SAMSUNG 700DF
Download from Www.Somanuals.com. All Manuals Search And Download.
Notational
Power
Installation
Clean
Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Disconnect the plug from the outlet
Do not disassemble
Do not touch
Grounding to prevent an electric shock
Download from Www.Somanuals.com. All Manuals Search And Download.
When not used for extended periods of time, set your PC to DPMS. If using
a screen saver, set it to the active screen mode.
z
If the size of your monitor is small, or if the same image is present for long
periods of time, you may see afterimages due to damage to the
fluorescent substance on the inside of the CRT.
Notational
Power
Installation
Clean
Do not use a damaged or loose plug.
Other
z
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet
hands.
z
This may cause an electric shock or fire.
Use only a properly grounded plug and recepticle.
z
An improper ground may cause electric shock or equipment
damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
z
Failure to do so may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or
if it is not used for a long period of time.
z
Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
This may cause a fire.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
z
Notational
Power
Installation
Clean
Put your monitor in a location with low humidity and a minimum of
dust.
Other
z
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
This may cause damage to the product or human body.
z
Place the monitor on a flat and stable surface.
The monitor can cause injury by falling.
z
Set down the monitor carefully.
It could be damaged or broken.
z
Do not place the monitor face down.
The CRT surface may be damaged.
z
Do not use the monitor without the monitor stand.
z
z
It could break down or cause a fire due to bad ventilation.
If the monitor must be used without the supplied stand, take steps
to insure proper ventilation.
Download from Www.Somanuals.com. All Manuals Search And Download.
When cleaning the monitor case or the surface of the CRT, wipe with a
slightly moistened, soft fabric.
Do not clean Flat monitor with water. Use a water-diluted mild
detergent.
Notational
Power
(Some detergents contain significant amounts of alcohol-based solvents,
which can damage (color change) or crack the monitor case. The
antiglare/anti-static surface coating on the CRT may also be affected.)
Installation
Clean
Other
Dilute the detergent (1:10 ratio) with water before using.
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
z
z
You can prevent the coated CRT from being damaged or the
monitor cabinet from being dissolved, cracked or discolored.
You can buy a recommended detergent at any Samsung Service
Center.
If the connector between the plug and the pin is dusty or dirty,
clean it properly with a dry cloth.
z
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects
on the monitor.
z
z
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug
and then contact a service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not remove cover(or back). No user serviceable parts inside.
z
z
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
Notational
Power
Installation
Clean
Other
If your monitor does not operate normally - in particular, if there are
any unusual sounds or smells coming from it - unplug it
immediately and contact an authorized dealer or service.
z
This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor.
This may cause an electric shock or a fire.
z
For each hour of looking at the monitor, you should let your eyes
rest for 5 minutes.
z
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
This may cause an explosion or fire.
z
Do not try to move the monitor by pulling on the wire or the signal
cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
z
Keep the monitor away from any magnetic substances.
This may cause discoloring or distortion of the image.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor and Stand
Power Cord
Stand
Unpacking
Front
Rear
Bottom
Quick Setup Guide
(Some models include a stand attached. )
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Warranty Card
(Not available in all locations)
User's Guide and
Driver Installation CD
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Front
Rear
Bottom
Use this button to Exit the active menu or the OSD.
1. Exit button
These buttons allow you to highlight and adjust items in the menu.
Use this button to open the OSD and activate a highlighted menu item.
2,3. Adjust buttons
4. Menu button
5. Power indicator
This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments.
Use this button to turn the monitor on and off.
6. Power button
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.
Note:
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Front
Rear
Bottom
(The configuration at the back of the monitor may vary from product to product.)
Connect the power cord for your monitor to the power port on the back of
the monitor.
1. Power port
Connect the signal cable to the video port on your computer, video board,
video card, or graphics card.
2. Signal Cable
See Connecting Your Monitor for further information regarding cable connections.
Note:
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Front
Rear
Bottom
Connect the signal cable to the video port on your computer, video board,
video card, or graphics card.
