HW-C500
HW-C560S
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
HW-C500-C560S-XAA_0609.indd 1
2010-006-09
5:10:52
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment.
This equipment should be installed and operated with minimum distance 7.9 inches between the radiator and your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Wireless Internet Radio) does not exceed the Class B limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep
these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these Instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachment/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
3
HW-C500-C560S-XAA_0609.indd 3
2010-006-09
5:10:56
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
PRECAUTIONS
2.7 inches
SETUP
INPUT SELECT
ENTER
TONE CONTROL
3.9 inches
SOUND EFFECT
AUDIO
ASSIGN
MULTI CH
INPUT
A
V
TUNING
MODE
ASC MIC
ASC
S. DIRECT
SELECT
MEMORY
SYNC
3.9 inches
3.9 inches
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure
the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely
from the power supply, remove the AC plug from the wall outlet, especially when left unused for a long period of time.
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SETUP
SOUND EFFEC
T
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFEC
T
AUDIO
ASSIGN
MULTI CH
INPUT
A
V
TUNING
MODE
A
S
C
M
I
C
ASC
S
.
D
I
R
E
C
T
SELECT
MEMORY
SYNC
AUDIO
ASSIGN
MULTI CH
INPUT
A
V
TUNIN
MODE
A
S
C
M
I
C
ASC
S
.
D
I
R
E
C
T
SELECT
MEMORY
SYNC
During thunderstorms, disconnect the AC plug from the
wall outlet.
Do not expose the unit to direct sunlight or other heat
sources.
Voltage peaks due to lightning could damage the unit.
This could lead to overheating and malfunction of
the unit.
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFEC
T
AUDIO
ASSIGN
MULTI CH
INPUT
A
V
TUNING
MODE
A
S
C
M
I
C
ASC
S
.
D
I
R
E
C
T
SELECT
MEMORY
SYNC
Phones
Protect the player from moisture(i.e.vases), and excess
heat(e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...). Disconnect the power
cable from the AC supply if the player malfunctions. Your
player is not intended for industrial use.
The batteries used with this product contain
chemicals that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
4
HW-C500-C560S-XAA_0609.indd 4
2010-006-09
5:10:56
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Digital AV Receiver
iPod
This product is a pure digital AV receiver that performs
digital signal processing to minimize signal distortion and
loss.
You can enjoy music files by connecting your iPod/iPhone
to the AV Receiver with the supplied iPod dock.
SFE (Sound Field Effect) Using
32bit Audio Digital Signal
Processing
Provides more realistic surround sound with normal
stereo audio sources.
Dolby Pro Logic II
DPL II processes any high quality stereo signal source
into five separate full frequency channels.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to
24 bit/96kHz and applies it to a 5.1 CH sound track.
Anynet+ (HDMI-CEC) Function
Anynet+ is a function that can be used to operate this
AV Receiver with a Samsung TV remote control, by
connecting the receiver to a SAMSUNG TV using an
HDMI Cable. (This function is available only in
connection with Samsung TV and DVD player
supporting Anynet+(HDMI-CEC).)
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for
both music and movie contents and uses less
compression than Dolby Digital for richer sound.
ACCESSORIES
INPUT SELECT
POWER
TV SOURCE
AMP/TV
DIMMER
BD/DVD
1
4
2
3
6
5
SLEEP
7
8
9
DSP
PROLOGIC
AUDIO ASSIGN
0
MUTE
TUNING
/CH
VOL
ASC
TUNER MEMORY
SETUP/MENU
SUBWOOFER
MO/ST
INFO
RETURN
EXIT
BD/DVD
SAT
TV
CD
MULTI CH
AUX
iPod
Remote Control
(AH59-02305A)/
Batteries (AAA size)
(4301-000116)
FM antenna
(AH42-00017A)
User’s manual
(AH68-02266R)
iPod Dock
(AH96-00051A)
ASC microphone
( AH30-00099A )
5
HW-C500-C560S-XAA_0609.indd 5
2010-006-09
5:11:00
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2
3
4
Safety Warnings
Important Safety Instructions
Precautions
SAFETY INFORMATION
2
5
Accessories
FEATU5RES
DESCRIPTION
8
8
Front Panel
10 Rear Panel
12 Display
13 Insert Remote Control Batteries
13 Operation Range of the Remote Control
14 Tour of the Remote Control
16 Speaker Positioning
18 Connecting the Speakers
CONNECTIONS
20 Connecting External Devices/Your TV via
HDMI
21 HDMI Function
16
22 Connecting to your TV
23 Connecting a DVD or BD(Blu-ray) Player
24 Connecting a Cable, Satellite or Set-top Box
25 Connecting a CD Player
26 Connecting 5.1 Channel Devices
27 Connecting an iPod
28 Connecting the FM Antenna
29 Before Using the AV Receiver
29 Audio Setup
30 Selecting Digital/Analog Input
BASIC FUNCTIONS OF YOUR AV
RECEIVER
29
6
HW-C500-C560S-XAA_0609.indd 6
2010-006-09
5:11:01
Download from Www.Somanuals.com. All Manuals Search And Download.
31 Setup Menu Tree
SETUP
35 Setting the Speaker Size
36 Setting the Speaker Listening Distance
37 Setting the Speaker Level
38 Setting the Test Tone
39 Setting Dolby Pro Logic II Mode
39 Setting Dolby Pro Logic II
40 Setting Tone Control
41 AV SYNC
31
41 MP3 Enhancer
41 Smart Volume
42 ASC (Auto Sound Calibration) Setup
43 DRC Setup
43 HDMI Setup
43 Variable Set
44 Using the Surround Modes
45 Using the Subwoofer Selection Button
46 Listening to the Radio
47 Using an iPod
49 Convenient Functions
50 Software Upgrade
OPERATION
44
51 Operating Your TV With the Remote Control
53 Operating your DVD or BD player with the
remote control
MISCELLANEOUS
51
54 Troubleshooting
56 Specifications
TROUBLESH5OOT4ING
APPENDIX
56
7
HW-C500-C560S-XAA_0609.indd 7
2010-006-09
5:11:01
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
FRONT PANEL
1
2
3
4
5
6
7
8
SETUP
TONE CONTROL
INPUT SELECT
ENTER
SOUND EFFECT
AUDIO
ASSIGN
S. DIRECT
/STEREO
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
ASC MIC
ASC
SELECT
MEMORY
9
10 11 12 13 14 15
16
17
Used to select a source.
INPUT SELECT
1
(FM ꢀ BD/DVD ꢀ SAT ꢀ TV ꢀ CD ꢀ AUX ꢀ 5.1 MULTI CH ꢀ IPOD AUDIO ꢀ IPOD VIDEO).
Used to move the cursor up, down, left or right and select an item in the SETUP menu.
Also used to select detailed options in the SOUND EFFECT mode and to change the tone level.
UP(,), DOWN(.),
2
3
LEFT(<), RIGHT(>), ENTER
SETUP
Displays the SETUP menu.
TONE CONTROL
SOUND EFFECT
DISPLAY
Used to set the bass, treble level and tone to on/off.
Toggles to select a surround sound mode.
Displays the speaker/audio input status, listening mode, etc
Adjusts the volume level.
4
5
6
7
8
VOLUME CONTROL
POWER
Turns the receiver on/off.
9
ASC MIC JACK
Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).
8
HW-C500-C560S-XAA_0609.indd 8
2010-006-09
5:11:01
Download from Www.Somanuals.com. All Manuals Search And Download.
ASC BUTTON
Used to select the ASC(Auto Sound Calibration) mode.
Toggles to select an input mode for the selected source.
10
11
AUDIO ASSIGN BUTTON
S.DIRECT/STEREO
BUTTON
Used to select the S.DIRECT or STEREO mode.
12
MULTI CH INPUT BUTTON Used to select a connected 5.1 multi channel player.
13
14
15
16
17
AV SYNC BUTTON
TUNING MODE BUTTON
SELECT BUTTON
Used to select the Audio Delay Mode.
Used to select the Manual or Preset mode for FM radio.
Used to change the radio frequency.
MEMORY BUTTON
Used to set a preset radio frequency.
