NETWORK CAMERA
User Manual
SNB-3002
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
English _3
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling
iCn AacUcoTrdIOanNce with the installation instructions.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
: TO REDUCE THE RISK OF ELECTRIC SHOCK.
CAUTION
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
4_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.
Please use the input power with just one camera and other devices must not
be connected.
English _5
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
Please read the following recommend safety precautions carefully.
Do not place this apparatus on an uneven surface.
Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
Reference : In case of providing information for helping of product’s usages
Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
Please read this manual for the safety before using of goods and keep it in
the safe place.
6_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
3
Important Safety Instructions
Product Features
OVERVIEW
9
9
Recomended PC Specifications
Recomended SD/SDHC Memory
Card Specifications
10
3
10
What’s Included
11
At a Glance
15
16
18
19
Mounting the Lens
INSTALLATION &
Inserting/Removing a SD Memory
Card
CONNECTION
Memory Card Information
(Not Included)
15
Connecting with other Device
22
23
Connecting the Camera Directly
to Local Area Networking
Connecting the Camera Directly
to a DHCP Based DSL/Cable
Modem
NETWORK CONNECTION
AND2SET2UP
24
25
Connecting the Camera Directly
to a PPPoE Modem
Connecting the Camera to a
Broadband Router with the
PPPoE/Cable Modem
26
27
31
32
34
34
Buttons used in IP Installer
Static IP Setup
Dynamic IP Setup
Port Range Forward (Port Mapping)
Setup
Connecting to the Camera from a
Shared Local PC
Connecting to the Camera from a
Remote PC via the Internet
English _7
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
35
36
37
38
40
43
44
Connecting to the Camera
Login
WEB VIEWER
Installing ActiveX
Installing Silverlight Runtime
Using the Live Screen
Search and play by event
Search and play by time
35
46
46
56
63
70
Setup
SETUP SCREEN
Audio & Video Setup
Network Setup
Event Setup
46
APPENDIX
System Setup
75
79
80
82
83
86
Specification
Product Overview
Troubleshooting
Open Source Announcement
License
75
GPL/LGPL Software License
8_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT FEATURES
• Multi-Streaming
This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.
• Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
• Alarm
If an event occurs, the event-related video will be transferred to the email specified by the
user, or saved to the SD memory.
• Video Motion Detection
Detects a motion from the video before triggering an event.
• Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
• ONVIF Compliance
This product supports ONVIF.
RECOMENDED PC SPECIFICATIONS
• CPU : Intel(R) Core(TM)2 2.4 GHz or higher
• Operating System : Windows XP, VISTA, 7
Mac OS
• Resolution : 1280X1024 pixels or higher
• RAM : 2GB or higher
• Web Browser : Internet Explorer 7.0 or Higher, Firefox 3.0 or Higher,
Chrome 8.0 or Higher, Safari 4.0 or Higher
Neither a beta test version unlike the version released in the company website nor the developer version will
be supported.
It is recommended to connect to IPv6 in Windows 7.
• Video Memory : 256MB or higher
If the driver of the video graphic adapter is not installed properly or is not the latest version, the
J
video may not be played properly.
For a multi-monitoring system involving at least 2 monitors, the playback performance can be
deteriorated depending on the system.
English _9
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
RECOMENDED SD/SDHC MEMORY CARD
SPECIFICATIONS
• 2GB ~ 32GB
• To ensure proper recording of video data, it is recommended you use a memory card that
supports at least read/write speed 10Mbps and Class 6.
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance
Item Name
Quantity
Description
SNB-3002
Camera
1
User Manual,
Installer S/W CD,
CMS S/W DVD
2
1
1
Quick Guide
C Mount Adapter
Used to install the camera lens
Auto Iris Lens Connector
Camera Holder (Mount)
1
2
Used to install the camera holder
Used to install the mount
Camera Holder (Mount) Screws
Lens Options (not included)
C/CS Lens
Optional lens to be inserted in a camera
10_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
AT A GLANCE
Front Side
<Fixed Bracket>
Description
SNB-3002
Item
Camera Holder
Used when you mount the camera onto the bracket by fixing the camera
a
(Mount) Holes
holder (mount) adaptor with the bracket.
Used to fix the camera on a bracket or mounting bracket.
The screw size : use this screw to fix the mounting bracket.
Mounting Bracket
Screw Hole
1/4" - 20UNC (20THREAD/1")
L : 4.5mm 0.2mm (ISO Standard), or 0.197"
(ASA Standard)
b
c
FBL Lever
Adjust the FBL (Flange-Back Length) value according to the lens.
English _11
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
Item
Description
Auto Iris Lens
Installed on the lens adaptor.
d
(Optional)
Auto Iris Lens
Used to supply power and output signal to control the iris of the lens.
e
Connector
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied
ethanol.
M
Mounting Bracket is not included.
For more information to use mounting bracket, refer to the product’s documentation.
12_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Side
AUDIO OUT AUDIO IN
SD CARD
SD SYSTEM POWER
RESET
VIDEO
NETWORK
+
1
2
3
4
5
6
1 : ALARM IN 4 : GND
2 : ALARM OUT 5 : RS-485+
3 : ALARM COM 6 : RS-485-
ACT
LINK
GND
AC 24V
DC 12V
Item
Description
SD Memory Card
Compartment for the SD memory card.
a
b
Compartment
AUDIO OUT Terminal for audio output.
Audio terminal
AUDIO IN
SD
Terminal for audio input.
ON : A memory card is inserted and operates normally.
Flashing : Failed to record, insufficient space, or inserted
abnormally.
OFF : Camera is off, camera is restarting, memory card is
not in place, or when record is off.
System, Power,
SD Indicators
c
ON : The camera is turned on and connected to the network
properly.
SYSTEM
Flashing : During DDNS setup, or in case of setup failure, or
in a state of unstable network connection.
OFF : When the system is rebooting, or turned off.
English _13
Download from Www.Somanuals.com. All Manuals Search And Download.
overview
Item
Description
ON : While the power is on
OFF : If the power is off
System, Power,
POWER
c
SD Indicators
Resets the camera settings to the default. Press and hold for about 5
seconds to reboot the system.
If you reset the camera, the network settings will be adjusted so that
J
Reset Button
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can connect
to the network.
d
Power Port
Used to plug the power cable.
Used for earth-grounding.
e
GND
f
Network Port
Used to connect a PoE or Ethernet cable.
g
ALARM IN
Used to connect the alarm input signal.
ALARM OUT Used to connect the alarm output signal.
ALARM COM Common port where the alarm output signal is connected.
I/O Port
h
GND
Used for earth-grounding.
RS-485+
RS-485-
Port used for connecting to the pan/tilt receiver.
Port used for connecting to the pan/tilt receiver.
Video Out Port
Analog video output port. (for installation)
i
The RS-485+/- ports are used to directly connect the Pan/Tilt receiver for data transfer.
J
14_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
installation & connection
MOUNTING THE LENS
Disconnect the power before proceeding.
The C lens and CS lens are not included in the product package.
M
Mounting the C lens
Turn the C mount adaptor clockwise to insert it and do the same with the C lens.
SNB-3002
C Lens
C Mount Adapter
Mounting the CS lens
Turn the optional CS lens clockwise to insert it.
SNB-3002
CS Lens
English _15
Download from Www.Somanuals.com. All Manuals Search And Download.
installation & connection
Connecting the Auto Iris Lens connector
Insert the lens connector into the corresponding hole of the camera.
SNB-3002
Focusing
Turn the lens left or right to control the zoom and focus the lens so that you can view a clear,
sharp object.
INSERTING/REMOVING A SD MEMORY CARD
Disconnect the power cable from the camera before inserting the SD memory card.
J
Inserting a SD Memory Card
Loosen the screw and open the cover of the SD memory card. Insert the SD card in the
arrow direction.
1
2
3
4
5
6
1
2
3
:
:
:
ALARM IN
ALARM OUT
ALARM COM
4
5
6
:
:
:
GND
RS-485+
RS-485-
Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
SD memory card.
J
16_ installation & connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing a SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.
1
2
3
4
5
6
1
2
3
:
:
:
ALARM IN
ALARM OUT
ALARM COM
4
5
6
:
:
:
GND
RS-485+
RS-485-
Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the
slot when released.
J
To remove the SD memory card, set <Record> to <Off> from <SD record> and press
[Apply (
)]. (page 64)
If you have saved data in the SD memory card, removing the SD memory card prior to setting
record to OFF will cause damage to the data stored in the card.
English _17
Download from Www.Somanuals.com. All Manuals Search And Download.
installation & connection
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports SD/SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
For your camera, we recommend you use a memory card from the following
manufacturers:
SD/SDHC Memory Card : Sandisk, Transcend
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
❖ Memory Card Components
Contacts
Lock Switch
SD/SDHC
18_ installation & connection
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING WITH OTHER DEVICE
AUDIO OUT AUDIO IN
SD RD
Monitor
(for installation)
SD SYSTEM POWER
RESET
VIDEO
NETWORK
+
1
2
3
4
5
6
1
2
3
:
:
:
ALARM IN
4
5
6
:
:
:
GND
RS-485+
RS-485-
ACT
LINK
GND
C 24V
C 12V
ALARM OUT
ALARM COM
Power
Ethernet
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
Be careful not to reverse the polarity when you connect the power cable.
J
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
If both PoE and DC 12V are supplied, the product will operate with the first-applied power source.
Please make sure the monitor and camera are turned off when connecting them.
English _19
Download from Www.Somanuals.com. All Manuals Search And Download.
installation & connection
Connecting to Audio Input/Output
Speaker
Microphone
PC
Microphone
Network
1
2
3
4
5
6
1
2
3
:
:
:
ALARM IN
ALARM OUT
ALARM COM
4
5
6
:
:
:
GND
RS-485+
RS-485-
Speaker
Amp
Amp Microphone
1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
3. Check the specifications for audio input.
• Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
• Full duplex Audio
• Audio in
Used for mono signal line input (Max.2.4 Vpp)
• Audio out
Used for mono signal line output (Max.2.4 Vpp)
• Line out impedance
600ꢀ
20_ installation & connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm I/O Wiring Diagram
ALARM IN
1
2
3
4
5
6
(5mA sink)
ALARM OUT
(30VDC 2A,
125VAC 0.5A MAX)
ALARM COM
GND
RS-485+
RS-485-
Connecting to the I/O port box
Connect the Alarm I/O signal to the corresponding port of the rear port box.
1
2
3
4
5
6
AUDIO OUT AUDIO IN
SD CARD
SD SYSTEM POWER
RESET
VIDEO
NETWORK
+
1
2
3
4
5
6
1 : ALARM IN 4 : GND
2 : ALARM OUT 5 : RS-485+
3 : ALARM COM 6 : RS-485-
1
2
3
: ALARM IN
4
5
6
:
:
:
GND
RS-485+
RS-485-
ACT
LINK
GND
AC 24V
DC 12V
: ALARM OUT
: ALARM COM
• ALARM IN : Used to connect the alarm input signal.
• ALARM OUT : Used to connect the alarm output signal.
• ALARM COM : Common port where the alarm output signal is connected.
• GND : Used for earth-grounding.
• RS-485+ : Communication port for RS-485 receiver (+).
• RS-485- : Communication port for RS-485 receiver (–).
Connecting an external RS-485 device
Connect the camera with an external device using the [RS-485 +, -] ports.
You can control the pan/tilt operations of the camera via RS-485 communications.
The GND connection is recommended for RS-485 communications. If you encounter a communication
failure, connect the GND pin as appropriate to correct the GND level between camera and external device.
English _21
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
SNB-3002
Camera
SNB-3002
INTERNET
Switch
Camera
External Remote PC
Firewall
DDNS Server
(Data Center, KOREA)
Local PC
<Local Network>
A remote PC in an external Internet out of the LAN network may not be able to connect to the
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
M
By factory default, the IP address will be assigned from the DHCP server automatically. If there is
no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 27)
22_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE CAMERA DIRECTLY TO A DHCP
BASED DSL/CABLE MODEM
SNB-3002
INTERNET
DSL/Cable
Modem
External Remote PC
Camera
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the camera.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
For registering the DDNS settings, refer to “Registering with DDNS”. (page 58)
M
For configuring the DDNS settings, refer to “DDNS”. (page 57)
For setting the network type, refer to “Interface”. (page 56)
English _23
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
CONNECTING THE CAMERA DIRECTLY TO A PPPoE
MODEM
SNB-3002
INTERNET
PPPoE Modem
External Remote PC
Camera
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the camera.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [PPPoE].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
For registering the DDNS settings, refer to “Registering with DDNS”. (page 58)
M
For configuring the DDNS settings, refer to “DDNS”. (page 57)
For setting the network type, refer to “Interface”. (page 56)
24_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE CAMERA TO A BROADBAND ROUTER
WITH THE PPPoE/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
SNB-3002
Camera
SNB-3002
INTERNET
PPPoE or
PPPoE or
Broadband
Router
Cable Modem
Cable Modem
Camera
External Remote PC
DDNS Server
(Data Center, KOREA)
Local PC
Configuring the network settings of the local PC connected to a
Broadband Router
Configuring the network settings of the local PC connected to a Broadband Router, follow
the instructions below.
