projector will produce a blue image
instead of the video noise on the screen when any input source is
unplugged or turned off.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all the On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
G ON-SCREEN MENU
G “Power off?” message
G P-TIMER
G “No signal” message
G “Wait a moment” message
Menu position
This function is used to adjust the on-screen menu display position.
When a SELECT button is pressed, the adjustment screen is
displayed (arrows appear). Use the POINT UP/DOWN/LEFT/RIGHT
button(s) to adjust the position. After making the adjustment, press a
SELECT button to return to the Menu screen.
Logo
When this function is “On,” projector displays logo when starting up.
Ceiling
Press SELECT button at this icon
to display other items.
When this function is “On,” picture is top / bottom and left / right
reversed. This function is used to project the image from a ceiling
mounting the projector.
Ceiling function
Press SELECT button at this icon
to display previous items.
Rear
When this function is “On,” picture is left / right reversed. This
function is used to project the image to a rear projection screen.
Rear function
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Power management
This projector is equipped with a power management function. When the input signal is interrupted and any button is not
pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and
conserve lamp operating time. The factory default settings for power management are "Ready" and "5 Min".
OPERATION
1) If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message "No signal" and the
timer display appears on the screen. Then the count-down starts for the time being set.
If "Ready" is selected
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
3) When the lamp cooling is completed, the READY indicator
starts flashing to notify the operator that power
management mode is active. In this condition, the lamp
When a SELECT button is pressed,
the adjustment screen is displayed.
will turn on and images will be projected if a signal starts
being input or the projector is operated.
If "Shut down" is selected
Use the POINT LEFT/RIGHT button(s)
to select the power management
function mode ("Off", "Ready" or "Shut
down").
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
3) When the lamp cooling is completed, the power switches
off.
Use the POINT DOWN button to move
the pointer to the time setting, and then
use the POINT LEFT/RIGHT button(s)
to set the time (1 minute to 30
minutes).
If "Off" is selected
The power management function is canceled.
Time left until Lamp off.
On start
When this function is “On,” projector is automatically turned on just
by connecting AC Power cord to a wall outlet.
Note ; Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P20). If projector is turned
off in wrong steps, On Start function does not operate
properly.
Remote control
This projector has eight different remote control codes; the factory-
set normal code (Code 1) and the other seven codes (Code 2 to
Code 8). This switching function prevents remote control operation
mixture (jam) when operating several projectors or video equipment
together.
For example operating projector in “Code 7,” both projector and
Remote Control Unit must be switched to “Code 7.”
To change the code of Projector;
To change the Remote control code of the projector used in ON-
SCREEN MENU is selectable from Code 1 to Code 8.
To change the code of the Remote Control Unit;
To change the remote control code of the Remote Control Unit, set
the DIP switches 1-3 inside the battery compartment box of the
Remote Control Unit. (Refer to P15.)
When pressing SELECT button at
Remote control, Remote control
code Menu appears.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
USB
This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.
Wireless Mouse mode
Select "
" when controlling a computer with Remote Control of
this projector.
Projector mode
Select "
" when controlling a projector with computer.
NOTE: This is provided not for basic operation but for future use.
Key lock
This function locks the operation of the projector's control panel and
the remote control.
This locks operation of the projector's control panel.
This locks operation of the remote control.
This cancels the Key lock function.
If the projector's control panel accidentally becomes locked and you
do not have the remote control nearby, disconnect the AC cord to
turn off the power, and then while pressing a SELECT button,
reinsert the AC cord, This will cancel the projector's control panel
lock.
Lamp counter reset
This function is used to reset Lamp Replace Counter. When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function. Refer to page 45 for operation.
Factory default
This function returns all setting values except for the lamp counter to
the factory default settings.
Press POINT UP/DOWN button to move a red frame pointer to
“Factory default” and then press
SELECT button. The message
"Return to Factory default?" is displayed. Move the pointer to [Yes]
and then press SELECT button.
Another confirmation dialog box appears and select [Yes]
and then
Return the projector to Factory default.
press SELECT button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPERATING WIRELESS MOUSE
Wireless Remote Control Unit is not only able to operate this projector but also function as a wireless mouse for most
Personal Computers. POINT button, drag ON/OFF button and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.