1. Signal Cable
2. Power port
Connect the power cord for your monitor to the power port on the back of
the monitor.
You can separate the base from the monitor.
3. Tilt/Swivel Base
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting
Your Monitor
Installing the
Monitor Driver
Base Installation
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the video port on your computer, video board, video card, or
graphics card.
3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the
pins on your adapter(Adapter not included). A PC-compatible computer does not need an
adapter.
4. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your
Monitor
Installing the
Monitor Driver
Base Installation
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/
Windows ME
1. Insert CD into the CD-ROM driver.
2. Click
.
"Windows ME Driver"
3. Choose your monitor model in the model list, then click the
button.
"OK"
4. Click the "
" button in the "
Install
" window.
Warning
5. Monitor driver installation is completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP/2000
Connecting Your
Monitor
Installing the
Monitor Driver
Base Installation
1. Insert CD into the CD-ROM driver.
2. Click
.
"Windows XP/2000 Driver"
3. Choose your monitor model in the model list, then click the
button.
"OK"
4. Click the "
" button in the "
Install
" window.
Warning
5. If you can see following
window, then click the
button.
"Continue Anyway"
"Message"
Then click
button.
"OK"
This monitor driver has been applied to Microsoft for the Windows logo, and this
installation does not damage the correct operation of your system. The Windows logo
certified driver will be posted on SAMSUNG Monitor Homepage in the future then you can
download it.
6. Monitor driver installation is completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux
Connecting Your
Monitor
Installing the
Monitor Driver
Base Installation
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/
®
®
Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "
" —> "
" then click the "
" Icon.
Appearance and Themes
Start
Control Panel
3. Click "
" icon and choose the "
Display
" tab then click "
Settings
".
Advanced..
4. Click the "
" button on the "
" tab and select "
Monitor
" tab.
Driver
Properties
5. Click "
" and select "
" then click "
" button.
Next
Update Driver..
Install from a list or..
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select "
" then click "
Don't search ,I will..
" and then click "
".
Have disk
Next
7. Click the "
" button then choose A:(D:\Driver) and choose your monitor model in the
Browse
model list and click the "
" button.
Next
8. If you can see following "
" window, then click the "
" button. Then
Continue Anyway
Message
click "
" button.
OK
This monitor driver has been applied to Microsoft for the Windows logo, and this installation
does not damage the correct operation of your system. The Windows logo certified driver will
be posted on SAMSUNG Monitor Homepage in the future then you can download it.
9. Click the "
" button then click "
" button continually.
Close
OK
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Monitor driver installation is completed.
®
®
Microsoft Windows 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "
" button on the "
Browse
" window.
OK
2. Click the "
Insert disk
" button on the "
" window.
File Needed
3. Choose A:(D:\Driver) then click the "Open" button and then click "
" button.
OK
How to install
1. Click "
2. Double click the "
3. Choose the "
4. Choose "
" , "
" , "
".
Start
Setting
Display
" tab and then click "
Control Panel
" Icon.
".
Advanced..
Settings
".
Monitor
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
5. Click "
6. Choose "
" and then click on "
" then click on the "Next" button.
Driver
Update Driver..
Display a list of the known drivers for this device so that I can choose a
" then click "
" and then click "
Next
".
specific driver
Have disk
7. Click the "
8. Click the "
" button then choose A:(D:\Driver).
Browse
" button, then click "
" button.
OK
Open
9. Choose your monitor model and click the "
" button then click "
Next
" button.
Next
10. Click the "
" button then the "
" button.
Finish
Close
If you can see the "
" window then click the "
"button.
Yes
Digital Signature Not Found
And click the "
" button then the "
" button.
Finish
Close
®
®
Microsoft Windows Millennium Operating System
1. Click "
" , "
Display
" , "
Control Panel
" icon.
".
Start
2. Double click "
Setting
3. Select the "
4. Select the "
" tab and click "
" button.