9
HW-C500-C560S-XAA_0609.indd 9
2010-006-09
5:11:02
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
REAR PANEL
< HW-C500 >
1
2
3
4
5
6
7
iPod
8 9 10 11 12
13
14
5
15
< HW-C560S >
1
2
3
4
6
7
iPod
8 9 10 11 12
13
14
15
* All those pictures of the Rear panel are based on Model HW-C560S.
10
HW-C500-C560S-XAA_0609.indd 10
2010-006-09
5:11:02
Download from Www.Somanuals.com. All Manuals Search And Download.
FM ANTENNA JACK
Connect the FM Antenna here.
1
2
MULTI CH IN JACKS
Receives the analog audio signal from an external player with a multi-channel port.
Receives the video signal from a video player (BD/DVD, SAT, TV).
Receives digital video and audio signals simultaneously using an HDMI cable.
Outputs digital video and audio signals simultaneously using an HDMI cable.
Can be only used for firmware upgrades.
VIDEO IN JACKS
3
HDMI IN JACKS
4
HDMI OUT JACK
5
USB PORT
6
VIDEO OUT JACK
Outputs the video signal to video devices (TV, Projector etc).
Receives the component video signal.
7
COMPONENT VIDEO IN JACKS
COMPONENT VIDEO OUT JACKS
iPod JACK
8
Outputs the component video signal.
9
Receives the audio/video signal from an iPod.
Receives the digital optical audio signal.
10
11
12
13
14
15
OPTICAL IN JACKS (DIGITAL AUDIO IN)
COAXIAL IN JACK (DIGITAL AUDIO IN)
AUDIO IN JACKS
Receives the digital coaxial audio signal.
Receives the audio signal from a video player (BD/DVD, SAT, TV, CD).
Connect the subwoofer.
SUBWOOFER AUDIO OUT JACK
SPEAKER OUT TERMINALS
Speaker connection terminals.
11
HW-C500-C560S-XAA_0609.indd 11
2010-006-09
5:11:04
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
DISPLAY
1
2
3
4
5
7
6
SPEAKER INDICATORS
Displays the connected speakers.
1
2
3
4
5
6
7
LISTENING MODE INDICATORS
TUNING INDICATORS
Displays the current listening mode.
Displays the status of the current radio broadcast.
AUDIO INPUT INDICATORS
SPEAKER LEVEL INDICATOR
Displays the audio input signal type of the currently connected external audio source.
Displays the speaker level.
RADIO FREQUENCY INDICATORS Displays the current radio frequency range.
MESSAGE DISPLAY
Informs you of the status of the receiver.
12
HW-C500-C560S-XAA_0609.indd 12
2010-006-09
5:11:04
Download from Www.Somanuals.com. All Manuals Search And Download.
INSERT REMOTE CONTROL BATTERIES
* Batteries (AAA size)
Follow these precautions to avoid leaking or cracking cells:
M
Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Assuming typical TV usage, the batteries last for about one year.
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a flame.
OPERATION RANGE OF THE REMOTE CONTROL
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a
horizontal angle of up to 30° from the remote control sensor.
SETUP
TONE CONTROL
SOUND EFFECT
INPUT SELECT
ENTER
AUDIO
ASSIGN
S. DIRECT
/STEREO
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
ASC MIC
ASC
SELECT
MEMORY
INPUT SELECT
POWER
AMP/TV
TV SOURCE
DIMMER
BD/DVD
1
4
2
3
6
5
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
MUTE
TUNING
/CH
VOL
ASC
TUNER MEMORY
SETUP/MENU
SUBWOOFER
MO/ST
INFO
RETURN
EXIT
BD/DVD
SAT
TV
CD
MULTI CH
AUX
iPod
13
HW-C500-C560S-XAA_0609.indd 13
2010-006-09
5:11:04
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
TOUR OF THE REMOTE CONTROL
INPUT SELECT
TV SOURCE
POWER
15
1
16
17
AMP/TV
DIMMER
BD/DVD
2
1
2
3
6
18
19
3
4
5
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
4
20
21
5
6
7
22
23
MUTE
TUNING
/CH
VOL
8
ASC
24
25
9
10
TUNER MEMORY
SETUP/MENU
SUBWOOFER
MO/ST
INFO
26
27
11
12
13
14
RETURN
EXIT
28
BD/DVD
SAT
TV
CD
MULTI CH
AUX
iPod
14
HW-C500-C560S-XAA_0609.indd 14
2010-006-09
5:11:05
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BUTTON
Turns the receiver on/off.
1
2
Used to select the AMP/TV mode.
- If you select the AMP mode, the button will flash orange.
- If you select the TV mode, the button will flash green.
AMP/TV BUTTON
NUMBER BUTTONS
PROLOGIC BUTTON
SKIP BUTTONS
Used to select a TV channel.
3
4
5
6
7
Select the desired Dolby Pro Logic II audio mode.
Press to skip backwards or forwards on a connected DVD/BD player or iPod.
Press to stop/start playback on a connected DVD/BD player or iPod.
Mutes the sound of a connected device.
STOP/PLAY BUTTON
MUTE BUTTON
VOLUME CONTROL BUTTONS Adjusts the volume of the selected device.
8
9
SUBWOOFER BUTTON
TUNER MEMORY BUTTON
SETUP/MENU BUTTON
Used to select the Subwoofer.
Used to set a preset radio frequency.
Displays the SETUP menu.
10
11
UP/DOWN/LEFT/RIGHT
BUTTONS
Used to navigate the menus.
12
13
14
RETURN BUTTON
Used to return to the previous menu from the SETUP menu.
Used to select an input source.
FUNCTION SELECTOR
BUTTONS
Toggles to find and select an input source.
Press to select a connected TV's video source.
INPUT SELECT,
15
16
TV SOURCE BUTTON
DIMMER BUTTON
Adjusts the brightness of the display.
Used to select the BD/DVD mode.
BD/DVD BUTTON
- If you select the BD mode, the button will flash orange.
- If you select the DVD mode, the button will flash green.
17
SLEEP BUTTON
Used to set the Sleep Timer.
18
19
20
21
22
23
24
25
26
27
28
AUDIO ASSIGN BUTTON
DSP BUTTON
Toggles to select an input mode for the selected source.
Used to select the SFE mode.
SEARCH BUTTONS
PAUSE BUTTON
Press to search backwards or forwards.
Pauses playback on a connected device.
TUNING/CHANNEL BUTTONS Used to change the radio broadcasting frequency or TV channel.
ASC BUTTON
MO/ST BUTTON
INFO BUTTON
ENTER BUTTON
EXIT BUTTON
Used to set the Auto Sound Calibration function.
Select MONO or STEREO for radio broadcasts.
Display information on the connected device currently being used.
Used to select an item in the SETUP menu.
Exits the SETUP menu.
15
HW-C500-C560S-XAA_0609.indd 15
2010-006-09
5:11:05
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
This section involves various methods of connecting the AV receiver to other
external components.
Before moving or installing the product, be sure to turn off the power and
disconnect the power cord.
SPEAKER POSITIONING
* Speakers are provided with model HW-C560S only. Model HW-C500 does not come with speakers.
6.6~9.8 feet (2~3m)
AV
RECEIVER
SETUP
I
N
P
U
T
S
E
L
E
C
T
ENTER
T
O
N
E
C
O
N
T
R
O
L
S
O
U
N
D
E
F
F
E
C
T
A
S
C
M
I
C
ASC
AS
A
U
S
D
I
G
O
N
S
/
.
S
D
T
I
R
R
E
E
C
O
T
MUIN
L
P
T
U
I
C
T
H
SY
A
N
C
T
M
U
O
N
D
IN
E
G
SELECT
MEMORY
SL
SR
Position of AV Receiver
Place the AV Receiver on a dedicated stand or rack.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the center speaker or place them slightly
in front of the center speaker.
16
HW-C500-C560S-XAA_0609.indd 16
2010-006-09
5:11:05
Download from Www.Somanuals.com. All Manuals Search And Download.
Center speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects
and sound will not come from them all the time.
When you attach the speakers to the wall, make sure to fasten them tightly so they do not fall off.
M
Speaker Configuration
For the best surround-sound experience, you should connect five speakers and a powered subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
2 speakers
3 speakers
4 speakers
5 speakers
If you place a speaker near your TV set, screen color may be distorted because of the magnetic field generated
by the speaker. If this occurs, place the speaker away from your TV set.
