Samsung Home Security System SCV 2080R User Guide

High Resolution D/N IR Vandal Dome Camera SCV-2080R User Guide  
Before installing and operating this product,  
please read this manual thoroughly.  
ENGLISH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Thank you for purchasing a SAMSUNG CCD CAMERA.  
Before operating the camera, confirm the camera model and correct input  
power voltage. In order to that you can understand this manual thoroughly,  
we will introduce our model description.  
n SIR-4260 SERIES  
• NTSC MODEL  
SCV-2080RN  
• PAL MODEL  
SCV-2080RP  
The lightning flash with an arrowhead symbol, within an equilateral triangle is  
intended to alert the user to the presence of uninsulated “dangerous voltage”  
within the product's enclosure that may be of sufficient magnitude to constitute  
a risk of electric shock to persons.  
n MODEL DESCRIPTION  
• SCV-2080RX  
_
The exclamation point within an equilateral triangle is intended to alert the user  
to the presence of important operating and maintenance (servicing) instructions  
in the literature accompanying the appliance.  
SIGNAL SYSTEM  
• SIGNAL SYSTEM  
N NTSC MODEL  
P PAL MODEL  
INFORMATION-This equipment has been tested and found to comply with  
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instruction manual, may  
cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference  
at his own expense.  
WARNING - Changes or modifications not expressly approved by the  
manufacturer could void the user's authority to operate the equipment.  
WARNING : To prevent electric shock and risk of fire hazards:  
Do NOT use power sources other than that specified.  
Do NOT expose this appliance to rain or moisture.  
This installation should be made by a qualified service person and  
should conform to all local codes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Features  
Features ……………………………………………………………… 5  
Warnings & Cautions………………………………………………… 6  
Precautions…………………………………………………………… 7  
Components and Accessories ……………………………………… 8  
Overview …………………………………………………………… 9  
Ultra High Sensitivity  
DAY&NIGHT(ICR)  
This camera has a function that automatically  
selects the mode that is appropriate for daytime  
or night-time conditions.  
The COLOR mode operates in daytime conditions  
to provide optimum colors, and BW mode  
operates in night-time conditions to enhance the  
definition of the image.  
The built-in high sensitivity CCD produces a  
clear image even in 0Lux(B/W, IR-LED ON)or  
lower illumination.  
High Resolution  
Installation…………………………………………………………10  
n Installation………………………………………………………………… …10…  
By adopting a diagonal 6mm(1/3") 410,000 (NTSC)  
pixel, 470,000(PAL) pixel SONY CCD, the camera  
produces clear picture quality with a horizontal  
resolution of 600 TV lines for color and a horizontal  
resolution of 700 TV lines for BW mode.  
IR MODE Function  
…10…  
n Adjust the panning, tilting and rotate mechanism while checking the position on the monitor  
n
Adjusting varifocal lens zoom and focus………………………………… …12  
This function prevents the saturation of the  
image by the IR illuminators at short distances.  
• Connection …………………………………………………………… 12  
n Connecting To Monitor…………………………………………………… …12…  
Communication  
SSNR 3  
n Connecting To Power……………………………………………………… …13…  
n RS-485 communication control…………………………………………… …14…  
n Using Coaxial Communications…………………………………………… …15  
(Samsung Super Noise Reduction)  
RS-485, Coaxial communication methods are  
supported.  
- RS-485 Communications  
The high-performance W-V DSP chip  
effectively removes low-light gain noise and  
ghosting to provide clear images even in dark  
environments.  
:
SAMSUNG-T, Pelco-P, Pelco-D, Vicon,  
Panasonic, Bosch, Honeywell, SAMSUNG-E  
Operating Your Camera …………………………………………16  
n Menu Configuration……………………………………………………… …16…  
n Menu Setup………………………………………………………………… …17…  
- Coaxial Communications  
: Pelco Coaxitron  
· LENS……………………………………………………………………… …18…  
· EXPOSURE……………………………………………………………………18…  
· WHITE BALANCE………………………………………………………… …20…  
· SSDR…………………………………………………………………………21…  
· BACKLIGHT…………………………………………………………………21…  
· SSNR3…………………………………………………………………… 23…  
· DAY/NIGHT………………………………………………………………… 24…  
· SPECIAL…………………………………………………………………… …26…  
· EXIT…………………………………………………………………………31  
DIS (Digital Image Stabilizer)  
OSD  
The DIS function compensates for any camera  
movement, to produce more stable pictures.  
The camera’s OSD is complimented by 18 languages.  
- NTSC : Korean, English, French, Spanish, Japanese,  
Portuguese, Taiwanese  
- PAL : English, French, German, Spanish, Italian,  
Chinese, Russian, Czech, Polish, Romanian,  
Serbian, Swedish, Danish, Turkish, Portuguese  
SSDR  
(Samsung Super Dynamic Range)  
For images with high contrast between bright  
and dark areas from difficult lighting  
conditions such as backlighting, this camera  
selectively illuminates darker areas while  
retaining the same light level for brighter areas  
to even out the overall brightness.  
