Samsung Flat Panel Television 470D User Guide

4 CHANNEL DVR  
User Manual  
SRD-470/470D  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN11 11  
2010-04-30 오후 6:06:2233  
IMPORTANT SAFETY INSTRUCTIONS  
Read these operating instructions carefully before using the unit.  
Follow all the safety instructions listed below.  
Keep these operating instructions handy for future reference.  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings, Install in accordance with the manufacturer’s  
instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has  
two blades with one wider than the other. A grounding type plug has two blades and a third  
grounding prong. The wide blade or the third prong are provided for your safety. if the provided  
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury from  
tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long  
periods of time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has  
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been  
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
English _3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN33 33  
2010-04-30 오후 6:06:3399  
overview  
BEFORE START  
This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection  
to other equipment, menu setup, etc.  
You have to keep in mind the following notices :  
SAMSUNG retains the copyright on this manual.  
This manual cannot be copied without SAMSUNG’s prior written approval.  
We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of  
instructions mentioned in this manual.  
Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be  
removed from the unit.  
Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this  
DVR, check the compatibility. Consult your provider for the compatibility list.  
Warning  
Battery  
It is essential that when changing the battery in the unit, the replacement battery must be of the same type  
otherwise there may be a possibility of an explosion.  
The following are the specifications of the battery you are using now.  
Normal voltage : 3V  
CALIFORNIA USA ONLY  
Normal capacity : 170mAh  
Continuous standard load : 0.2mA  
This Perchlorate warning applies only to primary CR (Manganese Dioxide)  
Lithium coin cells in the product sold or distributed ONLY in California USA.  
“Perchlorate Material - special handling may apply,  
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”  
Operating temperature : -20°C ~ +85°C  
(-4°F ~ +185°F)  
Connect the power cord into a grounded outlet.  
J
The Mains plug is used as a disconnect device and shall stay readily operable at any time.  
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.  
System Shutdown  
Turning off the power while the product is in operation, or undertaking improper actions may cause damage  
or malfunction to the hard drive or the product.  
Please turn off the power using the Power button on the front of your DVR.  
After selecting <OK> in the pop-up menu, you can pull off the power cord.  
You may want to install a UPS system for safe operation in order to prevent damage caused by an  
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)  
Operating Temperature  
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).  
This product may not work properly if you run right after a long period of storage at a temperature below the  
guaranteed one.  
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand  
at room temperature for a period.  
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).  
Likewise, the hard drive may not work at a temperature below the guaranteed one.  
Ethernet Port  
This equipment is in door use and all the communication wirings are limited to inside of the building.  
4_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN44 44  
2010-04-30 오후 6:06:4400  
CONTENTS  
4
7
9
Before Start  
OVERV4IEW  
Features  
Part Names and Functions (Rear)  
10 Part Names and Functions (Front)  
12 Remote Control  
13 Checking the installation environment  
INSTALLATION  
14 HDD Addition  
13  
17 Connecting the Video, Audio, and Monitor  
17 Connecting the USB  
CONNECTING WITH OTHER1DEV7ICE  
17 Connecting POS Device  
18 Connecting the Alarm Input/Output  
18 Connecting the RS485 Device  
19 Connecting the Network  
21 Getting Started  
23 Live Screen Configuration  
27 Live Mode  
2L1IVE  
29 Spot Out  
29 Zoom  
30 Audio ON/OFF  
30 Freeze  
30 Event Monitoring  
32 System Setup  
USING THE DVR  
42 Setting the Device  
50 Setting the Recording  
53 Setting the Event  
56 Backup  
32  
57 Network Configuration  
64 Controlling a PTZ device  
English _5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN55 55  
2010-04-30 오후 6:06:4400  
overview  
66 Search  
SEARCH & PLAY  
69 Playback  
66  
70 Introducing Web Viewer  
71 Connecting Web Viewer  
73 Using Live Viewer  
79 Using Search Viewer  
83 Viewer Setup  
WEB7VIEW0ER  
93 About  
94 SEC Backup Viewer  
BACKUP9VIEW4ER  
96 Product Specification  
99 Product Overview  
100 Default Setting  
APPENDIX  
103 Troubleshooting  
96  
6_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN66 66  
2010-04-30 오후 6:06:4411  
FEATURES  
The SRD DVR (Digital Video Recorder) employs H.264 video encoding for 4 channel inputs and G.723 audio  
encoding for 4 channels while simultaneously supports hard disc recording and playback.  
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video  
and audio data.  
4 CH Composite Input Connectors  
CIF(S)/2CIF(M)/4CIF(L) Recording  
Network transfer regardless of the recording conditions using network specific codec  
Improved quality using de-interlace chip  
HDD information and status with HDD SMART  
Record at 4CIF Size (NTSC: 704*480, PAL: 704*576) 120(NTSC)/100(PAL)IPS  
4 CH Loop Through video port  
HDD Overwrite  
Massive HDD backup via USB 2.0  
Backup using USB 2.0 memory and/or external CD/DVD writer  
(DVD writer not supported in SRD-470)  
Record and play 4 CH video data simultaneously  
Various search modes (time, event, backup, POS, motion detection)  
Lots of storage modes (time lapse, event, timed recording)  
HDD extension (USB 2.0)  
Alarm connection (input: 4, output:2, reset: 1)  
Remote monitoring via Windows Network Viewer  
English _7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN77 77  
2010-04-30 오후 6:06:4411  
overview  
Standards Approvals  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15  
M
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment  
in a residential area is likely to cause harmful interference in which case the user will be required to correct the  
interference at his own expense.  
Package Contents  
Please unwrap the product, and place the product on a flat place or in the place to be installed.  
Please check the following contents are included in addition to the main unit.  
Remote Control  
Adaptor  
Power Cable  
Network Viewer Software /  
User Manual CD  
User Manual  
Remote Control Battery (AAA)  
HDD Fixing Screw  
SATA Cable  
(Only applicable for SRD-470 : 4EA)  
(Only applicable for SRD-470 : 1EA)  
For models that are not equipped with the HDD, one SATA cable is provided for HDD installation.  
M
8_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN88 88  
2010-04-30 오후 6:06:4422  
PART NAMES AND FUNCTIONS (REAR)  
1
2
3
4
5
11  
10  
9
8
7
6
Part Names  
Functions  
VGA  
Output port for VGA video signal.  
RS-232C communications port.  
RS-232C  
VIDEO OUT  
BNC type of output port for the composite video signal.  
Output port (RCA jack) for the audio signal.  
AUDIO OUT  
It is recommended to use an amplifier-integrated speaker for the output of the audio  
signal.  
AUDIO IN 1~4  
NETWORK  
Output ports (RCA jacks) for the audio signal.  
Network connection port.  
DC 12V  
Port to be connected to the 12V power source.  
1~4, G : Alarm input ports.  
ALARM IN  
ALARM OUT  
RS485  
1, 2, COM : Alarm output ports.  
Used to establish RS485 communications. (TX+, TX-)  
USB connection port.  
USB  
SPOT  
BNC type of output port for the Spot signal.  
Port to transfer the video signal to other video devices.  
THROUGH  
Input port for the composite video signal.  
VIDEO IN  
Supports both NTSC and PAL video signal.  
English _9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN99 99  
2010-04-30 오후 6:06:4444  
overview  
PART NAMES AND FUNCTIONS (FRONT)  
SRD-470  
1
2
3
5
SRD-470  
9
8
7
3
6
SRD-470D  
1
2
4
5
SRD-470D  
9
8
7
6
10_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1100 1100  
2010-04-30 오후 6:06:4455  
Part Names  
Power  
Functions  
Power LED : Displays the power ON/OFF status.  
Power Button : Used to turn the DVR ON/OFF.  
In Live mode, pressing it will switch the mode to 4-split, PIP, and Auto Sequence in sequence.  
In Search mode, pressing it will switch the mode to 9-split and 4-split in sequence.  
