SCC-C4253P
SCC-C4353P
SCC-C4255P
SCC-C4355P
Power Zoom Camera
User Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
1
2009-9-10 13:53:4
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire
or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such
case, immediately disconnect the power source and contact the service center.
Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (SAMSUNG is not liable for
problems caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a
location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power
and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting
to do so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as
this may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at
any time.
10. When using the camera outdoors, moisture may occur inside the camera due
to temperature difference between indoors and outdoors. For this reason, it is
recommended to install the camera indoors. For outdoor use, use the camera with
built-in fan and heater.
English _ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
3
2009-9-10 13:53:4
overview
FCC STATEmENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may
cause undesired operation.
Caution
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
ꢂ_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
4
2009-9-10 13:53:4
ImPORTANT SAFETy INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
English _ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
5
2009-9-10 13:53:4
overview
CONTENTS
5
6
7
8
8
Important Safety Instructions
Contents
Features
What’s Included
At a Glance
OvERvI2EW
12
12
Preparing Installation
Installation
INSTALLATION &
CONNE1CT2ION
15
16
18
27
29
30
31
32
32
33
Main Menu
Profile
Camera Set
Intelligent Video
Privacy Zone
Preset
SETUP
15
Other Set
Communication
System Info
Language
34
35
Shortcut Keys
Specifications
AP3PEN4DIx
ꢄ_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
6
2009-9-10 13:53:4
FEATURES
With the state-of-the-art digital signal processing technology, full digital image
processing and special algorithm of 600-line high resolution implemented.
High Sensitivity: It implements images of high sensitivity using the up-to-date
Super-HAD IT CCD(SCC-C4253P/C4353P)/ExView-HAD PS CCD(SCC-C4255P/
C4355P).
VPS(Virtual Progressive Scan): This is an advanced technology that reproduces
a sharp progressive image. This is appropriate to high quality recording and file
transfer via the Internet. (SCC-C4255P/C4355P only)
High performance surveillance camera, equipped with x43 zoom lens and digital
zoom IC, enabling monitoring up to 688 times
WDR extends the contrast range as it takes a picture of each of dark and bright areas
before compositing the two, which is useful if you take a picture of windows inside
a building. Namely, it improves the picture quality of the outdoor scenery as well as
indoor.(SCC-C4255P/C4355P only)
Low Illumination: It uses the digital signal technologies such as low illumination and
Day/Night functions that make your camera identify objects even in the worst envi-
ronment.
XDR (eXtended Dynamic Range): Actively controls the gamma compensation in the
way it operates the ambient luminance contrast in a certain pixel unit to determine
the optimal visibility.
Digital Power Synchronization: The full digital Line Lock function directly adjusts the
vertical camera synchronization to enhance the operationability and reliability of this
camera.(SCC-C4353P/C4355P only)
DAY/NIGHT: This function can make the IR Cut filtering function inactive under the illumina-
tion below the normal value.
White Balance to control the brightness to the illumination
Superior Backlight Adjustment:When an object has a bright illumination or sunlight
behind it, this camera automatically improves the shaded object picture quality.
Auto Focus to automatically adjust the focus to the subject movement
Privacy zone to hide a specific area for personal privacy.
English _ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
7
2009-9-10 13:53:4
overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Camera Holder
(Mount Adaptor)
2 Screws
Camera
User's Manual
AT A GLANCE
SIDE vIEW
Mount Adapter
Fixing Grooves
Camera Lens
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you
have applied ethanol.
M
ꢆ_ overview
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
8
2009-9-10 13:53:4
Rear Panel
SCC-C4353P
SCC-C4355P
�
�
�
�
�
�
�
�
�
�
�
�
SCC-C4253P
SCC-C4255P
�
�
�
�
�
�
�
�
�
�
�
�
Input/Output Connector
This connector has input and output ports for RS-485 control signals,
DAY/NIGHT switching, and alarm output signals.
SCC-C4255P/C4355P
SCC-C4253P/C4353P
English _ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd
9
2009-9-10 13:53:4
overview
1. ALARM OUT
Alarm out jack for motion detection. (Open Collector, On Gnd)
2. GND
Grounding jack.
3. TRIGGER IN (SCC-C4255P/C4355P)
Displays the current still image when it receives the Trigger signal. (Normal
Open Type)
4.5.6 FOCUS, COM, ZOOM
This port is used for ZOOM/FOCUS, MENU CONTROL, HOME
RETURN, and ONEAF by using an external controller.
Depending on the input condition, 4 modes, A, B, C, and D are
available. (SPECIAL - CTRL TYPE)
(Operation Voltage Range : +3V~+13V, -3V~-13V)
1) When the voltage is supplied to either ZOOM or FOCUS port
Tele(Up)
Wide(Down)
Near(Left)
Far(Right)
Function
*1
ZOOM Port
FOCUS Port
Code
A
B
C
D
-6V
-6V
+6V
+6V
+6V
-6V
-6V
+6V
-6V
+6V
-6V
+6V
+6V
-6V
+6V
-6V
*1: During MENU OFF, controls ZOOM/FOCUS and during MENU ON,
changes the direction, Up/Down/Left/Right SETUP switch.