Settings
" tab.
Advanced Properties
Monitor
" button in the "
5. Click the "
" area.
Change
Monitor Type
".
6. Choose "
7. Choose "
8. Click the "
Have Disk
9. Specify A:\(D:\driver) then click "
Specify the location of the driver
Display a list of all the driver in a specific location..
" button
" then click "
" button.
Next
" button.
OK
" and choose the monitor that corresponds to the one you
10. Select "
Show all devices
connected to your computer and click "
".
OK
OK
" button and "
11. Continue choosing "
" button until you close the Display Properties
Close
dialogue box.
(You can get some other screen for warning message or others, then click the appreciate
option for your monitor.)
Download from Www.Somanuals.com. All Manuals Search And Download.
®
®
Microsoft Windows NT Operating System
1. Click , and then double-click
,
,
icon.
Display
Start Settings Control Panel
2. In Display Registration Information window, click Settings Tab and then click
All Display
.
Modes
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click
.
OK
button if you see the screen working normally after clicking Test. If the screen
4. Click
Apply
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
: If there is no Mode at , select the level of resolution and vertical
Note
All Display Modes
frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1. Press Enter at the first and the second screen after executing the X86Config file.
2. The third screen is for
.
setting your mouse
3. Set a mouse for your computer.
4. The next screen is for
.
selecting a keyboard
5. Set a Keyboard for your computer.
6. The next screen is for
.
setting your monitor
for your monitor. (You can enter the frequency
7. First of all, set a
directly.)
horizontal frequency
8. Set a
for your monitor. (You can enter the frequency directly.)
vertical frequency
9. Enter the
. This information will not affect the actual
model name of your monitor
execution of X-Window.
10. You have
setting up your monitor.
finished
X-Window after setting other requested hardware.
Execute
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilt/Swivel Base | Attaching and Removing the Base
Connecting Your
Monitor
Installing the
Monitor Driver
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable
viewing angle.
Base Installation
The base is detachable.
Note:
If your monitor was supplied with the base detached, attach the base as follows.
Remove the twist-tie before attaching the base to the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your
Monitor
Installing the
Monitor Driver
Base Installation
Attaching the Base
1. Place the monitor upside-down on a flat work surface.
2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.
3. Press the base onto the monitor until the tabs are fully engaged in the slots.
4. Push the base toward the front of the monitor until the release latch clicks into the locked
position.
* Do not bend the snap.
Removing the Base
5. Squeeze and pull up on the release latch on the base.
6. Push the base toward the back of the monitor and lift up to remove the base.
The base will align with the monitor slots in only one position.
Note:
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display (OSD) Menu System
Use this button to Exit the active menu or the
1 Exit button:
OSD.
These buttons allow you to highlight and
adjust items in the menu.
Use this button to open the OSD and activate
a highlighted menu item.
2,3 Adjust buttons:
4 Menu button:
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Check List
Solutions
Is the power cord connected
properly?
Check the power cord connection
and supply.
No images on the
screen. I cannot
turn on the monitor.
Check List
Q & A
Check the signal cable connection.
Can you see "No Connection,
Check Signal Cable" on the
screen?
Self-Test Feature
Check
If the power is on, reboot the
computer to see the initial
screen(the login screen), which
can be seen.
If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows) and then change
the frequency of the video card.
(Refer to the Preset Timing Modes)
You can see this message when the
signal from the video card exceeds
the maximum resolution and
frequency that the monitor can
properly handle.
Can you see "Sync. Out of
Range" on the screen?
Adjust the maximum resolution and
frequency that the monitor can
properly handle.
There is no image on the
screen. Is the power indicator
on the monitor blinking at 1
second intervals?
The monitor is in PowerSaver mode.
Press a key on the keyboard or
move the mouse to activate the
monitor and restore the image on the
screen.
Unlock the OSD by pressing the
MENU button for at least 10
seconds.
I cannot see the On
Screen Display.
