Assembly Instructions for Model: JFBD1
ThankyouforchoosingtheJavaFurnitureLinefromSanusSystems.TheJFBD1
joins to Java Furniture Model JFV65 and serves as a backdrop for mounting
Sanus Wall Mount models VMPL50, VMPL250, VMPL, VMPL2, or VMPL3.
wARNINg
Do not use this product for any purpose that is not explicitly
specified by Sanus Systems. Improper installation may cause
property damage or personal injury. If you do not understand these
directions or have any doubts about the safety of the installation,
call a qualified contractor or contact Sanus at 800.359.5520 or
or injury caused by incorrect mounting, incorrect assembly, or
incorrect use.
CAUTIoN
The combined weight of your television and wall mount must not
exceed 130 lb (59 kg).
Supplied Parts and Hardware
Sanus Systems makes every effort to assure all necessary hardware is included. Check carefully to make sure that there
are no missing or defective parts. Never use defective parts. If hardware is missing or damaged, contact Sanus Systems or
consult your local hardware store. Contact Sanus Systems before returning products to the point of purchase. Replacement
parts for products purchased through authorized dealers will be shipped directly to you.
Threaded fasteners are shown actual size.
Required Tools: Phillips screwdriver, drill, and a 5/16″ diameter drill bit
NoTe
If you purchased the Java JFV65 Lowboy prior to buying the JFBD1, you may need the Sanus JFRU Update
Kit to properly assemble your furniture. Look for two sets of threaded inserts on both sides of the back of
the Lowboy as shown in Figure 2. If no inserts are present, contact Sanus Customer Service.
Backboard Joining Plate – C
Qty 4
Bottom Backboard – B
Qty 1
Top Backboard – A
Qty 1
¼-20 x 0.5″ Screw – E
¼″ Lock Washer – F
M8 x 40 mm Screw – D
Qty 4
Qty 24
Qty 24
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 09.27.06 (6901-100104)
Download from Www.Somanuals.com. All Manuals Search And Download.
NoTe
Do not fully tighten the ¼-20 x 0.5″ Screws (E) until assembly is complete.
Attach the Bottom Backboard (B) and Backboard Joining Plates (C) to your JFV65 and the Mounting Rails with eight
¼-20 x 0.5″ Screws (e) and eight ¼″ Lock Washers (F). See Figure 3.
Figure 3
Lock
washer (F)
Bottom
Backboard (B)
Screw (e)
Backboard Joining
Plate (C)
Lock
washer (F)
Screw (e)
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Attach Top Backboard to JFV65
CAUTIoN
The Top Backboard (A) is heavy. To avoid injury or product damage, two people must lift the Backboard.
Position the Top Backboard (A) on the Bottom Backboard (B). Make sure the dowels on the Top Backboard fit into the holes
on the Bottom Backboard. Push the Backboards together so there is no gap between them.
Use eight ¼-20 x 0.5″ Screws (e) and eight ¼″ Lock Washers (F) to fasten the Top Backboard to the Backboard Joining
Plates (C), and the Mounting Rails as shown in Figure 4. Make sure all twenty-four of the ¼-20 x 0.5″ Screws are tight.
Figure 4
Lock
washer (F)
Lock
washer (F)
Screw (e)
Screw (e)
Top
Backboard
(A)
Backboard
Joining Plate
(C)
Bottom
Backboard
(B)
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Attach wall Plate Provided with VMPL50, VMPL250, VMPL, VMPL2, or VMPL3
Decide where you would like the Wall Plate and mark the position of the two bottom holes through the slots in the Mounting
Rails. Use Table 1 below to correctly locate the position of the two upper slots in the Mounting Rails.
Table 1: Vertical(↕) Distance Between Wall Plate Slots
VMPL50
VMPL250
VMPL
VMPL2
VMPL3
4.5 in (114.3 mm)
4.5 in (114.3 mm)
6.5 in (165.1 mm)
6.5 in (165.1 mm)
6.0 in (152.4 mm)
NoTeS
Place a piece of tape over the areas where the drill bit will come through the Backboards (A and B). This
helps to prevent chipping of the wood surface. Remove the tape after the holes are drilled.
Use the M8 x 40 Screws (D). The Mounting Rail and Backboards (A and B) are too thick for the M8 x 16 mm
Screws provided with the Flat Panel TV Rails.
Drill through the selected slots with a 5/16″ drill bit. Drill from the back to the front of the Backboards (A and B).
Attach the Wall Plate to the Backboards (A and B) with four M8 x 40 mm Screws (D), M8 Lock Washers, and M8 Nuts, as
shown in Figure 5. The M8 Lock Washers and M8 Nuts are provided with the Flat Panel TV Rails. Make sure that all the
Screws are tight.
Figure 5
Mounting Rails
Top Backboard
(A)
Screw (D)
M8 Lock
washer
wall Plate
Bottom
Backboard (B)
M8 Nut
Step 5: Attach VMPL50, VMPL250, VMPL, VMPL2, or VMPL3 wall Mount
Attach the Wall Mount according to the assembly instructions provided with the unit.
CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, “CSAV”), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein
covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to
change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy,
completeness or sufficiency of the information contained in this document.
Download from Www.Somanuals.com. All Manuals Search And Download.
|