MX-HS8500
PREMIUM HI-FI Component System
user manual
imagine the possibilities
Thank you for purchasing this Samsung
product.
To receive more complete service,
please register your product at
This Nanum Gothic Eco font is provided by NAVER.
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
1
2014-05-23 오후 2:42:59
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
FCC NOTES (for U.S.A)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on.
9. Do not defeat the safety purpose of
the polarized or groundingtype plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
If interference is present, the user is
10. Protect the power cord from being walked
on or pinched particularly at plugs,
encouraged to try to correct the interference
by one or more of the following measures:
convenience receptacles, and the point
where they exit from the apparatus.
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect this equipment to an outlet that is
on a circuit that is different than the circuit
the receiver is connected to.
•
•
11. Only use attachment/accessories specified
by the manufacturer.
•
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold
with the apparatus.
When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Consult the dealer or an experienced
radio/TV technician for help.
This class B digital product meets all
requirements of the Canadian Interference -
Causing Equipment Regulations.
•
Important Safety Instructions
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below. Keep these operating
instructions handy for future reference.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
3
2014-05-23 오후 2:43:00
Safety Information
Place the loudspeakers at a reasonable
distance on either side of the system to
ensure good stereo sound.
Direct the loudspeakers towards the listening
area.
Do not expose this apparatus to dripping or
splashing. Do not place objects filled with
liquids, such as vases, on the apparatus.
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power
plug must be readily accessible at all times.
•
Precautions
Ensure that the AC power supply in your
house complies with the identification sticker
located on the back of your product.
•
•
•
Install your product horizontally, on a
•
suitable base (furniture), with enough space
around it for ventilation (3 - 4 inches/7.5 -
10 cm).
•
•
Do not place the product on amplifiers or
•
other equipment which may become hot.
Make sure the ventilation slots are not
covered.
Do not stack anything on top of the product.
Before moving the product, ensure the Disc
Insert Slot is empty.
To turn off the product completely,
disconnect the AC plug from the wall outlet.
Disconnect the AC plug from the wall outlet
if you will leave the device unused for a long
period of time.
During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage spikes due
to lightning could damage the product.
Do not expose the product to direct sunlight
or other heat sources. This could cause the
product to overheat and malfunction.
Protect the product from moisture, excess
heat, and equipment creating strong
magnetic or electric fields (i.e. speakers.).
Disconnect the power cable from the AC
Use only a properly grounded plug and
receptacle.
•
An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
•
-
•
Disc Storage & Management
Holding Discs
•
•
Fingerprints or scratches on
-
a disc may reduce sound
and picture quality or cause
skipping.
•
Avoid touching the surface of a disc where
data has been recorded.
-
•
Hold the disc by the edges so that
fingerprints will not get on the surface.
-
Do not stick paper or tape on the disc.
Cleaning Discs
-
•
•
•
supply if the product malfunctions.
Your product is not intended for industrial
use. It is for personal use only.
Condensation may occur if your product or
disc has been stored in cold temperatures. If
transporting the product during the winter,
wait approximately 2 hours until the product
has reached room temperature before using.
If you get fingerprints or dirt
-
•
on a disc, clean it with a mild
detergent diluted in water and
wipe with a soft cloth.
•
When cleaning, wipe gently from the
inside to the outside of the disc.
-
Disc Storage
Do not keep in direct sunlight.
Keep in a cool ventilated area.
Keep in a clean protection jacket and
store vertically.
`
`
`
The batteries used with this product
•
contain chemicals that are harmful to the
environment. Do not dispose of batteries in
the general household trash.
Please check the volume level before playing
not to startle the elderly, infirm and pregnant
woman at a sudden loud sound.
•
4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
4
2014-05-23 오후 2:43:01
Disc and Format Compatibility
Supported Audio Formats
This product does not support Secure (DRM)
Media files.
File
Extension
Audio
Codec
Sampling
Rate
Bit Rate
CD-R Discs
16KHz ~ 80Kbps ~
48KHz 320Kbps
MPEG 1
Layer3
Some CD-R discs may not be playable
•
16KHz ~ 80Kbps ~
48KHz 320Kbps
MPEG 2
Layer3
depending on the disc recording device (CD-
Recorder or PC) and the condition of the
disc.
*.mp3
*.wma
16KHz ~ 80Kbps ~
48KHz 320Kbps
MPEG 2.5
Layer3
Use 650MB/74 minute CD-R discs.
Do not use CD-R discs over 700MB/80
minutes as they may not be played back.
•
16KHz ~ 56Kbps ~
48KHz 128Kbps
Wave_Format_MSAudio1
Some CD-RW (Rewritable) media may not
be playable.
•
16KHz ~ 56Kbps ~
48KHz 128Kbps
Wave_Format_MSAudio2
Only CD-Rs that are properly "closed" can be
•
fully played. If the session is closed, but the
disc is left open, you may not be able to fully
play the disc.
NOTES
|
|
Does not support WMA Professional codec.
✎
✎
The above table shows supported sampling
rates and bit rates. Files in formats that are
not supported will not play.
MP3-CD Discs
Only CD-R discs with MP3 files in ISO 9660
or Joliet format can be played.
•
MP3 file names should contain no blank
spaces or special characters (. / = +).
•
Use discs recorded with a compression/
decompression data rate greater than
128Kbps.
•
Only a consecutively written multisession disc
•
can be played. If there is a blank segment in
the Multisession disc, the disc can be played
only up to the blank segment.
If the disc is not closed, it will take longer to
begin playback and not all of the recorded
files may play.
•
For files encoded in the Variable Bit Rate
•
(VBR) format,( i.e. files encoded in both
low bit rate and high bit rate - 32Kbps
~ 320Kbps), the sound may skip during
playback.
A maximum of 999 files can be played per
CD.
•
5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
5
2014-05-23 오후 2:43:01
Contents
Playing USB Devices
15
15
15
16
16
16
16
16
Safety InformatIon
USB Device Playback
Warning
2
4
4
5
5
To Select a File from a USB Device
To Use High Speed Search
To Delete a File
Precautions
Disc Storage & Management
Disc and Format Compatibility
Supported Audio Formats
To Move to the Next/Previous Folder
To safely remove a USB device
Read Before Connecting USB Storage
Devices
GettInG Started
Searching for a Track Quickly
Using the Program Function
Viewing or Editing Programmed Tracks
Bluetooth
17
17
17
18
18
18
Front Panel
8
Rear Panel
9
Remote Control
10
11
11
11
12
12
12
What is Bluetooth?
Accessories
To connect the Hi-Fi Component to a
Bluetooth device
Connecting the Speakers
Cautions on Moving the Speakers
Moving the Speaker Set
Moving the Right Speaker set
Moving the Left Speaker
To disconnect the Bluetooth device from
the Hi-Fi Component
19
19
To disconnect the Hi-Fi Component
from the Bluetooth device
Using Bluetooth Power On
19
20
20
TV SoundConnect
To connect the Hi-Fi Component to a
SoundConnect Compatible Samsung TV
functIonS
The Display function
Changing Display mode
The DEMO function
Playing a CD
To disconnect the TV from the Hi-Fi
Component
13
13
13
13
13
13
14
14
20
20
To disconnect the Hi-Fi Component
from the TV
Using My Karaoke
20
21
22
22
22
Loading a Compact Disc
CD/MP3/CD-R Playback
Selecting a Track
Auto Change Function
Listening to the Radio
To Store the Stations You Want
Selecting a Stored Station
Searching for a Specific Music Passage
on a CD
Repeat One or All Tracks on a CD
14
6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
6
2014-05-23 오후 2:43:01
Timer Function
22
22
22
24
24
24
25
26
26
26
26
27
27
27
28
28
28
28
Setting the Clock
Setting the Timer
Cancelling the Timer
The Recording Function
Basic Recording
Recording Speed
Special Sound Effects
Selecting EQ Mode
FOOTBALL MODE function
GOAL Function
GIGA SOUND Function
BEAT WAVING Function
DJ BEAT Function
+PANNING Funcion
NON-STOP MUSIC RELAY Function
DANCE TIME Function
TEMPO Function
appendIx
Troubleshooting
Specifications
29
30
7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
7
2014-05-23 오후 2:43:02
Getting Started
Front Panel
1
2 35467890! #$
%^
@
m
l
&
*
(
)
k
j
ihgf decb
a
TEMPO button
SEARCH button
USB REC button
ENTER button
Display Panel
(
)
a
b
c
d
e
f
g
h
1
DANCE TIME button
TV SOUNDCONNECT button
CD/ Bluetooth button
STOP button
2
3
4
5
6
7
8
9
0
!