• Select : <Network Neighborhood> <Properties> <Local Area Connection>
<Properties> <General> <Internet Protocol (TCP/IP)> <Properties>
<Obtain an IP address automatically> or <Use the following IP address>.
• Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1
IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
For the address of the Broadband Router, refer to the product’s documentation.
M
For more information about port forwarding of the broadband router, refer to “Port Range
Forward (Port Mapping) Setup”. (Page 32)
Download from Www.Somanuals.com. All Manuals Search And Download.
English _25
network connection and setup
BUTTONS USED IN IP INSTALLER
Item
Description
Model name of the connected camera.
Device Name
Click the column to sort the list by model name.
a
However, search will be stopped if clicked during the search.
Alias
This function is not currently implemented.
b
c
Displays either <Static> or <Dynamic> for the current network connection
Mode
status.
Ethernet address for the connected camera.
MAC(Ethernet)
Address
Click the column to sort the list by Ethernet address.
d
e
f
However, search will be stopped if clicked during the search.
It is an IP address specified in the camera.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
The factory default is “192.168.1.100”.
IP Address
Protocol
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
26_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if
DDNS registration has failed.
URL
g
IPv4
IPv6
Scans for cameras with the IPv4 setting.
h
i
Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment.
Scans for cameras that are currently connected to the network.
Search
j
k
l
m
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
Auto Set
Manual Set
Exit
The IP Installer automatically configures the network settings.
You should configure the network settings manually.
Exits the IP Installer program.
For the IP installer, use only the installer version provided in the installation CD or use the
latest one if available. You can download the latest version from the Samsung web site (www.
samsungipolis.com).
M
STATIC IP SETUP
Manual Network Setup
Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
M
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
The default values of <IP Address>,
<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will
be displayed.
English _27
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
3. In the <Address> pane, provide the
necessary information.
• MAC (Ethernet) Address : The MAC
(Ethernet) address of the applicable
camera will be set automatically so
you don't need to input it manually.
You can configure the static IP settings
M
only if the DHCP checkbox is unchecked.
If not using a Broadband Router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.
4. In the <Port> pane, provide
necessary information.
• HTTP Port : Used to access the
camera using the Internet browser,
defaulted to 80. Use the spin button
to change the HTTP Port value.
• VNP Port : Used to control the video
signal transfer, defaulted to 4520.
5. Enter the password.
This is the login password for the “admin” user who accesses the camera.
The default password is “4321”.
The default password can be exposed to a hacking thread so it is recommended to change the
J
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
6. Click [OK].
Manual network setup will be completed.
28_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
If using a Broadband Router
• IP Address : Enter an address falling in
the IP range provided by the Broadband
Router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254
• Subnet Mask : The <Subnet Mask>
of the Broadband Router will be the
<Subnet Mask> of the camera.
• Gateway : The <Local IP Address> of
the Broadband Router will be the <Gateway> of the camera.
The settings may differ depending on the connected Broadband Router model.
M
For more information, refer to the user manual of the applicable router.
For more information about port forwarding of the broadband router, refer to “Port Range
Forward (Port Mapping) Setup”. (Page 32)
If the Broadband Router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
Category
Camera #1
Camera #2
IP Address
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
IP related settings
Subnet Mask
Gateway
HTTP Port
VNP Port
8080
4520
8081
4521
Port related settings
If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar
of the Internet browser before you can access the camera.
M
English _29
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
Auto Network Setup
Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
M
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>,
and <Gateway> will be set automatically.
3. Enter the password.
This is the login password for the
“admin” user who accesses the
camera. The default password is
“4321”.
The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related issues
caused by the unchanged password shall be
responsible for the user.
4. Click [OK].
Auto network setup will be completed.
30_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
DYNAMIC IP SETUP
Dynamic IP Environment Setup
• Example of the Dynamic IP environment
- If a Broadband Router, with cameras connected, is assigned an IP address by the
DHCP server
- If connecting the camera directly to modem using the DHCP protocols
- If IPs are assigned by the internal DHCP server via the LAN
Checking the Dynamic IP
1. Run the IP Installer on the user’s local
machine to display cameras allocated
with <Dynamic IP> addresses in the
list.
2. Select a camera in the list, and click
[Manual Set] to check the <Dynamic
IP> of the camera.
If you uncheck <DHCP>, you can
change IP to <Static>.
English _31
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed a Broadband Router with a camera connected, you must set the port range
forwarding on the Broadband Router so that a remote PC can access the camera in it.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband
Router, select <Applications &
Gaming> - <Port Range Forward>.
For setting the port range forward for
a third-party Broadband Router, refer
to the user guide of that Broadband
Router.
2. Select <TCP> and <UDP Port>
for each connected camera to the
Broadband Router.
Each port number for the Broadband
Router should match that specified in
<Network> - <Port> from the
camera's Setup menu.
3. When done, click [Save Settings].
Your settings will be saved.
Above sample instructions are based on the CISCO’s Broadband Router (Model: LINKSYS).
M
The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
32_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up Port Range Forward for several network cameras
When several network cameras are connected to one Broadband Router device, you
should forward the TCP 943 port of the router to the TCP 943 port of a connected camera.
If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the
J
web page of the camera.
• TCP 943 port is a port for the Silverlight policy server of a camera.
• You can set a rule of Port Forwarding on the Broadband Router device through its
configuration web page.
• You cannot change the Silverlight policy server port of a camera.
• You can change the ports of the camera except the policy server port through its
configuration web pages.
When Camera1 and Camera2 are connected to a router :
User
Internet
Ù
Ú
Camera1 (192.168.1.100)
Web Server Port
VNP Port
8080
4520
3000
943
Broadband Router
Start
End
943
Protocol
IP Address
Ù
Ù
RTSP Port
943
TCP
192.168.1.100
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
Policy Server Port
3000
3001
4520
4521
8080
8081
3000
3001
4520
4521
8080
8081
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
Camera2 (192.168.1.101)
Web Server Port
VNP Port
8081
4521
3001
943
RTSP Port
Policy Server Port
English _33
Download from Www.Somanuals.com. All Manuals Search And Download.
network connection and setup
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC
1. Run the IP Installer.
It will scan for connected cameras and
display them as a list.
2. Double-click a camera to access.
The Internet browser starts and
connects to the camera.
Access to the camera can also be gained by typing the camera's IP address in the address bar of
M
the Internet browser.
CONNECTING TO THE CAMERA FROM A REMOTE PC VIA
THE INTERNET
Since using the IP Installer on a remote computer that is not in the Broadband Router’s network
cluster is not allowed, users can access cameras within a Broadband Router’s network by using
the camera’s DDNS URL.
1. Before you can access a camera in the Broadband Router network, you should have
set the port range forward for the Broadband Router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address
of the camera, or the IP address of the Broadband Router in the address bar.
34_ network connection and setup
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
CONNECTING TO THE CAMERA
Normally, you would
1. Launch the Internet browser.
2. Type the IP address of the camera in
the address bar.
ex) • IP address (IPv4) : 192.168.1.100
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd:
ffff:0000:0000:ffff:1111
:0000:ffff:1111] - the Login dialog
should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080)
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
- the Login dialog should appear.
English _35
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
To check the DDNS address
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE
modem, the IP address of your network will be changed each time you try to connect to
the ISP (Internet Service Provider) server.
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check
the changed IP when you try to access the device.
your device, and set the DDNS option to <Samsung DDNS> before providing the host
name for the DDNS server.
LOGIN
The default user ID is “admin”, and the default password is “4321”.
1. Enter “admin” in the <User Name>
input box.
2. Enter “4321” in the <Password> input
box.
If the password is changed, enter the
changed password instead.
3. Click [OK].
If you have logged in successfully, you
will the Live Viewer screen.
For security purposes, ensure that you
M
change the password in <System> -
<User>.
The administrator ID, “admin”, is fixed and can not be changed.
The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
If you check the “Remember my password” option when your input is done, in future you will be
logged in automatically without being prompted to enter the login information.
You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut
J
the image on the borders.
36_ web viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING ACTIVEX
If connecting to a camera for the first time, you will see the installation message. Then, install the
required ActiveX to access the camera and control the video from it in real time.
1. When accessing the start screen of
the monitoring page, click the yellow
warning message in the top of the
page.
2. Click <Install This Add-on for All
users on This Computer...>.
3. The security warning popup appears,
click [Install].
4. When the required ActiveX is installed
properly after your access to the
camera, the Live screen should appear.
English _37
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
INSTALLING SILVERLIGHT RUNTIME
If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will
be redirected to the Silverlight Runtime installation page automatically when accessing the web
viewer.
1. Click <Click Here>.
2. When the file download dialog pops up,
click <Run>.
3. When the download is completed, click
<Run>.
4. The Silverlight Runtime installation page
will be displayed. <Install now> to
proceed with the installation.
38_ web viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. When done, click <Close>.
6. Close and restart the web browser, and
try to access the Web Viewer.
When Silverlight Runtime is properly
installed, you will see the Live screen.
For normal installation, set the Block
J
Popup setting as follows:
ex) Internet Explorer Tools Block
Popup Turn Off Pop-up Blocker (B)
However, MAC OS X users who are not connected to the Internet can use the provided installation
CD to install Silverlight Runtime (Run the executable “Silverlight_xxx.dmg” in the CD. You will be
guided through installation of the software).
English _39
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
USING THE LIVE SCREEN
Item
Description
Monitoring
Playback
Setup
Move to the monitoring screen.
a
b
c
d
e
f
Switch to the monitoring screen that plays recording data in the SD memory.
Move to the Setup screen.
Viewer Screen
Alarm Output
Audio
Displays the Live video on the screen.
Activate the Alarm Out port.
Display the audio Listen and Talk toggle button on the screen.
Hides the alarm indicator near the border of the viewer screen.
In the following cases, the alarm message will pop up on the border of the
viewer.
Hide the alarm
indicator
g
If an event (alarm, motion detection) occurs
-
If the camera is turned off
-
-
If the network is disconnected
40_ web viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Control the pan/tilt/zoom operations of the camera.
PTZ
The pan/tilt/zoom operations will be enabled only if the camera is connected to
h
i
j
k
a pan/tilt-compliant receiver.
Digital zoom
You can use the mouse wheel to activate the digital zooming.
Screen
Adjust the screen to the optimal size, and display the Full Screen icon on the Live
screen.
Optimization,
Full Screen
Capture
Saves the snapshot as an image file in the .bmp or .jpg format.
You can select a profile type in <Video profile> under the <Audio & Video> setup
menu.
Video Format
l
If the “Invalid codec” message is displayed, select a profile type from the profile
M
list again.
Web pages related to playback and setting menus are accessible only by the admin. For other
user accounts, the buttons will be deactivated.
M
To capture the snapshot
1. Click [
] on the scene to capture.
The Capture dialog should appear.
2. Click [Save] button.
The screenshot will be saved in the
specified path.
If you encounter an interrupted video
M
when capturing the image with IE8 on a
Windows 7-based PC, deselect “Turn On
Protected Mode” from “Tools – Internet
Options – Security”.
English _41
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
To toggle the audio sound
1. Click the [Audio (
)] button.
The corresponding button will be
displayed in the Viewer.
2. Click the button to listen to / mute the
sound as you wish.
This button operates as a toggle
button.
To toggle the microphone sound
1. Click the [Mic (
displayed in the Viewer.
)] button.
The corresponding button will be
“Any available audio capture device
there is no Microphone.
J
cannot be found!” message appears if
2. Click the button to start / stop talking.
This button operates as a toggle button.
The Silverlight permission dialog appears when you click the microphone button.
As the AUDIO and MIC buttons (
,
) are simply to display or hide the toggle button on
J
the viewer screen, you cannot control the actual operations of those buttons.
So if you want to adjust the microphone or audio settings, use the toggle button on the viewer
screen.
To fit the full screen
1. Click the [Full Screen (
)] button.
The corresponding button will be displayed in the Viewer.
2. Click the button.
This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
For the ActiveX viewer, you can just click an appropriate button on the page to perform the
M
operation as the audio I/O buttons and the Full Screen button are not displayed in the top of the
screen.
42_ web viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
To control the PTZ
1. Press the [PTZ (
)] button.
2. When the PTZ button bar appears on
the screen, use the direction buttons to
adjust the camera angle, zoom factor
or focus to your preference.
For further details on PTZ use, refer to
M
“External PTZ setup”. (page 54)
SEARCH AND PLAY BY EVENT
1. Click the [Playback (
)] button.
2. Specify the start time and end time of
your search.
3. Select an event type for your search
within the specified period.
4. Click the [Search (
)] button.
The search results will be displayed in
the list.
If more than 500 events are recorded
M
within the search period, your search will
be limited up to the date when the 500th event is recorded.
For instance, if the search period is between 10th and 15th day of the month, and more than 500
events were recorded 10th through 11th, your search will be limited up to 11th day with a total of
500 events, and events after then (from 12th) will not be found.
5. Select a data item to play in the search
list.
6. Click the [Play (
)] button.
7. To stop playing the video, click [Stop
(
)].
To return to the search screen, click
[Exit (
)].
