Samsung DVR SHR 4081N P User Guide
8 Channel DVR  
SHR-4081N/P User’s Manual  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
5
Chapter 5 Menu Setup  
Before Use  
ii  
Safety Regulations  
5-1  
5-2  
iii  
Before we start  
1. System  
5-12  
5-16  
5-18  
5-19  
5-24  
5-26  
5-28  
5-32  
2. Camera  
Standards Approvals  
3. Monitoring  
4. Record Mode  
5. Event Record Mode  
6. Record Schedule  
7. Backup  
1
Chapter 1 Overview  
1. Introduction  
1-1  
1-2  
1-3  
2. Features  
3. Part Names and Functions  
8. Network  
9. Network Setup  
2
Chapter 2 Installation  
6
Chapter 6 PTZ Device Control  
1. PTZ device Control Mode  
2. Basic Operation of PAN, TILT, & ZOOM  
3. PRESET Setup  
2-1  
2-3  
2-4  
1. Installation Environment Setup  
2. Checking Product & Accessories  
3. Additional HDD Installation  
6-1  
6-3  
6-4  
6-6  
6-7  
6-8  
3
Chapter 3 Connecting with Other  
Equipment  
4. Camera Menu Setup  
5. Preset View  
3-1  
3-2  
3-3  
3-5  
3-6  
3-8  
1. Connecting Video, Audio, & Monitor  
6. Other Views  
2. Connecting Network  
7
3. Connecting IEEE1394 Device  
4. Connecting USB Device  
Chapter 7 Recording  
1. PANIC (Emergency Recording)  
2. REC (Normal Recording)  
3. Record Schedule  
7-1  
7-2  
7-3  
7-4  
5. Connecting Alarm Input/Output  
6. Connecting RS-485 Device  
4. Event Recording  
4
Chapter 4 Live  
8
Chapter 8 Search & Play  
Before Use  
4-1  
4-2  
4-5  
1. System Motion  
8-1  
8-2  
8-3  
8-4  
8-5  
8-6  
8-7  
2. Live Screen Mode  
3. Live Channel Selection and Audio On/Off  
Setup  
1. Calendar Search  
2. Event Search  
3. Date/Time Search  
4. Go to First Search  
5. Go to Last Search  
6. Play  
4-6  
4-7  
4-8  
4. Freeze and Zoom  
5. Event Monitoring  
6. Spot-out Monitoring  
iv  
v
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Chapter 9 Backup and Backup Search  
1. Backup  
9-1  
9-4  
2. Backup Search  
10  
10-1  
10-2  
10-3  
10-4  
10-7  
10-8  
10-9  
10-23  
10-30  
Chapter 10 Smart Viewer  
1. Introduction  
2. Feature  
3. PC Specification(Recommendation)  
4. Smart Viewer Installation  
5. Smart Viewer Program Execution  
6. Smart Viewer Initial Screen  
7. Monitoring Mode  
8. Search Mode  
9. SETUP MODE  
11  
11-1  
11-2  
11-3  
11-4  
11-8  
11-9  
11-10  
Chapter 11 Backup Viewer  
1. Introduction  
2. Features  
3. PC Specification(Recommendation)  
4. Backup Viewer Installation  
5. Executing Backup Viewer Program  
6. Initial Screen of Backup Viewer  
7. Using Backup Viewer  
12  
Appendix  
12-1  
12-4  
12-5  
12-6  
12-8  
12-9  
1. Product Specification  
2. HDD Specifications  
3. Outline Drawing  
4. Factory Default  
5. SHR-4081N/P Smart Viewer Play Frame Specification  
6. Troubleshooting(FAQ)  
vi  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1  
Overview  
1
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Introduction  
Features  
1 2  
The Digital Video Recorder(DVR) compresses the camera input data from 8  
channels into a MPEG4 video file and the voice input data into a G.726 audio file  
respectively to record them in the Hard Disk or retrieve them from the Hard Disk  
simultaneously.  
In addition, it transmits the video or audio file out through a network on real time basis  
so that you can monitor either file remotely by your PC.  
■
■
■
8 CH Composite Input Connectors  
NTSC/PAL Video Source Compatible  
Able to record the CIF size (NTSC : 352 x 240 / PAL : 352 x 288) video image at  
the speed of 240ips(NTSC) / 300ips(PAL)  
■
■
■
8 CH Loop Through Video Connectors  
Hard Disk Overwrite Mode  
Large quantity HDD backup function by using IEEE1394 and USB2.0, USB2.0  
Memory, Backup function by using an external CD/DVD writer.  
Able to record, play, and transmit both audio and video files to Windows Network  
Viewer(Smart Viewer) simultaneously  
■
■
■
■
■
■
■
Able to reacord and replay 8 channels of Audio  
Variable Search Mode (Time/Date, Event, Camera)  
Variable Recording Mode (Time Lapse, Event, Schedule, Emergency)  
Extended Hard Disk Connection (IEEE1394, USB2.0)  
Alarm Interface (Input : 8, Output : 4, Reset : 1)  
Remote Monitoring by Windows Network Viewer(Smart Viewer)  
1-1  
1-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Part Names and Functions  
3
No  
Name  
Function  
Video/Audio, set to the system, is recorded to 15  
ips(NTSC)/ 12.5 ips(PAL).  
The image quality of video recording is very high and  
its size is CIF.  
PANIC Button  
7
PANIC  
REC LOCK  
Button  
8
9
Locks the REC key motion.  
Sets up Digital Zoom(x2).  
REC LOCK KEY  
ZOOM Button  
PTZ Button  
ZOOM  
PTZ  
Performs the TELE, WIDE, PRESET, and VIEW func-  
tion by pressing the PTZ button.  
10  
11  
FREEZE  
Name  
No  
Function  
Performs the FREEZE function in the DISPLAY Mode.  
Performs the TELE function by pressing the PTZ.  
FREEZE(TELE)  
Button  
Displays power on/off condition.  
Power LED  
TELE  
ALARM  
Displays both network connection and data transmis-  
sion conditions.  
Cancels the preset ALARM function to set up a new ALARM  
Network LED  
Backup LED  
ALARM(WIDE)  
Button  
12  
13  
14  
function.Performs the WIDE function by pressing the PTZ  
WIDE  
Displays Backup Mode.  
1
SEARCH  
Indicates the Search method.  
Performs the VIEW setup function by pressing the PTZ.  
SEARCH (VIEW  
Button  
)
Indicates Normal Access to HDD.  
HDD Access  
LED  
Upon Access to HDD, LED repeats on and off.  
VIEW  
MENU  
1
8
Displays the system setup menu or enters an upper menu.  
Performs the PRESET setup function by pressing the PTZ.  
MENU(PRESET)  
Button  
Selects Single Channel in the Display Mode.  
2
3
Channel Button  
...  
Used for Number Input Button in the Number Input Mode.  
PRESET  
9
Changes or edits the left setup value for the  
detailed menu item setup.  
Moves the cursor up in a menu or increases the  
setup value for the detailed menu item setup.  
Changes or edits the right setup value for the  
detailed menu item setup.  
Audio Setup  
Button  
¦
Audio On/Off setup during play mode.  
œ
9 Displays Split Screen.  
4 Displays Split Screen.  
‹
Direction  
15  
Moves the cursor down in a menu or decreases  
the setup value for the detailed menu item  
setup.  
6 Displays Split Screen.  
Control Button  
MODE  
ƒ
Split Screen  
Selection  
Button  
7 Displays Split Screen.  
4
Display  
Mode  
8 Displays Split Screen.  
¦
Acts as the Enter key for the menu setup.  
Displays PIP(Picture In Picture)  
Screen.  
Screen change Mode :  
Enters Single Channel Screen  
by the time set in MENU.  
Fast  
Reverse  
16  
17  
18  
Views the fast rewinding search screen.  
Stops file searching.  
STOP  
4 Displays Split Screen.  
Toggles during playback to activate  
PLAY/PAUSE or PLAY.  
PLAY/PAUSE  
Displays the selected channel  
in Full Screen.  
Displays both LIVE Channel and  
Play Channel in PIP Screen  
simultaneously.  
Search  
Function Key  
MODE  
Fast  
Forward  
Mode Selection  
Button  
Views the fast forwarding search screen.  
5
6
19  
Search  
Jog : Used for the Forward/Reverse  
Frame search.  
Shuttle : Performs the Play/Reverse Play  
/FF/REW function.  
9 Displays Split Screen.  
Jog/  
Shuttle  
20  
21  
Recording starts as set in the Normal Record Mode  
while LED is on.  
REC Button  
REC  
JOG  
SHUTTLE  
A port to connect the USB type device.  
USB Port  
1-3  
1-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Caution  
Do not play DVR on the carpet or other soft material to prevent clogging of the air  
ventilator.  
To play DVR on the cabinet or rack, be sure to check the ventilation condition.  
No  
Name  
Function  
Composite Video Signal Input Port (BNC Style  
Connector)  
1
VIDEO IN  
You may use THROUGH port to transmit a video  
signal to the other video equipment.  
THROUGH  
2
3
4
AUDIO IN  
SPOT  
Audio Signal Input Port (RCA Jack)  
SPOT Out Output Port (BNC Style Connector)  
Composite Video Signal Output Port (BNC Style  
Connector)  
5
VIDEO OUT  
Audio Signal Output Port (RCA Jack)  
VGA Video Signal Output Port  
6
7
8
AUDIO OUT  
VGA  
S-VIDEO Video Signal Output Port  
Network Connection Port  
S-VIDEO  
NETWORK  
IEEE1394  
ALARM  
9
10  
11  
IEEE1394 Type Device Connection Port  
- ALARM IN 1~8 : Alarm Input Port  
- ALARM RESET IN : Alarm Reset Port  
- ALARM OUT1~4 : Alarm Output Port  
- TX+, TX-, RX+, RX- : RS-485 Communication  
Port  
12  
13  
AC-IN  
USB  
Supports the AC110-220V(NTSC) power socket.  
A port to connect the USB type device.  
1-5  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2  
Installation  
2
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Installation Environment Setup  
1
Do not play DVR on the carpet or other soft material to prevent clogging of the air  
ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation  
condition.  
<Instructions for the rack mounting of Samsung DVR>  
1. The rack on which the DVR is mounted should not be sealed off.  
2. And it also can allow air circulation through the vent.  
3. As in the figure to the right, we recommend the product should be stacked up with other  
DVRs or rack-mounting devices at a certain space or you install a vent system to  
accommodate airflow.  
4. For forming a natural convection, the air intake hole should be positioned at the bottom and  
the emission at the top.  
You shall pay attention to the following before you use the product.  
1. Do not use it outdoor.  
2. Do not let water or liquid in the connection part or the product itself.  
3. Do not impose excessive shock or force.  
5. We recommend you install each of the air intake and emission holes with a fan motor for  
sufficient airflow.  
4. Do not pull out the power plug unreasonably.  
5. Do not disassemble the product on your own.  
6. Do not exceed the rated input or output range.  
7. Use certified power cord only.  
(The air intake fan should be equipped with a filter to block dust and other impurities from  
inflow.)  
6. The temperature inside the rack and around the DVR should stay between +5°C and +45°C.  
8. Match a product with an input ground with a power cord with a ground.  
Samsung Digital Video Recorder (hereafter “DVR”) is a high-tech security equipment  
that contains a high-capacity HDD and top-notch circuits. High temperature inside or  
outside of the product may cause reduced life and deteriorated performance  
(see graph 1 below), leading to a malfunction. So please follow the instructions below  
to proceed with the installation.  
Temperature  
One Year:24 HR X 365 DAY = 8,760 HR  
(Unit:°C)  
Life (Unit:HOURS)  
<Graph 1 : Correlation between temperature and product life>  
2-1  
2-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4160N/P USER’S MANUAL  
SHR-4081N/P USER’S MANUAL  
Checking Product & Accessories  
Additional HDD Installation  
2 3  
Upon delivery of a product, you shall unwrap the product and put it on the even floor  
or where you want to use it. Then you shall check if the following items are in it.  
You may add up to 3 more HDDs to the product.  
However, since the product contains has many parts which may incur electric shock,  
accident, or product breakdown and improper installation or setup may disturb HDD  
recognition or normal product operation, you shall consult with an expert of the  
agency where you bought the product.  
■ Main Body  
■ User’s Manual  
■ One Power Cord  
■ Two Brackets  
[Caution for HDD Addition]  
- Brackets are used to attach the product to the rack.  
■ Smart Viewer Software CD (Incl. PDF Manual)  
■ 12 Screw Specials  
■ Do not let the cable stuck improperly nor uncoated. (This may cause breakdown or fire.)  
■ Be careful not to cut yourself by sharp edges of the product.  
■ Be careful not to miss the disassembled screws or parts. Imperfect assembly due  
to short of screws or parts may cause breakdown or malfunctioning.  
- Please keep screw specials well to be used for HDD addition.  
■ 2 EA of RS-485/Alarm Terminal Block  
[HDD Addition Procedure]  
1.Loosen screws on both sides(5 points) and back(1 point) to detach the product cover.  
Main Body  
CD  
Bracket  
Power Cord  
RS-485/Alarm  
Terminal Block  
User’s Manual  
Screw  
2-3  
2-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4160N/P USER’S MANUAL  
SHR-4081N/P USER’S MANUAL  
2.Detach the cover from the product. (Pull out the cover slightly and lift from the back  
4.Pull BRACKET-HDD to the product center to detach the fixed part at the bottom to  
side to detach.)  
detach BRACKET-HDD from the product.  
3. A bracket is fixed to each side of HDD. Please loosen the screw of the bracket to  
which you want to fix HDD.  
BRACKET-HDD  
5.Tighten 4 SCREW-SPECIALs(BWH,6-32UNC,L10.5), supplied as an accessory to  
fix HDD to BRACKET-HDD. (Screw tighten force shall be strong enough to resist  
vibration.)  
2-5  
2-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4160N/P USER’S MANUAL  
SHR-4081N/P USER’S MANUAL  
6.Restore HDD installed BRACKET-HDD.  
8.Check the connector, wiring, and cable fixing condition inside the product and close  
the cover.  
(Assembly shall be done in the reverse procedure of disassembly as follows. Align  
the 5 fixing points at the bottom with the BRACKET-HDD fixing holes respectively  
and push BRACKET-HDD out of the product to align the screw fixing holes. Then,  
tighten the screws firmly.)  
9.Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side)  
✻ You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.  
Attention  
For HDD addition, please select the same HDD with the existing HDD fixed to the  
product as far as possible. This product can accept 4 more HDDs, 2 at Primary Slot  
and 2 at Secondary Slot respectively. Both HDDs attached to Primary Slot and  
Secondary Slot shall be set to Master and Slave respectively. Refer to User’s Manual  
for Master or Slave Jumper Setting.  
7.Check if BRACKET-HDD has been fixed to the product and connect both the power  
supply cable and the signal transmission cable (IDE CABLE) to the HDD.  
In the event of only one HDD installation, it shall be inserted into the Primary slot.  
Note  
Refer to Appendix 2 to see which HDD specifications are supplied.  
Power Supply Cable  
Signal Transmission  
Cable (IDE Cable)  
2-7  
2-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4160N/P USER’S MANUAL  
# Please install the fan to be seen from the front view of the set.  
Attention  
! Regarding the sub fan, you need additional brackets and sub fans as follows.  
The sub fan is shaped like this when viewed from the front and back. Please pay  
attention to the fan direction to let wind go through the fan.  
@ Fix the fan as follows.  
$ Fixing the fan to the left.  
2-9  
2-10  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3  
Connecting with Other  
Equipment  
3
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Connecting Video, Audio,  
1 2  
&
Monitor  
Connecting Network  
●
Connecting to Internet through Ethernet(10/100BaseT)  
●
Connecting Internet through ADSL  
3-1  
3-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Connecting IEEE1394 Device  
3
●
Connect the IEEE1394 hard disk through the back port of SHR-4081N/P.  
You can connect up to 6 IEEE1394 armored hard disks by the Daisy-Chain  
method.  
After connection, Menu - System - HDD Setup is necessary for recognition and  
setup for use.  
●
●
Caution  
The IEEE1394 Device hard disk shall be set to Master.  
●
●
It acts as HOT PLUG to connect or disconnect the IEEE1394 device while the  
system is running.  