@
#
$
%
+PANNING button
EQ button
BACKWARD SEARCH/SKIP button
GIGA SOUND BEAT button
DISC slot
PROGRAM button
USB 2 jack for Playing and USB Recording
MIC jack
TUNER/AUX button
REMOTE CONTROL SENSOR
AUX IN 1 jack
Use to connect an external device such
as an MP3 player.
PLAY/PAUSE button
FORWARD SEARCH/SKIP button
Eject button for Disc
NON-STOP MUSIC RELAY button
VOLUME / DJ button
Connect AUX IN 1 on the front panel
of the product to the Audio Out of an
external device/MP3 player.
•
i
VOLUME/SEARCH JOG
POWER button
Press the TUNER/AUX button to
select AUX1.
•
^
Press this button to switch your
USB 1 jack for only Playback
USB button
•
j
k
l
m
product on or off.
DISPLAY / DEMO button
DJ BEAT button
&
*
FOOTBALL MODE button
BEAT WAVING button
8
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
8
2014-05-23 오후 2:43:03
Rear Panel
1
2
3
4 5 67
AUX IN 2 Terminals
Cooling fan
The fan operates while the unit is
powered on.
•
1. Use an Audio Cable (not supplied)
to connect AUX IN 2 on the product
to Audio Out on an external analog
output device.
If you set the unit to the minimum
volume, the fan won't operate.
Secure a minimum 6 inches (15 cm)
of clear space on from all sides of the
fan when installing the product.
1
2
Be sure to match connector colors.
If the external analog output device
has only one Audio Out jack, connect
either left or right.
•
•
6
POWER
Press the TUNER/AUX button to
select AUX 2.
•
Insert only the provided power cable.
•
If the product is in AUX mode for
more than eight hours and no
•
2.2 CH Speaker Terminals
1. To achieve the correct sound quality,
when you connect the speakers,
match the color of the speaker plugs
to the color of the speaker jacks. See
below.
buttons on the front panel or remote
are pushed, the system will turn off.
FM Antenna Terminals
1. Connect the FM antenna to the FM
antenna connector terminal.
3
LEFT channel (marked , White/
Purple).
•
2. Slowly move the antenna wire until you
find a location where reception is good,
then fasten it to a wall or other rigid
surface.
3. If reception is poor, you may need
to install an outdoor antenna. To do
so, connect an outdoor FM antenna
to the FM socket on the rear of the
system using a 75Ω coaxial cable (not
supplied).
RIGHT channel (marked , Red/
Purple).
•
7
Don't force the Purple SUBWOOFER
connector into the White or Red
speaker jack.
•
LED Terminals for Speaker Beat Waving.
ONLY FOR SERVICE
4
5
This jack is for testing only. Please do
not use.
•
9
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd
9
2014-05-23 오후 2:43:03
Getting Started
Remote Control
MUTE (Turn off the sound temporarily.
Press again to turn the sound back on.)
Power
BEAT WAVING
Bluetooth
CD
TV SoundConnect
USB REC
REC SPEED
USB
TUNING MODE
MO/ST
TUNER/AUX
+PANNING
DJ BEAT
NON-STOP MUSIC RELAY
EFFECT LEVEL
TEMPO
SKIP
SEARCH
REPEAT
PLAY/PAUSE
STOP
GIGA SOUND BEAT
GOAL
FOOTBALL
EQ
DANCE TIME
TUNING/ALBUM
DELETE
,
VOLUME (–, +)
PROGRAM
, .
SLEEP (Set a sleep time to shut off the
product.)
TIMER SET
TIMER ON/OFF
DISPLAY
AUTO CHANGE
MY KARAOKE
MIC VOLUME –, +
Installing Batteries In The Remote Control
Place batteries in the remote control so they
•
match the polarity of the illustrations in the
battery compartment. : (+) to (+) and (–) to
(–).
Do not dispose of batteries in a fire.
Do not short circuit, disassemble, or overheat
the batteries.
•
•
There is a danger of explosion if the battery
•
is replaced with the wrong battery type.
Replace only with the same or equivalent
type.
The remote control can be used up to
approximately 23 feet (7 meters) in a
straight line from the system.
•
10
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 10
2014-05-23 오후 2:43:04
Accessories
Check for the supplied accessories below.
User Manual
Remote Control / Batteries
(AH68-02706A)
(AH59-02613A/4301-000116)
FM Antenna
Power Cable
(AH42-00021A)
(3903-000467)
Figures and illustrations in this user's manual are provided for reference only and may differ
from actual product appearance.
•
Connecting the Speakers
Cautions on Moving the Speakers
Recommended speaker setup.
When moving the main unit and speakers,
make sure to separate all connected speaker
cables before.
When separating the SPEAKERS LIGHTING
cables, press the lock to release the
connector as shown below.
•
•
IMPORTANT
|
|
The product may not operate properly if
it is subject to shaking or external shocks
or if the speakers are not installed as
recommended.
✎
Do not stretch the speaker wires or place a
heavy object on them.
✎
11
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 11
2014-05-23 오후 2:43:05
Getting Started
Moving the Speaker Set
You can move and install the speaker set to the desired location.
Moving the Right Speaker set
1. To unlock the bottom wheel, pull up the lock
latch in the arrow direction.
To lock the wheel, pull down the latch.
•
2. Hold the speaker set by its top handles on
the both sides.
< Locked >
< Unlocked >
3. Lean the Speaker towards you appropriately,
and move it.
CAUTION
|
|
When leaning the speaker, stand clear to avoid crushing onto your
feet with the speaker's bottom front end.
✎
Before using the speakers, make sure to install it on an even surface
and lock its wheels.
✎
Moving the Left Speaker
1. To unlock the bottom wheel, pull up the lock
latch in the arrow direction.
To lock the wheel, pull down the latch.
•
2. Hold the speaker by its handles on the both
sides.
< Locked >
< Unlocked >
3. Lean the Speaker towards you appropriately,
and move it.
CAUTION
|
|
When leaning the speaker, stand clear to avoid crushing onto your
feet with the speaker's bottom front end.
✎
Before using the speakers, make sure to install it on an even surface
and lock its wheels.
✎
12
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 12
2014-05-23 오후 2:43:07
Functions
The Display function
Playing a CD
You can view functions available on
the display, adjust the brightness of the
display and set the Display/LED either on
or off.
Loading a Compact Disc
You can play standard compact discs that
require no adapter.
1. Insert a disc gently into the disc slot with
the disc's label facing up. The disc will be
played automatically.
Changing Display mode
Press the DISPLAY/DEMO button on the
product.