Outdoor Visibility range 30M  
Troubleshooting……………………………………………………32  
Specifications………………………………………………………33  
Dimension …………………………………………………………34  
The IR LEDs of the SIR-4260 automatically  
illuminates viewing area in the extreme  
darkness allowing the camera a long-range  
visibility of up to 30 meters.  
COLOR DOME CAMERA  
User Guide  
4
COLOR DOME CAMERA  
User Guide  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Samsung Techwin cares for the environment at all product manufacturing  
stages to preserve the environment, and is taking a number of steps to provide  
customers with more environment-friendly products.The Eco mark represents  
Samsung Techwins will to create environment-friendly products, and indicates  
that the product satisfies the EU RoHS Directive.  
Precautions  
Do not install under extreme  
temperature conditions.  
Do not install in high humidity  
environment.  
Warnings & Cautions  
This information is provided to ensure your safety and to prevent any losses, financial or  
otherwise. Please read it carefully and use the product accordingly.  
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as  
an aerial ladder while providing after-sales service shall be at your expense.  
* Separate the power plug during a thunder storm.  
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and/or personal  
injuries by robbery, fire, natural disaster or something like this type.  
Use only under temperature conditions between  
-10°C and +50°C. Provide good ventilation  
when using in high temperature conditions.  
May lower image quality.  
Do not install under unstable  
lighting conditions.  
Avoid touching the camera lens.  
Warning/Attention/Special Mark Messages  
Ignoring this information may  
Ignoring this information may  
result in material loss and/or  
result in material loss and/or a  
serious personal injuries including  
slight injuries.  
death.  
Severe lighting changes or flickering may  
hinder normal camera operation.  
The lens is the most important component  
of the camera. Be careful not to smear it  
with fingerprints.  
Indicates “Never Allowed.”  
Indicates “No Disassembling.”  
Do not drop the camera or  
subject it to physical shock.  
Never keep the camera face to  
strong light directly.  
May cause a product malfunction.  
May damage the CCD.  
COLOR DOME CAMERA  
User Guide  
6
COLOR DOME CAMERA  
User Guide  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
Overview  
1  
…  
2…  
3…  
Do not expose the camera to  
radioactivity.  
Radioactivity exposure may damage the  
CCD.  
Notes  
54…  
• Exposure to a spotlight or an object emitting strong light may cause smear or  
blooming.  
• Ensure that the power source complies with normal specifications before  
supplying it to the camera.  
• In case of IR LED has been lighted, do not lighten directly eye.  
6…  
7…  
8…  
…  
…  
Components and Accessories  
Pan Base : control panning angle of camera  
Rotate Base : control rotating angle of camera  
X3.6 Vari-focal Lens Module  
 
2
3
4
5
Flush Housing  
Pan Base Holding Screws : fix panned position  
Video output terminal  
RS-485 Control terminal :The detailed decription refers to p14.  
Power input terminal  
6
7
Video Output Terminal to Monitor  
Function Setup switch : display the menu on the screen and move the cursor to  
four directions to confirm status or after changing a  
selected item.  
5
2
6
3
7
4
SCV-2080R  
Instruction Manual……  
Ø5 Tapping Screw 4EA……  
Quick Install Guide………  
Wrench  
Template  
Installation Video Output Cable  
Dome Cover  
COLOR DOME CAMERA  
User Guide  
8
COLOR DOME CAMERA  
User Guide  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
1) You can adjust camera to any direction by using Pan,Tilt, Rotate mechanism.  
• Pan Base moves by 170° to each direction and 340° on the whole.  
• Tilt Base covers total 146° angle(73° to each side).  
Installation  
Notes  
• The angle range of the Rotate Base is the same as that of the Pan Base.But one  
direction range is 195° and another is 145°  
2) Methods of adjustment  
• The installation should be done by qualified service personnel or system installers.  
• If the ceiling material is not strong enough to hold the installation screws, the camera may  
fall off. Reinforce the ceiling as needed.  
Take care not to drop the product during installation. Do not allow anyone to stand below the  
installation area.  
• Wall installation  
After mounting the camera to the wall, loosen the rotate base holding screws.  
Adjust to the correct panning angle.  
Then adjust the tilt angle by rotating the base.  
Once complete re-tighten the rotate base holding screws.  
• Ceiling installation  
1) Remove the dome cover and shield case from the main body by loosening the three  
dome cover screws.  
Mounting Bracket  
After mounting the camera to the ceiling, loosen the rotate base holding screws.  
Adjust to the correct panning angle.  
Then adjust the tilt angle by rotating the base.  
Once complete re-tighten the rotate base holding screws.  
Main Body(Camera)  
Notes  
• When adjusting the rotating angle, loosen rotate base holding screw as follows Figure A. And  
then tighten it again.  
Dome Cover  
• When adjusting the tilting angle, grip the tilt base and adjust tilting angle.  