2) When the voltage is supplied to both ports
ENTER/AF *2
HOME RETURN *3
Function
ZOOM Port
FOCUS Port
ZOOM Port
FOCUS Port
Code
A
B
C
D
-6V
-6V
+6V
-6V
+6V
-6V
+6V
+6V
-6V
+6V
-6V
+6V
+6V
+6V
-6V
-6V
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 10
2009-9-10 13:53:4
* 2 : For short voltage supply during MENU OFF, executes ONEAF and for
more than 2 second
* 3 : For more than 2 second long voltage supply, moves to the PRESET
0(HOME) position.
7. 5V OUT
Power supply jack for RS-485 JIG. Use within typical DC +5V 100mA.
8. DAY/NIGHT IN
This is a function to receive the external DAY/NIGHT signal from the
sensor(option) and convert the signal into BW.
9. RS-485 DATA-
Jack for connection to RS-485 DATA- signal line.
10. RS-485 DATA+
Jack for connection to RS-485 DATA+ signal line.
SETUP Switch
This switch is used to set the function or property. When this switch is pressed
for at least 2 seconds, the MAIN MENU appears.
(Left/Right) : By pressing this switch left or right, you can move left or right
on the menu or change the displayed value.
(Up/Down) : By pressing this switch up or down, you can move up or down on
the menu.
: When you press this switch in the menu, the selected function is confirmed.
To enter a submenu, press this button.
video OUT Port
This is connected to the Video Input Port of the monitor and it outputs the
Video signals.
GND
This is a grounding port.
Power Connection Port
This is connected to the Power cable.
Power Display LED
When the power is normally connected, the red LED lights.
English _11
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 11
2009-9-10 13:53:4
installation & connection
PREPARING INSTALLATION
To install and use the camera, first prepare the following cables.
Power Adapter Cable (sold separately)
The requirements for the power adapter, which connects to the camera’s
POWER IN terminal, are as follows:
- SCC-C4253P/C4255P : DC 12V 600mA
- SCC-C4353P/C4355P: AC 24V 300mA
DC 12V 600mA
video Cable(sold separately)
Use a BNC cable, such as the one shown below, to connect the camera’s VIDEO
OUT to the monitor.
INSTALLATION
1. Connect one end of the BNC cable(not included) to the VIDEO OUT.
2. Connect the other end of the BNC cable (not included) to the VIDEO IN of the
monitor.
1ꢀ_ installation & connection
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 12
2009-9-10 13:53:4
Video In Terminal of Monitor Rear Surface
BNC cable(not included)
Video Out Terminal
3. Plug in the power adapter(not inlcluded). Use a “minus” screwdriver to connect one
part of the power adapter, which consists of two lines, to the POWER terminal of the
camera as follows :
1.
ALARAM OUT
2. GND
3.
T
R
I
G
G
E
R
I
N
5
.
4.
C
OM
ZOOM
FOC
6.
U
S
7. 5V OUT
8. DA
Y/NIGHT
IN
1
2
3
4
5
6
7
8
+12V
GND
SCC-C4253(P)/C4255(P)
SCC-C4353(P)/C4355(P)
English _1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 13
2009-9-10 13:53:4
installation & connection
4. Determine the type of power supply and set the POWER SELECTION switch
accordingly. Next, plug the power adapter into a wall outlet.
5. If the camera operates normally, the following screen will be displayed for
5 seconds and then disappears.
TYPE
4_ZOM_WDR_P
SAMSUNG
0
RS485,HALF
9600
PROTOCOL
ADDRESS
COMM.TYPE
BAUD RATE
CAMERA VER.
LENS
V1.00_090817
OK
6. The requirements for RS485 control is as follows :
- Signaling Speed: 9600 bps
- Data Bit : 8 bits
- Stop Bit : 1 bit
- Parity Bit : none
1ꢂ_ installation & connection
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 14
2009-9-10 13:53:4
setup
Using OSD icons
_+
:
If these icons appear in the left and right corner of a menu item, you can use
them move to the previous or next menu.
(EXIT): Exits the menu setup screen.
Before exiting the setup screen, select <SAvE> to save your settings
to the whole menus, or <QUIT> to cancel them.
(RET): Saves your settings and returns to the previous screen.
(HOME): Returns to the main menu.
(SAVE): Use this icon if you want to save your settings after you specified the
mask area and privacy area, etc.
Once you saved your settings, the changes remain intact even if you
select <QUIT> on exit.
(DEL): Use this icon if you want to delete a mask, or privacy area, etc.
Once you deleted your settings, the deletions remain valid even if you
select <QUIT> on exit.
: This icon appears in the right of a menu containing sub menu items.
mAIN mENU
This is the first screen you ever see when you turn on the camera where you can set the
camera environment to your needs.
PROFILE
Select a mode appr--opriate to the camera
installation environment.
MAIN MENU
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
CAmERA SET
You can configure the camera settings.
