Samsung Security Camera SCC C4237P User Guide

SCC-C4237P  
SCC-C4337P  
SCC-C4239P  
SCC-C4339P  
Power Zoom Camera  
User Manual  
imagine the possibilities  
Thanks you for purchasing this Samsung product.  
To receive a more complete service, please visit  
our website  
Download from Www.Somanuals.com. All Manuals Search And Download.  
fire or electric shock.  
8. If any unusual smells or smoke come from the unit, stop using the product. In  
such case, immediately disconnect the power source and contact the service  
center. Continued use in such a condition may cause fire or electric shock.  
9. If this product fails to operate normally, contact the nearest service center.  
Never disassemble or modify this product in any way. (SAMSUNG is not liable  
for problems caused by unauthorized modifications or attempted repair.)  
10. When cleaning, do not spray water directly onto parts of the product. Doing  
so may cause fire or electric shock.  
CAUTION  
1. Do not drop objects on the product or apply strong blows to it. Keep away  
from a location subject to excessive vibration or magnetic interference.  
2. Do not install in a location subject to high temperature (over 50°C), low  
temperature (below -10°C), or high humidity. Doing so may cause fire or  
electric shock.  
3. If you want to relocate the already installed product, be sure to turn off the  
power and then move or reinstall it.  
4. Remove the power plug from the outlet when there is a lighting storm.  
Neglecting to do so may cause fire or damage to the product.  
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.  
6. Install it in a place with good ventilation.  
7. Avoid aiming the camera directly towards extremely bright objects such as  
sun, as this may damage the CCD image sensor.  
8. Apparatus shall not be exposed to dripping or splashing and no objects filled  
with liquids, such as vases, shall be placed on the apparatus.  
9. The Mains plug is used as a disconnect device and shall stay readily operable  
at any time.  
10. When using the camera outdoors, moisture may occur inside the camera due  
to temperature difference between indoors and outdoors. For this reason, it is  
recommended to install the camera indoors. For outdoor use, use the camera  
with built-in fan and heater.  
English _3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the  
manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, or other  
apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug.  
A polarized plug has two blades with one wider than the other. A grounding  
type plug has two blades and a third grounding prong. The wide blade or the  
third prong is provided for your safety. If the provided plug does not fit into  
your outlet, consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table  
specified by the manufacturer, or sold with the apparatus.  
When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
13. Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is required when  
the apparatus has been damaged in any way, such as powersupply cord  
or plug is damaged, liquid has been spilled or objects have fallen into the  
apparatus, the apparatus has been exposed to rain or moisture, does not  
operate normally, or has been dropped.  
Apparatus shall not be exposed to dripping or splashing and no objects  
filled with liquids, such as vases, shall be placed on the apparatus  
4_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
4
5
6
7
7
Important Safety Instructions  
Contents  
Features  
What’s Included  
Part Names and Functions  
OVERVI2EW  
11  
11  
Preparing Installation  
Connecting the Cables  
INSTALLATION &  
CONN1ECT1ION  
14  
15  
17  
26  
28  
29  
30  
31  
31  
32  
Main Menu  
Profile  
Camera Set  
Intelligent Video  
Privacy Zone  
Preset  
SETUP  
14  
Other Set  
Communication  
System Info  
Language  
33  
34  
Shortcut Keys  
Specifications  
AP3PEN3DIX  
English _5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
FEATURES  
With the state-of-the-art digital signal processing technology, full digital image  
processing and special algorithm of 600-line high resolution implemented.  
High Sensitivity: It implements images of high sensitivity using the up-to-date Super-  
HAD IT CCD(SCC-C4237P/C4337P)/ExView-HAD PS CCD(SCC-C4239P/C4339P).  
VPS(Virtual Progressive Scan): This is an advanced technology that reproduces a  
sharp progressive image. This is appropriate to high quality recording and file transfer  
via the Internet. (SCC-C4239P/C4339P only)  
High performance surveillance camera, equipped with x34 zoom lens and digital  
zoom IC, enabling monitoring up to 544 times  
WDR extends the contrast range as it takes a picture of each of dark and bright areas  
before compositing the two, which is useful if you take a picture of windows inside  
a building. Namely, it improves the picture quality of the outdoor scenery as well as  
indoor.(SCC-C4239P/C4339P only)  
Low Illumination: It uses the digital signal technologies such as low illumination  
and Day/Night functions that make your camera identify objects even in the worst  
environment.  
XDR (eXtended Dynamic Range): Actively controls the gamma compensation in the  
way it operates the ambient luminance contrast in a certain pixel unit to determine  
the optimal visibility.  
Digital Power Synchronization: The full digital Line Lock function directly adjusts the  
vertical camera synchronization to enhance the operationability and reliability of this  
camera.(SCC-C4337P/C4339P only)  
DAY/NIGHT: This function can make the IR Cut filtering function inactive under the  
illumination below the normal value.  
White Balance to control the brightness to the illumination  
Superior Backlight Adjustment:When an object has a bright illumination or sunlight  
behind it, this camera automatically improves the shaded object picture quality.  
Auto Focus to automatically adjust the focus to the subject movement  
Privacy zone to hide a specific area for personal privacy.  
6_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHAT’S INCLUDED  
Please check if your camera and accessories are all included in the product package.  
Camera Holder  
(Mount Adaptor)  
2 Screws  
Camera  
User's Manual  
PART NAMES AND FUNCTIONS  
SIDE VIEW  
Mount Adapter  
Fixing Grooves  
Camera Lens  
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have  
M
applied ethanol.  
English _7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
Rear Panel  
SCC-C4337P  
SCC-C4339P  
SCC-C4237P  
SCC-C4239P  
Input/Output Connector  
This connector has input and output ports for RS-485 control signals,  
DAY/NIGHT switching, and alarm output signals.  
