SCC-B5342
SCC-B5343
Digital Color Dome Camera
operating instructions
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. Do not drop objects on the product or
apply strong blows to it. Keep away from
a location subject to excessive vibration
or magnetic interference.
1) This device may not cause harmful
interference, and
2. Do not install in a location subject to
high temperature (over 140°F), low
temperature (below -49°F), or high
humidity. Doing so may cause fire or
electric shock.
2) This device must accept any interference
received including interference that may
cause undesired operation.
Caution
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
3. If you want to relocate the already
installed product, be sure to turn off the
power and then move or reinstall it.
4. Remove the power plug from the outlet
when there is a lighting storm. Neglecting
to do so may cause fire or damage to
the product.
5. Keep out of direct sunlight and heat
radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards
extremely bright objects such as sun,
as this may damage the CCD image
sensor.
IC Compliance Notice
This Class A digital apparatus meets
all requirements of the Canadian
Interference.-Causing Equipment
Regulations of ICES-003.
8. Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect
device and shall stay readily operable at
any time.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
12. Use only with cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, or
other apparatus (including amplifiers)
that produce heat.
13. Unplug this apparatus when a card is
used. Use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as powersupply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Overview......................................................................................6
About this guide ............................................................................6
Product overview...........................................................................6
Main features .................................................................................6
Components...................................................................................6
Checking components in the package .......................................6
Components of your camera......................................................7
Installation..................................................................................8
Setting switches ............................................................................8
Setting function switches............................................................8
Connecting cables and changing the settings.........................10
Installing camera .........................................................................11
Before installation..................................................................... 11
Installation procedure............................................................... 11
Adjusting the camera direction..................................................1ꢀ
Appendix A: Specifications for NTSC Standard........... 14
Appendix B: Specifications for PAL Standard .............. 15
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
About this guide
This user guide includes basic instructions for
the product. It is recommended that all users
read this guide before use.
Components
❚
❚
Checking components in the package
Please check your camera and accessories
are included in the package. Those
components are as shown below:
This guide is divided as follows:
Chapter 1, “Overview,” introduces the user guide
and product related information. (This chapter)
Chapter 2, “Installation,” explains how to set and
install the product.
Appendix, “Specifications,” provides the
specifications of the product.
Product overview
❚
Camera
Test Monitor Cable
User’s Guide
This is the high resolution (540 TV lines) dome
camera equipped with a Vari-focal lens, which
has no dynamic delay when implementing
motion pictures, and provides the features
such as digital noise reduction (DNR) by real-
time CCD defect compensation, low speed
shutter (LSS: Auto x128) to implement clear
picture quality, Day/Night color compensation,
and the like.
Tab screw
Note
The test monitor cable is used to test the camera
by connecting to a portable display. If you really
want to connect the camera to a monitoring
display, use the BNC cable.
Main features
Power: DC 12V/AC 24V
Special functions
❚
Line lock (LL) control
Auto white balancing
Horizontal/vertical image reversing
Flickerless control
Low shutter speed control
Backlight compensation control
Automatic switching between color and black
& white modes
Equipped with vari-focal lens
Auto Iris function
Digital noise reduction (DNR)
Dynamic CCD defect compensation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Components of your camera
Your camera has the following components:
Cover dome: Covers the main body for protection.
1
1
Main body: Includes a lens, a switch board, a PCB
2
3
board, screws, and such.
Mount bracket: Used as a ceiling or wall fixture. It
is fixed using three long tab screws provided in the
package.
Cable Stopper: If drawing the cable from a hole in
the ceiling, remove this stopper and pass the cable
through the opening to connect.
4
2
3
4
Zoom lever: Using this lever, the lens zoom can be
adjusted and fixed.
5
6
7
8
Focus lever: The lens focus can be adjusted by
rotating it left or right. Rotate it clockwise for fixing.
Tilt fixing screw: Using this screw, the slope of the
lens can be adjusted and fixed.
Lens
Switch board: Includes two kinds of control switches
such as function switches and phase-control switches.
The board has eight function switches in the middle
and two phase-control buttons on each side of the
function switch area.
Installation Guide Mark: This mark must be aligned
with the marking on the bracket when attaching the
camera to the bracket.
9
0
5
6
7
8
Lock releaser: Push it outward and rotate the main
body in UNLOCK direction when you want to remove
the Mount bracket from the Main body or to remove
the installed camera from the Mount bracket.
9
0
Cable: Connect the Video connector to BNC cable
and Power connector to power adapter.
!
Video connector
Power connector
!
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Setting switches
❚
Setting function switches
To set the available functions on your camera, adjust eight switches as shown below:
No
1
Name
LL
Brief description
Line lock ON/OFF
DEC
8
ꢄ
6
ꢃ
ꢂ
ꢁ
ꢀ
1
2
LSS
Sens-up or Low speed shutter ON/OFF
Horizontal reverse ON/OFF
Vertical reverse ON/OFF
3
H-REV
V-REV
BLC
4
5
Backlight compensation ON/OFF
Flickerless ON/OFF
6
FL
Automatic switching between color and
black & white ON/OFF
7
8
D/N
AWB
Automatic white balance ON/OFF
INC
1. Switch 1 (LL): When this switch is set to OFF, the camera operates in the internal
synchronization mode, while when it is set to ON, the camera operates in the line lock mode.