Have you locked the On
Screen Display (OSD) Menu to
prevent changes?
Check the monitor configuration
to see if it is in Interlace Mode.
(Interlace Mode: Vertical
The signal from the video card
exceeds the maximum resolution
and frequency of the monitor.
The image on the
screen is shaking.
frequency 43Hz, 87Hz(i), etc)
Are there any magnetic
products such as a power
adapter, speaker or a high
voltage wire near by?
Move the monitor away from
anything that can create a strong
magnetic field.
Is the voltage stable?
The screen image can appear to
shake or vibrate at a particular time
of day due to low supply voltage.
The screen image can also appear to shake or vibrate if there is a
problem with the video card or the computer's main board.
Download from Www.Somanuals.com. All Manuals Search And Download.
Is the screen displaying only
one color as if looking at the
screen through a cellophane
paper?
Check the signal cable connection.
The screen shows
strange colors or
just black and
white.
Check List
Make sure the video card is fully
inserted in it's slot.
Q & A
Self-Test Feature
Check
Have the screen colors become
strange after running a program
or due to a crash between
applications?
Reboot the computer.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
Have you changed the video
card or the driver?
Adjust screen image position and
size using the OSD.
The screen
suddenly has
become
unbalanced.
Have you adjusted the
resolution or frequency to the
monitor?
Adjust the resolution and frequency
at the video card.
(Refer to the Preset Timing Modes).
The screen can be unbalanced due to the cycle of the video card
signals. Readjust Position by referring to the OSD.
Have you adjusted the
resolution or frequency on the
monitor?
Adjust the resolution and frequency
of the video card.
(Refer to the Preset Timing Modes).
The screen is out of
focus or OSD
cannot be adjusted.
Are there any magnetic
products such as an adapter,
speaker or a high voltage wire
near the monitor?
Enter the OSD and perform a
"Degauss".
The screen is
partially distorted.
Keep the monitor away from any
magnetic products.
Is the frequency properly
adjusted when checking the
Display Timing on the menu?
Adjust the frequency properly by
referring to the video card manual
and the Preset Timing Modes.
LED is blinking but
no images on the
screen.
(The maximum frequency per
resolution may differ from product to
product.)
Have the Windows colors been
set properly?
For Windows XP/2000:
Set the colors properly at the
Control Panel, Display, Settings.
There are only 16
colors shown on the
screen. The screen
colors have
changed after
changing the video
card.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Check the following items if there is trouble with the monitor.
Check List
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
Q & A
Self-Test Feature
Check
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "Control Panel, System, Device Administrator" and then
reboot the computer to reinstall the adapter (video) driver.
Note: If problems repeatedly occur, contact an authorized service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
How can I change the frequency?
Frequency can be changed by reconfiguring the video
card.
Check List
Q & A
Self-Test Feature
Check
Note that video card support can vary, depending on the
version of the driver used.
(Refer to the computer or the video card manual for
details.)
How can I adjust the resolution?
Windows XP/2000: Set the resolution at the
Control Panel, Display, Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows XP/2000: Set the function at BIOS-
SETUP of the computer or the screen saver. (Refer to
Windows/Computer Manual).
The monitor makes a sound when it
is turned on.
This is normal as some sound may be generated when
the metal case and the electromagnet, which are
installed to block any electromagnetic waves, interact
with each other.
How can I clean the outer
case/Picture tube?
Disconnect the power cord and then clean the monitor
with a soft cloth, using either a cleaning solution or plain
water.
Do not leave any remains of the detergent nor scratch
the case. Do not allow any water to go inside the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your monitor provides a self test feature that allows you to check whether your monitor is
functioning properly.
Check List
Q & A
Self-Test
Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If your monitor works normally, the following screen appears.
Failure of any of the boxes to appear indicates a problem with your monitor. This box
also appears during normal operation if the video cable becomes disconnected or
damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your
video controller and computer system; your monitor is functioning properly.