If you press Connect/Disconnect in Menu - System - HDD Setup, HOT PLUG will  
be recognized or deleted.  
Note  
Note  
See 5-8 System (HDD Setup) of User’s Manual.  
Refer to Appendix 2 to see which HDD specifications are supplied.  
Caution  
-
Wait until the HOT PLUG connected hard disk is stabilized enough (approx. 2 seconds  
per each hard disk) and click CONNECT in SHR-4081N/P MENU before use.  
- Be sure to click DISCONNECT in SHR-4081N/P MENU to delete IEEE1394 Device  
safely. Failure of clicking DISCONNECT may cause improper operation of IEEE1394  
Device.  
3-3  
3-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Connecting USB Device  
Connecting Alarm Input/Output  
4 5  
1. A total of 2 USB connecting terminals are placed in front of and behind SHR4081N/P each.  
2. Connect USB HDD, USB CD/DVD, and USB Memory through the ports in front and  
behind SHR-4081N/P respectively.  
3. Only one USB device can be assigned to each USB connection port.  
4. To recognize/ignore USB HDD, follow the procedure of Menu - System - HDD  
Setup upon connecting.  
5. Supply the HOT PLUG function to connect/disconnect the USB device.  
6. To recognize/ignore the HOT PLUG function, press Connect/Disconnect from Menu  
- System - HDD Setup.  
The Alarm IN/OUT port in the back of SHR-4081N/P is composed of the following  
elements.  
Note  
Refer to User’s Manual 5-8, SYSTEM(HDD Setup).  
●
ALARM IN/OUT Connection  
Caution  
Name  
- ALARM IN1  
- ALARM IN2  
- ALARM IN3  
- ALARM IN4  
- ALARM IN5  
- ALARM IN6  
- ALARM IN7  
- ALARM IN8  
Function  
- After enough time is given to the stabilization of the USB device connected by  
HOT PLUG, press Connect from SHR-4081N/P Menu.  
- To disconnect the USB device, be sure to click Disconnect from SHR-4081N/P  
Menu. Otherwise, the USB device may be in trouble.  
- Available to use with connecting the same kinds of USB device to the USB terminal  
on the front and back of SHR-4081N/P. (For example, 2 CD-RW or 2 USB  
memories can be connected to thefront and back of SHR-4081N/P.)  
- If the USB memory is used, it should be set to the format supported by  
SHR-4081N/P. Although it is formatted with FAT32 in the PC, it is re-formatted  
when it is connected to SHR-4081N/P.  
1
ALARM Input Port  
On receiving an ALARM RESET signal, the  
2
3
- ALARM RESET IN system cancels the current ALARM input or  
output signal and resumes sensing.  
- ALARM OUT1  
- ALARM OUT2  
Caution  
ALARM Output Port  
- ALARM OUT3  
- ALARM OUT4  
- The USB device HDD shall be set to Master.  
3-5  
3-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Connecting RS-485 Device  
6
●
ALARM IN/OUT Connection  
●
Connect RS-485 Device through the back port of SHR-4081N/P.  
●
You can install and control the PTZ device supporting RS-485 communication.  
●
You can adopt either Half Duplex or Full Duplex method for the connection.  
PTZ device  
SHR-4081N/P  
Rear  
Half Duplex Type  
Data (–)  
Tx(–)  
Tx(+)  
Data (+)  
Full Duplex Type  
Rx(+)  
Rx(–)  
Rx(–)  
Rx(+)  
Tx(–)  
Tx(+)  
●
Baud Rate covers 600, 1200, 2400, 4800, 9600, 19200, and 38400.  
Caution  
Check if RS-485 Device is compatible with SHR-4081N/P first. Then pay attention to  
the polarity of RS-485 which has two poles, + and -.  
3-7  
3-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4  
Live  
4
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
System Motion  
Live screen Mode  
1 2  
●
Turn the power on and the following LOGO screen pops up.  
Definition of Live Screen Icon  
The Live screen icons of SHR-4081N/P display the current setup and function status of each screen.  
PTZ  
N
V.Loss  
CAM_01  
CAM_01  
●
●
●
After the LOGO screen appears, the button in front of SHR-4081N/P blinks 6 times  
to initialize the system for operation.  
: Recording Icon  
Each icon represents Normal / Panic / Event(Alarm+Motion) /  
Schedule Recording.  
P
E
S
When the initialization is complete, the live video appears along with a beep  
sound.  
: Recording Video Size Icon  
Each icon represents the recording size of Large/ Normal/ CIF  
Large : Full D1(NTSC : 720 x 480 / PAL : 720 x 576)  
Normal : Half D1(NTSC : 720 x 240 / PAL : 720 x 288)  
CIF : CIF(NTSC : 352 x 240 / PAL : 352 x 288)  
It requires 30 to 40 seconds until the Live screen appears.  
Note  
PTZ  
: PTZ Icon  
This icon appears when you set up PTZ device with the PTZ icon and  
turns yellow when you execute PTZ.  
A new HDD may require more time for the initialization until the Live screen  
appears due to the initialization period of the new HDD.  
: Audio Icon  
If the Live screen does not appear at all or the button in front of SHR-4081N/P  
repeats blinking, please check the connection across the product body. If you find  
any error, please ask the shop where you bought the product.  
This icon represents Audio On/Off status and turns yellow for On.  
It does not appear for Video or Audio Disable.  
: Sensor In Event Icon  
This icon appears in the channel synchronized with the external sensor signal  
input with Sensor On.  
●
The Live screen does not affect the earlier MENU setup. If you reboot the system  
after power-off during recording, the Live screen will appear, accompanying  
recording.  
: Motion Event Icon  
This icon appears in the Motion Event channel with Motion Detection On.  
: Zoom Icon  
Note  
This icon appears with Zoom On or Zoom In and disappears when you cancel  
Zoom On.  
If you see no more Live screen, you shall check if video data comes out in Composite  
mode or VGA mode.  
If you whish to change the video output mode, you shall hold on to the MODE  
button in front of SHR-4081N/P and keep pressing the 0 button for 5 seconds. Press  
‘0’ button for 5 seconds with pressing the front mode button to change video output  
mode. After 3 times flickering of PTZ LED on the front left, it reboots.  
: Freeze Icon  
This icon appears in the Freeze mode and disappears when you cancel  
Freeze.  
: Insufficient Disk Space Icon in CH  
More than one channel has insufficient recording space.  
: Insufficient Disk Space Icon in all CHs  
All the channels have insufficient recording space.  
4-1  
4-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Selecting Live Screen Mode  
: Screen change Icon  
This icon appears in the Screen change mode.  
: Backup playback icon  
It is displayed when the backup data plays.  
: Fan fail Icon  
Each mode may be selected by [MODE Button] and [CH1 ~ CH8 Button]  
The following figure shows Live Mode of SHR-4081N/P after converted.  
It is displayed when the fan stops.  
: It is displayed when there is no HDD.  
V.Loss / V.Off : Video Input Status  
If there is no more video data input with Video On, [V.Loss] appears in the channel.  
If you set Video On/Off to Off, [V.Off] will appear.  
Definition of Live Screen Mode  
SHR-4081N/P receives 8 live images and displays them in the following 8 modes.  
CAM_02  
CAM_01  
CAM_02  
CAM_01  
CAM_02  
CAM_01  
CAM_04  
CAM_03  
CAM_06  
CAM_04 CAM_05  
CAM_06 CAM_07  
CAM_03  
CAM_05  
CAM_01  
CAM_04  
CAM_03  
4 Split Mode  
6 Split Mode  
7 Split Mode  
Single Mode  
CAM_02  
CAM_01  
CAM_02  
CAM_05  
CAM_08  
CAM_03  
CAM_03  
●
●
●
The default is 9 Split Screen Mode.  
CAM_04  
CAM_07  
CAM_06  
CAM_04  
CAM_08  
CAM_01  
CAM_02  
CAM_01  
CAM_01  
CAM_05 CAM_06 CAM_07  
[1 CH ~ 8 CH] are displayed in the 9 split mode.  
8 Split Mode  
PIP Mode  
Screen change Mode  
9 Split Mode  
Whenever the LEFT/RIGHT button is pressed, [4 Split 1 . 4 Split 2 .] in order in the  
4 split mode.  
●
●
Full Screen(Single) Mode:  
Displays the selected channel in a full screen. Then, the channel LED concerned  
will be turned on.  
●
Other modes than Full Screen may be selected by pressing the [Mode] button and  
➝
[
, ➝] button in sequence.  
4,6,7,8 Split Mode:  
Every time you press the [Mode] button, the mode changes in the following  
procedure, [16Split] ➝ [9Split 1] ➝ [4Split 1] ➝ [6Split] ➝ [7Split] ➝ [8Split] ➝  
Displays 4, 6, 7, 8, and image channels in the respective split screen and the CH  
LED lights on to indicate the channel no. You may match channel numbers with  
split screens on your own.  
[PIP] ➝ [Screen Mode] ➝ [16Split].  
➝
Every time you press the [ , ➝] button, the mode changes in the following  
The 4CH Split mode has the function of screen change. Refer to (4-4) Live Screen  
Mode Setup. Press the [Direction Control] button in the 8CH Split mode and the  
main screen(CAM_01 in the figure) will move.  
procedure, [9Split 1, 2, Screen Mode], [4Split 1, 2, 3, 4, Screen Mode].  
Press the [CH1~CH8] button to see the full screen of each channel.  
●
●
●
●
PIP(Picture in picture) Mode:  
Press the Mode button after you convert to a full screen in the Split Screen mode  
to returns to the previous Split mode screen.  
Displays a one-ninth sized screen in the full screen and the channel LED  
concerned is turned on. You are able to choose a channel as you want to, which is  
displayed in the full screen or reduced screen area. You may move the PIP screen  
at 5 stages in the Full screen with the œ or ƒkey.  
Screen change Mode:  
Displays the time when FULL SCREEN has been set to each channel in sequence  
and the channel LED concerned is turned on.  
4-3  
4-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Freeze and Zoom  
Live Channel Selection and Audio On/Off Setup  
4
3
In other split modes than Full Screen Mode, 9 Split Mode, and Screen change Mode,  
you may choose a channel to be displayed in each split area on your own. Meanwhile,  
the channel whose MENU is set to Audio On can set up Audio On/Off in all Live Modes.  
Freeze Function  
Freeze pauses the video image in Live Screen, only available in Live Mode. You can set  
up Freeze On/Off with [FREEZE] button and [FREEZE LED] is turned on or off  
depending on the Freeze On/Off setup condition.  
Selecting Audio On/Off from the Full Screen mode  
In the Full Screen mode, the selected CH Audio is automatically turned on and you  
can toggle the CH button to turn Audio on/off. The Audio icon turns yellow/white  
depending on Audio On or Off.  
Zoom Function  
Zoom enlarges the selected area twice, only available in Full Screen Mode.  
If you press [ZOOM] button in Full Screen Mode, the zoomed area will appear now you  
are able to adjust the selected area position. If you select an area and press [ENTER]  
button, the area will be displayed in double size. If you press [ENTER] button again, the  
previous screen to select Zoom area will appear again and you will be capable of Zoom  
Off with [ZOOM] button after the screen is enlarged. Depending on the Zoom On/Off  
setup condition [ZOOM LED] is turned on or off.  
9 Selecting Audio On/Off in the Split mode  
9 If you press [Enter] in the Split mode, the following cursor will appear and the  
channel will be selected. Press the CH button with a channel selected to set Audio  
on/off. Now, the Audio icon turns yellow/white depending on Audio On or Off.  
16 You may not choose a channel in the Split mode on your own.  
CAM_02  
CAM_03  
CAM_06  
CAM_01  
CAM_04  
CAM_07  
CAM_05  
CAM_08  
CH Selection and Audio On/Off Setup in the 4, 6, 7, 8 Split  
mode and PIP mode  
As in the 9 Split mode, if you press [Enter] in the 4,6,7,8 Split mode and PIP mode, the  
selected cursor will appear and the channel will be selected.  
With a channel selected, press [CH1 ~ CH9] to select the channel in the screen. As in  
the 9 Split mode, use the CH button LED to make Audio on/off setup. Now, the Audio  
icon turns yellow/white depending on Audio On or Off.  
4-5  
4-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Spot-out Monitoring  
Event Monitoring  
6
5
Spot-out Monitoring has nothing to do with Live Screen Output, monitoring the full  
screen of a certain channel. If you select Monitoring in the MENU screen, you can  
make a channel among CH1 to CH8 spot out or you can output channels one by one  
at an interval as Screen change Mode of Live Mode. The interval is as same as the  
forwarding time of Screen change Mode of Live Mode. If you set Spot-out Event  
Monitoring to On, you will be able to spot out the event channel. In case of  
simultaneous event occurrence at more than one channel, the lowest numbered event  
channel has the first priority to be spotted out.  
Event Monitoring displays the channel synchronized with a specific event  
(Sensor/Motion/Video Loss) on the screen when it occurs. Event Monitoring On/Off  
and Event Duration setup is available in [Menu]➝[Monitoring].  
If you set the Event Monitoring interval to 5 seconds and an event occurs at CH2 in  
the beginning as in the following figure, the system will display CH2 in the whole  
screen for 5 second. Another event within 5 seconds will be displayed together with  
the existing event. In the following figure, both CH1 and CH3 events occur within 5  
seconds (for example, in 4 seconds) after the CH2 event, the three events are split  
into 4 screens.  
Caution  
Likewise, CH2, CH5, and CH7 events within 5 seconds after both CH1 and CH3  
events are integrated with the existing 2 events and all the 5 events are split into 9  
screens. Without further event during Event Duration, the system will return to the  
previous Live Mode.  
If the built-in HDD is not connected, or it operates with power applying in error,  
) indicating "built-in HDD error" is displayed at the top of left.  
At this time,  
(
(1) Live screen mode  
(2) Monitoring mode by Smart Viewer  
If you press [ALARM] button during Event Duration, Event Monitoring will stop.  
On sensing an event, [ALARM LED] is turned on. If you press [ALARM] button now,  
[ALARM LED] will go out.  
operate only and the other functions including recording, search, playback, menu  
setup, and PTZ do not operate.  
If the above problem is occurred, Be sure to contact a service center to settle the  
problem.  
Press [ALARM] to reset the Alarm setting. The Event icon will disappear and this  
function will be cancelled during Event monitoring. When the Event recording time,  
Pre-Alarm time, and Post-Alarm time were already set after an alarm had been given,  
Event recording will be done for the set period.  
Caution  
If the fan of set is not operated or occurs an error, the following error message is  
popped up in the live screen. And the fan error icon is displayed at the left upper.  
Check the fan of set in this time. The left upper icon is disappeared automatically if  
the fan operates normally.  
Fan Information  
Fan is in trouble.  
Refer to the Manual.  
4-7  
4-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5  
Menu Setup  
5
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Before Use  
System  
1
●
Selection  
●
System Menu has the following items in detail.  
The yellow cursor shows the current window.  
Use the œ,ƒ,¦, ‹ button in the front to move the cursor on your desirous menu.  
If you press the “Enter” key with the cursor clicking on your desirable menu, the  
system will enter the new mode.  
Press the “Enter” key to finish selection.  
On seeing Drop Down Menu, use the œ or ƒ button to move the cursor on your  
desirable menu.  
●
●
“OK” or “Cancel” in Menu Setup Window  
Once changed, the new menu setup procedure will be finalized by pressing “OK”.  
Pressing “Cancel” will cancel the previous setup and return to the upper menu.  
Front “MENU” and “SEARCH” Button  
The MENU button or SEARCH button, if pressed first, acts as an entrance button.  
Once entering, it reverses the page to the previous one.  
Date/Time/Language Setup  
●
●
The “>” or “V” mark beside the title copies the line in the arrow direction to the  
value of the first line.  
The first page of the menu is structured as follows.  
●
●
Date  
Press the “Enter” button and the ¦ or ‹ button to move to Y/M/D.  
Use the œ or ƒ button to change the date.  
Press the “Enter” button to come out of the mode.  
Time  
Press the “Enter” button and the ¦ or ‹ button to move to H/M/S.  
Use the œ or ƒ button to change the time.  
Press the “Enter” button to come out of the mode. Once changed, the date and  
time will remain unchanged until you press “OK” or “Cancel”.  