English _43
Download from Www.Somanuals.com. All Manuals Search And Download.
web viewer
SEARCH AND PLAY BY TIME
1. Click [Search by Time (
)].
2. Click a desired date in the calendar.
The video on the specified date will be
played.
3. If the video playback is stopped, select
a time and click [Play (
)] to play the
video for the selected time.
While the video is being played, the
recording time for the current video will
be shown.
4. Search for the video forward or backward, and control the play speed.
If the video is being played, the button will switch to [
,
,
,
,
,
,
,
]
with the information of the playback direction and speed.
-
To control the play speed
If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will
increase accordingly.
If selecting (, the button will switch to x8, x4, x2, x1, and the play speed will
decrease accordingly.
-
To control the playback direction
If you see the ) button with the play speed displayed, the video will be played
forward; Whereas, if you see the ( button with the play speed displayed, the video
will be played backward.
5. Move [Time bar (
)] to a desired time point of the video before playing it.
The time containing a normal recoding file will be highlighted in blue; the time with
the event recording will be highlighted in red.
The time search is not available with other web browsers than Internet Explorer.
J
To check time information of the playing video
1. Click the [About (
)] button.
2. Date and time information appears on the screen.
44_ web viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
To back up the searched video
1. During playback, click [
scene to back up.
] on the
Save as window appears.
2. Click [Save].
The screenshot will be backed up to
the specified path.
To play the backup video
The backup video will be saved in .avi format. The backup video can be played with any
media player supporting the format on your PC.
English _45
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
SETUP
You can configure the audio & video, network, event and system settings of the camera via the
network.
1. In the Live screen, click [Setup (
)].
2. The Setup screen appears.
AUDIO & VIDEO SETUP
Video profile
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Video profile>.
3. Select a <Video profile> number.
4. Click the input box of each item and
enter / select a desired value.
The context menu may differ depending on
the selected codec type.
• Default profile : This is the default
video profile.
• E-mail/FTP profile : Video profile to
be transferred to the specified email
or FTP site.
Only the MJPEG codec can be set as the
E-mail/FTP profile.
• Record profile : This is the profile that is applied to video recording.
5. When done, click [Apply (
)].
MPEG-4 videos can not be stored in the SD memory.
M
46_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
To add a video profile
You can add as many codecs as necessary so that a variety of profiles can be applied
according to the recording condition.
1. Select a profile number.
2. Provide the name and select a codec.
3. Specify the conditions under which the codec will be applied.
4. Specify the details of the selected codec including resolution and frame rate.
• Resolution : Set the video size of the MPEG-4, H.264 and MJPEG files.
• Framerate : Specify the frame rate.
• Compression : Specify the compression rate of the video.
• Maximum bitrate : Specify the maximum bit rate of the video.
As the bit rate can be adjusted limitedly according to the resolution, frame rate and screen
J
complexity, the actual bit rate can be greater than the maximum bit rate. So you must
consider the use conditions when setting the value.
• Bitrate control : You can select one from constant bit rate and variable bit rate for
compression. Constant bit rate (CBR) varies the video quality and fixes network
transfer bit rate, while variable bit rate emphasizes the quality by varying network
transfer bit rate.
• Target bitrate : Specify the bit rate at which you will transfer the video.
• Encoding priority : You can set the video transfer method to Framerate or
Compression.
• GOP size : Select a GOP size between 1 and 15.
• Profile : You can select the H.264 profiling method.
• Entropy coding : Reduce the possible compression loss due to encoding.
• Multicast(SVNP) : Specify the use of the SVNP protocol.
- IPv4 : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : Set the TTL for the SVNP packet.
• Multicast(RTP) : Specify the use of the RTP protocol.
- IPv4 : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : You can set the TTL for the RTP packet.
English _47
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
What is GOP size?
GOP (Group of Pictures) is a set of video frames for MPEG-4 and H.264 format
compression, indicating a collection of frames from the initial I-Frame (key frame) to the next
I-Frame. GOP consists of 2 kinds of frames: I-Frame and P-Frame.
I-Frame is the basic frame for the compression, also known as Key Frame, which contains
one complete image data. P-Frame contains only the data that has changed from the
preceding I-Frame.
You can set between 1 and 15 for the MPEG-4 and H.264 CODEC.
Video setup
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Video setup>.
3. Select a <Video source> mode.
• Flip mode : Turn upside down
the image that is captured by the
camera.
• Mirror mode : Flip horizontal the
image that is captured by the
camera.
4. Specify the privacy zone.
5. When done, click [Apply (
)].
48_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the privacy zone
You can specify a certain area of the camera video to be protected for your privacy.
1. Set it to <On>.
2. Specify the <Color> that will fill the
privacy area.
3. When done, click [Apply (
)].
4. On the video screen, click a vertex of
the selected area to display the dialog
as shown.
5. Enter the name of the set privacy area
and press [OK].
6. If you want to delete an area, select that area in the list and press [Delete (
)].
Audio setup
You can configure the I/O settings of the audio source from the camera.
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Audio setup>.
3. Adjust the audio I/O levels to your
preference.
• Audio-In : You can set the use of
audio input and specify the input
value.
• Audio-Out : You can set the use of
audio output and specify the output
value.
4. When done, click [Apply (
)].
English _49
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Camera setup
You can change the camera settings according to the environment where the camera is
located.
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Camera setup>.
3. Configure the settings as necessary
of : SSDR, White balance, Backlight,
Exposure, Special, OSD, Time OSD
4. When done, click [Apply (
)].
)] button
If a certain time (timeout: 240s) is elapsed with
your not pressing the [Apply (
after changing the settings, your changes will
not be applied.
SSDR (Samsung Super Dynamic Range) Setup
In a scene where the difference between bright and dark is severe, you can increase the
brightness of the dark area alone to regulate the overall brightness.
1. Select <SSDR>.
2. Set <Mode> to <On>.
3. Configure the <Level> settings as
necessary.
• Level : Adjust the level of the dynamic range.
White balance Setup
You can correct the image colors based on white under any lighting conditions.
1. Select <White balance>.
2. Select <Mode>.
• ATW1/ATW2 : Corrects the colors of
the camera video automatically.
• Manual : You can adjust the red and
blue gains of the camera video manually.
50_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
• AWC : Corrects the colors of the camera video to be optimized to the current
lighting condition and screen mode.
You may need readjustment if the lighting condition is changed.
• 3200K : Set the color temperature to 3200K.
• 5600K : Set the color temperature to 5600K.
In AWC mode, click the [AWC Set] button if you want to keep the white balance level of the
M
current image.
BLC Setup
You can specify a desired area on the video manually and set the area to be displayed
more clearly.
1. Select <Backlight>.
2. Set <Mode> to <BLC>.
3. Set the <Top, Bottom, Left, Right>
levels to specify the target area.
WDR Setup
You can set to display a sharp image of the objects in a scene where both bright and dark
areas exist.
1. Select <Backlight>.
2. Set <Mode> to <WDR>.
3. Specify the <WDR level> and <WDR
Limit>.
If WDR mode is active, the shutter mode
M
cannot be changed. Data transfer via the
network is available at up to 15 fps.
If the WDR mode is active, a moving
object can cause an afterimage on the screen.
English _51
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Exposure Setup
You can adjust the exposure level of the camera.
1. Select <Exposure>.
2. Select each item and set it properly.
• Brightness : Adjust the screen
brightness.
• Shutter mode : Adjust the electronic
shutter of the camera.
- ESC (Electronic shutter control) :
Adjust the shutter speed
automatically according to the
ambient brightness.
- Manual : Adjust the shutter speed of the camera manually.
- A.FLK (Anti flicker) : Select this feature if you encounter a flickering screen due
to a frequency mismatch with the ambient lighting.
• Shutter speed : Control the shutter speed manually.
• SSNR3 : Specify the use of noise reduction.
• SSNR3 level : Adjust the noise reduction level.
• Sens-up mode : Automatically senses the darkness level at night or in a low
contrast scene and extends the accumulation time accordingly for a bright and
sharp image.
If you set the shutter mode to Manual/A.FLK, SENS-UP mode will be deactivated.
The greater the Sens-Up factor is, the brighter the screen becomes but it may result in an
afterimage or video delay.
• Sens-up limit : Set the work condition to Auto mode in a low contrast scene.
• Lens : Select to set the lens mode of the camera to Manual or Auto.
- DC(Auto) : Select this if you use the DC lens. Only the iris is adjusted
automatically, but the focus is not controlled automatically.
- Manual : Select this if you use a lens on which you adjust the iris and focus
manually.
- Video(Auto) : Select this if you use the video-dedicated lens.
• AGC mode : Select AGC Control mode.
Adjust the gain value of the video (that, in particular, was recorded at a low
contrast scene and had a lower brightness level than normal) to control the video
brightness.
52_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Setup
1. Select <Special>.
2. Select each item and set it properly.
• DIS : Automatically compensates for
the flicker on the screen.
• Day & night : You can switch the
mode to adjust the black and white
level as well as the colors.
- Color : Always displays the video in
colors.
- B/W : Always displays the video in
black and white.
- Auto : Displays in color mode during normal daytime and switches to black and
white mode in a low contrast scene at night.
\
Dwell time (Color -> B/W) : If you set Day & night mode to <Auto>, specify the time
duration the brightness is kept in order to properly perform the mode switch from
Color to B/W.
\
\
Brightness (Color -> B/W) : If you set Day & night mode to <Auto>, specify the level
of brightness where the mode can be switched from Color to B/W.
Dwell time (B/W -> Color) : If you set Day & night mode to <Auto>, specify the time
duration the brightness is kept in order to properly perform the mode switch from
B/W to Color.
\
Brightness (B/W -> Color) : If you set Day & night mode to <Auto>, specify the level
of brightness where the mode can be switched from B/W to Color.
If you set the AGC mode to OFF from <Exposure>, the AUTO DAY/NIGHT mode will be disabled
accordingly.
- External B/W : Control the image modes of Color and B/W when an external IR
is synchronized via the Alarm In port.
• Sharpness mode : Adjust the overall sharpness of the image.
If selecting <On>, you can adjust the sharpness of the image.
• Sharpness level : The higher the level is, the sharper and clearer the outline of the
image becomes.
• Alarm in : Set the image to Color or B/W depending on the Open/Close state of
the alarm sensor.
If the Day & Night mode is set to External B/W, the alarm-in function of the event-alarm input page
will be disabled.
• Negative mode : Display the reverse image of the video.
English _53
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
OSD Setup
1. Select <OSD>.
2. Select each item and set it properly.
• Camera title : Specify the camera title
that will be displayed on the screen.
You can enter up to 15 characters for the
title.
• Camera title position x, y : Specify the coordinates where the camera title is
displayed.
Time OSD Setup
1. Select <Time OSD>.
2. Select each item and set it properly.
• Time display : Specify the use of time
display on the screen.
• Date format : Specify the date format
that will be displayed on the screen.
• Time position display X, Y : Specify the position of time.
• Display weekday : Specify whether displays the day of the week on the screen.
External PTZ setup
Configure the connection settings to the external pan/tilt receiver so that you can control
the PTZ operations via the receiver connected to the RS-485 port of the camera.
1. Select the <Audio & Video (
)> tab
from Setup menu.
2. Click <External PTZ setup>.
3. Specify the serial port.
You can set the RS-485 communication
mode for pan/tilt-compliant receiver that
is connected to the network camera.
• Protocol : From SAMSUNG-T/
SAMSUNG-E / PELCO-D/PELCO-P
/ SUNGJIN, select the same protocol
as that of the receiver.
• Camera ID : Provide a camera ID.
• Baud rate : Transfer rate for RS-485
communications
• Data : Specify the data bit.
• Parity : Specify the parity bit.
• Stop bit : Specify the stop bit.
54_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When done, click [Apply (
M
)].
All these operations above mentioned will be enabled only if the network camera is properly
connected to the pan/tilt-compliant receiver. And the serial port for the pan/tilt operations should
be properly specified.
The baud rate may not be controlled depending on the product specifications.
J
5. Click [Direction Adjustment (
)].
• [Change direction to (
)/(
)/(
)/(
)] : Change the direction of camera
lens.
•
[Moving speed control (
)] : The bigger the number is, the faster the
moving speed becomes.
6. Set the zoom and focus control
buttons.
• [Zoom In (
)] : Zooms in the
)] : Zooms out the
screen.
• [Zoom Out (
screen.
• [Adjust Focus (
/
)] : Adjusts
the focus in the screen.
• [Zoom Speed Control (
)]
: The bigger the number is, the faster
the zoom speed becomes.
7. Set the preset.
The pan/tilt/zoom operations can be controlled only if the camera is connected to a pan/tilt
M
receiver with a proper <Serial Setup>.
To add a preset
1) Select the preset number to add.
2) Set the name for the preset.
3) Press the [
] button.
To delete a preset
1) Select the preset number to delete.
2) Press the [
] button.
To move a preset
1) Select a preset number that you want to move.
2) Press the [
] button.
English _55
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
NETWORK SETUP
Interface
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <Interface>.
3. Set the <Interface> and <IPv6 setup>
as necessary.
• IP type : Select an IP connection type.
- Manual : Specify the IP address,
Subnet mask, Gateway, DNS1,
and DNS2.