M
17
HW-C500-C560S-XAA_0609.indd 17
2010-006-09
5:11:06
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING THE SPEAKERS (HW-C500)
FRONT (R) SURROUND (R)
SUBWOOFER
(not supplied)
SURROUND (L) FRONT (L)
(not supplied) (not supplied)
(not supplied) (not supplied)
ACTIVE SUBWOOFER
(not supplied)
SW
CENTER
(not supplied)
iPod
Model HW-C500
AV Receiver
HW-C500
Speakers are provided with model HW-C560S only. Model HW-C500 does not come with speakers. Contact a Samsung
Electronics retailer for purchasing.
M
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects into
the duct (hole).
M
Never touch speaker terminals while the power is on. Doing so could result in electric shock.
Make sure the polarities (+ and -) are correct.
Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the
red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the AV Receiver.
Black
Red
•
Make sure the colors of the speaker terminals on the back of the
AV receiver match the colors of the connecting plugs.
18
HW-C500-C560S-XAA_0609.indd 18
2010-006-09
5:11:07
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE SPEAKERS (HW-C560S)
FRONT (R) SURROUND (R) SUBWOOFER
SURROUND (L) FRONT (L)
PS-FC560S
PS-RC560S
PS-WC560S
PS-RC560S PS-FC560S
ACTIVE SUBWOOFER
(not supplied)
SW
Model HW-C560S
CENTER
PS-CC560S
AV Receiver
HW-C560S
PS-FC560S
PS-CC560S
PS-RC560S
PS-WC560S
iPod
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
SUBWOOFER
The Active Subwoofer is sold separately. Contact a Samsung Electronics retailer for purchasing.
M
Connecting the Speakers
1
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into
the red (+) terminal, and then release the tab.
2
3. Press down the terminal tab on the back of the AV Receiver.
Black
Red
4. Insert the one wire into the terminal + and the other one into the
terminal -.
•
Make sure the colors of the speaker terminals on the back of the
AV receiver match the colors of the connecting plugs.
Speaker
3
4
Keep the subwoofer speaker out of reach of children to prevent them
from inserting their hands or objects into the duct (hole).
Never touch speaker terminals while the power is on. Doing so could
result in electric shock.
M
Make sure the polarities (+ and -) are correct.
AV Receiver
19
HW-C500-C560S-XAA_0609.indd 19
2010-006-09
5:11:09
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING EXTERNAL DEVICES/YOUR TV VIA HDMI
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set-top
box and more.
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound quality as it was
originally created in the digital source.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital video and audio.
DVD or
Blu-ray Player
SAT
Game console
or
Camcorder
(Cable/Satellite/Set-top box)
HDTV Tuner
(HDTV Terrestrial Receiver)
ONLY USE FOR
FIRMWARE UPDATE
iPod
•
Connect it if you want
to use Anynet+.
OPTICAL
OUT
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV must
support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
A TV with a DVI-D jack (TV not supporting HDCP)
Video
-
Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is protected
by CPPM, use a player supporting CPPM.
M
The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
20
HW-C500-C560S-XAA_0609.indd 20
2010-006-09
5:11:12
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI FUNCTION
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support
Anynet+.
1. Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 20)
2. Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
•
You can operate the volume on the AV receiver by using the Volume buttons on the TV remote
control.
To turn on Anynet+
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select HDMI ANYNET+, and then press the ENTER or ► button.
5. Press the ▲▼ buttons to set ANYNET+ to ON.
- To exit setup mode-
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV receiver using
the TV’s remote control. This function is available only in connection with Samsung TV and DVD player
supporting Anynet +(HDMI-CEC).
M
Please check your TV for the n logo. If your TV has an n logo, then it supports the Anynet+
function.
When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+ installed).
Otherwise, it can cause a malfunction.
21
HW-C500-C560S-XAA_0609.indd 21
2010-006-09
5:11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING TO YOUR TV
iPod
or
or
COMPONENT VIDEO
OPTICAL AUDIO
OUT OUT
IN
IN
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not
supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the
Component Video Input jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the
Video Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
22
HW-C500-C560S-XAA_0609.indd 22
2010-006-09
5:11:15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING A DVD OR BD(Blu-ray) PLAYER
COMPONENT
IN
VIDEO
IN
or
iPod
or
DVD or BD Player
COMPONENT OPTICAL
OUT OUT
AUDIO
OUT
VIDEO
OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (BD/DVD) (PR, PB and Y)
jacks on the back of your AV Receiver to the Component Video Output jacks on your DVD/BD player.
OR
Connect a Video cable from the VIDEO IN (BD/DVD) jack on the back of your AV Receiver to the Video
Output jack on your DVD/BD player.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your AV Receiver to the Digital Output of the DVD/BD player.
OR
Connect AUDIO IN (BD/DVD) on your AV Receiver to the Audio Out of the DVD/BD player.
23
HW-C500-C560S-XAA_0609.indd 23
2010-006-09
5:11:16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING A CABLE, SATELLITE OR SET-TOP BOX
COMPONENT
IN
VIDEO
IN
or
iPod
or
SAT(Cable/Satellite/Set-top box)
COMPONENT OPTICAL
AUDIO
OUT
VIDEO
OUT
OUT
OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks
on the back of your AV Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable from the VIDEO IN (SAT) jack on the back of your AV Receiver to the Video
Output jack on your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your AV Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your AV Receiver to the Audio Out of the SAT.
Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
M
If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
24
HW-C500-C560S-XAA_0609.indd 24
2010-006-09
5:11:18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING A CD PLAYER
CD player
AUDIO
OUT
COAXIAL
OUT
or
iPod
Audio Connection
Connect the Digital Input (COAXIAL) on your AV Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your AV Receiver to the Audio Out of the CD player.
If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the main
unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
M
25
HW-C500-C560S-XAA_0609.indd 25
2010-006-09
5:11:20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING 5.1 CHANNEL DEVICES
You can connect the AV receiver to a DVD player, SUPER AUDIO CD player or other device with 5.1 channel output.
C
SW
iPod
SW
C
FRONT
SURROUND
5.1 CH
SUB
WOOFER
CENTER
5.1 Channel device
26
HW-C500-C560S-XAA_0609.indd 26
2010-006-09
5:11:22
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AN iPod
You can listen to audio from an iPod through the main unit. For iPod operation with your receiver, see this page and
47 ~ 48.
iPod
iPod
1. Connect the iPod dock connector to the iPod jack on your reciever.
2. Place the iPod in the Dock.
•
If you want to play a movie stored in your iPod player, you should set the player's TV Out option to
On before inserting it into the dock. See page 48.
3. Press the iPod button on the remote control.
•
You can also use the INPUT SELECT button on the main unit.
The mode switches as follows :
FM ¨ BD/DVD ¨ SAT ¨ TV ¨ CD ¨ AUX ¨ 5.1 MULTI CH ¨ IPOD AUDIO ¨ IPOD VIDEO
Disconnecting an iPod
Follow the steps below to prevent damage to an iPod and data when disconnecting from your
AV receiver.
1. Press the INPUT SELECT button on the main unit to switch to a mode other than IPOD AUDIO or
IPOD VIDEO.
OR
1. Turn off the AV Receiver.
2. Disconnect the iPod player from the iPod dock, or remove the iPod dock connector from the AV
receiver.
You must have the VIDEO (Monitor) output connected to your TV to view iPod video. See page
23.
M
Adjust the volume to a moderate level before you connect your iPod and AV Receiver.
When the unit is powered on and you connect an iPod, the unit will charge your iPod's battery.
Make sure to connect the dock connector so that the label “SAMSUNG” faces upward.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to an iPod and
has been certified by the developer to meet Apple performance standards.
“Works with iPhone” means that an electronic accessory has been designed to connect specifically to an
iPhone and has been certified by the developer to meet Apple performance standards.
27
HW-C500-C560S-XAA_0609.indd 27
2010-006-09
5:11:24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
CONNECTING AN iPod (Continued)
iPod models that are compatible with HW-C500/HW-C560S
"Made for iPod" means that the dock has been designed to connect specifically for the iPod and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
M
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
CONNECTING THE FM ANTENNA
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or
other rigid surface.
FM antenna (supplied)
iPod
Do not place the antenna cable close to the power cord. Keep it as far away as possible.
If you experience poor FM reception, use an external antenna.