5-1  
5-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Password  
Note  
[Date/Time Change]  
Pressing “OK” after you change date and time, you will be asked by a pop-up  
window if you really confirm the change. Here, press “Yes” to change the time.  
Since Date/Time does not change in backup process, be sure to stop the  
backup process before you change Date/Time.  
Caution  
[Date/Time Change]  
If you restore Date/Time to the original value, the data recorded before the  
restoration may be deleted. For example, if you restore 8 am to 7 am, all the data  
recorded between the times will be deleted.  
●
●
The Default Password is 4321.  
New Password  
●
●
●
Date Format  
This is used to change the system password inside SHR-4081N/P. You are  
allowed to create a password up to 8 digits. Press the “Enter” button and then a  
channel button from 0 ~ 9 on your left to finish input. If you press the “Enter”  
button after change, the system will automatically turn to “New Password Confirm”.  
This supplies 3 formats, Year-Month-Date / Date-Month-Year / Month-Date-Year.  
Time Format  
This supplies 2 formats, 24 Hour / 12 Hour(AM/PM).  
●
●
●
New Password Confirm  
Language  
This confirms a new password. You shall be obliged to input New Password in the  
above row first. Without New Password input, New Password Confirm input has no  
effect.  
After you select a language, OSD is expressed in the selected language.  
The available languages are added in the list.  
●
DST(Daylight Saving Time)  
Password Lock  
DST sets the watch one hour faster than the local standard time.  
This makes the system count for DST in DST regions.  
Being the DST setup date, the set goes one hour faster and starts rebooting.  
Pressing the “Menu” button while it is set to On, you will be asked by a pop-up  
window of the password. Pressing the “Menu” button while it is set to Off, you will  
enter Menu Mode immediately, not being asked of the password.  
Set to Off, DST does not operate. Then, you are unable to enter the right date  
menu. Set to On, you can set the start time on the left and the end time on the  
right on the basis of ‘~’. DST is allowed to set Month/Date/Time only.  
Year/Minute/Second remains inactivated.  
All Key Lock On  
If you select this, the system will enter Live Mode immediately. If you press a  
button in the front, the Password window will pop up. Succeeding in Password  
input will be followed by Key Lock cancellation after such a message window pops up.  
Note  
Note  
[When the DST is operated]  
The proceeding backup is cancelled. Recording in progress will be suspended for a  
moment until rebooting.  
[All Key Lock On]  
If you select this, the system will enter Live Mode immediately and keys will be  
locked.  
Caution  
[When the DST is operated]  
As the system goes one hour earlier, the data recorded since an hour ago will be  
deleted. As DST activates at the preset time, you are recommended to take the  
utmost care of preventing any trouble incurred by data deletion or rebooting.  
5-3  
5-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
System Log List  
Load Factory Default  
Panic Record End  
System Start  
Viewer Login (Admin) Time Change  
Panic Recording End  
Date/Time Change  
System Start  
Login(Admin)  
Logout(Admin)  
Login(User)  
Viewer Logout (Admin) Load Factory Default System Initialization  
Viewer Login (User)  
System Upgrade  
System S/W Change  
No Space for HDD  
Backup Start  
Logout(User)  
Viewer Logout (User) Disk Full  
Setup Start (Local)  
Setup End (Local)  
Setup (Remote)  
Play Back Start  
Play Back End  
Record Start CH[N]  
Record End CH[N]  
Set: Menu Entering  
Set: Menu Escape  
Viewer:Menu Setup  
Play Start  
Backup Start  
Backup End  
Backup Stop  
Backup Fail  
Backup End  
Backup Stop  
Backup Failure  
Play End  
ATA HDD Erase  
ATA HDD Data Deleted  
Channel [N] Play Start IEEE1394 HDD Erase IEEE1394 HDD Data Deleted  
●
This initializes all the menu preset values.  
The recorded data will not be deleted. Press “OK” in the confirmation window to  
start initializing.  
Channel [N] Play End USB HDD Erase  
USB HDD Data Deleted  
Replay stop due to overwriting  
Backup stop due to overwriting  
Power Failure Recovery System Restoration after Power Failure Overwrite Playback Stop  
Panic Record Start  
Backup Stop(Overwrite)  
Panic Recording Start  
Event Log  
System Log  
●
●
●
●
●
●
Checks the record regarding Event like Alarm / Motion / Video Loss  
This displays the contents of a log regarding Event its execution date/time.  
First : Returns to the first page.  
Prev : Back to the previous page.  
Next : Forwards to the next page.  
Last : Moves to the recent.  
●
Event Log List  
●
●
System Log is used by a controller to check crucial records.  
Video Loss CH[N]  
Channel N Video loss  
Channel N Alarming  
This displays such contents of a system related log and its execution date/time as  
System Start, System Termination, and Menu Setup Change.  
Alarm Detection CH[N]  
Motion Detection CH[N]  
Sensing Channel N Motion  
●
●
●
●
First : Returns to the first page.  
Prev : Back to the previous page.  
Next : Forwards to the next page.  
Last : Moves to the recent.  
5-5  
5-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
System Information and Setup  
Caution  
[HDD Erase]  
Data will not be deleted in backup or recording process.  
Please be sure to suspend backup or recording before you delete any data.  
If the recording is in progress, stop the recording to delete a data.  
[USB S/W Upgrade]  
You may download the software for upgrade from CCTV Part of http://www.samsung.com.  
If the USB memory to be upgraded is not in a format supported by the DVR set, the upgrade  
cannot be done. In this case, please use “Remove Devices” from “System Information and  
Settings” in Menu 5-7. There should be only one file for upgrade in the USB memory.  
●
●
●
Software Version : Displays the current version. Setup is not available.  
Broadcast Format : Displays the current Format(NTSC/PAL). Setup is not available.  
Mac Address : 6 Byte hardware address. Setup is not available.  
HDD/External Device Setup  
●
Device Erase  
Erases the data in the ATA / IEEE1394 / USB / USB memory.  
Check the box that you want to delete and press “OK”.  
Data is undeletable during Backup.  
●
USB S/W Upgrade  
When there is no device, USB S/W Upgrade is failed.  
Note 1  
Being a physical hard disk inside the SHR-4081N/P main body connected by an IDE cable, this  
stores data.  
●
●
HDD Information  
[External HDD]  
Being a physical hard disk connected with the port and terminal in the back of the  
SHR-4081N/P main body, this stores data.  
Displays the number, quantity, and status of ATA, IEEE1394, and USB.  
Setup is not available.  
This can be used as Extended HDD or Backup HDD.  
- Extended HDD : Supplements Internal HDD quantity. Connected, it takes the place of Internal  
HDD.  
Status : Internal HDD, External HDD, Backup HDD  
External HDD setup  
1. Backup/External  
- Backup HDD : Backs up the data recorded in the set.  
You are able to determine the usage of IEEE1394 and USB.  
Not Defined ➝ When the connected HDD usage is not defined.  
Expressed in External or Backup.  
No Device ➝ When no HDD is connected. You are able to press right TAB after you  
connect HDD.  
External ➝ When the connected HDD is set to External. It may used as a back  
up HDD if you press the “Enter” button and turn to Backup.  
Backup ➝ When the connected HDD is set to Backup. It may used as an  
External HDD if you press the “Enter” button and turn to External.  
Note 2  
[ATA]  
Usage : Internal HDD  
This is a physical hard disk connected with SHR-4081N/P through the IDE cable.  
[USB]  
Usage : External HDD (Extended HDD or Backup HDD)  
A physical hard disk connected with the USB port in the back of the SHR-4081N/P main body  
[IEEE1394]  
Usage : External HDD (Extended HDD or Backup HDD)  
A physical hard disk connected with the IEEE1394 port in the back of the SHR-4081N/P main  
body  
2. Hot Plug - Connect/Disconnect  
You may connect or disconnect IEEE1394 Hard Disk while power is supplied to the  
SHR-4081N/P main body.  
① As for connecting, connect IEEE1394 Hard Disk with the SHR-4081N/P main  
body and press “Connect”. Pressing “Connect” makes the SHR-4081N/P  
main body recognize all connected IEEE1394 Hard Disks.  
➁ As for disconnecting, be sure to press “Disconnect” and detach IEEE1394  
Hard Disk from the SHR-4081N/P main body safely.(Be sure to pause recording  
or backup process.) Pressing “Disconnect” cancels and detaches all connected  
IEEE1394 Hard Disk.  
Note 3  
[USB S/W upgrade]  
1. You can download the data(tgz file) for upgrade from www.samsung.com, CCTV Part.  
2. The USB memory should have only one tgz file for upgrade.  
3. In case of other memory format than supported by SHR-4081 model, please delete the  
memory and set it up according to the set format.  
5-7  
5-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Caution  
Caution  
[Disk End Mode Overwrite]  
In the Overwrite mode, delete the old Event data in advance.  
[ IEEE-1394 Hot-Plug Connect/Disconnect Function ]  
Both IEEE1394 and USB support Hot-Plug.  
[Backup HDD]  
You may set both the USB and IEEE1394 device as the Backup HDD.  
Remote control Device  
●
MENU for Samsung Integrated Remote Control(SSC-2000)  
HDD Mode Setup  
●
●
Device  
A Remote Control Device, being connected to the RS485 port.  
ID  
Unique ID of SHR-4081N/P  
This unique ID is essential as SSC-2000 can control multi SHR-4081N/P DVRs.  
●
Baudrate  
Baudrate to communicate with SSC-2000  
Be sure to be identical to SSC-2000 Baudrate for communication.  
●
●
Disk End Mode  
Stop : Stops recording when HDD is full during recording.  
Overwrite : Deletes the original data and save a new data when HDD is full  
during recording.  
●
●
●
●
Parity  
Sets up one of None / Even / Odd.  
Disk End Beep  
On : Beeps when HDD is full during recording.  
Off : When HDD is full, the beep sound is not heard.  
Date  
Sets up either 7 or 8.  
Stop  
Sets up either 1 or 2.  
Duplex  
Sets up either Half Duplex or Full Duplex.  
Note  
If you select Remote Control Device, you may not PTZ device with SHR-4081N/P.  
The PTZ button in front of SHR-4081N/P becomes inactivated.  
Press the PTZ button and the PTZ ban icon(  
) will appear.  
It’s because the RS-485 port setup was done for Romote Control Device.  
5-9  
5-10  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Camera  
2
●
The detailed Camera Menu items are as follows.  
System Shutdown  
●
Terminates the work in action safely and turns the power off.  
Press “OK” in the confirmation window and plug out when you see “Safe to Power  
Off”.  
Camera Configuration  
Caution  
[System Shutdown]  
Power-off without terminating the system in the System Shutdown menu may incur  
improper motion like data loss and disk failure. Power-off shall be done in the  
System Shutdown menu.  
●
Video  
On : Camera images from a selected channel appear.  
Off : Camera images from a selected channel disappear.  
Covert1 : Displays other information than the image information on the selected channel.  
Covert2 : Hides all the information on the selected channel.  
In this case, you are not allowed to set Audio/Title/Screen change.  
●
Audio  
On : You can hear voices from a selected channel.  
Off : You cannot hear voices from a selected channel.  
5-11  
5-12  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Title  
PTZ Device  
You can name the camera of a selected channel.  
If you press the [Enter] button, the Virtual keyboard will come out.  
‹¤Virtual Keyboard  
If you move the cursor, you can type text by text.  
Up to 15 texts can be typed.  
Keyboard cannot be composed of all spaces.  
Pressing Caps Lock changes the keyboard that can be selected. (2 Modes)  
●
●
ID  
PTZ device ID from 0 to 255  
Protocol  
A protocol supported by PTZ device  
The following protocols are now being supported.  
Samsung / Vic. / Pan. / AD / Phi. / Ern. / Pel-D / Pel-P / Vcl. / Dia. / Kal.  
●
Auto Seq.  
●
Baudrate  
You may define the duration of each channel at the Screen change channel in Live  
Mode. A channel, set of Off, does not operate in Screen change Mode.  
Baudrate supported by PTZ device , 600 / 1200 / 2400 / 4800 / 9600 / 19200 /  
38400  
●
●
●
●
Parity  
Defines one among None, Even, and Odd.  
Data  
Defines either 7 or 8.  
Stop  
Defines either 1 or 2.  
Serial Mode  
Defines either Half Duplex or Full Duplex.  
Caution  
The above items shall be aligned with the PTZ device setup condition.  
For the details, please refer to User’s Manual of the PTZ device manufacturer.  
5-13  
5-14  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Monitoring  
3
Screen Setup  
●
Event Monitoring  
You are able to set to Off / 3sec / 5sec / 10sec / 20sec / 30sec / Continuous.  
① Off : Event Monitoring does not operate to turn to the screen where an event  
occurs.  
●
This is a window to adjust Brightness/Contrast/Color for the camera image of each  
channel. Put the cursor on the channel that you want to adjust and set up  
Brightness/Contrast/Color. Once selected, the channel appear in the PIP area on  
the right. Press the œ or ƒ button to adjust the value from 0 to 100.  
➁ 3sec / 5sec / 10sec / 20sec / 30sec : For the period, the screen is seen before  
the next screen appears.  
➂ Continuous : The Event Monitoring screen remains alive until you press the front  
“Alarm” button to cancel the screen manually.  
●
●
If you select CH ✓, all the channel values will become the same as the finally  
●
OSG Display  
selected channel value.  
① Date : The date is displayed on the screen or not depending Date remains On or Off.  
➁ Time : The time is displayed on the screen or not depending Time remains On or Off.  
“Default” resets the current channel to the basis value of 50.  
➂ Title : The title is displayed on the screen or not depending Title remains On or Off.  
➃ Status : Audio/Ptz is displayed on the screen or not depending Status remains  
On or Off.  
●
Spot Out Channel  
Spot Out channel is used to let one of two monitors monitor a channel, focusing on  
it. Spot Out channel supplies two functions, continuous monitoring of only one  
channel and Screen change to display all the channels one by one.  
① Screen change setup ranges from CH1 to CH8.  
➁ Set to Screen change, Spot Out channels are displayed in turn.  
➂ Screen change Duration is as same as determined for Camera Configuration.  
●
Spot Out Event Monitor  
Determines if event monitoring will be executed for Spot Out channels.  
① Off : dose not event monitoring in Spot out channel.  
➁ 3sec / 5sec / 10sec / 20sec / 30sec : Duration options on the screen before it  
scrolls down.  
➂ Continuous : Once scrolled down, the screen remains displayed until you delete  
“Alarm” LED in front manually.  
5-15  
5-16  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Record Mode  
4
NTSC  
PAL  
●
Monitor Out  
You may not use both VGA Output and Composite/S-Video Output at the same time.  
Accordingly, the user shall choose either one.  
① Composite : The output will come out from the  
“Composite / S-Video Output” port.  
➁ VGA : Output comes out of the “VGA Out” port.  
Any change from Composite to VGA or vice versa reboots the system  
automatically.  
●
PB( Playback ) Channel Position  
Designates the position of a channel to be played back in Play Back 9 Split Mode.  
Right Down : Designates a location on the bottom right corner.  
Center : Designates a location in the center.  
If you press the front “REC” button, the mode to be recorded will be determined.  
☛ For Event Recording Mode value setup, refer to 5-19. Event Record  
Mode Setup Menu.  
●
Mode  
●
Multi-channel Seq.  
The change of split screen is available to be set.  
It can be set to Off ,3 Sec,5 Sec, 10 Sec, 20 Sec, 30 Sec.  
On : Pressing the REC button starts recording the current channel.  
Off : Even pressing the REC button does not affect current channel recording.  
The default is set to “On”.  
●
Video Size  
Determines the size of a screen to be recorded.  
Full D1 : 720 x 480(NTSC) / 720 x 576(PAL) ➝ Large(L)  
Half D1 : 720 x 240(NTSC) / 720 x 288(PAL) ➝ Normal(N)  
CIF : 352 x 240(NTSC) / 352 x 288(PAL) ➝ CIF(C)  
Caution  
[Monitor Out]  
Note  
[Video Output]  
Set to Composite Output, VGA does not come out.  
Set to VGA, Composite Output does not come out.  
If you hold on to the MODE button in Live Mode and keep pressing the 0 button for  
5 seconds, the status will change from VGA to COMPOSITE or vice versa  
accompanying rebooting.  