OTHER SET
INTELLIGENCE
Offers motion detection and tracking functions.
COMMUNICATION
SYSTEM INFO
LANGUAGE
PRIvACy ZONE
You can configure the privacy settings.
PRESET
You can set the PRESET POSITION.
OTHER SET
You can reset the camera, or adjust the OSD color to your preference.
English _1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 15
2009-9-10 13:53:4
setup
COmmUNICATION
Configures the settings pertaining to RS-485 communication.
SySTEm INFO
Shows the system information such as the camera version or communication
settings.
LANGUAGE
Select a preferred one from the supported languages.
PROFILE
You can select one from the pre-determined configurations as appropriate to your
specific camera installation environment.
Your selection on each item in PROFILE will affect all other settings of the camera.
STANDARD
Automatically optimizes the camera settings
to the normal environment.
PROFILE
STANDARD
ITS
ITS
BACKLIGHT
DAY/NIGHT
GAMING
This setting enables you to analyze the traffic
situation and take the traffic information at a
glance.
CUSTOM
BACKLIGHT
This setting enables you to view a sharp
background and object even in a severe
backlight scene.
DAy/NIGHT
Automatically optimizes the camera settings to the day and night scene.
GAmING
This automatically configures the settings so that you can work in a stable illumina-
tion condition as indoors.
CUSTOm
Your change to any of the PROFILE settings will switch the display to CUSTOM.
1ꢄ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 16
2009-9-10 13:53:4
CAmERA SETUP mENU
Parent menu Sub-menus
vPS
STANDARD
ITS
BACKLIGHT
DAy/NIGHT
GAmING
OFF
ALC
-
ON
ALC
-
OFF
OFF
ALC
-
OFF
ALC
-
ALC
ALC
-
LEvEL
0
0
0
0
0
BACKLIGHT
OFF
-
OFF
-
WDR
OFF
-
OFF
-
IRIS
WDR
-
MEDIUM
0
WEIGHT Custom Setting Custom Setting
Custom Setting Custom Setting
Custom Setting Custom Setting
WDR LEvEL Custom Setting Custom Setting
WHITE BAL Custom Setting Custom Setting Custom Setting Custom Setting Custom Setting
(F.FAST)
---
(F.FAST)
---
(F.FAST)
---
NORM
SLOW
mOTION
MEDIUM
OFF
MEDIUM
OFF
MEDIUM
OFF
MEDIUM
OFF
MEDIUM
OFF
DNR
SHUTTER
SENSE UP
xDR
AUTO X4
MEDIUM
AUTO
-
AUTO X2
MEDIUM
AUTO
-
AUTO X4
MEDIUM
DAY
AUTO X4
MEDIUM
AUTO
-
AUTO X4
MEDIUM
DAY
NIGHT
BURST
-
-
OFF
OFF
OFF
OFF
ON
-
DAy/NIGHT
ExT
-
-
-
-
BURST
-
DAY
-
-
DAY/NIGHT
-
-
DAY
-
-
DAY/NIGHT
-
-
DAY
-
DAy
mODE
RED
ATW2
ATW1
ATW1
ATW1
ATW1
0
0
0
0
0
BLUE
0
0
0
0
0
WHITE BAL
NIGHT
BRIGHTNESS
mODE
RED
-
-
-
-
-
-
MEDIUM
-
MEDIUM
-
OFF
OFF
OFF
ATW2
ATW2
-
-
-
-
-
-
0
0
2
0
0
2
BLUE
2
2
2
DETAIL
English _1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 17
2009-9-10 13:53:4
setup
CAmERA SET
You can configure the general settings of the camera module.
1. Select <mAIN mENU> - <CAmERA SET>.
The Camera Setup menu appears.
CAMERA SET
CAMERA ID
OFF
OFF
ALC
---
MID
---
VPS
IRIS
MOTION
DNR
SHUTTER
SENS-UP
2. Change the settings as necessary, or select
an item to check.
(F.FAST)
(OFF)
AUTO X4
OFF
FLICKERLESS
XDR
MID
CAmERA ID
Provide the ID and location for a camera that displays on the screen.
1. Select <CAmERA SET> - <CAmERA ID>.
CAMERA ID
ABCDEFGHIJKLMNOPQRSTUVWXYZO
_
▲▼
_+ to select a desired character,
then press [ENTER].
2. Use
123456789 : ?
()/
+
In the lower input box of the screen, the
selected character will be entered.
You can enter up to 54 characters including
SP
-
SP
LOCATION
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
alphabets, numbers and special characters.
LOCATION : Specify the display position
of the camera ID.
3. When done, press [ENTER].
The camera ID will be displayed in the specified position.
vPS
If you set it to <ON>, the camera images will be displayed in progressive mode.
VPS is only available for SCC-C4255P and SCC-C4355P.
M
1ꢆ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 18
2009-9-10 13:53:4
IRIS
The IRIS menu is useful if you set to adjust the
intensity of radiation incoming to the camera.