SCC-C4239P/C4339P  
SCC-C4237P/C4337P  
8_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. ALARM OUT  
Alarm out jack for motion detection. (Open Collector, On Gnd)  
2. GND  
Grounding jack.  
3. TRIGGER IN (SCC-C4239P/C4339P)  
Displays the current still image when it receives the Trigger signal. (Normal  
Open Type)  
4.5.6 FOCUS, COM, ZOOM  
This port is used for ZOOM/FOCUS, MENU CONTROL, HOME  
RETURN, and ONEAF by using an external controller.  
Depending on the input condition, 4 modes, A, B, C, and D are  
available. (SPECIAL - CTRL TYPE)  
(Operation Voltage Range : +3V~+13V, -3V~-13V)  
1) When the voltage is supplied to either ZOOM or FOCUS port  
Tele(Up)  
Wide(Down)  
Near(Left)  
Far(Right)  
Function  
*1  
ZOOM Port  
FOCUS Port  
Code  
A
B
C
D
-6V  
-6V  
+6V  
+6V  
+6V  
-6V  
-6V  
+6V  
-6V  
+6V  
-6V  
+6V  
+6V  
-6V  
+6V  
-6V  
*1: During MENU OFF, controls ZOOM/FOCUS and during MENU ON,  
changes the direction, Up/Down/Left/Right SETUP switch.  
2) When the voltage is supplied to both ports  
ENTER/AF *2  
HOME RETURN *3  
Function  
ZOOM Port  
FOCUS Port  
ZOOM Port  
FOCUS Port  
Code  
A
B
C
D
-6V  
-6V  
+6V  
-6V  
+6V  
-6V  
+6V  
+6V  
-6V  
+6V  
-6V  
+6V  
+6V  
+6V  
-6V  
-6V  
English _9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
* 2 : For short voltage supply during MENU OFF, executes ONEAF and for  
more than 2 second  
* 3 : For more than 2 second long voltage supply, moves to the PRESET  
0(HOME) position.  
7. 5V OUT  
Power supply jack for RS-485 JIG. Use within typical DC +5V 100mA.  
8. DAY/NIGHT IN  
This is a function to receive the external DAY/NIGHT signal from the  
sensor(option) and convert the signal into BW.  
9. RS-485 DATA-  
Jack for connection to RS-485 DATA- signal line.  
10. RS-485 DATA+  
Jack for connection to RS-485 DATA+ signal line.  
SETUP Switch  
This switch is used to set the function or property. When this switch is pressed  
for at least 2 seconds, the MAIN MENU appears.  
ef (Left/Right) : By pressing this switch left or right, you can move left or right  
on the menu or change the displayed value.  
cd (Up/Down) : By pressing this switch up or down, you can move up or down on  
the menu.  
: When you press this switch in the menu, the selected function is confirmed.  
To enter a submenu, press this button.  
Video OUT Port  
This is connected to the Video Input Port of the monitor and it outputs the  
Video signals.  
GND  
This is a grounding port.  
Power Connection Port  
This is connected to the Power cable.  
Power Display LED  
When the power is normally connected, the red LED lights.  
10_ installation & connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation & connection  
PREPARING INSTALLATION  
To install and use the camera, rst prepare the following cables.  
POWER ADAPTER CABLE (SOLD SEPARATELY)  
The requirements for the power adapter, which connects to the camera’s  
POWER IN terminal, are as follows:  
- SCC-C4237P/C4239P : DC 12V 600mA  
- SCC-C4337P/C4339P: AC 24V 300mA  
DC 12V 600mA  
VIDEO CABLE(SOLD SEPARATELY)  
Use a BNC cable, such as the one shown below, to connect the camera’s VIDEO  
OUT to the monitor.  
INSTALLATION  
1. Connect one end of the BNC cable(not included) to the VIDEO OUT.  
2. Connect the other end of the BNC cable (not included) to the VIDEO IN of the  
monitor.  
English _11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation & connection  
Video In Terminal of Monitor Rear Surface  
BNC cable(not included)  
Video Out Terminal  
3. Plug in the power adapter(not inlcluded). Use a “minus” screwdriver to connect one  
part of the power adapter, which consists of two lines, to the POWER terminal of the  
camera as follows :  
1.  
ALARAM  
2. GND  
OUT  
3.  
4.  
TRIGG  
FOCUSER IN  
5.  
6.  
COM  
ZOO  
7. 5V  
O
M
UT  
8.  
D
A
Y/NI  
GH  
T
I
N
1
2
3
4
5
6
7
8
+12V  
GND  
SCC-C4237(P)/C4239(P)  
SCC-C4337(P)/C4339(P)  
12_ installation & connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Determine the type of power supply and set the POWER SELECTION switch  
accordingly. Next, plug the power adapter into a wall outlet.  
5. If the camera operates normally, the following screen will be displayed for  
5 seconds and then disappears.  
SYSTEM INFO  
TYPE  
4_34 ZOM_WDR_P  
SAMSUNG  
0
PROTOCOL  
ADDRESS  
COMM.TYPE  
BAUD RATE  
CAMERAA VER.  
LENS  
RS485,HALF  
9600  
V1.00__090817  
OK  
6. The requirements for RS485 control is as follows :  
- Signaling Speed: 9600 bps  
- Data Bit : 8 bits  
- Stop Bit : 1 bit  
- Parity Bit : none  
English _13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
Using OSD icons  
:
If these icons appear in the left and right corner of a menu item, you can use  
them move to the previous or next menu.  
◄►  
(EXIT): Exits the menu setup screen.  