INSTALLATION
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of the mouse driver (not
supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse
port (or USB port) of a Personal Computer is activated.
Connect the mouse port (or USB port) of your computer to
Control Port (or USB connector) of this projector with Control
Cable (or USB cable). (Refer to page 12, 13 for connection.)
Note : When your computer has no mouse
1
port, connect Serial Port of your
computer to Control Port of the
projector with Control Cable for Serial
Port (supplied).
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, Wireless Mouse may not
work properly.
2
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, Drag ON/OFF button, LEFT CLICK
button and RIGHT CLICK button on Wireless Remote Control Unit.
POINT button
Used to move PC mouse pointer. The pointer is moved
DRAG ON
corresponding with the direction you are pressing.
INDICATOR
LEFT CLICK button
This button has the same function as the left button in a PC mouse.
Press this button and the POINT button to drag a selected screen
object.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
DRAG ON/OFF button
DRAG ON/OFF
button
Use this button and the POINT button to drag a selected screen
object. Press and release the Drag ON/OFF button, DRAG ON
INDICATOR lights green and the remote control is in Drag mode.
Use the POINT button in the direction that you want to drag the
screen object. Press and release the Drag ON/OFF button again or
press any other button, to drop the object at the new screen location.
POINT button
(Move the pointer)
LEFT CLICK button
RIGHT CLICK button
(left button of the mouse)
(right button of the mouse)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
The Warning Temp. Indicator flashes red to let you know the internal temperature
of the projector exceeds the normal level. If the temperature goes up further, the
projector will be turned off automatically and the Ready indicator will go out. (The
Warning Temp. Indicator continues flashing.) After the cooling-off period, the
Ready Indicator lights on again and the projector can be turned on by pressing the
On/Off button on the remote control unit or on the top control. When you turn on
the projector, the Warning Temp. Indicator will go out.
TOP CONTROL
Ready
Warning Temp.
Indicator
Indicator
If the Warning Temp. Indicator is still flashing, check the followings;
Ventilation Slots of a projector may be blocked. In such an event, reposition
a projector so that Ventilation Slots are not obstructed.
1
Air Filter may be clogged with dust particles. Clean Air Filter by following
section AIR FILTER CARE AND CLEANING on next page.
2
If WARNING TEMP. Indicator remains on after performing above checks,
Cooling Fans or Internal Circuits may be malfunctioning. Contact the service
station.
3
When both of the Warning Temp. and Ready indicators are flashing:
When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready
Indicators starts flashing. In this condition, the projector cannot be turned on even if you press the On/Off button on the
remote control unit or on the top control. If this case happenes, disconnect and reconnect the AC power cord, and then turn
on the projector again to check its operation. If the projector shuts down again or fails to be turned on, the internal check and
repair will be required. Plug off the AC power cord and contact service station.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
AIR FILTER CARE AND CLEANING
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become
clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely
affect life of a projector. Clean Air Filter following steps below:
Turn off a projector, and disconnect AC power cord from AC
outlet.
1
Turn a projector upside down and remove Air Filter (2 used) by
pulling latches upward.
2
Clean Air Filter with a brush or wash out dust and particles.
3
4
Replace Air Filter properly. Make sure that Air Filter is fully
inserted.
CAUTION
Do not operate a projector with Air Filter removed. Dust
may accumulate on LCD Panel and Projection Mirror
degrading picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of a projector.
AIR FILTER
Pull up and remove.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments
may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements
inside a projector. This condition may degrade quality of a projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean Projection Lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
1
Lightly wipe a cleaning cloth over Projection Lens.
2
3
When a projector is not in use, replace Lens Cover.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
LAMP REPLACE
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow. If this indicator lights
yellow, replace the projection lamp with a new one promptly.
TOP CONTROL
This indicator lights yellow
when the life of the projection
lamp draws to an end.
Replace the Projection Lamp
with a new one promptly.
CAUTION
Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover. The inside of a projector can
become very hot.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
Turn off a projector and disconnect AC plug. Allow a projector to
cool for at least 45 minutes.
1
Loosen 2 screws with a screwdriver and open Lamp Cover.
2
3
Loosen 2 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.
