PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurround XT
Digital Natural Image engine
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
BN68-01171B-03
Download from Www.Somanuals.com. All Manuals Search And Download.
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
General Information
Function Description
User Instructions............................................. 2
Checking Parts................................................ 4
Using the Stand-Base..................................... 4
Control Panel ................................................. 5
Connection Panel............................................ 6
Viewing the Remote Control (PS42Q96HD/
PS42Q97HD/PS50Q96HD/PS50Q97HD) ...... 8
Viewing the Remote Control (PS42C9HD/
PS42C96HD/PS50C9HD/PS50C96HD)......... 9
Time Features............................................... 25
Language / Blue Screen / Melody /
Light Effect / Energy Saving /
HDMI Black Level ......................................... 26
Using the Game Mode.................................. 27
Wall- mount adjustment (Sold separately) .... 28
Viewing the Picture in Picture (PIP).............. 29
Screen Burn Protection................................. 30
PC Display
Setting up Your PC Software (Based on
Operation
Switching Your Television On and Off ........... 10
Viewing the Menus........................................ 11
Plug & Play Feature...................................... 11
Viewing an External Signal Sources............. 13
Editing Device Names................................... 14
Windows XP) ................................................ 31
Input Mode (PC)............................................ 32
Setting the PC............................................... 33
Setting the Home Theatre PC....................... 34
Using the DTV Feature
Previewing the DTV Menu System ............... 35
Displaying Programme Information............... 36
Operating the DTV Menu.............................. 37
Channel Control
Storing Channels Automatically .................... 14
Storing Channels Manually........................... 15
Adding / Locking Channels ........................... 16
Sorting the Stored Channels......................... 17
Assigning Names to Channels...................... 17
Fine Tuning Channel Reception.................... 18
LNA (Low Noise Amplifier) ............................ 18
About Anynet+ (PS42Q96HD/PS42Q97HD/PS50Q96HD/PS50Q97HD)
What is Anynet+?.......................................... 47
Connecting Anynet+ Devices........................ 47
Setting Up Anynet+....................................... 48
Scanning and Switching between Anynet+
Devices ......................................................... 48
Recording...................................................... 49
Listening through a Receiver ........................ 50
Check Points before Requesting Service ..... 50
Picture Control
Changing the Picture Standard..................... 19
Customizing the Picture Settings.................. 19
Configuring Detailed Settings on the Picture.. 20
Selecting the Picture Size............................. 21
Selecting the Screen Mode........................... 21
Digital NR / Active Colour / DNIe /
Appendix
Movie Plus .................................................... 22
Freezing the Current Picture......................... 22
Teletext Feature (depending on the model).. 51
Installing the Wall Mount Kit.......................... 53
Setting Up Your Remote Control................... 54
How to assemble the Stand-Base
(depending on the model)............................. 59
Troubleshooting ............................................ 59
Specifications................................................ 60
Sound Control
Sound Features ............................................ 23
Selecting the Sound Mode (depending on
the model)..................................................... 24
☛
➢
Symbols
Press
Important
Note
English - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Cloth-Clean
Warranty Card/
Registration Card/
Safety Guide Manual
Cover-Bottom / Screws (2ea)
(Refer to page 59)
Ferrite Core for Power Cord/
S-Video Cable
Ferrite Core for
Headphones Cable/
Power Cord
Sold Separately
S-Video Cable
PC Cable
Antenna Cable
Scart Cable
Component Cables
Audio Cables
HDMI Cable
Video Cable
PC Audio Cable
HDMI/DVI Cable
Ferrite Core (Power Cord, Headphones Cable, S-Video Cable)
The ferrite core is used to shield the cable from interference.
When connecting a cable, open the ferrite core and clip it
around the cable.
➢
Using the Stand-Base
Two or more people should carry
➢
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
Front (or Side) Panel
Speaker
The product colour and shape may vary depending on the model.
➢
1
SOURCE
4
C/P.
Displays a menu of all of the available input
sources (TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, HDMI3, and
DTV).
Press to change channels. In the on-screen
menu, use the
you use the ▲ and ▼ buttons on the remote
control.
C/P.
buttons as
HDMI3 mode is available only in
PS42Q96HD/PS42Q97HD/PS50Q96HD/
PS50Q97HD models.
➢
5
6
(ENTER)
Press to confirm a selection.
(Power) button
Press to turn the TV on and off.
2
3
MENU
Press to see the on-screen menu of your TV’s
features.
Power Indicator
− Power Off: Blue
− Power On: Off
+
−
Press to increase or decrease the volume.
In the on-screen menu, use the +
−
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
buttons as you use the ◄ and ► buttons on
the remote control.
English - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Panel
Side Panel
1
2
or
3
The product colour and shape may vary depending on the model.
➢
1
2
HDMI IN 3 (PS42Q96HD/PS42Q97HD/
3
Headphones jack
PS50Q96HD/PS50Q97HD)
Connect to the HDMI jack of a device with
HDMI output.
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for
external devices, such as a camcorder or VCR.
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
➢
Rear Panel
1
0
or
Cable Television
Network
6
8
or
2
3
4
5
7
9
The product colour and shape may vary depending on the model.
➢
Whenever you connect an audio or video system to your set, ensure that all elements are
☛
switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
Continued...
English - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
POWER IN
Connect the supplied power cord.
Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
9
HDMI IN 1, HDMI IN 2
− Connect to the HDMI jack of a device with
HDMI output. These inputs can also be used
as a DVI connection with separate analog
audio inputs. An optional HDMI/DVI cable
will be necessary to make this connection.
When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV
allow you to receive left and right audio from
your DVI device. (Not compatible with PC)
− When connecting this product via HDMI or
DVI to a Set Top Box, DVD Player or Games
Console etc, make sure that it has been
set to a compatible video output mode as
shown in the table below. Failure to observe
this may result in picture distortion, image
breakup or no picture.
3
EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Input
Output
Connector
Video Audio(L/R) RGB Video + Audio(L/R)
Only TV or DTV
EXT 1
EXT 2
✔
✔
✔
output is available.
Output you can
choose.
✔
✔
− Do not attempt to connect the HDMI/DVI
connector to a PC or Laptop Graphics Card.
(This will result in a blank screen being
displayed)
DVI IN (HDMI 2) AUDIO L/R
DVI audio outputs for external devices.
4
COMPONENT IN
Audio (AUDIO L/R) and video (Y/PB/PR) inputs
for Component.
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
5
6
0
ANT IN
75Ω Coaxial connector for Aerial/Cable
Network.
Supported modes for HDMI and Component
480i 480p 576i 576p 720p 1080i
7
8
PC IN / AUDIO
Connect to the video and audio output jack on
your PC.
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
X
X
O
X
O
O
X
X
O
O
X
O
O
O
O
O
O
O
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 46)
− When not inserting “CI CARD” in some
channels, “Scramble Signal” is displayed on
the screen.
− The pairing information containing a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has finished, the message “Updating
Completed” is displayed, indicating that the
channel list is now updated.
Insert the CI-Card in the direction marked
on it.
➢
English - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the Remote Control (PS42Q96HD/PS42Q97HD/PS50Q96HD/PS50Q97HD)
This is a special remote control for the visually impaired persons, and has Braille points on the
➢
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
The performance of the remote control may be affected by bright light.
1
2
3
4
5
6
POWER button
(turns the TV on and off)
Number buttons for direct
channel access
One/Two-digit channel
selection
Channel control button
(Refer to page 16)
Selects the TV and DTV
mode directly
Volume increase
Volume decrease
Temporary sound switch-off
h
i
Picture-In-Picture On/Off
Picture effect selection
(Refer to page 19)
Digital subtitle display
Picture freeze
If your remote control is not
functioning properly, take out
the batteries and press the
reset button for about 2~3
seconds.
j
k
l
Re-insert the batteries and
try using the remote control
again.
7
8
Displays the main on-screen Teletext Functions
menu
(Refer to page 51)
9
Returns to the previous
menu
Picture size selection
Electronic Program Guide
(EPG) display
Sound mode selection
Remote control setup
5
Exit from the teletext display
(depending on the model)
@
#
8
0
!
Teletext index
Fastext topic selection
Teletext display/mix both
teletext information and the
normal broadcast
$
%
^
Selects a target device to be
controlled by the Samsung
remote control (TV, DVD,
STB, CABLE, VCR)
Press to backlight the VOL,
CH, and the active source
button (TV, DVD, CABLE,
STB, VCR) on the remote.
Available source selection
Previous channel
DTV menu display
@
*
Teletext size
Teletext mode selection
(LIST/FLOF)
(
c
Teletext sub page
&
P
P
:Teletext next page
:Teletext previous page
d
f
h
i
Teletext cancel
Teletext reveal
Teletext hold
Teletext store
*
(
)
a
Records for Live
Broadcasting
b
c
VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
Next channel
Previous channel
d
e
Exit the on-screen menu
Control the cursor in the
menu
f
g
Use to see information on
the current broadcast
Runs the Anynet+ view
functions and sets up
Anynet+ devices.
Continued...
English - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the Remote Control (PS42C9HD/PS42C96HD/PS50C9HD/PS50C96HD)
This is a special remote control for the visually impaired persons, and has Braille points on the
➢
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
The performance of the remote control may be affected by bright light.
1
2
3
4
5
6
POWER button
(turns the TV on and off)
Number buttons for direct
channel access
One/Two-digit channel
selection
Channel control button
(Refer to page 16)
Selects the TV and DTV
mode directly
Volume increase
Volume decrease
Temporary sound switch-off
h
i
Picture-In-Picture On/Off
Picture effect selection
(Refer to page 19)
Digital subtitle display
Picture freeze
If your remote control is not
functioning properly, take out
the batteries and press the
reset button for about 2~3
seconds.
j
k
l
Re-insert the batteries and
try using the remote control
again.
7
8
Displays the main on-screen Teletext Functions
menu
(Refer to page 51)
9
!
Returns to the previous
menu
TruSurround XT mode
button
Picture size selection
Electronic Program Guide
(EPG) display
Sound mode selection
Remote control setup
Selects a target device to be
controlled by the Samsung
remote control (TV, DVD,
STB, CABLE, VCR)
Press to backlight the VOL,
CH, and the active source
button (TV, DVD, CABLE,
STB, VCR) on the remote.
5
Exit from the teletext display
(depending on the model)
8
0
@
*
Teletext index
Fastext topic selection
Teletext size
Teletext mode selection
(LIST/FLOF)
@
#
$
%
^
(
c
Teletext sub page
P
P
:Teletext next page
:Teletext previous page
d
f
g
Teletext cancel
Teletext reveal
Teletext display/mix both
teletext information and the
normal broadcast
&
h
i
Teletext hold
Teletext store
*
(
)
a
Available source selection
Previous channel
DTV menu display
Selects the HDMI mode
directly
b
c
VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
Next channel
Previous channel
d
e
Exit the on-screen menu
Control the cursor in the
menu
Continued...
f
Use to see information on
the current broadcast
English - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Batteries in the Remote Control
1
Lift the cover at the back of the remote control upward as
shown in the figure.
2
Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese.
➢
3
Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
➢
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
➢
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1
Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
➢
2
Press the
(Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is re-selected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 14 or “Storing Channels Manually” on page 15.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 11.
➢
3
4
To switch the television off, press the
the POWER button on the remote control.
(Power) button (On/Off) on the front of the television or press
To switch the TV on, press the
(Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
English - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the Menus
T V
Picture
: Dynamic
1
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER/OK button to access the icon’s sub-menu.
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER/OK button to enter items in the menu.
Press the ▲/▼/◄/► button to change the selected items.
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
100
45
75
55
50
2
3
4
G
50
R
: Cool1
Detailed Settings
More
Move
Enter
Exit
Press the RETURN button to return to the previous menu.
5
Press the EXIT button to exit from the menu.
The illustration for remote control and OSD (On Screen
Display) shown in this manual has been created based on the
PS42Q96HD model. Even though the configuration is different
from your model, the operation method is the same as in the
illustration.
➢
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
Plug & Play
Start Plug & Play.
If you accidentally select the wrong country for your TV, the
☛
characters on the screen may be wrongly displayed.