If there is something wrong with the input signal, a message appears on the screen or
the screen goes blank although the power indicator LED is still on. The message may
indicate that the monitor is out of scan range or that you need to check the signal cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
The location and the position of the monitor may influence the quality and other
features of the monitor.
Check List
Q & A
there are any woofer speakers near the monitor, unplug and relocate the woofer to another
room.
Self-Test
Feature Check
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3
feet (one meter) of the monitor.
3. Degauss the monitor if any devices were removed from the area.
z
z
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the
PC or the video card, this can cause the monitor to become blank, have poor coloring, noise,
Sync. Out of Range, etc. In this case, first check the source of the problem, and then contact
a service center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or an "Sync. Out of Range" message comes up,
disconnect the cable from the computer while the monitor is still powered on.
{
If there is a message coming up on the screen or if the screen goes white, this means
the monitor is in working condition.
{
In this case, check the computer for trouble.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
Picture Tube
Type
SAMSUNG 700DF
General
17"(43cm) DynaFlat X (40.6cm viewable)
PowerSaver
Preset Timing
Modes
Deflection angle
Dot Pitch
90 °
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1280 Dots, 1024 Lines
Active Display
Horizontal
312 ± 4 mm
234 ± 4 mm
Vertical
Synchronization
Horizontal
30 ~ 70 kHz
50 ~ 160 Hz
Vertical
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
110 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
90W (Maximum), 80W (Nominal)
Dimensions (WxDxH)
398 x 412 x 400mm (with Stand)
Weight
15.7 kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power-off Mode EPA/ENERGY
State
Normal Operation
2000
Power Indicator
Power Consumption
Green
Green, Blinking
80W(Nominal)
90W(Maximum)
Less than 2W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when
used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product meets
®
the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
General
PowerSaver
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
Preset Timing
Modes
IBM, 640 x 480
31.469
31.469
37.500
43.269
53.674
68.677
59.940
70.087
75.000
85.008
85.061
84.997
25.175
28.322
31.500
36.000
56.250
94.500
-/-
-/+
-/-
IBM, 720 x 400
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 1024 x 768
-/-
+/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
Service
Terms
BRAZIL :
Regulatory
Natural Color
Authority
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421
CANADA :
Samsung Electronics Canada Inc.
Samsung Customer Care
7037 Financial Drive
Mississauga, Ontario
L5N 6R3
1-800-SAMSUNG (1-800-726-7864)
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
e-mail : [email protected]
ESPAÑA :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
GERMANY :
TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0.12/Min
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
Download from Www.Somanuals.com. All Manuals Search And Download.
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
Service
Terms
Regulatory
Natural Color
Authority
MEXICO :
SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V.
Saturno NO.44, Col. Nueva Industrial Vallejo
Gustavo A.Madero C.P.07700, Mexico D.F. Mexico
TEL. 52-55-5747-5100
Fax. 52-55-47 52 02
RFC: SEM950215S98
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
PERU
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
o
Rua Mário Dioniso, N 2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Free Line 800 220 120
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
THAILAND :
HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Terms
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
Regulatory
Natural Color
Authority
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
U.S.A. :
Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V.
Saturno NO.44, Col. Nueva Industrial Vallejo
Gustavo A.Madero C.P.07700, Mexico D.F. Mexico
TEL. 52-55-5747-5100
EXPORTADO POR: Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong-gu,
Suwon City, Kyoungki-Do Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
Unit: mm
Service
Vertical Frequency
Terms
The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh
Rate. Unit: Hz
Regulatory
Natural Color
Authority
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this
case, flickering of the screen can be detected. To avoid this problem, there is a
Flicker-free Mode using a vertical frequency over 70 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is
called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-
Interlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of monitors to ensure a clear image.
The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and
the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal
dots (horizontal resolution) and 768 vertical lines (vertical resolution).
