User Guide
User Guide
1. Read all of these instructions.
CAUTION
2. Save these instruction for later use.
RISK OF ELECTRIC
SHOCK, DO NOT OPEN
3. Unplug this appliance system from the wall
outlet before cleaning
Do not use liquid cleaners or aerosol cleaner.
Use a damp cloth for cleaning.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
4. Do not use attachments not recommended by
the appliance manufacturer, as they may cause
hazards.
The lightning flash, with an arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure, that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
5. Do not use this appliance near water for
example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a
swimming pool, etc.
6. Do not place this appliance on an unstable cart,
stand, or table.
The appliance may fall causing serious injury to
a child or adult, and serious damage to the
appliance.
Use only with a cart or stand recommended by
the manufacturer’s instructions, and use a
mounting kit approved by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instruction in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
cause the appliance and cart
combination to overturn.
IMPORTANT SAFEGUARDS
i
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
Contents
1. Introduction
............................................
1. Introduction
2
3
Samsung CCTV B/W Camera (SBC-330A(P)
/331A(P)/300AP/301AP) is a surveillance camera
that employs the latest CCD technology and can be
connected to a CCTV system to provide the best
surveillance capabilities.
..................................................
2. Features
..............................................
3. Installation
4
4
...................
................
Precautions in Installation and Use
Connecting Auto Iris Lens Connector
5
..................................................
Mounting Lens
6
Broadcast System
SBC-330A/331A
...........................
Setting Lens Selection Switch
7
: EIA
.......................................
Adjusting Back Focus
8
SBC-330AP/331AP/300AP/301AP : CCIR
...........................................
Connecting Cable
10
Number of CCD pixels
...........
4. Names and Functions of Parts
13
SBC-330A
SBC-331A
: 1/3" 27 megapixel (Normal)
: 1/3" 41 megapixel (Hi-Band)
........................
Names and Functions of Parts
Function Switches
13
.............................................
16
SBC-330AP/300AP : 1/3" 32 megapixel (Normal)
SBC-331AP/301AP : 1/3" 47 megapixel (Hi-Band)
..........................
5. Product Specification
19
Power Supply System
SBC-330A(P)/331A(P) : AC 24V , DC12V
SBC-300AP/301AP
: AC 220V~240V
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
2. Features
3. Installation
Precautions in Installation and Use
High Sensitivity
Adopting the 1/3" Super HAD CCD that has the
latest built-in microchip lens, the high sensitivity is
realized.
➀
Do not attempt to disassemble the camera
yourself.
➀
Be cautious in handling the camera. Avoid
striking or shaking the camera. Be cautious to
avoid damage on the camera caused by improper
storage or operation.
Excellent Back Light Compensation
The built-in backlight compensation (BLC) function
provides a clear, sharp image even when monitoring
strongly backlit subjects.
➀
➀
Do not expose this camera to rain or moisture.
Do not operate this camera on a wet place.
Digital Line-lock
Do not use strong or abrasive detergents when
cleaning the camera body.
The control and reliability has been enhanced due to
the Full Digital Line Lock, which allows users to
adjust the Line Sync Phase.
Use a dry cloth to clean the camera.
➀
Keep the camera at a cool place away from the
direct sunlight. Leaving it under the direct
sunlight may result in the malfunction of the unit.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
Connecting Auto Iris Lens Connector
Mounting the Lens
Prepare the following Auto Iris Lens Connector
supplied with the camera.
Loosen a screw fixing the Flange Back Adjustment
Ring by turning it counterclockwise and turn the
Adjustment Ring to the "C" direction
(counterclockwise) until it stops. Failure to do so
may result in a damage caused by the bump of the
lens against the image sensor part in the camera
when mounting the lens.
Rib
Pin3
Pin1
Pin4
Pin2
C Direction
Connect the cable of the control cable, whose
covering is stripped, to the Auto Iris Lens Connector
as shown below.
V
ID
E
Pin Number DC Control Type Video Control Type
O
D
C
LEN
1
2
3
4
Damp(-)
Damp(+)
Drive(+)
Drive(-)
Power Source (+9V)
Not used
S
Video Signal
GND
Auto Iris
Control Cable
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
Setting Lens Selection Switch
Adjusting Back Focus
Although the Back Focus of the camera has been
adjusted in the factory before its shipment, the focus
may not be accurate for a certain type of the lens.
In this case, follow the procedures below to adjust
the Back Focus. First, following is how to adjust the
Back Focus of the Fixed Focus Lens.
When lens mounting is completed, set the Lens
selection Switch on the rear of the camera
according to the mounted lens type.
When the mounted lens is an Auto Iris Lens of the
DC control type, set the Lens Selection Switch to
"DC". When the mounted lens is an Auto Iris Lens of
the Video control type, set the Lens Selection
Switch to "VIDEO".