For the Play Screen mode, refer to “Play”. (page 69)  
MODE  
AUDIO  
ALARM  
REC  
Sets Audio ON/OFF.  
Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the  
icon.  
Starts or ends the recording.  
Step Rewind () : Used for backward frame-by-frame search while in PAUSE.  
Fast Rewind () : Used for quick backward search while in Play.  
(-x2, -x4, -x8, -x16, -x32, -x64)  
/  
Stop : Used to stop the playback.  
Play/Pause : Used to pause or resume the screen.  
/  
/  
Open/Close  
Fast Forward () : Used for quick forward playback. (x2, x4, x8, x16, x32, x64)  
Step Forward ( ) : Used for forward frame-by-frame search while in PAUSE.  
Used to open and close the DVR-RW disc tray. (available for SRD-470D only)  
ALARM : Lights on when an event occurs.  
HDD : Displays the normal access to HDD.  
Upon access to HDD, LED repeats on and off.  
LED Indicator  
NETWORK : Displays both network connection and data transfer status.  
BACKUP : Displays when Backup is in progress.  
REC : Lights on when recording is in progress.  
Direction &  
Used to change a value or move the cursor up/down/left/right (ꢀꢁ◄ ►).  
Select Button  
Selects a menu item or executes the selected menu.  
PTZ : Sets PTZ Mode ON/OFF.  
ZOOM(TELE) : Sets the screen to the x2 digital zoom.  
Runs the TELE function in the PTZ Mode.  
FREEZE(WIDE) : Runs the FREEZE function in the Live Mode.  
Camera Control  
Runs the WIDE function in the PTZ Mode.  
SEARCH(VIEW) : This is the function that switches over to the Search mode.  
(Perform the VIEW function when selecting the PTZ button.)  
MENU : Used to access the Menu screen or move to the previous menu.  
Used to select channel numbers directly in the Live Mode, or numbers in the numeric input  
Channel  
USB Port  
mode.  
Connects the USB devices.  
English _11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1111 1111  
2010-04-30 오후 6:06:4466  
overview  
REMOTE CONTROL  
BACKUP  
SEARCH  
Displays the search menu.  
Displays the Backup Menu.  
OPEN/CLOSE  
Opens or closes the CD tray.  
MODE  
Changes the screen mode.  
DVR  
Activates the DVR function.  
POWER  
Displays the Exit pop up screen.  
+
NUMBER [0~ 10]  
Used as the numeric input keys, or displays a single  
channel.  
ID  
Sets the ID of the system.  
Select 2 digits from 0 ~ 9 while pressing the ID Key.  
Skip Backward (by unit time),  
Slow Rewind, Slow Forward,  
Skip Forward (by unit time)  
Move Frame  
While paused, moves to the previous/next frame.  
FR, STOP, PLAY/PAUSE, FF  
T/W  
PTZ  
Zooms in or out.  
Displays or ends PTZ.  
SCROLL ,.  
Moves the menu scroll.  
MENU  
RETURN  
Goes to the system menu screen.  
Returns to the previous screen.  
Up/Down/Left/Right(▲▼◄ ►)/ENTER  
Moves the cursor up/down/left/right, and runs the  
Select Menu.  
AUDIO  
Turns Audio on/off.  
FREEZE  
ALARM  
Freezes the screen temporarily.  
Cancels the Alarm.  
ZOOM  
Runs the digital zoom (x2) function.  
REC LOCK  
REC  
Selects the recording lock function.  
Starts or ends the live recording.  
PRESET  
VIEW  
Displays the Preset Setup.  
Runs the View function in the PTZ mode.  
Using the Numeric buttons  
1. Press any button among 1 to 4.  
2. Move to the selected channel number.  
Changing the Remote Control ID  
1. Press the ID button of the remote control and check the ID displayed on the DVR screen.  
The factory default ID of the remote control is 00.  
2. Enter 2 digits of your selection in order, while pressing the system [ID] button.  
3. When ID input is done, press the system [ID] button again to check the setting.  
If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.  
M
Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 46)  
12_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1122 1122  
2010-04-30 오후 6:06:4466  
installation  
Please take note of the followings before using this product.  
Do not use the product outdoor.  
Do not spill water or liquid in the connection part of the product.  
Do not impose the system to excessive shock or force.  
Do not pull out the power plug forcefully.  
Do not disassemble the product on your own.  
Do not exceed the rated input/output range.  
Use a certified power cord only.  
For the product with an input ground, use a grounded power plug.  
CHECKING THE INSTALLATION ENVIRONMENT  
Temperature  
One Year: 24HR X 365 DAY =8,760 HR  
Samsung Digital Video Recorder (“DVR” hereinafter) is a  
Unit: ºC  
state-of-art security device, and contains mass storage hard  
disk(s) and critical circuits inside.  
When the temperature rises inside the product, the product  
may breakdown and the product life be shortened. Please  
pay attention to the following recommendations before  
installation.  
Life (Unit: HOURS)  
[Figure 1]  
The followings are the recommendations when Samsung DVR is installed on a rack.  
1. Please ensure that the rack inside is not sealed.  
2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.  
3. If the DVR or other devices on a rack is to be stacked as in the picture, provide a  
suitable space or install a ventilating opening for air circulation.  
DI  
DI  
DI  
DI  
GI  
T
A
L
V
ID  
ID  
ID  
ID  
EO  
EO  
EO  
EO  
RE  
CO  
RD  
RD  
RD  
RD  
ER  
ER  
ER  
ER  
SR  
D-  
47  
0D  
0D  
0D  
0D  
MO  
DE  
AU  
DIO  
ALA  
AL  
RM  
RM  
RM  
RM  
AR  
1
1
1
1
M
HDD  
NET  
NET  
NET  
NET  
WO  
WO  
WO  
WO  
RK  
RK  
RK  
RK  
2
RE  
BAC  
BAC  
BAC  
BAC  
KUP  
KUP  
KUP  
KUP  
REC  
REC  
REC  
REC  
3
4
ZO  
OM  
FR  
EE  
ZE  
SE  
AR  
CH  
TE  
L
ME  
ME  
ME  
ME  
WID  
NU  
E
VIE  
W
GI  
GI  
GI  
T
A
L
V
RE  
CO  
SR  
D-  
47  
4. For natural air convection, place the inlet at the bottom of the rack and the outlet on  
top.  
MO  
DE  
AU  
DIO  
ALA  
ALA  
RM  
H
DD  
2
RE  
C
3
4
ZO  
OM  
FR  
EE  
ZE  
SE  
AR  
CH  
TE  
LE  
WD  
NU  
E
VIEW  
T
A
L
V
RE  
CO  
SR  
D-  
47  
MO  
DE  
AU  
DIO  
ALA  
AL  
AR  
M
HDD  
2
RE  
3
5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for air  
circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)  
4
ZO  
OM  
FR  
EEZ  
E
SE  
AR  
TE  
CH  
L
WID  
NU  
E
VIE  
W
T
A
L
V
RE  
CO  
SR  
D-  
47  
MO  
DE  
AU  
DIO  
ALA  
AL  
AR  
M
HDD  
2
RE  
C
3
4
ZO  
OM  
FRE  
EZ  
E
SE  
AR  
CH  
TE  
LE  
WD  
NU  
E
6. Please maintain the temperature inside the rack or surrounding areas between 0°C ~  
40°C (32°F ~ 104°F) as shown in the figure 1.  
VI  
EW  
Rack Mount Instructions - The following or similar rack-mount instructions are  
included with the installation instructions :  
M
O
D
E
A
U
D
IO  
A
LA  
A
R
L
M
A
R
M
H
D
D
N
E
TW  
O
R
K
2
R
BA  
E
C
C
K
U
P
R
E
C
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the  
operating ambient temperature of the rack environment may be greater than room  
ambient. Therefore, consideration should be given to installing the equipment in an  
environment compatible with the maximum ambient temperature (Tma) specified by  
the manufacturer.  