- DHCP : Specify the DNS1 and
DNS2.
- PPPoE : Specify the DNS1, DNS2,
Name and Password.
If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
• MAC address : Shows the MAC address.
• IP address : Displays the current IP address.
• Subnet mask : Displays the <Subnet mask> for the set IP.
• Gateway : Displays the <Gateway> for the set IP.
• DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
• IPv6 use : Specify the use of IPv6.
• Default IPv6 Address : Obtains the IPv6 address to access the IPv6 network.
- Use Default Address Only : Use only the default IPv6 address.
- Obtain IP address via DHCP : Display and use the IPv6 address obtained from
the DHCP server.
- Use the following IP Address : Enter an IP address manually and use it.
4. When done, click [Apply (
)].
The IP addressing system will be defaulted to DHCP.
J
If no DHCP server is found, the previous settings will be restored automatically.
56_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Port
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <Port>.
3. Type in each item in the Port menu as
necessary.
Neither the port range between 0 and 1023
nor port 3702 is available.
• HTTP port : HTTP port used to
access the camera via the web
browser.
The default is 80(TCP).
• VNP port : Set a port used to transfer video signals with the Samsung protocols.
• RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
• Viewer port : Used to transfer videos to the Web Viewer; the default is 4520.
• Silverlight policy port : Silverlight is used to permit to acquire a network
connection; the default is 943.
The port range of the Viewer is between 4502 and 4534. If the VNP port is with this effective range,
the Viewer port should be specified the same as the VNP port.
You cannot change the Viewer/Silverlight policy port of a camera.
4. When done, click [Apply (
)].
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of
a camera into a general Host Name so that the user can easily remember it.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <DDNS>.
3. Select <DDNS> that you want to use.
4. Type in the DDNS items according to
the selected type.
• Samsung DDNS : Select this if you
use the DDNS server provided by
Samsung Techwin.
English _57
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
• Public DDNS : Select one of provided public DDNS servers when you use a public
DDNS server.
- Host name : Enter the name of the host (i.e., host name of Dyndns) that is
registered with the DDNS server.
- User name : Enter the user name for the DDNS service. (i.e., user ID that is
registered with Dyndns)
- Password : Enter the password for the DDNS service. (i.e., password that is
registered with Dyndns)
5. When done, click [Apply (
)].
Registering with DDNS
To register your product with the Samsung DDNS
1. Visit the iPOLiS web site(www.
samsungipolis.com) and sign in with a
registered account.
2. From the top menu bar, select <DDNS
SERVICE> - <MY DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product ID.
You must perform the duplicate check for the
ID that you entered.
58_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select a <CLASSIFICATION> and
specify the <MODEL NUMBER>.
6. Specify the product location with a
description if necessary.
7. Click [REGISTRATION].
The product will be added to the
product list that you can check.
To connect to the Samsung DDNS in camera setup
1. From the DDNS setup page, set
<DDNS> to <Samsung DDNS>.
2. Provide the <Host name> that you
registered product ID with the DDNS
site.
3. Click [Apply (
)].
When the connection is successfully
made, you will see the message of
<(Success)> on the screen.
Configuring public DDNS in Camera Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
3. Click [Apply (
)] button.
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply (
)].
English _59
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <IP filtering>.
3. Select <Filtering type>.
• Deny : If selecting this, access from
those IPs that are added to the
filtering will be restricted.
• Allow : If selecting this, access from
only those IPs that are added to the
filtering will be accepted.
4. Provide the IP that you want to grant or
deny access from.
For IPv4, the default IP address is
0.0.0.0, and the default prefix is 32.
5. Select desired IP address to be approved or rejected from the entered IP addresses.
Only the selected IPs are filtered out.
6. When done, click [Apply (
)].
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <SSL>.
3. Select a secure connection system.
To access the camera using HTTPS mode, you
have to type the IP address for the camera in
the form of “https://<Camera_IP>”.
4. Search for the public certificate that you
want to install on the camera.
To install the certificate on the camera, you need to provide a certificate name (it
can be arbitrarily assigned by the user), certificate file issued from the certification
authority and a key file.
The <HTTPS (Secure connection mode using the public certificate)> item will be active only if
there exists a public certificate installed.
5. When done, click [Apply (
)].
60_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the certificate
1. Enter the certificate name.
2. Select the certificate file to be installed and certificate key, and click [Install (
)]
button.
Deleting the certificate
1. Click [Delete (
)] button.
2. To delete a public certificate, you should access the network video decoder in
the mode of <HTTP (Do not use secure connection)> or <HTTPS (Secure
Connection mode using a unique certificate)>.
802.1x
When connecting network, you can choose whether using 802.1x protocol, and then install
the certification.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <802.1x>.
3. Set the <IEEE 802.1x Setting(EAPOL
using EAP-TLS)>.
• Enable IEEE 802.1x : Specify the use
of the 802.1x protocol.
• EAPOL Version : Select version 1 or 2.
• EAPOL ID : Enter the EAPOL ID.
• EAPOL Password : Enter the EAPOL password.
If the connected network device does not support the 802.1x protocol, the protocol will not
J
operate properly even if you set it.
To install/remove 802.1x related certificates
1. Press the [Browse (
)] button for each item and select a certificate to install.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected
item.
3. Press the [Install (
)] button to start installation with a message of “Installed”
next to the item.
4. Press the [Delete (
)] button to remove the certificate.
English _61
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <QoS>.
3. Provide the IP address.
The default prefix is 32. For DSCP, the
default is set to 63.
4. Select an IP address to which you will
apply QoS.
Only the selected IPs can be prioritized.
5. When done, click [Apply (
)].
SNMP
With the SNMP protocols, you can allow the system or network admin to monitor the
network devices on a remote site, and configure the environment settings.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <SNMP>.
3. Specify the <SNMP>.
• Enable SNMP v1 : SNMP version 1
will be active.
• Enable SNMP v2c : SNMP version 2
will be active.
-
Read Community : Provide the
name of the read community where you can access to the SNMP information.
The default name is “pubic”.
-
Write Community : Provide the name of the write community where you can
access to the SNMP information. The default name is “write”.
62_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
• Enable SNMP v3 : SNMP version 3 will be active.
-
Password : Specify the default password for SNMP version 3. The default
password is “admin4321”.
The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
4. When done, click [Apply (
)].
SNMP v3 is only able to be set when the secure connection mode is HTTPS.
J
EVENT SETUP
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images
stored in the camera to your PC if an event occurs.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or
<E-mail configuration> and enter /
select a desired value.
• FTP configuration
- Server address : Enter the IP
address of the FTP server that you
transfer the alarm images to.
- User ID : Enter the user ID with
which you will log in to the FTP
server.
- Password : Enter the user account password for logging into the FTP server.
- Upload directory : Specify the FTP path where you will transfer the alarm
images.
- Port : The default port of the FTP server is 21; however, you can use a different
port number according to the FTP server settings.
- Passive mode : Select <On> if you need to connect in passive mode due to the
firewall or the FTP server settings.
English _63
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
• E-mail configuration
- Use SSL : Specify the use of SSL.
- Server address : Enter the IP address of the email server that you use for the
email transfer.
- Use authentication : Select whether to use authorization.
- User ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different
port number according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is
incorrect, the email from the sender may be classified as SPAM by the email
server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm images to the email
that you are preparing.
4. When done, click [Apply (
)].
SD record
You can set the record conditions or the use of recording for the SD memory, check the
size of stored data, or format the SD memory itself.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <SD record>.
64_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
To make recording on the SD memory
1. Check the <Total size> and the <Free size>.
2. If the SD memory has a sufficient free space, set <Record> to <On>.
Otherwise, check the stored data and if you find them not important, then click
<Format> to format the SD memory.
If your SD memory card writes slowly, only one frame per second will be stored.
For a SD memory card with a large capacity, the formatting will be slowed down accordingly.
If the size of data grows with time, only 1 fps can be stored even if you set the record quality to Full
Frame.
3. Specify the record conditions.
• Record profile : Display the number of profile to record.
• Overwrite : If the SD memory is full, this will delete old data and store new data in
replacement.
• Pre-alarm duration : Specify the time point before the occurrence of the alarm;
starting from the time point, the images will be transferred. You can specify up to
5 seconds before the occurrence of the alarm.
• Post-alarm duration : Specify the time point after the occurrence of the alarm; to
the specified time point, the images will be transferred. You can specify up to 120
seconds after the occurrence of the alarm.
• Normal : Make recording at a certain frame rate.
• Event : Set the recording type for a certain event that occurs.
4. Specify the <Activation time>.
• Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
If set to Always, the activation time cannot be changed.
• Only scheduled time : Check if an alarm occurs at a specified day of the week for
• [
a specified time period. It activates in operated mode when the alarm occurs.
] : Reset all settings.
5. When done, click [Apply (
)].
English _65
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Alarm input
You can set the alarm input type, activation time, and operation mode.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Alarm input>.
3. Specify an input device.
• Type
- Normal Open : It is normally open,
but if it is closed, an alarm will be
triggered.
- Normal Close : It is normally
closed, but if it is open, an alarm
will be triggered.
4. Specify the <Activation time>.
• Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
If set to Always, the activation time cannot be changed.
• Only scheduled time : Check if an alarm occurs at a specified day of the week for
• [
a specified time period. It activates in operated mode when the alarm occurs.
] : Reset all settings.
5. Specify an operation that will perform if an alarm occurs.
• Alarm output : Select whether to set the alarm output if an alarm is incoming, and
specify the alarm output time.
• FTP sending : Specify the use of FTP transfer in the alarm input setup.
• E-mail sending : Specify the use of email transfer in the alarm input setup.
• Record : Specify the use of recording in the alarm input setup.
• Goto Preset : Specify the use of it if the camera moves to a preset position upon
an alarm input
Only if the camera pan/tilt receiver is installed, GoTo Preset is available.
6. When done, click [Apply (
)].
66_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Motion detection
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Motion detection>.
❖ Motion detection
1. Specify the use of motion detection.
2. Select a sensitivity level of the motion
detection.
Higher the sensitivity is, the smaller
motion is detected.
3. Use the drag-and-drop method to
specify the detection area on the video.
4. Specify a detection exception area to
mask.
You can specify up to 4 mask areas.
5. Specify the size of an object that you
want to detect.
6. Select whether to mark the
corresponding region on motion
detection.
- Select <On> to mark a box on the detected moving object on the screen.
7. Specify the activation time and activation condition.
For more information about <Activation time> and <Action>, refer to “Alarm input”. (page 66)
8. When done, click [Apply
(
)
].
If the camera is capturing a short-distant object, the motion detection performance may be
J
degraded.
The motion detection function may not work properly in the following cases:
The object color or brightness is similar to the background.
-
-
-
Multiple movements continue occurring at random due to a scene change or other reasons.
A fixed object continues moving in the same position.
English _67
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
An object hides other objects behind.
-
-
-
Two or more objects overlap or one object divides in multiple portions.
Too fast object (for a proper detection, one object should be found overlapping between
contiguous frames).
Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.
In severe snow, rain, wind or in dawn / dusk.
-
-
-
A moving object comes close to the camera.
Time schedule
You can configure so that an event will occur at a scheduled time regardless of the actual
occurrence of the event.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Time schedule>.
To set the timer event
1. Set <Timer event setup> to <Enable>.
2. Specify the <Activation time>.
• Always : Always activates in operated
mode at the set interval.
• Only scheduled time : Periodically
activates in operated mode at a
specified time and date.
3. Specify the <Transfer interval>.
4. Specify the activation conditions.
• FTP sending : Specify the use of the FTP transfer if an event occurs.
• Record : Specify the use of recording if an event occurs.
5. When done, click [Apply (
)].
68_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Network disconnect
You can perform the saving/relay/preset operation after receiving an event of a physically
disconnected network.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Network disconnect>.
3. Specify the use of “Network
disconnect”.
4. Specify the activation time and
activation condition.
For more information about <Activation
(page 66)
time> and <Action>, refer to “Alarm input”.
5. When done, click [Apply (
)].
Tampering
You can set to trigger an event when a scene is changed on the video screen.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Tampering>.
3. Specify the use of the scene change,
and if you set to use it, select a
sensitivity.
The higher the sensitivity is, the lesser
change can be detected.
4. Specify the activation time and
activation condition.
For more information about <Activation
(page 66)
time> and <Action>, refer to “Alarm input”.
5. When done, click [Apply (
)].
The default change detection function may not work properly in the following cases:
J
A monotonous background or a night/low-contrast scene may deteriorate the detection
-
performance.
A severe shaking of the camera or a drastic change to the illumination can be considered a
scene change by mistake.
-
English _69
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Detection of the scene change may take some time (maximum 3 seconds) right after the
-
-
change was made.
Once a scene change is detected, the network camera will resume a normal operating after a
certain stability time (approx. 3 seconds) during which no detection will be performed.
SYSTEM SETUP
Product information
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Product information>.
3. Check the camera information, or
provide details according to your
network environment.
• Device name : Provide a device
name that will be displayed on the
Live screen.
• Location : Specify the location where the camera is installed.
• Description : Provide detailed information about the camera location.
• Memo : Provide an explanation about the camera for better understanding.