"Full D1" setup for the resolution is available from the recording sheet number of  
7.5ips(NTSC)/6.25ips(PAL)  
"Half D1" setup for the resolution is available from the recording sheet number of  
15ips(NTSC)/12.5ips(PAL)  
Resolution “CIF” can be set from Recording page number “30.”  
●
●
Recording Resolution  
Selects the recording resolution. VH(Very High) / H(High) / S(Standard) / L(Low).  
Rate  
Determines Frame Rate to be recorded. Frame Rate means the number of screen  
recorded every second.  
Set to 30ips(NTSC)/25ips(PAL), the system records too many screens per  
second and play continues intermittently since recording is more detailed.  
This is appropriate for concentrated monitoring zone setup.  
Set to the one of 30ips / 15ips / 10ips / 7.5ips / 5ips / 3ips / 1ips (NTSC)  
Set to the one of 25ips / 12.5ips / 8.33ips / 6.25ips / 5ips / 2.5ips / 1ips (PAL)  
Auto Deletion  
●
Click [Off] button at the left bottom to select Off/On.  
Select On to limit the search date by moving to the date selecting button.  
Select Off not to limit the search date.  
The date is limited from 1 to 99.  
5-17  
5-18  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Event Record Mode  
5
●
The detailed items of Event Record Menu are as follows.  
●
Quality  
Recording resolution will be determined.  
VH(Very High) / H(High) / S(Standard) / L(Low).  
Note  
"Full D1" setup for the resolution is available from the recording sheet number of  
7.5ips(NTSC)/6.25ips(PAL)  
"Half D1" setup for the resolution is available from the recording sheet number of  
15ips(NTSC)/12.5ips(PAL)  
Resolution “CIF” can be set from Recording page number “30.”  
Evnet Record Mode  
●
Rate  
NTSC  
Determines Frame Rate to be recorded. Frame Rate means the number of screen  
recorded every second.  
Set to 30ips(NTSC)/25ips(PAL), the system records too many screens per second  
and play continues intermittently since recording is more detailed. This is appropri-  
ate for concentrated monitoring zone setup.  
Set to the one of 30ips / 15ips / 10ips / 7.5ips / 5ips / 3ips / 1ips(NTSC)  
Set to the one of 25ips / 12.5ips / 8.33ips / 6.25ips / 5ips / 2.5 ips / 1ips(PAL)  
●
Pre-Event (PreEve.)  
PAL  
Pre-Event Section  
Event occurred point of time  
Records the situation until Event is issued.  
Off : No recording  
5sec / 10sec / 20sec / 30sec : The recording time options before Alarm issue  
●
Post-Event (PostEve.)  
Determines a mode to be recorded when an event occurs.  
Post-Event Section  
Event occurred point of time  
●
V. Size (Video Size )  
Determines the size of a screen to be recorded.  
Full D1 : 720 x 480(NTSC) / 720 x 576(PAL) ➝ Large(L)  
Half D1 : 720 x 240(NTSC) / 720 x 288(PAL) ➝ Normal(N)  
CIF : 352 x 240(NTSC) / 352 x 288(PAL) ➝ CIF(C)  
Records the situation since Event is issued.  
Off : No recording  
5sec / 10sec / 20sec / 30sec / 1min / 3min / 5min / 10min / 20min :  
To this, the recording time after Alarm issue is set.  
5-19  
5-20  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Alarm Detection Setup  
Motion Detection Setup  
●
Sensor State  
Off : Sensor does not operate.  
① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed,  
an alarm will be issued. (A Contact)  
➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open,  
an alarm will be issued. ( B Contact)  
●
Cam  
Determines a camera which will synchronize with the current sensor.  
The default is currently set to the sensor number. A sensor shall be synchronized  
with at least a camera. Multi-synchronization is possible.  
●
●
M.D State  
Off : Motion Detection does not operate  
On : Motion Detection starts operation.  
Area  
Select the Motion Detection zone. It is composed of 45x40(NTSC) / 45x48(PAL)  
sized Block. You are forbidden to determine 4 block rows(Up/Down/Left/Right) to  
allow them to be  
displayed in all monitors.  
‹ Select All : Selects the whole area.  
‹ Select One : Selects a block every time. Selection is done by a toggle system.  
‹ Select Quarter : Split the whole area into 4 pieces, which enables selecting a  
fourth of the whole area.  
●
Alarm-Out  
Arranges Alarm-Out when Alarm Sensor sounds.  
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to  
synchronize with the current sensor. Multi-choice is possible.  
‹ Clear All : Cancels the whole area.  
‹ Save & Exit : Saves and exits.  
‹ Exit : Exits without saving.  
●
Duration  
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.  
Off / 3sec / 5sec / 10sec / 20sec / 30sec  
5-21  
5-22  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Record Schedule  
6
●
●
Sensitivity  
Determines Motion sensing sensitivity. Sensitivity grade consists of Low ➝  
Medium ➝ Very High in the ascending order.  
Alarm-Out  
Selects Alarm-Out scope when Motion occurs.  
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to  
synchronize with the current motion channel. Multi-choice is possible.  
●
Duration  
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.  
Off / 3sec / 5sec / 10sec / 20sec / 30sec  
You may select a time when recording starts automatically.  
Setup by the weekday or time.  
The default is set to “None”.  
Video Loss Detection Setup  
●
●
Pressing “CH > “ copies the value of Channel 1 to all the channels.  
The horizontal axis numbered from 0 to 23 represents the time value.  
The vertical axis numbered from S to H represents the day value.  
(H : Holiday)  
Setup by the weekday or time.  
●
●
Pressing “ALL” converts the overall setting of the selection window into  
Continuous ➝ Event ➝ Both ➝ None.  
Continuous Recording  
Recording starts automatically on the preset time.  
Recording follows the condition established in 5-18.Record Mode of MENU.  
☛ Refer to 7-3 Record Schedule of MENU.  
●
●
Video Loss State  
Off : Image Loss Sensing does not operate.  
On : Image Loss Sensing starts operation.  
●
Event Recording  
Recording starts automatically when Event occurs to Alarm/Motion Detection/Video  
Loss within a designated time.  
Alarm-Out  
Selects Alarm-Out scope when the current Image Loss occurs.  
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to  
synchronize with the current motion channel. Multi-choice is possible.  
Recording follows the condition established in 5-19.Event Record Mode Setup of MENU.  
☛ Refer to 7-4 Event Recording of MENU.  
●
●
Each recording mode has its unique color, Yellow for Sleeping, Blue for  
Event, and Red for Sleeping/Event.  
●
Duration  
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.  
Off / 3sec / 5sec / 10sec / 20sec / 30sec  
Reserved Recording On/Off  
The reserved recording will progress when it’s set to “On,” and the reserved  
recording will not progress when it’s set to “Off.”  
5-23  
5-24  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Backup  
7
●
The detailed items of Backup Menu are as follows.  
●
●
Both(Continuous, Event)  
On occurrence of Event, Continuous Recording is replaced with Event Recording  
Mode.  
HDD Backup Settings  
Holiday  
If you press “Holiday”, a calendar pops up and you are able to designate holidays.  
Move to a date and press “Enter” to complete designation.  
Press “Enter” once more to cancel designation.  
“H” at the bottom of the table means a holiday.  
●
In the presence of the device, the free space and backup device will be  
displayed.  
●
●
Select the backup date and time and the camera number, then press "Start".  
Whenever you change the start date/time, the end date/time, the free space is  
updated and displayed.  
●
●
In case that two devices are connected, select the backup device by  
clicking the USB HDD box at the left bottom.  
In the absence of the backup device, a warning message appears.  
Select and connect the backup device in Menu 5-8, HDD Setup before the backup  
process.  
●
●
Press "Stop" to suspend backup.  
Press "Cancel" during backup to return to the upper menu but the process  
continues nevertheless.  
Caution  
[In the Backup process]  
Press "Cancel" to return to the upper menu but the process continues nevertheless.  
Press "Stop" to suspend backup  
Backup may retard the normal set speed.  
5-25  
5-26  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Network  
8
USB Device Backup Settings  
IP Settings  
●
Connection Mode  
Designates the kind of the network connected to the main body of SHR-4081N/P.  
Static IP : When the main body is connected to the network with Static IP.  
Dynamic IP : When the main body is connected to the network with Dynamic IP  
supplied by DHCP.  
ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE.  
●
Bandwidth  
●
●
●
In the presence of the device, the free space and backup device will be displayed.  
Select the backup date and time and the camera number, then press "Start".  
Whenever you change the start date/time, the end date/time, the free space is updated  
and displayed.  
Designate the speed of the network to which the SHR-4081N/P main body is connected.  
Unlimited/2Mbps/1Mbps/600Kbps/300Kbps  
Caution  
●
●
In case that two devices are connected, select the backup device by  
clicking the USB CD/DVD box at the left bottom.  
If the main frame is connected to a network that uses a high speed LAN, set the  
bandwidth to 1Mbps or 2Mbps. If the main frame is connected to a network that  
supports ADSL or lower bandwidth, set the bandwidth below 600Mbps, and set the  
Record Mode below CIF (STANDARD).  
If you set a higher bandwidth or Record Mode in a network that only supports lower  
bandwidth, the network will be overloaded and the connection to the SmartViewer  
or video monitoring may not operate properly.  
In the absence of the backup device, a warning message appears.  
Select and connect the backup device in Menu 5-8, HDD Setup before the backup process.  
Press "Start" to suspend backup.  
●
●
Press "Cancel" during backup to return to the upper menu but the process  
continues nevertheless.  
Note  
If the Connection Mode is set to ADSL, the bandwidth of IP settings page will be  
locked to 300Kbps, and the protocol type of the transfer protocol settings page will  
be locked to TCP.  
Caution  
[In the Backup process]  
Press "Cancel" to return to the upper menu but the process continues nevertheless.  
Press "Stop" to suspend backup  
●
Admin Password  
The password for the connection between Smart Viewer and the set with the authority  
of Admin. The password can be as long as 8 digits.  
Press "Enter" and the left number keys from 0 to 9 for setup.  
Backup may retard the normal set speed.  
●
●
User Password  
The password for Smart Viewer’s access to the set with the authority of general user.  
IP  
Set up the IP address to connect the SHR-4081N/P main body to the network.  
In case of a fixed IP, you must input IP yourself.  
In case of a flexible IP or ADSL(PPPoE), the IP allocated from the DHCP server or  
ADSL company. If you fail to connect DHCP or ADSL, 000.000.000.000 is displayed.  
Then, press "OK" to receive IP. If you repeatedly fail to connect DHCP or ADSL, turn the  
SHR-4081N/P main body power off and turn it on again before you retry connecting.  
5-27  
5-28  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
●
●
Gateway  
Transfer Protocol Settings  
Determines Gateway Address in the SHR-4081N/P main body.  
Subnet Mask  
Determines Subnet Mask Address in the SHR-4081N/P main body.  
DNS  
Sets up DNS Address in the main body of SHR-4081N/P. The default of DNS is  
168.126.63.1. Generally, you don’t have to alter the DNS default but you may be hard to  
connect to the network sometimes if you use DHCP or ADSL. In this case, call the  
network manager or ADSL company to set up a new DNS address.  
●
●
●
You may choose the protocol type, either TCP or UDP.  
ADSL setup in the IP setup page can be made only to TCP.  
Port(TCP) can be selected from 554 to 998, increasing by 4.  
Once the first digit is chosen, the rest 3 digits will follow the first digit.  
Port(UDP) can be selected from 8000 to 9760, increasing by 160.  
Once the front port is chosen, the rest ports will change accordingly.  
●
ADSL User ID  
If the main body of SHR-4081N/P is connected with the ADSL(PPPoE) network, input  
User ID subscribed to the ADSL company. You may input User ID with a Virtual  
key-board as long as 40 digits irrespective of alphabets, numbers, or symbols.  
●
●
Unicast/Multicast has the default of Unicast and you may choose Multicast.  
Multicast IP shall be set to Multicast from Multicast/Unicast to be activated and for IP  
setup.  
Sets up the D-Class IP address from 224.0.0.0 to 239.255.255.255.  
TTl shall be also set to Multicast from Multicast/Unicast to be activated and to  
choose a value from 1-255. The default is 5.  
●
Password  
If the main body of SHR-4081N/P is connected to the ADSL(PPPoE) network, input the  
user password subscribed to the ADSL company. You may input the password with a  
Virtual keyboard as long as 40 digits irrespective of alphabets, numbers, or symbols.  
●
●
DDNS Site  
- You may select the DDNS Site as Off, Samsung DDNS, dyndns.com, no-ip.com, or  
changeip.com.  
- If you select Off, the IP will not be registered in DDNS.  
- If you select Samsung DDNS, the IP will be registered in the DDNS operated by  
Samsung.  
Select MAC Address as the Address Type in the Setup ➝ Site Setup ➝ DVR regis  
tration window of the SmartViewer, and enter the MAC Address of DVR  
(SHR-4081N/P), then you can connect remotely using the Samsung DDNS.  
- dyndns.com, no-ip.com, and changeip.com are free Public DDNS websites that a URL  
can be allocated by registering a Dynamic IP.  
Become a member of the desired website, register the URL, and then set up your  
Host Name, User Name, and User Password.  
Select URL as the Address Type in the Setup ➝ Site Setup ➝ DVR registration  
window of SmartViewer, and enter the Host Name (URL) that is allocated by the  
Public DDNS website, then you can connect remotely using the URL.  
Caution  
Be sure to set up IP/SubnetMask/Gateway/DNS to let Smart Viewer connect with the  
main body of SHR-4081N/P.  
Wrong IP/Gateway/SubnetMask/DNS may prevent Smart Viewer from being  
connected to the main body of SHR-4081N/P.  
Please call the network manager or ADSL company to get each setting value.  
Caution  
IIn the ADSL connection mode, SmartViewer does not support Audio replay.  
Note  
If you set up the Public DDNS (dyndns.com, no-ip.com, or changeip.com), it will take  
approximately 30-60 seconds for the IP address of the Host Name (URL) to be updated  
in the DNS.  
5-29  
5-30  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Network Setup  
9
Port setup for SmartViewer connection.  
Note  
●
The port value shall be the same as the Port(TCP/IP) value of the set to  
If you want to connect IP Router with the main body of SHR-4081N/P, you shall  
designate a port for SHR-4081N/P in the IP Router setup menu.  
register DVR(Setup ➝ Site Setup) with SmartViewer.  
The SHR-4081N/P main body uses 4 ports for TCP communication and further 160  
UDP ports when the procotol type is set to UDP. In addition, if you want to use the  
DHCP function backed by IP Router to allocate Dynamic IP to the main body of  
SHR-4081N/P, you shall designate a port for the IP which SHR-4081N/P has been allo-  
cated by the IP Router setup menu.  
If you use IP Router, you are recommended to rather determine IP and Port numbers to  
be allocated to the main body of SHR-4081N/P from the IP Router setup menu, set the  
connection mode to Static IP for the main body of SHR-4081N/P, and input the  
determined IP and Port number in IP Router than use the DHCP function.  
Please refer to the IP Router User’s Manual or call the manufacturer to set up IP Router.  
●
When you use an IP router, you shall forward the activated port by the current  
setting value.  
- In case of TCP/IP, set 4 ports(TCP/IP) in the IP router.  
- In case of UDP, set 4 ports(TCP/IP) and 160ports(UDP) in the IP router.  
When you set to TCP/IP from the Transfer Protocol Setttings page  
●
The ports set in Port(TCP/IP) shall be used to control SmartViewer connection  
and transmit Stream.  
Callback Settings  
●
Callback delivers a callback message to the IP where SmartViewer is already running when  
an event corresponding to Alarm, Motion Detection, or Video Loss occurs from the set.  
When you set to UDP from the Transfer Protocol Setttings page  
●
The ports set in Port(TCP/IP) shall be used to control SmartViewer connection  
and those set in Port(UDP) shall be used to transmit Stream.  
●
In case of Multicast  
- The MultiCast IP and TTL Setup menu will be activated.  
-
MultiCast IP indicates the group address for Multicast transmission(D-Class IP Address :  
224.0.0.0 ~239.255.255.255).  
- TTL(Time To Live) indicates how many routers Multicast shall get through.  