Each time you press this button, the mode will
change as follows:
You can load or unload compact discs
•
when the radio, USB, or auxiliary source
function is selected. When you press the
button, all the other functions will
change to the CD mode.
8
The Dimmer function
The Dimmer function is selected and the
display darkens.
•
If no buttons are pressed on the product
or remote control for more than 3
minutes when the product is in Pause
mode, it will change to Stop mode.
•
•
LED OFF
•
The Front display LED is turned off while the
dimmer function is working.
Clock ON
The Clock you set is displayed.
Display/LED ON
•
If no buttons are pressed on the product
or remote control for more than 25
minutes when the product is in Stop
mode, the product will turn off.
•
All displays and the LED are turned on.
The DEMO function
CD/MP3/CD-R Playback
IMPORTANT
Press the DISPLAY/DEMO button for 5 seconds
to start the Demo mode.
When you press the DISPLAY/DEMO button
while the unit is in Demo mode, the function
operates as follows:
|
|
This product is designed to play the
following audio disc types: CD, CD-R, CD-
RW.
✎
1. Insert a disc gently into the disc slot with
DIMMER LED Off (unit/speaker) --:-- [time
;
;
the disc's label facing up.
display] LED On (unit/speaker)
;
2. The disc is played automatically.
To cancel the Demo mode
For MP3/WMA files, it may take several
minutes for the product to finish
scanning the disc tracks.
•
Press the DISPLAY/DEMO again for 5
seconds. The DEMO mode is canceled and
the product turns off.
•
If you play a file with an English title, the
•
song title will be shown in the display.
(Titles in other languages can not be
displayed.)
Press the TUNER/AUX, CD/Bluetooth, or USB
button. The DEMO mode is canceled and the
mode is changed to the mode you selected.
•
An English-titled track containing a
special character (@, $, *, etc.) will not
be displayed.
•
NOTES
|
|
When the DEMO music function is on, only
the POWER ( ) and VOL buttons and the
buttons mentioned above work.
✎
<CD Playback Display>
Track Indicator
Playtime
Indicator
13
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 13
2014-05-23 오후 2:43:08
Functions
3. To adjust the volume:
Selecting a Track
Turn the VOLUME control on the
product.
•
You can select a desired track while the disc is
being played.
Press the VOL+ or VOL- button on the
remote control.
•
To play the previous track
The volume level can be adjusted in 31
steps (VOLUME MIN, VOLUME 01 ~
VOLUME 29, and VOLUME MAX).
Press the
button within 3 seconds after the
1
current track has started playing.
Press the button twice, 3 seconds or more
after the current track starts playing.
1
4. PAUSING PLAYBACK
Main Unit
To pause playback temporarily, press the
button.
To play the next track
Press the
button.
Press
disc.
again to continue playing the
2
To play the current track from the
beginning
Remote control
To pause playback temporarily, press the
button.
Press the
button, 3 seconds after the
1
Press the
the disc.
button to continue playing
current track started playing.
5. To end playing, press the
button.
5
To play the track of your choice
NOTES
|
|
Press the
track.
or
button to move to a desired
1
2
If no CD is in the disc slot, “NO DISC”
appears on the display.
✎
Searching for a Specific Music Passage
on a CD
The quality of MP3/CD-R playback may vary
depending on the condition of the disc or
the condition of the recorder used to create
the disc.
✎
When listening to a CD, you can quickly search
for a specific music passage on a track.
If a disc contains different types of files or
unnecessary folders, you will have problems
with playback.
✎
✎
Forward Search ...................
Backward Search.................
3
4
You can also press and hold the
buttons on the product to automatically scan
for a track.
,
1 2
Gently insert a CD into the disc slot. Do not
apply excessive force.
Do not apply force to the product or
place a heavy object on the product.
-
Repeat One or All Tracks on a CD
Do not insert an out-of-spec or oddly
shaped CD (heart shaped, octangular,
etc.).
-
You can play a CD or tracks on a CD
repeatedly.
1. Press the REPEAT button on the remote
control.
You can damage the product.
Carefully maintain your CDs.
-
Each time you press this button, the mode
changes as follows:
MP3 : OFF
TRACK
DIR
ALL
RANDOM
;
;
;
;
CD : OFF TRACK ALL RANDOM
;
;
;
14
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 14
2014-05-23 오후 2:43:08
2. When you want to stop the repeat
function, press the REPEAT button until
"OFF" is displayed.
To Select a File from a USB Device
You can select an MP3 file while the product is
playing.
OFF : Cancels repeat playback.
•
NOTES
|
|
TRACK : Repeatedly plays the selected
•
track.
If you want to move to the previous/next
✎
track, press the
,
buttons briefly.
DIR (DIRECTORY) : Repeatedly plays all
tracks in the selected folder.
1 2
•
The unit moves to the previous/next track
within the directory.
-
ALL : Repeatedly plays the entire disc.
•
If you press the
,
buttons more
-
1 2
RANDOM : Plays tracks in random order.
•
times than the number of the files in
the directory, the unit moves to the next
directory.
Playing USB Devices
To repeat
Connect an external storage device such as
a USB flash memory or external HDD (Hard
Disk Drive) to the product. You can play files in
MP3/WMA format.
1. Press the REPEAT button.
Each time you press this button, the mode
changes as follows:
USB Device Playback
OFF TRACK DIR ALL RANDOM
;
;
;
;
1. Connect the external USB storage device
2. When you want to stop the repeat
function, press the REPEAT button until
"OFF" is displayed.
to your product.
2. Select the USB mode by pressing the USB
button on the product or the USB button
on the remote control.
OFF : Cancels repeat playback.
•
TRACK : Repeatedly plays the selected
•
file.
3. The first file of the first directory plays
automatically.
DIR (DIRECTORY) : Repeatedly plays all
files in the selected folder.
•
4. To stop playing
Press the
button to stop playing.
5
ALL : Repeatedly plays all files.
•
NOTES
RANDOM : Plays files in random order.
|
|
•
To remove the USB device
✎
NOTES
|
|
If you press the
remove the USB device safely.
button again, you can
-
5
If the file selected to be played is located in
a folder, all the files within that folder are
played in random order. If the file selected
is located in the root folder, all files will be
played in random order.
✎
IMPORTANT
|
|
Do not connect a USB recharger to the USB
port of this product. You can damage the
product.
✎
15
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 15
2014-05-23 오후 2:43:08
Functions
To Use High Speed Search
Read Before Connecting USB Storage
Devices
You can search a desired section quickly while
the product is playing.
Some USB devices may not work properly
•
Press the
,
button.
3 4
with this product.
Each time you press the button, you move
through the section forward/backward
quickly.
•
This product only supports external HDD`s
that are formatted in the FAT file system.
USB 2.0 HDDs should be connected to a
separate power source. Otherwise, the USB
2.0 HDDs will not work.
If multiple USB external storage are
connected together, only the MP3 files in
the first HDD will be played.
Files with Digital Rights Management
(DRM) are not supported. DRM restricts
unauthorized access to a DRM file so that
file is protected from piracy.
•
•
IMPORTANT
|
|
The product does not output sound during
a high speed search.
✎
•
•
You can also press and hold the
or
✎
1
2
button on the main unit to automatically
scan for a track.
To Delete a File
Even if a file has an .mp3 extension, the file
cannot be played if it is formatted in MPEG
layer 1 or 2.
•
You can delete a file from your USB device.
1. Select a file you want to delete.
2. Press the DELETE button on the remote
Do not use an unrecognized USB hub.
Only the first 15 characters of an audio file
name are shown on the product's display.
•
•
control. "DELETE NO" is displayed.