• When adjusting the panning angle, loosen pan base holding screws as the follows Figure B.  
And then tighten them again.  
• The 2 LED sections can be tilted inside the case to a maximum angle of 73°, this however  
will not alter the illuminated range.  
2) And then remove the main body from the mounting bracket by the four main body screws.  
Rotate Base Holding Screw  
Adjust the panning, tilting and rotate mechanism while checking the position on the monitor  
73°  
145°  
195°  
170°  
Rotate Base  
Tilt Base  
Pan Base  
Pan Base Holding Screw  
Rotate Base Holding Screw  
• When adjusting the tilt mechanism hold the Tilt base and NOT the lens.  
-170°  
COLOR DOME CAMERA  
User Guide  
10  
COLOR DOME CAMERA  
User Guide  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Adjusting varifocal lens zoom and focus  
Connecting to Power  
1) Unlock the zoom (focus) handle by turning anti-clockwise.  
2) Adjust the zoom (focus) by moving the handle to WIDE (NEAR) or TELE (FAR).  
3) After adjustment, tighten the zoom (or the focus) handle, taking care that the adjusted  
position does not change.  
The recommended adaptor specification for  
SCV-2080R is DC 12V/4A.  
Please check the standard power requirement  
before connecting the power.  
Focus Handle  
Zoom Handle  
When the resistance value of copper wire is at [20°C(68°F)]  
Copper wire size(AWG)  
Resistance value(Ω/m)  
Voltage drop(V/m)  
#24(0.22㎟)  
0.078  
#22(0.33㎟)  
0.050  
#20(0.52㎟)  
0.030  
#18(0.83㎟)  
0.018  
0.028  
0.018  
0.011  
0.006  
Connection  
Connecting to Monitor  
• Therefore having an excessively long distance between the power adaptor and the  
camera may affect the camera’s performance.  
Standard voltage for camera operation : DC 12V±10%, AC 24V±10%  
There may be some deviation in voltage drop depending on the type of wire and the  
manufacturer.  
Please connect the video output terminal located on the back of the camera to the monitor.  
• The connection method varies depending on the type of monitor and accessories. Please  
refer to the user's manual for each instrument.  
• Please turn off the power when connecting.  
Notes  
• Please use a power adapter that meets the required standards.  
• Please connect the power after installation.  
Monitor  
CCTV Camera  
COLOR DOME CAMERA  
User Guide  
12  
COLOR DOME CAMERA  
User Guide  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connection  
Using Coaxial Communications  
RS-485 communication control  
• Coaxial Communications System  
• OSD Control method  
Connecting to RS-485 Control Cable  
CAMERA  
SET  
DVR  
MENU / ENTER  
UP KEY  
CONTROLLER  
OSD KEY  
CONTROL CABLE  
WHITE (TRX+)  
BLCAK (TRX-)  
SPEC  
RS-485+  
UP  
JOYSTICK UP  
RS-485-  
DOWN  
LEFT  
DOWN KEY  
LEFT KEY  
JOYSTICK DOWN  
JOYSTICK LEFT  
JOYSTICK RIGHT  
RIGHT  
RIGHT KEY  
Using RS-485 communication will enable you to control the OSD menu from a SAMSUNG  
TECHWIN System Controller or DVR.  
DVR  
(1) Connection to a PC.  
Connect the camera to the PC via a RS-485 converter using RS-485 and a serial cable.  
EX) SERIAL PORT OF THE PC(COM1) SERIAL CABLE RS-485 CONVERTER RS-485  
CONTROL CABLE  
DVD  
(2) Connection to a DVR or System Controller.  
Connect the RS-485 cable to the connection ports of the DVR or System Controller.  
: BNC  
---- : RS-485  
485 Control Board Connection Port  
(+) CONNECTION TERMINAL  
RS-485 Control Port  
WHITE (TRX+)  
– Video Cable  
(-) CONNECTION TERMINAL  
BLACK (TRX-)  
The camera's video output port is connected to the monitor with a BNC coaxial cable,  
shown below : If the distance between the camera and the monitor exceeds the  
recommended maximum, please use an auxiliary video amp.  
* RS-485 Communication establishment initial value  
Camera ID  
BAUD RATE  
9600  
UART MODE  
8-NONE-1  
RET PKT  
ENABLE  
Item  
1
Initial value  
Distance Recommended Cable Specification  
300m  
450m  
600m  
3C2V(RG-59/U)  
5C2V(RG-6/U)  
7C2V(RG-11/U)  
Notes  
• When making a control system to control the camera, please use to the SAMSUNG-T  
PROTOCOL or PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYWELL, SAMSUNG-E  
PROTOCOL.  
• When you connecting to RS-485 control cable, please peel off the outer skin inside the  
RS-485 control cable.  
Notes  
• If the camera is controlled through coaxial communication, please use a video amp intended  
for coaxial communications. Regular video amps do not transfer coaxial signals.  