Before exiting the setup screen, select <SAVE> to save your settings  
to the whole menus, or <QUIT> to cancel them.  
(RET): Saves your settings and returns to the previous screen.  
(HOME): Returns to the main menu.  
(SAVE): Use this icon if you want to save your settings after you specified the  
mask area and privacy area, etc.  
Once you saved your settings, the changes remain intact even if you  
select <QUIT> on exit.  
(DEL): Use this icon if you want to delete a mask, or privacy area, etc.  
Once you deleted your settings, the deletions remain valid even if you  
select <QUIT> on exit.  
: This icon appears in the right of a menu containing sub menu items.  
MAIN MENU  
This is the first screen you ever see when you turn on the camera where you can set the  
camera environment to your needs.  
PROFILE  
Select a mode appr--opriate to the camera  
installation environment.  
ꢂ  
ꢂ  
MAIN MENU  
PROFILE  
CAMERRA SET  
INTELLIGENCE  
PRIVACY ZONE  
PRESET  
CAMERA SET  
You can configure the camera settings.  
OTHER SET  
INTELLIGENCE  
Offers motion detection and tracking functions.  
COMMUNICCATION  
SYSTEM INFO  
LANGUAGE  
PRIVACY ZONE  
You can configure the privacy settings.  
PRESET  
You can set the PRESET POSITION.  
OTHER SET  
You can reset the camera, or adjust the OSD color to your preference.  
14_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMMUNICATION  
Configures the settings pertaining to RS-485 communication.  
SYSTEM INFO  
Shows the system information such as the camera version or communication  
settings.  
LANGUAGE  
Select a preferred one from the supported languages.  
PROFILE  
You can select one from the pre-determined configurations as appropriate to your  
specific camera installation environment.  
Your selection on each item in PROFILE will affect all other settings of the camera.  
STANDARD  
Automatically optimizes the camera  
settings to the normal environment.  
W
X
PROFILE  
STANDARD  
ITS  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
This setting enables you to analyze  
the traffic situation and take the traffic  
information at a glance.  
CUSTOM  
BACKLIGHT  
This setting enables you to view a sharp  
background and object even in a severe  
backlight scene.  
DAY/NIGHT  
Automatically optimizes the camera settings to the day and night scene.  
GAMING  
This automatically configures the settings so that you can work in a stable  
illumination condition as indoors.  
CUSTOM  
Your change to any of the PROFILE settings will switch the display to CUSTOM.  
English _15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
CAMERA SETUP MENU  
Parent Menu Sub-menus  
VPS  
STANDARD  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
OFF  
ALC  
-
ON  
ALC  
-
OFF  
OFF  
ALC  
-
OFF  
ALC  
-
ALC  
ALC  
-
LEVEL  
0
0
0
0
0
BACKLIGHT  
OFF  
-
OFF  
-
WDR  
OFF  
-
OFF  
-
IRIS  
WDR  
-
MEDIUM  
0
WEIGHT Custom Setting Custom Setting  
Custom Setting Custom Setting  
Custom Setting Custom Setting  
WDR LEVEL Custom Setting Custom Setting  
WHITE BAL Custom Setting Custom Setting Custom Setting Custom Setting Custom Setting  
(F.FAST)  
---  
(F.FAST)  
---  
(F.FAST)  
---  
NORM  
SLOW  
MOTION  
MEDIUM  
MEDIUM  
MEDIUM  
MEDIUM  
MEDIUM  
DNR  
SHUTTER  
SENSE UP  
XDR  
OFF  
OFF  
OFF  
OFF  
OFF  
AUTO X4  
AUTO X2  
AUTO X4  
AUTO X4  
AUTO X4  
MEDIUM  
MEDIUM  
MEDIUM  
MEDIUM  
MEDIUM  
AUTO  
AUTO  
DAY  
AUTO  
DAY  
NIGHT  
BURST  
-
-
-
-
-
OFF  
ON  
OFF  
OFF  
OFF  
DAY/NIGHT  
EXT  
-
-
-
-
-
BURST  
-
-
-
-
-
DAY  
DAY/NIGHT  
DAY  
DAY/NIGHT  
DAY  
DAY  
-
-
-
-
-
MODE  
RED  
ATW2  
ATW1  
ATW1  
ATW1  
ATW1  
0
0
0
0
0
BLUE  
0
0
0
0
0
WHITE BAL  
NIGHT  
BRIGHTNESS  
MODE  
RED  
-
-
-
-
-
-
MEDIUM  
-
MEDIUM  
-
OFF  
ATW2  
OFF  
ATW2  
OFF  
-
-
0
0
2
-
-
0
0
2
-
-
BLUE  
2
2
2
DETAIL  
16_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA SET  
You can configure the general settings of the camera module.  
1. Select <MAIN MENU> - <CAMERA SET>.  
The Camera Setup menu appears.  
W
X
CAMERA SET  
CAMERA ID  
OFF  
OFF  
ALC  
---  
MID  
---  
2. Change the settings as necessary, or  
select an item to check.  
VPS  
IRIS  
MOTION  
DNR  
SHUTTER  
SENS-UP  
(F.FAST)  
(OFF)  
AUTO X4  
OFF  
FLICKERLESS  
XDR  
MID  
CAMERA ID  
Provide the ID and location for a camera that  
displays on the screen.  
CAMERA ID  
ABCDEFGGHIJKLMNNOPQRSTTUVWXYZZO  
_
123456789 : ?  
()/  
+
1. Select <CAMERA SET> - <CAMERA ID>.  
▲▼  
2. Use  
to select a desired character,  
◄►  
then press [ENTER].  
In the lower input box of the screen, the  
selected character will be entered.  
XX WW  
SP  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
SP  
LOCATION  
-
You can enter up to 54 characters including  
alphabets, numbers and special characters.  