• Language : Select a preferred language for the Web Viewer OSD.
4. When done, click [Apply (
)].
Product related information only allows English for input.
J
Date & Time
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Date & Time>.
3. Specify the time and date that will be
applied to the camera.
• Current system time : Displays the
current time settings of your system.
• Timezone : Specify the local time
zone based on the GMT.
70_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
• Use daylight saving time : If checked, the time will be set one hour before the local
time zone for the specified time period.
This option will be displayed only in areas where DST is applied.
• System time setup : Specify the time and date that will be applied to your system.
- Manual : Specify the time manually.
- Synchronize with NTP server : Sync with the time of the specified server address.
- Synchronize with PC viewer : Synchronize the time with the connected PC.
4. When done, click [Apply (
)].
If the time settings differ between camera and PC, selecting <Synchronize with PC viewer>
may still have a difference. So it is recommended to specify the same time settings for both
camera and PC.
J
User
1. From the Setup menu, select the
<System (
)> tab.
2. Click <User>.
3. Provide the necessary user information.
• Administrator Password Change :
Change the password for the
administrator.
The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
• Guest setup : If <Guest access> is allowed, the user with the guest account who
accesses the web viewer can view only the Live viewer screen.
The ID/password for the guest account is guest/guest, which cannot be changed.
• Current users : You can change the user information and adjust the permission
level for a user who is set to <Enable>.
- Video : You can select a video profile in the Liver viewer screen.
- Audio-In : The audio input option will be activated in the Live Viewer screen.
- Controls : You can control the camera menu buttons.
4. When done, click [Apply (
)].
English _71
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Upgrade / Reboot
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Upgrade / Reboot>.
3. Select a desired item and set it
appropriately.
• Upgrade : Performs upgrading the
system.
• Factory default : Resets the system
to the factory default.
- Except network parameter : Resets all settings except for the Network settings.
- All : Resets all settings including the camera settings. (however, the log
information will not be reset)
The IP addressing system will be defaulted to DHCP if you reset the camera. If no DHCP server is
found, the previous settings will be restored automatically.
• Configuration backup & Restore : Backs up the current system settings before
performing the restoration process. The system is automatically restarts after
backup or restoration.
• Restart : Restarts the system.
To perform the upgrade
1. Click [Upgrade].
2. Click [Browse] and specify a file to
upgrade.
3. Click [Send].
4. The “Upgrade” dialog appears where
the progression will be shown in the
bottom.
If you forcibly terminate the upgrade
M
process, upgrade will not be completed
properly.
72_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
To save the current settings and restore the backup settings
1. Click [Backup].
The Save As dialog should appear.
2. Specify the backup path with a proper
file name, and click [Save].
The backup file will be saved to the
specified path in the format of “.bin”.
3. To restore the backup settings, click
[Restore].
4. Select a backup file and click [Open].
If you perform the backup or restoration,
M
the web browser will be closed and the
camera will reboots.
English _73
Download from Www.Somanuals.com. All Manuals Search And Download.
setup screen
Log
You can check the system log or event log.
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Log>.
3. Select a log type.
• Syslog : You can check the system
logs where any system changes
are recorded including the time
information.
• Evtlog : You can check the event
logs including the time information.
4. From the right log list, select an item to
search for.
• If you select <All> in the top left dropdown list, all logs for the applicable log type
will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to
the previous, next, or the last item.
If you want to view the details of a log, click [Info ( )] in the right column of the log; the log
M
information will be shown in the bottom pane.
Each page displays 15 logs with the latest one displayed at the top.
The event/system log list can contain up to 1000 logs; after that, the existing logs will be deleted
from the oldest one each time a new log is created.
74_ setup screen
Download from Www.Somanuals.com. All Manuals Search And Download.
appendix
SPECIFICATION
Items
Description
Imaging Device
Total Pixels
1/3” Super-HAD PS CCD
NTSC : 811(H) x 508(V),
PAL : 795(H) x 596(V)
NTSC : 768(H) x 494(V),
PAL : 752(H) x 582(V)
Progressive (If WDR on, Interlaced Scan)
Effective Pixels
Scanning System
Frequency
Video
Lens
NTSC : H : 15.734KHz / V : 59.94Hz,
PAL : H : 15.625KHz / V : 50Hz
Horizontal Resolution
Min. Illumination
S / N Ratio
Color : 600 TV lines
0.00008 Lux (Sens up 512X)
52dB
CVBS : 1.0 Vp-p / 75Ω composite
-
-
-
Video Out
Focal Length (Zoom Ratio)
Max. Aperture Ratio
Angular Field of View
Min. Object Distance
Focus Cotrol
-
-
Lens Type
Manual / DC auto Iris
C/CS
Mount Type
English _75
Download from Www.Somanuals.com. All Manuals Search And Download.
appendix
Items
Description
Off / On (Displayed up to 15 characters)
Color / B/W / Auto (IR Cut Filter) / External
Off / BLC / WDR
NTSC : 128X, PAL : 160X
SSDR (Samsung Super Dynamic Range) (Off / On)
Camera Title
Day & Night
Backlight Compensation
Wide Dynamic Range
Contrast Enhancement
Motion Adaptive 2D+3D Noise Filter (Off/Low/Middle/High/
Digital Noise Reduction
User)
Digital Image Stabilization
Off / On
Motion Detection
Off / On (4 programmable mask zones)
Off / On (12 Polygonal programmable zones, 4 points
Privacy Masking
polygonal Method)
Operational
Sens-up
Off / Auto (2X ~ 512X)
(Frame Integration)
Gain Control
AGC (Low / Middle / High)
ATW1 / ATW2 / AWC / 3200K / 5600K
White Balance
NTSC : 1/60 ~ 1/10Ksec,
Electronic Shutter Speed
PAL : 1/50 ~ 1/10Ksec
Flip / Mirror
Off / On
Tampering
Input 1ea / Output 1ea (Relay)
RS-485
SAMSUNG T/E, PELCO-P/D, SUNGJIN
Intelligent Video Analytics
Alarm I/O
Remote Control Interface
RS-485 Protocol
76_ appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Items
Description
Ethernet
RJ-45 (10/100BASE-T)
Video Compression Format
Resolution
H.264, MPEG-4, MJPEG
NTSC : 704x480, 640x480, 352x240, 320x240
PAL : 704x576, 640x480, 352x288, 320x240
Max. Framerate
NTSC : 30fps, PAL : 25fps
H.264/MPEG-4 : Compression Level, Target Bitrate Level
Control
Video Quality Adjustment
MJPEG : Quality Level Control
H.264/MPEG-4 : CBR or VBR
Bitrate Control Method
MJPEG : VBR
Streaming Capability
Audio I/O
Multiple Streaming (Up to 10 Profiles)
Mic / Line in, Line out
G.711 μ-law
Bi-directonal audio
IPv4, IPv6
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP,
HTTPS, SSL, DHCP, PPPoE, FTP, SMTP, ICMP, IGMP,
SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS
Network
Audio Compression Format
Audio Communication
IP
Protocol
HTTPS(SSL) Login Authentication
Digest Login Authentication
IP Address Filtering
Security
User access Log
802.1x Authentication
Streaming Method
Max. User Access
Unicast / Multicast
10 users at Unicast Mode
English _77
Download from Www.Somanuals.com. All Manuals Search And Download.
appendix
Items
Description
Memory Slot
SD/SDHC Memory Slot
Yes
ONVIF Conformance
English, French, German, Spanish, Italian, Chinese, Korean,
Russian, Japanese, Swedish, Denish, Portuguese, Czech,
Polish, Turkish, Rumanian, Serbian, Dutch, Croatian,
Hungarian, Greek
Language
Network
Supported OS : Windows XP / VISTA / 7, MAC OS
Supported Browser : Internet Explorer 7.0 or Higher,
Firefox 3.0 or Higher, Chrome 8.0 or
Higher, Safari 4.0 or Higher
Web Viewer
Central Management Software NET-i viewer
Operating Temperature /
-10°C ~ +50°C (+14°F ~ +122°F) / 20% ~ 80% RH
Humidity
Environmental
Storage Temperature / Humidity -30°C ~ +60°C (-22°F ~ +140°F) / ~ 90% RH
Ingress Protection
Input Voltage / Current
Power Consumption
Color / Material
-
12V DC, 24V AC, PoE(IEEE802.3af)
Max. 6W
Body : Silver / Metal
W72.0 x H60.0 x D136.8 mm
420g
Electrical
Mechanical
Dimension (W x H x D)
Weight
78_ appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT OVERVIEW
Unit : mm (inch)
XZ_U]O\U[\IP
XZ]U_O\UZ_IP
^Y OYU_ZIP
English _79
Download from Www.Somanuals.com. All Manuals Search And Download.
appendix
TROUBLESHOOTING
PROBLEM
SOLUTION
y Check to make sure that the camera’s Network settings are appropriate.
y Check to make sure that all network cables have been connected
properly.
I can’t access the camera from a
web browser.
y If connected using DHCP, verify that the camera is able to acquire
dynamic IP addresses without any problem.
y If the camera is connected to a Broadband Router, verify that port
forwarding is properly configured.
y Connected Viewers become disconnected upon any change to camera
or network configurations.
Viewer got disconnected during
monitoring.
y Check all network connections.
y If the camera is connected over an PPPoE network, it’ s possible for
Viewer to disconnect under poor network conditions.
y When you try to connect to the system using a tab browser, the same
cookie information is shared, resulting in errors when connected.
Therefore, instead of using a tab browser, open a new browser window
to connect to the system.
I cannot connect to the system
using a tab browser of Internet
Explorer 7.0.
The camera connected to the
network is not detected in the IP
installer program.
y Turn off the firewall settings on your PC and then search the camera
again.
y Check whether two or more cameras are set to a single multicast
address instead of different addresses. If a single address is used for
multiple cameras, the images may overlap.
Images overlap.
y If the transmission method is set to multicast, check whether there is a
No image appears.
router that supports multicast in the LAN the camera is connected to.
80_ appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
SOLUTION
Cannot record into the SD memory
y Check if the memory card is defective.
card.
y Check if the memory card is inserted in the proper direction. Operation
of memory card that is formatted by other devices is not guaranteed with
this camera unit
A SD memory card is inserted but
the product does not recognize it.
y Format the memory card again in <Setup> <Event>
<SD Record> menu.
Cannot format the SD memory
card.
y Check if the memory card is defective.
English _81
Download from Www.Somanuals.com. All Manuals Search And Download.
OPEN SOURCE ANNOUNCEMENT
Some software components of this product incorporate source code covered under the BSD license as follows.
Component Name
License
License URL
lighttpd 1.4.25
librtp 1.20
BSD 2.0
BSD 1.0
BSD
net-snmp-5.4
lighttpd is a secure, fast, compliant, and very flexible web-
server that has been optimized for high-performance
environments. It has a very low memory footprint
compared to other webservers and takes care of cpu-
Copyright (c) 1998-2001 University College
London
All rights reserved.
load. Its advanced feature-set (FastCGI, CGI, Auth, Output-
Compression, URL-Rewriting and many more) make lighttpd
the perfect webserver-software for every server that suffers
load problems.
Redistribution and use in source and binary forms, with or
without modification, is permitted provided that the following
conditions are met :
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
This product includes software developed by the Computer
Science Department at University College London.
4. Neither the name of the University nor of the Department
may be used to endorse or promote products derived from
this software without specific prior written permission.
Simple Network Management Protocol (SNMP) is an Internet-
standard protocol for managing devices on IP networks. It
is used mostly in network management systems to monitor
the devices attached to the network for conditions that need
administrative attention. Net-SNMP is a suite of applications
used to implement SNMP v1, SNMP v2c and SNMP v3
using both IPv4 and IPv6.
For more additional information, send email to help.cctv@
samsung.com.
Copyright (C) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met :
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND
CONTRIBUTORS ``AS IS’’ AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSEARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
- Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
- Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of the ‘incremental’ nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Download from Www.Somanuals.com. All Manuals Search And Download.
LICENSE
Various copyrights apply to this package, listed in various
separate parts below. Please make sure that you read all the
parts.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 1: CMU/UCD copyright notice: (BSD like)
Part 3: Cambridge Broadband Ltd. copyright
notice (BSD)
Copyright 1989, 1991, 1992 by Carnegie Mellon University
Derivative Work - 1996, 1998-2000
Portions of this code are copyright (c) 2001-2003, Cambridge
Broadband Ltd.
Copyright 1996, 1998-2000 The Regents of the University of
California
All Rights Reserved
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
Permission to use, copy, modify and distribute this software
and its documentation for any purpose and without fee is
hereby granted, provided that the above copyright notice
appears in all copies and that both that copyright notice and
this permission notice appear in supporting documentation,
and that the name of CMU and The Regents of the University
of California not be used in advertising or publicity pertaining
to distribution of the software without specific written
permission.
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
CMU AND THE REGENTS OF THE UNIVERSITY OF
The name of Cambridge Broadband Ltd. may not be used
CALIFORNIA DISCLAIM ALL WARRANTIES WITH
to endorse or promote products derived from this software
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS.
IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
OR ANY DAMAGES WHATSOEVER RESULTING FROM
THE LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION
WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 2: Networks Associates Technology, Inc
copyright notice (BSD)
Copyright (c) 2001-2003, Networks Associates Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
Part 4: Sun Microsystems, Inc. copyright notice
Redistributions of source code must retain the above
(BSD)
copyright notice, this list of conditions and the following
disclaimer.
Copyright © 2003 Sun Microsystems, Inc., 4150 Network
Circle, Santa Clara,
Redistributions in binary form must reproduce the above
California 95054, U.S.A.
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
All rights reserved.
Use is subject to license terms below. This distribution
may include materials developed by third parties. Sun, Sun
Microsystems, the Sun logo and Solaris are trademarks or
registered trademarks of Sun Microsystems, Inc. in the U.S.
and other countries. Redistribution and use in source and
binary forms, with or without modification, are permitted
provided that the following conditions are met:
Neither the name of the Networks Associates Technology,
Inc nor the names of its contributors may be used to
endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
Neither the name of the Sun Microsystems, Inc. nor the
names of its contributors may be used to endorse or
promote products derived from this software without
specific prior written permission.
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Neither the name of Cisco, Inc, Beijing University of
Posts and Telecommunications, nor the names of their
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 5: Sparta, Inc copyright notice (BSD)
Copyright (c) 2003-2009, Sparta, Inc
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
Part 7: Fabasoft R&D Software GmbH & Co KG
copyright notice (BSD)
Redistributions of source code must retain the above
Copyright (c) Fabasoft R&D Software GmbH & Co KG, 2003
copyright notice, this list of conditions and the following
disclaimer.
Author: Bernhard Penz
Redistributions in binary form must reproduce the above
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
Redistributions of source code must retain the above
Neither the name of Sparta, Inc nor the names of its
copyright notice, this list of conditions and the following
disclaimer.
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
The name of Fabasoft R&D Software GmbH & Co KG or
any of its subsidiaries, brand or product names may not
be used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDER BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD)
Copyright (c) 2004, Cisco, Inc and Information Network
Center of Beijing University of Posts and Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
Part 8: Apple Inc. copyright notice (BSD)
Copyright (c) 2007 Apple Inc.
All rights reserved.
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. Neither the name of Apple Inc. (“Apple”) nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL APPLE OR ITSCONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Part 9: ScienceLogic, LLC copyright notice
(BSD)
Copyright (c) 2009, ScienceLogic, LLC
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions aremet:
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
Neither the name of ScienceLogic, LLC nor the names
of its contributors may be used to endorse or promote
products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Download from Www.Somanuals.com. All Manuals Search And Download.
GPL/LGPL SOFTWARE LICENSE
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain
the complete Corresponding Source code from us for a period of three years after our last shipment of this product by
sending email to [email protected]
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of
physically performing source distribution might be charged.
•
•
GPL S/W
-
Base Kernel, Busybox, Sysvinit, dosfstools
LGPL S/W
gLibc, Inetutils
-
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a
free program will individually obtain patent licenses, in effect
making the program proprietary. To prevent this, we have
made it clear that any patent must be licensed for everyone’s
free use or not licensed at all.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C)1989, 1991 Free Software Foundation, Inc.
51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
The precise terms and conditions for copying, distribution
and modification follow.
Preamble
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your
freedom to share and change free software-- to make sure
the software is free for all its users.
Version 2, June 1991 Copyright (C) 1989, 1991 Free
Software Foundation, Inc. 51 Franklin S
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying
it may be distributed under the terms of this General
Public License.
This General Public License applies to most of the Free
Software Foundation’s software and to any other program
whose authors commit to using it. (Some other Free Software
Foundation software is covered by the GNU Lesser General
Public License instead.) You can apply it to your programs, too.
The “Program”, below, refers to any such program or
work, and a “work based on the Program” means either
the Program or any derivative work under copyright
law : that is to say, a work containing the Program or a
portion of it, either verbatim or with modifications and/or
translated into another language. (Hereinafter, translation
is included without limitation in the term “modification”.)
Each licensee is addressed as “you”.
When we speak of free software, we are referring to freedom,
not price.
Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source
code or can get it if you want it, that you can change the
software or use pieces of it in new free programs ; and that
you know you can do these things.
Activities other than copying, distribution and modification
are not covered by this License ; they are outside its scope.
The act of running the Program is not restricted, and the
output from the Program is covered only if its contents
constitute a work based on the Program (independent of
having been made by running the Program). Whether that is
true depends on what the Program does.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the software,
or if you modify it.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer
to this License and to the absence of any warranty ; and
give any other recipients of the Program a copy of this
License along with the Program.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have.
You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they
know their rights.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection
in exchange for a fee.
We protect your rights with two steps :
(1)copyright the software, and (2)offer you this license which
gives you legal permission to copy, distribute and/or modify
the software.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions :
Also, for each author’s protection and ours, we want to make
certain that everyone understands that there is no warranty
for this free software. If the software is modified by someone
else and passed on, we want its recipients to know that what
they have is not the original, so that any problems introduced
by others will not reflect on the original authors’ reputations.
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date
of any change.
Download from Www.Somanuals.com. All Manuals Search And Download.
b) You must cause any work that you distribute or publish,
that in whole or in part contains or is derived from
the Program or any part thereof, to be licensed as a
whole at no charge to all third parties under the terms
of this License.
c) If the modified program normally reads commands
interactively when run,you must cause it, when started
running for such interactive use in the most ordinary
way, to print or display an announcement including
an appropriate copyright notice and a notice that
there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program
under these conditions, and telling the user how to
view a copy of this License. (Exception:if the Program
itself is interactive but does not normally print such an
announcement, your work based on the Program is not
required to print an announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent
and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms
of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part
regardless of who wrote it.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from the
same place counts as distribution of the source code, even
though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or
distribute the Program is void, and will automatically
terminate your rights under this License.
However, parties who have received copies, or rights, from
you under this License will not have their licenses terminated
so long as such parties remain in full compliance.
5. You are not required to accept this License, since you
have not signed it.
However, nothing else grants you permission to modify or
distribute the Program or its derivative works.
These actions are prohibited by law if you do not accept
this License.Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate
your acceptance of this License to do so, and all its terms
and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based
on the Program), the recipient automatically receives a
license from the original licensor to copy, distribute or
modify the Program subject to these terms and conditions.
You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein.
You are not responsible for enforcing compliance by third
parties to this License.
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether
by court order, agreement or otherwise)that contradict the
conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so
as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a
consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-
free redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended
to apply in other circumstances. It is not the purpose of
this section to induce you to infringe any patents or other
property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the
integrity of the free software distribution system, which is
implemented by public license practices. Many people have
made generous contributions to the wide range of software
distributed through that system in reliance on consistent
application of that system ; it is up to the author/donor to
decide if he or she is willing to distribute software through
any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you ; rather,
the intent is to exercise the right to control the distribution
of derivative or collective works based on the Program. In
addition, mere aggregation of another work not based on
the Program with the Program (or with a work based on the
Program)on a volume of a storage or distribution medium does
not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work
based on it, under Section 2)in object code or executable
form under the terms of Sections 1 and 2 above provided
that you also do one of the following :
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange ; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machinereadable copy of the corresponding
source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange ; or,
c) Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of
the work for making modifications to it. For an executable
work, complete source code means all the source code
for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation
and installation of the executable. However, as a special
exception, the source code distributed need not include
anything that is normally distributed (in either source or binary
form)with the major components (compiler, kernel, and so on)
of the operating system on which the executable runs, unless
that component itself accompanies the executable.
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the
Program under this License may add an explicit geographical
distribution limitation excluding those countries,so that
distribution is permitted only in or among countries not
thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
Download from Www.Somanuals.com. All Manuals Search And Download.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to the
present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If the
Program specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Program does not specify a version number of this
License, you may choose any version ever published by the
Free Software Foundation.
one line to give the program’s name and an idea of what it
does.
Copyright (C)yyyy name of author
This program is free software ; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation ; either version
2 of the License, or (at your option)any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY ; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation,write to the Free Software Foundation ; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the
sharing and reuse of software generally.
You should have received a copy of the GNU General Public
License along with this program ; if not, write to the Free
Software Foundation, Inc.,51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic
and paper mail. If the program is interactive, make it output a
short notice like this when it starts in an interactive mode :
Gnomovision version 69,
Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO
WARRANTY ; for details type ‘show w’. This is free software,
and you are welcome to redistribute it under certain
conditions ; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called something
other than ‘show w’ and ‘show c’ ; they could even be
mouse-clicks or menu items-- whatever suits your program.
You should also get your employer (if you work as a
programmer)or your school, if any, to sign a “copyright
disclaimer” for the program,if necessary. Here is a sample ;
alter the names:
Yoyodyne, Inc.,hereby disclaims all copyright interest in the
program ‘Gnomovision’ (which makes passes at compilers)
written by James Hacker.
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program
is a subroutine library, you may consider it more useful to
permit linking proprietary applications with the library. If this is
what you want to do, use the GNU Lesser General Public
License instead of this License.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“ASIS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH
YOU. SHOULD THE PROGRAMPROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
org/>
END OF TERMS AND CONDITIONS
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
How to Apply These Terms to Your New
Programs
Preamble
If you develop a new program, and you want it to be of
the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone can
redistribute and change under these terms.
The GNU General Public License is a free, copyleft
license for software and other kinds of works. The licenses
for most software and other practical works are designed
to take away your freedom to share and change the works.
By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change all versions of
a program--to make sure it remains free software for all its
users.
To do so, attach the following notices to the program. It is
safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty ; and each file
should have at least the “copyright” line and a pointer to
where the full notice is found.
Download from Www.Somanuals.com. All Manuals Search And Download.
We, the Free Software Foundation, use the GNU General
Public License for most of our software; it applies also to any
other work released this way by its authors.
called a “modified version” of the earlier work or a work “based
on” the earlier work.
A “covered work” means either the unmodified Program or a
You can apply it to your programs, too.
work based on the Program.
When we speak of free software, we are referring to freedom,
not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free
software (and charge for them if you wish), that you receive
source code or can get it if you want it, that you can change
the software or use pieces of it in new free programs, and
that you know you can do these things.
To protect your rights, we need to prevent others from
denying you these rights or asking you to surrender
the rights. Therefore, you have certain responsibilities if
you distribute copies of the software, or if you modify it:
responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must pass on to the recipients
the same freedoms that you received. You must make sure
that they, too, receive or can get the source code. And you
must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with
two steps: (1) assert copyright on the software, and (2)
offer you this License giving you legal permission to copy,
distribute and/or modify it.
To “propagate” a work means to do anything with it that,
without permission, would make you directly or secondarily
liable for infringement under applicable copyright law, except
executing it on a computer or modifying a private copy.
Propagation includes copying, distribution (with or without
modification), making available to the public, and in some
countries other activities as well.
To “convey” a work means any kind of propagation that
enables other parties to make or receive copies. Mere
interaction with a user through a computer network, with no
transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal
Notices” to the extent that it includes a convenient and
prominently visible feature that (1) displays an appropriate
copyright notice, and (2) tells the user that there is no
warranty for the work (except to the extent that warranties
are provided), that licensees may convey the work under
this License, and how to view a copy of this License. If the
interface presents a list of user commands or options, such
as a menu, a prominent item in the list meets this criterion.
1. Source Code.
For the developers’ and authors’ protection, the GPL clearly
explains that there is no warranty for this free software.
For both users’ and authors’ sake, the GPL requires that
modified versions be marked as changed, so that their
problems will not be attributed erroneously to authors of
previous versions.
The “source code” for a work means the preferred form of
the work for making modifications to it. “Object code” means
any non-source form of a work.
A “Standard Interface” means an interface that either is
an official standard defined by a recognized standards
body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among
developers working in that language.
Some devices are designed to deny users access to install
or run modified versions of the software inside them,
although the manufacturer can do so. This is fundamentally
incompatible with the aim of protecting users’ freedom to
change the software. The systematic pattern of such abuse
occurs in the area of products for individuals to use, which is
precisely where it is most unacceptable. Therefore, we have
designed this version of the GPL to prohibit the practice for
those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those
domains in future versions of the GPL, as needed to protect
the freedom of users.
The “System Libraries” of an executable work include
anything, other than the work as a whole, that (a) is included
in the normal form of packaging a Major Component,
but which is not part of that Major Component, and (b)
serves only to enable use of the work with that Major
Component, or to implement a Standard Interface for which
an implementation is available to the public in source code
form. A “Major Component”, in this context, means a major
essential component (kernel, window system, and so on) of
the specific operating system (if any) on which the executable
work runs, or a compiler used to produce the work, or an
object code interpreter used to run it.
Finally, every program is threatened constantly by software
patents. States should not allow patents to restrict
development and use of software on general-purpose
computers, but in those that do, we wish to avoid the special
danger that patents applied to a free program could make it
effectively proprietary. To prevent this, the GPL assures that
patents cannot be used to render the program non-free.
The “Corresponding Source” for a work in object code form
means all the source code needed to generate, install, and (for
an executable work) run the object code and to modify the
work, including scripts to control those activities. However,
it does not include the work’s System Libraries, or general-
purpose tools or generally available free programs which are
used unmodified in performing those activities but which are
not part of the work. For example, Corresponding Source
includes interface definition files associated with source files
for the work, and the source code for shared libraries and
dynamically linked subprograms that the work is specifically
designed to require, such as by intimate data communication
or control flow between those subprograms and other parts
of the work.