• In case of SCC-101 connection, change communication mode to  
8-E-1at  
Communication configuration menu. (For more information, refer to SCC-101 manual.)  
COLOR DOME CAMERA  
User Guide  
14  
COLOR DOME CAMERA  
User Guide  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
Menu Configuration  
Menu Setup  
Use the Function Setup switch whithin the camera.  
MAIN SETUP MENU  
DC  
LENS  
…………………  
………  
AGC  
BRIGHTNESS  
SHUTTER  
EXPOSURE  
SENS-UP  
RETURN  
ATW  
OUTDOOR  
INDOOR  
WHITE BAL  
MANUAL  
AWCSET  
Function Setup switch  
ON  
SSDR  
OFF  
1. Press the Function Setup switch.  
• Main setup menu is displayed on the monitor screen.  
HLC  
BACKLIGHT  
SSNR3  
OFF  
BLC  
OFF  
ON  
MAIN SETUP  
Select the function using  
the Function Setup switch.  
1.LENS  
DC  
Change the status using the  
Function Setup switch.  
AUTO  
DAY/NIGHT  
COLOR  
B/W  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
CAM TITLE  
SYNC  
IMAGE ADJ  
5.BACKLIGHT  
6.SSNR3  
PRIVACY  
SPECIAL  
EXIT  
MOTION DET  
DIS  
RETURN  
COMM ADJ  
LANGUAGE  
7.DAY/NIGHT  
8.SPECIAL  
9.EXIT  
AUTO  
SAVE  
NOT SAVE  
RESET  
SAVE  
2. Select a desired function using the Function Setup switch.  
• Place the cursor over a desired item.  
3. Set up a selected item by using the Function Setup switch.  
4.To finish the setting, select ‘EXIT’ and press the Function Setup switch.  
Notes  
• An item with the icon also has sub menus. To select a sub menu, select an item with the  
icon and press the Function Setup switch.  
• An item with the - - - icon is unavailable due to function settings.  
COLOR DOME CAMERA  
User Guide  
16  
COLOR DOME CAMERA  
User Guide  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
SHUTTER :You can select the shutter.  
LENS  
- ---  
: Shutter speed is fixed at 1/60sec(1/50sec)  
- ESC  
: Select this to control the shutter speed automatically. If ESC is selected, the  
shutter speed is automatically controlled depending on the ambient  
illumination of the subject.  
Using this function, you can control the screen brightness.  
1.When the SETUP menu screen is displayed, select LENSby using the Function Setup  
switch so that the arrow indicates LENS.  
2. DC :You can adjust the minimum shutter and maximum value of ESC shutter mode.  
- MANUAL :You can control shutter speed manually.  
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)  
MAIN SETUP  
- A.FLK  
: Select this when you see picture flicker, this can happen when the frequency  
of the local lighting clashes with the camera.  
1.LENS  
DC  
2.EXPOSURE  
Notes  
3.The Lens mode has sub menu items as listed below.  
- BRIGHTNESS :Adjusts the video brightness.  
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.  
- FOCUS ADJ :To adjust the DC lens focus correctly, you must activate the Focus Settings mode  
under each lens menu. Activate the Focus Settings mode, adjust the lens focus,  
and then deactivate the settings mode.  
AGC(AUTO GAIN CONTROL) :The higher the gain level, the brighter the screen - but the  
higher the noise.  
- OFF : Deactivates the AGC function.  
- LOW :Allows automatic gain control from 5.3dB to 32dB.  
- HIGH :Allows automatic gain control from 5.3dB to 37dB.  
EXPOSURE  
MAIN SETUP  
SENS-UP :When it is night or dark, the camera automatically detects the light level and  
maintains a clear picture if this mode is activated.  
- OFF : Deactivates the SENS-UP function.  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
ATW  
- AUTO :Activates the SENS-UP function.  
RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP  
1.When the SETUP menu screen is displayed, select ‘EXPOSURE’ by using the Function Setup switch.  
2. Select a desired mode using the Function Setup switch.  
menu.  
Notes  
EXPOSURE SETUP  
1.BRIGHTNESS  
2.SHUTTER  
3.AGC  
4.SENS-UP  
5.RETURN  
25  
---  
HIGH  
OFF  
• If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by  
increasing or decreasing the shutter speed. (x2 ~ x512)  
• Note that the higher the zoom level, the brighter the screen, but the more likely there will be  
a ghosting effect.  
• It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the  
D-zoom level is increased.  
COLOR DOME CAMERA  
User Guide  
18  
COLOR DOME CAMERA  
User Guide  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
SSDR (Samsung Super Dynamic Range)  
White Balance (White Bal)  
Use the White Balance function to adjust the screen color.  
SSDR illuminates darker spots of an image while retaining the same light level for brighter  
spots to even out the overall brightness of images with high contrast between bright and  
dark spots.  
1.When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function Setup  
switch so that the arrow indicates ‘White Bal’ .  