- If you are unable to Multicast due to the network(LAN or ADSL) characteristics as both  
the set and SmartViewer are installed, SmartViewer displays "Not Connected" in the  
screen. In this case, reset to TCP/IP or UDP(Unicast).  
●
●
On/Off : Off is the default and On is optional.  
IP Address : IP setup is available only when On/Off is set to On. Sets up the IP  
address of a PC where SmartViewer is already running.  
●
In case of abnormal screen replay from SmartViewer  
●
●
Port(UDP) : You may choose a value from 7900 to 7999, increasing by 1. Sets  
up the port value of Callback Connection set by SmartViewer.  
- This may happen when the network bandwidth of the set is smaller than the packet  
quantity of Transmission Stream. Then, reduce the IP setup bandwidth(to 300Kbps or  
600Kbps when installed to the ADSL network).  
Retry : You may choose a value from 1 to 20, increasing by 1.  
- If this does not work, reset the protocol type to TCP/IP.  
Caution  
- Though Callback is set to ON, there will be no Callback message unless Alarm,  
Motion Detection, or Video Loss is set by Event Record.  
- Unless you click the Callback button of SmartViewer, SmartViewer does not receive  
any Callback message.  
5-31  
5-32  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6  
PTZ device Control  
6
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
PTZ device Control Mode  
1
●
Select a proper PTZ Device Configuration value in MENU to enter PTZ Control  
Mode.  
●
Other PTZ device Control Modes perform its control in a single screen. Press the  
channel selection button in the left front to select the channel whose Menu  
selected PTZ and then press the PTZ button. If you succeed in entering Single  
Screen PTZ device Control Mode, the PTZ symbol on the screen will turn yellow  
from white while the PTZ button will turn blue. Single Screen PTZ device Control  
Mode supports Pan, Tilt, and Zoom operation basically and Preset, Camera Menu,  
and other functions additionally.  
●
●
Selected in MENU, the symbol( PTZ ) of PTZ is displayed on the channel in the  
screen.  
If you press the Enter(  
) button among direction keys in front of Split Screen,  
¦
a blue bar will appear in the monitor screen. Use direction keys to move this bar  
until you reach the channel with the PTZ symbol and press the PTZ button in front  
of SHR-4081N/P to enter PTZ device Control Mode.  
If you succeed in entering PTZ device Control Mode, the PTZ symbol on the  
monitor screen will turn yellow from white while the PTZ button in front of  
SHR-4081N/P will turn blue. PTZ device Control Mode supports Pan, Tilt, and  
Zoom operation.  
●
Press the PTZ button in Live Mode to cancel PTZ device Control Mode. After  
cancellation, the PTZ symbol on the screen will turn white from yellow while the  
PTZ button will lose its blue light.  
Note  
If you select Remote Control Device, you may not control PTZ device with SHR-  
4081N/P. It’s because the PTZ button in front of SHR-4081N/P remains inactivated.  
Press the PTZ button and the PTZ ban icon(  
) will appear. It’s because the  
RS-485 port setup was done for Romote Control Device.  
Some functions of PTZ camera may not be used for SHR-4081N/P.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
●
When using a remote control device (SCC2000), you may perform camera control  
from the remote control device (limited to Samsung Protocol). (Refer to SCC2000  
User’s Manual.)  
The PTZ Mode will be automatically when there is no PTZ control in the DVR for  
up to 5 minutes. This is to enable the PTZ control from the remote Viewer when  
there is no PTZ control.  
6-1  
6-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
PRESET Setup  
Basic Operation of PAN, TILT, & ZOOM  
3
2
●
Records a certain position of PTZ device.  
●
PAN  
Press the LEFT or RIGHT button in front SHR-4081N/P in PTZ device Control  
Mode to control PTZ device horizontally.  
●
Memorizes up to 20 PTZ device positions at the moment.  
Note  
PTZ  
TELE  
WIDE  
For AD Protocol PTZ device , this memorizes only 7 positions.  
VIEW  
PRESET  
●
Press the SET button in front of SHR-4081N/P in Single Screen PTZ device  
Control Mode to set up Preset.  
●
TILT  
Press the UP or DOWN button in front SHR-4081N/P in PTZ device Control Mode  
to control PTZ device vertically.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
●
ZOOM  
Press the TELE/WIDE button in front SHR-4081N/P in PTZ device Control Mode  
to zoom in or out PTZ device.  
●
After PRESET setup, press ENTER.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
6-3  
6-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Camera Menu Setup  
4
●
●
Move the cursor right and press ENTER in PTZ Control Mode first. Then, press  
Enter to run P/T/Z/ Motion Mode in the PIP screen and press Enter again to cancel  
P/T/Z/ Motion Mode.  
●
Camera Menu is a menu supplied by PTZ device itself. This Menu sets up several  
conditions of PTZ device.  
Press Enter at the Position Name position to see Virtual Keyboard. Type Position  
Name and press OK to save Position and Position Name.  
Note  
Either Pan. or Samsung Protocol Camera only is authorized for Camera Menu setup.  
●
Press the SET button in front of SHR-4081N/P in Single Screen PTZ device  
Control Mode to select Camera Menu.  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
●
●
Press Del to delete both Position and Position Name with the number.  
Press Del ✓ on the top to delete all Positions and Position Names in memory.  
●
Press the SET button in front of SHR-4081N/P to return to the upper menu from  
SET button Camera Menu.  
6-5  
6-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Other View  
Preset View  
6
5
●
Preset setup allows your movement to a certain saved position of PTZ device.  
●
Press the VIEW button in front of SHR-4081N/P in Single Screen PTZ device  
Control Mode to supply PTZ device. This is a very special function.  
●
Press the VIEW button in front of SHR-4081N/P in Single Screen PTZ device  
Control Mode to select Preset.  
Note  
Samsung, Pan., Pel.-P, or Pel.-D Protocol PTZ device supplies this function.  
Samsung : Auto Pan / Scan / Pattern  
Pan. : Auto Pan / Sequence / Sort  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
Pel.(P,D) : Auto Scan / Frame Scan / Pattern  
PTZ  
TELE  
WIDE  
VIEW  
PRESET  
(For example, Samsung Protocol)  
Preset  
Auto Pan  
Scan  
Pattern  
EXIT  
Preset Auto Pan  
Sequence  
Sort  
EXIT  
Preset Auto Scan  
Frame Scan  
Pattern  
EXIT  
●
Control the cursor until it reaches a Preset position number that you want to move  
to and you can check the right movement through in PIP Screen on your right.  
Samsung  
Pan.  
Pel.  
●
●
After you select a function, press Enter. Then the function will be checked and  
start running.  
If you select other function while this function is in action, the previous function will  
be unchecked and the current function will be checked.  
(For example, Samsung Protocol)  
●
●
If you put P/T/Z/ in operation or enter Preset Setup or Camera Menu Setup Menu  
while this function is in action, the function in action will be suspended and  
unchecked.  
Restart of SHR-4081N/P System in action has no effect. The function continues its  
duty and remains checked.  
6-7  
6-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7  
Recording  
7
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N USER’S MANUAL  
PANIC (Emergency Recording)  
REC (Normal Recording)  
1 2  
●
Pressing the button records all the images input so far.  
●
Pressing REC the button starts recording as set in Record Mode of MENU.  
Then, REC LED lights on and a recording icon appears on the screen. During  
recording in HDD, HDD LED in front blinks.  
Emergency Record has the characteristics of CIF size, Very High resolution, and  
15ips(NTSC)/12.5ips(PAL). During PANIC Recording, LED lights on and a recording  
icon appears on the screen. During recording in HDD, HDD LED in front blinks.  
●
●
During REC Recording, you may stop REC Recoding by pressing the REC button  
then REC LED lights out.  
●
During PANIC Recording, you may stop PANIC Recoding by pressing the button  
then LED lights out.  
If you press the REC LOCK button during REC Recording, REC LOCK LED will  
light on and the REC button will be locked. Cancel REC LOCK first and press the  
REC button to cancel REC.  
Warning  
If you carry out the functions necessary to stop recording(Time Change, File Delete,  
HDD Connect/Disconnect, etc.), recording will be paused.  
Warning  
If you carry out the functions necessary to stop recording(Time Change, File Delete,  
HDD Connect/Disconnect, etc.), recording will be paused.  
7-1  
7-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N USER’S MANUAL  
Event Recording  
Record Schedule  
4
3
●
While “Continuous Recording” or “Both” is selected for Record Schedule in MENU,  
Timer Recording automatically starts. Otherwise, Timer Recording remains  
inactivated. During Timer Recording, Recording Icon appear on the screen. During  
recording in HDD, HDD LED in front blinks.  
●
Alarm Detection Setup  
Sensor State in Event Record Alarm of MENU shall be set to N.O (Normal Open)  
or N.C (Normal Close)  
●
●
●
Motion Detection Setup  
M.D State in Event Record Motion Detection of MENU shall be set to On.  
Video Loss Detection  
Image Loss State in Event Record Image Loss of MENU shall be set to On.  
Event Record Mode Setup  
When Event occurs, it designates recording type. In particular, depending on  
Pre-Event Off or Post-Event Off, Pre-Event or Post-Event Recording is  
disabled respectively.  
Warning  
●
During the event recording, the auto recording is operated when the event occurs.  
In this case, the event recording is saved according to the related channel setup  
within the event recording items(Resolution, Frame, Pre-alarm, Post-alarm) of  
recording menu.  
If you carry out the functions necessary to stop recording(Time Change, File Delete,  
HDD Connect/Disconnect, etc.), recording will be paused.  
Note  
Even in case of an event, Event Recording will not start unless Event Recording or  
Both is selected in Record Schedule.  
Warning  
If you carry out the functions necessary to stop recording(Time Change, File Delete,  
HDD Connect/Disconnect, etc.), recording will be paused.  
7-3  
7-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8  
Search Play  
&
8
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N USER’S MANUAL  
Before Use  
Calendar Search  
1
●
●
●
●
●
●
●
Pressing the SEARCH button shows Search Menu on the screen as seen above.  
CALENDAR uses a calendar to search video files at the preset time.  
Event Search searches video files recorded by Event.  
●
●
●
●
●
●
Be sure to designate both the channel and the date first. Then press [OK] button  
to initiate search.  
Uses a calendar to search video files at the preset time. Four channels as a  
maximum are in the range of search.  
Date/Time inputs a day and time on which the system searches video files.  
Go To First searches video files from the oldest one.  
Press [Enter] ¦,and ‹¤to choose 4 channels as a maximum and the date column  
with recorded video image will turn blue.  
Go To Last searches video files from the latest one.  
Use ƒ¤to move to the row where you are able to choose a year/month and press  
[Enter] ¦, and ‹ to select a year/month as you wish.  
Backup Search searches backed-up video files.  
- If you select the external HDD, you are able to search IEEE1394 HDD and USB  
HDD.  
- If you select the external USB device, you are able to search Memory Device  
and USD CD/DVD.  
Press [Enter] to select a date with a recorded image and the box on the right of  
the number indicating the date will appear after checked.  
Press ƒ¤to move to Time Bar and press ¦, and ‹ to move to the time that you  
want and press [Enter] to select the time.  
●
●
Press [OK] to start search and press [Cancel] to move to the previous menu.  
The Time bar appears every 30 minutes.  
Note  
During Backup Pressing the Search button will have no effect to let you enter the  
Search mode. (  
)
8-1  
8-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Date/Time Search  
Event Search  
3
2
●
Searches Normal Recording, Panic Recording, Sched.(Schedule) Recording,  
Alarm Recording, Motion Recording, and Image Loss Recording by the time.  
●
●
●
Use the Date/Time information to search video files at the time as you desire.  
Up to 4 channels can be searched at once.  
●
●
You shall select a channel to search to see the Event information of the channel.  
Press œ, ƒ, and [Enter] to select a channel and the box on the right of the  
channel will be checked.  
On the basis of the Event information for each channel, the system searches the  
video file for the event. Only one channel is allowed for video search.  
After channel selection, press ƒto move to the row where you can choose the  
search time. To change the search time, press [Enter]. The search time can be  
controlled by years/months/days/hours/minutes/seconds and each value can be  
changed by pressing œ, ƒ¤For your convenience, keep pressing the button to  
change the value continuously.  
●
●
●
Press [Enter] ¦, and ‹¤to select a channel and the event list for the selected  
channel only will be displayed.  
After channel selection, press œ, ƒ, and [Enter] to select a channel from the  
event list. The box on the left of the selected event number will be checked.  
●
●
Press ƒ¤to move to [Start] and enter [Enter] to initiate search and move to  
[Cancel] and press [Enter] to cancel search.  
Press ƒ¤to move to [Start] and press [Enter] to start search and move to [Cancel]  
and press [Enter] to cancel search. Press [Next] followed by [Enter] to see the  
event list in the next screen and press [Prev] followed by [Enter] to see the event  
list in the previous screen.  
The time information in the bottom left corner, 2004-03-10 08:38:58 indicates the  
time when play starts.  
8-3  
8-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Go to Last Search  
Go to First Search  
5
4
●
●
●
Searches the oldest one among recorded video files. Up to 4 channels can be  
searched at once.  
●
●
Searches the latest one among recorded video files. Up to 4 channels can be  
searched at once.  
œ, ƒ, Press [Enter] to select a channel and the box on the right of the channel  
will be checked.  
œ, ƒ, Press [Enter] to select a channel and the box on the right of the channel  
will be checked.  
Press [Start] to start searching and press [Cancel] to return to the previous menu.  
●
●
Press [Start] to start searching and press [Cancel] to return to the previous menu.  
Recent Search is used to search the image at the moment that you start searching.  
8-5  
8-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Play  
6
‹ ꢀ¤  
●
Press the PLAY/PAUSE button(  
) to play the data recorded in HDD.  
●
Play Screen Mode Definition  
II  
●
This chooses out a channel with the oldest data among recorded channels and  
plays the data from the first part of the channel. If you used the SEARCH button  
for play just before, the system would remember the information of the played  
channel until you click the PLAY/PAUSE button( ‹ ꢀ¤ ) again, then the system  
II  
plays the previous channel.  
PIP Screen  
Single Screen  
9 Split Screen  
4 Split Screen  
‹ ꢀ¤  
If you press the PLAY/PAUSE button(  
as you never tried Play.  
), the Search Menu will appear as far  
II  
PIP Screen Single Screen 4 Split Screen 9 Split Screen Whenever  
you press [Mode], the Play screen becomes 4Split, Single, PIP, 9Split in turn.  
If you select only one channel from Searh, the 4 Split screen will not appear.  
Note  
- Pressing the PLAY button( ‹ ꢀ¤ ) does not affect play as far as the user stays in  
II  
MENU. Be sure to escape from MENU to start play.  
① 4 Split Screen : If you select more than one channel from Search, the 4 Split screen will appear.  
➁ Single Screen : This screen appears when you choose only one channel from Search.  
If you press [Enter] in the 4 Split screen, a blue bar will appear.  
Place the bar in the position that you wish to and press [Mode],  
the selected channel will become the Single screen. Press the  
[ZOOM] button to enlarge the selected area twice.(Refer to 4-6,  
Zoom Function.)  
■
●
Press the STOP button(  
) to stop play. If you press the Playback/PAUSE  
‹ ꢀ¤  
button(  
), recording will resume from the point where the previous recording  
stops. When the data position reaches the end of HDD during play, play will be  
paused.  
II  
➂ PIP Screen : Press [Mode] during Single screen play and it will be displayed in  
the PIP screen.(The larger screen displays the channel in play and  
the smaller screen in the bottom right corner displays Live CH in  
the form of PIP.) Use œ, ƒ to move the smaller PIP screen(Live  
CH) vertically. Press [Enter] and a blue bar will appear in Live CH.  
Press the CH button and the Live screen will become the selected  
channel.  
➃ 9 Split Screen : Press [Mode] in the PIP screen and the 9 Split screen(Live 8CH  
+ Play 1CH) will appear. You may set the Play screen position to  
"Center" or "Bottom Right" by pressing Menu ➝ Monitoring  
Menu ➝ PB CH Position.(9 Split only)  
Press the [Enter] button and a blue bar will appear in Live CH.  
Press the CH button that you wish and the Live screen will be  
converted into the selected channel.  
Press [Mode] button to move to the 16 split screen again.  
8-7  
8-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
●
Play at Faster Speed  
‹‹  
¦¦  
If you press the LEFT or RIGHT button(  
/
) or use the Shuttle during  
play, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed  
either forwardly or reversely.  
