SRP - 770
Thermal Label Printer
Operator’s Manual
JE68-00131B
Rev. 1.02
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Unpacking & Repacking
Table of Contents
Your printer box should include these items. If any items are damaged or missing,
please contact your dealer for assistance.
Note : Please keep the packing materials(①,②,④,⑥) for future repacking to send
a printer for repairs.
⑨ Label
1. Unpacking & Repacking.........................................................................5
2. Samsung Label Printer ...................................................................6
3. Connecting the Power Supply......................................................7
4. Connecting the Interface Cable ..................................................8
5. Installing or Replacing the Paper Roll......................................9
6. Setting the Dip Switches .............................................................10
7. The Self Test.....................................................................................11
8. The Peel-off ......................................................................................12
9. Using Fan Fold Paper.....................................................................13
⑧ Operator’s Manual & CD
(Paper)
⑥ Cushion
(TOP)
⑦ Power Cord
③ Power Supply
⑤ Printer (SRP-770)
② Cushion
(Bottom)
10. Driver Install Guide.....................................................................14
I. To install SRP-770 windows driver
II. To use USB interface
III. Tip & Trouble shooting
④ Pe-bag
① Printer Box
※ You can repack the printer package in above numeric order(①~⑨)
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Samsung Label Printer
3. Connecting the Power Supply
CAUTIONS:
When connecting or disconnecting the power supply from the printer, make sure that
the power supply is not plugged into an electrical outlet. And the power supply’s
rated voltage and your outlet’s voltage do not match, contact your dealer for
assistance. Then do not plug in the power cord. Otherwise, you may damage the
power supply or the printer.
Status Indicator
Power Switch
Feed Button
Cover Peel-off
1. Make sure that the printer’s power switch is turned off, and the power supply’s
power cord is unplugged from the electrical outlet.
Cover Open/Close
2. Check the label on the power supply to make sure that the voltage required by the
power supply matches that of your electrical outlet.
Printer Head
3. Plug in the power supply’s cable as shown below. Notice that the flat side of the
plug faces down.
Paper Holder
Paper Guide
Paper(gap) Sensor
Peel-off Sensor
Paper Adjuster
Power Connector
Dip Switch
Interface Connectors
(RS-232C, IEEE1284, USB)
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connecting the Interface Cable
5. Installing or Replacing the Paper Roll
① Open Cover
② Open Guides
③ Install Roll
Universal Serial Bus
(USB)
Parallel Interface
Serial Interface
RS-232 default
setting is 19200 baud,
no parity, 8 data bits
and 1 stop bit
④ Close Guides to the Width of the paper
⑤ Close Cover
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Setting The Dip Switches
7. The Self Test
6-1. Setting the Dip Switches
The self-test checks whether the printer has any problems. (You cannot perform this
procedure if using the printer’s label peel-off option) If the printer does not function
properly, contact your dealer. The self-test checks the following;
The Dip Switches are located on the bottom of the printer. The Dip Switches are used to
set the Printer to perform various functions. Follow these steps when changing Dip
Switches setting :
1.
2.
3.
Make sure that paper roll has been installed properly.
1. Turn the printer power switch off.
Turn on the power while holding(2sec) down the FEED button. The self-test begins.
The self-test prints the current printer status, which provides the control ROM version
and the DIP switch setting.
2. Remove the screw on the bottom of the printer and open the bracket.
3. Flip the Dip Switches using tweezers or another narrow-ended tool. Switches are
off when up and on when down in the Figure below.
4. The new setting takes effect when you turn on the printer.
※ Cleaning Head
Note : Always change Dip Switch settings only when the printer is turned off.
Paper dust on the heating elements may lower the printer quality. In this case, clean the
print head as follows :
6-2. Functions of Dip Switches
Cautions 1. Turn Off the printer power before cleaning.
2. Note that the thermal head becomes very hot during normal operation,
creating the danger of burn injury. Be sure to wait for about 10 minutes
after turning printer power off before beginning the cleaning.
6-2-1. Dip S/W 1
6-2-2. Dip S/W 2
Details
NO
Functions
No
Functions
Details
Baud Rate
2
1
Speed
2.5 ips
3.0 ips
4.0 ips
5.0 ips
Density
0(Low)
7
2
1
Off
On
Off
On
1. Open the printer cover.
Off
Off
On
On
4
Off
Off
On
On
Off
On
Off
On
3
Off
On
Off
On
Off
Off
On
On
9,600 bps
19,200 bps
57,600 bps
115,200 bps
Speed
Selection
Baud
Rate
2. Clean the thermal element (the area which is marked a thin black line) of the
thermal head with a cotton swab moistened with a alcohol solvent (ethanol,
methanol, or IPA).
3. After confirming that the alcohol solvent has been dried up completely,
close the cover-open.
1,2
1,2
3
4
Reserved
Reserved
Density
Selection
3,4
Developer
Mode
Note
1. Never touch the thermal element with your hand,
then the thermal element can be damaged.
2. Don’t scratch the printer head.
5~8
Default --- off
13
20(High)
5,6,
7
Developer
Mode
Default --- off
Position
Selection
Off
On
Move to Cutting Position
Move to top of next page
8
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
8. The Peel-off
9. Using Fan Fold Paper
Printers can Peel-off a single label.
You must remove the label before the printer prints the next label.
Insert paper through both the rear slot and guides.
