SADT - 104WM
Wall Mount Adaptor
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
1
2008-01-24 오전 10:24:02
3. If you install the Wall Mount Adaptor in a wall, place the template on the wall and drill 4
holes for the anchor bolts (M10) and nuts (M10) before inserting them.
If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM). If
installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM).
TEMPLATE
The positions for
installing a ANCHOR BOLT
80 mm
4. Prepare the Camera Adaptor for the applicable camera.
Remove the Bracket Sealing from the Camera Adaptor.
BRACKET CEILING
CAMERA ADAPTOR
2_SADT-104WM
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
2
2008-01-24 오전 10:24:03
5. Remove the Connectors at the end of the Camera Adaptor.
In the next step, peel off the coating of the cable and connect it to the external cable
using soldering. (See the wiring diagram of the installation guide for the Camera to
connect the cables.)
Lastly, use an insulation tape to wrap up the soldering portion of two cables.
Repeat the above steps to connect all of the 4 Connectors to the appropriate external
cables.
CAMERA ADAPTOR
CAMERA ADAPTOR
CABLE
CONNECTOR
EXTERNAL CABLE
EXTERNAL CABLE
BNC JACK
SOLDERING
CONNECTOR
BNC JACK
CONNECTOR
SADT-104WM_3
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
3
2008-01-24 오전 10:24:04
6. Prepare the Camera Adaptor for the applicable camera. Refer to the installation guide for
the applicable camera and configure the initial settings of the Camera Adaptor.
(For more information, see the installation guide for the Camera)
Insert the cable of the Camera Adaptor into the Wall Mount Adaptor before pulling it out
throught the hole of the Cover Fixing Part.
the place for joining a cover
WALL MOUNT ADAPTOR
CAMERA ADAPTOR
7. Insert the 4 screws on the Wall Mount Adaptor into the corresponding screw holes on the
Camera Adaptor and fix them so that the Camera Adaptor is secured to the Wall Mount
Adaptor.
Ensure that the part “A” of the Camera Adaptor faces the arrow direction in the figure
during the fixation.
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
SCREW
"A"
The place for
joining a screw
"A"
CAMERA ADAPTOR
SCREW
CAMERA ADAPTOR
4_SADT-104WM
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
4
2008-01-24 오전 10:24:05
8. Pull out cables such as external power cable, BNC cable and communications cable
through the rear of the Wall Mount Adaptor, which are necessary for connecting the
camera.
It is recommended to keep the cables about 100mm longer than the cover fixing part.
the place for joining a cover
WALL MOUNT ADAPTOR
9. Use the anchor bolts and nuts to secure the Wall Mount Adaptor to the wall.
WALL MOUNT ADAPTOR
ANCHOR BOLT
CAMERA ADAPTOR
SADT-104WM_5
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
5
2008-01-24 오전 10:24:07
ꢀ0. Connect the cables of the Camera Adaptor with the outward cables, which then you
push in through the Cover Fixing Part to the Wall Mount Adaptor.
Insert one piece of the two-strand cable into an empty area of the Wall Mount
Adaptor as in the figure below and push the other one into the Wall Mount Adaptor.
When you insert the cables into the Cover Fixing Part so that the insulation of the
cable junction is not peeled off or torn.
CAUTION
the place for joining a cover
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
< Insert one piece of the two-stranded cable >
< Insert the other piece of the two-stranded cable >
ꢀꢀ. As in the bottom-left figure, insert the rib of the cover into the Cover Fixing Part. Then,
push the Sanp-Fit of the cover into the Cover Fixing Part so that the cover is fastened
with the Wall Mount Adaptor.
WALL MOUNT ADAPTOR
the place for joining a cover
WALL MOUNT ADAPTOR
COVER
COVER
CAMERA ADAPTOR
CAMERA ADAPTOR
RIB
SNAP-FIT
COVER
6_SADT-104WM
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
6
2008-01-24 오전 10:24:08
ꢀ2. Prepare the Camera Body.
Put up the Safety Wire, attached to the camera, on the Safety Hook.
To avoid accidental fall and consequent damage to the camera during installation or
detachment, make sure the Safety Wire is secured to the hook.
CAUTION
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
CAMERA ADAPTOR
CAMERA ADAPTOR
SAFETY HANGER
SAFETY HANGER
SAFETY WIRE
SAFETY WIRE
CAMERA
CAMERA
SADT-104WM_7
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
7
2008-01-24 오전 10:24:10
ꢀ3. Align the Guide 1 of the Camera with the Guide 2 of the Camera Adaptor and insert the
3 Guides of the Camera into the corresponding Guide Holes of the Camera Adaptor.
Then, turn the camera clockwise by 10 degrees.
Make sure that the part "A" is moved from position 1 to 2.
WALL MOUNT ADAPTOR
CAMERA ADAPTOR
CAMERA ADAPTOR
GUIDE 2
GUIDE 3
GUIDE HOLE
GUIDE
Align!
GUIDE 1
SCREW
CAMERA
CAMERA
CAMERA ADAPTOR
GUIDE HOLE
GUIDE
CAMERA
WALL MOUNT ADAPTOR
"A"
CAMERA
1
2
8_SADT-104WM
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
8
2008-01-24 오전 10:24:11
ꢀ4. Use the screws, attached to the Camera, to firmly fix the Camera body with the
Camera Adaptor.
(Once you removed the camera from the Camera Adaptor, loosen the screw, turn the
camera counterclockwise by about 10 degrees, and then pull it down.)
If you do not fix the screws, CAMERA BODY could be separated from the CAMERA
ADAPTER due to the shake.
CAUTION
To avoid safety accident and camera damage, make sure to fix the screws.
WALL MOUNT ADAPTOR
CAMERA
SCREW
SADT-104WM_9
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd
9
2008-01-24 오전 10:24:12
Product Specification
Location for use: Indoors
Installation Spot: Wall or Vertical Structure
Dimension: See the figure
Weight: 241g
Material: plastic
Operation Temperature: -10˚C ~ 50˚C
ꢅꢆꢅ
ꢂꢂꢆ
ꢀꢁ
Accessories
..................................
Template
1
1
1
.......................................
Cover
..................................
MANUAL
ꢀ0_SADT-104WM
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd 10
2008-01-24 오전 10:24:12
(Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
SADT-104WM_ENG.indd 11
2008-01-24 오전 10:40:05
|