ALC
[
]
LEVEL
BACKLIGHT
AREA
<SIZE>
<LOCATION>
00
----
I
----
BLC
ALC : Adjust the open and close of the iris.
- LEVEL : Select an overall brightness level.
USER
- BLC : With <BACKLIGHT> set to
<BLC>, you can specify the BLC area.
With AREA set to <USER>, you can
specify the position and size.
- WDR : If you set <BACKLIGHT> to
<WDR>, you will see a menu where you
can set the WDR options.
Specify the shutter speed in WDR LEVEL,
and, the composition level in <WEIGHT>.
Select OUTDOOR, or INDOOR in
<WHITE BAL>.
ALC
[
]
]
LEVEL
BACKLIGHT
WEIGHT
WDR LEVEL
WHITE BAL
00
0
----
----
I
I
----
WDR
MID
[
----
INDOOR
The WDR feature provides an extension of
the gain range, which is useful, especially
if you work on pictures both indoors and
outdoors from inside of a building.
Namely, it improves the sharpness of the picture in outdoor scenery as well as
indoor.
As long as you use the VPS function, the WDR will not be available as the CCD read
method differs accordingly. If you set VPS to ON, WDR will be set to <OFF>
accordingly.
M
WDR is only available for SCC-C4255P
and SCC-C4355P.
MANUAL
[
]
00 ----I----
LEVEL
MANUAL : Adjust the iris level manually.
The overall brightness target of a camera
will be set to ALC level 0, while the iris
can be adjusted manually.
M
English _1ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 19
2009-9-10 13:53:4
setup
AGC
With this, you can adjust the AGC level of a
camera.
CAMERA SET
CAMERA ID
OFF
OFF
With AGC active, if the signal strength falls
below the standard level, AGC will amplify the
video signal to automatically improve the
sensitivity.
If <SENS-UP> is set to <OFF> or <FIx>
mode, the <mOTION> menu will switch to
<AGC>.
VPS
IRIS
AGC
DNR
ALC
(VERY HIGH)
---
MID
OFF
OFF
OFF
MID
SHUTTER
SENS-UP
FLICKERLESS
XDR
With the USER
(
)
submenu selected, press
[ENTER] to display the corresponding screen.
In this mode, you can select from VERY LOW
to VERY HIGH in 16 levels, enabling deeper, wider choices to your convenience.
With the FIX submenu selected, press [ENTER] to display the corresponding
(
)
screen. In this mode, you can select an individualized mode in 16 levels, regardless of
the brightness.
As long as the DAY/NIGHT menu is set to AUTO in Camera Setup, the AGC menu is
not available.
M
As long as FLICKERLESS is set to ON, the AGC mode is not available.
If you set BACKLIGHT to WDR, the AGC fix mode is not available.
mOTION
You can specify a level of AGC for controlling the camera motion.
This is available only of the SENSE UP menu is set to AUTO.
Select F.FAST if you want to monitor a very fast moving object in a low contrast
scene, and S.SLOW if monitoring a very slow moving, inanimate object in the same
condition.
As long as DAY/NIGHT is set to <AUTO>, the <MOTION> menu is not available.
DNR
Reduces the noise on the camera image.
The higher the level is, the greater the effect is.
Set it to <USER> to specify the level.
ꢀ0_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 20
2009-9-10 13:53:5
SHUTTER
CAMERA SET
CAMERA ID
VPS
OFF
OFF
ALC
---
MID
You can select a fixed fast electronic shutter
speed in 7 options ranging from 1/120 to 1/10k,
which is mostly used to take a picture of a fast
moving object.
IRIS
AGC
DNR
SHUTTER
SENS-UP
FLICKERLESS
XDR
(VERY HIGH)
1/120
(OFF)
(OFF)
---
---
MID
As long as SENSE UP is set to AUTO, FIXED /
FLICKERLESS to ON / BACKLIGHT to WDR, the
SHUTTER menu is not available.
SENS-UP
Automatically senses the darkness level at night or in a low contrast scene, and
extends the accumulation time accordingly; you can select <AUTO> or <FIx> for a
bright and sharp image.
If the SHUTTER menu is set to fixed electronic shutter mode, the SENSE UP menu
will not be available.
M
If FLICKERLESS is set to ON, or BACKLIGHT to WDR, the FIX mode of the SENSE UP
menu is not available.
FLICKERLESS
This will prevent possible screen distortion due to a mismatch between the vertical
sync frequency and the blinking frequency of the lighting; if set to <ON>, the shutter
speed will be fixed to 1/120 second.
If SHUTTER is set to FIX, SENSE UP to FIX, and AGC to FIX, the <FLICKERLESS> menu is
not available.
xDR
This will correct a brightness difference between different scenes for the optimal
visibility by calculating the ambient luminance contrast in a certain unit of pixels.
The higher the value is, the higher the correction level is.
English _ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 21
2009-9-10 13:53:5
setup
DAy/NIGHT
You can specify a recording mode according
to the scene.
DAY/NIGHT
AUTO
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DIGITAL ZOOM
DETAIL
1. Select <CAmERA SET> - <DAy/NIGHT>.
ONEAF
[
]
2
2. Select a screen transition mode according
to the illumination, and set options as
appropriate.