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Information | IC Compliance Notice | MPR II Compliance |
European Notice (Europe only) | PCT Notice | VCCI |
TCO'95-Ecological requirements for personal computers (TCO applied model only)
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Service
Terms
FCC Information
Regulatory
Natural Color
Authority
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the
following warning:
This equipment has been tested and found to comply with the limits for a Class B digital
Note:
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television receptions, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
z
z
z
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
z
User Information
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. If necessary, consult your dealer or an
experienced radio/television technician for additional suggestions. You may find the booklet called
How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared
by the Federal Communications Commission. It is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Tel) 949-975-7310
Fax) 949-922-8301
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It
may be suitable for connection to any UL Listed personal computer with similar configuration.
Before making the connection, make sure the voltage rating of the computer convenience outlet is
the same as the monitor and that the ampere rating of the computer convenience outlet is equal to
or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-
15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable
power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les
équipements produisant des interférences au Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
MPR II Compliance
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and
magnetic fields.
European Notice(Europe Only)
Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC),
(93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the
European Community.
Compliance with these directives implies conformity to the following European Norms:
z
z
z
z
EN55022:1998+A1:2000 - Radio Frequency Interference
EN55024:1998 - Electromagnetic Immunity of Information Technology Equipment
EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics
EN61000-3-3:1995 - Voltage Fluctuations
PCT Notice
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in
a domestic environment, it may cause radio interference. Install and use the equipment according
to the instruction manual.
TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice
has provided you with a product developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and to the further development of
environmentally-adapted electronic products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment.The main problem as far as monitors and
other electronic equipment are concerned is that environmentally harmful substances are used
both in the products and during their manufacture. Since it has not been possible so far for the
majority of electronic equipment to be recycled in a satisfactory way, most of these potentially
damaging substances sooner or later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are
important from both the working and natural environment viewpoints. Since all types of
conventional electricity generation have a negative effect on the environment (acidic and climate-
influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
in offices consumes an enormous amount of energy, since it is often routinely left running
continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and
Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of
heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated
solvents. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan, which must be adhered to in each country where the company conducts its
operations policy. The energy requirements include a demand that the monitor after a certain
period of inactivity shall reduce its power consumption to a lower level, in one or more stages. The
length of time to reactivate the monitor shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example in respect of the
reduction of electric and magnetic fields, along with physical and visual ergonomics and good
usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by
this product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): [email protected]
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and
housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer
casing can consist of flame retardant substances. These are related to another group of
environmental toxins, PCBs, which are suspected to give rise to similar harm, including
reproductive damage in fish eating birds and mammals, due to the bioaccumulative processes.
Flame retardants have been found in human blood and researchers fear that disturbances in
foetus development may occur.
z
TCO'95 demand requires that plastic components weighing more than 25 grams must not
contain organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been
developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous
system and is toxic in high doses.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of mercury. It also demands that no mercury is present in any of the electrical or electronics
components concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in
the stratosphere, causing increased reception on Earth of ultraviolet light with consequent
increased risks of skin cancer (malignant melanoma).
Download from Www.Somanuals.com. All Manuals Search And Download.
z
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the
manufacturing of the product or its packaging.