3
4
Z
O
O
M
F
R
E
E
Z
E
S
E
A
R
T
C
H
E
L
E
M
E
N
W
U
ID  
E
V
IE  
W
DIGIT  
AL VID  
EO R
ER  
SRD-  
470D  
[Figure 2]  
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the  
amount of air flow required for safe operation of the equipment is not compromised.  
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is  
not achieved due to uneven mechanical loading.  
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit  
and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.  
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.  
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should  
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).  
English _13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1133 1133  
2010-04-30 오후 6:06:4488  
installation  
HDD ADDITION  
You can install additional HDDs.  
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product  
damage.  
Please consult your provider for further information on HDD installation since improper installation or settings may  
damage the product.  
Number of HDDs supported : SRD-470 : Default 1 HDD + Up to 1 HDD added  
SRD-470D : Default 1 HDD  
Make sure to unplug the power cord from the wall outlet before proceeding with the installation.  
Cautions for data loss (HDD care)  
J
Please pay attention so that the data inside the HDD is not damaged.  
Before adding a HDD, please check the compatibility with this DVR product.  
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.  
Please ensure that the HDD is free from such shock.  
We are not liable for any damage to the HDD incurred by user’s carelessness or miss use..  
Cases might cause damage to HDD or recorded data  
To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.  
Data may be lost due to external impacts during disassembly or installation of the DVR.  
HDD may be damaged if the DVR is suddenly stopped by a power cut or power off during operation.  
HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.  
Cautions when adding a HDD  
1. When adding a HDD, ensure that the cable does not get caught or the insulation does not come off.  
2. Pay attention so as not to lose the disassembly screws or accessories.  
If the screws or accessories are not put together correctly, the product may breakdown or not operate properly.  
3. Please check the HDD compatibility before adding a HDD.  
Please contact your nearest dealer to obtain the list of compatible devices.  
14_ installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1144 1144  
2010-04-30 오후 6:06:5511  
1. First, loosen the screws on both sides and remove  
the cover.  
2. Loosen the left and right screws on the lower hard  
disk bracket to remove it.  
3. Insert the additional hard disk into the bracket and  
fix it using the provided screws.  
Hard disk bracket  
Master hard disk  
English _15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1155 1155  
2010-04-30 오후 6:06:5511  
installation  
4. Insert the bracket where the additional hard disk is  
inserted into the lower bracket and fix it using the  
provided screws.  
5. When done, connect the power cable and connect  
the signal cable (SATA cable) to the connector for  
the main board.  
SATA2  
SATA1  
6. Check if the connectors are properly connected  
and there is no problem with wiring, and close the  
cover and fix it with screws.  
16_ installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1166 1166  
2010-04-30 오후 6:06:5577  
connecting with other device  
CONNECTING THE VIDEO, AUDIO, AND MONITOR  
VIDEO IN  
AUDIO OUT  
VIDEO OUT(VGA)  
VIDEO OUT  
AUDIO IN  
MONITOR  
SPOT OUT  
CONNECTING THE USB  
1. There is one USB port at the front and one at the back of the product.  
2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.  
3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >  
Storage Device”. (Page 44)  
4. This product supports hot-plugging, which connects/removes the USB device during the system operation.  
If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.  
J
CONNECTING POS DEVICE  
1. You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with  
a RS-232C cable.  
2. Connection setup for the RS-232C port is available in “Menu > Device > POS Devices”, press the  
<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit and Transfer Type>. (Page 47)  
English _17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1177 1177  
2010-04-30 오후 6:07:0033  
connecting with other device  
CONNECTING THE ALARM INPUT/OUTPUT  
Connecting the alarm input signal  
Connection port for the alarm input signal.  
Connect one strand of the sensor signal line (two  
strands) to the alarm input port and connect the other  
to the [G] port.  
Connecting the alarm output signal  
Connection port for the alarm output signal.  
Connect one strand of the sensor signal line  
(two strands) to the alarm output port and connect  
the other to the [COM] port.  
ALARM IN ALARM OUT  
CONNECTING THE RS485 DEVICE  
Connect the rear [RS485 +, –] ports to the external device.  
ex) you can connect and control the PTZ camera  
M
which supports the RS485 communication.  
Check if the RS485 device is compatible with the  
product first.  
Pay attention not to change the polarity (+/-) of the  
RS485 device when connecting it.  
Depending on camera’s type, connection polarity can  
be different.  
For further information, refer to the respective PTZ  
Camera’s documentation.  
RS485  
18_ connecting with other device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1188 1188  
2010-04-30 오후 6:07:0055  
CONNECTING THE NETWORK  
Connecting to Internet through Ethernet (10/100/1000BaseT)  
RJ-45 Ethernet Cable  
(Direct Cable)  
INTERNET  
Back Bone  
Hub/Switcher  
Windows  
Network Viewer  
Hub/Switcher  
Connecting to the Internet using the router  
INTERNET  
xDSL or Cable  
xDSL or Cable  
Modem  
Modem  
Router  
External Remote  
PC  
DDNS Server  
(Data Center)  
English _19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1199 1199  
2010-04-30 오후 6:07:0066  
connecting with other device  
Connecting to Internet through ADSL  
RJ-45 Ethernet Cable  
(Direct Cable)  
INTERNET  
Phone(ADSL) Line  
ADSL MODEM  
Windows  
Network Viewer  
Hub/Switcher  
20_ connecting with other device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2200 2200  
2010-04-30 오후 6:07:0088  
live  
GETTING STARTED  
Starting the system  
1. Connect the power cable of the DVR to the wall outlet.  
2. Press the Power button on the front panel.  
REC  
3. You will see the initialization screen.  
The initialization process will last about 1 minute.  
If a new HDD is installed, the initialization process may  
take longer.  
REC  
4. The live screen appears with a beep.  
Shutting Down the System  
You can shut down the system only if you have logged in to the DVR.  
You require permission to shut down the system if you are not logged in as admin.  
1. Press the [POWER] button on the remote control or the  
front panel, or right-click to display the context sensitive  
menu and select <Shutdown>.  
2. The “Shutdown” confirmation window appears.  
Shutdown  
Are you sure to shutdown?  
OK Cancel  
3. Use the arrow keys on the remote control or the front panel  
to move to <OK> and press the [ENTER] button or click  
<OK>.  
The system will shut down.  
For the permission management, refer to “Permission  
M
Management > Setting Permissions”. (Page 37)  
English _21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2211 2211  
2010-04-30 오후 6:07:0099  
live  
Login  
To access a DVR or restricted menu, you should have logged in to the DVR.  
1. In live mode, right-click any area of the screen.  
You will see the context sensitive menu as in the right  
figure.  
Scene Mode ꢁ  
Audio Off  
Freeze  
Stop Alarm  
Record  
Play  
Search  
Backup  
Main Menu  
Shutdown  
Hide Launcher  
Login  
2. Click <Login>.  
The login dialog appears.  
You can also see the login dialog to access a desired menu  
by pressing the [MENU] button on the remote control or  
the front panel.  
Login  
x ID  
admin  
OK  
x Password  
The login dialog will also appear if you press a menu button on  
the remote control or the front panel of the DVR when the  
corresponding menu requires logging in.  
Cancel  
After logged in, press [RETURN] on the remote control to display  
the logout dialog.  
By default, initial ID and password are set to “admin”, and “4321”.  
For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 37)  
M
Locking All Buttons  
This will restrict access to all buttons available in the DVR.  
1. In Live mode, press buttons in the order of [STOP]  
[FREEZE] [STOP] [FREEZE] [MENU].  
All buttons will be locked.  
2. In the lock condition, press any button to display a dialog  
where you are prompted to enter the password for  
unlocking the buttons.  
Key Lock Password  
x ID  
admin  
x Password  
OK  
Cancel  
The button lock will be released if you enter the admin  
password.  
22_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2222 2222  
2010-04-30 오후 6:07:1144  
LIVE SCREEN CONFIGURATION  
Icons on the Live Screen  
You can check the status or operation of the DVR with the icons on the live screen.  