OFF
OFF
[
]
2
V-SYNC
AGC COLOR SUP
(INT)---
MID
DAY : Fixed to DAY mode, regardless of
the scene.
NIGHT : Fixed to NIGHT mode,
regardless of the scene.
If BURST is set to <ON>, the burst signal will be output along with the black-
and-white composite video signal.
AUTO : According to the luminance, this
will switch DAY to NIGHT mode, or vice
AUTO
versa.
BURST
OFF
DAY NIGHT
-
BURST : If set to <OFF>, the burst
signal will not be output in NIGHT mode.
BRIGHTNESS
DWELL TIME
MID
2SEC
NIGHT DAY
-
DAY NIGHT BRIGHTNESS : Specify
the brightness level switching from
COLOR to BW filter.
BRIGHTNESS
DWELL TIME
MASK AREA
MID
5SEC
1
2
Adjusting from HIGH to LOW will cause
to switch the filter in a darker screen.
-
-
DAY NIGHT DWELL TIME : Time
required to determine the filter switch.
NIGHT DAY BRIGHTNESS : Specify the brightness level switching from
BW to COLOR filter. Adjusting from HIGH to LOW will cause to switch the
filter in a darker screen.
-
-
NIGHT DAY DWELL TIME : Time required to determine the filter switch.
MASK AREA : If there exists a bright
spot light source in a night scene, you
can specify the size and position as
MASK AREA
<SIZE>
<LOCATION>
needed.
This will prevent an error in switching
filter, or failure to determine the filter
switch in a night scene where a bright
spot light source exists.
Any excessively bright area in a night
scene will be MASKed.
You can specify MASK 1 and 2 simultaneously.
ꢀꢀ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 22
2009-9-10 13:53:5
If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.
EXT : The interface to an external alarm enables an automatic switch between
DAY and NIGHT mode.
If you use an infrared light source while in AUTO mode, this may cause a failure in
AUTO SWITCH or AUTO FOCUS.
M
WHITE BAL
If you need to adjust the color according to the ambient illumination, you can use
the <WHITE BAL> function.
Illumination is generally referred to as color temperature, which is represented in a
measurement of kelvin (K). Color temperatures for ordinary lighting are as follows:
In the <WHITE BAL> menu, you
can set a mode for correcting the
<WHITE BAL>.
10000K
9000K
8000K
Blue sky
Cloudy
Rainy
- ATW1,2 : If you set the <WHITE
BAL> menu to <ATW1> or
<ATW2> mode, this will monitor
the change of the color temperature
to correct the <WHITE BAL> as
needed.
The following color temperature
ranges are assured in individual
modes:
7000K
6000K
5000K
4000K
3000K
Partly Cloudy
Sunny
Fluorescent lamp
ATW1 : 2500K ~ 9300K (1)
ATW2 : 2000K ~ 10000K
(suitable to sodium light source) (2)
Halogen lamp
2000K
1000K
Candlelight
Tungsten lamp
1 : With <ATW1> mode active in a color temperature environment ranging
beyond between 2500K and 9300K, a proper white balance value may not be
produced; if this is the case, you are recommended to use <ATW2> mode.
2 : With <ATW2> mode active in a mostly single color environment, the display
color and the actual one may differ; so select a mode as appropriate to your
color temperature environment.
English _ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 23
2009-9-10 13:53:5
setup
1. Select <CAmERA SET> - <WHITE BAL>.
2. Select a mode where you set the <WHITE BAL>.
DAY : You can set the RED, and BLUE
value in DAY mode.
WHITE BAL
The screen will be displayed in colors
according to your settings.
DAY/NIGHT
MODE
RED
DAY
AWC
---- ----
[
[
[
]
]
I
00
00
You can set the R-GAIN, and B-GAIN value only
---- ----
BLUE
I
in <AWC> mode.
]
]
R-GAIN
B-GAIN
0064
0064
[
NIGHT : You can set the <WHITE BAL>
according to the ambient illumination.
If NIGHT mode is set to <OFF>, the
<WHITE BAL> will operate in a mode
specified in DAY mode at all times;
otherwise, the screen will switch to a
mode specified in <DAy/NIGHT>.
You can set the RED, BLUE and
BRIGHTNESS value in DAY mode.
The screen will be displayed in colors
according to your settings.
WHITE BAL
DAY/NIGHT
BRIGHTNESS
MODE
RED
BLUE
NIGHT
MID
AWC
---- ----
[
[
]
]
I
00
00
---- ----
I
[
[
]
]
R-GAIN
B-GAIN
0064
0064
3. According to the specified recording mode, select a <WHITE BAL> mode with
necessary options.
ATW1,2 : The camera can automatically adjust the color temperature in real
time, according to the ambient conditions.
(Color temperature range 1: 2500K ~ 9300K, 2 : 2000K ~ 10000K)
AWC : Pressing [ENTER] on a desired item will perform ATW once.
You can set the R-GAIN/B-GAIN value.