3. Press the DELETE button on the remote
control and “DELETE YES” is displayed.
Only removable HDDs with less than 160GB
are supported. Depending on the device, a
160GB- or more removable HDD may not be
supported.
•
4. Press the
button. “DELETE END”
¬
appears and deletion is completed.
It can take several minutes for the product to
recognize the files on some USB devices.
Some USB devices (USB HDDs, in particular)
may cause a delay when moving from track
to track.
•
•
To Move to the Next/Previous Folder
Press the TUNING/ALBUM
/
button on
,
.
the remote control to move to the previous/
next folder.
With USB storage devices supporting
USB VER1.1 only, the product may access
files slowly or may not recognize the file
properties.
The maximum electrical current provided by
each USB port to connected USB devices is
0.5A (based on DC 5V).
If there is no USB connection or STOP mode
lasts for more than 25 minutes, the product
will automatically turn off.
Some USB devices, digital cameras, USB card
readers, iPods, iPhones, and Smart Phones
may not be supported.
NOTES
•
|
|
When sound files are stored in the root
directory rather than in a folder, press the
✎
TUNING/ALBUM
first TRACK.
/
button to go to the
,
.
•
•
•
To safely remove a USB device
1. Press the
button twice while the USB is
5
playing or press the
play has stopped.
button once when
5
2. When the REMOVE message appears on
the display, remove the USB device.
16
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 16
2014-05-23 오후 2:43:08
If you eject the disc, CD programming is
cancelled.
If you turn off the product, CD/USB
programming is cancelled.
•
Searching for a Track Quickly
You can select a track directly without the
,
1
button.
2
CDDA/MP3-CD/USB
NOTES
|
|
CD/USB program play will continue if you
try to switch to another mode.
✎
1. Press the SEARCH button.
After pressing the SEARCH button, turn
the VOLUME/SEARCH JOG control on
the product to the left or right to select a
desired track.
USB REC, DELETE and TUNING/ALBUM
buttons will not work in Program mode. If
you press such buttons in Program mode,
“PROGRAM PLAY” will be displayed instead.
✎
✎
You can move to the selected track
directly.
•
If a file in the program to be played was not
in a supported format, playback skips to the
next file automatically.
2. When searching is done, the track will
automatically start playing.
Viewing or Editing Programmed Tracks
Using the Program Function
You can view and edit a list of programmed
tracks.
This function is not available during playback
of an MP3-CD/USB.
1. If a programmed track is being played,
You can program the playback order of up
to 99 tracks of your choice.
•
press the
button once.
5
2. Press the PROGRAM button twice to
However, you must stop playing the CD/USB
before selecting tracks.
•
display the message below:
1. While in CD/USB playback mode, press the
SAVED 01 TRACK002
(01= program number, 002= track number)
button to stop playing the CD/USB.
5
2. Press the PROGRAM button to display the
3. Repeatedly press the
button until the
¬
message below:
desired track is displayed.
PROG 01 TRACK---
(01= program number, ---= track number)
4. Press the or button to select a
1
2
different track.
5. Press the
button to confirm your
¬
3. Use the
or
button or the VOLUME/
1
2
selection.
SEARCH JOG to move to a desired track.
6. To play the programmed tracks, press the
Press
Press
to move to the previous track.
to move to the next track.
•
•
1
2
button.
To repeat
4. Press the
button to confirm your
¬
selection. The selection is stored and
is displayed.
1. Press the REPEAT button.
Each time you press this button, the mode
changes as follows:
5. To select another track, follow Steps 3 and
4 above.
OFF TRACK ALL
;
;
6. Press the
button to play the
programmed tracks.
7. Press the
button to stop playing the
5
programmed tracks, Press the
button
5
again to cancel playing the programmed
tracks.
17
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 17
2014-05-23 오후 2:43:08
Functions
To connect the Hi-Fi Component to a
Bluetooth device
Bluetooth
You can use a Bluetooth device to enjoy music
with high quality stereo sound, all without
wires!
Before you begin, confirm that your Bluetooth
device supports the Bluetooth-compliant
stereo headset function.
What is Bluetooth?
1. Press the CD/Bluetooth button of the Hi-
Fi Component to display the BLUETOOTH
message.
Bluetooth is a technology that enables
Bluetooth compliant devices to interconnect
easily with each other using a short, wireless
connection.
A Bluetooth device may cause noise or
malfunction, depending on usage, when:
You will see WAIT for a short period
of time and then READY on the front
display of the Hi-Fi Component.
•
•
2. Select the Bluetooth menu on the
Bluetooth device you want to connect.
(Refer to the Bluetooth device's user
manual.)
A part of your body is in contact with
the receiving/transmitting system of the
Bluetooth device or the Hi-Fi Component.
-
It is subject to electrical variation from
obstructions caused by a wall, corner, or
office partitioning.
-
3. Select the Stereo headset menu on the
Bluetooth device.
You will see a list of scanned devices.
•
It is exposed to electrical interference from
-
4. Select "[Samsung] HI-FI XXXXXX" from
same frequency-band devices including
medical equipment, microwave ovens, and
wireless LANs.
the list.
When the product is connected to
the Bluetooth device, it will display
•
Pair the Hi-Fi Component with the Bluetooth
device while they are close together.
•
CONNECTED
BLUETOOTH on the
;
front display.
The greater the distance between the Hi-Fi
•
Component and the Bluetooth device, the
worse the quality. If the distance exceeds the
Bluetooth operational range, the connection
is lost.
In poor reception areas, the Bluetooth
connection may not work properly.
If the Bluetooth device has failed to pair
with the product, delete the previous
“[Samsung] HI-FI XXXXXX” found by the
Bluetooth device and have it search for
the product again.
•
•
5. You can listen to the music playing on the
connected Bluetooth device over the Hi-Fi
Component system.
The Bluetooth connection only works
•
when the Bluetooth device and the Hi-
Fi Component are close together. The
connection will be automatically cut off
if the Bluetooth device is out of range.
Even within range, the sound quality may
be degraded by obstacles such as walls or
doors.
In Bluetooth mode, some model's
Play/Stop/Next/Back functions are not
available.
•
NOTES
|
|
The product only supports Middle Quality
SBC data (up to 237kbps@48kHz), and
does not support High Quality SBC data
This wireless device may cause electric
interference during its operation.
•
The AVRCP feature is not supported.
✎
✎
Connect only to a Bluetooth device that
supports the A2DP (AV) function.
You cannot connect to a Bluetooth device
that supports only the HF (Hands Free)
function.
✎
18
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 18
2014-05-23 오후 2:43:08
Only one Bluetooth device can be paired at
a time.
In Bluetooth connection mode, the
Bluetooth connection will be lost if the
distance between the Hi-Fi Component and
the Bluetooth device exceeds 16.25 feet (5
meters).
✎
✎
✎
✎
Once you have turned off the Hi-Fi
Component and the pairing is disconnected,
the pairing will not be restored
automatically. To reconnect, you must pair
the device again.
If the Bluetooth device comes back into the
effective range after disconnecting, you can
restart the Hi-Fi Component to restore the
pairing with the Bluetooth device.
The Hi-Fi Component system may not
search or connect properly in the following
cases:
✎
The Hi-Fi Component automatically turns
off after 25 minutes in the Ready mode.
✎
✎
If there is a strong electrical field around
the Hi-Fi Component.
-
When a Bluetooth device is connected
to the Hi-Fi Component system, the Hi-Fi
Component System automatically switches
to the Bluetooth mode if it is in a different
mode.
If several Bluetooth devices are
simultaneously paired with Hi-Fi
Component.
