Step 4 : Connect External Devices
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
For the very best picture quality, select HD signal sources and use HDMI cables and connections.
Note that many digital cable programs are not in HD. Check with your video provider to ensure your
are receiving HD signals.
Connecting an audio device
Connect your TV to your Home Theater or other audio
device to enjoy enhanced sound quality.
1-800-SAMSUNG (1-800-726-7864)
Analog Audio connection
HD connection (up to 1080p)
STOP
If you have problems operating your
TV, call:
Samsung Electronics America, Inc.
Using an Audio Cable
Using an HDMI Cable
Please do not return this unit.
85 Challenger Road Ridgefield Park, NJ 07660-2112
HDMI OUT
Device
Device
AUDIO IN
Samsung Electronics Canada Inc.
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
The HDMI connection carries
digital video and audio.
Amplifier / DVD Home Theater
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
Best Connection
Digital Audio connection
Using an Optical Cable
HD connection (up to 1080p)
Getting Started
Digital Audio System
Using an DVI to HDMI Cable
OPTICAL
AUDIO OUT
Device
Step 1 : Install the Stand
Follow the steps below to connect the TV to the stand.
DVD / Blu-Ray player /
DVI OUT
Cable Box /
Satellite receiver (STB)
Make sure to distinguish between the front and back of the Stand and Guide
Connecting a PC
✎
Stand when assembling them.
Connect your TV to a PC to use it as a Monitor.
HD connection
Make sure that at least two people lift and move the LCD TV.
✎
✎
Very Good Connection
Lay the product down, with the screen facing up and fasten the screws.
Using an D-Sub Cable
Component connection (up to 1080p)
PC OUT
AUDIO OUT
Using a Component Cable
1
AUDIO OUT
COMPONENT OUT
Device
PC
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Audio/Video connection (480i only)
Good Connection
Using an Audio/Video Cable
Using an HDMI Cable
VIDEO OUT
VCR
AUDIO OUT
AUDIO OUT
DVI OUT
2
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
PC
Lowest Quality Connection
Stand
After the time zone screen,
The connection method
for best HD screen quality
is displayed. Press Right
arrow button on your
remote to view each screen
in succession. Press the
MEnU button to skip this
section.
Step 5 : Run Plug & Play
Plug & Play
Plug & Play
When you turn on your TV for the first time, it automatically launches
the Plug & Play function. With Plug & Play, you can select the On
Screen Display language, set the clock mode, and launch the TV’s
channel memorizing process. It also displays connection instructions
similar to those in this guide.
Auto Program in Progress.
Select the Antenna source to memorise.
DTV Cable : --
Cable : --
Stop
Cable 28
15%
Air
Start
5
8
9
3
Cable
Auto
Start
Start
Screw
To navigate while Plug & Play is running, press the Up, Down, Left or
Right arrow buttons on your remote. To make a selection, press the
EnTErE button. To skip a screen, press the MEnU button.
E
Enter m Skip
U
Move
E
Enter m Skip
Step 2 : Install the Batteries into the Remote
The TV memorizes the available channels. This process can take
up to 45 minutes.
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your
TV is attached to an antenna and cable with no box, select Auto.
When done, press EnTErE button on your remote. The Select
Cable System screen appears.
To install batteries into your remote control, follow these steps:
To turn on your TV, press the POwEr button on the remote or press
the POwEr button on the TV. To run Plug & Play, follow these steps:
1. Lift the cover on the back of the remote upward
Plug & Play
The Enjoy your TV screen
appears. Then press
EnTErE button.
as shown in the figure to the right.
Plug & Play
Set the Clock Mode.
Auto
2. Install two AAA batteries.
Select Language of the OSD.
English
IMPORTANT: If your TV is attached to a cable or satellite box,
skip Steps 3 through 5. After Plug & Play is complete, set your TV to
Channel 3 or 4, according to the directions for your cable or satellite box.
Make sure to match the + and - ends of
the batteries to the diagram in the battery
compartment.
Clock Mode
Manual
✎
6
Español
1
Language
Français
U
Move
E
Enter m Skip
3. Replace the cover.
Plug & Play
U
Move
E
Enter
After the TV has memorized the channels, choose the Clock
Mode. Select Auto if you have a digital channel in your area. Select
Manual if you don’t, or if you have a cable or satellite box. When
done, press EnTErE button.
Selects the cable system.
On the Language screen, select the language for the On Screen
Display (OSD) using your remote control, and then press
EnTErE button. The Home Use screen appears.
Analog
Digital
STD
STD
HrC
IrC
Step 3 :Connect Power and Antenna or Cable
4
HrC
IrC
If you select Manual, the clock setting screen appears.
Start
✎
Plug & Play
U
Move
E
Enter m Skip
Plug & Play
Select ‘Home Use’ when installing this TV in your home.
Connect AnT In to:
Set to daylight saving time.
Off
If your TV is attached to a cable system and you have no cable box,
you must select your cable system type. If you have Digital cable, you
must select the cable system type for both Analog and Digital.
2
• Wall cable jack or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Store Demo
Home Use
Move
DST
On
7
or
Auto
After you have selected the cable system type, select Start, and then
press the EnTErE button on your remote.
L
E
Enter
U
Move
E
Enter m Skip
Use a 75 ohm (round) cable.
Power Input
Most cable systems are Standard (STD) systems. If you are not
sure about what kind of cable system you have, contact your
cable company.
Select Home Use, and then press EnTErE button. If you select
Store Demo, the TV will reset your picture and audio settings every
30 minutes. After you press EnTErE button , the Antenna Source
screen appears.
✎
Select the daylight savings time setting: Off, On, or Auto, and then
press EnTErE button.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 1
|