The precise terms and conditions for copying, distribution
and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public
License.
“Copyright” also means copyright-like laws that apply to
other kinds of works, such as semiconductor masks.
The Corresponding Source need not include anything that
users can regenerate automatically from other parts of the
Corresponding Source.
“The Program” refers to any copyrightable work licensed
under this License. Each licensee is addressed as “you”.
“Licensees” and “recipients” may be individuals or
organizations.
The Corresponding Source for a work in source code form is
that same work.
To “modify” a work means to copy from or adapt all or part
of the work in a fashion requiring copyright permission, other
than the making of an exact copy. The resulting work is
2. Basic Permissions.
All rights granted under this License are granted for the term
of copyright on the Program, and are irrevocable provided
Download from Www.Somanuals.com. All Manuals Search And Download.
the stated conditions are met. This License explicitly affirms
your unlimited permission to run the unmodified Program.
The output from running a covered work is covered by this
License only if the output, given its content, constitutes a
covered work. This License acknowledges your rights of fair
use or other equivalent, as provided by copyright law.
d) If the work has interactive user interfaces, each must
display Appropriate Legal Notices; however, if the Program
has interactive interfaces that do not display Appropriate
Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and
independent works, which are not by their nature extensions
of the covered work, and which are not combined with it
such as to form a larger program, in or on a volume of a
storage or distribution medium, is called an “aggregate” if the
compilation and its resulting copyright are not used to limit
the access or legal rights of the compilation’s users beyond
what the individual works permit. Inclusion of a covered work
in an aggregate does not cause this License to apply to the
other parts of the aggregate.
You may make, run and propagate covered works that you
do not convey, without conditions so long as your license
otherwise remains in force. You may convey covered
works to others for the sole purpose of having them make
modifications exclusively for you, or provide you with facilities
for running those works, provided that you comply with the
terms of this License in conveying all material for which you
do not control copyright. Those thus making or running the
covered works for you must do so exclusively on your behalf,
under your direction and control, on terms that prohibit them
from making any copies of your copyrighted material outside
their relationship with you.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under
the terms of sections 4 and 5, provided that you also convey
the machine-readable Corresponding Source under the
terms of this License, in one of these ways:
Conveying under any other circumstances is permitted
solely under the conditions stated below. Sublicensing is not
allowed; section 10 makes it unnecessary.
a) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by the Corresponding Source fixed on a
durable physical medium customarily used for software
interchange.
3. Protecting Users’ Legal Rights From Anti-
Circumvention Law.
No covered work shall be deemed part of an effective
technological measure under any applicable law fulfilling
obligations under article 11 of the WIPO copyright treaty
adopted on 20 December 1996, or similar laws prohibiting or
restricting circumvention of such measures.
b) Convey the object code in, or embodied in, a physical
product (including a physical distribution medium),
accompanied by a written offer, valid for at least three
years and valid for as long as you offer spare parts or
customer support for that product model, to give anyone
who possesses the object code either (1) a copy of the
Corresponding Source for all the software in the product
that is covered by this License, on a durable physical
medium customarily used for software interchange, for
a price no more than your reasonable cost of physically
performing this conveying of source, or (2) access to
copy the Corresponding Source from a network server
at no charge.
c) Convey individual copies of the object code with a
copy of the written offer to provide the corresponding
Source. This alternative is allowed only occasionally and
noncommercially, and only if you received the object code
with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a
designated place (gratis or for a charge), and offer
equivalent access to the Corresponding Source in the
same way through the same place at no further charge.
You need not require recipients to copy the Corresponding
Source along with the object code. If the place to copy
the object code is a network server, the Corresponding
Source may be on a different server (operated by you or
a third party) that supports equivalent copying facilities,
provided you maintain clear directions next to the object
code saying where to find the Corresponding Source.
Regardless of what server hosts the Corresponding
Source, you remain obligated to ensure that it is available
for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission,
provided you inform other peers where the object code
and Corresponding Source of the work are being offered
to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is
excluded from the Corresponding Source as a System Library,
need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which
means any tangible personal property which is normally
used for personal, family, or household purposes, or (2)
anything designed or sold for incorporation into a dwelling.
In determining whether a product is a consumer product,
When you convey a covered work, you waive any legal
power to forbid circumvention of technological measures to
the extent such circumvention is effected by exercising rights
under this License with respect to the covered work, and
you disclaim any intention to limit operation or modification of
the work as a means of enforcing, against the work’s users,
your or third parties’ legal rights to forbid circumvention of
technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source
code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an
appropriate copyright notice; keep intact all notices stating
that this License and any non-permissive terms added in
accord with section 7 apply to the code; keep intact all
notices of the absence of any warranty; and give all recipients
a copy of this License along with the Program.
You may charge any price or no price for each copy that you
convey, and you may offer support or warranty protection for a
fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the
modifications to produce it from the Program, in the form of
source code under the terms of section 4, provided that you
also meet all of these conditions:
a) The work must carry prominent notices stating that you
modified it, and giving a relevant date.
b) The work must carry prominent notices stating that
it is released under this License and any conditions
added under section 7. This requirement modifies the
requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this
License to anyone who comes into possession of a copy.
This License will therefore apply, along with any applicable
section 7 additional terms, to the whole of the work, and
all its parts, regardless of how they are packaged. This
License gives no permission to license the work in any
other way, but it does not invalidate such permission if you
have separately received it.
Download from Www.Somanuals.com. All Manuals Search And Download.
doubtful cases shall be resolved in favor of coverage. For
a particular product received by a particular user, “normally
used” refers to a typical or common use of that class of
product, regardless of the status of the particular user or of
the way in which the particular user actually uses, or expects
or is expected to use, the product. A product is a consumer
product regardless of whether the product has substantial
commercial, industrial or non-consumer uses, unless such
uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means
any methods, procedures, authorization keys, or other
information required to install and execute modified versions
of a covered work in that User Product from a modified
version of its Corresponding Source. The information must
suffice to ensure that the continued functioning of the
modified object code is in no case prevented or interfered
with solely because modification has been made.
If you convey an object code work under this section in,
or with, or specifically for use in, a User Product, and the
conveying occurs as part of a transaction in which the right of
possession and use of the User Product is transferred to the
recipient in perpetuity or for a fixed term (regardless of how
the transaction is characterized), the Corresponding Source
conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply
if neither you nor any third party retains the ability to install
modified object code on the User Product (for example, the
work has been installed in ROM).
The requirement to provide Installation Information does not
include a requirement to continue to provide support service,
warranty, or updates for a work that has been modified or
installed by the recipient, or for the User Product in which it
has been modified or installed. Access to a network may be
denied when the modification itself materially and adversely
affects the operation of the network or violates the rules and
protocols for communication across the network.
c) Prohibiting misrepresentation of the origin of that material,
or requiring that modified versions of such material be
marked in reasonable ways as different from the original
version; or
d) Limiting the use for publicity purposes of names of
licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of
some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that
material by anyone who conveys the material (or modified
versions of it) with contractual assumptions of liability
to the recipient, for any liability that these contractual
assumptions directly impose on those licensors and
authors.
All other non-permissive additional terms are considered
“further restrictions” within the meaning of section 10. If
the Program as you received it, or any part of it, contains a
notice stating that it is governed by this License along with a
term that is a further restriction, you may remove that term. If
a license document contains a further restriction but permits
relicensing or conveying under this License, you may add
to a covered work material governed by the terms of that
license document, provided that the further restriction does
not survive such relicensing or conveying.
If you add terms to a covered work in accord with this
section, you must place, in the relevant source files, a
statement of the additional terms that apply to those files, or
a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be
stated in the form of a separately written license, or stated as
exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as
expressly provided under this License. Any attempt otherwise
to propagate or modify it is void, and will automatically
terminate your rights under this License (including any patent
licenses granted under the third paragraph of section 11).
Corresponding Source conveyed, and Installation Information
provided, in accord with this section must be in a format that
is publicly documented (and with an implementation available
to the public in source code form), and must require no
special password or key for unpacking, reading or copying.
However, if you cease all violation of this License, then your
license from a particular copyright holder is reinstated (a)
provisionally, unless and until the copyright holder explicitly
and finally terminates your license, and (b) permanently, if the
copyright holder fails to notify you of the violation by some
reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is
reinstated permanently if the copyright holder notifies you of
the violation by some reasonable means, this is the first time
you have received notice of violation of this License (for any
work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice.
7. Additional Terms.
“Additional permissions” are terms that supplement the
terms of this License by making exceptions from one or more
of its conditions. Additional permissions that are applicable
to the entire Program shall be treated as though they were
included in this License, to the extent that they are valid
under applicable law. If additional permissions apply only to
part of the Program, that part may be used separately under
those permissions, but the entire Program remains governed
by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your
option remove any additional permissions from that copy, or
from any part of it. (Additional permissions may be written to
require their own removal in certain cases when you modify
the work.) You may place additional permissions on material,
added by you to a covered work, for which you have or can
give appropriate copyright permission.
Termination of your rights under this section does not
terminate the licenses of parties who have received copies
or rights from you under this License. If your rights have
been terminated and not permanently reinstated, you do not
qualify to receive new licenses for the same material under
section 10.
9. Acceptance Not Required for Having Copies.
Notwithstanding any other provision of this License, for
material you add to a covered work, you may (if authorized
by the copyright holders of that material) supplement the
terms of this License with terms:
You are not required to accept this License in order to receive
or run a copy of the Program. Ancillary propagation of a
covered work occurring solely as a consequence of using
peer-to-peer transmission to receive a copy likewise does
not require acceptance. However, nothing other than this
License grants you permission to propagate or modify any
covered work. These actions infringe copyright if you do not
accept this License. Therefore, by modifying or propagating
a covered work, you indicate your acceptance of this License
to do so.
a) Disclaiming warranty or limiting liability differently from the
terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices
or author attributions in that material or in the Appropriate
Legal Notices displayed by works containing it; or
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Automatic Licensing of Downstream Recipients.
If, pursuant to or in connection with a single transaction
or arrangement, you convey, or propagate by procuring
conveyance of, a covered work, and grant a patent license
to some of the parties receiving the covered work authorizing
them to use, propagate, modify or convey a specific copy
of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work
and works based on it.
Each time you convey a covered work, the recipient
automatically receives a license from the original licensors, to
run, modify and propagate that work, subject to this License.
You are not responsible for enforcing compliance by third
parties with this License.
An “entity transaction” is a transaction transferring control
of an organization, or substantially all assets of one, or
subdividing an organization, or merging organizations.
If propagation of a covered work results from an entity
transaction, each party to that transaction who receives a
copy of the work also receives whatever licenses to the work
the party’s predecessor in interest had or could give under
the previous paragraph, plus a right to possession of the
Corresponding Source of the work from the predecessor in
interest, if the predecessor has it or can get it with reasonable
efforts.
A patent license is “discriminatory” if it does not include
within the scope of its coverage, prohibits the exercise of,
or is conditioned on the non-exercise of one or more of
the rights that are specifically granted under this License.
You may not convey a covered work if you are a party to
an arrangement with a third party that is in the business of
distributing software, under which you make payment to the
third party based on the extent of your activity of conveying
the work, and under which the third party grants, to any of
the parties who would receive the covered work from you, a
discriminatory patent license
You may not impose any further restrictions on the exercise
of the rights granted or affirmed under this License. For
example, you may not impose a license fee, royalty, or other
charge for exercise of rights granted under this License,
and you may not initiate litigation (including a cross-claim
or counterclaim in a lawsuit) alleging that any patent claim
is infringed by making, using, selling, offering for sale, or
importing the Program or any portion of it.
(a) in connection with copies of the covered work conveyed
by you (or copies made from those copies), or
(b) primarily for and in connection with specific products or
compilations that contain the covered work, unless you
entered into that arrangement, or that patent license was
granted, prior to 28 March 2007.
11. Patents.
Nothing in this License shall be construed as excluding or
limiting any implied license or other defenses to infringement
that may otherwise be available to you under applicable
patent law.
A “contributor” is a copyright holder who authorizes use
under this License of the Program or a work on which the
Program is based. The work thus licensed is called the
contributor’s “contributor version”.
12. No Surrender of Others’ Freedom.
A contributor’s “essential patent claims” are all patent claims
owned or controlled by the contributor, whether already
acquired or hereafter acquired, that would be infringed by
some manner, permitted by this License, of making, using,
or selling its contributor version, but do not include claims
that would be infringed only as a consequence of further
modification of the contributor version. For purposes of
this definition, “control” includes the right to grant patent
sublicenses in a manner consistent with the requirements of
this License.
Each contributor grants you a non-exclusive, worldwide,
royalty-free patent license under the contributor’s essential
patent claims, to make, use, sell, offer for sale, import and
otherwise run, modify and propagate the contents of its
contributor version.