2. Select a desired mode using the Function Setup switch.  
MAIN SETUP  
1.LENS  
DC  
MAIN SETUP  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
1.LENS  
DC  
ATW  
OFF  
OFF  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
5.BACKLIGHT  
1.When the SETUP menu screen is displayed, select ‘SSDR’ by using the switch so that the  
arrow indicates ‘SSDR’.  
Select one of the following 5 modes, as appropriate for your purpose.  
ATW  
: Select this when the color temperature is between 1,700˚K and 11,000˚K.  
2. Use the switch to change the SSDR level according to the contrast between bright and dark areas.  
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.  
(sodium light inclusion)  
INDOOR  
: Select this when the color temperature is between 4,500˚K and 8,500˚K.  
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by  
using the ATW or AWC mode. After that switch to MANUAL mode, fine-  
tune the White Balance and then press the Function Setup switch.  
AWC SET :To find the optimal luminance level for the current environment, point the  
camera towards a sheet of white paper and press the Function Setup  
switch. If the environment changes, readjust it.  
SSDR ON  
SSDR OFF  
Notes  
BACKLIGHT  
• White Balance may not work properly under the following conditions. In this case select the  
AWC mode.  
When the color temperature of the environment surrounding the subject is out of the control  
range (e.g. clear sky or sunset).  
When the ambient illumination of the subject is dim.  
ꢂ…If the camera is directed towards a fluorescent light or is installed in a place where  
illumination changes dramatically, the White Balance operation may become unstable.  
Unlike conventional cameras, the SCV-2080R is designed to deliver a distinctive subject and  
background at the same time, even when the subject is backlight, by using the features of the  
proprietary W-V DSP chip.  
1.When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function Setup  
switch so that the arrow indicates ‘BACKLIGHT’.  
COLOR DOME CAMERA  
User Guide  
20  
COLOR DOME CAMERA  
User Guide  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
Notes  
MAIN SETUP  
• Because there can be a difference in the effectiveness of HLC according to the amount of  
light area in the screen, optimize the installation angle for the best HLC performance.  
• When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT  
ONLY mode.  
• The HLC is not activated in day light or when bright light is not present at night in NIGHT  
ONLY mode.  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
5.BACKLIGHT  
6.SSNR3  
• BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.  
2. Select a desired mode using the Function Setup.  
SSNR3  
BLC : Enables a user to directly select a desired area from a picture, and to view the  
area more clearly.  
HLC (High Light Compensation) :  
If the scene contains extremely bright light areas such as; from car headlights, the light  
can mask out much of the on-screen detail.  
- LEVEL :Adjust level of the HLC function.  
- LIMIT : Enable to change the operating condition.  
- MASK COLOR/TONE : Change the color / transparency of the masking area.  
(Black, Red, Blue, Cyan, Magenta)  
This function reduces the background noise in a low luminance environment.  
1.When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function Setup  
switch so that the arrow indicates ‘SSNR3’.  
MAIN SETUP  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
5.BACKLIGHT  
6.SSNR3  
ATW  
OFF  
OFF  
ON  
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced  
OFF : Not being used  
7.DAY/NIGHT  
AUTO  
3. Select a desired mode using the Function Setup switch and press the Function Setup switch.  
2. Select a desired mode using the Function Setup switch.  
OFF : Deactivates SSNR3. Noise is not reduced.  
ON :Activates SSNR3 so that noise is reduced.  
Select ‘BLC’ to adjust the area to be  
HLC : Enable the user to change the level,  
limit, mask color/tone and area.  
enhanced then adjust the level.  
3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust the  
noise reduction level.  
LOW  
Notes  
1 2 0  
5
1 7 2  
You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is  
‘OFF’.  
• When adjusting the noise reduction level in the SSNR mode, remember that the higher the  
level set, the more the noise level will be reduced, as will the brightness of the image.  
COLOR DOME CAMERA  
User Guide  
22  
COLOR DOME CAMERA  
User Guide  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
- BURST MODE :You can turn on or off the burst signal on  
B/W mode.  
DAY/NIGHT  
- DURATION :You can select brightness of illumination about changing the day/night mode.  
- DWELL TIME :You can select the duration time about changing the day/night mode. …  
3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s  
You can display pictures in color or black and white.  
1.When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function Setup  
switch so that the arrow indicates ‘DAY/NIGHT’ .  
Color B/W  
2.5 lux  
B/W Color  
5 lux  
10 lux  
Fast  
Slow  
MAIN SETUP  
* The day/night switching point of the  
camera can be adjusted.  
1 lux  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
5.BACKLIGHT  
6.SSNR3  
ATW  
OFF  
OFF  
ON  
Notes  
• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'  
mode and 'AUTO' mode can not be selected.  
7.DAY/NIGHT  
8.SPECIAL  
AUTO  
2. Select a desired mode using the Function Setup switch according to the picture display you want.  
COLOR :The picture is always displayed in color.  
B/W :The picture is always displayed in black and white.  
- IR MODE :When IR LED is turned on in B/W, the objects can  
be clearly identified due to the function that  
decreases screen saturation of objects within a  
short distance.  