Adjust holders and guides to the width of the paper.
① Open the peel-off cover and turn on peeler switch.
Open the Dust Cover
and Insert paper
Dust Cover
Adjust holders papers and paper Fixed
Adjust Guides
② Remove the one a paper and
③ Adjust the paper guides and close the cover.
insert the paper through slot.
remove
Paper Fixed
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. If it is first time to install SRP770 windows driver, you can see the Welcome message as
below. Please click on Next> to continue install procedure.
10. Driver Install Guide
I. To install SRP770 windows driver
1. Insert CD-ROM included in your printer package then install guide program will appear
automatically. Please click on Windows Drivers.
** If previous version driver is already installed in your system, some other type
window will appear. In this case, please refer to “Ⅲ. Tip & Trouble shooting”
2. You can see the driver auto-install program prepares to install driver matching your
windows system.
4. If you accept the license agreement, click on Yes to continue install procedure.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If you want to use USB interface with SRP770 printer, please select both “SAMSUNG
7. Click on Finish to exit auto-installer program.
SRP770” and “SAMSUNG USB Port Monitor” together and click on Next>.
8. You can see the SAMSUNG SRP770 driver is correctly installed in Printer folder.
6. Just wait until auto-installer program finishes drivers setup.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
5th - 1. In Windows XP or 2000,
II. To use USB interface
1) When you turn on the printer power switch first time after installing USB port driver, the
OS recognize the printer and pop up the window to complete USB driver installation a.
Please click on Next>.
Microsoft windows basically supports Serial and Parallel interface without installing any port
drivers but in case of USB interface, USB port driver should be pre-installed. Please follow
next steps to properly install Samsung USB port driver in your system.
1st. Turn off the printer power switch and don’t turn on while auto-install program setup
drivers in your system.
2nd . Execute auto-install program as shown in “Ⅰ.To install SRP770 windows driver”
or manually.
3rd. During installation procedure, please select both SAMSUNG SRP770 and SAMSUNG USB
Port Monitor together as below.
2) Just wait…
4th. After driver installation is finished, Please connect USB cable between your system and
printer correctly and turn on the printer power switch.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3) If the following message box appears while your installation, just click on
5) In Ports Tab of SRP770 Properties window, select SSUSB0: and click on Apply.
Continue Anyway to continue install procedure.
4) Click on Finish to complete installation.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5th -2. In Windows 98 or Me,
III. Tip & Trouble shooting
1) When you turn the printer power switch first time after installing USB port driver, the OS
recognize the printer and pop up the window to complete USB driver installation. Just wait.
1. When the previous version driver of SRP770 is already installed your system,
please remove that driver before installing new driver as follows.
1) If auto-installer search old version drivers in your system, the below windows will
appear. Select Remove and click on Next> to clean up your system before installing new
driver.
2) In Details Tab of SRP770 Properties window, select SSUSB0: and click on Apply.
2) Click on OK and Restart in next message box.
3) After rebooting your system, re-execute auto-install program and follow steps shown in
“I. To install SRP770 windows driver” to install new driver.
6. Please print Test page in General Tab to confirm the USB port driver is correctly installed
in your system.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. If you meet the following message box while driver installation.
5. When your system does not recognize USB connection after installing USB
port monitor.
Ans.) After deleting ‘USB print support’ (or other name marked by an exclamation
mark) under Universal Serial Bus Controller in Device Manager, please re-install USB
port monitor. During installing USB port monitor, I recommend to turn off printer power.
You can open Device Manager window with following procedure.
1) Windows 9x/Me/2000
- Right-click on My Computer on Desktop and select Properties.
- Hardware - Device Manager - Universal Serial Bus Controller - USB print support
2) Windows XP
Ans.) If you have used the old version auto-installer, that message box is likely to
appear. Just click on Yes to replace old file with new file.
- Start - My Computer - View System Information
- Hardware - Device Manager - Universal Serial Bus Controller - USB print support
3. How to execute driver auto-install program if the install guide program will
not automatically appear when you insert the CD-ROM.
Ans.) Double click 770Installerxxxxx.exe(‘xxxxx’ means driver version number) in
“CD-ROM drive-drivers” folder by using windows explorer.
4. How to select paper size in Windows XP or 2000.
Ans.) If you use Windows XP of 2000, there are two places to set the paper size in the
printer properties window in comparison that there are just one place in Windows 98 or
Me.
1) First Place : General Tab – Print Preferences… - Advanced – Advanced Option window
2) Second Place : Device Setting Tab.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
【 Specification 】
Printing method
Dot density
Printing width
Paper width
Printing speed
Receive Buffer Size
Thermal line printing
203 dpi (8 dot/mm)
25.4 ~ 101.6 mm
38.1 ~ 104 mm
127 mm/sec
4K Byte
※ Note : Printing speed may be slower, depending on the data transmission speed
and the combination of control commands.
Input voltage
Frequency
100~240V AC
50/60 Hz
Supply voltage
Output voltage
DC 24V
5 ~ 45 ℃ (Operating)
-25 ~ 70 ℃ (Storage)
30 ~ 80 % RH (Operating)
10 ~ 90 % RH (Storage)
; Except for paper
10,000,000 lines
Temperature
Environmental
conditions
Humidity
LIFE
Mechanism Head
Mechanism
5×107 pulse (50km)
20,000,000 lines
MCBF
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|