In the following three paragraphs, a “patent license” is any
express agreement or commitment, however denominated,
not to enforce a patent (such as an express permission
to practice a patent or covenant not to sue for patent
infringement). To “grant” such a patent license to a party
means to make such an agreement or commitment not to
enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent
license, and the Corresponding Source of the work is not
available for anyone to copy, free of charge and under the
terms of this License, through a publicly available network
server or other readily accessible means, then you must
either (1) cause the Corresponding Source to be so available,
or (2) arrange to deprive yourself of the benefit of the patent
license for this particular work, or (3) arrange, in a manner
consistent with the requirements of this License, to extend
the patent license to downstream recipients. “Knowingly
relying” means you have actual knowledge that, but for the
patent license, your conveying the covered work in a country,
or your recipient’s use of the covered work in a country,
would infringe one or more identifiable patents in that country
that you have reason to believe are valid.
If conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this
License. If you cannot convey a covered work so as to satisfy
simultaneously your obligations under this License and any
other pertinent obligations, then as a consequence you may
not convey it at all. For example, if you agree to terms that
obligate you to collect a royalty for further conveying from
those to whom you convey the Program, the only way you
could satisfy both those terms and this License would be to
refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you
have permission to link or combine any covered work with
a work licensed under version 3 of the GNU Affero General
Public License into a single combined work, and to convey
the resulting work. The terms of this License will continue to
apply to the part which is the covered work, but the special
requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will
apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/ or
new versions of the GNU General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
Program specifies that a certain numbered version of the
GNU General Public License “or any later version” applies to
it, you have the option of following the terms and conditions
either of that numbered version or of any later version
published by the Free Software Foundation. If the Program
does not specify a version number of the GNU General
Public License, you may choose any version ever published
by the Free Software Foundation.
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Program specifies that a proxy can decide which future
versions of the GNU General Public License can be used,
that proxy’s public statement of acceptance of a version
permanently authorizes you to choose that version for the
Program.
Later license versions may give you additional or different
permissions. However, no additional obligations are imposed
on any author or copyright holder as a result of your choosing
to follow a later version.
15. Disclaimer of Warranty.
This license, the Lesser General Public License, applies
to some specially designated software packages-typically
libraries-of the Free Software Foundation and other authors
who decide to use it. You can use it too, but we suggest you
first think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any
particular case, based on the explanations below.
When we speak of free software, we are referring to freedom
of use, not price. Our General Public Licenses are designed
to make sure that you have the freedom to distribute copies
of free software (and charge for this service if you wish); that
you receive source code or can get it if you want it; that you
can change the software and use pieces of it in new free
programs; and that you are informed that you can do these
things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library or
if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the rights
that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object files to the
recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you
must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify
the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the library
is modified by someone else and passed on, the recipients
should know that what they have is not the original version,
so that the original author’s reputation will not be affected by
problems that might be introduced by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained
for a version of the library must be consistent with the full
freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain
libraries in order to permit linking those libraries into non-free
programs.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO
YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided
above cannot be given local legal effect according to their
terms, reviewing courts shall apply local law that most
closely approximates an absolute waiver of all civil liability
in connection with the Program, unless a warranty or
assumption of liability accompanies a copy of the Program in
return for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library.
The ordinary General Public License therefore permits such
linking only if the entire combination fits its criteria of freedom.
The Lesser General Public License permits more lax criteria
for linking other code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than the
ordinary General Public License. It also provides other free
software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries.
However, the Lesser license provides advantages in certain
special circumstances.
Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software to make sure the
software is free for all its users.
Download from Www.Somanuals.com. All Manuals Search And Download.
For example, on rare occasions, there may be a special need
to encourage the widest possible use of a certain library, so
that it becomes a de-facto standard. To achieve this, non-
free programs must be allowed to use the library. A more
frequent case is that a free library does the same job as
widely used non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we
use the Lesser General Public License.
In other cases, permission to use a particular library in non-
free programs enables a greater number of people to use a
large body of free software. For example, permission to use
the GNU C Library in non-free programs enables many more
people to use the whole GNU operating system, as well as
its variant, the GNU/ Linux operating system.
Although the Lesser General Public License is Less protective
of the users’ freedom, it does ensure that the user of a
program that is linked with the Library has the freedom and
the wherewithal to run that program using a modified version
of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the difference
between a “work based on the library” and a “work that
uses the library”. The former contains code derived from the
library, whereas the latter must be combined with the library
in order to run.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work under
the terms of Section 1 above, provided that you also meet
all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the date of
any change. c) You must cause the whole of the work to be
licensed at no charge to all third parties under the terms of
this License. d) If a facility in the modified Library refers to a
function or a table of data to be supplied by an application
program that uses the facility, other than as an argument
passed when the facility is invoked, then you must make a
good faith effort to ensure that, in the event an application
does not supply such function or table, the facility still
operates, and performs whatever part of its purpose remains
meaningful. (For example, a function in a library to compute
square roots has a purpose that is entirely well-defined
independent of the application. Therefore, Subsection 2d
requires that any application-supplied function or table used
by this function must be optional: if the application does
not supply it, the square root function must still compute
square roots.) These requirements apply to the modified
work as a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably considered
independent and separate works in themselves, then this
License, and its terms, do not apply to those sections
when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a
work based on the Library, the distribution of the whole must
be on the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and
every part regardless of who wrote it.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software functions and/
or data prepared so as to be conveniently linked with
application programs (which use some of those functions
and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms. A
“work based on the Library” means either the Library or any
derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or
with modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included without
limitation in the term “modification”.)
“Source code” for a work means the preferred form of the
work for making modifications to it. For a library, complete
source code means all the source code for all modules it
contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the
library.
Activities other than copying, distribution and modification are
not covered by this License; they are outside its scope. The
act of running a program using the Library is not restricted,
and output from such a program is covered only if its
contents constitute a work based on the Library (independent
of the use of the Library in a tool for writing it). Whether that
is true depends on what the Library does and what the
program that uses the Library does.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of
derivative or collective works based on the Library.
In addition, mere aggregation of another work not based
on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium does
not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the
notices that refer to this License, so that they refer to the
ordinary GNU General Public License, version 2, instead
of to this License. (If a newer version than version 2 of the
ordinary GNU General Public License has appeared, then
you can specify that version instead if you wish.) Do not
make any other change in these notices.
Once this change is made in a given copy, it is irreversible
for that copy, so the ordinary GNU General Public License
applies to all subsequent copies and derivative works made
from that copy.
This option is useful when you wish to copy part of the code
of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided t hat you accompany it with the complete
corresponding machine-readable source code, which
must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software
interchange.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of
any warranty; and distribute a copy of this License along
with the Library.
Download from Www.Somanuals.com. All Manuals Search And Download.
If distribution of object code is made by offering access to copy
from a designated place, then offering equivalent access to copy
the source code from the same place satisfies the requirement
to distribute the source code, even though third parties are not
compelled to copy the source along with the object code.
c) Accompany the work with a written offer, valid for at least
three years, to give the same user the materials specified
in Subsection 6a, above, for a charge no more than the
cost of performing this distribution.
d) If distribution of the work is made by offering access to
copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
5. A program that contains no derivative of any portion of
the Library, but is designed to work with the Library by
being compiled or linked with it, is called a “work that uses
the Library”. Such a work, in isolation, is not a derivative
work of the Library, and therefore falls outside the scope
of this License.
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses
the Library” must include any data and utility programs
needed for reproducing the executable from it. However,
as a special exception, the materials to be distributed need
not include anything that is normally distributed (in either
source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the
executable runs, unless that component itself accompanies
the executable.
However, linking a “work that uses the Library” with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the Library), rather
than a “work that uses the library”.
The executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a
header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though
the source code is not. Whether this is true is especially
significant if the work can be linked without the Library, or if
the work is itself a library. The threshold for this to be true is
not precisely defined by law.
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally
accompany the operating system. Such a contradiction
means you cannot use both them and the Library together in
an executable that you distribute.
7. You may place library facilities that are a work based on
the Library side-by-side in a single library together with
other library facilities not covered by this License, and
distribute such a combined library, provided that the
separate distribution of the work based on the Library and
of the other library facilities is otherwise permitted, and
provided that you do these two things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with any
other library facilities. This must be distributed under the
terms of the Sections above.
b) Give prominent notice with the combined library of the
fact that part of it is a work based on the Library, and
explaining where to find the accompanying uncombined
form of the same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void,
and will automatically terminate your rights under this
License. However, parties who have received copies,
or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full
compliance.
If such an object file uses only numerical parameters, data
structure layouts and accessors, and small macros and small
inline functions (ten lines or less in length), then the use of the
object file is unrestricted, regardless of whether it is legally
a derivative work. (Executables containing this object code
plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may
distribute the object code for the work under the terms of
Section 6. Any executables containing that work also fall
under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification of the
work for the customer’s own use and reverse engineering
for debugging such modifications.
You must give prominent notice with each copy of the work
that the Library is used in it and that the Library and its use
are covered by this License. You must supply a copy of this
License. If the work during execution displays copyright
notices, you must include the copyright notice for the Library
among them, as well as a reference directing the user to the
copy of this License. Also, you must do one of these things:
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying or
distributing the Library (or any work based on the Library),
you indicate your acceptance of this License to do so,
and all its terms and conditions for copying, distributing or
modifying the Library or works based on it.
a) Accompany the work with the complete corresponding
machine-readable source code for the Library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete
machine readable “work that uses the Library”, as object
code and/or source code, so that the user can modify the
Library and then relink to produce a modified executable
containing the modified Library. (It is understood that
the user who changes the contents of definitions files in
the Library will not necessarily be able to recompile the
application to use the modified definitions.)
10. Each time you redistribute the Library (or any work based
on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link
with or modify the Library subject to these terms and
conditions. You may not impose any further restrictions
on the recipients’
b) Use a suitable shared library mechanism for linking with
the Library. A suitable mechanism is one that
exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties
with this License.
(1) uses at run time a copy of the library already present
on the user’s computer system, rather than copying library
functions into the executable, and (2) will operate properly
with a modified version of the library, if the user installs one,
as long as the modified version is interface-compatible with
the version that the work was made with.
11. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether
Download from Www.Somanuals.com. All Manuals Search And Download.
by court order, agreement or otherwise) that contradict
the conditions of this License, they do not excuse
you from the conditions of this License. If you cannot
distribute so as to satisfy simultaneously your obligations
under this License and any other pertinent obligations,
then as a consequence you may not distribute the
Library at all. For example, if a patent license would not
permit royalty free redistribution of the Library by all those
who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License
would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended
to apply in other circumstances.
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system which is implemented by public license practices.
Many people have made generous contributions to the
wide range of software distributed through that system in
reliance on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.
END OF TERMS AND CONDITIONS
This section is intended to make thoroughly clear what is
How to Apply These Terms to Your New Libraries
believed to be a consequence of the rest of this License.
If you develop a new library, and you want it to be of the
greatest possible use to the public, we recommend making it
free software that everyone can redistribute and change. You
can do so by permitting redistribution under these terms (or,
alternatively, under the terms of the ordinary General Public
License).
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty;
and each file should have at least the “copyright” line and a
pointer to where the full notice is found. one line to give the
library’s name and an idea of what it does.
13. The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If the
Library specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.
Copyright (C) year name of author
This library is free software; you can redistribute it and/ or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation;
either version 2.1 of the License, or (at your option) any later
version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301 USA Also add information on how
to contact you by electronic and paper mail.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the library, if necessary. Here is a sample; alter
the names:
14. If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
Yoyodyne, Inc., hereby disclaims all copyright interest in the
library ‘Frob’ (a library for tweaking knobs) written by James
Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.
15. BECAUSE THE LIBRARY IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE LIBRARY
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
Download from Www.Somanuals.com. All Manuals Search And Download.
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights
reserved. Redistribution and use in source and binary forms,
with or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the copyright
notice, this list of conditions and the following disclaimer.
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment:
“This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit. (http://
www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products derived
from this software without prior written permission.
For written permission, please contact openssl-core@
openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
“This product includes cryptographic software written
by Eric Young (eay@ cryptsoft.com)” The word
‘cryptographic’ can be left out if the rouines from the
library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you
must include an acknowledgement: “This product includes
software written by Tim Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS
IS AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE. This product includes cryptographic
software written by Eric Young ([email protected]). This
product includes software written by Tim Hudson(tjh@
cryptsoft.com).
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e.
this code cannot simply be copied and put under another
distribution licence [including the GNU Public Licence.]
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft. com)
All rights reserved. This package is an SSL implementation
written by Eric Young (eay@cryptsoft. com). The
implementation was written so as to conform with Netscapes
SSL. This library is free for commercial and non-commercial
use as long as the following conditions are aheared to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with this
distribution is covered by the same copyright terms except
that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed. If this package
is used in a product, Eric Young should be given attribution
as the author of the parts of the library used. This can be
in the form of a textual message at program startup or in
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types
of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should
not be disposed of with other household waste at the end of their working life. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the
reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances
can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types
of waste and recycle them through your local, free battery return system.
Download from Www.Somanuals.com. All Manuals Search And Download.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
SAMSUNG TECHWIN EUROPE LTD.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
Download from Www.Somanuals.com. All Manuals Search And Download.
|