2010-01-01 00:00:01  
CAM 01  
Name  
Description  
Current Date, Time  
Displays the current time and date.  
Login Information  
When you are logged in, the “LOG ON” icon will be displayed.  
Displayed if the zoom function is activated.  
Displayed if you press the Pause button.  
Displayed in Auto Sequence mode where all channels are switched at the  
Screen Mode  
specific time interval.  
Displayed if the recording is in process.  
M To cancel the recording, enter the password.  
Displayed if there is a problem with the cooling fan.  
Displayed if the HDD is full and the DVR has an insufficient space to record.  
Displayed if no HDD is installed or the existing HDD should be replaced.  
Displayed if the HDD needs a technical examination.  
System Operation  
Video Input Status  
Displayed if a new firmware is found from the network.  
Displayed if no input is entered in the condition that the camera is set to <ON>.  
Nothing will be displayed on the screen if the camera is set to <OFF>.  
Camera Name/ Channel  
Displays the camera name and the changed channel, if any.  
Displays the resolution of the recording screen. (Page 52)  
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.  
Displays AUDIO ON/MUTE.  
Not displayed in video mode if deactivated.  
Camera Operation  
If the sensor is set to <ON>, the input signal will be displayed on the screen of  
the connected channel.  
Displayed if a motion detected in the condition that the motion detection is set to  
<ON>.  
Displays the current record mode from Record/Event/Schedule.  
English _23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2233 2233  
2010-04-30 오후 6:07:2200  
livEerror Information  
If you turn on the system when the internal HDD is not connected or an error occurs, the “HDD FAIL” icon  
(
) will be displayed on the top left corner. In this case, make sure you contact the service center for  
assistance as this may cause a failure of recording, playback or backup.  
If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and  
the fan error icon (  
works.  
) will be displayed on the top left corner. In this case, check to see if the internal fan  
As a fan error can shorten the product life, make sure you contact the service center for assistance.  
If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.  
M
Live Screen Menu  
In addition to the buttons on the front panel or the remote control, you can access a desired menu by right-  
clicking the mouse any area in live mode.  
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/  
logout, screen split mode and DVD operation mode.  
Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.  
M
Scene Mode ꢁ  
Scene Mode ꢁ  
PTZ Control  
Audio Off  
ZOOM  
Freeze  
Audio  
Stop Alarm  
Record  
Freeze  
Stop Alarm  
Record  
Play  
Play  
Search  
Search  
Backup  
Backup  
Main Menu  
Shutdown  
Main Menu  
Shutdown  
Hide Launcher  
Login  
Hide Launcher  
Login  
PTZ  
Alarm  
Freeze  
< Single Mode Menu >  
< Split Mode Menu >  
Split Mode Menu  
The context sensitive menu in split mode differs, depending on the login/logout status.  
Scene Mode  
Spot Out  
Audio Off  
Freeze  
1
2
3
4
Stop Alarm  
Record  
5
6
Play  
7
Search  
8
Backup  
9
Main Menu  
Shutdown  
Hide Launcher  
Logout  
10  
11  
12  
13  
24_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2244 2244  
2010-04-30 오후 6:07:2222  
Menu  
Scene Mode  
Spot Out  
Audio On/Off  
Freeze  
Description  
Refer to “Live Mode”. (Page 27)  
Refer to “Spot Out”. (Page 29)  
Refer to “Audio ON/OFF”. (Page 30)  
Refer to “Freeze”. (Page 30)  
Stop Alarm  
Record/Stop  
Play  
Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 30)  
Starts/stops the standard recording.  
Plays the search result (data). Refer to “Search & Play > Play”. (Page 69)  
Refer to “Search & Play > Search”. (Page 66)  
Refer to “Using the DVR > Setting the Backup”. (Page 56)  
Accesses the main menu. Refer to the Using the DVR section. (Page 32)  
Turns down the DVR.  
Search  
Backup  
Main Menu  
Shutdown  
Show/Hide Launcher  
Login/Logout  
Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 26)  
You can log in or out.  
Single Mode Menu  
The single mode menu is available only in Single Mode.  
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.  
Full Screen  
1
Spot Out  
PTZ Control  
ZOOM  
2
3
Audio  
Freeze  
Stop Alarm  
Record  
Play  
Shutdown  
Hide Launcher  
Logout  
PTZ  
Alarm  
Freeze  
Menu  
Description  
Select and click a desired channel in Split mode to switch to the full screen of the selected  
Full Screen  
channel.  
Accesses the PTZ Control menu. The PTZ menu is activated only in One-Channel Live mode.  
(Page 64)  
Enlarges the selected image. (Page 29)  
PTZ Control  
ZOOM  
English _25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2255 2255  
2010-04-30 오후 6:07:3300  
live  
View the Launcher Menu  
The Launcher menu appears on the bottom of the live screen.  
1. In Live mode, right-click to display the context menu and  
select <Show Launcher>.  
2. Move the cursor to the bottom and click a desired item in  
the Launcher menu.  
If no input is entered for 10 seconds, the menu will disappear.  
M
The Launcher menu can be accessed only by using the mouse.  
PTZ Alarm Freeze  
Menu  
Description  
Displays the current time and date.  
Date/Time  
The indication of AM/PM is displayed if you set 12 hours for the time format in  
System > Date/Time/Language > Time”. (Page 32)  
Screen Mode  
Displays in the sequence of 4-split, PIP and Auto Sequence.  
Menu Expansion Button Click to display the hidden menu to the right.  
Audio  
Zoom  
PTZ  
Turns ON/OFF the sound of the selected channel.  
Enlarges the selected area. This is available only in Single Live mode.  
Runs the PTZ Control launcher.  
Alarm  
Freeze  
Play  
Stops the alarm if it's activated.  
Freezes the Live screen temporarily.  
Enters Play mode if a file to play exist, and if not, enters Search mode.  
Start/End recording the Live screen.  
Record  
26_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2266 2266  
2010-04-30 오후 6:07:3333  
LIVE MODE  
Displays 4 live video images in 3 different modes.  
Switching the screen mode  
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in  
the context menu.  
Press the [MODE] button on the front panel or the remote control to switch the mode in the sequence of the  
launcher menu items.  
CH1  
CH3  
CH2  
CH2  
CH4  
CH1  
CH1  
4-split mode  
PIP  
Auto Sequence  
Switching the screen automatically  
With SRD-470/470D, you can display 4 live single screens in sequence.  
4
CH1  
1
Single mode  
In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be  
M
conducted at the set interval. (Page 42)  
English _27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2277 2277  
2010-04-30 오후 6:07:3355  
live  
Channel Setting  
You can display the channel in a desired area of a split screen.  
1. Place the cursor over the camera name of each channel to display the <  
> key to the right on the screen.  
2. Click a camera name to display a channel list where you can select a different channel.  
3. Select a desired channel and click it.  
The current channel will be switched to the selected one.  
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also  
change the channel position.  
Ex : if switching CH 1 to CH 4  
CH4  
CH3  
CH2  
CH1  
CH1  
CH3  
CH2  
CH4  
Switching to Single Mode  
When in split mode, select and double-click a desired channel to switch to its Single mode.  
Press the number corresponding to a desired channel on the front panel or the remote control to switch to its  
Single mode.  
Refer to “Remote Control > Using the numeric buttons”. (Page 12)  
Ex : If double-clicking CH 3 or pressing the number “3” on the remote control or the front panel.  
CH1  
CH3  
CH2  
CH4  
CH3  
28_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2288 2288  
2010-04-30 오후 6:07:3366  
SPOT OUT  
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out  
port.  
Selecting a Spot Out mode  
If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you  
can select a output screen mode.  
1. In Live mode, right-click any area on the screen.  
Scene Mode ꢁ  
Spot Out  
Audio Off  
Freeze  
Spot Out 1  
Auto Sequence  
Single  
The Live menu appears.  
CH1  
CH2  
CH3  
CH4  
2. Click Spot Out.  
Stop Alarm  
Record  
Supports the Spot output in Single screen with Auto  
Sequence mode.  
