Assembly Instructions for Model: WFV66
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is
constructed of real hardwood and resonance dampening MDF.
Safety Warning: If you do not understand these directions, or have any doubts about the
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or
customer service representatives can quickly assist you with installation questions and missing
or damaged parts. Replacement parts for products purchased through authorized dealers will be
shipped directly to you. Never use defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus
Systems. Sanus Systems can not be liable for damage or injury caused by incorrect assembly, or
incorrect use. Please call Sanus Systems before returning products to the point of purchase.
Required Tools: Phillips screw driver
Supplied Parts and Hardware: Some parts may be pre-assembled together*
Hardware: Shown as actual size
(24) Cam Pin - a
(8) Dowel Pin - c
(24) Dowel - d
(24) Shelf Pin - e
(24) Cam - b
(12) Wood Screw - f
(8) Spacer - g
(6) Phillips Bolt - h
(3) Door Handle - i*
(12) Hinge Screw - j
(12) Hinge Plate Screw - k
Parts: Not Shown as actual size
(6) Hinge - l*
(6) Hinge Plate - m*
(6) Back Stretcher - p
(6) Front Stretcher - o
(1) Top - n
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Prepare Center Panels
Thread a Cam Pin (a) into each of the smaller holes in each Center Panel (x). Tighten each Cam Pin with a Phillips screw driver. Insert
a Dowel (d) into the larger adjacent hole in the Panels. See Diagram 2 for assistance.
Diagram 2
Detailed View
x
a
d
Step 3: Prepare Stretchers
Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the
Stretchers. See Diagram 3 for assistance.
Diagram 3
Detailed View
o
b
arrow
p
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Add Stretchers
Add the Front and Back Stretchers (o,p) to the Side Panel (v), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and
the Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to
the Side Panel in a clockwise motion until the stretchers are secured. See Diagram 4 for assistance. Note: Front stretchers attach
to the same side as the hinge holes are on.
Diagram 4
Detailed View
v
d
p
hinge
holes
a
b
Step 5: Add First Center Panel
Press fit the Center Panel (x) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel
() fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Center Panel. See Diagram
5 for assistance. Note: Make sure the hinge holes on the Center Panel are on the same side as the Front Stretchers.
Diagram 5
Detailed View
o
x
hinge
holes
a
d
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6: Add Stretchers
Add the Front and Back Stretchers (o,p) to the Center Panel (x), by aligning the Cam Pin (a) with the hole which the Cams (b) point to.
The Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to
the Center Panel in a clockwise motion until the stretchers are secured. See Diagram 6 for assistance. Note: Front stretchers attach
to the same side as the hinge holes are on.
Diagram 6
Detailed View
x
a
b
d
p
Step 7: Add Second Center Panel
Press fit the Center Panel (x) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel
(d) fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Center Panel. See Diagram
7 for assistance. Note: Make sure the hinge holes on the Center Panel are on the same side as the Front Stretchers.
Diagram 7
Detailed View
o
x
a
d
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 8: Add Stretchers
Add the Front and Back Stretchers (o,p) to the Center Panel (x), by aligning the Cam Pin (a) with the hole which the Cams (b) point to.
The Dowel (d) fits into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to
the Side Panel in a clockwise motion until the stretchers are secured. See Diagram 8 for assistance. Note: Front stretchers attach
to the same side as the hinge holes are on.
Diagram 8
Detailed View
x
a
hinge
holes
d
o
Step 9: Add Side Panel
Press fit the Side Panel (w) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel (d)
fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Side Panel. See Diagram 9 for
assistance. Note: Make sure the hinge holes on the Side Panel are on the same side as the Front Stretchers.
Diagram 9
Detailed View
o
a
w
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 10: Add Shelf Pins and Bottom Shelf
Thread the Shelf Pins (e) into the bottom hole in the line of holes in each Panel (v,w,x). Tighten Shelf Pins with a Phillips screw driver.
Add the Bottom Shelf (q) by inserting it into the assembly and press fit it onto the Shelf Pins. Make sure the Bottom Shelf is flush against
the Front Stretcher (o). If there is a gap in front the Bottom Shelf may be backward. See Diagram 10 for assistance.
Diagram 10
Detailed View
x
v
x
e
q
w
Step 11: Add Top
Gently tap a Dowel Pin (c) into the holes on the top of each Panel (v,w,x). Slide a Spacer (g) over each Dowel Pin. Press fit the Top (n)
so it fits onto the Dowel Pins. See Diagram 11 for assistance.
Diagram 11
Detailed View
n
c
g
w
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 12: Prepare Doors
Insert each Phillips Bolt (h) through the Door (s) and into the Door Handle (i). Tighten with a Phillips screw driver. See Diagram 12a
for assistance. The Door Panels can be interchanged by removing and re-installing the plastic border from the perimeter of the Door’s
back side.
Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (s). Tighten each with a Phillips screw driver. Repeat process
until each Hinge Assembly is secure. See Diagram 12b for assistance.
Diagram 12a
Diagram 12b
Detailed View
Detailed View
h
i
s
s
j
l
Step 13: Door Install
Position the Door (s) so the holes in the Hinge Plate (m) line up with the front pair of holes in the Panels (v,w,x). Insert a Hinge Plate
Screw (k) through the Hinge Plate and thread it into each hole in the Side Panel. Tighten with a Phillips screw driver. Repeat process so
each Hinge Assembly is secured. See Diagram 13 for assistance.
Detailed View
Diagram 13
s
v
m
k
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 14: Add Mid Shelves
Thread a Shelf Pin (e) into the desired location in the Panels (v,w,x). For each shelf, four Shelf Pins will be required. Insert each Mid
Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia-
gram 14 for assistance. Note: Diagram 14 is a Back View.
Detailed View
Diagram 14
v
x
x
e
r
w
Step 15: Add Back Panel
Position each Back Panel (u) up against the assembly and thread a Wood Screw (f) through it and into the Back Stretcher (p). Repeat
process until each Back Panel is secured with four Wood Screws. Tighten each with a Phillips screw driver. See Diagram 15 for assis-
tance.
Detailed View
Diagram 15
p
f
u
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 16: Hinge Adjustment for Woodbrook Door
Each hinge Assembly is adjustable in multiple directions. See Diagram 16 for assistance.
Diagram 16
Side Adjustment
Depth Adjustment
Height Adjustment
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05
Download from Www.Somanuals.com. All Manuals Search And Download.
|