In the internal synchronization mode, the camera always uses an inside crystal oscillator for
synchronization. However if multiple cameras are connected to a sequential switcher, picture
rolling or flickering may occur when switching from one camera to another. In this case, you
can set this switch to ON to solve this problem.
The line lock mode allows the camera to use the phase of the AC power as the
synchronization reference. In this mode, you can use the phase control buttons(INC/DEC).
Note
When you are using the DC 12V power, set this switch to OFF. The line lock feature will not normally
operate even when the switch is set to ON.
Set the LL switch to ON while the AC power is connected. If any picture roll happens, you have
to adjust the phase using the phase-control buttons. Press the INC or DEC button to increase or
decrease the phase by one degree.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ. Switch ꢀ (LSS): This sens-up mode accumulates the image fields in memory to reduce
noise but increase the brightness and contrast rate. When this switch is set to ON, the
camera automatically switches to a maximum of 128 times of image acquisition speed to
implement a clear picture for darker image.
ꢁ. Switch ꢁ (H-REV): When this switch is set to ON, the camera image is reversed horizontally.
If you want to monitor your site using a mirror, you can use this feature to see the right
image.
ꢂ. Switch ꢂ (V-REV): When this switch is set to ON, the camera image is reversed vertically.
If your camera reluctantly displays the vertically reversed image, you can use this feature to
see the right image.
ꢃ. Switch ꢃ (BLC): When this switch is set to ON, you can view a clear image even though the
camera faces any excessive light such as sunlight and fluorescent light. When it is set to
OFF, the subject with excessive light is not clearly shown.
6. Switch 6 (FL): When this switch is set to ON, the shutter speed is fixed to 1/100 sec (for
NTSC) or 1/120 sec (for PAL) to prevent screen from flickering by the disaccordance
between vertical synchronous frequency (50Hz for NTSC, 60Hz for PAL) and on-and-off
frequency of a light.
ꢄ. Switch ꢄ (D/N): When this switch is set to ON, the camera automatically switches between
color and B&W according to the brightness of the vicinity.
8. Switch 8 (AWB): This switch adjusts white balancing. When this switch is set to ON, this
camera operates in ATW mode, and in case of OFF, this camera operates in AWC mode.
ATW (Auto Tracking White Balance): The color temperature is automatically adjusted according to the
environmental change. (Approx. 2000°K to 11,000°K)
AWC (Auto White Balance Control): It stores the color temperature just when the switch is changed to
OFF. Accordingly color temperatures are adjusted by the stored value.
Caution
-. The IRIS setting range for the camera is approximately 80 to 120 IRE. It means the camera does not
provide the IRIS full open/close feature but the restricted variation range.
-. Use the camera after setting to the proper level (80 IRE or above) because the IRIS hunting may
occur when the level is 75 IRE or below.
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting cables and changing the settings
Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.
❚
To connect cables
1. Connect the BNC cable
to the Video connector
attached on your camera.
ꢀ. Connect the BNC cable
to the Video Input on a
monitor.
Monitor
ꢁ. Connect the power adapter
to the Power connector
attached on your camera.
When the monitor is turned
on, the camera image
appears.
BNC Cable
To adjust the lens focus, zoom, and function settings
1. Remove the Cover dome and Inner cover. For more details about the removing procedures,
see “Installation procedure,” in the Installing camera section on the next page.
ꢀ. Adjust the focus, zoom, and function settings of your camera using the Focus lever, Zoom
lever, and Switch board while you are viewing the image on the screen.
ꢁ. If you want to fix the adjusted focus and zoom, screw up the levers.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing camera
Before installation
❚
Before installing your camera, you have to read the following cautions:
You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it
may cause a breakdown or fire.
When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
Partial blind spot can occur at tilt angles of less than 20°, depending on the lens configuration.
Installation procedure
To install your camera
1
Pry up the outer casing with a flat-head screwdriver
to remove the protective cover from the Main body of
the camera.
1
Remove the Mount bracket from the Main body by
rotating the Main body in the UNLOCK direction while
pushing the Lock releaser outward. If it is not easily
done, rotate the Mount bracket in the LOCK direction
while holding small holes on the Mount bracket.
2
2
3
Fix the Mount bracket to the location (ceiling or wall)
with supplied three screws.
3
Note
The CAMERA FRONT sign on the Mount bracket
should face the camera monitoring area.
Ceiling mount
opener
11
Download from Www.Somanuals.com. All Manuals Search And Download.
If a hole has been drilled on the bracket installation surface for cable access, press down to remove
the Cable Stopper and then draw the cable in. If connecting through the side of the camera, use the
empty space opposite to the side marked CAMERA FRONT.
4
Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning
5
6
the Groove mark on the Main body with the wide groove around the CAMERA FRONT inlay.
Adjust the camera direction. For more details on the direction control, see “Adjusting the camera
direction,” on the same page. When required to adjust the zoom and focus for your camera, see
“Connecting cables and changing the settings,” on page 10.
Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning
two screw holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s
left and right sides.
Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after
aligning the bump inside the Cover dome with the Groove mark on the Main body.
7
8
Adjusting the camera direction
❚
When the camera is fixed on the ceiling, you can adjust
the camera viewing angle. You can rotate your camera
leftward or rightward (Panning), and can change the slope
of your camera upward or downward (Tilting).
Panning
In case of panning, the rotation limit of your camera is
set to 355 degree (100 degree clockwise and 255 degree
counterclockwise). The rotation is stopped by the Stopper
inside of the camera. For panning control, first unfasten
two screws located on the bottom and rotate in the
direction you want, and then fasten them to fix the camera.
Tilting
Tilt can be adjusted between 0° to 90°; however, tilt
angles of less than 20° may result in a partial blind spot,
depending on your lens configuration. To fix the location
after adjusting the tilting angle, use the Tilt fixing screws.
Lens rotation
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When
you install the camera on the inclined ceiling or wall, you can rotate the camera lens to see
a correct direction image.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
SCC-Bꢃꢁꢂꢀ/Bꢃꢁꢂꢁ
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications for NTSC Standard
Item
Product type
Details
CCTV color dome camera
Power input
AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5%
NTSC Standard System (525 Lines, 60 Fields)
Approx. 1.7W
Broadcast type
Power consumption
Image device
1/3 inch IT Type Super-HAD CCD
Total: 811(H) x 508(V), 410,000 pixels
Effective: 768(H) x 494(V), 380,000 pixels
Pixels
Scanning mode
Scanning line frequency
525 Lines, 2:1 Interlace
Horizontal: 15.734Hz(INT)/15.750Hz(LL)
Vertical: 59.94Hz(INT)/60Hz(LL)
Synchronization mode
Horizontal resolution
S/N Ratio
INT/Line Lock (Adjusting the phase using INC/DEC button)
540 TV Lines
Approx. 50dB
SCC-B5343 (Color/BW)
0.4/0.04Lux
0.24/0.024Lux
SCC-B5342 (Color/BW)
0.4/0.4Lux
50IRE
30IRE
15IRE
50IRE
30IRE
15IRE
Sens-up Off
0.24/0.24Lux
Min. object illumination
0.12/0.012Lux
0.12/0.12Lux
F1.2
0.0031/0.00031Lux
0.0019/0.00019Lux
0.0009/0.00009Lux
0.0031/0.0031Lux
0.0019/0.0019Lux
0.0009/0.0009Lux
0 Vp-p, 75ohm, Harness cable)
Sens-up x128
Signal output
Lens
PAN function
TILT function
COMPOSITE Video(1
.
0 Vp-p, 75ohm, BNC), Test Monitor OUT(1
.
Auto Iris (DC) / Focal length: 2.5 to 6.0mm / Aperture ratio: 1.2
Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
Range: 0 to 90°
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Controls
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Product color
SCC-B5342N/B5343N : White
Operation temperature
Operation humidity
Size
-10°C to +50°C
Up to 90%
128(Ø) x 91(H)mm
327g
Weight
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Specifications for PAL Standard
Item
Product type
Details
CCTV color dome camera
Power input
AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5%
PAL Standard System (625 Lines, 50 Fields)
Approx. 1.7W
Broadcast type
Power consumption
Image device
1/3 inch IT Type Super-HAD CCD
Total: 795(H) x 596(V), 470,000 pixels
Effective: 752(H) x 582(V), 440,000 pixels
Pixels
Scanning mode
Scanning line frequency
625 Lines, 2:1 Interlace
Horizontal: 15.625Hz(INT)/15.625Hz(LL)
Vertical: 50Hz(INT)/50Hz(LL)
Synchronization mode
Horizontal resolution
S/N Ratio
INT/Line Lock (Adjusting the phase using INC/DEC button)
540 TV Lines
Approx. 50dB
SCC-B5343 (Color/BW)
0.4/0.04Lux
0.24/0.024Lux
SCC-B5342 (Color/BW)
0.4/0.4Lux
50IRE
30IRE
15IRE
50IRE
30IRE
15IRE
Sens-up Off
0.24/0.24Lux
Min. object illumination
0.12/0.012Lux
0.12/0.12Lux
F1.2
0.0031/0.00031Lux
0.0019/0.00019Lux
0.0009/0.00009Lux
0.0031/0.0031Lux
0.0019/0.0019Lux
0.0009/0.0009Lux
0 Vp-p, 75ohm, Harness cable)
Sens-up x128
Signal output
Lens
PAN function
TILT function
COMPOSITE Video(1
.
0 Vp-p, 75ohm, BNC), Test Monitor OUT(1
.
Auto Iris (DC) / Focal length: 2.5 to 6.0mm / Aperture ratio: 1.2
Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
Range: 0 to 90°
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Controls
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Product color
Operation temperature
Operation humidity
Size
SCC-B5342P/B5343P : White
-10°C to +50°C
Up to 90%
128(Ø) x 91(H)mm
327g
Weight
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
❚
Download from Www.Somanuals.com. All Manuals Search And Download.
|