M
28
HW-C500-C560S-XAA_0609.indd 28
2010-006-09
5:11:26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic functions of your AV Receiver
BEFORE USING THE AV RECEIVER
Turning On/Off
Connect the power plug to the outlet.
Press the POWER button on the main unit for 2 seconds.
•
This unit will be turned on or set to Standby mode.
•
You can also turn the unit on/off by pressing the POWER button on the remote control.
Remote control functions
You can operate your AMP (this AV receiver)/ TV and BD(Samsung only)/ DVD player with this remote control.
See pages 51 ~ 53 for more details.
To select a function
Method 1
Press the INPUT SELECT button.
•
Each time you press this button, FM ¨ BD/DVD ¨ SAT ¨ TV ¨ CD ¨ AUX ¨ 5.1 MULTI CH ¨
IPOD AUDIO ¨ IPOD VIDEO will be selected in turn.
Method 2
Press the TUNING/CH, BD/DVD, SAT, TV, CD, MULTI CH, AUX or iPod button.
•
You can directly select the desired function.
AUDIO SETUP
Selecting a source device and connection jack
Select the external devices you have connected to the receiver.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches
between SETUP ENTER and SETUP OFF.
Æ
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select AUDIO SETUP, and then press
the ENTER or ► button.
4. Press the ▲▼ buttons to select a desired jack.
•
The source device switches as follows; BD/DVD, SAT, TV, CD
- To exit setup mode -
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
M
You can also use SETUP, ,,.,
,
, ENTER on the front of your AV Receiver.
<>
29
HW-C500-C560S-XAA_0609.indd 29
2010-006-09
5:11:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic functions of your AV Receiver
SELECTING DIGITAL/ANALOG INPUT
You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit.
POWER
1. Press the INPUT SELECT button to select a desired function (BD/DVD,
SAT,TV, CD). See page 29.
AMP/TV
DIMMER
BD/DVD
2. Press the AUDIO ASSIGN button on the remote control to select the external
device you have connected.
1
4
2
5
3
6
•
Each time you press this button, the input mode changes as follows:
•
•
For BD/DVD function
For SAT function
Ä
Ä
Ä
Ä
Ä
•
•
For TV function
For CD function
Ä
Ä
M
You can also change the input mode by pressing the AUDIO ASSIGN button on the front of your AV Receiver.
You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio component to the optical
or coaxial digital audio input jack on the main unit.
30
HW-C500-C560S-XAA_0609.indd 30
2010-006-09
5:11:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
For your convenience, you can set this AV receiver's features for the best use.
SETUP MENU TREE
Here’s a quick look at how the setup menus are organized on your AV Receiver.
AUDIO SETUP
BD/DVD
OPT 1,2,3
OPT 1,2,3
OPT 1,2,3
OPT 1,2,3
COAX
COAX
COAX
COAX
SAT
TV
CD
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
TONE CONTROL
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
31
HW-C500-C560S-XAA_0609.indd 31
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
SETUP MENU TREE (Continued)
AUDIO SETUP
SPK SIZE
FRONT
CENTER
SURR
LARGE
LARGE
LARGE
SMALL
SMALL
SMALL
NONE
NONE
SUBW
YES
NO
CROVR
60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 180Hz, 200Hz
1 ~ 30 FT (1 foot steps) , default : 10 FT
SPK DISTANCE
F.L
F.R
CEN
S.L
S.R
S.W
SPK LEVEL
F.L
F.R
CEN
S.L
-10 ~ +10dB (1dB step) , default : 00dB
S.R
S.W
TEST TONE
DPLII SETUP
AUTO
MANUAL
TONE CONTROL
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
32
HW-C500-C560S-XAA_0609.indd 32
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU TREE (Continued)
AUDIO SETUP
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
PANORAMA
DIMENSION
C- WIDTH
OFF
ON
-7 ~ 0 ~ +7
0~7
OFF
TONE CONTROL
TONE
BASS
ON
-6dB ~ +6dB (1dB Step)
-6dB ~ +6dB (1dB Step)
TREBLE
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
33
HW-C500-C560S-XAA_0609.indd 33
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
SETUP MENU TREE (Continued)
AUDIO SETUP
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
TONE CONTROL
A/V SYNC
SYNC OFF ~ SYNC 240MS (10MS Step)
OFF
OFF
ON
ON
MP3 ENHANCER
SMART VOLUME
START
MAX
EQ ON / EQ OFF
STD
ASC SETUP
DRC SETUP
MIN
SYNC
AUDIO
HDMI SETUP
ON
OFF
TV
AVR
ANYNET+
ON
ON
OFF
OFF
VARIABLE SET
34
HW-C500-C560S-XAA_0609.indd 34
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE SPEAKER SIZE
Signal outputs and frequency response from the speaker will be adjusted according to your speaker configuration and whether
certain speakers are used or not.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
3. Press the ▲▼ buttons to select SPK SIZE, and then press the ENTER
or
►
button.
4. Press the ▲▼ buttons to select the speaker you want, and then press
the ENTER or ► button.
•
Each time you press the ▲▼ buttons, FRONTÆCENTER Æ SURR Æ
SUBW Æ CROVR will be selected in turn.
5. Press the ▲▼ buttons to set the mode (LARGE, SMALL etc.) for the
selected speaker.
6. Repeat steps 3-5 to set the mode for each speaker.
- To exit setup mode -
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
Setting the Speaker
SPEAKER
FRONT (Front)
Possible Settings
LARGE, SMALL
Default Setting
SMALL
SMALL
SMALL
YES
CENTER (Center)
LARGE, SMALL, NONE
LARGE, SMALL, NONE
YES, NO
SURR (Surround)
SUBW (Subwoofer)
CROVR (Crossover Frequency)
60, 80, 100,120, 150, 180, 200(Hz) 100Hz
•
•
•
•
•
•
LARGE : Select when using large speakers. You can listen to full range sound.
SMALL : Select this when using small speakers
NONE : Select when no speaker is used
YES (subwoofer) : Select when using the subwoofer speaker.
NO (subwoofer) : Select when not using the subwoofer speaker.
CROVR : Select the crossover frequency for the best bass response in your room.
You can also use SETUP,
,,., <, >, ENTER on the front of your AV Receiver.
M
When the Front speaker is only set to LARGE, you can select LARGE of other speakers.
35
HW-C500-C560S-XAA_0609.indd 35
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
SETTING THE SPEAKER LISTENING DISTANCE
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio
signals from the center and surround speakers.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
Æ
3. Press the ▲▼ buttons to select SPK DISTANCE, and then press the
ENTER or
►
button.
4. Press the ▲▼ buttons to select the speaker you want, and then press
the ENTER or ► button.
•
Each time you press the ▲▼ buttons, F.L Æ F.RÆ CEN Æ S.L Æ S.R
Æ S.W will be selected in turn.
5. Press the ▲▼ buttons to set the Speaker Distance.
•
For the FRONT LEFT, FRONT RIGHT, CENTER, SURR. LEFT,
SURR. RIGHT and SUBWOOFER Speakers, you can set the distance
from the speaker to listening position between 1ft ~ 30ft (0.3~9.0m) in
intervals of 1ft (0.3m).
- To exit setup mode -
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
- Setting Speaker Distance -
Set the distance from the speaker to listening position in intervals of 1ft(0.3m).
• F.L (front left) : 1ft ~ 30ft
• F.R (front right) : 1ft ~ 30ft
• S.L (surround left) : 1ft ~ 30ft
• CEN (center) : 1ft ~ 30ft
• S.R (surround right) : 1ft ~ 30ft
• SW (subwoofer) : 1ft ~ 30ft
If the listening position is beyond the range of the speaker distance setup, set the speaker distance to the
maximum.
M
The distance range of the overall speaker system is determined based on the F.L(front left) speaker
distance from the listening position.
36
HW-C500-C560S-XAA_0609.indd 36
2010-006-09
5:11:31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE SPEAKER LEVEL
You can set the balance and level of speakers.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
Æ
Æ
3. Press the ▲▼ buttons to select SPK LEVEL, and then press the ENTER
or
►
button.
4. Press the ▲▼ buttons to select the speaker you want, and then press the
ENTER or ► button.
•
Each time you press this button, F.L Æ F.RÆ CEN Æ S.L Æ S.R Æ
S.W will be selected in turn.