Play  
Search  
Backup  
Main Menu  
Shutdown  
The Spot output is supported only for a designated channel.  
For the Spot Out port of a model, refer to “Part Names and  
Functions (Rear)”. (Page 9)  
Hide Launcher  
Logout  
< Multichannel Live Menu >  
ZOOM  
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to  
enlarge it twice.  
1. Select <ZOOM> in the right-click menu.  
Press the [ZOOM] button on the front panel or the remote control, or simply click <  
> in the launcher  
menu. The zoom box appears.  
2. Use the direction keys, or drag and drop to specify an area to enlarge.  
3. Press the [ENTER] button, or double-click the selected area to enlarge it twice.  
In the enlarged image, use the direction buttons (ꢀꢁ◄ ►) on the remote control or the front panel to move the  
enlarged area.  
4. Press the [ZOOM] button on the front panel or the remote control, or simply click <  
> in the launcher  
menu to release the zoom.  
English _29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2299 2299  
2010-04-30 오후 6:07:3377  
live  
AUDIO ON/OFF  
You can turn the sound on/off corresponding to the channel in Live mode.  
AUDIO ON/OFF in Single mode  
Click the audio icon ( ) on the screen, or press the [AUDIO] button on the front panel or the remote control  
to turn it on/off.  
Only the channel where <AUDIO> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live  
M
mode that you can use to turn the sound on/off.  
FREEZE  
This is available only in Live mode, this pauses playing the Live image temporarily.  
Freeze  
1. Press the [FREEZE] button on the front panel or the remote control, or click <  
> in the launcher  
menu.  
The playback of the image is stopped temporarily.  
Freeze  
2. Press the [FREEZE] button again, or click <  
>.  
This will release the freeze.  
EVENT MONITORING  
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs.  
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 48)  
If multiple events occur simultaneously, the screen will switch to a split mode.  
- 2~4 events : 4-split mode  
If the second event occurs within the set time of <Event Display>, the first event will last until the second  
one is terminated. (Page 48)  
Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.  
Event occurrence  
5 seconds  
Stop alarm  
CH1  
30_ live  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3300 3300  
2010-04-30 오후 6:07:4466  
Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first  
event occurred in CH 1.  
Event occurrence  
4 seconds  
9 seconds  
Stop alarm  
CH1  
CH2  
CH1  
Press the [ALARM] button to reset the alarm settings and to release the event mode.  
M
If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will  
be performed.  
English _31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3311 3311  
2010-04-30 오후 6:07:4477  
using the DVR  
You can setup the system properties, devices, and options for recording, event,  
backup and network.  
SYSTEM SETUP  
You can setup Date/Time/Language, Permission, System Properties and Log.  
Date/Time/Language  
You can check and setup the current Date/Time and time related properties, as well as the language used for  
the interface on the screen.  
Setting the Date/Time/Language  
Set the Date/Time/Language  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or on the  
front panel.  
If not logged in, it prompts with login window.  
Refer to “Login”. (Page 22)  
2. Use the left/right buttons (◄ ►) to select the <System>.  
Logout  
Exit  
System property setup menu is selected.  
3. Use the up/down buttons (ꢀꢁ) to select <Date/Time/  
Language> and press the [ENTER] button.  
System  
Date/Time/Language  
4. Select <Date/Time/Language>.  
Permission Management  
System Management  
Log Information  
A dialog to setup Date, Time and Language.  
5. Use direction buttons (ꢀꢁ◄ ►) to select an item to set  
and make your changes.  
Date : Sets the date that will appear on the screen.  
You can select the date format.  
Time : Sets the time and its format that will appear on the  
screen.  
Date/Time/Language  
Date/Time/Language  
Holiday  
x Date  
2010-01-01  
YYYY-MM-DD  
24 Hours  
x Time  
08:14:24  
GMT+09:00  
Setup  
Select either one from <24 Hours, 12 Hours (AM/PM)>.  
x Time Zone  
x Time Sync.  
x DST  
Time Zone : Sets the time zone of your area based on the  
Greenwich Mean Time (GMT).  
Dec First (Sun) 0  
Dec First (Sun) 0  
x Language  
English  
GMT (Greenwich Mean Time) is standard World Time and the basis  
of world time zone.  
OK  
Cancel  
Time Sync. : You can set the DVRs current time  
synchronized to a selected <Time Server> regularly if you select to use <Time Server>.  
In this case, <Date/Time/Language> setup does not allow time adjustment.  
32_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3322 3322  
2010-04-30 오후 6:07:4477  
- Time Server : Enter an IP or URL address of the time  
server.  
Date/Time/Language  
Date/Time/Language  
Holiday  
- Last Sync Time : Displays the most recent  
synchronization time from the selected time server.  
- Activate as Server : Set to <Use> to allow the DVR to act  
as a Time Server for other DVRs.  
x Time Synchronization Setup
x Synchronization  
x
x Time Server  
x
x Last Sync Time  
x
x Activate as Server  
x
Use  
203.248.240.103  
Fail  
Use  
DST : Set up Daylight Saving Time with its period to make  
the time earlier than the GMT of its time zone by 1 hour  
during the set period.  
Language : Select your language. Sets the language for the  
interface.  
OK  
OK  
Cancel  
Cancel  
x Language  
English  
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,  
Turkish, Czech, Danish, and Swedish are available.  
6. When the Date/Time/Language setup is done, press <OK>.  
You can also use numeric buttons on the remote control or front panel to enter values for Date, Time and other  
M
numeric fields.  
Setting Holiday  
You can set specific dates to Holidays according to your preferences.  
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Date/Time/Language> window to select <Date/Time/Language>, and  
press the [ENTER] button.  
A calendar for Holiday setup appears.  
4. Select <Holiday>.  
Date/Time/Language  
Holiday  
Date/Time/Language  
5. Use the left/right <  
> buttons to select year or month,  
2010  
Sun Mon Tue  
Jan  
and press the [ENTER] button.  
Wed Thu  
Fri  
1
Sat  
2
3
4
5
6
7
8
9
10  
17  
24  
31  
11  
18  
25  
12  
19  
26  
13  
20  
27  
14  
21  
28  
15  
22  
29  
16  
23  
30  
OK  
Cancel  
6. Use direction buttons (ꢀꢁ◄ ►) to select a desired date,  
and press the [ENTER] button.  
Date/Time/Language  
Holiday  
Date/Time/Language  
You will see the “Setting Holiday” screen.  
2010  
Jan  
Ex : Select January 11th and check on <1/11> only to make  
every January 11th a holiday. Check both on <1/11> and <Jan  
2nd Mon> to make every January 11th and 2nd Monday of  
January holidays.  
Setting Holiday  
1 / 11  
Jan 2nd Mon  
24  
31  
25  
29  
30  
OK  
Cancel  
26  
27  
28  
7. When the Holiday setup is done, press <OK>.  
OK  
Cancel  
Using the Calendar  
Using the mouse may help make setup easier.  
{
Select year and month.  
Select the left/right <  
adjust by 1 year/month.  
> key on the left/right side of year/month and press [ENTER] button to  
|
Use direction buttons to select a date and press [ENTER] button.  
A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event  
Search.  
English _33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3333 3333  
2010-04-30 오후 6:07:5511  
using the DVR  
Permission Management  
You can set permissions of each user over the DVR's specific function and settings.  
Setting the Administrator  
You can set and change Administrators ID and password.  
The administrator can use and set all menu items and functions.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
Permission Management  
move to <Permission Management>, and press  
Admin  
Group  
User  
Setup  
[ENTER] button.  
x ID  
admin  
x Password  
********  
********  
4. Select <Admin>.  
x Conrm P/W  
A dialog for Admin ID and Password input appears.  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and set the ID and password.  
OK  
Cancel  
By default, initial ID and password are set to “admin”, and  
M
4321”.  
6. When the administrator setup is done, press <OK>.  
Using Virtual Keyboard  
{
|
}
For alphanumeric inputs, the virtual keyboard window  
appears.  