OK
Any functions related to Digital TV (DVB) will only work in
☛
Enter
Return
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local dealer if
you can receive DVB-T signals. Although this TV set follows the
DVB-T specification, maintaining compatibility with the future
coming DVB-T digital terrestrial broadcasts is not guaranteed.
Several functions may not be available in some countries.
If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER/OK button.
Plug & Play
Language
English
Deutsch
Français
Italiano
▼
1
Move
Enter
Skip
Plug & Play
2
3
The Language menu will automatically appear after several
seconds.
Select Home Mode
when installing this TV at home.
Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The message Select Home
Mode when installing this TV at home. is displayed.
Press the ◄ or ► button to select Shop or Home, then press
the ENTER/OK button. The message to check the connected
status of the antenna is displayed.
Shop
Home
Move
Enter
Skip
4
Plug & Play
The default selection is Home.
We recommend setting the TV to Home mode for the best
picture in your home environment.
Shop mode is only intended for use in retail environments.
➢
Check antenna input.
➢
OK
➢
Enter
Skip
If the unit is accidentally set to Shop mode, and you want to
➢
return to Dynamic (Home) mode, press the Volume button
and then hold down the MENU button for five seconds on
the TV panel.
Plug & Play
Country
Move
Belgium
France
Germany
Italy
5
Make sure that the antenna is connected to the TV.
Press the ENTER/OK button. The Country menu is displayed.
▼
Enter
Skip
Continued...
English - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER/OK button.
The message Some DTV functions may not be available.
Digitally Scan? is displayed.
If your country supports the DTV functions, the message is
not displayed. Then you can follow the instructions from step
12. When the local service provider does not support DTV
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
properly.When No is selected, follow the instructions from step
7 to 10. When Yes is selected, follow the instructions from
step 11.
Select No pressing the ◄ or ► button, then press the
ENTER/OK button. Auto Store menu is displayed.
Press the ENTER/OK button to start search the channels.
The channel search will start and end automatically. After all the
available channels are stored, Clock Set menu is automatically
displayed. Press the ENTER/OK button.
Plug & Play
Some DTV functions may not be available.
Digitally Scan?
Yes
No
Move
Enter
Plug & Play
--
Skip
Auto Store
P
1
C
40 MHz
0
%
Start
7
8
Enter
Skip
Plug & Play
Year Hour
Clock Set
Month Day
Minute
00
01
01
2007
12
To stop the search before it has finished, press the
ENTER/OK button with Stop selected.
➢
9
Press the ◄ or ► button to select Month, Day, Year, Hour, or
Adjust
Move
Enter
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
➢
Plug & Play
directly by pressing the numeric buttons on the remote
control.
10 Press the ENTER/OK button to confirm your setting. The
message Enjoy your viewing is displayed. When you have
finished, press the ENTER/OK button.
0%
Services found: 0
Channel:
Start
-
Even if the ENTER/OK button is not pressed, the message
➢
will automatically disappear after several seconds.
Skip
11 Select Yes pressing the ◄ or ► button, then press the
ENTER/OK button. Auto Store menu is displayed.
Plug & Play
12 Press the ENTER/OK button to start search the analog
channels. The analog channel search will start and end
automatically. After all the available analog channels are stored,
the screen for searching digital channels is automatically
displayed.
Scanning for digital services...
29%
Services found: 6
Channel: 35
Stop
To stop the search before it has finished, press the
➢
ENTER/OK button with Stop selected.
Skip
13 Press the ENTER/OK button to start search the digital
channels. The digital channel search will start and end
automatically. After all the available digital channels are stored,
the screen to select a time zone is displayed depending on the
country.
Plug & Play
The Iberian Peninsula and Balears Islands
Canarian Islands
To stop the search before it has finished, press the
➢
ENTER/OK button with Stop selected.
If the DTV channel is updated, the Source in the source list
➢
of the Input menu is automatically changed to DTV.
For detailed descriptions about DTV channel update, refer
Move
Select
Skip
➢
to page 37 of this manual.
14 Press the ▲ or ▼ button to select required time zone, then
press the ENTER/OK button. The screen for setting the time is
displayed. Press the ENTER/OK button.
Continued...
English - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
15 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Plug & Play
Set the current time.
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
➢
Month Day
Year
2007
01
15
Hour Minute
12 00
16 Press the ENTER/OK button to confirm your setting. The
message Enjoy your viewing is displayed. When you have
finished, press the ENTER/OK button.
Adjust
Move
Select
Skip
Even if the ENTER/OK button is not pressed, the message
will automatically disappear after several seconds.
➢
Enjoy your viewing
OK
If you want to reset this feature …
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ENTER/OK button again to select Plug & Play.
T V
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
3
The message Start Plug & Play is displayed.
PC
Home Theatre PC : Off
Light Effect
: Off
More
Move
Enter
Return
Viewing an External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
T V
Input
Source List
Edit Name
Anynet+
: TV
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button.
3
4
Press the ENTER/OK button again to select Source List.
Press the ▲ or ▼ button to select the signal source, then press
the ENTER/OK button.
Move
Enter
Return
Available signal sources: TV, Ext.1, Ext.2, AV, S-Video,
T V
Source List
Component, PC, HDMI1, HDMI2, HDMI3, DTV
TV
Ext.1
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
HDMI3 mode is available only in PS42Q96HD/
➢
Ext.2
AV
PS42Q97HD/PS50Q96HD/PS50Q97HD models.
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
DTV
Move
Enter
Return
You can select these options simply by pressing the SOURCE
button on the remote control.
➢
➢
To watch television programme again, press the TV/DTV button
and select the channel number required.
English - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing Device Names
You can give a name to the external source.
Input
: TV
T V
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
Source List
Edit Name
Anynet+
ENTER/OK button.
3
4
5
Press the ▲ or ▼ button to select Edit Name, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER/OK button.
Select the required device by pressing ▲ or ▼, then press the
ENTER/OK button.
Move
Enter
Return
T V
Edit Name
Available device names: VCR, DVD, D-VHS, Cable STB, HD
STB, Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC.
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
: −−−−
: VCR
: DVD
: D-VHS
: Cable STB
: HD STB
: Satellite STB
6
Press the EXIT button to exit.
HDMI3 mode is available only in PS42Q96HD/
PS42Q97HD/PS50Q96HD/PS50Q97HD models.
➢
:
: −−−−
▼
Move
Enter
Return
Storing Channels Automatically
Not available in DTV or external input mode.
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do
not wish to watch.
T V
Channel
➢
Belgium
:
Country
Auto Store
Manual Store
France
Germany
Italy
Netherlands
Spain
▼
Channel Manager
Sort
Name
Fine Tune
LNA
: O
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Press the ENTER/OK button again. The available countries are
Move
Enter
Channel
Return
T V
3
4
Country
Auto Store
Manual Store
Channel Manager
Sort
Name
: Belgium
listed.
Select your country by pressing the ▲ or ▼ button, then press
the ENTER/OK button.
Even though you have changed the country setting in this
➢
Fine Tune
LNA
: Off
menu, the country setting for DTV is not changed. Use the
Plug & Play function to change the country setting for DTV.
(Refer to page 11 to 13)
Move
Enter
Return
5
6
Press the ▲ or ▼ button to select Auto Store, then press the
ENTER/OK button.
Press the ENTER/OK button again to start the search.
The search will end automatically.
Auto Store
--
P
1
C
40 MHz
0
%
To stop the search before it has finished, press the MENU
or the ENTER/OK button.
➢
Start
Enter
Return
English - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Channels Manually
Not available in DTV or external input mode.
You can store television channels, including those received via
cable networks.
T V
Channel
➢
Country
Auto Store
Manual Store
: Belgium
When storing channels manually, you can choose:
Channel Manager
Sort
Whether or not to store each of the channels found.
The programme number of each stored channel which you wish
to identify.
Name
Fine Tune
LNA
: Off
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select Manual Store, then press
the ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
When you are satisfied with your setting, press the ENTER/OK
Move
Enter
Return
T V
Manual Store
: P
3
4
5
Programme
Colour System
Sound System
Channel
Search
Store
1
: Auto
: BG
: C
: 63 MHz
: ?
4
button.
6
Press the EXIT button to exit.
Move
Enter
Return
Programme (Programme number to be assigned to a channel)
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
Colour System: Auto/PAL/SECAM/NTSC4.43
➢
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
Search (When you do not know the channel numbers)
➢
➢
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER/OK button.
Channel mode
☛
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding / Locking Channels
Not available in DTV or external input mode.
Using the Channel Manager, you can conveniently lock or add
channels.
T V
Channel
➢
Country
Auto Store
Manual Store
: Belgium
Channel Manager
Sort
Name
Fine Tune
LNA
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
: Off
3
Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER/OK button.
Move
Enter
Return
Adding channels
Using the Channel List, you can add channels.
T V
Channel Manager
Channel List
Child Lock
: Off
4
5
Select Channel List by pressing the ENTER/OK button.
Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER/OK button
to add the channel.
If you press the ENTER/OK button again, the ( ) symbol
next to the channel disappears and the channel is not
added.
➢
Move
Enter
Return
1 / 10
Locking channels
This feature allows you to prevent unauthorized users, such as
Channel List
P
1
C 4
children, from watching unsuitable programmes by muting out video
and audio.
Prog.
▲
0
1
2
3
4
5
6
7
8
9
C
C 4
C 24
C 2
C 5
C 80
C 7
C 36
C 52
C 11
--
6
7
8
9
Press the ▲ or ▼ button to select Child Lock, then press the ENTER/
OK button.
Select On by pressing the ▲ or ▼ button, then press the ENTER/OK
button.
Press the ▲ or ▼ button to select Channel List, then press the
ENTER/OK button.
▼
Add
Lock
Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a
channel to be locked, and press the ENTER/OK button.
Move
Page
Enter
Return
If you press the ENTER/OK button again, the ( ) symbol next to
the channel disappears and the channel lock is canceled.
➢
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢
You can select these options simply by pressing the CH LIST
button on the remote control.
➢
English - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Sorting the Stored Channels
Not available in DTV or external input mode.
This operation allows you to change the programme numbers
of the stored channels.
T V
Channel
➢
Country
Auto Store
Manual Store
: Belgium
This operation may be necessary after using the auto store.
Channel Manager
Sort
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Name
Fine Tune
LNA
: Off
3
4
5
Press the ▲ or ▼ button to select Sort, then press the ENTER/
OK button.
Select the channel that you wish to move by pressing the ▲ or
▼ button, then press the ENTER/OK button.
Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The channel is moved to its new
position and all other channels are shifted accordingly.
Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
Move
Enter
Return
T V
Sort
Prog.
Ch.
Name
0
1
2
3
4
C−−
C76
C5
C6
C7
6
7
Press the EXIT button to exit.
Move
Enter
Return
Assigning Names to Channels
Not available in DTV or external input mode.
T V
Channel
➢
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
Country
Auto Store
Manual Store
: Belgium
Channel Manager
Sort
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Name
Fine Tune
LNA
: Off
3
4
5
Press the ▲ or ▼ button to select Name, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select the channel to be assigned to
a new name, then press the ENTER/OK button.
Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER/OK button.
Repeat steps 4 to 5 for each channel to be assigned to a new
name.
Move
Enter
Return
T V
Name
Prog.
Ch.
Name
0
1
2
3
4
C−−
C76
C5
C6
C7
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
6
7
Press the EXIT button to exit.
Move
Enter
Return
English - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine Tuning Channel Reception
Not available in DTV or external input mode.
T V
Channel
➢
If the reception is clear, you do not have to fine tune the
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
Country
Auto Store
Manual Store
: Belgium
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Move
Enter
Return
3
4
Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER/OK button.
To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER/OK button.
Fine Tune
P
1
+3
Reset
Save
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER/OK button.
➢
Adjust
Return
5
Press the EXIT button to exit.
Fine Tune Store will change the colour of the Channel OSD
➢
(On Screen Display) from White to Red and add the “*”
mark.
P
1 *
Mono
Picture
: Dynamic
: Custom
: Off
Sound
SRS TS XT
:
−− −−
LNA (Low Noise Amplifier)
This function is very useful in the situation that the TV is used
in weak signal.