LOCATION : Specify the display position of the camera ID.  
3. When done, press [ENTER].  
The camera ID will be displayed in the specified position.  
VPS  
If you set it to <ON>, the camera images will be displayed in progressive mode.  
VPS is only available for SCC-C4239P and SCC-C4339P.  
M
English _17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
IRIS  
The IRIS menu is useful if you set to adjust the  
intensity of radiation incoming to the camera.  
ALC  
[
]
LEVEL  
BACKLLIGHT  
AREA  
<SIZE>  
<LOCATION>  
00  
----  
I
----  
BLC  
ALC : Adjust the open and close of the iris.  
USER  
- LEVEL : Select an overall brightness level.  
- BLC : With <BACKLIGHT> set to  
<BLC>, you can specify the BLC area.  
With AREA set to <USER>, you can spec-  
ify the position and size.  
- WDR : If you set <BACKLIGHT> to  
<WDR>, you will see a menu where you  
can set the WDR options.  
Specify the shutter speed in WDR LEVEL,  
and, the composition level in <WEIGHT>.  
Select OUTDOOR, or INDOOR in  
<WHITE BAL>.  
ALC  
[
]
]
LEVEL  
BACKLIGHT  
WEIGHT  
WDR LEVEL  
WHITE BAL  
00  
0
----  
----  
I
I
----  
WDR  
MID  
[
----  
INDOOR  
The WDR feature provides an extension of  
the gain range, which is useful, especially  
if you work on pictures both indoors and  
outdoors from inside of a building.  
Namely, it improves the sharpness of the picture in outdoor scenery as well as  
indoor.  
As long as you use the VPS function, the WDR will not be available as the CCD read  
M
method differs accordingly. If you set VPS to ON, WDR will be set to <OFF>  
accordingly.  
WDR is only available for SCC-C4239P and SCC-C4339P.  
MANUAL : Adjust the iris level manually.  
MANUAL  
[
]
00 ----I----  
LEVEL  
The overall brightness target of a camera  
will be set to ALC level 0, while the iris can  
be adjusted manually.  
M
18_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AGC  
With this, you can adjust the AGC level of a  
camera.  
With AGC active, if the signal strength falls  
below the standard level, AGC will amplify the  
video signal to automatically improve the  
sensitivity.  
W
X
CAMERRA SET  
CAMERA ID  
OFF  
OFF  
VPS  
IRIS  
AGC  
DNR  
ALC  
(VERY HIGH)  
---  
MID  
OFF  
OFF  
OFF  
MID  
SHUTTER  
SENS-UP  
FLICKERLESS  
XDR  
If <SENS-UP> is set to <OFF> or <FIX>  
mode, the <MOTION> menu will switch to  
<AGC>.  
With the USER  
(
)
submenu selected, press  
[ENTER] to display the corresponding screen.  
In this mode, you can select from VERY LOW  
to VERY HIGH in 16 levels, enabling deeper, wider choices to your convenience.  
With the FIX submenu selected, press [ENTER] to display the corresponding  
(
)
screen. In this mode, you can select an individualized mode in 16 levels, regardless of  
the brightness.  
As long as the DAY/NIGHT menu is set to AUTO in Camera Setup, the AGC menu is  
M
not available.  
As long as FLICKERLESS is set to ON, the AGC mode is not available.  
If you set BACKLIGHT to WDR, the AGC fix mode is not available.  
MOTION  
You can specify a level of AGC for controlling the camera motion.  
This is available only of the SENSE UP menu is set to AUTO.  
Select F.FAST if you want to monitor a very fast moving object in a low contrast  
scene, and S.SLOW if monitoring a very slow moving, inanimate object in the same  
condition.  
As long as DAY/NIGHT is set to <AUTO>, the <MOTION> menu is not available.  
DNR  
Reduces the noise on the camera image.  
The higher the level is, the greater the effect is.  
Set it to <USER> to specify the level.  
English _19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
SHUTTER  
You can select a fixed fast electronic shutter  
speed in 7 options ranging from 1/120 to 1/10k,  
which is mostly used to take a picture of a fast  
moving object.  
W
X
CAMERRA SET  
CAMERA ID  
OFF  
OFF  
ALC  
---  
MID  
VPS  
IRIS  
AGC  
DNR  
(VERY HIGH)  
As long as SENSE UP is set to AUTO, FIXED /  
FLICKERLESS to ON / BACKLIGHT to WDR, the  
SHUTTER menu is not available.  
SHUTTER  
SENS-UP  
FLICKERLESS  
XDR  
1/120  
(OFF)  
(OFF)  
---  
---  
MID  
SENS-UP  
Automatically senses the darkness level at night or in a low contrast scene, and  
extends the accumulation time accordingly; you can select <AUTO> or <FIX> for a  
bright and sharp image.  
If the SHUTTER menu is set to fixed electronic shutter mode, the SENSE UP menu will  
M
not be available.  
If FLICKERLESS is set to ON, or BACKLIGHT to WDR, the FIX mode of the SENSE UP  
menu is not available.  
FLICKERLESS  
This will prevent possible screen distortion due to a mismatch between the vertical  
sync frequency and the blinking frequency of the lighting; if set to <ON>, the shutter  
speed will be fixed to 1/120 second.  
If SHUTTER is set to FIX, SENSE UP to FIX, and AGC to FIX, the <FLICKERLESS> menu is not  
available.  
XDR  
This will correct a brightness difference between different scenes for the optimal  
visibility by calculating the ambient luminance contrast in a certain unit of pixels.  
The higher the value is, the higher the correction level is.  
20_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
DAY/NIGHT  
You can specify a recording mode according  
to the scene.  