Viewing Still Screen  
If you press the LEFT or RIGHT button(  
¦¦  
/
) or use the Jog shuttle with  
‹‹  
the system paused, you will be able to see still screens forwardly or reversely.  
During reverse search, the interval between cuts varies depending on the record-  
ing specification.  
●
Audio On/Off  
If you press the “16” button in other screen than 4 Split Screen(i.e. Single Screen,  
PIP Screen, and 9 Split Screen), you will be able to turn Audio of the channel in  
play on or off. In 4 Split Screen, Audio is not activated.  
Chapter 9  
Backup and  
Backup Search  
8-9  
9
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Backup  
1
1. IEEE1394 HDD and USB HDD  
2. CD/DVD and USB Memory  
1.1 Backup Start  
1.1 Backup Start  
Before backup, HDD(IEEE1394, USB) shall be connected for such purposes.  
① Choose USB Memory or USB CD/DVD as a backup device.  
➁ Select a backup channel and change the tiem when back starts and ends.  
➂ The backup video file size shall be maintained below the free space of USB  
Memory and USB CD/DVD.  
➃ Press "OK" to back up the video data of the selected channel at the designated  
time in USB Memory and USB CD/DVD.  
① Choose either IEEE1394 HDD and USB HDD as a backup device.  
➁ Select a backup channel and change the tiem when back starts and ends.  
➂ The backup video file size shall be maintained below the free space of the  
external HDD.  
➃ Press “OK” button to back up the video data of the selected channel at the  
designated time in the external HDD.  
Note  
1. Pressing "Cancel" Button does not cancel nor stop backup but move to the upper  
menu while backup contines.  
Note  
Pressing "Cancel" does not cancel nor stop backup but move to the upper menu  
while back continues.  
Pressing "Stop" stops backup.  
2. Pressing "Stop" stops backup.  
3. Both USB CD/DVDs are not allowed in the USB connection port in front of and  
behind SHR-4081N/P.  
4. Both Memory Devices are not allowed in the USB connection port in front of and  
behind SHR-4081N/P.  
1.2 Backup Stop  
① Select Stop in the backup process to stop backup.  
➁ Then, the Backup menu will be displayed in the screen.  
➂ If you change the system time or terminate the system, the current backup  
process will be paused.  
1.2 Backup Stop  
① Select Stop in the backup process to stop backup.  
➁ Then, the Backup menu will be displayed in the screen.  
➂ If you change the system time or terminate the system, the current backup  
process will be paused.  
1.3 Backup Play  
1.3 Backup Play  
① Press the SEARCH button in front of SHR-4081N/P and press the Backup  
① Press the SEARCH button in front of SHR-4081N/P and press the Backup  
Search menu to play backup.  
➁ To search backup, select the device.  
Search menu to play backup.  
➁ To search backup, select the device.  
➂
Select a channel and time in the Backup Search menu and press the time for play.  
➂
Select a channel and time in the Backup Search menu and press the time for play.  
Note  
Note  
Backup can not be played during backup.  
Refer to the User’s Manual 8-7, Backup Search.  
Backup can not be played during backup.  
Refer to the User’s Manual 8-7, Backup Search.  
9-1  
9-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Backup Search  
2
1. Backup search menu  
Caution  
1. During backup, you shall not separate the backup device from SHR-4081N/P.  
2. During backup search, you shall not separate the backup device from  
SHR-4081N/P.  
3. Be sure to detach the device before you separate the backup device from  
SHR-4081N/P(refer to User’s Manual 5-8, HDD and External Device Setup.).  
4. In case of backup by using a USB memory, be sure to format with FAT32 and use  
a USB memory device with one partition. In addition delete the USB memory at  
SHR-4081N/P for safe backup(refer to 5-7, System Information and Setup.).  
5. When you connect the backup device to SHR-4081N/P, it takes some time for  
SHR-4081N/P to recognize the backup device. Consequently, connecting the  
backup device to SHR-4081N/P and executing backup may not result in the  
connection of the device. In such a case, please retry shortly later.  
1-1. External HDD Search  
● If you select an external HDD, you may search the data by using Date, Event,  
Origin, or Late.  
Refer to p8.2~p8.5 for this purpose.  
9-3  
9-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
1-2. USB Device Search  
● Select an external USB device to search a date.  
● Use the weekday/time information in the backup image to search images  
contained in as many as 4 channels.  
● Click œ, ƒ, [Enter] to select a channel and the box on the right of CH No.  
shall be checked.  
● After channel selection, click the ƒ¤button to move to the time search line.  
Click [Enter] to change the search time. The search time may be changed by  
Year/Month/Day/Hour/Minute/Second by clicking œ or ƒ. For your convenience,  
just keep pressing a button and the value will continue to change.  
● Click [Start] to start searching and [Cancel] to return to the previous menu.  
● The time information in the bottom left corner, 2004-03-06 17:47:27 indicates  
when to start replay.  
9-5  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10  
Smart Viewer  
10  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Introduction  
Feature  
1 2  
Smart Viewer is a program that a general PC user is able to install SHR-4081N/P to  
his PC to monitor the search video and audio data through Network without going to  
the site where SHR-4081N/P is installed by himself.  
●
●
●
Thanks to the transmission of video data compressed by the MPEG-4 Video  
Compression method, this plays video images of good quality.  
Thanks to the G.726 Voice Compression method, this supplies voice data of good  
quality. Use of armored MIC improves the quality of remote voice.  
Thanks to the transmission of video/audio stream through RTP(Real-Time  
Transport Protocol), real-time video play capacity is excellent and multi-users’  
simultaneous connection does not affect the transmission speed in whole abruptly.  
●
Command & Control by RTSP(Real-Time Streaming Protocol) enables safety  
control through Network.  
●
●
Supports various transmission protocols (TCP/IP, UDP(Unicast, Multicast)).  
Connection is open to you at any time to monitor video and audio data by inputting  
IP Address only.  
●
You can not only perform real-time recording ( .dvr format) whereas necessary  
*
during monitoring but also convert recorded video files ( .dvr format) into frame  
*
unit images((JPEG format).  
●
●
One DVR set allows 3 Smart Viewer users(or 6 with Multicast) at the same time.  
With a Smart Viewer, you are allowed to connect to as many as 9 SHR-4081N/P  
to monitor them simultaneously.  
●
Smart Viewer is optimized in the resolution of 1024X768  
10-1  
10-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Smart Viewer Installation  
PC Specification(Recommendation)  
4
3
●
OS : Win98SE, WinMe, Win2000, WinXP  
Smart Viewer Installation  
●
Put a Smart Viewer Program CD in and open the “Smart Viewer” folder in CD.  
●
Recommendation :  
CPU Pentium3 1GHz or higher  
RAM 256 Mb or higher  
VGA RAM 32Mb or higher  
DirectX 8.1 or higher  
Note  
Depending on Recording Rate, Video Size, and user’s PC specification set to  
SHR-4081N/P, the number of Smart Viewer play frame varies.  
For the detailed specification, refer to Appendix 5.  
●
Run the “Setup.exe” file.  
10-3  
10-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Click the “Next” button.  
●
The system proceeds with setup file installation and system setup.  
●
If you agree with Smart Viewer License, click “Yes”.  
●
Installation is complete. Press “Finish” to terminate installation.  
●
Designate a folder to install Smart Viewer in it and click “Next”.  
10-5  
10-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Smart Viewer Initial Screen  
Smart Viewer Program Execution  
6
5
●
Double-click the Smart Viewer icon in the background screen to run the program.  
●
Screen Description  
2
1
3
4
6
5
7
8
11  
10  
9
12 13 14  
!
Pressing this button enters Search Mode in which you can search and play the  
video data recorded both in Monitoring Mode for real-time video data monitoring  
and in SHR-4081N/P.  
@
#
$
%
^
This button terminates or minimizes the program.  
It displays the current date, day, and time.  
This button is used for the connection with the preset DVR(SHR-4081N/P) or site.  
This screen shows the monitoring video image.  
These buttons are used to select the window to display event messages and came  
connection condition.  
&
*
(
This window displays the event message from SHR-4081N/P real-time.  
These buttons display the status of channel being played in the present .  
This button adjusts Audio Volume and Video Brightness/Contrast or records video  
data.  
)
1
2
3
4
This button is used for PTZ related functions.  
This button is used for screen split and Sequence Mode.  
This button is used for Callback connection.  
This button is used for the Favorite function to contact a site.  
This button puts up the Setup Mode window to change Smart Viewer or  
SHR-4081N/P setup. (Refer to 10-30. Setup Mode.)  
10-7  
10-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Monitoring Mode  
7
●
DVR(SHR-4081N/P)/SITE Connection  
- Select the name of DVR(SHR-4081N/P) or site for connection and click the  
connection button.  
Note  
No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to  
access SHR-4081N/P simultaneously. One SHR-4081N/P allows as many as 3 users, 1 Admin  
and 2 Users for simultaneous connection(or as many as 6 users including 5 Users for  
Multicast).  
Caution  
Only 3 users can be connected to the SHR-4081N/P( 6 Users in Multicast).  
Note  
●
Monitoring Mode Connection Screen  
You can determine the name, IP, and password of DVR(SHR-4081N/P) for  
connection in Setup Mode. Also, setup of a site which permits simultaneous  
connection to multi-DVRs(SHR-4081N/P) is available in Setup Mode.  
When you connect to the SITE, you may connect to a maximum number of 16 DVRs  
(SHR-4081N/P) simultaneously.  
ꢀ Connection Failure Cases  
1. Password Certification Failure  
- In case of discord between the Network password set to SHR-4081N/P and the  
connection password set to Smart Viewer, a window pops up to induce retry of  
password input.  
2. Admin User Connection Failure  
Caution  
If you alter “Resolution” or “Color Quality” from the setup tab of [Display  
Registration Information] while Smart Viewer is running, Smart Viewer will fall into  
an unexpected condition.  
You shall terminate Smart Viewer first to recover the condition.  
●
Mode Conversion Button  
- Where SHR-4081N/P that you wish to connect to has been already occupied by  
other user in an Admin. Capacity, you are authorized with access to  
SHR-4081N/P concerned in a User capacity.  
- This button changes Monitoring Mode or Search Mode.  
10-9  
10-10  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Time Information  
Note  
# Clicking the speaker icon turns Audio of a channel on or off.  
: Audio OFF  
: Audio ON  
If you turn Audio of a SHR-4081N/P channel off, Disable will be displayed.  
: Audio Disabled  
- As soon as you are Connected to SHR-4081N/P, the date, weekday, and time of the  
set to which the selected channel is connected.  
- If SHR-4081N/P is not connected, the present date, weekday, and time of the user's  
PC are displayed.  
✴ For the channel with Audio turned on now, use the following Audio relate button  
to control Audio volume and set up MUTE.  
✴ Once TCP/IP is selected, Audio will be turned off.  
●
Connection Information  
Note  
- As soon as you are connected to SHR-4081N/P, the connection button will  
display connection status.  
% Where Alarm or Motion Detection occurs at a channel of SHR-4081N/P with  
Alarm or Motion Detection established, an icon pops up on the screen real-time.  
: Motion Detection  
: Alarm Event  
- If you click the connection button here, connection will be cancelled.  
Note  
●
Play Screen OSD Information  
^ If you connect and set up PTZ device in SHR-4081N/P, PTZ controllability of the  
2
3
1
channel will be displayed.  
✴ Select a channel capable of PTZ and use the PTZ related buttons at the bottom to  
control PTZ. (Refer to the description of PTZ Related Button.)  
4
6
5
!
@
Channel no., camera name, and video size will be displayed.  
Video Size (C) CIF / (N) Normal / (L) Large  
The Video data of the current channel are recorded in your PC with REC mark  
displayed.  
#
$
%
^
Audio ON/OFF Button is marked.  
Displays the name, IP address, and play time of the current SHR-4081N/P.  
The current channel alarm status is displayed.  
Possibility of the current channel PTZ controllability is displayed.  
10-11  
10-12  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Event Log Display Window  
Caution  
When Time Change, Load Factory Default, Network Change, System Shutdown,  
or Hdd Format event occurs, Smart Viewer terminates automatically.  
●
Camera Connecting Indication Window  
- Click the Log button to activate the Log Display window.  
- Displays the event(alarm, user connection, and setup change) occurring at  
SHR-4081N/P real time.  
Note  
[Event Message]  
‹ Connecting.. : Trying to connect to SHR-4081N/P.  
‹ Connected.. : Succeeded connecting to SHR-4081N/P.  
‹ Connection Failed : Failed in connecting to SHR-4081N/P.  
‹ Disconnected.. : Finished connecting to SHR-4081N/P.  
‹ Setup(Remote) : SHR-4081N/P at DVR Setup of Viewer changed.  
‹ Setup Start / End (Local) : Start/Finish the Menu screen at SHR-4081N/P.  
‹ Video Loss CH[N] : Video Loss at the N channel of SHR-4081N/P encountered.  
‹ Time Change : Date/Time of SHR-4081N/P changed.  
‹ Load Factory Default : SHR-4081N/P System initialized.  
‹ Network Change : SHR-4081N/P Network setup changed.  
‹ System Shutdown : SHR-4081N/P System terminated.  
‹ Hdd Format : SHR-4081N/P HDD initialized.  
- List displays the connection condition of DVR and CAMERA.  
Note  
[DVR Icon Mark]  
‹ If you succeed in SHR-4081N/P connection, the icon will be turned yellow,  
otherwise black.  
[DVR Icon Mark]  
‹ During monitoring by connecting with CAMERA, it will turn yellow.  
‹ Depending on the availability of connection, it turns blue(Able) or black(Disable).  
‹ Disk Full : No more space in SHR-4081N/P HDD.  
‹ Power Failure Recovery : SHR-4081N/P resumed after power failure.  
‹ Backup Start/End/Fail/Stop : Backup at SHR-4081N/P  
started/finished/failed/stopped.  
‹ Network Traffic Busy : When the data is not transferred smoothly  
‹ Access Denied(Limit Over) : When user can be connected are exceeded  
10-13  
10-14  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Screen Split Selection Button  
- Full Screen / Single / Quad / Nine-Split Mode  
- You may change the Split Mode of the screen under monitoring.  
●
Sequence Mode Button  
: During monitoring in Quad Mode  
- Changes the channel to be played at the preset interval.  
- The sequence time interval setup follows the procedure of Setup Mode ➝  
Viewer Setup.  
- In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 5 ➝ 6 ➝ 7 ➝ 8 ➝ 1 (CH)  
- In Quad Mode : 1,2,3,4 ➝ 5,6,7,8 ➝ 1,2,3,4 (CH)  
- In Nine-Split Mode : 1,2,3,4,5,6,7,8 ➝ 1,2,3,4,5,6,7,8,9 (CH)  
: During monitoring in Single Mode  
Note  
If you connected with multi-DVRs(SHR-4081N/P) through a site, Sequence will operate as  
follows.  
- In Single Mode : DVR1:1CH ➝...➝ DVR1:8CH ➝ DVR2:1CH ➝...➝ DVR1:1CH  
- In Quad Mode : DVR1:1,2,3,4CH ➝...➝ DVR1:1,2,3,4CH ➝ ...  
- In Nine-Split Mode : DVR1:1,2,3,4,5,6,7,8CH ➝DVR2:1,2,3,4,5,6,7,8CH ➝...  
: Camera Off  
●
Monitoring Screen Condition Information / Selection Button  
- Displays the Split or Monitoring condition of the screen in play.  
Note  
The figure in a screen icon indicates the screen position in SmartViewer.  
: The orange icon indicates the current channel is connected to a camera.  
: The gray icon indicates the channel is connected to a camera but not displayed  
on the screen.  
: The black icon with a diagonal line indicates no camera is connected.  
: During monitoring in Nine-split Mode  
10-15  
10-16  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
NEXT Button  
●
FAVORITE Button  
-
Click NEXT(Mouse Left Button) to see the channel next to the current monitoring channel.  
- In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 5 ➝ 6 ➝ 7 ➝ 8 ➝ 9 ➝ 10 ➝ 11 ➝ 12 ➝ 13  
➝ 14 ➝ 15 ➝ 16 ➝ 1 (CH)  
- Click the FAVORITE button to activate the FAVORITE window.  