3200K : Set the color temperature to 3200K.
5600K : Set the color temperature to 5600K.
-
BRIGHTNESS : Specify a brightness level switching from DAY mode to
NIGHR mode setting.
-
-
-
RED : Adjust the strength of the red color.
BLUE : Adjust the strength of the blue color.
R-GAIN/B-GAIN : Specify the current color temperature manually.
ꢀꢂ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 24
2009-9-10 13:53:5
FOCUS mODE
You can select a focus mode according to the
angle that you adjusted for camera recording.
DAY/NIGHT
AUTO
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DIGITAL ZOOM
DETAIL
- AF : This will monitor the screen continuously
to focus automatically. If you adjust the focus
manually, that will operate the same as in
<mF>. This will also restore focus after the
operation of zoom.
ONEAF
[2]
OFF
X16
[2]
V-SYNC
INT
- ONEAF : Restores focus after the operation
of zoom, and operates the same as in <mF>
unless the operation of zoom is executed.
AGC COLOR SUP
MID
- MF : You can adjust the focus manually.
While you are working on the following objects, <AF> may not work properly.
If this is the case, use <MF> instead.
M
- Very bright object, or dominant object in a dark scene
- Object against the rear side of a moist or dirty glass
- A scene where nearby and distant objects co-exist
- White wall or single-colored object
- Venetian blinds and other horizontally striped objects
ZOOm SPEED
You can adjust the zoom operation speed.
DISPLAy ZOOm
You can set to display the zoom status on the screen.
It will disappear in about 3 seconds if the zoom factor has no further change.
DIGITAL ZOOm
You can set the maximum allowable digital zoom ratio.
Digital Zoom will start operation after it is zoomed in to the maximum optical ratio of
x43. If you set DIGITAL ZOOM to x16, you can take a shot at up to x688 (43x16).
When you set DISPLAY ZOOM as on, you may see zoom value on the screen.
DETAIL
Used to adjust the vertical and horizontal distinction, respectively.
English _ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 25
2009-9-10 13:53:5
setup
v-SyNC
You can set the V-SYNC mode.
- If you select <INT>, the camera will use the internal synchronization.
- If selecting <LINE>, the camera will use an external power frequency for
synchronization. The LL-PHASE can be adjusted as appropriate.
It’s a must to use AC 24V power supply when you select line lock for SCC-C4353P and
SCC-C4355P.
M
Line lock is not available for SCC-C4253P and SCC-C4255P.
AGC COLOR SUP
DAY/NIGHT
AUTO
You can adjust the color reproduction range
according to AGC.
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DIGITAL ZOOM
DETAIL
ONEAF
[2]
OFF
X16
REvERSE
[2]
You can reverse the video signal from left
to right, upside down, or vice versa to your
convenience.
V-SYNC
AGC COLOR SUP
INT
MID
POSI/NEGA
You can set the video brightness signal to normal or reverse.
PIP
You can view a main image with a sub image on the same screen.
If more than one PRIVACY ZONE is specified, and PRIVACY SET to <ON>, the PIP
function is not available.
M
As long as SENSE UP is set to FIXED, PIP menu is not available.
According to the luminance, PIP will disappear if the SENSE UP menu is set to AUTO.
DIS
If you set it to <ON> for a camera that is trembled or vibrated from an ambient
change, this will automatically compensate for the flicker on the screen.
If you set <DIS> to <ON>, the image will be enlarged with digital zoom as much
area as compensated.
M
ꢀꢄ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 26
2009-9-10 13:53:5
If you set the digital zoom to a larger ratio than the actual enlargement for
compensation, the <DIS> function will be disabled.
<DIS> may not work properly in the following images:
Flat, i.e., no regular-patterned image / Low contrast scene / High frequency image
taken under a fluorescent lamp / Regular-patterned image.
INTELLIGENT vIDEO
You can enable the motion detection and tracking functions.
1. Select <mAIN mENU>-<INTELLIGENCE>.
2. Select each item and set appropriately.
INTELLIGENCE
MOTION
OFF
OFF
4
ADVANCED
MASK AREA
DISPLAY
1
[
2
3
mOTION
ON
]
SENSITIVITY
RESOLUTION
ALARM OUT
4
You can enable the motion detection and
tracking functions.
[
]
3
If you set it to <DETECTION>, the <FIXED/
MOVED> option of ADVANCED menu will
not be available.
M
In following situations, motion detection and tracking function may not work properly.
- When there is sudden changes of brightness
- When the device moves
- When a certain object’s movement fills most of the framing area
- When there is difficulties in distinguishing the moving object and background
ADvANCED
You can detect motions and mark the video that contains such motion, and
enables tracking of the movement.
Selecting the <FIxED/mOvED> option will mark a region if an existing object
disappears, or a new object appears and fixed for a certain period of time.
In following situations, FIXED/MOVED detection may not work properly.
- When multiple motions continue arbitrarily.
- When the object that is fixed continues to move in the same position.
- When a newly appearing object conceals another object that is moving.