LNA amplifies the TV signal in the weak signal area, a low-noise
preamplifier boosts the incoming signal.
T V
Channel
: Belgium
Country
Auto Store
Manual Store
Channel Manager
Sort
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
Name
Fine Tune
LNA
: Off
3
4
5
Press the ▲ or ▼ button to select LNA, then press the ENTER/
OK button.
Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
Move
Enter
Return
Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as On or Off.
➢
English - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
T V
Picture
: Dynamic
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
100
45
75
55
50
1
2
3
4
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Press the ENTER/OK button again to select Mode.
G
50
R
: Cool1
Select the required mode by pressing the ▲ or ▼ button, then
Detailed Settings
press the ENTER/OK button.
Available modes: Dynamic, Standard, Movie
More
Move
Enter
Return
The settings values may vary depending on the input
source. (ex. RF, Video, Component, PC, or HDMI)
➢
T V
Picture
5
Press the EXIT button to exit.
Dynamic
:
Standard
Movie
Mode
Contrast
Brightness
Sharpness
Colour
100
45
75
55
50
Tint
G
50
R
Colour Tone
Detailed Settings
: Cool1
More
Move
Enter
Return
You can select these options simply by pressing the P.MODE
button on the remote control.
Choose Dynamic for viewing the TV during the day or
➢
➢
when there is bright light in the room.
Choose Standard for general TV watching mode.
Choose Movie when viewing the movie.
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
T V
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
100
1
2
3
4
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Press the ENTER/OK button again to select Mode.
45
75
55
50
G
50
R
: Cool1
Select the required mode by pressing the ▲ or ▼ button, then
Detailed Settings
press the ENTER/OK button.
Available modes: Dynamic, Standard, Movie
More
Move
Enter
Return
5
6
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
When you are satisfied with your setting, press the ENTER/OK
button.
T V
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
100
45
75
55
50
7
Press the EXIT button to exit.
G
50
Cool2
:
Cool1
Contrast – Brightness – Sharpness – Colour – Tint
Detailed Settings
Normal
Warm1
Warm2
In TV, AV, S-Video modes of the PAL system, you cannot
use the Tint Function.
➢
More
Move
Contrast – Brightness – Colour Tone : PC Mode
Enter
Return
Press the ◄ or ► button until you reach the optimal setting.
Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.
➢
Reset: Cancel/OK
Select OK. You can return to the factory defaults picture settings.
The reset function is set for each picture mode and colour tone.
➢
English - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Detailed Settings on the Picture
You can set detailed picture settings.
T V
Picture
: Movie
1
2
3
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER/OK button.
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
80
65
35
35
50
G
50
R
: Warm2
4
Select the required option by pressing the ▲ or ▼ button, then
Detailed Settings
press the ENTER/OK button.
More
Move
Available options: Black Adjust, Dynamic Contrast, Gamma,
White Balance, My Colour Control, Edge Enhancement,
Colour Space
Enter
Return
T V
Detailed Settings
5
When you are satisfied with your setting, press the ENTER/OK
button.
Press the EXIT button to exit.
Black Adjust
Dynamic Contrast : Low
Gamma
White Balance
My Colour Control
Edge Enhancement : Off
Colour Space
: Off
:
0
6
When the picture mode is set to Movie or Standard, Detailed
Settings can be selected.
: Wide
➢
If DNIe is Off, the Detailed Settings cannot be selected when
the Picture mode is in Standard mode.
➢
Move
Enter
Return
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the color temperature for more natural picture colors.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press
the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
My Colour Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences.
Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press
the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted colours will be reset to the factory defaults.
Edge Enhancement: Off/On
You can emphasize object boundaries.
Colour Space: Auto/Wide
You can set the colour reproduction space for the input signal to Auto or Wide.
English - 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Picture Size
You can select the picture size which best corresponds to your
viewing requirements.
T V
Picture
Size
More
: Auto Wide
: 16 : 9
: Auto
: On
: Off
: On
1
2
3
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Press the ▲ or ▼ button to select Size, then press the ENTER/
OK button.
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
: OK
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Move
Enter
Return
Available options: Auto Wide, 16:9, Wide Zoom, Zoom, 4:3,
Just Scan
T V
Size
Auto Wide: Expanding and pulling up the picture from 4:3
to 16:9 ratio.
16:9: Sets the picture to 16:9 wide mode.
Wide Zoom: Magnify the size of the picture more than 4:3.
Move the screen up/down using the ▲ or ▼ button after
Auto Wide
16:9
Wide Zoom
Zoom
4:3
Just Scan
selecting the
by pressing the ► or ENTER/OK button.
Zoom: Magnify the size of the picture vertically on screen.
4:3: Sets the picture to 4:3 normal mode.
Just Scan: Displays the input scenes as they are without
any cutoff when HDMI 720p, 1080i signals are input.
Move
Enter
Return
With the HDMI Just Scan picture size, depending on
the AV devices, the screen may be cut off or a specific
colour appears on the screen.
➢
5
Press the EXIT button to exit.
You can change the picture size simply by pressing the
➢
P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
➢
➢
Positioning and Sizing the screen using Zoom
Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
Move the screen up/down using the ▲ or ▼ button after selecting the
by pressing the ◄ or ►
by pressing the ◄ or ►
button.
Resize the screen vertically using the ▲ or ▼ button after selecting the
button.
Selecting the Screen Mode
When setting the picture size to Auto Wide in a 16:9 wide TV,
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this
function is intended for users to select it.
T V
Picture
Size
More
: Auto Wide
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
: 16 : 9
: Off
: On
: Off
: On
1
2
3
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Press the ▲ or ▼ button to select Screen Mode, then press
the ENTER/OK button.
: OK
Move
Enter
Return
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: 16:9, Wide Zoom, Zoom, 4:3
16:9: Sets the picture to 16:9 wide mode.
Wide Zoom: Magnify the size of the picture more than 4:3.
Zoom: Magnify the size of the picture vertically on screen.
4:3: Sets the picture to 4:3 normal mode.
5
6
When you are satisfied with your setting, press the ENTER/OK button.
Press the EXIT button to exit.
English - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital NR / Active Colour / DNIe / Movie Plus
T V
Picture
1
2
3
Press the MENU button to display the menu.
Press the ENTER/OK button to select Picture.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Digital NR, Active Colour, DNIe, Movie
Plus
Size
More
: Auto Wide
: 16 : 9
: Auto
: On
: Off
: On
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
: OK
4
When you are satisfied with your setting, press the ENTER/OK
button.
Move
Enter
Return
5
Press the EXIT button to exit.
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
Active Colour: Off/On
If you turn on this option, the colors of the sky and grass will be stronger and clearer for a more vivid
on-screen picture.
This function is not available in PC mode.
This function is not available in Movie and Standard mode.
DNIe: Off/Demo/On
➢
➢
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
➢
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives
brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your
eyes.
This function is not available in PC mode.
Movie Plus: Off/On (PS42Q96HD/PS42Q97HD/PS50Q96HD/PS50Q97HD)
➢
You can view more natural skin and clear text even in fast moving scenes.
The Wide Zoom, Zoom and Just Scan mode is not supported.
➢
Freezing the Current Picture
You can freeze the picture when watching a television
programme simply by pressing the “STILL” button. To return to
normal viewing, press it again.
This function will automatically cancel five minutes later.
➢
English - 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Features
T V
Sound
: Custom
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the
ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Mode, Equalizer, SRS TS XT, Auto Volume,
Internal Mute, Reset (If Game Mode is On)
When you are satisfied with your setting, press the ENTER/OK
Mode
Equalizer
SRS TS XT
Auto Volume
Internal Mute
Sound Select
Reset
: Off
: Off
: Off
: Main
3
4
Move
Enter
Return
button.
5
Press the EXIT button to exit.
< If Game Mode is On >
Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used when
watching a given broadcast.
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control
the sound quality.
T V
Sound
Mode
: Custom
Equalizer
SRS TS XT
Auto Volume
Internal Mute
Sound Select
Reset
: Off
: Off
: Off
: Main
If you make any changes to these settings, the sound mode
is automatically switched to Custom.
➢
SRS TS XT: Off/On
Move
Enter
Return
TruSurround XT is a patented SRS technology that solves
the problem of playing 5.1 multichannel content over
two speakers. TruSurround delivers a compelling, virtual
surround sound experience through any two-speaker
playback system, including internal television speakers. It is
fully compatible with all multichannel formats.
T V
Equalizer
R
+
+
0
0
-
TruSurround XT, SRS and
-
➢
L
Symbol are trademarks of SRS Labs,
Inc. TruSurround XT technology is
incorporated under license from SRS
Labs, Inc.
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
Move
Adjust
Return
You can select these options simply by pressing the SRS
button on the remote control. (PS42C9HD/PS42C96HD/
PS50C9HD/PS50C96HD)
➢
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and
so it is not easy to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of the desired channel by lowering the
sound output when the modulation signal is high or by raising the sound output when the modulation
signal is low.
Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The
+,
- and MUTE buttons do not operate when the Internal Mute is set to On.
➢
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting
the equalizer resets the equalizer setting to the factory defaults.
TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
English - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and
output of the audio signal. When power is switched on, the
mode is automatically preset to either “DUAL-I” or “Stereo”,
depending on the current transmission.
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Mono
(Normal)
Regular + NICAM Mono
NICAM Stereo
NICAM
NICAM
Stereo
NICAM
stereo
Mono
(Normal)
NICAM
dual-1
NICAM
dual-2
Mono
(Normal)
NICAM DUAL-I/II
Regular broadcast
(Standard audio)
Mono (Normal use)
A2
Stereo
Bilingual or DUAL-I/II
Dual I
Stereo
Dual II
Mono
Stereo
(Forced mono)
If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
If the stereo signal is weak and automatic switching occurs, switch to Mono.
➢
When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the
panel (front or side). If the mono sound comes out only from left speaker, press the DUAL I-II
button.
English - 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Features
T V
T V
T V
Setup
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select Time, then press the
ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Clock Set, Sleep Timer, Timer 1, Timer 2,
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
3
4
PC
Home Theatre PC : Off
Light Effect
: Off
More
Move
Enter
Return
Timer 3
Time
5
When you are satisfied with your setting, press the ENTER/OK
button.
Press the EXIT button to exit.
Clock Set
You can set the television clock so that the current time is
displayed when pressing the INFO button on the remote control.
You must also set the time if you wish to use the automatic on
or off timers.
− Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
Clock Set
Sleep Timer
Timer 1
Timer 2
Timer 3
: 00 : 00
: Off
: Inactivated
: Inactivated
: Inactivated
6
Move
Enter
Return
Timer 1
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
➢
On Time
00
:
00
00
No
No
Off Time
00
:
In the event of a power interruption or the set being turned
off at the supply, the settings for the Clock will be lost.
➢
Repeat
Once
Volume
10
Sleep Timer
Programme
01
You can select a time period of between 30 and 180 minutes
after which the television automatically switches to standby
mode.
− Select the preset time interval (Off, 30, 60, 90, 120, 150, or
180) for staying on by pressing the ▲ or ▼ button.
Move
Adjust
Return
Timer 1 / Timer 2 / Timer 3
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
☛
On Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Off Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun.
Volume : Select the required volume level.
Programme : Select the required channel.
You can set the hour, minute, and channel directly by pressing the number buttons on the remote
control.
➢
Auto Power Off
☛
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only available in timer “On” mode and prevents
overheating, which may occur if a TV is on for too long time.
English - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Language / Blue Screen / Melody / Light Effect /
Energy Saving / HDMI Black Level
T V
Setup
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Language, Blue Screen, Melody, Light
Effect, Energy Saving, HDMI Black Level
When you are satisfied with your setting, press the ENTER/OK
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
3
4
PC
Home Theatre PC : Off
Light Effect
: Off
More
Move
Enter
Return
button.
T V
Setup
5
Press the EXIT button to exit.
More
Language
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level : Low
PIP
It is variable depending on the model. When you start using the
television for the first time, you must select the language which
will be used for displaying menus and indications.
Screen Burn Protection
Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background. If
you wish to continue viewing the poor picture, you must set the
Blue Screen to Off.