- In Quad Mode : 1,2,3,4 ➝ 5,6,7,8 ➝ 9,10,11,12 ➝ 13,14,15,16 ➝ 1,2,3,4 (CH)  
-
In Nine-Split Mode : 1,2,3,4,5,6,7,8,9 ➝ 10,11,12,13,14,15,16 ➝ 1,2,3,4,5,6,7,8,9 (CH)  
a
Note  
If you connected with multi-DVRs(SHR-4081N/P) through a site, Sequence will  
operate as follows.  
- In Single Mode : DVR1:1CH ➝...➝ DVR1:16CH ➝ DVR2:1CH ➝...➝ DVR1:1CH  
- In Quad Mode : DVR1:1,2,3,4CH ➝...➝ DVR2:13,14,15,16CH ➝ DVR1:1,2,3,4CH ➝ ...  
- In Nine-Split Mode : DVR1:1,2,3,4,5,6,7,8, 9CH ➝ DVR1:10,11,12,13,14,15,16CH  
➝ DVR2:1,2,3,4,5,6,7,8,9CH ➝...  
a
Click the current FAVORITE to display all the cameras  
recorded in the settting.  
b
b
You may delete all the selected FAVORITE settings or all  
the FAVORITE settings.  
c
c
You can select a new FAVORITE number and name.  
Alters FAVORITE at the selected intervals.  
●
CALLBACK Button  
d
d
- Click the CALLBACK button to activate the CALLBACK window and it is ready to  
receive a message.  
Note  
- The FAVORITE button can be activated for use only when the site is contacted.  
- The FAVORITE setup information will remain in the Config file even after the site  
contact is cancelled.  
- Upon receiving a message, Smart Viewer will automatically try to connect the DVR.  
- A message is received at the time of Video Loss, Alarm, and Motion Detection.Mode.  
- You can select if the alarm is set to ON when it receives an event message.  
- If you revise the DVR list composing the site in the Setup menu, the FAVORITE value  
will be initialized.  
10-17  
10-18  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Video Recording Button  
●
PTZ device Control Buttons  
- If you select a channel in play and click the REC button, the image will be saved  
in a file format with the extension of .dvr in a designated folder of your PC.  
*
- The name of the directory in which an image will be saved, the file name, and the  
image save length shall be set up by Setup Mode ➝ Viewer Setup.  
- The length of an image to be saved ranges from one minute to 10 minutes.  
- The saved image can be played in Local Mode of Search Mode.  
- Click the button again to stop recording. However, manual suspension is  
prohibited for 10 seconds after recording started.  
- Select a channel connected to PTZ device to control PTZ related functions.  
- PAN Left / Right  
- TILT Up / Down  
- Diagonal Control  
- The channel under PTZ control will be displayed in the center of the button.  
3
1
2
●
Audio Volume Control Button  
!@ ZOOM IN / OUT  
# POWER ZOOM : Click P to activate POWER ZOOM.  
- POWER ZOOM is a function to enlarge or reduce a video screen by touching the  
screen itself.  
- You may control Audio volume of the channel in play or set up Mute for it.  
- You can increase or decrease Audio volume by 1 between 0 and +10.  
- After POWER ZOOM is dominant, ZOOM IN / OUT will zoom in or out the video  
screen.  
●
Video Brightness/Contrast Control Button  
- POWER ZOOM Operation Procedure : Click POWER ZOOM ➝ Select ZOOM IN or  
OUT ➝ Click ZOOM IN or OUT in the video screen ➝ ZOOM IN / OUT will be  
activated in the clicked part.  
- Select the channel in play and use the control button(+,–) to adjust brightness or  
contrast of the image.  
- The default is set to +5.  
- You can increase or decrease brightness or contrast by 1 between 0 and +10.  
Note  
-
Press the Button to recover the default.  
The PAN / TILT / ZOOM function is supplied to all camera.  
But, POWER ZOOM is supported only by Samsung Smart Dome Camera, with TILT  
below 45°.  
Note  
The adjusted Audio volume, brightness, and contrast values will be saved in your PC  
and remain unchanged even if you terminate Smart Viewer and restart it.  
1
4
3
2
* OS of Windows 98 or ME do not support this Brightness/Contrast function.  
10-19  
10-20  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Self Menu Setup of PTZ device  
1
! PRESET  
- If you press the PRESET button, a window for PRESET setup pops up.  
a
If you click the current PRESET number and  
name, the camera will move accordingly.  
a
! You may set up the Function Menu in PTZ device.  
1
b
b
You can delete the selected or all PRESET  
setup values.  
c
c
! This is a Menu screen supplied by the camera itself, seen from Viewer.  
@ Use the ꢁ/ꢂ/ꢃ/ꢄbutton for the movement between menus.  
# This is a button for the role of Enter.  
You can set up a new PRESET number and  
name.  
Note  
Note  
! The PRESET function is supplied to all camera.  
The Camera Menu Setup function is supported by Samsung and Panasonic.  
You are allowed to set up no more than 20 PRESET items.  
But, the AD Protocol camera supports up to 7 PRESET items.  
Caution  
@ AUTOPAN : The camera executes this function, reciprocating between Start and End.  
# SCAN : The camera executes this function, circulating the PRESET setup positions.  
$ PATTERN : The camera executes this function, following user defined route.  
As far as SHR-4081N/P uses the PTZ device control related functions, Smart Viewer  
can not control PTZ device.  
The PTZ device control related functions are authorized with the user with Admin  
authority.  
Note  
The name of @,#, and $ functions varies depending on the camera and some  
cameras does not support any of those functions.  
- The Samsung camera supports all the functions and names.  
- The Panasonic camera supports all the functions, but with different names.  
@ SEQUENCE # AUTOPAN $ SORT  
- The PELCO camera supports all the functions, but with different names.  
@ FRAME SCAN # AUTO SCAN $ PATTERN  
- Other cameras do not support the @AUTOPAN, #SCAN, and $PATTERN  
functions.  
10-21  
10-22  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Search Mode  
8
●
The initial screen of search mode  
- The search mode is divided into the remote mode to search and play the  
SHR-4081N/P video and the local mode to play .dvr file saved in the directory  
designated by your PC.  
●
DVR(SHR-4081N/P) Selection/Change by contacting SITE  
- Same as “DVR(SHR-4081N/P)/SITE Connection” of the monitoring mode.  
*
1
3
4
●
DVR(SHR-4081N/P) Selection/Change by contacting SITE  
- Select SHR-4081N/P from the Contact list.  
2
- SHR-4081N/P turns black if contacted with the ADMIN authority and turns gray if  
contacted with the USER authority.  
- Without the ADMIN authority, search is not accessible.  
5
6
7
8
10  
11  
●
Remote Mode  
9
12  
- This mode transfers the video data recorded in SHR-4081N/P by network for the  
playback.  
- Up to 4 channels are allowed for simultaneous search and playback.  
- The video information at the time indicated by the timebar will be displayed in the  
playback screen.  
!
To change to the search mode for the remote control of video recorded in  
SHR-4081N/P  
.
@
#
To show the playback video.  
To change to the remote mode for the transmission of video recorded in  
SHR-4081N/P through network.  
When clicking, it changes to the remote mode.  
$
%
^
&
*
(
)
1
To change to the local mode for the playback of .dvr files recorded in your PC.  
*
Calendar window to select “Year/Month/Day” for search.  
To control the audio volume and video brightness/contrast.  
To change the screen split.  
Button for the Record / Convert File / Print / Setup functions.  
To control the playback of searched video.  
To display the next channel in order.  
To change the channel and DVR or renew the calendar window  
and Time Line.  
2
Timeline to display the time information of search date recorded in  
SHR-4081N/P  
.
Note  
- When connecting to the site, select a DVR to search in the camera connection list.  
- When connecting as a user, you are denied to access the search mode.  
10-23  
10-24  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Calendar Window  
@ Backup Button  
- If not playback(Stop), the video save button performs the backup function.  
- If the video data in on-line SHR-4081N/P was recorded, the date turns red.  
- If you click the date in red, the saved video information is displayed.  
- The currently selected date will be marked with a thick red box.  
- ¦¤: Moves to the previous month.  
- ‹¤: Moves to the next month.  
●
Audio Volume Control, Video Brightness/Contrast Control Buttons  
- If the save button is pressed, the window for backup pops up.  
- Set a Start/End tome for backup and select a file format to save.  
- The backup starts when the “Start” button is clicked. The backup file is saved  
according to the setting route; Setup ➞ Viewer Setup ➞ Video Recording ➞  
Video Location.  
- To stop the backup, click the “Stop” button.  
- Same as the control function of Monitoring Mode  
- Windows 98 or ME does not support this Brightness/Contrast function.  
Note  
●
Screen Split Selection Button  
Video saving in the remote mode is available only when the Play/Reverse  
Play/Fast Forward/Fast Backward button remains pressed down.  
The backup function in the remote mode is available at the Stop status.  
- Full Screen / Single / Quad / Nine-split / Sixteen split mode  
# File Converting Button  
- This function converts .dvr files into “ .jpg” files.  
*
*
Note  
9 partition and 16 partition modes cannot be used in the Remote Mode. And 4 parti-  
tion, 9 partition, and 16 partition modes cannot be used in the Local Mode.  
●
Video Save(Backup) / Video Conversion / Print / Setup  
1
2
3
4
- Click the “Open” button to select a .dvr file to be converted.  
*
- Select the JPEG Frame or AVI Video.  
! Video save button  
- If the JPEG Frame is selected, the file is converted into the “ .jpg” file by  
*
:During the playback(Play/Reverse Play/Fast Forward/Fast Backward),  
- If you select a channel in the playback and click the SAVE button, the video is  
clicking the “Start” button. The converted “ .jpg” file is saved according to the  
*
setting route Setup ➞ Viewer Setup ➞ File Converting ➞ Jpeg Location.  
saved in a file format with the extension of .dvr in a designated folder of your PC.  
*
- I f the AVI Video is selected, the file is converted into the “ .avi” file by clicking  
*
- The directory in which an image will be saved, the file name, and  
the “Start” button. The converted “ .avi” file is saved according to the setting  
*
the video length to be saved can be set at the Setup Mode  
➝
Viewer Setup.  
route Setup ➞ Viewer Setup ➞ File Converting ➞ AVI Location  
- The video length to be saved can be set from one minute to 10 minutes.  
- Click the button again to stop recording. However, manual suspension is  
prohibited for 10 seconds after recording started.  
- Press the “Start” button to convert it to a .Jpg file. Press Setup ➞ Viewer  
*
Setup ➞ File Converting to save the converted .jpg file.  
*
- Click the Stop button to pause the file conversion.  
10-25  
10-26  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
$ Print  
- This function outputs the screen zone of the playback video which is now  
being displayed.  
Note  
During play(Play/RevPlay/FF/FB), disconnection or entering both Monitoring Mode  
and Local Mode is not permitted. Click the Stop button first before conversion.  
●
Time Line  
- Displays the time information on the video data in SHR-4081N/P on the calendar  
window for the selected day.  
- The General mode indicates the 24 hour information from 0 o’clock to 24 o’clock  
while the Zoom mode indicates the time information every 2 hours.  
2
1
3
[ General Mode ]  
! The channels being displayed in Play Screen will be activated in a white  
background.  
@ Time Line : The time information on the video data recorded in SHR-4081N/P.  
# Time Bar : Displays the current time of the video image being displayed in Play Screen.  
% Setup Mode Button  
Note  
- This button pops up the setup mode window.  
Double-clicking the neighborhood of Time Bar enters Zoom In Mode.  
One column of Time Line represents an hour.  
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),  
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.  
●
Play Buttons  
2
1
2
1
5
9
3
4
8
7
6
[ Zoom In Mode ]  
! Displays the time line one hour ago.  
@ Displays the time line one hour later.  
! Play : Play  
@ Reverse Play : Reverse Play  
# Stop : Stop  
$ Fast Forward : Faster Play  
% Fast Backward : Faster Reverse Play  
^ Step Forward : Forward playback per second.  
& Step Backward : Reverse playback per second.  
* Go to First : Playback of the first image in the time Line  
( Go to Last : Playback of the latest(last) image in the time Line  
Note  
Double-clicking the neighborhood of Time Bar again enters General Mode.  
One column of Time Line represents 5 minutes.  
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),  
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.  
10-27  
10-28  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
SETUP MODE  
9
●
Next Button  
●
Description of Initial Screen  
3
- Changes a channel as the Next button does in Monitoring Mode.  
1
Note  
During Video play(Play/RevPlay/FF/FB), channel change is not available.  
●
●
Reload Button  
2
- Clicking updates the time information on the video data recorded in the calendar  
window and Time Line.  
Local Mode  
- This mode plays .dvr files recorded in the directory of your PC by the Record  
*
function.  
- You can search and play only one channel.  
- You are free for access to the user being connected to SHR-4081N/P  
- Other functions than the calendar display function are as same as those of  
Remote Mode.  
4
- The time information on Local File will be displayed at the first channel position in  
Time Line together with the file name.  
! This button is used to select items for DVR Setup, Viewer Setup, Site Setup, and  
S/W Version setup.  
@ Shows what the selected Setup item can set up in detail.  
# This button terminates the Setup window.  
: Clicking selects a file to be played in the file selection window and  
enters Local Mode.  
$ This button saves the information revised in the Setup window, remarks the  
information prior to such a revision, or terminates the Setup window.  
Note  
Only the .dvr files saved by Audio activation can be played in Local Mode.  
*
10-29  
10-30  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Setup Item Selection Button  
DVR Setup  
- Click the [DVR Setup] button for DVR Setup.  
- You can change the setup items of SHR-4081N/P Menu, being connected with  
Smart Viewer remotely.  
- DVR Setup is composed of 5 items, System, Camera/Audio, Monitoring,  
Recording, and Network.  
- This button is used for the selection of each Setup item.  
- This is composed of 4 items, DVR Setup, Viewer Setup, Site Setup, and S/W  
Version.  
- DVR Setup : DVR Setup allows you to change the remote Menu setup items of  
SHR-4081N/P.  
- Viewer Setup : Viewer Setup allows you to set up various kinds of items concern-  
ing operations of Smart Viewer.  
Note  
- Site Setup : Site Setup allows you to set up SHR-4081N/P information, that is  
SHR-4081N/P name, IP Address, ID, and Password that you contact through  
Smart Viewer or register all the registered SHR-4081Ns at a site for control.  
- S/W Version : S/W Version shows the current version of Smart Viewer, system  
requirement, and the System S/W version of on-line SHR-4081N/P and upgrades  
SHR-4081N/P System S/W remotely.  
DVR Setup is for only ADMIN.  
1
●
Save/Cancellation of Revised Information  
2
- Click the [Apply] button to save the information revised in the Setup window click  
the [Cancel] button to display the information before such a revision.  
●
Closing Setup Window  
- Click the [X] icon on the top right corner of the Setup window or the [Close]  
button to close the Setup window.  
- If more than one Setup item have been revised before you close the Setup  
window, the following message box pops up. If you press OK, the revised  
information will be saved, closing the Setup window but if you press CANCEL,  
the revised information will be flown away, closing the Setup window.  
! Among more than one on-line SHR-4081N/P, the name of SHR-4081N/P connect-  
ed in the Admin capacity will be listed. Depending on you are connected to a  
SHR-4081N/P or the site, the name of SHR-4081N/P or the name of  
SHR-4081N/P connected in the Admin. capacity among those composing the site  
will be listed. You may choose one to set up SHR-4081N/P Menu.  
@ The setup menu for selected SHR-4081N/P will be displayed.  
10-31  
10-32  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Detailed DVR Setup Items  
! System  
- Information  
Information shows the information on on-line SHR-4081N/P.  
Caution  
System Password shall be composed of number only, up to 8 digits.  
Note  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supplied to System Password input.  
- Use the BACKSPACE key to delete content.  
Note  
Default System Password is set to 4321.  
- Date/Time  
Date/Time is used to set up the information on Date, Time, Form, and Summer  
Time of on-line SHR-4081N/P.  
Note  
For the detailed items of DVR Setup, refer to Chapter 5, MENU.  
- Password  
Password determines the password for the control of SHR-4081N/P Menu or  
SHR-4081N/P key input.  