· TOP/BOTTOM/LEFT/RIGHT :Adjust the range according to  
the location of objects.  
- IR LEVEL : Select LOW when objects appears within a short distance or select HIGH when  
objects appears within a long distance on the screen.  
AUTO :The mode is switched to ’Color‘ in a normal  
AUTO SETUP  
1.BURST MODE  
2.COLOR->B/W  
DURATION  
DWELL TIME  
3.B/W->COLOR  
DURATION  
DWELL TIME  
4.RETURN  
environment, but switches to ’B/W‘ mode when  
ON  
ambient illumination is low.To set up the switching  
time for AUTO mode, press the Function Setup  
switch.You can turn on or off the burst signal on  
B/W mode.  
FAST  
3SEC  
FAST  
10SEC  
COLOR DOME CAMERA  
User Guide  
24  
COLOR DOME CAMERA  
User Guide  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
IMAGE ADJ :  
SPECIAL  
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ’ by using the Function  
Setup switch so that the arrow indicates ’IMAGE ADJ‘.  
2) Select a desired mode using the Function Setup switch.  
1.When the SETUP menu screen is displayed, select ‘SPECIALby using the Function Setup  
switch so that the arrow indicates ‘SPECIAL.  
IMAGE SETUP  
1. V-REV  
2. H-REV  
OFF  
OFF  
MAIN SETUP  
3. D-ZOOM  
4. FONT COLOR  
5. SHARPNESS  
6. MONITOR  
7. RETURN  
OFF  
WHITE  
ON  
1.LENS  
DC  
2.EXPOSURE  
3.WHITE BAL  
4.SSDR  
ATW  
OFF  
OFF  
ON  
LCD  
5.BACKLIGHT  
6.SSNR3  
V-REV :You can flip the picture vertically on the screen.  
H-REV :You can flip the picture horizontally on the screen.  
D-ZOOM :You can use a digital zoom of x1 ~ x16.  
FONT COLOR :You can change the OSD font color. (White,Yellow, Green, Red, Blue)  
SHARPNESS :As you increase this value, the picture outline becomes stronger and  
clearer.Adjust this value appropriately  
7.DAY/NIGHT  
8.SPECIAL  
9.EXIT  
AUTO  
SAVE  
depending on the sharpness of the  
picture.  
2. Select a desired mode using the Function Setup switch.  
Monitor : Please change the settings value of video  
appropriate to your monitor.  
- LCD : Please select this menu item when using a LCD  
monitor.  
SPECIAL  
1. IMAGE ADJ  
2. CAM TITLE  
3. SYNC  
- CRT : Please select this menu item when using a CRT monitor.  
- USER : Please use this menu item when using a monitor other than standard ones.You  
can change the gamma, PED level, and color gain in the sub menus.  
RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to  
the SETUP menu.  
OFF  
INT  
OFF  
OFF  
OFF  
4. MOTION DET  
5. PRIVACY  
6. DIS  
7. COMM ADJ  
Notes  
8. LANGUAGE  
9. RETURN  
ENGLISH  
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.  
• If you increase the SHARPNESS level too high, the picture may become distorted or noise  
may appear.  
COLOR DOME CAMERA  
User Guide  
26  
COLOR DOME CAMERA  
User Guide  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
CAM TITLE : If you enter a title, the title will appear on the monitor.  
SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL),  
you can synchronize the output phase of multiple  
cameras using the power synchronization function  
(Line-Lock) without using a synchronization signal  
generator.  
- INT : Internal Synchronization Type  
- L/L : Power Synchronization Type, Line-lock  
• Press the Function Setup switch.  
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow  
indicates ‘CAM TITLE’.  
2) Set it to ‘ON’ by using the Function Setup switch.  
CAMERA TITLE SETUP  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
3) Press the Function Setup switch.  
4) Use the Function Setup switch to move to  
a desired letter and select the letter by pressing  
the Function Setup switch. Repeat this to enter  
multiple letters.You can enter up to 15 letters.  
abcdefghijklm  
nopqrstuvwxyz  
- . 0 1 2 3 4 5 6 7 8 9  
You can select a desired phase from 0 to 359 when select 'phase'.  
← → C L R P O S E N D  
Notes  
5) Enter a title, move the cursor to ‘POS’ and  
press the Function Setup switch.The entered  
title appears on the screen. Select the position to  
display the title on the screen by using the Function  
Setup switch and press the Function Setup switch.  
When the position is determined, select ‘END’ and  
press the Function Setup switch to return to the  
SPECIAL menu.  
• When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type  
synchronization.  
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.  
FRONT DOOR  
:
MOTION DET  
This product has a feature that allows you to observe  
movement of objects in 8 different areas on the screen, and  
the words 'MOTION DETECTED' appear on the screen when  
movement is detected.  
Activity can be monitor more efficiently.  
1) When the SPECIAL menu screen is displayed, press the  
Function Setup switch so that the arrow  
indicates MOTION DET.  