-
If the Bluetooth device is turned off, not
in place, or malfunctions.
-
Using Bluetooth Power On
Note that such devices as microwave
ovens, wireless LAN adaptors, fluorescent
lights, and gas stoves use the same
-
When the product is turned off, you can
connect your smart device to the product via a
Bluetooth connection to turn it on.
frequency range as the Bluetooth device,
which can cause electric interference.
1. Press and hold the Bluetooth button on
the remote to set the Bluetooth Power On
function On. Bluetooth Power On appears
on the display.
To disconnect the Bluetooth device
from the Hi-Fi Component
2. When the product is off, connect
your smart device to the product via
Bluetooth. (For information on Bluetooth
connections, refer to your smart device’s
manual.)
You can disconnect the Bluetooth device from
the Hi-Fi Component. For instructions, see the
Bluetooth device's user manual.
The Hi-Fi Component will be disconnected.
When the Hi-Fi Component is disconnected
from the Bluetooth device, the Hi-Fi
•
•
3. When the connection is complete, the
product turns itself on automatically in
Bluetooth mode.
Component displays DISCONNECTED
;
READY on its display.
Select the desired music to play from
your smart device.
•
To disconnect the Hi-Fi Component
from the Bluetooth device
NOTES
|
|
Press another mode button on the front
panel of the Hi-Fi Component to switch from
Bluetooth mode to another mode or turn off
the Hi-Fi Component. The currently connected
device is disconnected.
Press and hold the Bluetooth button on the
remote control to turn the Bluetooth Power
On function on or off.
✎
Each time you press and hold this button,
the Hi-Fi Component displays Bluetooth
Power On Off on its display.
;
NOTES
|
|
The connected Bluetooth device will wait a
certain amount of time for a response from
the Hi-Fi Component before terminating the
connection. (Disconnection time may differ,
depending on the Bluetooth device)
✎
19
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 19
2014-05-23 오후 2:43:08
Functions
To disconnect the TV from the Hi-Fi
Component
TV SoundConnect
You can listen to the sound from your
SoundConnect Compatible Samsung TV
through the Hi-Fi Component by using the TV
SoundConnect function.
You can disconnect the TV from the Hi- Fi
Component.
For instructions, see the TV's user manual.
When the Hi-Fi Component is disconnected
from the TV, the Hi-Fi Component displays
•
To connect the Hi-Fi Component to a
SoundConnect Compatible Samsung
TV
DISCONNECTED REQUEST on its display.
;
To disconnect the Hi-Fi Component
from the TV
Before activating this function, be sure to
set the Samsung TV's SoundConnect or
SoundShare function to On.
Press another mode button on the front panel
of the Hi-Fi Component to switch from TV
SoundConnect mode to another mode or
turn off the Hi-Fi Component. The currently
connected device is disconnected.
1. Press the TV SoundConnect button of
the Hi-Fi Component to display the TV
SOUNDCONNECT message.
WAIT SEARCH REQUEST
;
;
NOTES
|
|
2. Set Add New Device to On in the TV's
SoundConnect Settings menu. (Refer to
the TV's user manual for details.)
The connected TV will wait a certain
amount of time for a response from the
Hi-Fi Component before terminating the
connection.(Disconnection time may differ,
depending on the TV)
✎
3. When the Hi-Fi Component is connected
to the TV, it will display [TV] Name
CONNECTED on the front display.
;
The connection may be lost or sound may
stutter if the distance between the TV and
the Hi-Fi Component exceeds 6.5 feet (2 m).
✎
✎
✎
4. The audio from the connected TV plays
over the Hi-Fi Component system.
NOTES
|
|
Instability in the network environment may
cause the connection to be lost or sound to
stutter.
The SoundConnect feature is available on
some Samsung TVs released since 2012.
Check whether your TV supports the
SoundShare or SoundConnect function.
(For further details, refer to the TV's user's
manual.)
✎
The Hi-Fi Component automatically turns
off after 25 minutes if it is not connected to
a TV.
Using My Karaoke
If you unplug the Hi-Fi Component, the TV
SoundConnect connection is terminated. To
re-establish the connection, plug the Hi-Fi
Component into an outlet, and then set the
TV SoundConnect connection again.
✎
You can use the MY Karaoke function to sing
along with your favorite CDs and USB tracks.
1. Connect the microphone to the MIC jack
Only one Hi-Fi Component can be
connected to a TV via TV SoundConnect at
at time.
✎
✎
on the front of the product.
If your microphone plug is smaller
•
than the 6.3 mm MIC jack, you need a
Connector-Adaptor (not supplied) to
complete the connection.
To connect to another TV in TV
SoundConnect mode, press the
button
for more than 5 seconds, and then connect
to the other TV by following the directions
above.
First, connect the Connector-Adaptor
to the MIC jack on the front of the
product,
-
Second, connect the microphone (with
larger jack) to the Connector-Adaptor.
-
20
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 20
2014-05-23 오후 2:43:08
2. Press the MIC VOL-, + button on the
remote control to adjust the volume of
the microphone.
If Program Play has been set in CD/USB
mode, the settings change as follows:
•
AUTO CHANGE OFF AUTO CHANGE
;
ALL AUTO CHANGE PROGRAM
;
3. Press the MY KARAOKE button on the
remote control to suppress the vocal if you
need to. Each time you press the button,
the selection changes as follows:
When the AUTO CHANGE mode is
-
"ALL", the Hi-Fi Component plays
supported music from DISC, USB1,
and USB2 continuously.
MY KARAOKE ON MY KARAOKE OFF
;
When the auto change mode is
-
If you hear strange noises (squealing
•
"PROGRAM", the Hi-Fi Component
plays programmed music from
a disc in the disc slot, then plays
programmed files on a USB device
connected to USB1, and then plays
programmed files on a USB device
connected to USB2. The files are
played continuously. See Using the
Program Function on page 15.
or howling) while using the Karaoke
feature, move the microphone away
from the speakers. Turning down the
microphone's volume or the speaker
volume is also effective. Do not aim the
MICROPHONE towards the SPEAKERS.
The microphone does not operate in the
AUX and TUNER mode.
•
If you press the POWER button,
If you connect a microphone, GIGA
SOUND automatically turns off. To turn
Giga Sound back on, you must remove
the microphone, and then press the
GIGA SOUND BEAT button.
-
•
another function button, or the EJECT
button, the AUTO CHANGE function
automatically switches to "OFF" mode.
When the Auto Change mode is "ALL
or PROGRAM", the main unit cannot
-
When My Karaoke is on, GIGA SOUND
does not work.
•
•
•
record.
When the Auto Change mode is "ALL
or PROGRAM", the REPEAT function
automatically switches to OFF.
When the Auto Change mode is "ALL"
or "PROGRAM", the REC SPEED and
USB REC functions do not work.
When the DISC play ends, if there's
no device connected to USB1 and/or
USB2, the unit will continue to play
the disc.
-
When you turn My Karaoke off, all My
Karaoke settings are lost.
My Karaoke is only available when a
microphone is connected to the Hi-Fi
Component.
-
My Karaoke does not operate in the
Bluetooth, TV SoundConnect, FM, or
AUX mode.
•
-
When USB play ends, if there's no disc
in the unit, the unit will continue to
play music from USB1 and/or USB2.
-
Auto Change Function
You can play a disc followed by a USB device
connected to USB1 and/or USB2 continuously.
When USB is playing, if you
-
disconnected the USB, the AUTO
CHANGE function automatically
switches to "OFF" mode.
If there is no device connected to
USB1, the unit jumps to USB2.