5. Press the ▲▼ buttons to set the Speaker Level mode.
•
•
You can adjust it from -10 to +10dB in 1 step increments.
The sound gets quieter at -10dB and louder at +10dB.
- To exit setup mode -
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
- Setting Speaker Level -
• F.L (front left) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• CEN (center) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
37
HW-C500-C560S-XAA_0609.indd 37
2010-006-09
5:11:32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
SETTING THE TEST TONE
Use the test tone to check the speaker connection status or level.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
Æ
Æ
3. Press the ▲▼ buttons to select TEST TONE, and then press the ENTER
or
►
button.
4. Press the ▲▼ buttons to select the option you want, and then press the
ENTER or button.
►
•
AUTO : Test signal will be automatically output as follows; F.L Æ CEN
Æ S.W ÆF.R Æ S.R Æ S.L.
- During test tone output, press the ▲▼ buttons to adjust the speaker
output level from -10 to +10 dB by 1 step.
•
MANUAL : Enables you to adjust the output level of the speaker
manually.
1) Press the ENTER button to select the speaker you want.
Each time you press the ENTER button, F.L Æ CEN Æ S.W ÆF.R Æ
S.R Æ S.L will be selected in turn.
2) Press the ▲▼ buttons to set the Test Tone mode you want.
You can adjust the speaker output level from -10 to +10dB by 1 step.
The sound gets quieter at -10dB and louder at +10dB.
- Test Tone Output -
• F.L (front left) : -10 ~ +10dB
• CEN (center) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
- To stop test tone -
•
Press the SETUP/MENU button once.
SETUP OFF appears on the display and test tone stops.
38
HW-C500-C560S-XAA_0609.indd 38
2010-006-09
5:11:32
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING DOLBY PRO LOGIC II MODE
This mode provides 5.1 channel sound from 2 channel sources.
Press the PROLOGIC button on the remote control.
•
•
•
•
•
MOVIE : Adds realism to the movie soundtrack.
MUSIC : Provides 5.1 channel surround sound for digital, analog or existing stereo sources.
GAME : Enhances the excitement of the game’s sound.
MATRIX : You will hear 5.1 channel surround sound.
PL (Pro Logic) : You will experience a surround effect with 5.1 channel surround sound.
SETTING DOLBY PRO LOGIC II
This function works only in Dolby Pro Logic ll MUSIC mode.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
Æ
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select DPLII SETUP, and then press the
ENTER or
►
button.
4. Press the ▲▼ buttons to select the option you want, and then press the
ENTER or button.
PANORAMA : You can set it ON or OFF.
►
•
(This mode extends the front stereo image to include the surround
speakers for an exciting "wraparound" effect with side wall imaging.)
Æ
Æ
•
•
DIMENSION : You can set from -7 to +7.
(Incrementally adjusts the sound field (DSP)from the front or surround.)
C- WIDTH : You can set from 0 to 7.
(This sets the width of the center sound image. The higher the setting,
the less sound comes from the center speaker.)
PANORAMA, DIMENSION and CENTER WIDTH settings are enabled only if the mode is set to MUSIC.
You cannot use Dolby Pro Logic II mode for multi channel signals such as Dolby Digital and DTS.
Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.
M
39
HW-C500-C560S-XAA_0609.indd 39
2010-006-09
5:11:32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
SETTING TONE CONTROL
This will enable you to adjust the bass and treble level.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
3. Press the ▲▼ buttons to select TONE CONTROL, and then press the
ENTER or
►
button.
4. Press the ▲▼ buttons to select the option you want, and then press the
ENTER or ► button.
•
Each time you press this button, TONE Æ BASS Æ TREBLE will be
selected in turn.
5. Press the ▲▼ buttons to set the Tone Control mode you want.
•
•
•
If it is set to the TONE OFF, Tone Control function will be disabled.
You can adjust it from -6 to +6dB by 1 step.
The sound gets quieter at -6dB and louder at +6dB.
- To exit setup mode -
•
Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
The Tone Control function can be applied to all channels except for the subwoofer.
M
40
HW-C500-C560S-XAA_0609.indd 40
2010-006-09
5:11:33
Download from Www.Somanuals.com. All Manuals Search And Download.
AV SYNC
Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio delay time
to match the video.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
Æ
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select A/V SYNC, and then press the ENTER
or ► button.
4. Press the ▲▼ buttons to set the A/V Sync mode you want.
•
You can adjust it from OFF to 240MS in 10MS steps.
MP3 ENHANCER
This also helps enhance your sound experience (ex. mp3 music). Use this if you want to hear better sound from
a low quality mp3 source.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
Æ
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select MP3 ENHANCER, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
SMART VOLUME
This will regulate and stabilize the volume level against a drastic volume change when changing channels or
during a scene transition.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
3. Press the ▲▼ buttons to select SMART VOLUME, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
41
HW-C500-C560S-XAA_0609.indd 41
2010-006-09
5:11:33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
ASC (AUTO SOUND CALIBRATION) SETUP
By setting the ASC function just once when you relocate or install the unit, you can have the unit automatically
recognize the distance between speakers, levels between channels, and frequency characteristics to create a
5.1-channel sound field optimized for your environment.
- Before Setting -
1. Plug the ASC microphone into the ASC MIC jack.
2. Place the ASC microphone at the listening position.
3. Press the ASC button on the front panel, and then press the ENTER button.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
Æ
3. Press the ▲▼ buttons to select ASC SETUP, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ASC START, and then press the
ENTER button.
•
To create the optimal 5.1 channel sound field, the selections are in the
following sequence:
L ➞ C ➞ R ➞ SR ➞ SL ➞ SW
•
EQ ON : The ASC(Auto Sound Calibration) EQ mode is set to on.
EQ OFF: The ASC(Auto Sound Calibration) EQ mode is set to off.
5. If you see a ASC READY message on the screen, press the ENTER button to apply the measurement value.
And then unplug the ASC microphone.
ASC
Microphone
To cancel the ASC (Auto Sound Calibration) setup.
This will be automatically reverted if you press the RETURN button.
* If ASC error occurs, see "ASC Error List" on page 55.
Setting the ASC function takes about 3 minutes.
Because the volume level of the tone is fixed during the ASC setup, you cannot adjust the volume using the volume control.
M
42
HW-C500-C560S-XAA_0609.indd 42
2010-006-09
5:11:33
Download from Www.Somanuals.com. All Manuals Search And Download.
If the ASC microphone is disconnected during the ASC setup, the setup will be canceled.
You can also press the ASC button on the remote control to use this function.
DRC SETUP
You can use this function to enjoy Dolby Digital sound when watching movies
at low volume at night.DRC compresses the audio to make the loudest
sounds quieter and the quietest sounds louder.
Æ
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select DRC SETUP, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to set the DRC Setup mode you want.
•
STD : Sets DRC effect to standard. •MAX : Sets DRC effect to maximum.
•
MIN : Sets DRC effect to minimum.
HDMI SETUP
Use this if you want to receive audio from HDMI connected external devices.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select the option you want, and then press the ENTER or ► button.
5. Press the ▲▼ buttons to set the HDMI Setup mode you want.
•
HDMI AUDIO : AVR(Audio Video Receiver), TV
This preference determines whether audio received at the HDMI IN is output by the HDMI OUT.
If you want to listen to audio from an HDMI connected external device through your HDMI connected TV's
speakers, set it to TV. Otherwise, leave it on AVR to listen to audio from the A/V receiver.
- AVR : HDMI audio is not output
- TV : HDMI audio is output
•
•
HDMI ANYNET+ : ON, OFF
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control.
- ON : Anynet+ is enabled.
HDMI SYNC : ON, OFF
- OFF : Anynet+ is disabled.
The AV receiver can be set to automatically correct any delay between the video and the audio, based on the
data from the connected TV.
- ON : HDMI Sync is enabled.
- OFF : HDMI Sync is disabled.
HDMI Audio is enabled only if both the HDMI INPUT and HDMI OUT are connected properly and working normally.
This function works only if your HDMI-compatible TV supports HDMI Sync.
M
VARIABLE SET (Low Power Consumption SETUP)
This function enhances electric power efficiency.
1. Press the SETUP/MENU button.
•
Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select VARIABLE SET, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
•
ON :This is Samsung's electric power efficiency function, you can save about 30 % for power consumption.