DAY/NIGHT  
AUTO  
WHITE BAL  
FOCUS MODE  
ZOOM SPEED  
DISPLAY ZOOM  
DIGITAL ZOOM  
DETAIL  
1. Select <CAMERA SET> - <DAY/NIGHT>.  
ONEAF  
[ ]  
2
2. Select a screen transition mode according  
to the illumination, and set options as  
appropriate.  
OFF  
OFF  
[ ]  
2
V-SYNC  
AGC COLOR SUP  
(INT)---  
MID  
DAY : Fixed to DAY mode, regardless of  
the scene.  
NIGHT : Fixed to NIGHT mode,  
regardless of the scene.  
If BURST is set to <ON>, the burst signal will be output along with the black-  
and-white composite video signal.  
AUTO : According to the luminance, this  
will switch DAY to NIGHT mode, or vice  
AUTO  
versa.  
BURST  
OFF  
¨
DAY NIGHT  
-
BURST : If set to <OFF>s, the burst sig-  
nal will not be output in NIGHT mode.  
BRIGHTTNESS  
DWELL TIME  
MID  
2SEC  
¨
NIGHT DAY  
-
DAY NIGHT  
BRIGHTNESS  
:
¨
BRIGHTTNESS  
DWELL TIME  
MASK AREA  
MID  
5SEC  
Specify the brightness level switch-  
ing from COLOR to BW filter.  
Adjusting from HIGH to LOW will cause  
to switch the filter in a darker screen.  
1
2
-
-
DAY NIGHT DWELL TIME : Time re-  
quired to determine the filter switch.  
¨
NIGHT DAY BRIGHTNESS : Specify the brightness level switching from  
¨
BW to COLOR filter. Adjusting from HIGH to LOW will cause to switch the  
filter in a darker screen.  
-
-
NIGHT DAY DWELL TIME : Time required to determine the filter switch.  
¨
MASKAREA:Ifthereexistsabrightspot  
light source in a night scene, you can  
specify the size and position as needed.  
MASK AREA  
<SIZE>  
<LOCATION>  
This will prevent an error in switch-  
ing filter, or failure to determine the  
filter switch in a night scene where  
a bright spot light source exists.  
Any excessively bright area in a night  
scene will be MASKed.  
Youcan specify MASK 1 and 2 simultaneously.  
English _21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.  
EXT : The interface to an external alarm enables an automatic switch between  
DAY and NIGHT mode.  
If you use an infrared light source while in AUTO mode, this may cause a failure in  
M
AUTO SWITCH or AUTO FOCUS.  
WHITE BAL  
If you need to adjust the color according to the ambient illumination, you can use the  
<WHITE BAL> function.  
Illumination is generally referred to as color temperature, which is represented in a  
measurement of kelvin (K). Color temperatures for ordinary lighting are as follows:  
In the <WHITE BAL> menu, you can  
10000K  
9000K  
8000K  
Blue sky  
Cloudy  
set a mode for correcting the <WHITE  
Rainy  
BAL>.  
- ATW1,2 : If you set the <WHITE  
BAL> menu to <ATW1> or  
<ATW2> mode, this will monitor  
the change of the color temperature  
to correct the <WHITE BAL> as  
needed.  
The following color temperature  
ranges are assured in individual  
modes:  
7000K  
6000K  
5000K  
4000K  
3000K  
Partly Cloudy  
Sunny  
Fluorescent lamp  
Halogen lamp  
ATW1 : 2500K ~ 9300K ( 1)  
2000K  
1000K  
ATW2 : 2000K ~ 10000K  
Candlelight  
Tungsten lamp  
(suitable to sodium light source) ( 2)  
1 : With <ATW1> mode active in a color temperature environment ranging  
beyond between 2500K and 9300K, a proper white balance value may not be  
produced; if this is the case, you are recommended to use <ATW2> mode.  
2 : With <ATW2> mode active in a mostly single color environment, the display  
color and the actual one may differ; so select a mode as appropriate to your  
color temperature environment.  
22_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Select <CAMERA SET> - <WHITE BAL>.  
2. Select a mode where you set the <WHITE BAL>.  
DAY : You can set the RED, and BLUE  
value in DAY mode.  
WHITE BAL  
The screen will be displayed in colors  
according to your settings.  
DAY/NIGHT  
MODE  
RED  
DAY  
AWC  
---- ----  
[
[
[
]
]
I
00  
00  
You can set the R-GAIN, and B-GAIN  
value only in <AWC> mode.  
---- ----  
BLUE  
I
]
]
R-GAIN  
B-GAIN  
0064  
0064  
[
NIGHT : You can set the <WHITE BAL> according to the ambient  
illumination.  
WHITE BAL  
If NIGHT mode is set to <OFF>, the  
<WHITE BAL> will operate in a mode  
DAY/NIGHT  
BRIGHTNESS  
MODE  
RED  
NIGHT  
MID  
AWC  
I
I
specified in DAY mode at all times;  
otherwise, the screen will switch to a  
mode specified in <DAY/NIGHT>.  
You can set the RED, BLUE and  
BRIGHTNESS value in DAY mode.  
The screen will be displayed in colors  
according to your settings.  
---- ----  
---- ----  
[
[
]
]
00  
00  
BLUE  
[
[
]
]
R-GAIN  
B-GAIN  
0064  
0064  
3. According to the specified recording mode,  
select a <WHITE BAL> mode with necessary options.  
ATW1,2 : The camera can automatically adjust the color temperature in real  
time, according to the ambient conditions.  
(Color temperature range 1: 2500K ~ 9300K, 2 : 2000K ~ 10000K)  
AWC : Pressing [ENTER] on a desired item will perform ATW once.  
