Sanus Systems Camcorder WFV44 User Guide

Assembly Instructions for Model: WFV44  
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is  
constructed of real hardwood and resonance dampening MDF.  
Safety Warning: If you do not understand these directions, or have any doubts about the  
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or  
customer service representatives can quickly assist you with installation questions and missing  
or damaged parts. Replacement parts for products purchased through authorized dealers will be  
shipped directly to you. Never use defective parts. Improper installation may cause damage or  
serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus  
Systems. Sanus Systems can not be liable for damage or injury caused by incorrect assembly, or  
incorrect use. Please call Sanus Systems before returning products to the point of purchase.  
Required Tools: Phillips screw driver  
Supplied Parts and Hardware: Some parts may be pre-assembled together*  
Hardware: Shown as actual size  
(16) Cam Pin - a  
(6) Dowel Pin - c  
(16) Dowel - d  
(16) Shelf Pin - e  
(16) Cam - b  
(8) Wood Screw - f  
(6) Spacer - g  
(4) Phillips Bolt - h  
(2) Door Handle - i*  
(8) Hinge Screw - j  
(8) Hinge Plate Screw - k  
Parts: Not Shown as actual size  
(4) Hinge - l*  
(4) Hinge Plate - m*  
(4) Back Stretcher - p  
(4) Front Stretcher - o  
(1) Top - n  
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 2: Prepare Stretchers  
Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the  
Stretchers. See Diagram 2 for assistance.  
Diagram 2  
Detailed View  
o
a
arrow  
p
Step 3: Add Stretchers  
Add the Front and Back Stretchers (o,p) to the Side Panel (u), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and  
the Dowel goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to the  
Side Panel in a clockwise motion until the stretchers are secured. Note: Front stretchers attach to the same side as the hinge  
holes are on.  
Detailed View  
Diagram 3  
u
d
hinge  
holes  
b
a
p
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 4: Add Center Panel  
Press fit the Center Panel (w) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel  
fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Center Panel. See Diagram 4  
for assistance. Note: Make sure the hinge holes on the Center Panel are on the same side as the Front Stretchers.  
Detailed View  
Diagram 4  
o
a
hinge  
holes  
w
d
Step 5: Add Stretchers  
Add the Front and Back Stretchers (o,p) to the Center Panel (w), by aligning the Cam Pin (a) with the hole which the Cams (b) point to.  
The Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to  
the Center Panel in a clockwise motion until the stretchers are secured. Note: Front stretchers attach to the same side as the  
hinge holes are on.  
Diagram 5  
Detailed View  
x
a
b
hinge  
holes  
d
p
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 6: Add Side Panel  
Press fit the Side Panel (v) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel (d)  
going into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Side Panel. See Diagram 6  
for assistance. Note: Make sure the hinge holes on the Side Panel are on the same side as the Front Stretchers.  
Detailed View  
Diagram 6  
a
hinge  
holes  
o
v
Step 7: Add Shelf Pins and Bottom Shelf  
Thread the Shelf Pins (e) into the bottom hole in the line of holes in each Panel (u,v,w). Tighten Shelf Pins with a Phillips screw driver.  
Add the Bottom Shelf (q) by inserting it into the assembly and press fit it onto the Shelf Pins. Make sure the Bottom Shelf is flush  
against the Front Stretcher (o). If there is a gap in front, shelf may be backward. See Diagram 7 for assistance. Note: Diagram 7 is a  
Back View.  
Detailed View  
Diagram 7  
w
u
e
q
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 8: Add Top  
Gently tap a Dowel Pin (c) into the holes on the top of each Panel (u,v,w). Slide a Spacer (g) over each Dowel Pin. Press fit the Top (n)  
so it fits onto the Dowel Pins. See Diagram 8 for assistance.  
Detailed View  
Diagram 8  
n
c
g
v
Step 9: Prepare Doors  
Insert each Phillips Bolt (h) through the Door (s) and into the Door Handle (i). Tighten with a Phillips screw driver. See Diagram 9a for  
assistance. The Door Panels can be interchanged by removing and re-installing the plastic border from the perimeter of the Door’s back  
side.  
Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (s). Tighten each with a Phillips screw driver. Repeat process  
until each Hinge Assembly is secure. See Diagram 9b for assistance.  
Diagram 9a  
Diagram 9b  
Detailed View  
Detailed View  
h
i
s
s
l
j
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 10: Door Install  
Position the Door (s) so the holes in the Hinge Plate (m) line up with the front pair of holes in the Side Panel (u,v). Insert a Hinge Plate  
Screw (k) through the Hinge Plate and thread it into each hole in the Side Panel. Tighten with a Phillips screw driver. Repeat process so  
each Hinge Assembly is secured. See Diagram 10 for assistance.  
Detailed View  
Diagram 10  
s
m
k
u
Step 10: Add Mid Shelves  
Thread a Shelf Pin (e) into the desired location in the Panels (u,v,w). For each shelf, four Shelf Pins will be required. Insert each Mid  
Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia-  
gram 10 for assistance. Note: Diagram 10 is a Back View.  
Detailed View  
Diagram 10  
u
v
w
e
r
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 11: Add Back Panel  
Position each Back Panel (x) up against the assembly and thread a Wood Screw (f) through it and into the Back Stretcher (p). Repeat  
process until each Back Panel is secured with four Wood Screws. Tighten each with a Phillips screw driver. See Diagram 11 for assis-  
tance.  
Detailed View  
Diagram 11  
p
f
x
Step 12: Hinge Adjustment for Woodbrook Door  
Each hinge Assembly is adjustable in multiple directions. See Diagram 12 for assistance.  
Diagram 12  
Side Adjustment  
Depth Adjustment  
Height Adjustment  
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QMotions Games Baseball game User Guide
RCA Car Video System DRC220N User Guide
RCA Conference Phone 25202RE3 User Guide
Saeco Coffee Makers Coffeemaker Giro Plus User Guide
Samsung Computer Drive SF 3100 User Guide
Samsung Flat Panel Television 244T User Guide
Samsung Microwave Oven SMH1927W User Guide
Samsung Tablet XE700T1C A01US User Guide
SanDisk Camera Accessories 80 11 00943 User Guide
Sears Lathe 36745 User Guide