Move
Enter
Return
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
Light Effect: Off/Standby Mode On/Watching Mode On/On
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
− Off: The blue LED is always off.
− Standby Mode On: The blue LED lights while in Standby mode and it turns off when your TV is
turned on.
− Watching Mode On: The blue LED lights when watching TV and it turns off when your TV is
turned off.
− On: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
Energy Saving: Off/Low/Medium/High
➢
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
− Off: Switches off the Energy Saving mode.
− Low: Operates in standard mode regardless of the surrounding illumination.
− Medium: Enters Medium power saving mode regardless of the surrounding illumination.
− High: Enters maximum power saving mode regardless of the surrounding illumination.
HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low color, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the externel input connects to HDMI(RGB signals).
➢
English - 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Game Mode
When connecting to a game console such as PlayStationTM or
XboxTM, you can enjoy a more realistic gaming experience by
selecting game menu.
T V
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
PC
Home Theatre PC : Off
3
4
5
Press the ▲ or ▼ button to select Game Mode, then press the
ENTER/OK button.
Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
Light Effect
: Off
More
Move
Enter
Return
Press the EXIT button to exit.
To disconnect the game console and connect another external device, cancel game mode in the
picture menu.
➢
If you display the TV menu in Game mode, the screen shakes slightly.
Game Mode is not available in TV mode.
If Game Mode is On :
➢
➢
➢
Picture Mode is automatically changed to Standard and users cannot change the mode.
Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
The Reset Sound function is activated. Selecting the Reset function after setting the
equalizer resets the equalizer setting to the factory defaults.
English - 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall- mount adjustment (Sold separately)
Once the wall mount is installed, the position of your TV can be easily adjustable.
Rear Panel
Auto Wall-Mount
Serial Cable(1P to 1P)(Not supplied)
Entering the menu
T V
Setup
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select Wall-Mount Adjustment,
then press the ENTER/OK button.
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level : Low
PIP
2
3
Screen Burn Protection
Adjust to the desired position using the ▲/▼/◄/► buttons.
Press the EXIT button to exit.
If you press an arrow button when no OSD is displayed on the
TV screen, the Adjustment screen appears.
When you turn the power off, your TV moves to the initial
installation position.When you turn the power on, your TV
moves to the last remembered position you adjusted.
➢
➢
Move
Enter
Return
Wall-Mount Adjustment
Position1
Position
Using the remote Control Buttons
Button
Operations
1
2
3
INFO
Wall-mount
angle
adjustment
Adjust
Center
Exit
Tilt Up, Tilt Down, Move
right, Move left
Moves to the initial
installation position
Reset
Remembers 3 positions
with the Red, Green and
Yellow buttons.
Moves to the remembered
position using these 3 color
buttons.
Remembering
the position and
moving to the
remembered
position
(Red) (Green) (Yellow)
For installation, refer to the Installation Manual provided.
For product installation and the installation and moving of the wall mount, make sure to consult a
specialized installation company.
➢
➢
This installation manual is to be used when attaching the wall mount to a wall. When attaching to
other building materials, please contact your nearest dealer.
➢
English - 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this
way you can watch TV program or monitor the video input from
any connected devices.
T V
Setup
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level : Low
PIP
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
Screen Burn Protection
ENTER/OK button.
3
4
Press the ▲ or ▼ button to select PIP, then press the ENTER/
OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Move
Enter
PIP
Return
T V
Available options: PIP(On/Off), Source, Size, Position,
Programme
When you are satisfied with your setting, press the ENTER/OK
button.
PIP
Source
Size
Position
Programme
: On
: TV
:
:
: P
5
1
6
Press the EXIT button to exit.
PIP: On/Off
You can activate or deactivate the PIP function.
Move
Enter
Return
You can select these options simply by pressing the PIP
button on the remote control.
➢
Source: TV/Ext.1/Ext.2/AV
You can select a source of the sub-picture.
Size:
/
/
You can select a size of the sub-picture.
If main picture is in PC and Component mode, Size is not
available.
➢
Position:
/
/
/
You can select a position of the sub-picture.
Programme
You can select a channel of the sub-picture only when the Source is set to TV.
Table of PIP Settings
X - This PIP combination is not available.
O - This PIP combination is available.
Sub
TV analog Ext.1 Ext.2 AV S-Video Component HDMI PC TV digital
Main
Component
HDMI
PC
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
English - 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in
minutes.
T V
T V
T V
Setup
More
Wall-Mount Adjustment
Energy Saving : Off
HDMI Black Level : Low
PIP
Screen Burn Protection
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Move
Enter
Return
3
4
Press the ▲ or ▼ button to select Screen Burn Protection,
then press the ENTER/OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Side Gray
: Off
Available options: Pixel Shift, All White, Signal Pattern, Side
Gray
5
When you are satisfied with your setting, press the ENTER/OK
button.
6
Press the EXIT button to exit.
Move
Enter
Return
Pixel Shift: Using this function, you can minutely move pixels
on the PDP in horizontal or vertical direction to minimize after
image on the screen.
Pixel Shift
: On
Pixel Shift
Horizontal Dot
Vertical Line
Time
: 2
: 2
: 2 min
− Set Pixel Shift to On by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
− Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
Available options: Horizontal Dot, Vertical Line, Time
Optimum condition for pixel shift;
➢
Move
Enter
Return
TV/Ext/AV/S-Video/
PC
Component/HDMI/DTV
Horizontal Dot
Vertical Line
Time (minute)
1
1
2
2
2 min
2 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
➢
All White: This function helps remove after images on the screen by changing the colour of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
Signal Pattern: This function helps remove after images on the screen by moving all the pixels on
the PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either All White or Signal Pattern function. Although
both of the two functions remove after images on the screen, Signal Pattern is more effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution of the
function, repeat the function again.
➢
➢
Press any button on the remote control to cancel this feature.
➢
English - 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer
are shown below. But the actual screens on your PC will
probably be different, depending upon your particular
version of Windows and your particular video card. But even
if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your
computer manufacturer or Samsung Dealer.)
1
Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
2
Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
3
4
Click on Advanced. A new settings dialog box will be
displayed.
Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of
setting the Screen refresh rate.
5
Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic re-booting may commence at this moment.
English - 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
PS42Q96HD/ PS50Q96HD/
Vertical Horizontal PS42Q97HD/ PS50Q97HD/
Vertical Horizontal
frequency frequency
Video
Signal
Resolution
(Dot X Line)
polarity
polarity
PS42C9HD/
PS50C9HD/
(Hz)
(kHz)
PS42C96HD PS50C96HD
640 x 350
720 x 400
70.086
70.087
59.940
70.000
72.809
75.000
60.317
70.000
72.188
75.000
60.004
70.069
72.000
75.029
60.015
31.469
31.469
31.469
35.000
37.861
37.500
37.879
43.750
48.077
46.875
48.363
56.476
57.672
60.023
47.712
N
P
P
N
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
N
N
N/P
N
N/P
N
640 x 480
800 x 600
N
N
P
P
IBM PC / AT
Compatible
N/P
P
N/P
P
P
P
N
N
N
N
1024 x 768
1360 x 768
N/P
P
N/P
P
P
P
(N: Negative / P: Positive)
The interlace mode is not supported.
The television might operate abnormally if a non-standard video format is selected.
480i/p, 576i/p, 720p, or 1080i is not available in PC mode.
For the PS42Q96HD/PS42Q97HD/PS42C9HD/PS42C96HD, PC text quality is optimum in XGA
mode (1024 x 768@60Hz).
For the PS50Q96HD/PS50Q97HD/PS50C9HD/PS50C96HD, PC text quality is optimum in WXGA
mode (1360 x 768@60Hz).
(The three pixels each on the left and right are grayed at the resolution setting of 1360 x 768@60Hz.
This is not a mechanical problem but a result caused by the pixel difference between the standard
resolution and the PDP panel.)
English - 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PC
Preset to the PC mode by pressing the SOURCE button.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select PC, then press the ENTER/
OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Image Lock, Position, Auto Adjustment,
Image Reset
When you are satisfied with your setting, press the ENTER/OK
button.
Press the EXIT button to exit.
Image Lock: Coarse/Fine
T V
T V
T V
T V
Setup
➢
1
2
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
3
4
PC
Home Theatre PC : Off
Light Effect
: Off
More
Move
Enter
PC
Return
5
Image Lock
Position
Auto Adjustment
Image Reset
6
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust the
frequency as best as possible (coarse) and Fine-tune again.
After the noise has been reduced, re-adjust the picture so that it
is aligned on the center of screen.
Move
Enter
Return
Return
Return
Image Lock
Coarse
Fine
50
31
1
Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER/OK button.
2
Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER/OK button.
Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
Move
Enter
1
2
Adjust the position by pressing the ▲/▼/◄/► button.
Press the ENTER/OK button.
Position
Auto Adjustment
Auto adjustment allows the PC screen of set to self-adjust to the
incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Image Reset
You can replace all image settings with the factory default
values.
Move
Enter
Auto Adjustment in Progress
Please wait.
Image Reset is completed.
Return
English - 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Home Theatre PC
You can view higher quality pictures by configuring the screen
settings in PC Mode.
If you set the Home Theatre PC function to On, you can
configure the Detailed Settings (when Picture Mode is set to
Standard or Movie) as in PC Mode.
T V
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
: English
: Off
: Off
: Off
PC
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Home Theatre PC : Off
Light Effect
: Off
More
Move
Enter
Return
3
Press the ▲ or ▼ button to select Home Theatre PC, then
press the ENTER/OK button.
4
5
Select Off or On by pressing the ▲ or ▼ button, then press the ENTER/OK button.
Press the EXIT button to exit.
This function is available only in PC mode.
➢
English - 34
Download from Www.Somanuals.com. All Manuals Search And Download.
Previewing the DTV Menu System
The company does not guarantee the normal operation
➢
of the DTV menu for countries other than the 6 supported
countries (England, Germany, France, Italy, Spain, Austria)
because only these country standards are supported. In
addition, when the country of the broadcast stream differs
from the country selected by the current user, the string
appearing in the channel banner, Info, Guide, Channel List,
etc. may not be displayed properly.
Guide
Now & Next Guide
Full Guide
Available in DTV mode. Preset to the DTV mode by using
the TV/DTV button on your remote control.
To help you navigate around the on-screen menu system
and adjust the various settings available, refer to the
following illustration.
Scheduled List
Default Guide
: Full Guide
Move
Enter
Channel
Exit
Press the D.MENU button to display the menu.
Guide
Auto Store
Now & Next Guide
Full Guide
Scheduled List
Manual Store
Edit Favourite Channels
Channel List
Default Guide
Now/Next
Full Guide
Move
Enter
Setup
Exit
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Menu Transparency : Medium
Parental Lock
All
Favourites
Default
Subtitle
: On
Subtitle Mode
Audio Format
: Normal
: PCM
Setup
Move
Enter
Exit
Menu Transparency
High
Medium
Low
Opaque
Parental Rating
Change PIN
Off
Parental Lock
Subtitle
On
Subtitle Mode
Audio Format
Digital Text
Normal
Hard of hearing
PCM
Dolby Digital
Disable
Enable
Time Zone
System
Product Information
Signal Information
Software Upgrade
Common Interface
Reset
Continued...
English - 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
Audio Language
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Subtitle Language
Teletext Language
Preference
Primary Audio Language
Secondary Audio Language
Primary Subtitle Language
Secondary Subtitle Language
Primary Teletext Language
Secondary Teletext Language
Move
Enter
Exit
The sub-items of the CI Menu may vary depending on the CAM model. (refer to page 46)
➢
Displaying Programme Information
While viewing a channel, additional information about the
current programme may be displayed.
21:49 Sat 1 May
All Channels
1 AFDO, 16:9
AFDO, 16:9
No Block
SD
While viewing a programme, press the INFO button.
The programme information is displayed.
14:20 - 14:33
Contains video with AFD O; coded frame
is 16:9
The information is displayed:
− Parental Rating
➢
Stereo
Subtitle
English
− Video Type: SD, HD, Radio
− Audio Type: Mono, Stereo, Dual, Dolby Digital
− Existence of Teletext or DVB Subtitle
− Audio Language
Exit
To exit from banner information, press the INFO button.