You can set the R-GAIN/B-GAIN value.  
3200K : Set the color temperature to 3200K.  
5600K : Set the color temperature to 5600K.  
-
BRIGHTNESS : Specify a brightness level switching from DAY mode to  
NIGHR mode setting.  
-
-
-
RED : Adjust the strength of the red color.  
BLUE : Adjust the strength of the blue color.  
R-GAIN/B-GAIN : Specify the current color temperature manually.  
English _23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
FOCUS MODE  
You can select a focus mode according to the  
angle that you adjusted for camera recording.  
DAY/NIGHT  
AUTO  
WHITE BAL  
FOCUS MODE  
ZOOM SPEED  
DISPLAY ZOOM  
DIGITAL ZOOM  
DETAIL  
- AF : This will monitor the screen continuously  
to focus automatically. If you adjust the focus  
manually, that will operate the same as in  
<MF>. This will also restore focus after the  
operation of zoom.  
ONEAF  
[2]  
OFF  
X16  
[2]  
V-SYNC  
INT  
AGC COLOR SUP  
MID  
- ONEAF : Restores focus after the operation  
of zoom, and operates the same as in <MF>  
unless the operation of zoom is executed.  
- MF : You can adjust the focus manually.  
While you are working on the following objects, <AF> may not work properly.  
If this is the case, use <MF> instead.  
M
- Very bright object, or dominant object in a dark scene  
- Object against the rear side of a moist or dirty glass  
- A scene where nearby and distant objects co-exist  
- White wall or single-colored object  
- Venetian blinds and other horizontally striped objects  
ZOOM SPEED  
You can adjust the zoom operation speed.  
DISPLAY ZOOM  
You can set to display the zoom status on the screen.  
It will disappear in about 3 seconds if the zoom factor has no further change.  
DIGITAL ZOOM  
You can set the maximum allowable digital zoom ratio.  
Digital Zoom will start operation after it is zoomed in to the maximum optical ratio of  
x34. If you set DIGITAL ZOOM to x16, you can take a shot at up to x544 (34x16).  
When you set DISPLAY ZOOM as on, you may see zoom value on the screen.  
DETAIL  
Used to adjust the vertical and horizontal distinction, respectively.  
24_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V-SYNC  
You can set the V-SYNC mode.  
- If you select <INT>, the camera will use the internal synchronization.  
- If selecting <LINE>, the camera will use an external power frequency for  
synchronization. The LL-PHASE can be adjusted as appropriate.  
It’s a must to use AC 24V power supply when you select line lock for SCC-C4337P  
M
and SCC-C4339P.  
Line lock is not available for SCC-C4237P and SCC-C4239P.  
AGC COLOR SUP  
DAY/NIGHT  
AUTO  
You can adjust the color reproduction range  
according to AGC.  
WHITE BAL  
FOCUS MODE  
ZOOM SPEED  
DISPLAY ZOOM  
DIGITAL ZOOM  
DETAIL  
ONEAF  
[2]  
OFF  
X16  
REVERSE  
[2]  
You can reverse the video signal from left  
to right, upside down, or vice versa to your  
convenience.  
V-SYNC  
AGC COLOR SUP  
INT  
MID  
POSI/NEGA  
You can set the video brightness signal to normal or reverse.  
PIP  
You can view a main image with a sub image on the same screen.  
If more than one PRIVACY ZONE is specified, and PRIVACY SET to <ON>, the PIP  
M
function is not available.  
As long as SENSE UP is set to FIXED, PIP menu is not available.  
According to the luminance, PIP will disappear if the SENSE UP menu is set to AUTO.  
DIS  
If you set it to <ON> for a camera that is trembled or vibrated from an ambient  
change, this will automatically compensate for the flicker on the screen.  
If you set <DIS> to <ON>, the image will be enlarged with digital zoom as much  
M
area as compensated.  
English _25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
If you set the digital zoom to a larger ratio than the actual enlargement for  
compensation, the <DIS> function will be disabled.  
<DIS> may not work properly in the following images:  
Flat, i.e., no regular-patterned image / Low contrast scene / High frequency image  
taken under a fluorescent lamp / Regular-patterned image.  
INTELLIGENT VIDEO  
You can enable the motion detection and tracking functions.  
1. Select <MAIN MENU>-<INTELLIGENCE>.  
W
X
INTELLIGENCE  
2. Select each item and set appropriately.  
MOTION  
OFF  
OFF  
4
ADVANCED  
MASK AREA  
DISPLAY  
1
2
3
ON  
[ ]  
4
SENSIITIVITY  
RESOLUTION  
ALARM OUT  
MOTION  
[ ]  
3
You can enable the motion detection and  
tracking functions.  
If you set it to <DETECTION>, the <FIXED/MOVED> option of ADVANCED menu  
M
will not be available.  
In following situations, motion detection and tracking function may not work  
properly.  
- When there is sudden changes of brightness  
- When the device moves  
- When a certain object’s movement fills most of the framing area  
- When there is difficulties in distinguishing the moving object and background  
ADVANCED  
You can detect motions and mark the video that contains such motion, and  
enables tracking of the movement.  
Selecting the <FIXED/MOVED> option will mark a region if an existing object  
disappears, or a new object appears and fixed for a certain period of time.  
In following situations, FIXED/MOVED detection may not work properly.  
M
- When multiple motions continue arbitrarily.  
- When the object that is fixed continues to move in the same position.  
- When a newly appearing object conceals another object that is moving.  
26_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MASK AREA  
MASK AREA  
1. Select the number of the area to be  
masked that will be excluded from motion  
detection.  
<SIZE>  
<LOCATION>  
2. Select the mask number and set the mask  
size and its coverage.  