LAMP COVER
HANDLE
Replace Lamp Assembly with a new one and tighten 2 screws
back. Make sure that Lamp Assembly is set properly. Replace
Lamp Cover and tighten 2 screws.
4
LAMP
ASSEMBLY
Connect AC Power Cord to a projector and turn it on.
5
6
Reset Lamp Replace Counter (refer to next page “Lamp Replace
Counter” section).
NOTE : Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the
following information to the dealer.
G Model No. of your projector
:
:
PLC-XP55/XP55L/XP56/XP56L
G Replacement Lamp Type No.
POA-LMP67 (for PLC-XP55/XP55L)
(Service Parts No. 610 306 5977)
G Replacement Lamp Type No.
:
POA-LMP81 (for PLC-XP56/XP56L)
(Service Parts No. 610 314 9127)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACE COUNTER
Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset,
the LAMP REPLACE Indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon (refer to
page 40).
1
Press POINT UP/DOWN button to move a red frame pointer
2
to “Lamp counter reset” and then press
SELECT button. The
message "Lamp replace counter reset?" is displayed. Move
the pointer to [Yes] and then press SELECT button.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
3
Move the pointer to Lamp counter reset and then press
SELECT button. The message “Lamp replace counter
reset?” is displayed.
NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
G Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
G If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
G A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 12 ~ 14.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.
Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to
turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and
computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
G Plug a projector into your AC outlet.
G Make sure READY Indicator lights.
G Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
G Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector cannot be turned on.
(See "TURNING ON/OFF PROJECTOR" section on page 20.)
G Check Projection Lamp. (Refer to page 44.)
G Adjust focus of a projector.
G Make sure a projection screen is at least 4.6’ (1.4m) from a projector.
G Check Projection Lens to see if it needs cleaning.
Image is out of
focus.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.
G Check Ceiling/Rear feature. (See “SETTING” section on page 38.)
Picture is Left/Right
reversed.
G Check Ceiling feature. (See “SETTING” section on page 38.)
Picture is
Top/Bottom
reversed.
G Check Display feature.(See “SETTING” section on page 38.)
Some displays are
not seen during
Operation.
G Check connection between your computer or video equipment and a projector.
G When turning a projector on, it takes about 30 seconds to display an image.
G Check system that you select is corresponding with your computer or video equipment.
G Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No image.
G Check audio cable connection from audio input source.
G Adjust audio source.
No sound.
G Press VOLUME (+) button.
G Press MUTE button.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solutions
G Check batteries.
G Check ALL-OFF switch on Remote Control Unit is set to “ON”.
G Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
G Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
G Check transmitted signal mode from Remote Control Unit.
(See“SETTING” section on page 39.)
G Check cable connection between a projector and your computer.
G Check mouse setting on your computer.
G Turn a projector on before turning on a computer.
Wireless Mouse
function does not
work.
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT-
ING" section on pages 46, 47. To correct failure, try "Solutions".
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.
Indicators
Projector Condition
WARNING
READY
TEMP.
green
LAMP
REPLACE
yellow
LAMP
red
red
The projector is OFF. (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF button.
✽
✽
The projector is operating normally.
The Warning Temp. Indicator flashes red to let you know the
internal temperature of the projector exceeds the normal level. If
the temperature goes up further, the projector will be turned off
automatically and the Ready indicator will go out. When the pro-
jector is cooled down enough and the temperature returns to nor-
mal, the READY indicator lights green and the projector can be
turned on. (The WARNING TEMP. indicator keeps flashing.)
Check and clean the Air Filter.
✽
The projector is cooled down enough and the temperature
returns to normal. When turning on the projector, the WARNING
TEMP. indicator stops flashing. Check and clean the Air Filter.
✽
✽
The projector is being cooled down. It cannot be turned on until
the READY indicator lights green.
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC Power Cord and plug it again to turn
on the projector. If the projector is turned off again, disconnect
the AC Power Cord and contact the dealer or the service center
for service and checkup. Do not leave the projector on. It may
cause electric shock or a fire hazard.
✽
The projector is in the Power management mode.