`
1
w
s
2
e
d
c
3
r
4
t
5
6
u
j
7
i
8
o
l
9
p
;
0
[
-
]
=
\
Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
q
a
z
y
h
Del  
character, and press the [ENTER] button.  
f
g
b
k
,
Caps Lock  
Shift  
x
v
n
m
.
/
In the upper text input box of the virtual keyboard, there  
displays a list of candidate words containing the selected  
character.  
Space  
Ctrl  
OK  
Cancel  
~

Select a word from the list, or use the keyboard to enter the  
whole word.  
If there are many of candidate words, use <  
,
> buttons to move between them forward and backward.  
You can use mouse wheel and jog shuttle button too.  
Select <OK>.  
Entered word is applied.  
For upper case letters, use <Caps Lock> button.  
For special characters, use <Shift> button.  
Using the virtual keyboard is the same to a normal keyboard use in your region.  
You can enter only lower-case alphabets and numeric values for the user ID.  
For the password, use alphabets and special characters excluding < > and <>.  
\
You can use number buttons on the remote control or front panel.  
34_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3344 3344  
2010-04-30 오후 6:07:5544  
Setting the Group  
You can create user groups and setup permissions for those user groups.  
You can register a user for each group in <User>.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
Permission Management  
move to <Permission Management>, and press  
Group  
Admin  
User  
Setup  
[ENTER] button.  
x Group  
Add  
Delete  
Rename  
Group Authority  
Live View  
Search  
4. Select <Group>.  
Setup  
Setup  
Setup  
Setup  
PTZ  
A window for <Add>, <Delete>, <Rename>, and  
Backup  
Menu  
<Group Authority> setup appears.  
Record Lock  
Remote Alarm Out  
Shutdown  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and set the value.  
OK  
Cancel  
Add, Delete, Rename : You can add, delete, rename a  
group or modify the permissions given to the group.  
The virtual keyboard appears when <Add> or <Rename> was selected.  
You can add up to 10 groups.  
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already  
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10  
groups.  
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts  
belonging to that group.  
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.  
For entering a group name, refer to “Using Virtual Keyboard”. (Page 34)  
Group Authority : Sets permissions to access menu items of each group.  
Users of a group can access checked functions.  
6. When the group setup is done, press <OK>.  
To set the group authority  
You can set the permissions of the group users to access the menu according to the channel.  
1. Select a menu to which the group permission is assigned.  
Permission Management  
The menu where the group permission is assigned will be  
Group  
Admin  
User  
Setup  
displayed in the Live menu when a group user logs in.  
Group  
ABC  
Add  
Delete  
Rename  
x
Group A
Channel Setup  
Live V
Searc
Backu
Menu  
Live View : You can set the permission to access the Live  
screen according to the channel.  
All  
1
2
3
4
Search : You can set the permission to access the Search  
menu according to the channel.  
Reco
Cancel  
n  
OK  
Backup : You can set the permission to access the Backup  
menu according to the channel.  
OK  
Cancel  
Menu : You can set menus accessible with a specific  
permission.  
Group users can access the permitted menus only.  
Select a menu to display the Menu Permission screen.  
Permission Management  
Menu Permission  
All  
System  
t
B
a
c
k
u
p
N
e
t
w
ork  
D  
evice  
Record  
Eve  
n
Record Lock, PTZ, Remote Alarm Out, Shutdown : Select  
an item so that the item will be added to the permissions.  
Date/Time/Language  
Date/Time/Language  
Holiday  
Settings  
System Management  
System Information  
Log Information  
2. Select <OK>.  
System Log  
Event Log Backup Log  
Select and assign a group user so that the user can  
access the specified menu.  
OK  
Cancel  
English _35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3355 3355  
2010-04-30 오후 6:07:5566  
using the DVR  
To restrict the user permissions  
If the admin restricts all permissions of an added group, the users belonging to that group can access only  
the default minimum menus and can change the users own password only.  
1. Start the DVR.  
If all permissions are restricted, only the Login dialog  
should appear.  
2. Log in with a registered user ID.  
Login  
x ID  
abc  
x Password  
OK  
Cancel  
3. Right-click any area on the screen.  
If all permissions are restricted, only the accessible context  
menus should appear.  
Scene Mode  
Audio Off  
Freeze  
Stop Alarm  
User Menu  
Hide Launcher  
Logout  
To change the user password  
If you log in with a user account that is restricted to access the menu, you can change your own password  
only.  
1. Log in with your account.  
Permission Management  
User  
2. Select <User Menu>.  
The Permission Management setup screen appears.  
x ID  
abc  
x Password  
x Conrm P/W  
********  
********  
3. Select <Permission Management>.  
The Password setup dialog appears.  
4. Enter a new password.  
5. Select <OK>.  
OK  
Cancel  
You change to the password will be applied.  
36_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3366 3366  
2010-04-30 오후 6:07:5599  
Setting the User  
Users can be added only if a group was created in <Group> menu.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <Permission Management>, and press  
[ENTER] button.  
Permission Management  
User  
Admin  
x Group  
Group  
Group  
All Group  
Name  
Setup  
Add  
Delete  
ID  
Viewer  
4. Select <User>.  
A window for Add User appears.  
5. Use direction buttons (ꢀꢁ◄ ►) to select <Add> from the  
window.  
Previous/Next Page  
A window for “Add User” appears.  
OK  
Cancel  
You can configure the Network Viewer settings including  
name, ID, viewer, Select Group and password.  
Result of the user setup appears in the <User> window.  
To change the user property, use “Edit User”.  
The “Edit User” window appears when you select a  
desired item to be changed in the <User> window.  
Permission Management  
User  
Admin  
x Group  
Groux Name  
Group  
Setup  
AddUser  
Add  
Delete  
Kim
ksh  
Viewer : If you select <Use>, you will be given access to the  
x ID  
x Viewer  
Not Used  
ABC  
Web Viewer and Network Viewer.  
x Select Group  
x Password  
x Conrm  
********  
********  
Refer to “Connecting Web Viewer”. (Page 71)  
OK  
Cancel  
For more information about use of Network Viewer, refer to the  
Previous/Next Page  
Network Viewer's user guide. (Page 8)  
OK  
Cancel  
6. When the user setup is done, press <OK>.  
Setting Permissions  
You can set restricted access for all general users.  
Items with restrictions will require logging in for use.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <Permission Management>, and press  
[ENTER] button.  
Permission Management  
Setup  
Admin  
Group  
User  
Restricted Access  
Live View  
Backup  
Remote Alarm Out  
Record Lock  
Shutdown  
Search  
All  
PTZ  
4. Select <Setup>.  
Restriction on Network Access  
The Restricted Access, Restriction on Network Access,  
Auto Log out, Manual Input of ID setup screen appear.  
All Network  
Web Viewer  
x Auto Log out  
3 min  
ON  
x Manual Input of ID  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and set the value.  
OK  
Cancel  
Restricted Access : All menu items allowed for a user can  
be set with restricted access.  
- Checked ( ) : Restricted  
- Not checked ( ) : Accessible  
If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>  
setting.  
If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group  
Authority> setting.  
Restriction on Network Access : Restricts remote access from a <Restricted Access> network.  
- All Network : Restricts all access instances via Network Viewer and Web Viewer.  
- Web Viewer : Restricts access via the Web Viewer.  
Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of  
time.  
English _37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3377 3377  
2010-04-30 오후 6:08:0022  
using the DVR  
Manual Input of ID : Prompts you to enter the user ID  
manually for the login process.  
- Checked ( ) : Encloses the registered user IDs with the  
[
½
] symbols.  
Login  
x ID  
Use the virtual keyboard to enter the user ID.  
6. When the permission setup is done, press <OK>.  
*****  
x Password  
OK  
Cancel  
System Management  
You can check the system version, update to a newer version, as well as data backup and initialization.  
Checking the System Information  
You can check the current system version, broadcasting system, MAC address. You can update the system.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
System Management  
move to <System Management>, and press [ENTER]  
System Information  
Settings  
button.  