DISPLAY  
When selected <ON>, it displays the motion detected and detection of configured  
advanced function.  
SENSITIVITY  
Sets the sensitivity of motion sensor.  
RESOLUTION  
The bigger the resolution setting, the smaller the object that can be detected.  
ALARM OUT  
ALARM OUT  
When selected <ON>, it outputs alarm signal  
when the motion is detected and on a detection  
of configured advanced function.  
MOTION  
FIXED/MOVED  
ON  
ON  
English _27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
PRIVACY ZONE  
You can set up to 12 privacy zones that will be hided for privacy of the subject when  
recording.  
Zone Setup  
1. Select <MAIN MENU>-<PRIVACY ZONE>.  
W
X
PRIVACY ZONE  
2. Select the number of the zone and press  
[ENTER].  
1
7
2
8
3
9
4
10  
5
11  
6
12  
The Zone setup screen appears.  
PRIVACY SET  
STYLE  
ON  
MOSAIC1  
3. Select the <ZOOM> and press [ENTER].  
▲▼  
Using  
to locate zoom position.  
◄►  
4. Select the <PIXEL LEVEL>.  
Select the pixel level for the SIZE and  
LOCATION settings.  
5. Select the <SIZE> and press [ENTER].  
▲▼  
Using  
zone.  
, set the size of the privacy  
◄►  
PRIVACY ZONE SET 1  
<ZOOM>  
PIXEL LEVEL  
<SIZE>  
<LOCATION>  
6. Select the <LOCATION> and press  
[ ]  
4
[ENTER].  
▲▼  
Using  
, set the position of the  
◄►  
privacy zone.  
7. Save the changes and move to the  
previous screen and select the <STYLE>.  
Select the <COLOR> and pick a desired  
color.  
Setting one or more privacy zone and enabling privacy function will disable the PIP  
M
function.  
For better privacy protection, make your privacy zone bigger than the required, bigger  
by about 30%.  
Video portion of mosaic pattern or colored by the privacy zone setup is not  
recoverable.  
28_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRESET  
This function provides preset camera settings such as zoom and focus so to enable  
quicker and easier accessing and monitoring, which supports up to 512 presets.  
1. Select <MAIN MENU>-<PRESET>.  
ꢂ  
ꢂ  
MAIN MENU  
PROFILE  
2. Select the preset number.  
3. Select <POSITION>.  
CAMERRA SET  
INTELLIGENCE  
PRIVACY ZONE  
PRESET  
4. Set <PRESET ID> to <ON> and enter the  
name.  
OTHER SET  
For entering the name, refer to “CAMERA ID”.  
COMMUNIICATION  
SYSTEM INFO  
LANGUAGE  
(page 17)  
W
X
PRESET  
0
5
H
1
2
7
12  
17  
22  
27  
3
4
9
14  
19  
24  
29  
6
11  
16  
21  
26  
31  
8
13  
18  
23  
28  
10  
15  
20  
25  
30  
1/16  
W
X
HOME RETURN  
OFF  
PRESET NO. 1  
POSITION  
PRESET ID  
ON  
English _29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
OTHER SET  
You can reset the system by running FACTORY DEFAULTS, or set the font color etc.  
1. Select <MAIN MENU>-<OTHER SET>.  
2. Select each item and set appropriately.  
W
X
OTHER SET  
EXTERNNAL TRG  
FACTORY DEFAULTS  
OSD COLOR  
(OFF)---  
BW  
A
CTRL TYPE  
EXTERNAL TRG  
Set the EXTERNAL TRG menu to ON and  
press the SETUP switch to display the  
appropriate screen.  
You can set the STILL TIME to 0~4 seconds.  
If DELAY TIME is set to FIX, the DELAY TIME  
will be set in sync with the STILL TIME; if set  
to USER, the DELAY TIME will be set to your  
setting.  
EXTERNAL TRG  
STILL TIME  
DELAY TIME  
OFF  
FIX  
If VPS is set to OFF, the EXTERNAL TRG  
M
menu will be deactivated.  
FACTORY DEFAULTS  
When selected, the <FACTORY DEFAULTS>  
screen appears and you can reset all settings to  
the factory default settings by selecting the <OK>.  
However, the protocol, baud rate, address and the  
language settings will not be reset.  
FACTORY DEFAULTS  
OK  
CANCEL  
Note that the resetting the system to the  
M
factory default will erase all settings data.  
OSD COLOR  
Selects the color of the on-screen display font.  
30_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CTRL TYPE  
By inputting the wire remote port, you may set up the A, B, C or D mode.  
Tele  
-6V  
Wide  
+6V  
+6V  
-6V  
Far  
+6V  
-6V  
+6V  
-6V  
Near  
-6V  
Code  
A
B
C
D
-6V  
+6V  
-6V  
+6V  
+6V  
-6V  
+6V  
COMMUNICATION  
You can set the RS-485 communications setting in regard of the camera.  
1. Select <MAIN MENU>-<COMMUNICATION>.  
W
X
COMMUNICATION  
2. Select each item and set appropriately.  
RS485  
3. PROTOCOL, BAUD RATE, ADDRESS :  
You can manually set the protocol, baud  
rate and address.  
PROTOCOL  
BAUD RATE  
ADDRESS  
SAMSUNG  
9600  
0
SYSTEM INFO  
You can check the system information.  
1. Select <MAIN MENU>-<SYSTEM INFO>.  
W
X
SYSTEM INFO  
2. The current system information is  
displayed.  
TYPE  
PROTOCOL  
ADDRESS  
4_34 ZOM_WDR_P  
SAMSUNG  
0
COMM. TYPE  
BAUD RATE  
SERIAL NO.  
CAMERA VER.  