2) Set up the mode using the Function Setup switch.  
- SENSITIVITY :You can select up to 8 MD areas.When SENSITIVITY number is high, motion  
detection sensitivity is increased to recognize even small movement.  
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.  
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.  
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.  
- YPOS : Determines the coordinate of the vertical axis for SEL POS.  
- FILLSET : Fills in a selected MD area. The color of the area can be selected from brown,  
orange, blue, cyan, green, yellow, magenta and red.  
Notes  
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if  
you enter one.  
• Only English is available in this mode.  
• If you move the cursor to CLR and press the Function Setup switch, all the letters are  
deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function  
Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be  
inserted and then press the Function Setup switch.  
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.  
COLOR DOME CAMERA  
User Guide  
28  
COLOR DOME CAMERA  
User Guide  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your Camera  
PRIVACY : Mask an area you want to hide on the screen.  
PRIVACY AREA SETUP  
COMM ADJ (Communication Adjustment) :  
This function sets up the camera communication status when controlling the camera  
through an external control device.  
1) When the SPECIAL menu screen is displayed, press the  
Function Setup switch so that the arrow indicates  
1. AREA  
2. MODE  
3. MASK COLOR  
4. MASK TONE  
5. TOP  
AREA1  
OFF  
GREEN  
1
‘COMM ADJ’.  
2) Set up the mode using the Function Setup witch.  
- CAM ID : Determines the camera's identification  
number (between 0 and 255).  
39  
6. BOTTOM  
7. LEFT  
79  
13  
- BAUD RATE :You can select 2400/4800/9600/19200/  
38400/57600 bps.  
- UART MODE :You can select NONE, EVEN or ODD for  
the parity bits.  
8. RIGHT  
9. RETURN  
52  
- RET PKT : Determines whether to send a command back to the controller device when a  
communication control command is sent to the camera.  
- DISP CAM ID : Display camera title on top left corner of the screen.  
- Protocol : Select the communication PROTOCOL.  
(SAMSUNG-T/PELCO-D/PELCO-P/BOSCH/HONEYWELL/VICON/SAMSUNG-E/  
PANASONIC)  
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the  
arrow indicates ‘PRIVACY’.  
2) Set up the mode using the Function Setup switch.  
- AREA :You can select up to 12 PRIVACY areas.  
- MODE : Determines whether to use the area selected in the AREA.  
- MASK COLOR : Determine area color.You can select Green, Red, Blue, Black,White, Gray.  
- MASK TONE :Adjust the brightness of MASK COLOR.  
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.  
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.  
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.  
* Initial value of communication adjustment  
Camera ID BAUD RATE UART MODE  
9600 8-NONE-1  
PET PKT  
ENABLE  
Item  
Initial value  
1
DIS (Digital Image Stabilizer) :  
This function mitigates any picture movement due to external factors such as wind.  
LANGUAGE :You can select the menu language according to your requirements.  
RETURN  
: Select this to save the SPECIAL menu settings and return to the MAIN  
SETUP menu.  
EXIT  
Select a desired EXIT mode using the Function Setup switch.  
Notes  
- SAVE : Save the current settings and exit the MAIN SETUP menu.  
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.  
- RESET : Resets the camera settings to the factory defaults. Language, Communication and Monitor  
settings are not initialized.  
• As the DIS function uses the digital zoom the camera's resolution will decrease.  
• DIS doesn’t operate when background illumination is too low.  
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.  
COLOR DOME CAMERA  
User Guide  
30  
COLOR DOME CAMERA  
User Guide  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Specifications  
SCV-2080RN  
SCV-2080RP  
If you have trouble operating your camera, refer to the following table.  
If the guidelines do not enable you to solve the problem, contact an authorized technician.  
ELECTRICAL  
Input Voltage  
Power Consumption  
VIDEO  
DC 12V 10% / AC 24V 10%  
Max 5W (LED ON)  
• Nothing appears on the screen.  
Check that the power cord and line connection between the camera and monitor are  
fixed properly.  
Check that you have properly connected UTP cable or BNC cable to the camera.  
Imaging Device  
Total Pixels  
Effective Pixels  
Scanning System  
Synchronization  
Frequency  
Horizontal Resolution  
Min. Illumination  
Visibility distance(IR LED)  
S/N (Y Signal)  
1/3 inch, Diagonal 6mm Super HAD CCD  
811(H) x 508(V)  
768(H) x 494(V)  
2:1 Interlace  
Internal /Line-Lock  
H : 15.734KHz V : 59.94Hz  
COLOR : 600TVL, B/W : 700TVL  
LED ON : 0Lux / LED OFF : 0.15Lux(Color, F1.2), 0.0003Lux(Color,SENS-UP x512)  
30m(10EA)  
52dB (Weight On, AGC Off)  
CVBS : 1.0Vp-p, 75Ω composite  
795(H) x 596(V)  
752(H) x 582(V)  
The image on the screen is dim.  