➀
➀
Lightly loosen the screw fixing the Back Focus
Adjustment Ring using a screwdriver.
Image a vivid subject (with check patterns) at a
distance of more than 10m away and turn the
Focus Ring to the infinity (∞) position.
➀
➀
Adjust the Back Focus Adjustment Ring to obtain
the clearest image of the subject.
Fasten the screw fixing the Back Focus
Adjustment Ring.
VIDEO
S
LEN
DC
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
The following describes how to adjust the Back
Focus when using a Zoom lens.
Connecting Cable
After mounting the lens and setting the Lens
Selection Switch, connect the prepared cable to
each terminal of the camera.
➀
Lightly loosen the screw fixing the Back Focus
Adjustment Ring using a screwdriver.
➀
Image a vivid subject (with check patterns) at a
distance of 3~5m away and adjust the zoom of
the lens to TELE as far as it goes. Then adjust
the Focus Ring of the lens to obtain the clearest
image of the subject.
➀
First, connect one end of the BNC cable to the
Video Output Terminal (VIDEO OUT) of the
camera.
➀
Adjust the zoom of the lens to WIDE as far as it
goes. Then turn the Back Focus Ring of the
camera to obtain the clearest image of the
subject.
➀
Then connect the other end of the BNC cable to
the Video Input Terminal of the monitor.
➀
➀
Repeat no.
➀
&
➀
2~3 times to exactly coincide
the zoom focus from TELE and with that from
WIDE.
Fasten the screw fixing the Back Focus
Adjustment Ring.
VIDEO LINE
Video B
AUDIO LINE
Video A
IN OUT
Video C
A
B
C
IN
IN OUT
IN OUT
OUT
Video In Terminal on the rear of the monitor
O
E
ID
V
LENS
C
D
O
E
ID
V
N
E
L
C
D
BNC Cable
Note:
Video Out Terminal
(VIDEO OUT)
Turning the Back Focus Adjustment Ring to the "C" direction
beyond the adjustable range makes a sound at the limit.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
➀➀ AC24V/DC12V Power Input Camera.
AC230V Power Input Camera
Connect 2 lines of the power adapter using a
Phillips screwdriver to the Power IN Terminal of
the camera as shown below.
Connect the power input cord to the AC 230V
power source.
※ Without the distinction of the polarity, connect to
the AC 24V or AC 12V power source.
VIDEO
LE
DC
VIDEO
E
L
DC
AC24V
DC12V
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
Auto Iris Lens Connector
4. Names and Functions of Parts
Used for supplying power, which is required to
control the iris of the lens, as well as control signal,
video signal, or DC signal to the Auto Iris Control
Lens.
Names and Functions of Parts
• Side View
Auto Iris Lens Control Cable
Used for transmitting the control signals to the
Groove for Mount Adapter
Auto lris Lens Connector
camera to control the iris of the lens.
Flange-Back
Adjustment Ring
Flange-Back Adjustment Ring
Used for adjusting the Back Focus.
Auto Iris Lens
V
ID
E
O
D
C
ALC Lens Selection Switch
Used when selecting the type of Auto Iris Lens to
use.
S
ALC Lens
Selection Switch
DC : Select this switch to DC when Iris Lens
requiring DC control signal is mounted.
Auto Iris Lens Control
Cable
VIDEO : Select this switch to VIDEO when Auto Iris
Lens requiring VIDEO control signal is
mounted.
Groove for Mount Adapter
Use this groove for fixing the mount adapter to be
connected to the bracket with screws to mount the
camera on the bracket.
Auto Iris Lens (Option)
Lens to be mounted on the camera
Note
When the surface of the camera lens is
contaminated, wipe the surface gently with a tissue
for lens or a cotton cloth applied with ethanol.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
➀
➀
➀
Power Connection Terminal
Terminal to be connected to the power (adapter)
• Rear Panel
cable- Connect it to AC 24V or DC 12V.
AC24V/DC12V Power Input Camera
Power Indication LED
While the power is properly supplied to the
camera, the LED is turn on.
V-Phase Control
In the Line Lock mode (SYNC LL), use a tool
such as a screwdriver to adjust the vertical sync
phase.
5
6
PWR
AC 24V
DC 12V
VIDEO OUT
➀
Function Switches
1
1. L/L
3. ELC
2. BLC
4. AGC
AC230V Power Input Camera
ON
SW1 SW2 SW3 SW4
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
1) SW1(L/L):
3) SW2 (ELC):
If this switch is set to OFF, the camera will
operate in the internal synchronization mode, and
if the switch is set to ON, the camera will operate
in the line lock mode.