✽
• • • on
• • • flashing
• • • dim
• • • off
✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow,
replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 180 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480p
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
31.47
31.25
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
59.88
50.00
60.00
50.00
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
1024 x 768
1024 x 768
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
63.90
75.00
80.00
45.00
33.75
33.75
28.125
77.07
75.70
86.96
58.20
58.30
72.00
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
86.00
94.00
60.01
72.00
66.00
86.70
60.18
60.00
75.08
75.08
60.00
60.00
60.00
50.00
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
SXGA 19 1280 x 1024
SXGA 21 1400 x 1050
MAC
––––––––
(Progressive)
––––––––
(Progressive)
––––––––
(Interlace)
––––––––
(Interlace)
575p
480i
575i
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1152 x 900
1280 x 1024
(Interlace)
1280 x 960
1280 x 1024
MAC
––––––––
720p (HDTV)
1035i (HDTV)
1080i (HDTV)
1080i (HDTV)
(Progressive)
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Interlace)
1024 x 768
(Interlace)
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
D-VGA
D-480p
D-575p
D-SVGA
D-XGA
640 x 480
31.47
31.47
31.25
37.879
43.363
63.98
59.94
59.88
50.00
60.32
60.00
60.02
D-SXGA2 1280 x 1024
60.276
45.00
33.75
33.75
28.125
58.069
60.00
60.00
60.00
50.00
720 x 480
1280 x 720
D-720p
D-1035i
(Progressive)
(Progressive)
768 x 575
(Progressive)
1920 x 1035
(Interlace)
1920 x 1080
(Interlace)
800 x 600
D-1080i
1920 x 1080
1024 x 768
D-1080i
(Interlace)
D-SXGA1 1280 x 1024
NOTE : Specifications are subject to change without notice.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MENU TREE
Input
Input
SYSTEM
1)
Input 1
RGB
RGB( Scart)
RGB(PC Digital)
RGB( AV HDCP )
SYSTEM
1)
SYSTEM
2)
Monitor out
Video
SYSTEM
3)
Input 2
Y, Pb/Cb, Pr/Cr
RGB
SYSTEM
4)
SYSTEM
1)
SYSTEM
3)
Input 3
Video
Y, Pb/Cb, Pr/Cr
S-Video
SYSTEM
4)
SYSTEM
3)
PC source
Video source
Screen
Normal
True
System
2)
Wide
D-480p
System
1)
Mode 1
Mode 2
VGA 1
Digital zoom +
Digital zoom -
System
3)
Auto
PAL
SVGA 1
XGA 1
PC adjust
Auto PC Adj.
Fine sync
Total dots
Horizontal
Vertical
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
0 - 31
Image
Standard
Current mode
Clamp
Real
System
4)
Auto
1080i
1035i
720p
575p
480p
575i
Image 1
Image 2
Image 3
Image 4
Display area
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 1024
1400 x 1050
1600 x 1200
Quit
480i
Display area H
Display area V
Full screen
Reset
Image
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
On/Off
Yes/No
Mode free
Store
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Normal
Wide
Screen
Quit
50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
System
Setting
Language
English
Image adjust
Contrast
0 - 63
German
French
Brightness
Color
0 - 63
0 - 63
Italian
Tint
0 - 63
Spanish
Portuguese
Dutch
Color management
Auto picture control
0 - 63
Off/L1/L2
XLow/Low/Mid/High
Color temp.
Red
Swedish
Russian
Chinese
Korean
0 - 63
Green
0 - 63
Blue
0 - 63
Sharpness
Gamma
Noise reduction
Progressive
Reset
0 - 31
Japanese
Quit
0 - 15
On/Off
Off/L1/L2
Yes/No
Image 1
Image 2
Image 3
Image 4
Quit
Lamp mode
Keystone
Aspect V
Normal/Auto/Eco
Store/Reset
Store/Reset
Scale
Store
Position
Scale
Aspect H
Store/Reset
Position
Anamorphic
Blue back
On/Off
On/Off
On/Off
Quit
Display
Menu position
Logo
On/Off
Ceiling
On/Off
Rear
On/Off
Power management
On start
Off/Ready/Shut down
On/Off
Remote control code
Code 1
Code 2
Code 3
Code 4
Code 5
Code 6
Code 7
Code 8
Quit
USB
Mouse
Projector
Off
Key lock
Control panel
Remote control
Yes/No
Lamp counter reset
Factory default
Yes/No
Sound
Volume
0 - 63
Built-in SP.