Is lens stained with dirt? Clean your lens with soft, clean cloth.  
Set the monitor to proper condition.  
If the camera is exposed to too strong light, change the camera position.  
H : 15.625KHz V : 50.00Hz  
The image on the screen is dark.  
Adjust the contrast feature of the monitor.  
If you have an intermediate device, set the 75Ω / Hi-z properly.  
Video Output  
LENS  
Zoom Ratio  
Focus Length  
3.6x (Manual)  
2.8 ~ 10.0mm (F1.2)  
Angular Field of View  
PAN / TILT / ROTATE  
Pan / Tilt / Rotate Range  
OPERATIONAL  
Electronic Shutter Speed  
On Screen Display  
SSDR  
Backlight Compensation  
Day & Night  
Gain Control  
H : 94.4°(Wide) ~ 28°(Tele) / V : 69.2°(Wide) ~ 21°(Tele)  
The camera is not working properly, and the surface of the camera is hot.  
Check that you have properly connected the camera to an appropriate power source.  
0°~ 340°/ 0°~ 146°/ 0°~ 340°  
The SENS-UP function does not work.  
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.  
Check that SHUTTER of EXPOSURE SETUP menu is A.FLK’ or ‘MANUAL’.  
1/60 ~ 1/120k sec  
1/50 ~ 1/120k sec  
NTSC : 7 Languages, PAL : 15 Languages  
On / Off (Level adjustable)  
BLC / HLC / OFF  
COLOR / B/W / AUTO (ICR)  
Low / High / Off  
The Motion Detection function does not work.  
Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.  
White Balance  
ATW /Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)  
Color is not correct.  
Check the setting of WHITE BAL SETUP menu .  
SENS-UP (frame Integration)  
Motion Detection  
Privacy Masking  
3D Noise Filter (SSNRIII)  
Digital Zoom  
Digital Image Stabilization(DIS)  
Camera Title  
Sharpness  
Auto /Off (Selectable x2 ~ x512)  
On / Off (8 Programmable zones)  
On / Off (12 Programmable zones)  
On / Off (Level adjustable)  
On / Off (x1 ~ x16)  
On / Off  
On / Off (Displayed 15 Characters)  
On / Off (Level adjustable)  
The screen flickers continually.  
Check that direction of camera turns toward the Sun.  
When coaxial communication is not available:  
Make sure that the camera and monitor are installed within the recommended distance.  
Use the video amplifier equivalent to coaxitron if the recommended installation distance  
is exceeded.  
Flip / Mirror  
Communication  
On / Off  
Coaxial, RS-485  
Coaxial(Pelco), RS-485(SAMSUNG-T, PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH,  
HONEYWELL, SAMSUNG-E)  
Protocol  
ENVIRONMENTAL  
Operating Temperature / Humidity  
MECHANICAL  
-10°C ~ +50°C / 30% ~ 80% RH  
Water Resistance  
IP66  
Dimension (Weight)  
Ø148 x 126mm (1.3Kg)  
The specification for this product may change without prior notice for product improvement.  
COLOR DOME CAMERA  
User Guide  
32  
COLOR DOME CAMERA  
User Guide  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECLARATION OF CONFORMITY  
Dimension  
Application of Council Directive(s)  
2004 / 108 / EC  
Manufacturer's Name  
Manufacturer's Address  
SAMSUNG TECHWIN CO., LTD  
SAMSUNG TECHWIN CO., LTD  
42, SUNGJU-DONG CHANGWON-CITY,  
KYUNGNAM, KOREA, 641-716  
Ø 148mm  
European Representative Name  
European Representative Address  
Equipment Type/Environment  
Model Name  
CCTV Camera  
SCV-2080RP  
Beginning Serial NO.  
C5MR6V3Z200001X  
2010.02.01  
Year of Manufacture  
Conformance to  
EN 55022 : 2006  
EN 50130-4 : 2003  
85mm  
We, the undersigned, hereby declare that the equipment specified above conforms  
to the above Directive(s).  
83.5mm  
85mm  
Manufacturer SAMSUNG TECHWIN CO., LTD  
Signature  
Legal Representative in Europe  
Signature  
Full Name  
Position  
Place  
Full Name  
Position  
Place  
BONJENG GU  
QUALITY CONTROL MANAGER  
CHANGWON, KOREA  
2010.02.01  
Date  
Date  
COLOR DOME CAMERA  
User Guide  
34  
COLOR DOME CAMERA  
User Guide  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Quasar VCR VHQ820 User Guide
Radio Shack Surge Protector 61 2341 User Guide
RCA Clock Radio RP4806 User Guide
RCA Speaker System WSP150 User Guide
Ricoh Two Way Radio 21 1812 User Guide
Rosewill Wheelchair RCTO4BF User Guide
Samsung Cell Phone 426 User Guide
Sanyo Battery Charger UPF383562 User Guide
Schumacher Battery Charger 1010 User Guide
Sears Dryer Accessories 134176300 User Guide