Use this switch with the Manual Iris Lens. While
this switch is ON, the speed of the electronic
shutter varies with the brightness of the subject
from 1/60 to 1/100,000 sec for automatically
controlling the brightness of the screen.
However, with the Auto Iris Lens (DC or Video
Control), be sure to switch OFF.
If you are monitoring in the automatic switching
mode with multiple cameras connected to a
sequential switcher, and the cameras are set to
INT (internal synchronization) mode, then picture
rolling or flickering will occur during switching
from one camera to another.
4) SW4(AGC):
Such picture rolling on the monitor can be
remedied by setting this switch to ON and then
adjusting the vertical sync phase with the
V-Phase Control.
This switch turns on or off the automatic gain
control (AGC) function, which is a function that
automatically increases the camera's sensitivity
when ambient light drops below a preset level.
Set this switch to ON to automatically adjust the
"gain".
※
When using DC 12V power, set the L/L switch to
OFF.
If the L/L switch is set to ON, the camera will not
operate normally.
➀ DC Iris Level Control
When the ALC Lens Selection Switch is set to
DC, adjust this Iris Level Control using an
adjustment rod such as a screwdriver.
2) SW2(BLC):
This switch turns on or off the back light
compensation (BLC) function. When there is a
spotlight or strong light from behind the subject,
the subject may appear dark on the monitor. In
such backlighting conditions, set this switch to
ON for clear viewing.
➀ Video Output Terminal
This is a terminal to be connected to the Input
Terminal of the monitor. Through this terminal,
the video signals are output.
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
5. Product Specifications
SBC-330A/331A
ALC /ELC
ALC
DC IRIS LENS
VIDEO LENS
ELC
Item
Product Type
Broadcasting
System
Contents
CCTV B/W Camera
EIA STANDARD SYSTEM
Electronic SHUTTER IRIS function
COMPOSITE VIDEO OUT
1V p_p 75 Ω/BNC
Video Output
Power Source
CCD
1/3” IT type S-HAD CCD
330A : 510(H) x 492(V)
331A : 768(H) x 494(V)
525 Line, 2:1 Interlace
INTERNAL : 15,750 HZ(H)
60 HZ(V)
No. of Pixel
AC24V±10%(60Hz±0.1Hz)
DC12V+10%-5%
Scanning Type
Frequency
Power Consumption
Operating
Temperature
Operating
Humidity
About 2 Watts
-10℃~+50℃
LINE LOCK :15,750 HZ(H)
60 HZ(V)
~90%
Syne Type
Resolution
INTERNAL
Size
65(W) x 52(H) x 133(L)mm
(BNC included)
LINE LOCK(When AC24V power source is used)
330A : 380TV Lines
331A: 550TV Lines
more than 50dB
Weight
Altitude
About 420g
Below 3000m
S/N Ratio
Min. Object
Illumination
0.1 Lux F1.2 (50 IRE)
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
User Guide
ALC /ELC
ALC
DC IRIS LENS
VIDEO LENS
ELC
SBC-330AP/331AP/300AP/301AP
Item
Product Type
Broadcasting
System
Contents
Electronic SHUTTER IRIS function
COMPOSITE VIDEO OUT
1V p_p 75 Ω/BNC
CCTV B/W Camera
Video Output
Power Source
CCIR STANDARD SYSTEM
300AP/301AP
CCD
1/3” IT type S-HAD CCD
AC220V~240V±10%(50Hz±0.1Hz)
330AP/331AP
No. of Pixel
330AP/300AP : 500(H) x 582(V)
331AP/301AP : 752(H) x 582(V)
625 Line, 2:1 Interlace
INTERNAL : 15,625 HZ(H)
50 HZ(V)
AC24V±10%(50Hz±0.1Hz)
DC12V+10%-5%
Scanning Type
Frequency
Power Consumption
300AP/301AP: About 3 Watts
330AP/331AP: About 2 Watts
LINE LOCK :15,625 HZ(H)
50 HZ(V)
Operating
Temperature
Operating
Humidity
Size
-10℃~+50℃
Syne Type
Resolution
INTERNAL
LINE LOCK(When AC power source is used)
330AP/300AP : 380TV Lines
331AP/301AP: 550TV Lines
more than 50dB
~90%
65(W) x 52(H) x 133(L)mm
(BNC included)
S/N Ratio
Weight
Altitude
300AP/301AP : About 520g
330AP/331AP : About 420g
Below 3000m
Min. Object
Illumination
0.1 Lux F1.2 (50 IRE)
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital B/W Camera
-
SBC 330A /330AP
-
SBC 331A /331AP
-
SBC 300AP /301AP
User Guide
Part No.: AB68-00346A (Rev. 01)
Printed in Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
|