1. Press the AUTO CHANGE button to select
a mode, and then press
selection.
to apply your
¬
-
If Program Play has not been set in
CD/USB mode, the settings change as
•
follows: AUTO CHANGE OFF AUTO
;
CHANGE ALL
21
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 21
2014-05-23 오후 2:43:08
Functions
Listening to the Radio
Timer Function
To Store the Stations You Want
Setting the Clock
You can store up to:
15 FM stations.
For each step, you have a few seconds to set
the required options. If you exceed this time,
you must start again.
1. Select FM by pressing the TUNER/AUX
1. Press the TIMER SET button on the remote
button.
control twice. "CLOCK SET" is displayed.
2. To search for a station, press the TUNING
2. Press the
button on the remote
¬
MODE button on the remote control or
control. The hour flashes.
the button on the product one or more
@
times until MANUAL is displayed.
To increase the hours: TUNING/ALBUM
•
,
.
3. Find a station by:
To decrease the hours: TUNING/ALBUM
•
Pressing and holding the TUNING/
•
3. When the correct hour is displayed, press
ALBUM
or
button on the remote
,
.
the
button, and then the minutes
¬
control to automatically search for
broadcasting stations.
flash.
To increase the minutes: TUNING/ALBUM
•
•
,
.
4. Press the MO/ST button to switch
To decrease the minutes: TUNING/ALBUM
between stereo and mono.
4. When the correct minute is displayed,
In a poor reception area, select MONO
for a clear, interference-free broadcast.
•
press the
button. "TIMER PLAY SET"
¬
appears in the display.
This applies only when listening to an
FM station.
•
Setting the Timer
5. If you do not want to store the radio
station found, go back to Step 3 and
search for another station.
The timer enables you to set the product to
switch on or off at specific times automatically.
Before setting the timer, check that the
current time is correct.
•
Otherwise:
For each step, you have a few seconds to set
the required options. If you exceed this time,
you must start again.
•
a. Press the
button.
¬
b. Or, press the TUNING/ALBUM button
on the remote control to select a
If you no longer want the product to be
•
program number in the PRESET mode.
switched on or off automatically, you must
cancel the timer by pressing the TIMER
ON/OFF button.
c. Press the
button to save the preset.
¬
6. To store other radio frequencies, repeat
Steps 3 to 5.
Example: You want to wake up to
music every morning.
Selecting a Stored Station
To listen to a stored station, follow these steps:
1. Press the TIMER SET button until TIMER
PLAY SET is displayed.
1. Select FM by pressing the TUNER/AUX
2. Press the
button.
button on the product or remote control.
¬
Result: ON TIME is displayed for a few
seconds. You can set the timer switch-on
time.
2. Press the TUNING MODE button on the
remote control until “PRESET” is displayed.
3. Press the
,
buttons on the main unit
1 2
or the TUNING/ALBUM
,
buttons
, .
on the remote control to select a preset
number.
22
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 22
2014-05-23 오후 2:43:08
3. Set the timer switch-on time.
7. Press the
button.
¬
Result: TIMER REC SET (Do you want to
record?) is displayed.
a. Press the TUNING/ALBUM
or
or
,
,
.
.
button to set the hours.
8. Press the
button.
¬
b. Press the
button.
¬
Result: REC SET YES/NO is displayed. You
can press the TUNING/ALBUM or
Result: The minutes flash.
,
.
c. Press the TUNING/ALBUM
button to select REC YES or REC NO, and
button to set the minutes.
then press button.
¬
d. Press the
button.
¬
1) If you select REC NO, it will cancel
tuner timer recording and any currently
set tuner timer recording. Note that
selecting REC NO does not cancel the
Timer setting.
Result: OFF TIME is displayed for a few
seconds. You can now set the timer
switch-off time.
4. Set the timer switch-off time.
a. Press the TUNING/ALBUM
or
,
.
2) If you select REC YES, you can set the
button to set the hours.
tuner timer recording on and off times.
b. Press the
button.
¬
a. Press the
button.
¬
Result: The minutes flash.
Result: ON TIME is displayed for a
few seconds. You can set the tuner
timer recording switch-on time.
c. Press the TUNING/ALBUM
or
,
.
button to set the minutes.
b. Press the
button.
¬
d. Press the
button.
¬
Result: OFF TIME is displayed for a
few seconds. You can set the tuner
timer recording switch-off time.
Result: VOLUME XX is displayed, where
XX corresponds to the volume already
set.
NOTES
5. Press the TUNING/ALBUM
or
button
|
|
,
.
to adjust the volume level and press the
Tuner timer recording On/Off times can
differ from Timer On/Off times.
✎
button.
¬
Result: The source to be selected is
displayed.
If the timer switch on and off times are
identical, the word ERROR is displayed.
✎
✎
6. Press the TUNING/ALBUM
or
button
,
.
You can use the
1 2
product instead of the TUNING/ALBUM
,
buttons on the
to select the source the Hi-Fi Component
will play when it switches on.
,
or
button to make adjustments in Steps
.
3 through 8.
If you select
FM (radio)
You must also
a. Press the
If the switch-on or -off time is the same as
the timer recording time, only the switch-
on or -off time is effective, and the timer
recording is not applied.
✎
✎
button.
¬
b. Select a preset
station by pressing
the TUNING/ALBUM
When you use the auto timer, you may
need an additional step to use a CD or USB
device with it, depending on the disc (or
device). Consequently, it is easier to use the
tuner instead.
or
button.
,
.
CD (compact
disc)
Load a compact disc.
USB
Connect a USB device.
If you select CD or USB mode when there
is no disc or no USB in the product, it will
automatically change to TUNER.
✎
23
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 23
2014-05-23 오후 2:43:09
Functions
USB 1 (Recording device is on USB 2)
Cancelling the Timer
Connect the USB device with the files
you want to record to USB 1 jack.
After you have set the timer, it will start
automatically. When it starts, the TIMER ON
message appears on the display. If you no
longer want to use the timer, you must cancel
it.
•
Press the USB button to select USB 1.
•
Play a song from the USB 1.
•
To cancel the timer, Press the TIMER ON/OFF
button once.
•
External Source
Connect an External device/MP3 player
to the product.
•
To restart the timer, Press the TIMER ON/OFF
button once again.
•
Press the TUNER/AUX button to select
AUX IN 1 or AUX IN 2.
•
NOTES
|
|
When you select the TIMER OFF mode, the
TIMER RECORDING and TIME function are
not available.
✎
Play a song from the external device.
•
3. Press the USB REC button on the remote
control to start recording.
CD
The Recording Function
CD recording starts and “TRACK
RECORD” and the current track number
appear on the display alternately.
•
Basic Recording
You can record from a CD, a USB device, a
radio broadcast, or an external source to a USB
storage device.
If you want to record all the tracks on
the disc, press and hold the USB REC
button. "FULL CD RECORD" is displayed.
•
1. Connect an external USB storage device to
RADIO
a USB (
) jack on your product. You
can use USB 2.
“TUNER RECORD” is displayed and
recording starts.
•
2. Play a disc or USB, turn on the radio and
select a station, or connect an external
source to your product as described
below.
CD-ROM/USB
“FILE COPY” is displayed and recording
starts.
•
CD
You can also copy a folder containing
•
Press the CD button on the product to
select the CD function.
•
MP3/WMA files to a device on USB
2. Press and hold the USB REC button
while the system plays an MP3 or WMA
file located in a folder. Your system
displays "FOLDER COPY", and will record
all the files in that folder.
Insert a CD gently into the disc slot.
•
Use the CD selection (
or
) buttons
2
•
1
to select the desired song.
TUNER
When the recording is done, “STOP” is
displayed.