➢
English - 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the DTV Menu
Viewing the DTV Menu
After installing your antenna system and TV with appropriate connectors.
Plug in the AC main power and switch on the TV.
Press the D.MENU button to bring up the DTV menu.
The main menu appears on the screen. Its left side has four icons: Guide, Channel, Setup, and
Language.
Channel
1. Channel
This menu consists of 4 sub-menus:
Auto Store
Auto Store, Manual Store, Edit Favourite Channels, and
Channel Manger.
Manual Store
Edit Favourite Channels
Channel List
Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button. The Channel menu is displayed.
Move
Enter
Exit
Channel
1.1 Auto Store
You can update the channel list when the broadcaster adds new
services or if you move the TV to a new location.
Auto Store
Manual Store
Press the ENTER/OK button to select Auto Store. Press
the ENTER/OK button again to start the search. When
it has finished, the number of scanned services will be
displayed.
Edit Favourite Channels
Channel List
− The existing favourite channel list will not be deleted
when the channel list is updated.
− To stop the scan before it has finished, press the
ENTER/OK button with Stop selected.
Move
Enter
Return
Auto Store
If the signal status is poor, No service found! Check the
aerial connection. message is displayed.
➢
0%
Services found: 0
Start
Channel:
-
Return
Channel
1.2 Manual Store
You can specify the channel for a fast channel search.
Auto Store
− Channel
Manual Store
Press the ▲, ▼ or numeric buttons (0~9) to select a
channel.
Edit Favourite Channels
Channel List
The available channels are 21~68. The corresponding
frequency for the selected channel is automatically set.
− Frequency
Move
Enter
Return
You can specify the frequency (KHz) using the
numeric buttons (0~9). If you do not know the exact
frequency, follow the above step to select the frequency
automatically using channel.
Manual Store
Channel Frequency
Bandwidth
5
177500 KHz 7 MHz
− Bandwidth
Press the ▲ or ▼ button to select a bandwidth. The
available bandwidths are 7 and 8 MHz.
Press the red button to start the scan for digital services.
When it has finished, channels are updated in the channel
list.
Search
Adjust
Return
You can input by pressing the button on the remote control.
You can not change only frequency and when changing a channel the Frequency will be
automatically changed.
➢
➢
Continued...
English - 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel
1.3 Edit Favourite Channels
You can edit your favourite channels using the colour buttons.
Auto Store
In the case of DTV mode, OK or Select can be used as the
ENTER/OK button.
➢
Manual Store
Edit Favourite Channels
Channel List
Press the red button in the Edit Favourite Channels menu
to display all currently stored channels.
Press the ▲ or ▼ button to select a channel you want.
Press the ENTER/OK button. A ““ icon is shown next to
the selected channel and the channel will be added to the
favourites list.
Search
Move
Enter
Return
Edit Favourite Channels
To undo, press the ENTER/OK button again.
➢
Select AlI: Select all channels currently displayed.
Select None: Deselect all selected channels.
Preview: Displays (a) currently selected
channel(s).
If The Favourite Channels settings have been
completed.
2
5
7
BBC TWO
Five
BBC THREE
abc1
15
16
QVC
➢
Select All
Move
Select None
Select
Preview
Return
Add
Edit Favourite Channels
You can use this function when one or more favourite
channels have been selected.
− Press the red button in the Edit Favourite Channels
menu. To add more channels, refer to the previous
section.
2
7
15
BBC TWO
BBC THREE
abc1
− To add all channels to the favourites channel list, press
the red button.
− To remove all channels, press the green button.
− Preview: Displays (a) currently selected channel(s).
− Press the CH LIST button to display the favourite
channel list.
Add
Move
Move
Preview
Return
Delete
Move
− In the Edit Favourite Channels menu, press the ▲ or ▼
button to select the required channel.
− Press the green button. A icon is displayed on the left
side of the channel name.
− Press the ▲ or ▼ button to select the channel that you want to move, then press the green or
ENTER/OK button.
The channel is moved to its new position.
Preview
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
previewed.
− Press the yellow button. Displays currently selected channel.
Delete
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
deleted from the favourite channels list.
− Press the blue button. The selected channel and number will be deleted.
To add a deleted channel back in to the favourite channel list, see Add.
➢
Continued...
English - 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel List
1.4 Channel List
BBC TWO
All Channels-All
806 arte
You can display a list of all channels or your favourite channels.
1. Test Card ‘M’...
2. BBC TWO
3. Vida003b
4. Vida004b
5. Vida005b
6. Vida006b
7. BBC THREE
30. CBBC Channel
40. BBC NEWS24
51. BBCi
800 ARD-MHP-DATA
801 ARD-OnLine-K..
802 BBC ONE
803 MDR FERNSE..
804 NDR FERNSEH..
805 Vida002b
Press the ▲ or ▼ button to select Channel List, then
press the ENTER/OK button.
It can be displayed simply by pressing the CH LIST
button.
➢
Press the yellow button to toggle between your favourite
channels and all channels.
Previous Page
Move
Next Page
Watch
Favourites
TV
Exit
Your favourite channels are only displayed if they were
previously set in the Edit Favourite Channels menu (refer
to page 38).
Press the red or green button to display the previous or
next channel list page.
Press the ▲ or ▼ button to select a channel to be tuned,
then press the ENTER/OK button.
The channel number, name and an icon are displayed in the top left corner while changing
the channel. The channel number and name are displayed if the channel is one of the all
channels, and a icon if the channel is one of the favourite channels.
➢
Press the blue or CH LIST button to exit from the channel list.
Now & Next Guide
2. Guide
This menu consists of 4 sub-menus:
Now & Next Guide, Full Guide, Scheduled List, and Default
Guide.
Now
Next
2.1 Now & Next Guide / Full Guide
The EPG (Electronic Programme Guide) information is provided
by the broadcasters. Programme entries may appear blank or
out of date as a result of the information broadcast on a given
channel.
Watch
Full Guide
Favourites
Exit
The display will dynamically update as soon as new information
becomes available.
− Now & Next Guide
For the six channels indicated in the left-hand column,
displays the Current programme and the Next programme
information.
− Full Guide
Displays the programme information as time ordered
30 minute segments. One and half hours of programme
information is displayed which may be scrolled forwards or
backwards in time.
Press the ▲ or ▼ button to select Now & Next Guide or
Full Guide. Press the ENTER/OK button. The selected
guide menu is displayed.
− Press the red button to toggle between Now & Next
Guide or Full Guide.
− Press the green button to display Favourites or All
Channels list.
− Press the yellow button to scrolls backwards quickly (24
hours).
− Press the blue button to scrolls forwards quickly (24
hours).
You can also display the guide menu simply by
pressing the GUIDE button.
➢
To watch a programme in the EPG list, press the
▲/▼/◄/► button to select a programme of your choice,
then press the ENTER/OK button.
If the next programme is selected, it is scheduled with the clock icon displayed. If the
ENTER/OK button is pressed again, the scheduling is canceled with the clock icon gone.
➢
For details about scheduling programmes, refer to the section.
Continued...
English - 39
Download from Www.Somanuals.com. All Manuals Search And Download.
To view programme information, press the ▲/▼/◄/► button to select a programme of your
choice, then press the INFO button.
Information such as the channel number, programme title and running time, status bar,
➢
and brief summary of the highlighted programme will be displayed in the top right corner
of the screen. If there is a lengthy summary, “…” will be displayed. Press the INFO button
for the full summary text.
Six channels are displayed. To scroll between channels, move to a channel using the ▲
or ▼ button. To display page by page, use the P
or
button.
2.2 Scheduled List
Scheduled List
If you make a scheduled viewing list of programs you may
like to see, the channel will be automatically switched to the
scheduled program at the scheduled time even if you are
watching another program.
Thursday 22 Apr
2 BBC TWO
15:30 ~ 18:00 Once
Animal Park
Thursday 22 Apr
2 BBC TWO
20:00 ~ 21:00 Once
The Hairy Biker’s
Press the red button to add a new programme. The
menu for adding a programme is displayed with Channel
selected.
Add Programme
Edit
Return
Delete
Move
Press the ▲/▼ and ENTER/OK buttons to set the required
channel, time, date, and frequency. When you are satisfied
with your settings, save the adjusted schedule by pressing
the red button.
Scheduled List
Channel
Time
810 Super RTL
10 : 15 to - - : - -
If you want to edit the scheduled programme, select a
programme by pressing the ▲ or ▼ button, then press the
green button. If necessary, select the programme to be
deleted by pressing the ▲ or ▼ button, then press the blue
button.
Date
Thu 03 Mar 2005
Frequency
Save
Cancel
Return
Adjust
Move
When watching analog TV, the reserved DTV channel
➢
cannot be changed. The channel is only changed
automatically to the reserved channel when you are
watching DTV.
Scheduling programme only functions with the
➢
television already turned on, and not from standby
mode. For details about switching the television on and
off automatically, refer to page 10.
2.3 Default Guide
Guide
You can preset the default guide style.
Now & Next Guide
Full Guide
Press the ▲ or ▼ button to select the required option
(Now/Next or Full Guide), then press the ENTER/OK
button. The selected option for default guide is displayed on
the EPG menu and the channel list appears.
Scheduled List
Default Guide
: Full Guide
Move
Enter
Guide
Return
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Now/Next
Full Guide
Move
Enter
Return
Continued...
English - 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide
Now & Next Guide
2.4 All Channels and Favorite Channels
In the EPG menu, you can display all channels or favourite
channels.
Full Guide
Press the green button repeatedly to toggle between the all
and favourite channels list.
Scheduled List
Default Guide
: Full Guide
When the favorite channel list has not been set up:
− The favorite list is empty. Would you like to choose
your favorite now? message is displayed.
− Select Yes. The Edit Favourite Channels menu is
displayed. If you select No, all channels will remain
unchanged.
Move
Enter
Return
Now & Next Guide
− To edit the favourite channels, refer to page 38 for more
details.
Now
Next
All Channels is the list of channels that have been
➢
scanned by the channel list update. All channels
are displayed in the all channel mode.
Favourites (favourite channels) is the list of
channels that has been set in the Edit Favourite
Channels menu (refer to page 38).
Watch
Full Guide
Favourites
Exit
Now & Next Guide
When there is no channel information, the No Data
message will be displayed and you will not be
able to change the channel even if you press the
ENTER/OK button.
The favourites list is empty.
Would you like to choose your
favourites now?
Yes
No
When the No Data message appears and you
cannot change the channel, press the channel
number directly using the numeric buttons.
Watch
Full Guide
Favourites
Exit
3. Language
This menu consists of 4 sub-menus:
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Audio Language, Subtitle Language, Teletext Language,
and Preference.
Move
Enter
Return
3.1 Audio Language / Subtitle Language / Teletext Language
You can change the default value for subtitle, audio and teletext languages.
Press the ▲ or ▼ button to select required menu (Audio Language, Subtitle Language, or
Teletext Language), then press the ENTER/OK button. The options of the selected menu are
displayed.
Continued...
English - 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
Audio Language
3.2 Preference
This menu consists of 6 sub-menus:
Primary Audio Language, Secondary Audio Language,
Primary Subtitle Language, Secondary Subtitle Language,
Primary Teletext Language, and Secondary Teletext
Language.
Subtitle Language
Teletext Language
Preference
Using this feature, users can select one of the languages
(English, German, Italian, Swedish, French, Welsh, Gaelic,
Irish, Danish, Finnish, Norwegian, Spanish, Czech, and Greek).
The language selected here is the default when the user selects
a channel.
Move
Enter
Preference
Primary Audio Language
Return
: German
Press the ▲ or ▼ button to select required menu (Primary
Audio Language, Secondary Audio Language, Primary
Subtitle Language, Secondary Subtitle Language,
Primary Teletext Language, or Secondary Teletext
Language), then press the ENTER/OK button.
Secondary Audio Language : German
Primary Subtitle Language : German
Secondary Subtitle Language : German
Primary Teletext Language : German
The options of the selected menu are displayed.