•
OFF: Normal power efficiency function.
This function is not available after the Tone Control, Speaker Level, SFE mode or ASC is changed from the factory setting.
M
43
HW-C500-C560S-XAA_0609.indd 43
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
USING THE SURROUND MODES
Using the SOUND EFFECT button on the front of the main unit
Selecting the SFE mode
1. Press the SOUND EFFECT button to select SFE.
•
Each time you press this button, SFE Æ DPLII will be selected in turn.
2. Press the UP/DOWN ( ,,. ) button.
•
•
Each time you press the UP/DOWN ( ,,. ) button,
STEREO Æ HALL 1 Æ HALL 2 Æ J.CLUB Æ CHURCH Æ ROCK Æ CLASSIC Æ LIVE Æ
GAME Æ MOVIE Æ CONCERT Æ STADIUM will be selected in turn.
You can also select the SFE mode by pressing the DSP button on the remote control.
Selecting the DPLII mode
1. Press the SOUND EFFECT button to select DPLII.
•
Each time you press this button, SFE Æ DPLII will be selected in turn.
2. Press the UP/DOWN ( ,,. ) button.
•
•
Each time you press the UP/DOWN ( ,,. ) button, MUSIC Æ GAME Æ MATRIX Æ PL Æ
MOVIE will be selected in turn.
You can also select the DPLll mode by pressing the PROLOGIC button on the remote control.
You cannot use Dolby Pro Logic ll mode for multi channel signals such as Dolby Digital and DTS.
M
Pro Logic works only for BITSTREAM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
Using the S.DIRECT/STEREO button on the front of the main unit
Press the S.DIRECT/STEREO button.
•
•
•
Each time the button is pressed, the mode switches between the S. DIRECT mode and the STEREO
mode.
S.DIRECT : Outputs 2 CH PCM audio signal without any signal processing, providing higher audio
quality. This is useful for obtaining the best sound from a connected CD player.
STEREO : Outputs sound of the selected source in 2 CH stereo.
44
HW-C500-C560S-XAA_0609.indd 44
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SURROUND MODES (Continued)
Surround Mode and Input Signal Chart
o = active, – = inactive
Output Channel
Display Information
Channel Status
Surround Mode
Input Signal
Decoding
SL
SR
Display Signal
Format
L/R
C
SUBW
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
L.PCM 96KHz
Analog
Dolby Digital 5.1
Pro Logic II
Pro Logic II
Pro Logic II
Pro Logic II
DD+SFE
DD+SFE
SFE
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
–
–
–
O
O
O
O
O
O
O
O
O
–
–
–
–
–
O
O
O
O
O
O
O
O
O
O
O
O
O
O
DIGITAL
DIGITAL
DIGITAL
L.PCM
Analog
DIGITAL
DIGITAL
L.PCM
Analog
DIGITAL
DIGITAL
L.PCM
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, R, SW
DOLBY
(MUSIC, GAME,
MATRIX, PL, MOVIE)
SFE
SFE
Stereo
Stereo
Stereo
Stereo
Stereo
L, R, SW
STEREO
L, R, SW
L.PCM
Analog
L, R, SW
L, R, SW
•
L/R : Front Speaker (Left/Right)
C : Center Speaker
SL/SR : Surround Speaker (Left/Right)
SW : Subwoofer
Channel status displays are dependent on the speaker configuration.
SFE mode works with 2-ch signals.
M
USING THE SUBWOOFER SELECTION BUTTON
You can set the subwoofer to on/off.
Press the SUBWOOFER button.
45
HW-C500-C560S-XAA_0609.indd 45
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
LISTENING TO THE RADIO
You can listen to the radio by using either automatic or manual tuning.
1. Press the INPUT SELECT button to select FM.
2. Select a frequency (radio broadcast).
•
•
•
Preset tuning :
Press the #,$ buttons on the remote control to select the preset frequency.
Manual tuning 1 (Automatic tuning):
Press and hold the TUNING/CH ( .,, ) buttons on the remote control to automatically tune in a frequency.
Manual tuning 2 :
Press the TUNING/CH ( .,, ) buttons on the remote control to increase or decrease the frequency step by
step.
You can also use the SELECT ( .,, ) buttons on the main uint to change the radio frequency.
M
To Listen in mono/stereo
Press the MO/ST button on the remote control.
•
•
•
Each time you press this button, STEREO or MONO will be selected in turn.
If you select MONO in an area with weak reception, it will help to reduce noise.
This function works only with the remote control.
Presetting radio stations
You can preset up to 30 FM stations.
E.g.: Setting station FM 89.10 in preset 2.
1. Press the INPUT SELECT button to select FM.
2. Press the TUNING/CH ( .,, ) buttons on the remote
control to select 89.10.
•
Refer to step 2 above to tune in automatically and manually.
Æ
Æ
Æ
3. Press the MEMORY button on the main unit.
•
•
You can also use the TUNER MEMORY button on the
remote control.
Tuner number will blink on the display.
4. Press the TUNING/CH ( .,, ) buttons on the remote
control to select preset 2.
•
You can select from presets 1 to 30.
5. Press the MEMORY button on the main unit.
•
Tuner number will disappear and station 89.10 will be
saved in preset 2.
6. To preset other stations, repeat steps 2 to 5.
To Listen to Preset Station
•
Press the TUNING MODE button to select PRESET and press the SELECT ( .,, ) buttons.
46
HW-C500-C560S-XAA_0609.indd 46
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
USING AN iPod
You can enjoy playback of your iPod using the supplied remote control.
Listening to Music (iPod audio function)
You can play music files stored in the iPod player by connecting it to the AV
receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
Receiver.
2. Place the iPod in the dock.
•
Your iPod is automatically turned on.
3. Press the INPUT SELECT button on the remote control to select
IPOD AUDIO mode.
4. Press the PLAY button on the remote control to play.
•
The AV receiver starts playing from the first track of the iPod player.
5. You can use the remote control to control simple playback functions such as the PLAY, PAUSE,
STOP, SKIP (#,$) buttons.
See page 28 for compatible iPods.
M
Compatibility depends on the software version of your iPod.
You can also select iPod by pressing the iPod button on the remote control.
47
HW-C500-C560S-XAA_0609.indd 47
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
USING AN iPod (Continued)
Watching a Movie (iPod Video function)
You can play video files stored in the iPod player on a TV by connecting
it to the AV receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
receiver.
2. In the iPod screen, move to Videos > Settings and set the TV Out
option to On.
3. Place the iPod in the dock.
<iPod Screen>
4. Press the INPUT SELECT button on the remote control to select
IPOD VIDEO mode.
5. Set the AV IN option of the TV connected to the AV receiver to
COMPOSITE.
Follow the iPod onscreen guide through the following steps.
6. Press the S,T buttons on the remote control to select Videos and
press the ENTER button.
7. Press the S,T buttons on the remote control to select Movies and press
the ENTER button.
8. Press the S,T buttons to select the file to play and press the ENTER
button.
•
The iPod's video files will be played on the TV screen.
9. You can use the remote control to control simple playback functions
such as the PLAY, PAUSE, STOP, and SKIP (#,$) buttons.
•
If you press the PREV button within 3 seconds after the playback,
the player will stop playing and return to the list screen.
If you press the PREV button 3 seconds or later after the playback,
the player will move to the start screen of the current file.
<iPod Screen>
•
•
Press the STOP button to stop playing and return to the list screen.
Press the RETURN button to return to the previous menu.
You must have the VIDEO (Monitor) output connected to your TV to view iPod video.
M
See page 28 for compatible iPods.
Compatibility depends on the software version of your iPod.
When the current file is played to the end, the next file will not be played automatically.
To play the next file, select a file to play in the list screen of the iPod player.
No other screen than the playback one will appear on the TV screen. Check other screens on
the iPod player.
48
HW-C500-C560S-XAA_0609.indd 48
2010-006-09
5:11:35
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVENIENT FUNCTIONS
Sleep timer function
You can set the time that this unit will shut itself off.
4
5
6
Press the SLEEP button.
•
SLEEP : OFF Æ 15 Æ 30 Æ 45 Æ 60 Æ 90 Æ 120 M (MIN) will be
selected in turn.
