Assembly Instructions for Model: NFCD
Thank you for choosing a Sanus Systems Natural Media Tower. The Model
NFCD is designed to keep your collection clean and organized by storing up to
430 CDs or 230 DVDs, all in one convenient location.
If you do not understand these directions, please contact Sanus at 800.359.5520
defective parts. Our customer service representatives can quickly assist you
with assembly questions, and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper assembly may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
specified by Sanus Systems. Sanus Systems can not be liable for damage
or injury caused by incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: Rubber mallet or hammer, screwdrivers, phillips & regular
Supplied Parts List: (Not to Scale)
NFCD Top - A
Qty. 1
NFCD Base - B
Qty. 1
NFCD Foot - C
Qty. 4
Glass Shelves - F
Qty. 14
Side Panels - E
Center Support - D
Qty. 2
Qty. 1
Sanus Name Plate - G
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (100028)
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 - Insert Cam into Center Support.
Place a Cam (H) into each of the four holes in the Center Support (D)
NOTE: Each Cam has an arrow on it. Using a phillips screwdriver align each Cam so the arrow is pointing toward
the small hole on the edge of the Center Support (See Detail - A).
Diagram 3
Cam - H
Small
Hole
D
Cam Hole
Cam - H
Small Hole
Detail - A
Step 4 - Secure Side Panels to Center Support.
The Cam Pins (I) installed in each Side Panel (E) line up with the small holes in the edge of the Center Support (F). The top
of each Side Panel is smooth and the bottom has a notch routed in the inside edge.
Attach a Side Panel to each side of the Center Support and using a phillips screwdriver, rotate each Cam (H) clockwise until
tight (See Detail - B).
Diagram 4
F
Top
Smooth
E
I
Detail -B
H
E
Bottom
Notched
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 - Attaching NFCD Top Panel
Stand the unit up so that the notched bottom of each Side Panel is facing down and the smooth top edge is facing up.
Tap a Plastic Dowel Pin (J) into the holes in the top edge of each Side Panel (E); then, align the holes of
the NFCD Top (A) with the Dowel Pins and the slot across the NFCD Top with the Center Support (D).
Firmly press the NFCD Top onto the Dowel Pins and Side Panels, until it is firmly seated.
NOTE: Once the NFCD Top is attached, it may not be removed without causing damage.
Diagram 5
A
J
J
E
E
Step 6 - Attaching NFCD Base Assembly
Turn the assembly over so that the Top is resting on a towel or clean carpet.
Gently fit the NFCD Base (B) into the routed notches in each Side Panel (E). Rotate the NFCD Base to expose the screw
holes and using the phillips screwdriver, secure with four Wood Screws (L).
Diagram 6
L
L
B
E
E
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7 - Installing Glass Shelves
Stand the NFCD Media Tower upright. Place the Shelf Pins (M) into holes in the Side Panels where you want the Glass
Shelves (F) to be located. Each Glass Shelf requires four shelf Pins.
Place the Glass Shelves (F) in the NFCD Media Tower.
Diagram 7
M
F
Step 8 - Attach Name Plate
Attach the Sanus Name Plate (G) In the desired location.
Diagram 8
G
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (100028)
Download from Www.Somanuals.com. All Manuals Search And Download.
|