Press the ▲ or ▼ button to select required option (English,
German, Italian, Swedish, French, Welsh, Gaelic, Irish,
Danish, Finnish, Norwegian, Spanish, Czech, or Greek),
then press the ENTER/OK button.
If you change the language setting, the Audio
Language, Subtitle Language, and the Teletext
Language of the Language menu (refer to page 41)
are automatically changed to the selected language.
The Audio Language, Subtitle Language, and the
Teletext Language of the Language menu show a
Move
Enter
Return
Preference
Primary Audio Language
:
English
German
Secondary Audio Language :
Italian
Primary Subtitle Language :
➢
Swedish
Secondary Subtitle Language : French
Welsh
Primary Teletext Language :
Move
Enter
Return
list of languages supported by the current channel and the selection is highlighted. If you
change this language setting, the new selection is only valid for the current channel. The
changed setting does not change the setting of the Primary Audio Language, Primary
Subtitle Language, or the Primary Teletext Language of the Preference menu.
Continued...
English - 42
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
4. Setup
This menu consists of 9 sub-menus:
Menu Transparency : Medium
Parental Lock
Menu Transparency, Parental Lock, Subtitle, Subtitle Mode,
Digital Text, Time Zone, Audio Format, and System.
4.1 Menu Transparency
Subtitle
: On
Subtitle Mode
Audio Format
: Normal
: PCM
You can set the translucency of the on-screen menu.
Press the ▲ or ▼ button to select required option (High,
Medium, Low, or Opaque), then press the ENTER/OK
button.
Move
Enter
Setup
Return
Menu Transparency : High
Medium
Parental Lock
Low
Subtitle
:
Opaque
Subtitle Mode
Audio Format
: Normal
: PCM
Move
Enter
Setup
Return
4.2 Parental Lock
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by a 4-digit
PIN (Personal Identification Number) code that is defined by
the user.
The on-screen menu will instruct you to assign a PIN code (you
can change it later, if necessary).
Menu Transparency : Medium
Parental Lock
Subtitle
: On
Subtitle Mode
Audio Format
: Normal
: PCM
Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The Parental Lock menu are displayed with
the Parental Rating selected.
Move
Enter
Return
Parental Lock
The default PIN code for a new TV set is 0000.
➢
Enter PIN
If you enter an invalid PIN code, the Invalid PIN
code. Please try again. message is displayed.
Press the ENTER/OK button. Press the ▲ or ▼ button to
select the age rating you want to lock out, then press the
ENTER/OK button.
If you want to change the PIN code, press the ▲ or ▼
button to select Change PIN, then press the ENTER/OK
button.
− Enter your new PIN code by using the numeric buttons
(0~9). The Confirm New PIN is displayed.
.. Enter PIN
Change PIN
Enter New PIN
Return
− Re-enter your new PIN code to confirm by using the
numeric buttons (0~9). The Your PIN code has been
changed successfully message is displayed.
If you forget the PIN code, press the remote control buttons
in the following sequence, which resets the PIN to 0-0-0-0:
POWER (Off) MUTE 8 2 4 POWER (On).
➢
.. Enter PIN
Return
Continued...
English - 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
4.3 Subtitle / Subtitle Mode / Audio Format / Digital Text
You can use various settings to suit your personal preferences.
Menu Transparency : Medium
Parental Lock
Press the ▲ or ▼ button to select required menu (Subtitle,
Subtitle Mode, Digital Text or Audio Format), then press
the ENTER/OK button. The options of the selected menu
are displayed.
Subtitle
: On
Subtitle Mode
Audio Format
: Normal
: PCM
Press the ▲ or ▼ button to select required option, then
press the ENTER/OK button.
Move
Enter
Setup
Return
− Subtitle : On / Off
You can select these options simply by pressing the
➢
SUBTITLE button on the remote control.
Menu Transparency : Medium
Parental Lock
− Subtitle Mode : Normal (basic subtitle) / Hard of hearing
(subtitle for a hearing-impaired person)
Subtitle
: Off
If the programme you are watching does not support
On
Subtitle Mode
Audio Format
: al
➢
the Hard of hearing function, Normal automatically
activates even though Hard of hearing mode is
selected.
: PCM
Move
Enter
Setup
Return
− Audio Format
You can only hear Dolby Digital sound through the audio
receiver connected through an optical cable. You can only
hear PCM sound through the main speaker.
When sound is emitted from both the main speaker and the
audio receiver, a sound echo may occur due to the decoding
speed difference between the main speaker and the audio
receiver. In this case, use the internal mute function.
Menu Transparency : Medium
Parental Lock
Subtitle
: On
Subtitle Mode
Audio Format
: Normal
: PCM
Even if you have selected PCM or Dolby Digital in Audio
➢
Move
Enter
Return
Format, when the input signals are any format of PCM
and Dolby Digital, the input format is applied regardless
of the setting. If the input signals are not any of those,
the setting is not applied.
− Digital Text : Enable / Disable (UK only)
If the programme is broadcast with digital text, this
feature is enabled.
➢
MHEG (Multimedia and Hypermedia Information Coding Experts Group)?
➢
An International standard for data encoding systems used in multimedia and hypermedia. This
is at a higher level than the MPEG system which includes data-linking hypermedia such as
still images, character service, animation, graphic and video files as well as multimedia data.
MHEG is user runtime interaction technology and is being applied to various fields including
VOD (Video-On-Demand), ITV (Interactive TV), EC (Electronic Commerce), tele-education,
tele-conferencing, digital libraries and network games.
4.4 Time Zone (Spain only)
Setup
You can select the time zone where you are located.
This menu is only enabled when you select a country
supported by the time zone.
Digital Text
Time Zone
System
➢
Move
Enter
Return
Continued...
English - 44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
4.5 System
This menu consists of 5 sub-menus:
Digital Text
Time Zone
System
Product Information, Signal Information, Software Upgrade,
Common Interface, and Reset.
− Product Information
You can view your product information. For service or repair,
please contact a Samsung approved dealer.
Press the ENTER/OK button with Product Information
selected. The product information menu is displayed.
− Software Version / Firmware Version
Move
Enter
Return
System
− Signal Information
You can get information about the signal status.
Product Information
Signal Information
Software Upgrade
Common Interface
Reset
Press the ENTER/OK button with Signal Information
selected. The technical information for signal status is
displayed.
− Service / Service ID / Multiplex / Network / Bit error
level / Signal Strength
Move
Enter
Return
− Software Upgrade (Option)
Product Information
To keep your product up-to-date with new digital television
features then software upgrades are periodically broadcast
as part of the normal television signal. It will automatically
detect these signals and display the software upgrade
banner. You are given the option to install the upgrade.
Software Version: T_BDXPDEU00_0710
Firmware Version: T_STDEU7_102c
Software Inforamtion
Press the ENTER/OK button, then the current software
version is shown. To display the software version
information, press the ENTER/OK button again.
Manual Upgrade
Press the ENTER/OK button to search for new software
from the currently broadcasting channels.
Standby Mode Upgrade : On / Off
Return
Signal Information
Service: ?
Service ID: 0000
Multiplex: ? (TSID 0000,ONID 0000)
Network: ? (ID 0000)
Press the ENTER/OK button. To continue software
upgrade with master power on, Select On by pressing
the ▲ or ▼ button.
Bit error level:
10
0
Signal Strength:
45 minutes after entering standby mode, a manual
upgrade is automatically conducted. Since the power
of the unit is turned on internally, the screen may be
on slightly for the PDP product. This phenomenon may
continue for more than 1 hour until the software upgrade
is completed.
Return
Software Upgrade
Software Information
Manual Upgrade
Standby Mode Upgrade : On
Move
Enter
Return
Continued...
English - 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Info.
− Common Interface
Installing the CI Card
a. Purchase the CI CAM module by visiting your nearest
dealer or by phone.
Type: CA
Manufacturer: Canal Plus
Info: Top Up TV
b. Insert the CI CARD into the CAM in the direction of
the arrow until it fits.
c. Insert the CAM with the CI CARD installed into the
common interface slot.
Return
Insert the CAM in the direction of the arrow, right
➢
CI Menu
up to the end so that it is parallel with the slot.
d. Check if you can see a picture on a scrambled signal
channel.
You can install the CAM anytime whether the TV
is ON or OFF.
➢
Application Info.
This contains information on CAM inserted in the CI slot
and displays it.
− Press the ENTER/OK button to display the
information for your application.
CI Menu
This helps the user select an item from the CAM-supported
menu.
Move
Enter
Exit
− Press the ENTER/OK button. The options of the selected menu are displayed.
Press the ▲ or ▼ button to select the required option, then press the ENTER/OK button.
Select the CI Menu based on the PC Card menu.
➢
− Reset
Reset
You can reset the values stored to the factory default values.
WARNING: All channel settings and user
preferences will be lost and returned to the
factory defaults. It is recommended that a
reset is performed only when serious
problems are experienced.
The Reset operation deletes all channel information
➢
and user preferences returning all values to their default
factory state.
Press the ENTER/OK button with Reset selected. The
Enter PIN is displayed.
Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The warning message is displayed. All
values will be reset by pressing the coloured buttons
(red, green, yellow, and blue) in turn.
Return
The default PIN of a new TV set is “0-0-0-0”.
When PIN is changed in Child Lock, the PIN for
resetting automatically changes.
➢
➢
When reset is complete, it operates DTV Plug & Play
(DTV Auto Store, Time Zone-depending on the country, Time Setting) and exits from the digital
TV mode without changing to the analog TV mode. (Refer to page 12)
English - 46
Download from Www.Somanuals.com. All Manuals Search And Download.
What is Anynet+? (PS42Q96HD/PS42Q97HD/PS50Q96HD/PS50Q97HD)
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are
connected.
Connecting Anynet+ Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
To directly connect to TV
Connect the [HDMI 1], [HDMI
2] or [HDMI 3] jack on the TV
TV
Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3
and the HDMI OUT jack of the
corresponding Anynet+ device
using the HDMI cable.
HDMI Cable
HDMI Cable
HDMI Cable
To connect to Home Theater
TV
1
Connect the [HDMI 1],
[HDMI 2] or [HDMI 3]
jack on the TV and the
HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
Anynet+ Device 1
Anynet+ Device 2
2
Connect the HDMI IN jack
of the home theater and
the HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
HDMI Cable
HDMI Cable
Home Theater
Anynet+ Device 3
HDMI Cable
Optical Cable
HDMI Cable
Connect only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio
Input on the receiver.
➢
Connect only one receiver.
➢
➢
You can listen to 5.1 channel sound through the home theater’s speakers. Otherwise, you can only
listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of
the home theater and the TV correctly to listen to TV sound through the home theater. However, you
cannot listen to sound from the BD recorder that is sent to the home theater via the TV in 5.1 channel
sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home
theater.
You can connect an Anynet+ device using the HDMI cable. Some HDMI cables may not support
Anynet+ functions.
➢
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
Anynet+ supports up to 8 AV devices in total.
➢
➢
English - 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Anynet+
The following settings are to use Anynet+ functions.
TV
P 1
View TV
Using the Anynet+ Function
Select Device
Record
1
2
Press the Anynet+ button.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ENTER/OK button to select Anynet+ (HDMI-CEC),
then press the ENTER/OK button.
Menu on Device
Device Operation
Receiver
Setup
:Off
Move
Exit
Enter
Setup
3
Press the ▲ or ▼ button to select On, then press the ENTER/
OK button.
Anynet+ (HDMI-CEC)
Auto Turn Off
:
Off
The Anynet+ (HDMI-CEC) function is enabled.
➢
➢
➢
:
On
If you select Off, Anynet+ (HDMI-CEC) is disabled.
When the Anynet+ (HDMI-CEC) function is disabled, all the
Anynet+ related operations are deactivated.
Searching Connections
Move
Enter
Return
Turning an Anynet+ Device Off Automatically when the TV is Turned Off
2
Press the ▲ or ▼ button to select Auto Turn Off, then press
the ENTER/OK button.
Setup
Anynet+ (HDMI-CEC)
: On
3
Press the ▲ or ▼ button to select On, then press the ENTER/
OK button.
Auto Turn Off
Searching Connections
Off
The Auto turn off function is enabled.