•
Select FM by pressing the TUNER/AUX
button.
•
•
If there is a file with the same name
on the USB 2 device, "EXIST FILE" is
displayed, and the function is canceled.
•
Select the radio frequency you want to
record.
24
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 24
2014-05-23 오후 2:43:09
If a microphone is connected to the
product and you press the USB REC
button, you activate the MP3 Recording
function, not the Copy function.
When you use the CD high speed search
function, the CD recording function is
unavailable.
•
•
✎
With some USB devices, recording time may
be longer.
✎
✎
✎
Press the USB REC button for a second
to start FILE COPY. Press and hold the
USB REC button for a few seconds to
start FOLDER COPY.
In the Program mode, you can't use the
recording function.
When the Recording function is active,
the EQ and GIGA SOUND functions
automatically turn off and are unavailable.
External Source
“AUX RECORD” is displayed and
recording starts.
•
During a CD recording, the REPEAT function
automatically turns off and is unavailable.
✎
✎
If you use the MIC function during a CD
recording, the voice from the microphone
will be recorded.
CD/USB1(MP3) & MIC
“MP3 RECORD” is displayed and
recording starts.
•
You can not record audio from the radio
when searching for a station or if there are
no frequencies available when the product
is set to Tuner mode.
✎
✎
4. To stop recording, press the
button.
5
The recording is automatically saved as an
MP3 file.
5. After the recording is finished, a
directory named “RECORDING”(CD-
DA), “COPY”(CD-ROM/ USB), “TUNER
RECORDING”, “AUX RECORDING” or “MP3
RECORDING” is created in your device.
Note that setting the input level too loud
when recording music from an external
device through the AUX or USB channel
may introduce noise into the recording.
If this occurs, lower the external device’s
volume level.
NOTES
|
|
WMA/MP2 files can only be copied not
recorded.
✎
Recording Speed
Each time you press the REC SPEED button on
the remote control, the recording speed will
change as follows:
Do not disconnect the USB device or the AC
Cord during recording. You can cause file
damage.
✎
✎
RECORD SPEED x 1 RECORD SPEED x 4
;
If you disconnected the USB device during
recording, the product will turn off and you
will not be able to delete the file that has
been recorded. If this occurs, connect the
USB device to a PC, back up the USB data to
the PC, and then reformat the USB device.
When you record from the tuner or an
external source, you cannot change the
recording speed.
•
If you select RECORD SPEED X 4, sound is
not produced during the recording.
If you connect a microphone, you have one
recording speed mode available: RECORD
SPEED X 1.
•
•
If the USB device does not have enough
memory, “NOT ENOUGH MEMORY” will
appear on the display.
✎
✎
During recording, if you disconnect the
microphone, the recording will stop. If you
reconnect the microphone, the recording
will not restart.
•
The Recording function supports the FAT
file systems only. The NTFS file system is not
supported.
NOTES
|
|
Even when RECORD SPEED x4 is set,
recording may not be made in x4 speed
depending on the used USB storage device.
✎
25
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 25
2014-05-23 오후 2:43:09
Functions
NOTES
|
|
Special Sound Effects
When the Hi-Fi Component is recording,
the EQ function is turned off automatically
and is unavailable.
✎
Selecting EQ Mode
Your Hi-Fi Component system provides
If no buttons are pressed within 8 seconds,
your settings will automatically be cancelled
and the previous settings will be saved.
✎
predefined equalizer settings that are optimized
for particular music genre. You can also adjust
the bass, middle, and treble levels manually.
The EQ mode may be different depending
on your region.
✎
✎
1. Press the EQ button.
Each time you press the EQ button or turn
the VOLUME/SEARCH JOG control on the
product, the mode changes as follows:
Use the VOLUME/SEARCH JOG to alter the
EQ mode, and the selected EQ mode will be
applied after 2 seconds.
OFF FLAT RANCHERA CUMBIA
;
;
;
;
Use the VOLUME/SEARCH JOG to alter
✎
REGGAE MERENGUE SALSA
;
;
;
the EQ mode, and then press
screen disappears.
. The EQ
¬
REGGATON FOLKLORE PARTY POP
;
;
;
HIP-HOP ROCK JAZZ CLASSIC
;
;
;
;
;
ELEC-TRONIC MP3 ENHANCER VIRTUAL
;
;
FOOTBALL MODE function
SOUND USER EQ
;
The football mode brings greater realism to
sports broadcasts.
2. To set the BASS, MID (Middle), and TREB
(Treble) levels manually, select USER EQ,
and then press the
button.
1. Press the FOOTBALL MODE button on the
product.
¬
Result: The BASS level (left numeric)
flashes.
Each time you press this button, the mode
changes as follows:
Press the
or
button on the product
1
2
or TUNING/ALBUM
,
button to select
, .
a level from -06 to 06.
Then, press the button.
OFF ANNOUNCER STADIUM
;
;
2. To cancel this function, press the
FOOTBALL MODE button until “OFF” is
displayed.
¬
Result: The MIDDLE level (middle numeric)
flashes.
GOAL Function
Press the
or
button on the product
1
2
or TUNING/ALBUM
,
button to select
, .
a level from -06 to 06.
Then, press the button.
Press this button to add the sound of cheering
while watching a football game.
¬
1. Press the GOAL button on the remote
control.
Result: The TREBLE level (right numeric)
flashes.
Each time you press this button, the mode
changes as follows:
Press the
or
button on the product
1
2
or TUNING/ALBUM
,
button to select
, .
a level from -06 to 06.
Then, press the button.
GOAL ON GOAL OFF
;
¬
2. To cancel this function, press the GOAL
button until “GOAL OFF” is displayed.
Result: Setting is complete.
26
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 26
2014-05-23 오후 2:43:09
NOTES
|
|
DJ BEAT Function
Press the GOAL button to output the
currently playing sound file mixed with the
GOAL sound.
✎
The DJ Beat function lets you turn on the DJ
Beat sound effect functions. The level of each
effect is adjustable.
Press the DJ BEAT button on the remote
control or on the product.
Each time you press this button, the mode
changes as follows:
GIGA SOUND Function
The GIGA SOUND function amplifies the
bass sound and provides twice the bass for
powerful, realistic sound.
IMPORTANT
|
|
1. Press the GIGA SOUND BEAT button on
the main unit or the GIGA button on the
remote control. Each time you press this
button, the mode changes as follows:
You can set each of the DJ Beat functions
from -15 to +15. The initial setting for all
functions is 0.
✎
FLANGER : Creates an effect similar to the
sound of a jet engine revving up and down.
CHORUS : Creates an effect similar to a
singing chorus.
•
•
GIGA SOUND BEAT GIGA SOUND OFF
;
2. To cancel this function, press the GIGA
SOUND BEAT button until “GIGA SOUND
OFF” is displayed.
WAHWAH : Creates a 'Wah~ Wah~' effect.
TREMOLO : Repeatedly and rapidly turns the
volume up and down.
•
•
NOTES
|
|
The GIGA SOUND mode may be different
depending on your region.
✎
FUZZ : Distorts the original sound to make it
harder and harsher.
PHASER : Alters the original sound from
clear to dull.
SLAPBACK : Creates the effect of a slapback
echo following the original sound.
DJ BEAT OFF : Turns off this function.
•
•
•
•
BEAT WAVING Function
The Beat Waving function lets you change the
Speaker LED display mode.
1. Press the BEAT WAVING button on the
product or on the remote control.
Each time you press this button, the mode
changes as follows:
NOTES
|
|
The red LED turns on around the button you
✎
pushed and around the DJ BEAT button.