M
English _ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 27
2009-9-10 13:53:5
setup
mASK AREA
MASK AREA
1. Select the number of the area to be
masked that will be excluded from motion
detection.
<SIZE>
<LOCATION>
2. Select the mask number and set the mask
size and its coverage.
DISPLAy
When selected <ON>, it displays the motion detected and detection of configured
advanced function.
SENSITIvITy
Sets the sensitivity of motion sensor.
RESOLUTION
The bigger the resolution setting, the smaller the object that can be detected.
ALARm OUT
ALARM OUT
When selected <ON>, it outputs alarm
signal when the motion is detected and on a
detection of configured advanced function.
MOTION
FIXED/MOVED
ON
ON
ꢀꢆ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 28
2009-9-10 13:53:5
PRIvACy ZONE
You can set up to 12 privacy zones that will be hided for privacy of the subject when
recording.
Zone Setup
1. Select <mAIN mENU>-<PRIvACy ZONE>.
PRIVACY ZONE
2. Select the number of the zone and press
[ENTER].
The Zone setup screen appears.
1
7
2
8
3
9
4
10
5
11
6
12
PRIVACY SET
STYLE
ON
MOSAIC1
3. Select the <ZOOm> and press [ENTER].
▲▼
Using
_+ to locate zoom position.
4. Select the <PIxEL LEvEL>.
Select the pixel level for the SIZE and
LOCATION settings.
5. Select the <SIZE> and press [ENTER].
▲▼
Using
zone.
_+, set the size of the privacy
PRIVACY ZONE SET 1
<ZOOM>
6. Select the <LOCATION> and press
PIXEL LEVEL
<SIZE>
<LOCATION>
[
]
4
[ENTER].
▲▼
Using
_+, set the position of the
privacy zone.
7. Save the changes and move to the
previous screen and select the <STyLE>.
Select the <COLOR> and pick a desired
color.
Setting one or more privacy zone and enabling privacy function will disable the PIP
function.
M
For better privacy protection, make your privacy zone bigger than the required,
bigger by about 30%.
Video portion of mosaic pattern or colored by the privacy zone setup is not
recoverable.
English _ꢀꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 29
2009-9-10 13:53:5
setup
PRESET
This function provides preset camera settings such as zoom and focus so to enable
quicker and easier accessing and monitoring, which supports up to 512 presets.
1. Select <mAIN mENU>-<PRESET>.
MAIN MENU
PROFILE
2. Select the preset number.
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
3. Select <POSITION>.
4. Set <PRESET ID> to <ON> and enter the
name.
OTHER SET
COMMUNICATION
SYSTEM INFO
LANGUAGE
For entering the name, refer to “CAMERA ID”.
(page 18)
PRESET
0
5
H
1
2
7
12
17
22
27
3
4
9
14
19
24
29
6
11
16
21
26
31
8
13
18
23
28
10
15
20
25
30
1/16
HOME RETURN
OFF
PRESET NO. 1
POSITION
PRESET ID
ON
ꢁ0_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 30
2009-9-10 13:53:5
OTHER SET
You can reset the system by running FACTORY DEFAULTS, or set the font color etc.
1. Select <mAIN mENU>-<OTHER SET>.
OTHER SET
2. Select each item and set appropriately.
EXTERNAL TRG
FACTORY DEFAULTS
OSD COLOR
(OFF)---
BW
A
CTRL TYPE
ExTERNAL TRG
Set the EXTERNAL TRG menu to ON and
press the SETUP switch to display the
appropriate screen.
You can set the STILL TIME to 0~4 seconds.
If DELAY TIME is set to FIX, the DELAY TImE
will be set in sync with the STILL TIME; if set
to USER, the DELAY TImE will be set to your
setting.
EXTERNAL TRG
STILL TIME
DELAY TIME
OFF
FIX
If VPS is set to OFF, the EXTERNAL TRG
M
menu will be deactivated.
FACTORy DEFAULTS
When selected, the <FACTORy DEFAULTS>
screen appears and you can reset all settings to
the factory default settings by selecting the <OK>.
However, the protocol, baud rate, address and the
language settings will not be reset.
FACTORY DEFAULTS
OK
CANCEL
Note that the resetting the system to the
factory default will erase all settings data.
M
OSD COLOR
Selects the color of the on-screen display font.
English _ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 31
2009-9-10 13:53:5
setup
CTRL TyPE
By inputting the wire remote port, you may set up the A, B, C or D mode.
Tele
-6V
Wide
+6V
+6V
-6V
Far
+6V
-6V
+6V
-6V
Near
-6V
Code
A
B
C
D
-6V
+6V
-6V
+6V
+6V
-6V
+6V
COmmUNICATION
You can set the RS-485 communications setting in
regard of the camera.
COMMUNICATION
RS485
1. Select <mAIN mENU>-<COmmUNICATION>.
PROTOCOL
BAUD RATE
ADDRESS
SAMSUNG
9600
0
2. Select each item and set appropriately.
3. PROTOCOL, BAUD RATE, ADDRESS :
You can manually set the protocol, baud
rate and address.