7
9
PROLOGIC
AUDIO ASSIGN
DSP
0
To check sleep timer
Press the SLEEP button.
•
•
The remaining time before this unit will shut itself off is shown on the display.
Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
Press the SLEEP button until SLEEP OFF appears on the display.
•
Mute function
This function is useful when answering a doorbell or telephone call.
Press the MUTE button.
ASC
•
MUTE appears on the display.
TUNING
/CH
VOL
To output sound again
Press the MUTE button again.
•
MUTE will disappear and sound will output.
Adjust the display
You can adjust the brightness of the display.
INPUT SELECT
TV SOURCE
POWER
Press the DIMMER button.
•
Each time you press this button, the brightness changes as follows :
Dark Æ Bright.
AMP/TV
BD/DVD
1
2
3
SLEEP, Mute and the Adjust Display functions can only be operated with the remote control.
M
49
HW-C500-C560S-XAA_0609.indd 49
2010-006-09
5:11:36
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Reset function
SLEEP
When the Power is on,
7
8
PROLOGIC
AUDIO ASSIGN
DSP
1. Press the MUTE button.
0
•
MUTE appears on the display.
2. Press the 9 button five times and then press the ENTER button.
•
INITIAL : NO appears on the display.
3. Press the ▲▼ buttons to select YES.
The unit will turn off after 5 seconds.
/CH
VOL
ASC
•
TUNER MEMORY
SETUP/MENU
SUBWOOFER
MO/ST
POPUP
INFO
When the Power is Off,
RETURN
EXIT
1. Press and hold the MEMORY button on the front of your AV Receiver
for longer than 5 seconds.
•
POWER LED will blink one time.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
M
SOFTWARE UPGRADE
Samsung may offer upgrades for AV Receiver's firmware in the future.
Please visit Samsung.com or contact the Samsung call center at
1-800-SAMSUNG (726-7864) to receive information about downloading
upgrades and using a USB drive. Upgrades will be possible by
connecting a USB drive to the USB port located on your AV Receiver.
Insert a USB drive containing the firmware upgrade into the USB port
on the back of the main unit.
M
Please be careful to not disconnect the power or remove the USB
drive while upgrades are being applied. The main unit will turn off
automatically after completing the firmware upgrade.
When software is upgraded, settings you have made will return to
their default (factory) settings. We recommend you write down your
settings so that you can easily reset them after the upgrade.
If you failed software upgrade, it is strongly recommended whole USB data format to FAT16 and retry software upgrade.
The NTFS USB File System can not be supported.
Depending on the manufacturer, the USB may not be supported.
50
HW-C500-C560S-XAA_0609.indd 50
2010-006-09
5:11:37
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous
OPERATING YOUR TV WITH THE REMOTE CONTROL
1. Press the POWER button to turn on the TV.
2. Press the AMP/TV button to set the remote to TV mode.
3. Point the remote control toward the TV.
4. While holding down POWER button, enter the code corresponding to your brand of TV.
•
If there is more than one code listed for your TV in the table, enter one at a time to determine
which code works.
•
If the code matches the TV's code, the TV will be turned off.
5. If TV is turned on or off when you press the POWER button of the remote control, the setting is
completed.
•
You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).
The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
M
The remote control will work with Samsung TVs by default.
51
HW-C500-C560S-XAA_0609.indd 51
2010-006-09
5:11:38
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous
OPERATING YOUR TV WITH THE REMOTE CONTROL (Continued)
TV Brand Code List
Brand
Admiral (M.Wards)
Code Number
056, 057, 058
Brand
Luxman
Code Number
Brand
Sylvania
Code Number
018, 040, 048, 054, 059,
018
A Mark
Anam
001, 015
001, 002, 003, 004,005,
LXI (Sears)
019, 054, 056, 059, 060,
062, 063, 065, 071
060, 062
061, 095, 096
Symphonic
006, 007, 008, 009, 010,
011, 012, 013, 014
Magnavox
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
Tatung
Techwood
006
018
AOC
001, 018, 040, 048
057, 058, 081
Marantz
Matsui
040, 054
054
Teknika
TMK
003, 015, 018, 025
018, 040
Bell & Howell
(M.Wards)
Brocsonic
Candle
Cetronic
Citizen
CINEMA
Classic
Concerto
Contec
059, 060
018
003
003, 018, 025
097
003
018
046
015
003, 005, 061, 082, 083,
084
062
003
MGA
Mitsubishi/MGA
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
Toshiba
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
Vidtech
Videch
Wards
MTC
NEC
Nikei
Onking
Onwa
Yamaha
York
Yupiteru
Zenith
Zonda
Dongyang
LOWE
Coronado
Craig
003
Panasonic
006, 007, 008, 009, 054,
066, 067, 073, 074
018
Croslex
Crown
Penney
Philco
003, 054
054
003, 015, 017, 018, 048,
CURTIS MATHES
CXC
059, 061, 063
003
FINLUX
YOKO
054, 109, 114
054
054, 059, 062, 069, 090
015, 017, 018, 040, 048
Philips
Daewoo
002, 003, 004, 015,016,
LOEWE OPTA
PHONOLA
054, 114
054, 112, 114
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
040
003
Pioneer
Portland
Proton
RADIOLA
SCHNEIDER
AKAI
054, 112
054
103
108, 109, 113, 119, 120,
121
QUASAR
006, 066, 067
GRUNDIG
Daytron
Dynasty
Radio Shack
017, 048, 056, 060, 061,
075
BLAUPUNKT
108
Emerson
003, 015, 040, 046, 059,
061, 064, 082, 083, 084, 085
RCA/Proscan
018, 059, 067, 076, 077,
078, 092, 093, 094
003, 019
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
108
113
113
113
114
114
114
Realistic
Sampo
Samsung
Fisher
Funai
Futuretech
019, 065, 103
003
003
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
General Electric (GE) 006, 040, 056, 059, 066,
067, 068
040
Sanyo
FORMENTI
METZ
114
114
Hall Mark
103, 104
Hitachi
Inkel
JC Penny
JVC
015, 018, 050, 059, 069
045
056, 059, 067, 086
070
059, 061, 087, 088
Scott
Sears
Sharp
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
114
114
114
114
KTV
Signature 2000
(M.Wards)
Sony
116
KEC
KMC
003, 015, 040
015
050, 051, 052, 053, 055,
101
LG (Goldstar)
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
Soundesign
Spectricon
SSS
003, 040
001
018
52
HW-C500-C560S-XAA_0609.indd 52
2010-006-09
5:11:38
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING YOUR DVD OR BD PLAYER WITH THE REMOTE CONTROL
1. Press the POWER button to turn on the DVD (BD) player.
2. Press the BD/DVD button on the remote control to set the remote to DVD (BD) mode.
3. Point the remote control toward the DVD (BD).
4. While holding down POWER button, enter the code corresponding to your brand of DVD (BD).
•
If there is more than one code listed for your DVD (BD) in the table, enter one at a time to
determine which code works.
•
If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.
5. If DVD is turned on or off when you press the POWER button of the remote controller, the setting is
completed.
•
You can use DVD (BD) POWER, PLAY, PAUSE, STOP, SKIP, MENU and Numeric buttons (0~9).
The remote control may not work on some brands of DVD.
M
Also, some operations may not be possible depending on your brand of DVD.
The remote control will work with Samsung DVD (BD) by default.
DVD Brand Code List
Brand
DENON
Code Number
003, 032
Brand
ONKYO
Code Number
004, 014
Brand
TOSHIBA
Code Number
004, 018
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON 012
JVC
019
017
002
006
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
011
021
006
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
009, 033
004, 024
026
028
029
004, 023
007, 011, 022, 025
006
010, 013
030
KENWOOD
LG
008
001
SAMSUNG
SANYO
000, 027
002
Marantz
031
MAGNAVOX
MITSUBISHI
004
005, 016
SONY
THETA DIGITAL
015, 020
011
BD player Brand Code List
Brand
Code Number
SAMSUNG
000, 001, 002, 003, 004
The remote control will control Samsung BD players only.
M
53
HW-C500-C560S-XAA_0609.indd 53
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before requesting service, please check the following.
Symptom
Check
Remedy
The unit will not turn on.
• Is the power cord plugged into the
outlet?
• Connect the power plug to the
outlet.
A function does not
work when the button is
pressed.