System Information  
x Software Version  
V1.00h_100315180929  
x Broadcast Format  
NTSC  
4. Check the Version, Broadcast Format, and MAC Address.  
x MAC Address  
00:00:F0:54:FF:FF  
System Information : Shows the current systems  
information.  
S/W Upgrade  
Upgrade  
x Device  
Network  
x Version  
No S/W Data  
The values can not be changed by a user.  
S/W Upgrade : Updates the DVRs software up to date.  
Previous  
Ex : If you connect to a storage device that has upgradable software  
installed, and return to the <System Management> menu, the  
current software version will be displayed.  
System Management  
System Information  
Settings  
System Information  
x Software Version  
x Broadcast Format  
x MAC Address  
V1.00h_100315180929  
NTSC  
00:00:F0:54:FF:FF  
S/W Upgrade  
Upgrade  
x Device  
v3.1.0.4  
x Version  
V1.00h_100320180929  
Previous  
38_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3388 3388  
2010-04-30 오후 6:08:0055  
Updating the Software  
1. Connect a device storing the software to be updated.  
System Management  
System Information  
(It may take about 10 seconds to recognize the device.)  
Settings  
System Information  
Upgradeable devices include USB memory, CD/DVD and  
x Software Version  
V1.00h_100315180929  
System Upgrade  
x Broa
network device.  
x MAC
Current Version  
V1.00h_100315180929  
New Version  
V1.00h_100320180929  
To update the network, the current DVR should have been  
connected to the network.  
S/W
Do you want to upgrade?  
x Devi
OK  
Cancel  
x Vers
Upgrade via the proxy server may not be enabled due to the  
restricted access.  
Previous  
2. Select <System Management> from <System> window.  
3. Select <System Information>.  
4. When the recognized device appears, select <Upgrade>.  
The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is  
same to or older than that of <S/W Upgrade>.  
5. Press <OK> in the “System Upgrade” window.  
System Management  
System Information  
While updating, it shows the progress.  
Settings  
System Information  
Updating progresses with 3 steps as shown in the figure.  
x Software Version  
V1.00h_100315180929  
x BroadcaS/WUpgrade
x MAC Ad
Software upgrading...  
S/W Up
x Device  
x Version  
Previous  
System Management  
System Information  
Settings  
System Information  
x Software Version  
V1.00h_100315180929  
x Broadca
S/W Upgrade  
x MAC Ad
Software upgrading...  
S/W Up
Do not turn off during the upgrade.  
x Device  
x Version  
Previous  
6. When the updating is done, it automatically restarts.  
Do not turn the power off until it finishes restarting.  
If “Upgrade Failed” appears, retry from the step 4.  
M
When you experience continued failure, consult the service  
center for assistance.  
English _39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3399 3399  
2010-04-30 오후 6:08:0088  
using the DVR  
Settings  
You can copy and import the DVR settings by using a storage media.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
move to <System Management>, and press [ENTER]  
button.  
System Management  
Settings  
System Information  
x Storage Device  
1932 MB (Remained Capacity)  
Export  
Import  
x DVRUSB  
10041400  
4. Select <Settings>.  
x USBDVR  
Include Network Settings  
A window of storage device and load factory default  
appears.  
x Load Factory Default  
Default  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and export or import settings data to a storage  
device.  
Previous  
Storage Device : Shows the connected storage device.  
Export : Exports DVR settings to the connected storage device.  
Import : Imports DVR settings from the storage device and applies to the DVR.  
If <Include Network Settings> is checked, the network settings will be imported too.  
Load Factory Default : If <Default> is selected, a  
Press <OK> to initialize the system to the factory default.  
System Management  
confirmation dialog for “Load Factory Default” prompts.  
Settings  
System Information  
x Storage Device  
1932 MB (Remained Capacity)  
Load Factory Default  
x DVR
6. To move to the previous menu, press <Previous>.  
x USB
Sure to Default Setting?  
OK  
Cancel  
x Load
Previous  
Log Information  
You can browse logs on the system and events.  
System Log  
System Log shows log and timestamp on every system start up, system shutdown, and changes on system  
settings.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
Log Information  
move to <Log Information>, and press [ENTER] button.  
System Log  
Event Log  
Backup Log  
Search  
Search Day  
First Page  
2010-01-01  
Last Page  
4. Select <System Log>.  
Type View all  
No.  
Log List  
Date/Time  
Refer to “Using the Calendar”. (Page 33)  
Click on the calendar < > to display the calendar window.  
Type : When there are too many logs, you can display logs of  
the desired format by selecting the type.  
Previous/Next Page  
Previous  
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,  
and press <Search>.  
40_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4400 4400  
2010-04-30 오후 6:08:1122  
Event Log  
Event log shows recorded events on alarms, motion detections and video loss.  
It also shows the log and its timestamp.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <System> window to  
Log Information  
move to <Log Information>, and press [ENTER] button.  
Event Log  
System Log  
Backup Log  
Search Day  
First Page  
2010-01-01  
Last Page  
Search  
All CHs  
4. Select <Event Log>.  
CH  
Type  
Date/Time  
View all  
No.  
Log List  
5. Use direction buttons (ꢀꢁ◄ ►) to move to the desired  
7
6
5
4
3
2
1
Motion Detection [CH 1]  
Motion Detection [CH 2]  
Motion Detection [CH 3]  
Motion Detection [CH 4]  
Motion Detection [CH 3]  
Motion Detection [CH 2]  
Motion Detection [CH 1]  
2010-01-01 00:02:14  
2010-01-01 00:02:14  
2010-01-01 00:02:14  
2010-01-01 00:02:18  
2010-01-01 00:02:18  
2010-01-01 00:02:18  
2010-01-01 00:02:18  
item.  
6. Set Search Day, Channel and Type and the press  
<Search>.  
Previous/Next Page  
Refer to “Using the Calendar”. (Page 33)  
Previous  
Click on the calendar < > to display the calendar window.  
Backup Log  
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).  
Using the mouse may help make setup easier.  
3. In the <System> window, press the up/down (ꢀꢁ) button  
Log Information  
to move to <Log Information> and press the [ENTER]  
Backup Log  
System Log  
Event Log  
Search Day  
First Page  
2010-01-01  
Last Page  
~
2010-01-02  
Search  
button.  
Previous/Next Page  
No.  
User  
Date/Time  
4. Select <Backup Log>.  
5. Use the four direction buttons (ꢀꢁ◄ ►) to move to a  
desired item.  
6. Specify a search term and select <Search> in the right  
corner.  
Previous  
Backup details for the search term will be listed.  
English _41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4411 4411  
2010-04-30 오후 6:08:1155  
using the DVR  
SETTING THE DEVICE  
You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.  
Camera  
Setting the Camera  
You can set Video, Audio, Channel Name and Dwell Time of a Camera.  
Using the mouse may help make setup easier.  
1. Press the [MENU] button on the remote control or front  
Logout  
Exit  
panel.  
2. Use the left/right button (◄ ►) to select <Device>.  
Device setting menu is selected.  
Device  
Camera  
3. Use the up/down buttons (ꢀꢁ) to move to <Camera>,  
Storage Device  
Remote Device  
POS Device  
Monitor  
and press [ENTER] button.  
4. Select <Camera>.  
Camera  
Camera  
You will see a window where you can configure the  
PTZ  
camera settings including Video, Audio, Channel Name,  
Dwell Time and Progressive.  
CH  
1
Video ꢄ  
Audio ꢄ  
OFF ꢄ  
OFF ꢄ  
OFF ꢄ  
OFF ꢄ  
CH Name  
SEQ-Dwell Time Progressive ꢄ  
ON ꢄ  
ON ꢄ  
ON ꢄ  
ON ꢄ  
CAM 01  
CAM 02  
CAM 03  
CAM 04  
5 sec  
5 sec  
5 sec  
5 sec  
OFF ꢄ  
OFF ꢄ  
OFF ꢄ  
OFF ꢄ  
2
3
4
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and set the value.  