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you
with a product developed for professional use. Your purchase has also contributed to reducing the
burden on the environment and also to the further development of environmentally adapted
electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was
developed as a joint effort by the TCO(The Swedish Confederation of Professional Employees),
Svenska Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens
Energimyndighet(The Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of
electric and magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment. The main problem, as far as computers
and other electronics equipment are concerned, is that environmentally harmful substances are
used both in the products and during their manufacture. Since it is not so far possible to
satisfactorily recycle the majority of electronics equipment, most of these potentially damaging
substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics
equipment in offices is often left running continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The
Swedish Society for Nature Conservation). These demands impose restrictions on the presence
and use of heavy metals, brominated and chlorinated flame retardants, CFCs(freons)and
chlorinated solvents, among other things. The product must be prepared for recycling and the
manufacturer is obliged to have an environmental policy which must be adhered to in each
country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The
length of time to reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The
complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO'99 approved and labelled products may also be obtained via
the Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their
purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer
casing can consist of flame retardant substances. Most flame retardants contain bromine or
chloride, and those flame retardants are chemically related to another group of environmental
toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are
suspected of giving rise to severe health effects, including reproductive damage in fish-eating
birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found
in human blood and researchers fear that disturbances in foetus development may occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams
must not contain flame retardants with organically bound bromine or chlorine. Flame retardants
are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses. The
relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens
and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and
is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any
mercury. It also demands that mercury is not present in any of the electrical or electronics
components associated with the labelled unit. There is however one exception. Mercury is, for the
time being, permitted in the back light system of flat panel monitors as today there is no
commercially available alternative. TCO aims on removing this exception when a Mercury free
alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed
circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere,
causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer
(malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement
permits the inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)
Congratulations!
The display you have just purchased carries the TCO'03 Displays label. This means that your
display is designed, manufactured and tested according to some of the strictest quality and
environmental requirements in the world. This makes for a high performance product, designed
with the user in focus that also minimizes the impact on our natural environment.
Some of the features of the TCO'03 Display requirements:
Ergonomics
Download from Www.Somanuals.com. All Manuals Search And Download.
Good visual ergonomics and image quality in order to improve the working environment for the
user and to reduce sight and strain problems. Important parameters are luminance, contrast,
resolution, reflectance, colour rendition and image stability.
Energy
z
Energy-saving mode after a certain time-beneficial both for the user and the environment
Electrical safety
z
Emissions
z
z
Electromagnetic fields
Noise emissions
Ecology
z
z
The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 000
Restrictions on
o chlorinated and brominated flame retardants and polymers
o heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in cooperation
with scientists, experts, users as well as manufacturers all over the world. Since the end of the
1980s TCO has been involved in influencing the development of IT equipment in a more user-
friendly direction. Our labelling system started with displays in 1992 and is now requested by
users and IT-manufacturers all over the world.
For more information, Please visit
TCO'03 Recycling Information (TCO'03 applied model only)
[European Residents Only]
For recycling information for TCO'03 certified monitors, for the residents in the following countries,
please contact the company corresponding to your region of residence. For those who reside in
other countries, please contact a nearest local Samsung dealer for recycling information for the
products to be treated in environmentally acceptable way.
[U.S.A. Residents Only]
U.S.A.
[European Residents Only]
NORWAY
SWEDEN
GERMANY
vfw AG
Solid Waste Transfer &
Recycling Inc
COMPANY
ADDRESS
ELKRETSEN
Elektronikkretur AS
ELKRETSEN Box
1357, 111 83
Stockholm
Max Plank Strasse 42
50858 Collogne
Germany
442 Frelinghuysen Ave
Newark, NJ 07114
6454 Etterstad 0602 Oslo
Fyrstikkalln 3B
Barnhusgatan 3, 4 tr.
TELEPHONE 973-565-0181
08-545 212 90
08-545 212 99
23 06 07 40
23 06 07 41
49 0 2234 9587 - 0
FAX
Fax: 973-565-9485
none
E-
MAIL
HOME
PAGE
Waste_Disposal.htm kretsen.se/
Download from Www.Somanuals.com. All Manuals Search And Download.
Natural Color Software Program
Service
Terms
Regulatory
Natural Color
Authority
One of the recent problems in using a computer is that the color of the images printed out by a
printer or other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the
color of the images on the monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial
screen of the program installation will be executed. Click Natural Color on the initial screen to
install the Natural Color software. To install the program manually, insert the CD included with
the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then
select [Execute].
Enter D:\color\eng\setup.exe and then press the key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a
program].
Select Natural Color from the list and then click the [Add/Delete] button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Information in this document is subject to change without notice.
© 2003 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.
Service
Terms
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Regulatory
Natural Color
Authority
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an
ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein
may be the trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|