➢
On
If you select Off, the Auto turn off function is canceled.
➢
Press the EXIT button to exit.
The Select Device setting of the TV remote control is to be set
to TV to use the Anynet+ function.
Move
Enter
Return
➢
➢
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned
off. However, if the device is recording, it may not be turned off.
Scanning and Switching between Anynet+ Devices
1
2
Press the Anynet+ button.
TV
P 1
Press the ▲ or ▼ button to select Select Device, then press
the ENTER/OK button.
View TV
DVDR1
DVDR2
DVD1
Select Device
Record
3
Press the ▲ or ▼ button to select to a particular device and
press the ENTER/OK button.
It is switched to the selected device.
If you cannot find a device you want, press the ▲ or ▼ button
to select Searching Connections, then press the ENTER/OK
button.
DVD2
Menu on Device
Device Operation
4
Receiver
Setup
:Off
The meassage Configuring Anynet+ connection... is
displayed. When searching devices completes, the connected
devices are listed in the Anynet+ menu.
Move
Return
Enter
Setup
Switching to the selected devices may take up to 2 minutes.
You cannot cancel the operation during the switching
operation.
➢
Anynet+ (HDMI-CEC)
Auto Turn Off
:
:
On
On
The time required to scan for devices is determined by the
number of connected devices.
➢
➢
➢
Searching Connections
When the device scan is complete, the number of found
devices is not displayed.
Move
Enter
Return
Although the TV automatically scans devices when it is turned
on using the POWER button, devices connected when the TV is on or under a specific circumstance
are not displayed in the device list. Therefore select Searching Connections menu to search
devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
Anynet+ function. Make sure to switch to an Anynet+ device by using the Anynet+ button.
➢
Continued...
English - 48
Download from Www.Somanuals.com. All Manuals Search And Download.
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected
to the TV.
Anynet+ Menu
Description
Switches from Anynet+ to TV broadcast mode.
Your TV connects to the corresponding device.
View TV
Select Device
Record
Starts a recording. (This menu works only for a device supporting
recording.)
Menu on Device
Device Operation
Shows the menu of the connected device.
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Shows the play control menu of the connected device.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
Receiver
Setup
Sound is output through the receiver.
You can set the environment for using Anynet+.
TV Remote Control Buttons Available in Anynet+ Mode
Device Type Operating Status
After switching to the
Available Buttons
Numeric buttons
device, when the menu of
the corresponding device is
displayed on the screen.
▲/▼/◄/►/ENTER buttons
Color buttons
EXIT button
Anynet+ Device
◄◄(Backward search)
►►(Forward search)
(Stop)
After switching to the device,
while playing a file
►
(Play/Pause)
After switching to the device,
when you are watching a TV
program
Device with built-in Tuner
CH ▲/▼ button
VOL +/- button
MUTE button
Audio Device
Anyview2
When Receiver is activated
When watching TV
►
(Play/Pause)
The Anynet+ function only works when the remote control is set to TV.
➢
➢
➢
The REC button works only while in the recordable state.
You cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+
devices only using the TV remote control.
The TV remote control may not work under certain conditions. In this case, re-select the Anynet+
device.
➢
The Anynet+ functions don’t operate for the products from other manufacturers.
In Anynet+ mode, the color buttons may not work properly.
The ◄◄, ►► operations may differ depending on the device.
➢
➢
➢
Recording
You can make a recording of a TV program using a recorder.
Press the REC button.
Recording begins. (Only when the Anynet+ enabled recording device is connected.)
The current TV program is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
➢
You can also record the source streams by selecting Record after pressing the Anynet+ button.
Before recording, check whether the antenna jack is properly connected to the recording device.
For the antenna connection to the recording device, refer to its user manual.
➢
➢
English - 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1
Press the Anynet+ button.
TV
P 1
Press the ▲ or ▼ button to select Receiver, then press the
ENTER/OK button.
View TV
2
Press the ◄ or ► button to select to On, then press the
ENTER/OK button.
Now you can listen to sound through the receiver.
Press the EXIT button to exit.
When the receiver is set to On, you can listen to the TV sound
through the 2-channel receiver.
Select Device
Record
Menu on Device
Device Operation
3
➢
Receiver
Setup
:On
If the receiver is exclusively for a home theater only (supporting
audio only), it may not appear in the device list.
Only when you have connected the optical jack of the TV and
the receiver properly, does Receiver work.
➢
➢
Move
Exit
Enter
In case of a content with copyright problem, listening through the receiver may not properly operate.
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
➢
➢
Check Points before Requesting Service
Symptom
Anynet+ does not work.
Solution
■
Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■
■
■
■
Connect only one receiver.
Check if the Anynet+ device power cord is properly connected.
Check the Anynet+ device’s Video/Audio/HDMI cable connections.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■
■
■
■
Check whether the TV remote control is in TV mode.
Check whether it is Anynet+ exclusive remote control.
Anynet+ doesn’t work at a certain condition. (Searching channels)
When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
Check if the Anynet+ Function of Anynet+ device is set on.
Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
menu.
■
■
I want to start Anynet+.
I want to exit Anynet+.
■
Press the TV button on the TV remote control to switch to TV. Then
press the Anynet+ button to show the Anynet+ menu and select a
menu you want.
■
■
Select View TV in Anynet+ menu.
Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■
Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Connecting to Anynet+
device… message appears
on the screen.
■
■
The Anynet+ device does not
play.
The connected device is not
displayed.
You cannot use the play function when Plug & Play is in progress.
■
■
■
Check whether or not the device supports Anynet+ functions.
Check whether or not the HDMI cable is properly connected.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■
■
Search Anynet+ devices again.
You can connect an Anynet+ device using the HDMI cable only.
Some HDMI cables may not support Anynet+ functions.
The TV program cannot be
recorded.
Check whether the antenna jack on the recording device is properly
connected.
The TV sound is not output
through the receiver.
Connect the optical cable between TV and the receiver.
English - 50
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext Feature (depending on the model)
Most television stations provide written information services
via teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can select
various options to suit your requirements by using the remote
control buttons.
For teletext information to be displayed correctly, channel reception
must be stable. Otherwise, information may be missing or some
pages may not be displayed.
☛
1
2
TV/DTV
Exit from the teletext display (depending on the model)
(index)
Used to display the index (contents) page at any time while you are
viewing teletext.
3
(teletext on/mix)
Press to activate teletext mode after selecting the channel providing
the teletext service. Press it twice to overlap the teletext with the
current broadcasting screen.
4
5
(size)
Press to display the double-size letters in the upper half of the
screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
(mode)
Press to select the teletext mode (LIST/FLOF).
If you press it in the LIST mode, it switches into the List save mode.
In the List save mode, you can save teletext page into list using the
(store) button.
6
7
8
9
0
(sub-page)
Used to display the available sub-page.
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(cancel)
Used to display the broadcast when searching for a page.
(reveal)
Used to display the hidden text (answers to quiz games, for example). To display normal screen,
press it again.
!
Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext
page are colour-coded and can be selected by pressing the coloured buttons. Press one of them
corresponding to the required. The page is displayed with other coloured information that can be
selected in the same way.
To display the previous or next page, press the corresponding coloured button.
@
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages which follow on automatically.
To resume, press it again.
#
(store)
Used to store the teletext pages.
You can change teletext pages by pressing the numeric buttons on
the remote control.
➢
Continued...
English - 51
Download from Www.Somanuals.com. All Manuals Search And Download.
The teletext pages are organized according to six categories:
Part
Contents
A
B
C
D
E
F
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
Teletext information is often divided between several pages
displayed in sequence, which can be accessed by:
Entering the page number
Selecting a title in a list
Selecting a coloured heading (FASTEXT system)
➢
➢
Press the TV/DTV button to exit from the teletext display.
English - 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Wall Mount Kit
This installation is to be used when attaching the wall mount to a wall.
When attaching to other building materials, please contact your nearest dealer.
Wall Mount Kit Specifications (VESA)
Product Family
inch
23 ~ 26
32 ~ 40
46 ~ 52
57
VESA Spec. (A B)
Standard Screw (C D)
Quantity
*
*
200 100
M4 L10
4
4
*
*
200 200
M6 L10
*
*
LCD-TV
600 400
*
700 400
M8 L15
*
4
6
*
42 ~ 50
63
600 400
*
PDP-TV
No VESA
M8
1
2
We provide the standard dimensions for wall mount kits as shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
assembly are provided.
3
4
Do not use screws longer than the standard dimension, as they may cause damage to the inside of
the TV set.
Our 63” model does not comply with VESA Specifications. Therefore, you should use our dedicated
wall mount kit for this model.
English - 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in five different modes: TV, VCR,
Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you
to switch between these modes, and control whichever piece of equipment you choose.
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top
Boxes.
➢
Setting Up the Remote to Operate Your VCR
1
2
3
4
Turn off your VCR.
Press the VCR button on your TV’s remote control.
Press the SET button on your TV’s remote control.
Using the number buttons on your remote control, enter three digits
of the VCR code listed on page 56 of this manual for your brand of
VCR. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
Press the POWER button on the remote control. Your VCR should
turn on if your remote is set up correctly.
5
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of VCR. If no
other codes are listed, try each VCR code, 000 through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in VCR mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1
2
3
4
Turn off your cable box.
Press the CABLE button on your TV’s remote control.
Press the SET button on your TV’s remote control.
Using the number buttons on your remote control, enter three digits
of the cable box code listed on page 57 of this manual for your
brand of cable box.
Make sure you enter three digits of the code, even if the first digit is
a “0”. (If more than one code is listed, try the first one.)
Press the POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
5
If your cable box does not turn on after set-up, repeat steps 2, 3
and 4, but try one of the other codes listed for your brand of cable
box. If no other codes are listed, try each code, 000 through 046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in CABLE mode, the volume buttons still
control your TV’s volume.
Continued...
English - 54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Remote to Operate Your DVD
1
2
3
4
Turn off your DVD.
Press the DVD button on your TV’s remote control.
Press the SET button on your TV’s remote control.
Using the number buttons on your remote control, enter three digits
of the DVD code listed on page 58 of this manual for your brand of
DVD. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
Press the POWER button on the remote control.
5
Your DVD should turn on if your remote is set up correctly.
If your DVD does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of DVD. If no
other codes are listed, try each code, 000 through 141.
Note on Using Remote Control Modes: DVD
When your remote control is in DVD mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Set Top Box
1
2
3
4
Turn off your STB.
Press the STB button on your TV’s remote control.
Press the SET button on your TV’s remote control.
Using the number buttons on your remote control, enter three digits
of the STB code listed on page 57 of this manual for your brand of
STB. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
Press the POWER button on the remote control.
5
Your STB should turn on if your remote is set up correctly.
If your STB does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of STB. If no
other codes are listed, try each code, 000 through 074.
Note on Using Remote Control Modes: STB
When your remote control is in STB mode, the volume buttons still
control your TV’s volume.
Continued...