SySTEm INFO
You can check the system information.
SYSTEM INFO
1. Select <MAIN MENU>-<SYSTEM INFO>.
_
4
_
_
2. The current system information is
displayed.
TYPE
PROTOCOL
ADDRESS
COMM. TYPE
BAUD RATE
SERIAL NO.
CAMERA VER.
ZOM WDR N
SAMSUNG
0
RS485, HALF
9600
000000000000000
_
v1.00 00000
ꢁꢀ_ setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 32
2009-9-10 13:53:5
LANGUAGE
You can set the language of the user interface.
LANGUAGE
1. Select <mAIN mENU>-<LANGUAGE>.
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
2. Select your language using the up/down
keys.
English _ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 33
2009-9-10 13:53:5
appendix
SHORTCUT KEyS
You may control this camera by using Controller (SSC-5000).
Function
DAY/NIGHT - DAY
Key
[PRESET] + [5] + [1] + [2] + [ENTER]
[PRESET] + [5] + [1] + [3] + [ENTER]
[PRESET] + [5] + [1] + [4] + [ENTER]
[PRESET] + [5] + [1] + [5] + [ENTER]
[PRESET] + [5] + [1] + [6] + [ENTER]
[PRESET] + [5] + [1] + [7] + [ENTER]
[PRESET] + [5] + [1] + [8] + [ENTER]
[PRESET] + [5] + [1] + [9] + [ENTER]
[PRESET] + [5] + [2] + [0] + [ENTER]
[PRESET] + [5] + [2] + [1] + [ENTER]
[PRESET] + [5] + [2] + [2] + [ENTER]
[PRESET] + [5] + [2] + [3] + [ENTER]
[PRESET] + [5] + [2] + [4] + [ENTER]
DAY/NIGHT - NIGHT
DAY/NIGHT - AUTO
DAY/NIGHT - EXT
IRIS – ALC – BACKLIGHT – WDR
CAmERA SET IRIS – ALC – BACKLIGHT – OFF
IRIS - ALC
IRIS - MANU
FOCUS MODE – AF
FOCUS MODE – MF
FOCUS MODE – ONEAF
Resetting (Factory Defaults)
Function
CCD Defect Correction
ꢁꢂ_ appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 34
2009-9-10 13:53:5
SpEcificationS
item
Description
product type
Power Zoom Camera
SCC-C4253P/SCC-C4255P: DC12V
power Source
SCC-C4353P/C4355P : AC 24V(50Hz), DC 12V
SCC-C4253P, SCC-C4255P: 4.2W
SCC-C4353P, SCC-C4355P: 5.6W
power consumption
tV Standard
PAL STANDARD COLOR SYSTEM
SCC-C4255P/C4355P: ExView-HAD PS CCD
SCC-C4253P/C4353P: Super-HAD IT CCD
image Sensor
Effective pixels
752(H) × 582(V)
Horizontal : 15, 625 Hz (INT) / 15, 625 Hz (L/L)
Vertical : 50 Hz (INT) / 50 Hz (L/L)
tV line frequency
Synchronization
Resolution
INT/LINE LOCK (LINE LOCK is not available for SCC-C4253P/C4255P)
Horizontal : 600 TV LINES (color)
Vertical : 350 TV LINES
S/n Ratio
Approximately 52 dB
condition
SCC-C4253P/C4353P SCC-C4255P/C4355P
SENS-UP Illumination
Color
2
B/W
0.2
Color
1.2
B/W
0.12
Off
Off
50IRE
30IRE
15IRE
50IRE
30IRE
15IRE
1.2
0.12
0.7
0.07
Minimum subject
illumination
Off
0.6
0.06
0.3
0.03
x512
x512
x512
0.004
0.002
0.001
0.0004
0.0002
0.0001
0.002
0.001
0.0007
0.0002
0.0001
0.00007
English _35
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 35
2009-9-14 11:23:4
appendix
Item
Description
SCC-C4255P/C4355P: x160
WDR
WDR is not available for SCC-C4253P/C4353P.
Signal Output
COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC
x43 Zoom Lens Integrated
Focal length : 3.21 ~ 138.5mm
Aperture : F1.65(Wide) F3.7(Tale)
Lens
- MOD(Minimum Object Distance) : 100mm
High Speed: OFF~1/10K sec
Low Speed: OFF~X512
Electronic shutter
speed
2x ~ 16x
DIGITAL ZOOM
White Balance
ATW1/ATW2/AWC/MANUAL Mode
(3200°K, 5600°K, R/B Gain adjustment)
Operation
Temperature
-10°C~+50°C
~90%
Operation Humidity
Dimensions
SCC-C4253P/C4255P : 59mm x 59.2mm x 124.2mm
SCC-C4353P/C4355P : 59mm x 59.2mm x 154.5mm
(WxHxD)
SCC-C4253P/C4255P: 421g, SCC-C4353P/C4355P: 564g
silver
Weight
Product Color
36_ appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 36
2009-9-11 15:32:4
(Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH.indd 37
2009-9-10 13:53:5
|