• Is there static electricity in the air?
• Disconnect the power plug and
connect it again.
Sound is not produced.
• Are the speakers and external
components connected properly?
• Is the Mute function on?
• Connect them correctly.
• Press the MUTE button to cancel
the function.
• Is the volume set to minimum?
• Adjust the volume.
• Is the Speaker Size set incorrectly to • Refer to pages 35 to select LARGE,
NONE?
SMALL or YES.
• Connect it correctly.
Picture does not appear • Is the external component
on a TV when the
connected properly?
function is selected.
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Replace with new batteries.
• Operate at close distance.
• Check the left/right channel and connect
it/them correctly.
•
Are the left/right speaker or left/right
input/output cables connected
properly?
The sound from the left/
right channels is
reversed.
Can't receive radio
broadcasts.
• Is FM antenna connected properly?
• Connect the antenna correctly.
• If the input strength of antenna signal
is weak, install the FM antenna in a
place with good reception.
• Refer to pages 16 ~19 to connect them
properly.
• Refer to page 35 to select LARGE or
SMALL.
• Refer to pages 44 ~ 45 to select proper
Surround Mode.
There is no sound from
surround speakers.
• Are the surround speakers
connected properly?
• Is SURR (surround) incorrectly set to
NONE in the Speaker Size?
• Is surround mode set to stereo?
Can't select Dolby Pro
Logic ll mode.
• Is the input signal selected properly? • Only 2 channel signal can select
Dolby Pro Logic II mode. (ex:Dolby
Digital, PCM, 2 channel analog input
signal.)
54
HW-C500-C560S-XAA_0609.indd 54
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Check
Remedy
There is no sound when
playing a DTS encoded
DVD.
• Is Digital input selected?
• Check whether the DVD player is
properly connected and refer to
page 30 to select the digital input.
Product protection function
Heat protection
•
"
The protection function will come on if the main unit or power transformer overheats.
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after turning it off, PROTECTION mark will disappear on the
display and the unit will work properly.
If PROTECTION appears on the display, check whether the speaker terminal is shorted and then turn on
the unit.
M
ASC Error List
Error No.
VFD Message
Action
E01
E02
E03
HP CONCT
NO MIC
Disconnect the headphones.
Connect the microphone.
NOISY
Take an appropriate action to reduce the surrounding noise.
The speaker is too close to the microphone.
Check the distance between speaker and microphone.
E04
MIC LEVL
E05
E07
NO FRONT
LEVL OVR
Check if the front speaker is connected properly.
Check the position of each of speaker and microphone.
The distance between speaker and microphone exceeds the acceptable value.
Check the location of microphone and each speaker.
E08
E13
E14
DIST OVR
TIME OVR
CODE ERR
Unplug the power cable and plug it back.
Then, perform ASC again.
Unplug the power cable and plug it back.
Then, perform ASC again.
55
HW-C500-C560S-XAA_0610.indd 55
2010-06-16
4:05:59
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
SPECIFICATIONS
Power supply
120V, 60 Hz
Standby power consumption
Power consumption
0.9W
75W
Main unit
GENERAL
Weight
12.3 Ibs
Dimensions (W x H x D)
Operating temperature range
Operating humidity range
Frequency response
Usable sensitivity
S/N ratio
17.2 x 5.6 x 14.3 inches
41°F~+95°F
10%~75%
87.5~108.0MHz
12dBf
MONO/STEREO 55/55dB
MONO/STEREO 0.3/0.8%
30dB
1kHz, 75kHz Dev
20Hz~20kHz/THD = 0.9%
6 Ω 100W/CH
6 Ω 100W/CH
6 Ω 100W/CH
6 Ω 100W/CH
450mV/47kΩ
80dB
FM TUNER
Distortion
Stereo separation
Tuner output level
Rated output
Front speaker(left+right)
Center speaker
Surround speaker(left+right)
Subwoofer speaker
Input sensitivity/impedance
S/N ratio (analog input)
Separation (1kHz)
Analog input
AMPLIFIER
60dB
20Hz~20kHz( 3dB)
20Hz ~44kHz( 3dB)
Compatible 1080p
Compatible 1080p
NTSC/PAL
FREQUENCY
RESPONSE
Digital input/96kHz PCM
Input
Output
HDMI
TV format
Input level/impedance
1Vp-p/75 Ω
VIDEO OUTPUT Output level/impedance
Video frequency response
S/N ratio
1Vp-p/75 Ω
5Hz to 10kHz(-3dB)
60dB
* S/N Ratio, Distortion, Separation and Usable sensitivity are based on measurement using AES (Audio Engineering
Society) guidelines.
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
56
HW-C500-C560S-XAA_0609.indd 56
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
SAMSUNG AV receiver
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in
the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and
workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty
service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or
products if found to be defective during the limited warranty period specified above. All replaced parts and products become the
property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG's obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an
“AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent
otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including,
but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or
other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations,
repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions,
cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or
reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery
problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT
TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER°ØS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ07660-0511
HW-C500-C560S-XAA_0609.indd 57
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Area
` North America
Canada
Contact Center
Web Site
Area
Contact Center
Web Site
ꢀ
ꢀ
ch_fr/ (French)
0848 - SAMSUNG (7267864,
CHF 0.08/min)
Switzerland
Mexico
Lithuania
Latvia
8-800-77777
8000-7267
800-7267
U.S.A
` Latin America
Argentine
Estonia
0800-333-3733
` CIS
Russia
0800-124-421
4004-0000
Brazil
8-800-555-55-55
8-800-555-555
Georgia
Chile
800-SAMSUNG (726-7864)
00-1800-5077267
800-7919267
Armenia
Azerbaijan
Kazakhstan
Uzbekistan
Kyrgyzstan
Tadjikistan
0-800-05-555
Nicaragua
Honduras
Costa Rica
Ecuador
088-55-55-555
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
0-800-507-7267
1-800-10-7267
800-6225
El Salvador
Guatemala
Jamaica
1-800-299-0013
1-800-234-7267
800-7267
ua_ru
Ukraine
0-800-502-000
Panama
Puerto Rico
1-800-682-3180
Belarus
810-800-500-55-500
00-800-500-55-500
Rep. Dominica 1-800-751-2676
Trinidad &
Tobago
Moldova
` Asia Pacific
Australia
1300 362 603
Venezuela
Colombia
` Europe
0-800-100-5303
01-8000112112
New Zealand
400-810-5858
China
010-6475 1880
0810 - SAMSUNG
Austria
Belgium
Czech
(7267864, € 0.07/min)
hk
Hong Kong
(852) 3698-4698
hk_en/
be (Dutch)
be_fr (French)
02-201-24-18
3030 8282
1800 110011
India
1800 3000 8282
800 - SAMSUNG
(800-726786)
1800 266 8282
0800-112-8888
021-5699-7777
Denmark
Finland
France
70 70 19 70
Indonesia
030 - 6227 515
01 48 63 00 00
Japan
0120-327-527
1800-88-9999
Malaysia
01805 - SAMSUNG
(726-7864 € 0,14/Min)
Germany
1-800-10-SAMSUNG
(726-7864)
Hungary
Italia
1-800-3-SAMSUNG
(726-7864)
Philippines
800-SAMSUNG (726-7864)
261 03 710
1-800-8-SAMSUNG
(726-7864)
Luxemburg
02-5805777
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
Netherlands
Norway
Singapore
Thailand
1800-29-3232
02-689-3232
815-56 480
0 801 1SAMSUNG (172678)
022-607-93-33
Poland
Taiwan
0800-329-999
1 800 588 889
Vietnam
Portugal
Slovakia
` Middle East & Africa
Turkey
444 77 11
902 - 1 - SAMSUNG
(902 172 678)
Spain
South Africa
U.A.E
Sweden
U.K
800-SAMSUNG (726-7864)
8000-4726
0845 SAMSUNG (7267864)
0818 717100
Bahrain
Jordan
Eire
800-22273
HW-C500-C560S-XAA_0609.indd 58
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park,
NJ 07660-0511
1-800-SAMSUNG
(7267864)
IN THE US
Code No. AH68-02266R
HW-C500-C560S-XAA_0609.indd 59
2010-006-09
5:11:39
Download from Www.Somanuals.com. All Manuals Search And Download.
|