STARDUST EMERALD MOON SOLAR
;
;
BOMB SHOOTING STAR STAR
;
;
;
You can control the intensity of the effect
with the Volume Jog. To control the volume,
press the product's VOLUME/DJ button.
✎
PARTY 1 PARTY 2 FUN 1 FUN 2 PURE
;
;
;
;
FRESH LOVE JOY SUNSET SUNRISE
;
;
;
;
;
;
NATURE 1 NATURE 2 WAVE 1 WAVE
;
;
;
To cancel an effect, press the effect's button
again.
✎
✎
✎
2
AURORA OFF
;
;
NOTES
|
|
You can also control the effect using the
EFFECT LEVEL button on the remote control.
If you select BEAT WAVING OFF, all the
✎
speaker LED displays are turned off.
Use the Volume Jog to control the intensity
of the effect that was activated last. For
example, if you activated the WahWah
effect and then the Panning effect, the
Volume Jog will control the Panning effect.
To control the intensity of the effect you
applied first, press the button of effect that
you applied last to turn it off. Then, you can
use the Volume Jog to control the intensity
of the first effect.
✎
27
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 27
2014-05-23 오후 2:43:09
Functions
NOTES
|
|
+PANNING Funcion
When the DANCE TIME sound file finishes
playing, the DANCE TIME mode changes to
DANCE TIME OFF.
✎
Increases the left and right speaker's output
in turn and makes it seem as if the sound is
moving from side to side.
When DANCE TIME mode is switched ON,
the B/T, TV SoundConnect, TUNER, and
AUX sources enter Mute mode. The music
that is currently playing is paused.
✎
✎
NOTES
|
|
To apply the PANNING effect to another
effect, press the +PANNING button when
the other effect is active or press another
effect button when the PANNING effect is
active.
✎
When you turn off DANCE TIME, any CD
or USB whose playback had been paused
when you started DANCE TIME resumes
from the beginning of the track that had
been playing.
NON-STOP MUSIC RELAY Function
The NON-STOP MUSIC RELAY function
When playing a DANCE TIME sound file,
you can change the dance music by pressing
✎
plays music continuously without an interval
between tracks/files. If there were two mp3
files, it skips to the next file’s 10 seconds from
the start position when the previous track
reaches its 10 seconds before the end position.
Press the NON-STOP MUSIC RELAY button on
the product or NON-STOP RELAY button on
the remote control.
the
,
button.
1 2
TEMPO Function
Use this to change the TEMPO while music is
playing.
1. During playback (CDDA/ MP3/ WMA),
press the TEMPO button on the remote
control.
Each time you press this button, the mode
changes as follows:
2. Select the desired TEMPO by using the
EFFECT LEVEL button on the remote
control.
NON-STOP RELAY ON NON-STOP RELAY
;
OFF
NOTES
|
|
NOTES
|
|
This function is only available during
playback of a CD/USB.
✎
TEMPO Function does not operate in the
Bluetooth, TV SoundConnect, FM and AUX
mode.
✎
DANCE TIME Function
When you turn TEMPO off, all TEMPO
settings are lost.
✎
Press the DANCE TIME button on the remote
control when playing music to play the dance
music stored in the product.
Use this function to enjoy exciting music.
1. Press the DANCE TIME button on the
remote control.
Each time you press this button, the mode
changes as follows:
DANCE TIME ON DANCE TIME OFF
;
2. To cancel this function, press the DANCE
TIME button until "DANCE TIME OFF" is
displayed.
28
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 28
2014-05-23 오후 2:43:09
Appendix
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instructions below do not help, turn off the product,
disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics
Service Center.
Symptom
Check/Remedy
I cannot eject the disc.
Is the power cord plugged securely into the outlet?
Turn off the power and then turn it back on.
•
•
Playback does not start
immediately when the Play/Pause
button is pressed.
Are you using a deformed disc or a disc with scratches on
the surface?
Wipe the disc clean.
•
•
•
Sound is not produced.
No sound is heard during fast playback, slow playback,
and step motion playback.
Are the speakers connected properly? Is the speaker setup
correctly customized?
•
Is the disc severely damaged?
•
•
The remote control does not work.
Is the remote control being operated within its
operational angle and distance range?
Are the batteries drained?
•
•
The product is not working.
Press the button (on front panel) for more than 5
@
(Example: The power goes out
or the front panel buttons don't
work, or you hear a strange noise.)
seconds with no disc inside. The initialization message
appears on the screen, and the power will turn off
automatically. When you turn your product on again, all
the settings will be reset.
The product is not working
normally.
Don't use this unless absolutely necessary.
Can't receive radio broadcast.
Is the antenna connected properly?
If the antenna's input signal is weak, install an external
FM antenna in an area with good reception.
•
•
29
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 29
2014-05-23 오후 2:43:10
Appendix
Specifications
Power Requirements
Power Consumption
AC110-120V ~ 50/60Hz
137W
Main unit
79.6 lbs
Weight
Speaker
Main unit
Speaker
67.0 lbs
General
23.9 (W) x 33.5 (H) x 19.3 (D) inches
23.9 (W) x 27.8 (H) x 19.3 (D) inches
Dimensions
Operating Temperature
Range
41°F~95°F (5°C~35°C)
Operating Humidity Range
Signal/Noise ratio
10 % to 75 %
55 dB
FM Tuner
CD Disc
Usable sensitivity
10 dB
Total harmonic distortion
1 %
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
625W/CH(4Ω)
CD : 12 cm (COMPACT
DISC)
Front speaker output
Subwoofer output
Frequency range
S/N Ratio
625W/CH(4Ω)
22Hz~20KHz
Amplifier
65 dB
Channel separation
Input sensitivity
60 dB
AUX IN1 1.2V, AUX IN2 2.0V
*: Nominal specification
Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
Weight and dimensions are approximate.
Design and specifications are subject to change without prior notice.
For information on the power supply and power consumption, refer to the label attached to the
product.
-
-
-
-
Dispose unwanted electronics through an approved recycler.
call, (877)278 - 0799
-
Open Source Announcement
To send inquiries and requests regarding open sources, contact Samsung via Email
30
English
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 30
2014-05-23 오후 2:43:10
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG)
and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against
manufacturing defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the
United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service
procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill
of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center.
Transportation of the product to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced
parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and
products assume the remaining original warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name
are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided,
are on an “AS IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except
to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply
to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications
and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish;
accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities,
services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied and
authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage,
fluctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and
environmental instructions that are covered and prescribed in the instruction book; product removal or reinstallation;
reception problems and distortion related to noise, echo, interference or other signal transmission and delivery problems.
SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR
INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG.
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG customer care center.
The benefits of this Limited Warranty extend only to the original purchaser of Samsung products from an authorized
Samsung reseller. THIS LIMITED WARRANTY SHALL NOT APPLY TO ANY SAMSUNG PRODUCTS PURCHASED FROM
UNAUTHORIZED RESELLERS OR RETAILERS, EXCEPT IN STATES WHERE SUCH RESTRICTION MAY BE PROHIBITED. For a
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 31
2014-05-23 오후 2:43:10
QUESTIONS OR COMMENTS?
Area
CALL
OR VISIT US ONLINE AT
WRITE
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park,
NJ 07660
1-800-SAMSUNG
(726-7864)
support
IN THE US
© 2014 Samsung Electronics Co., Ltd. All rights reserved.
AH68-02706A-03
AH68-02706A-03
Download from Www.Somanuals.com. All Manuals Search And Download.
[MX-HS8500-ZA]AH68-02706A-03ENG.indd 32
2014-05-23 오후 2:43:11
|