Mute
On/Off
On/Off
Quit
51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
12.6" x 6.6" x 18.5" (319 mm x 168 mm x 470 mm)
20.3 lbs (9.2 kg) PLC-XP55/XP56, 17.4 lbs (7.9 kg) PLC-XP55L/XP56L
1.3" TFT Active Matrix type, 3 panels
1024 x 768 dots
(W x H x D)
Dimensions
Net Weight
LCD Panel System
Panel Resolution
2,359,296 (1024 x 768 x 3 panels)
Number of Pixels
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Color System
480i, 480p, 575i, 575p, 720p, 1035i and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
F1.7 ~ 2.0 lens with f=48.2 mm ~ 62.6 mm Motor zoom and focus
4.6' (1.4 m) ~ 48.3' (14.7 m)
High Definition TV Signal
Scanning Frequency
Projection Lens
Throw distance
Up and Down
Motorized Lens Shift
Projection Image Size (Diagonal)
Horizontal Resolution
Projection Lamp
Adjustable from 31" to 400"
800 TV lines (HDTV)
300 watt type
DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)
Input 1/Monitor Output Jacks
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V),
Stereo Mini Type Jack (Audio)
Input 2 Jacks
Input 3 Jacks
Other Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack
and PJ-Net Organizer Connector
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
Built-in Speakers
Feet Adjustment
0˚ to 10.5˚
Voltage and
Power Consumption
AC 100 ~ 120 V (5.0 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (2.5 A Max. Ampere), 50 / 60 Hz (Continental Europe and The U.K.)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Operating Temperature
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / 30˚
2.0” x 1.4” x 7.6” (50mm x 36mm x 193mm)
0.35 lbs (160 g) (including batteries)
(Max. Output : 1mW / Wave length : 650 20nm)
Class II Laser
Remote Control Transmitter
Owner’s Manual
AC Power Cord
Accessories
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable
USB Cable
Control Cable for Serial port
Protective Dust Cover
Lens Cover (PLC-XP55/XP56)
Lens Attachment (PLC-XP55L/XP56L)
G Specifications are subject to change without notice.
G LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 and MONITOR OUT TERMINALS (ANALOG)
Terminal : HDB15-PIN
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
+5V Power
Pin Configuration
10 Ground (Vert.sync.)
11 Sense 0
12 DDC Data
2
1
5
4
3
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 DDC Clock
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
Pin Configuration
T.M.D.S. Data2+
10 T.M.D.S. Data1+
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
1
9
2
3
4
5
6
7
8
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)
16 Hot Plug Detect
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
No Connect
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
PS/2
-----
Serial
R X D
-----
ADB
-----
Pin Configuration
1
2
3
4
5
6
7
8
CLK
DATA
GND
-----
ADB
-----
-----
8
7
6
GND
GND
-----
5
4
3
RTS / CTS
T X D
GND
2
1
-----
-----
GND
-----
-----
GND
GND
USB CONNECTOR (Series B)
Pin Configuration
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.
G Control Cable (PS2 Port)
G Control Cable (ADB Port)
G MAC Adapter
Type No. : POA-MCPS2
Type No. : POA-MCMAC
Type No. : POA-MACAP
Type No. : KA-DV20
G DVI Cable
G HDB 15 pin-SCART 21 pin Cable Type No. : POA-CA-SCART
G Long Zoom Lens
G Ultra Long Zoom Lens
G Short Zoom Lens
G Short Fixed Lens
G PJ-Net Organizer
Type No. : LNS-T31A
Type No. : LNS-T32
Type No. : LNS-W31A
Type No. : LNS-W32
Type No. : POA-PN02
LENS REPLACEMENT
The lens of this projector can be replaced with other optional lens which are sold separately. This feature enables you to use
the projector for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be installed or replaced
by well-trained sales or service engineers. Do not attempt to do by yourself as it may cause injury.
To the sales and service engineer;
Referring to the attached lens replacement and installation manual, replace or install the lens properly.
After installing the lens, attach the lens cap to the lens when setting up the projector.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
Part No. 610 315 6798 (1AA6P1P3948A- ME5A)
SANYO Electric Co., Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
|