Video  
Screen Setup  
- <ON/OFF> : You can turn ON/OFF the selected  
OK  
Cancel  
channel’s camera.  
- <Covert1> : Shows information other than the video of the selected channel.  
For privacy protection, it does not display the video while the recording continues.  
- <Covert2> : Shows nothing but an empty screen while the recording continues.  
Audio  
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.  
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.  
Audio output is available for only 1 channel.  
CH Name : Up to 15 characters including blanks are allowed.  
Refer to “Using Virtual Keyboard”. (Page 34)  
SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.  
If set to <OFF>, the channel is not listed in the Auto Sequence mode.  
42_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4422 4422  
2010-04-30 오후 6:08:1177  
Progressive : You can set the progressive camera to ON/OFF.  
If you set it to <ON> for the progressive camera, screen flickering will be reduced.  
J
Screen Setup : The video appeared on the screen may vary  
depending on the channels camera, configure the DVR  
display to your preferences.  
Select a channel and adjust the  
<
(Brightness)>,  
<
(Contrast)>, and  
<
(Color)> of the selected channel.  
Press the <Init> to initialize settings back to the default 50.  
Screen Setup  
6. When the camera setup is done, press <OK>.  
CH1  
50  
50  
50  
Init  
Apply to All CH  
OK  
Cancel  
Setting the PTZ  
To use Cameras PTZ functions, ID and protocols of each camera and DVR should be matched.  
For other settings, refer to the “Remote Devices” settings. (Page 46)  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Camera  
move to <Camera>, and press [ENTER] button.  
PTZ  
Camera  
CH  
1
ID  
Protocol ꢄ  
4. Select <PTZ>.  
0
1
2
3
None  
None  
None  
None  
>
>
>
>
2
A window of PTZ settings appears.  
3
4
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
item, and select it.  
ID : Set the ID of the connected camera of each channel.  
You can easily setup by using the numeric buttons on the  
remote control or front panel.  
OK  
Cancel  
Protocol : Set the protocol of the connected camera of each  
channel.  
You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.  
M
(Page 65)  
6. When the PTZ setup is done, press <OK>.  
English _43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4433 4433  
2010-04-30 오후 6:08:1199  
using the DVR  
Storage Device  
You can check information on storage devices.  
Confirming Devices  
You can check storage devices and their free space, usage as well as status.  
Devices available are HDD, and USB devices (Memory, HDD, CD/DVD).  
Refer to “Product Specifications > Backup”. (Page 96)  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
Device  
Format  
HDD Alarm  
Device  
HDD  
No.  
1
Used/Total  
12.28G/499.37G  
Usage  
Status/Management  
Normal  
4. Select <Device>.  
Internal  
No. : Shows the assigned number of the internal HDD.  
To see the detailed positioning of the HDD according to the  
number, refer to <HDD Map>.  
HDD Map  
Used/Total : Shows the used/total capacity of the storage  
device.  
Usage : Sets the storage devices usage.  
- USB memory and storage media such as CD/DVD are used for backup purpose only.  
Status/Management : Shows the current status of the HDD, as in Normal/Check/Replace.  
OK  
Cancel  
- Normal : Available to use  
- Check : Available to use but recommended to replace  
- Replace : Requires immediate replacement.  
HDD Map : Shows the internal HDDs locations according  
HDD Map  
to assigned numbers.  
Refer to this for servicing or additional HDD installation.  
5. To move to the previous menu, press <OK>.  
OK  
<SRD-470>  
HDD Map  
OK  
<SRD-470D>  
44_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4444 4444  
2010-04-30 오후 6:08:2255  
Formatting  
You can format a storage device.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
Format  
Device  
HDD Alarm  
Device  
HDD  
Select  
1
Used/Total  
12.28G/499.37G  
Usage  
4. Select <Format>.  
Internal  
A window for selection of device for formatting appears.  
5. Use direction buttons (ꢀꢁ◄ ►) to select a device to be  
formatted.  
Format  
OK  
Cancel  
6. Select <Format> on the bottom of the screen.  
Press <OK> on the “Manage” confirmation window will  
start formatting the selected device.  
Storage Device  
Format  
Device  
HDD Alarm  
Device  
HDD  
Select  
1
Used/Total  
Usage  
12.28G/499.37G  
Internal  
7. When the formatting is done, press <OK>.  
Manage  
Formatting deletes all recordings.  
Proceed formatting?  
OK  
Cancel  
Format  
OK  
Cancel  
HDD Alarm  
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,  
and its duration.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Storage Device  
move to <Storage Device>, and press [ENTER] button.  
HDD Alarm  
Device  
Format  
4. Select <HDD Alarm>.  
1
2
BEEP  
BEEP  
x Check Alarm Output Port  
All  
A window for setting HDD check and replace output ports  
and their durations appears.  
x Duration  
OFF  
x Replace Alarm Output Port  
1
All  
2
5. Use direction buttons (ꢀꢁ◄ ►) to move to the desired  
x Duration  
OFF  
item.  
Alarm  
OK  
Cancel  
- Alarm signal will output through the alarm out port on the  
rear side when selected <1>, <2>.  
- If <BEEP> was selected, a beep will sound.  
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.  
Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm  
output port.  
Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified  
alarm output port.  
English _45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4455 4455  
2010-04-30 오후 6:08:3333  
using the DVR  
Duration : Sets the alarm duration for the alarm signal and beep sound.  
- If <BEEP> was selected, a beep will sound.  
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.  
<Check> status means that the HDD is operating but it has problems that require technical examination.  
M
(
) appears on the Live screen.  
<Replace> status means that the HDD has defect and requires immediate replacement.  
) appears on the Live screen.  
(
6. When the HDD Alarm setup is done, press <OK>.  
Remote Devices  
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
Remote Device  
move to <Remote Device>, and press [ENTER] button.  
Baudrate  
9600  
Parity  
None  
Data  
8
Stop Bit  
1
Transfer type  
Half Duplex  
4. Use direction buttons (ꢀꢁ◄ ►) to move to the desired  
item, and press [ENTER] button.  
System Keyboard  
Remote Control  
OFF  
ON  
ID  
ID  
00  
00  
5. Set the values of each communication setup of the remote  
device.  
Baudrate : Baud rate settings of the DVR, PTZ camera and  
system keyboard should be matched for proper operations.  
OK  
Cancel  
6. Make sure to match IDs of the DVR, System Keyboard  
and Remote Control, and press <OK>.  
For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 12)  
M
POS Devices  
You can set properties of POS devices connected to the DVR.  
A POS device connection requires channel, preset, and Port/Ethernet settings.  
Using the mouse may help make setup easier.  
3. Use the up/down buttons (ꢀꢁ) in <Device> window to  
POS Device  
move to <POS Device>, and press [ENTER] button.  
POS USE  
POS Device Setup  
POS  
CH  
Preset ꢄ  
No preset  
No preset  
No preset  
No preset  
Port/Ethernet  
None  
4. Use direction buttons (ꢀꢁ◄ ►) to move to a desired  
1
2
3
4
None  
None  
None  
None  
None  
item, and set the value.  
None  
None  
POS USE : When selected <POS USE>, DVR and POS will  
be connected.  
If you change settings for the device and press <OK> while  
OK  
Cancel  
J
the <POS USE> is not checked, the changes for POS device  
will not be saved.  
46_ using the DVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4466 4466  
2010-04-30 오후 6:08:3366  

Q See DVR QSD6204 User Guide
Radio Shack PDAs Smartphones 96K User Guide
Regency Indoor Fireplace P33 LP3 User Guide
Renesas Network Card PCA7441 User Guide
Sagem Cell Phone myX3 2 User Guide
Samsung Computer Hardware BN68 01416A 00 User Guide
Samsung DVD Player AK68 01765B User Guide
Sanyo Flat Panel Television DP58D34 User Guide
Sanyo Flat Panel Television DP50719 User Guide
Senco Air Compressor PC2015 User Guide