English - 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Codes
VCR
Brand
Code
Brand
Code
SAMSUNG
ADMIRAL
AIWA
000 001 002 003 004 005 077 078 079
020
025
MITSUBISHI
MONTGOMERY WARD 020
MTC
019 034 041 046
002 025
AKAI
004 027 032
007 026
018
022
MULTITECH
NEC
OPTIMUS
PANASONIC
PENTAX
002 005 025 038
007 008 018 026 037 062 064
020
021 056 071 072
019 041 075
AUDIO DYNAMICS
BELL&HOWELL
BROKSONIC
CANDLE
002 003 006 008 015 055
CANON
021 056
PENTEX RESEARCH+ 008
CITIZEN
002 003 006 008 015 055
PHILCO
021 056 059
COLORTYME
CRAIG
CURTIS MATHES
DAEWOO
DB
007
002 024
PHILIPS
021 080
019 026 039 053
015 049 055
017
PIONEER
PORTLAND
PROSCAN
QUARTZ
002 007 008 017 021 025 056 064 066
003 010 011 012 013 014 015 016
007 026
018
DIMENSIA
DYNATECH
ELECTROHOME
EMERSON
017
025
034
QUASAR
RADIO SHACK/
REALISTIC
RCA
021 056
006 018 020 021 024 025 029 034
048 056
002 017 019 021 035 041 043 057
001 003 006 021 022 025 030 032 034
040 047 050 052 060 063 065 066 067
068 076
069 073
SANSUI
026
FISHER
018 024 028 029 048 051 061
SANYO
018 024
FUNAI
025
SCOTT
003 047 052 067
GENERAL ELECTRIC
GO VIDEO
002 005 017 021 056
002
SEARS
SHARP
006 018 019 024 028 029 041 048 051
020 034 045 015
LG(Goldstar)
HARMAN KARDON
HITACHI
006 007 008 009 010
007
019 025 041 042 074
SHIMTOM
SIGNATURE
SONY
027 033 038 058
025
027 033 044
INSTANT REPLAY
JC PENNEY
021
SYLVANIA
SYMPHONIC
TANDY
021 025 056 059
025
018 025
002 007 018 019 021 026 037 041
054 056
JCL
KENWOOD
KLH
007 008 018 021 026 037
007 008 018 026 037
070
TASHIKA
TATUNG
TEAC
006
037
025 037 068
LIOYD
LOGIK
LXI
025
038
025
TECHNICS
TEKNIKA
TMK
021
006 021 025 031
066
JVC
081 082 083
021 056 059
007 008 018 021 026 037 062
006
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
003 019 029 051 052
002 006
002
007 026
026
007 026
002
MAGNAVOX
MARANTZ
MARTA
KONIA
ORION
MEI
036
073 074 075 076
021
006 021 024 025
034
MEMOREX
MGA
002 003 006 019 020 021 024 025 034
038 041
MIDLAND
MINOLTA
005
019 041 075
YAMAHA
ZENITH
007 008 018 026 037
023 027 033
Continued...
English - 56
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE BOX
Brand
Code
Brand
Code
SAMSUNG
GI
000 001 002 003 004 005 006 007
041
REGENCY
SA
015 023
042 043
HAMLIN
HITACHI
JERROLD
MACOM
MAGNAVOX
OAK
003 024 031
025 030
038 039
025 030
019 023 028
026
SCIENTIFIC ATLAN
SPRUCER
STARGATE 2000
SYLVANIA
TEXSCAN
TOCOM
042 043
022
036
016
016
032
PANASONIC
PHILIPS
PIONEER
RCA
003 022 027 037 044
019 021 023 028
004 018 020 044
014 022 040
003
UNIVERSAL
VIEWSTAR
WARNER AMEX
ZENITH
033 034
019 021 023 028
046
017 029 035 037 045
REGAL
SAMSUNG SET-TOP BOX
Product
Ground wave STB
Satellite STB
CABLE STB
STB DVD COMBO
Satellite STB HDD COMBO Standard
Code
001 002
003
004
008
Product
Code
010
011
012
013
014
Satellite STB HDD COMBO Premium
CABLE STB HDD COMBO Standard
CABLE STB HDD COMBO Premium
Ground wave STB HDD COMBO Standard
Ground wave STB HDD COMBO Premium
009
SET-TOP BOX
Brand
ALPHASTAR
ANAM
CHANNEL MASTER
CROSSDIGITAL
CHAPARRAL
DIRECT TV
Code
023
043
018 034
019
035
015 016 017 019 022 045 060
061 062 065 066 067 068
074
Brand
Code
044 073
LG(Goldstar)
MAGNAVOX
MEMOREX
MOTOROLA
MACOM
MITSUBISHI
NEXT LEVEL
PHILIPS
016 021 036 038 039 040 041 042
016
064
018
015
047 048 064
015 016 017 021 033 036 038 039
DAEWOO
DISH NETWORK SYSTEM 069 070
040 041 042 067
DISHPRO
DRAKE
DX ANTENNA
ECHOSTAR
EXPRESSVU
GOI
069
018 024 032
027
025 069 070 071
069
069
065
046 047 048 063 064
069
056
022
015 017
020
020
059
063
PRIMESTAR
PANASONIC
PAYSAT
PROSCAN
RCA
RADIOSHACK
REALISTIC
STS
STAR TRAK
SKY
SKY LIFE
SHACK
STAR CHOICE
SONY
TOSHIBA
ULTIMATE TV
UNIDEN
046 049 050 063
058 059 061 062
016
065 066
051 052 053 065 066
064
057
020 027
026
031
005 006 007
064
064
054 060
015 017 028 029 030 072
060 066
016 021 037 055 056 057
024 031 068
GE
GENERAL INSTRUMENT
HTS
HOME CABLE
HITACHI
HUGHES NETWORK
IQ
IQ PRISM
JANEIL
JERROID
JVC
069 070
ZENITH
Continued...
English - 57
Download from Www.Somanuals.com. All Manuals Search And Download.
SAMSUNG DVD
Product
DVD
DVDR
BD Record
VCR COMBO
VCR Record
DHR COMBO
Code
000 001 002
003 004
005 006
007 008 009 010 011
012
Product
Code
014 015 016
017
018
019
Home Theater VCR COMBO
HDD Record COMBO
TWIN TRAY COMBO
STB DVD COMBO
DVD Receiver
020
021
013
AV Receiver
DVD
Brand
ANAM
AUDIOVOX
AUDIOLOGIC
ANABA
Code
030
075
085
072
Brand
Code
048 049 050
052
053
144
074
NORCENT
NEXT BASE
NEC
NANTAUS
NESA
APEX DIGITAL
070 071 074 086 083 084 088
111 112
114
062
OPTOMEDIA ELECTRONICS
OPTIVIEW
ONKYO
105
072
076 092 119
AIWA
BROKSONIC
BLAUPUNKT
B&K
CURTIS MATHES
CYBER HOME
CLARION
CIRRUS
074
122 123
027
065 077 078 079 082
080 125
081
PHILCO
044 045
046 047
023
024 034 124 134 136 137 138
036 076
117 118
PRINCETON
PROSCAN
PANASONIC
PHILIPS
ROTEL
CINEVISION
DAEWOO
DENON
095
066
146
RIO
RCA
RAITE
120
023 035 074 075 131 132
073
FARENHEIT
FISHER
067 068
090
ROWA
SAMPO
038
104
GPX
060
SONY
026 029 126 127 128 129
GO VIDEO
GE
GREENHILL
HITACHI
HITEKER
HOYO
061 089 133 135
069 074
074
064 113
071
130 141
039 041
042
043 093
140
SHERWOOD
SVA
SYLVANIA
SHARP
073
SANSUI
062
HARMAN / KARDON
IRT
INTEGRA
JBL
JVC
JATON
091 110
089
092
SANYO
SHINSONIC
SANYO
THOMSON
TOSHIBA
TECHNICS
TVIEW
062
094
090
145
028 062 076
139
072
091
022 033 115 116
073
051 108 109
073
KENWOOD
KISS
TOKAI
073
KONKA
KLH
059 100 106 107
074 075
025 031
057
058
054
055
056
076 093
074 094
073
TEAC
TECHWOOD
TREDEX
URBAN CONCEPTS
VENTURER
VOCOPRO
YAMAHA
YAMAKAWA
XWAVE
096
097
098 099 101
076
075
LG(Goldstar)
LOEWE
LASONIC
MOBILE AUTHORITY
MEMOREX
MALATA
MAGNAVOX
MINTEK
MONYKA
102
032 063
040 073
103
ZENITH
076 121
English - 58
Download from Www.Somanuals.com. All Manuals Search And Download.
How to assemble the Stand-Base (depending on the model)
Using the 6 screws for securing the stand base and the
monitor, firmly attach the monitor to the stand base.
(The exterior of the set may be different than the picture.)
In case of installing your TV on the wall,
close the cover (1) on the stand-base
connection part using two screws for
hiding.
Warning
Firmly secure the stand to the TV
before moving it, as the stand may
fall and could cause serious injury.
Two or more people should carry
➢
the TV. Never lay the TV on the
floor because of possible damage
to the screen.
Always store the TV upright.
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the television and contact your local dealer.
No sound or picture
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the
button on the remote control.
(Power) button (On/Off) on the front panel or press the POWER
Check the picture contrast and brightness settings.
Check the volume.
Check if Internal Mute is set to ON.
Normal picture but no sound
Check the volume.
Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
Adjust the colour settings.
Check that the broadcast system selected is correct.
Sound and picture interference
Try to identify the electrical appliance that is affecting the television, then move it further away.
Plug the television into a different main socket.
Blurred or snowy picture, distorted sound
Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check that the “+” and “–” ends of the batteries are inserted correctly.
Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
On your computer check; Power, Signal Cable.
The TV is using its power management system.
Move the computer’s mouse or press any key on the keyboard.
On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
The TV is using its power management system.
Press the Source button on the panel or remote control.
Turn the TV off and on.
English - 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and
are subject to modification without notice.
PS42Q96HD/PS42Q97HD
PS42C9HD/PS42C96HD
PS50Q96HD/PS50Q97HD
PS50C9HD/PS50C96HD
Model Name
Screen Size (Diagonal)
PC Resolution
42 inch
50 inch
1024 x 768 @ 60 Hz
1360 x 768 @ 60 Hz
Sound (Output)
10 W + 10 W
10 W + 10 W
15 W + 15 W
10 W + 10 W
Dimension (WxHxD)
Body
1055 x 700 x 104 mm
1055 x 700 x 95 mm
1055 x 757 x 316 mm
1055 x 759 x 316 mm
1231 x 789 x 104 mm
1231 x 789 x 95 mm
1231 x 849 x 316 mm
1231 x 849 x 316 mm
With stand
Weight
Body
31 kg
31 kg
34 kg
34 kg
42 kg
41 kg
44 kg
44 kg
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
This device is a Class B digital apparatus.
Design and specifications are subject to change without prior notice.
➢
For the power supply, refer to the label attached to the product.
English - 60
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally
left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally
left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care centre.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez
contacter le Service Consommateurs Samsung.
Kontakt zu Samsung
Falls Sie Fragen oder Anregungen zu Samsung-Produkten haben, wenden Sie sich bitte an den
Samsung-Kundendienst.
Contatta SAMSUNG WORLD-WIDE
Se avete commenti o domande sui prodotti Samsung, contattate il Servizio Clienti Samsung.
Contact Samsung wereldwijd
Wanneer u suggesties of vragen heeft met betrekking tot Samsung producten, gelieve contact op te
nemen met de consumenten dienst van Samsung.
Contacte SAMSUNG GLOBAL
Se tem algumas dúvidas ou comentários sobre os produtos Samsung, contacte por favor a nossa
linha de apoio a clientes Samsung.
Obrnite se na SAMSUNG WORLD WIDE (GLOBALNI SAMSUNG)
V primeru vprašanj ali pripomb v zvezi z izdelki Samsung se obrnite na center za pomoč strankam
SAMSUNG.
Contacte con SAMSUNG WORLD-WIDE
Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con
nuestro Servicio de Atención al Cliente.
Download from Www.Somanuals.com. All Manuals Search And Download.
Country
Web Site
Customer Care Centre
02 201 2418
BELGIUM
CZECH REPUBLIC
DENMARK
ESTONIA
844 000 844
70 70 19 70
800-7267
FINLAND
030-6227 515
FRANCE
GERMANY
HUNGARY
ITALIA
01805-121213 (€ 0,14/Min)
06-80-SAMSUNG (7267864)
800 SAMSUNG (7267864)
8 800 080 11 88
KAZAKHSTAN
LATVIA
800-7267
LITHUANIA
LUXEMBURG
NETHERLANDS
NORWAY
8-800-77777
0032 (0)2 201 24 18
0900 20 200 88 (€ 0,10/Min)
815-56 480
POLAND
0 801 801 881
PORTUGAL
REPUBLIC OF IRELAND
RUSSIA
80 8 200 128
0818 717 100
8-800-200-0400
SLOVAKIA
SPAIN
0800-SAMSUNG (7267864)
902 10 11 30
SWEDEN
0771-400 200
SWITZERLAND
U.K
0800-7267864
0870 SAMSUNG (7267864)
8-800-502-0000
UKRAINE
UZBEKISTAN
140-1234
Download from Www.Somanuals.com. All Manuals Search And Download.
|