RS485,, HALF  
9600  
0000000000000000  
_
v1.00 00000  
English _31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup  
LANGUAGE  
You can set the language of the user interface.  
1. Select <MAIN MENU>-<LANGUAGE>.  
W
X
LANGUAGE  
2. Select your language using the up/down  
ENGLISH  
keys.  
PУCCKNЙ  
POLSKI  
ČESKY  
TÜRKÇE  
32_ setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
SHORTCUT KEYS  
You may control this camera by using Controller (SSC-5000).  
Function  
DAY/NIGHT - DAY  
Key  
[PRESET] + [5] + [1] + [2] + [ENTER]  
[PRESET] + [5] + [1] + [3] + [ENTER]  
[PRESET] + [5] + [1] + [4] + [ENTER]  
[PRESET] + [5] + [1] + [5] + [ENTER]  
[PRESET] + [5] + [1] + [6] + [ENTER]  
[PRESET] + [5] + [1] + [7] + [ENTER]  
[PRESET] + [5] + [1] + [8] + [ENTER]  
[PRESET] + [5] + [1] + [9] + [ENTER]  
[PRESET] + [5] + [2] + [0] + [ENTER]  
[PRESET] + [5] + [2] + [1] + [ENTER]  
[PRESET] + [5] + [2] + [2] + [ENTER]  
[PRESET] + [5] + [2] + [3] + [ENTER]  
[PRESET] + [5] + [2] + [4] + [ENTER]  
DAY/NIGHT - NIGHT  
DAY/NIGHT - AUTO  
DAY/NIGHT - EXT  
IRIS – ALC – BACKLIGHT – WDR  
CAMERA SET IRIS – ALC – BACKLIGHT – OFF  
IRIS - ALC  
IRIS - MANU  
FOCUS MODE – AF  
FOCUS MODE – MF  
FOCUS MODE – ONEAF  
Resetting (Factory Defaults)  
Function  
CCD Defect Correction  
English _33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
SPECIFICATIONS  
Item  
Description  
Product Type  
Power Source  
Power Zoom Camera  
SCC-C4237P/SCC-C4239P: DC12V  
SCC-C4337P/C4339P : AC 24V(50Hz), DC 12V  
SCC-C4237P, SCC-C4239P: 4.2W  
SCC-C4337P, SCC-C4339P: 5.6W  
Power Consumption  
TV Standard  
PAL STANDARD COLOR SYSTEM  
SCC-C4239P/C4339P: ExView-HAD PS CCD  
SCC-C4237P/C4337P: Super-HAD IT CCD  
Image Sensor  
Effective Pixels  
752(H) × 582(V)  
Horizontal : 15, 625 Hz (INT) / 15, 625 Hz (L/L)  
Vertical : 50 Hz (INT) / 50 Hz (L/L)  
TV line frequency  
Synchronization  
Resolution  
INT/LINE LOCK (LINE LOCK is not available for SCC-C4237P/C4239P)  
Horizontal : 600 TV LINES (color)  
Vertical : 350 TV LINES  
S/N Ratio  
Approximately 52 dB  
condition  
SCC-C4237P/C4337P SCC-C4239P/C4339P  
SENS-UP Illumination  
Color  
2
B/W  
0.2  
Color  
1.2  
B/W  
0.12  
Off  
Off  
50IRE  
30IRE  
15IRE  
50IRE  
30IRE  
15IRE  
1.2  
0.12  
0.7  
0.07  
Minimum  
subject  
illumination  
Off  
0.6  
0.06  
0.3  
0.03  
x512  
x512  
x512  
0.004  
0.002  
0.001  
0.0004  
0.0002  
0.0001  
0.002  
0.001  
0.0007  
0.0002  
0.0001  
0.00007  
34_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Item  
Description  
SCC-C4239P/C4339P: x160  
WDR  
WDR is not available for SCC-C4237P/C4337P.  
Signal Output  
COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC  
x34 Zoom Lens Integrated  
Focal length : 3.4 ~ 115.6mm  
Aperture : F1.65(Wide) F3.7(Tale)  
Lens  
- MOD(Minimum Object Distance) : 1000mm  
High Speed: OFF~1/10K sec  
Low Speed: OFF~X512  
Electronic shutter  
speed  
DIGITAL ZOOM  
White Balance  
2x ~ 16x  
ATW1/ATW2/AWC/MANUAL Mode  
(3200°K, 5600°K, R/B Gain adjustment)  
-10°C~+50°C  
~90%  
Operation Temperature  
Operation Humidity  
Dimensions  
SCC-C4237P/C4239P : 59mm x 59.2mm x 124.2mm  
SCC-C4337P/C4339P : 59mm x 59.2mm x 154.5mm  
(WxHxD)  
SCC-C4237P/C4239P: 421g, SCC-C4337P/C4339P: 564g  
silver  
Weight  
Product Color  
English _35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Waste Electrical & Electronic Equipment)  
Correct Disposal of This Product  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.  
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working  
life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please  
separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse  
of material resources.  
Household users should contact either the retailer where they purchased this product, or their local government  
office, for details of where and how they can take these items for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract. This  
product and its electronic accessories should not be mixed with other commercial wastes for disposal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pyramid Car Audio CD Player CDR22KIT User Guide
Radio Shack Cordless Telephone ET 3504 User Guide
RCA Home Theater System 6 Piece Home Theater Speaker Package User Guide
Ricoh All in One Printer D052 User Guide
RIDGID Drill R82015 User Guide
RIDGID Saw MS1290LZ1 User Guide
Ryobi Trimmer RY13010 User Guide
Samsung Home Theater System HT A100 User Guide
Samsung Stereo System MAX 900 User Guide
Samsung Weather Radio TRC 445 User Guide