Note  
- If you change the Date/Time value, SHR-4081N/P will automatically cut the  
connection with Smart Viewer to apply a new time setup.  
- Upon completion of new time setup of SHR-4081N/P, you are permitted to resume  
connection with Smart Viewer.  
- But, Display Format or DST can be set up without disconnection.  
10-33  
10-34  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- Language  
- Remocon (Remote Control Device)  
Language sets up the language in which on-line SHR-4081N/P will be expressed  
Remocon can set up Remote Control Device fixed to SHR-4081N/P.  
Note  
Note  
Language change by SYSTEM LANGUAGE results in change of language expression  
setup of SHR-4081N/P. In short, the language setup of Smart Viewer does not  
change. Language specification to be supported is subject to change later.  
If you fix Remote Control Device to the main body of SHR-4081N/P and activate the  
setting values, Viewer will be disabled to control PTZ.  
- HDD Mode  
In HDD Mode, you may set up Writing Mode of HDD attached to SHR-4081N/P.  
10-35  
10-36  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- PTZ device  
@ Camera  
If a dome camera is connected to all channels, sets up Camera ID, Protocol,  
Baud Rate, Parity, Data Bit, Stop Bit, and Serial Mode.  
- Config.  
Config. sets up Video, Audio On/Off, Camera Title, and Screen change Time  
for each channel of on-line SHR-4081N/P.  
# Monitoring  
- Monitoring  
Monitoring sets up both Event Monitoring and OSG Display of Live Mode.  
Caution  
- Title supports English only. If you type in and apply Title in your native language,  
Warning message will pop up to ask your retyping.  
- Title shall be composed of no more than 15 texts.  
- If you leave Title blank and apply it, Warning message will pop up to ask your  
retyping.  
Note  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supplied to Title input.  
- Use the BACKSPACE key to delete content.  
10-37  
10-38  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- Alarm Rec.  
$ Recording  
Alarm Rec. sets up the information necessary for Alarm Recording.  
- Rec. Mode  
Rec. Mode sets up Live Mode decision, Video Size during recording, Quality,  
and Rate.  
NTSC  
PAL  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
Note  
Note  
Full D1(L) Video Size does not support 15ips, 10ips(NTSC) / 12.5ips, 8.33 ips(PAL)  
At least one camera should be selected in advance to be coupled with Alarm.  
- Event Rec.  
Event Rec. sets up Video Size, Quality, Rate, Pre Alarm, and Post Alarm  
values to be recorded when Event occurs.  
- Motion Rec.  
Motion Rec. sets up the information necessary for recording by Motion  
Detection.  
NTSC  
PAL  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
12.5  
Note  
Full D1(L) Video Size does not support 15ips, 10ips(NTSC) / 12.5ips, 8.33 ips(PAL)  
10-39  
10-40  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- Video Loss  
Note  
Video Loss sets up the information on how to inform the user of Video Loss of  
SHR-4081N/P.  
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not  
supplied to Network Password input.  
- Use the BACKSPACE key to delete content.  
Note  
- Default Admin Password is set to 654321.  
- Default User Password is set to 654321.  
- Configuration  
Sets up the network connection method of SHR-4081N/P.  
SHR-4081N/P supports the connection with Static IP, Dynamic IP, and ADSL(PPPoE).  
Sets up the network Bandwidth. Please adjust the bandwidth to the network con  
dition in which SHR-4081N/P is connected. Sets up IP Address, Gateway, Subnet  
Mask, and DNS. Please input both ID and password of the sub scriber in the event  
of ADSL.  
% Network  
- Password  
This sets up the password for Admin and User to let you connect with  
SHR-4081N/P through Network in Smart Viewer.  
Caution  
- Be sure to inquire the network manager before you input Network IP, Gateway,  
Subnet Mask, or DNS.  
- Both ADSL ID and Password can be input in alphabets, numbers, and symbols with-  
out discrimination as long as 40 digits and 40 digits respectively.  
Caution  
- Network Password shall be composed of no more than 8 texts.  
- If you leave Password blank and apply it, Warning message will pop up to ask your  
retyping.  
10-41  
10-42  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
● Callback  
- Sets up the Callback functions of SHR- 4081N/P.  
Note  
- Sets up the IP address and port to which SmartViewer was installed to deliver  
the Callback message in the event of Alarm, Motion Detection, or Video Loss.  
Sets up the value for retrial in the event of message delivery failure.  
- SHR-4081N/P uses 4 PORTs for TCP connection.  
- A PORT number is flexible and 4 numbers in a row will be changed in all.  
(554,555,556,557 ➝ 558,559,560,561)  
- You shall allocate the above ports for SHR-4081N/P if you want to compose a  
network by IP Router.  
Viewer Setup  
- Click the [Viewer Setup] for Viewer Setup.  
- Viewer Setup sets up various kinds of items related to Smart Viewer motions.  
- Viewer Setup is consisted of 7 items : Video Recording, File Converting,  
Sequence Time, OSD Display, Auto Connection, Callback Connection, and  
Language.  
1
2
● Translation Protocol  
4
6
3
5
- Changes the Transmission Protocol setting values. The protocol supports TCP/IP  
and UDP(Unicast, Multicast). Control Port(TCP/IP) and Port(UDP) to change the  
connection port. Multicast IP or TTL will be used for UDP(Multicast).  
7
8
! This is used for the setup of information necessary for saving the video data in  
display in .dvr file format while you are connected to SHR-4081N/P.  
*
@ This is used for the setup of information necessary for converting the file saved  
in your PC in .dvr file format into JPEG.  
*
# This is used for the setup of information necessary for Screen change Mode.  
$ This is used for the setup of information on OSD display for Smart Viewer.  
% This determines whether Smart Viewer shall be automatically connected to  
DVR(SHR-4081N/P) or Site when it begins running.  
^ This is a menu item that is designed to set the alarming time when it receives  
an event message such as an alarm, motion and/or Video loss.  
& Selects the port to allow the connection of Callback.  
*
This item is for the language setup.  
10-43  
10-44  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Video Recording  
●
Sequence Time  
! Naming  
- As long as you are connected to SHR-4081N/P in Monitoring Mode while  
Screen change is dominant, this sets up Screen change Time. The scope of  
setup ranges from 5 to 30seconds.  
- Being connected to SHR-4081N/P in Monitoring or Search Mode, you can save  
the video data in display in .dvr file format. This determines how to name .dvr  
*
*
●
OSD Display  
file format.  
- The file name depends on camera number and serial number, set to “Camera  
No. + Serial No.” or camera number, current date, and time, set to “Camera No.  
+ Date”.  
- Determines if OSD shall be displayed on each channel of Smart Viewer.  
- Whether you check “Enable” or not, OSD will appear or not. However, Audio  
icon, PTZ icon, REC icon, and Alarm/Motion event icon will not be affected by  
the OSD Display condition.  
@ Location  
4081N/P  
●
Auto Connection  
- Determines if Smart Viewer shall be automatically connected to SHR-4081N/P  
or Site as soon as it starts running.  
- If you check “Auto Connection On”, the name of SHR-4081N/P and Sites that  
are currently registered in DVR/Site List will be listed as follows and if you select  
one, it will be automatically connected to the selected SHR-4081N/P or Site as  
soon as Smart Viewer starts running.  
- As long as you are connected to SHR-4081N/P in Monitoring or Search Mode  
while recording the video data in display, this sets up a directory where .dvr file  
*
format will be saved.  
- The current default directory is “Smart Viewer Program Installed Directory  
\video\dvr”.  
# Recording Time  
- As long as you are connected to SHR-4081N/P in Monitoring or Search Mode  
while recording the video data in display, this sets up the longest recording time.  
- Time setup ranges from 1 to 10 minutes. If recording exceeds the preset time at  
Recording Time, recording will be automatically stopped.  
●
●
Callback Connection  
●
File Converting  
[JPEG]  
! Location  
- Selects the port to allow the connection of Callback.  
Event Sound  
4081N/P  
- You can convert the files saved in your PC in .dvr file format into JPEG format  
*
files then the frames composing .dvr file format will be converted into JPEG  
*
format files. Now, this designates a directory in which the converted JPEG files  
will be saved.  
- This is a menu item that is designed to set the alarming time when it receives  
an event message such as an alarm, motion and/or Video loss.  
- The current default directory is “Smart Viewer Program Installed Directory  
\frame”.  
●
Language  
- This sets a language for SmartViewer.  
10-45  
10-46  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
DVR List  
Site Setup  
- Click the [Site Setup] button for Site Setup.  
- Site Setup sets up the information on DVR(SHR-4081N/P) or Site that you want to  
contact by Smart Viewer.  
- Smart Viewer allows you to contact DVR(SHR-4081N/P) or Site registered here.  
1
3
5
- DVR List sets up the information on DVR(SHR-4081N/P) that you want to contact  
by Smart Viewer.  
- You can register a new DVR (SHR-4081N/P), delete or modify a selected DVR  
(SHR-4081N/P) from the registered list. In DVR list, the name of the registered  
DVR (SHR-4081N/P) and IP/MAC Address/URL are shown in the list.  
2
4
! User registered DVR(SHR-4081N/P) list will be displayed here.  
@ This button adds a new DVR(SHR-4081N/P) or deletes or revises the  
already-registered DVR(SHR-4081N/P).  
# User registered Site list will be displayed here.  
$ This button adds a new site or deletes or revises the already-registered Site.  
% This button adds DVR(SHR-4081N/P) selected from DVR List to the Site  
selected from Site List.  
10-47  
10-48  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- If your DVR (SHR-4081N/P) uses a static IP, select “Static IP” for Address  
Type and type in the name of the DVR (SHR-4081N/P) and the IP address.  
- Select “Port” so that it matches the port number that you’ve set in the network  
menu of DVR (SHR-4081N/P).  
- If you select “Use DDNS” in the network settings menu of DVR  
(SHR-4081N/P) or use an IP splitter to register an URL using DDNS, you can  
make connection via the URL.  
- If you want to make connection via the an URL, select “URL” for Address Type  
and type in the URL set for the DVR or IP splitter in the URL menu item.  
- Select “Port” so that it matches the port number that you’ve set in the network  
menu of DVR (SHR-4081N/P).  
- If your DVR (SHR-4081N/P) uses a dynamic IP such as in a cable modem or  
VDSL, or PPPoE for ADSL, select “MAC Address” for Address Type and type  
in the MAC address of the DVR (SHR-4081N/P).  
- Select “Port” so that it matches the port number that you’ve set in the network  
menu of DVR (SHR-4081N/P).  
10-49  
10-50  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
# Modification of Already-Registered DVR(SHR-4081N/P)  
Note  
- DVR MAC Address is written in the side label of the product.  
It is also found in System Information of DVR Menu.  
- If you select one DVR(SHR-4081N/P) in DVR List for modification and press the  
[Modify] button, the following message box will pop up. If you press [OK] button  
then, DVR(SHR-4081N/P) will be modified.  
@ Deletion of Already-Registered DVR(SHR-4081N/P)  
- If you select one DVR(SHR-4081N/P) in DVR List for deletion and press the  
[Delete] button, the following message box will pop up. If you press [OK] button  
then, DVR(SHR-4081N/P) will be deleted.  
- As long as DVR(SHR-4081N/P) for deletion is connected with the current Smart  
Viewer, the following message box will pop up and DVR(SHR-4081N/P) will not  
be deleted. Be sure to cut the connection between DVR(SHR-4081N/P) and  
Smart Viewer before you delete it.  
- As long as DVR(SHR-4081N/P) for modification is connected with the current  
Smart Viewer, the following message box will pop up and DVR(SHR-4081N/P)  
will not be modified. Be sure to cut the connection between DVR(SHR-4081N/P)  
and Smart Viewer before you modify it.  
10-51  
10-52  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Site List  
@ Deletion of Already-Registered Site or DVR(SHR-4081N/P)  
- If you select one Site or DVR(SHR-4081N/P) in Site List for deletion and  
press the [Delete] button, the following message box will pop up. If you press  
[OK] button then, either Site or DVR(SHR-4081N/P) will be deleted.  
- After being deleted, DVR(SHR-4081N/P) is still left alive in the Site composi-  
tion and so is the information on DVR(SHR-4081N/P).  
- As long as Site or DVR(SHR-4081N/P) for deletion is connected with the  
current Smart Viewer, the following message box will pop up and Site or  
DVR(SHR-4081N/P) will not be deleted. Be sure to cut the connection  
between both Site and DVR(SHR-4081N/P) and Smart Viewer before you  
delete it.  
- Site List registers multi- DVRs(SHR-4081N/P) that you want to contact at once  
by Smart Viewer at one site for control. You are allowed to register a new Site or  
delete or modify the selected Site from the registered list and add DVR  
(SHR-4081N/P) to the Site selected from Site List or delete it  
- In Site List, both the name of a registered Site and the name of DVR  
(SHR-4081N/P) composing the Site will be listed. In addition, a Site can be  
configured with up to 16 DVRs (SHR-4081N/P).  
! Site Addition  
# Modification of Already-Registered Site  
- If you press the [New] button, the following window will pop up where you can  
input the information on the new Site.  
- The information to be typed in is the Site name.  
- If you select one Site in Site List for modification and press the [Modify]  
button, the following message box will pop up where you can modify the Site  
information.  
Note  
Site may be named in both English and Korean with no more than 10 texts.  
10-53  
10-54  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
- As long as Site for modification is connected with the current Smart Viewer,  
the following message box will pop up and Site will not be modified. Be sure to  
cut the connection between Site and Smart Viewer before you modify it.  
S/W Version  
- If you press the [S/W Version] button, Smart Viewer version, system requirements,  
and the version of DVR(SHR-4081N/P) System S/W, being connected to Smart  
Viewer, if ever will be displayed.  
- You can upgrade the on-line DVR(SHR-4081N/P) System S/W remotely. You are  
authorized with S/W upgrade in an Admin capacity only. In the capacity of user or if  
you are isolated with DVR(SHR-4081N/P), your access will be denied.  
- If you select one DVR(SHR-4081N/P) and press the [Modify] button, the fol-  
lowing message box will pop up and modification to DVR(SHR-4081N/P) is  
prohibited. Modification to DVR(SHR-4081N/P) shall be done only in DVR List.  
1
2
●
DVR(SHR-4081N/P) Addition to Site  
SHR-4081N/P  
- If you press the [Add] button, DVR(SHR-4081N/P) selected from DVR List will be  
added to the Site selected from Site List. Site addition to DVR(SHR-4081N/P) set  
to ADSL is prohibited.  
- A Site can be configured with up to 16 DVRs (SHR-4081N/P), and the DVR  
(SHR-4081N/P) that configures the Site can be deleted from the Site List.  
- If you press the [Add] button unless a Site is registered in Site List, a new Site  
naming “Site [0]” as a default will be created to which DVR(SHR-4081N/P) will be  
added.  
- As long as Site for DVR(SHR-4081N/P) addition is connected with the current  
Smart Viewer, the following message box will pop up and DVR(SHR-4081N/P)  
will not be added to the Site. Be sure to cut the connection between Site and  
Smart Viewer before the addition  
! Smart Viewer Version and system requirements will be displayed.  
@ Here displays the version and name of DVR if any DVR(SHR-4081N/P) is being  
connected with Smart Viewer. You are also able to upgrade DVR  
(SHR-4081N/P) S/W by transmitting it to on-line DVR(SHR-4081N/P).  
10-55  
10-56  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Smart Viewer Version  
@ Click the following button to open the “SHR-4081N/P Firmware” file in tgz  
format.  
SHR-4081N/P Smart Viewer  
- Smart Viewer Version and system requirements will be displayed.  
DVR Version  
●
SHR-4081N/P  
SHR-4081N/P  
- DVR Version not only displays the connected DVR(SHR-4081N/P) name if any  
DVR(SHR-4081N/P) is being connected with Smart Viewer or the name of  
DVR(SHR-4081N/P) composing a site if any DVR(SHR-4081N/P) is being  
connected with the site but also displays DVR(SHR-4081N/P) S/W version.  
- Smart Viewer will be expressed in gray when disconnected from  
# Press the [Upgrade] button to transmit a file to the selected DVR  
(SHR-4081N/P) and start upgrade of DVR(SHR-4081N/P) S/W.  
DVR(SHR-4081N/P) and Status will be marked as “Not Connected”.  
- Each DVR Version has a check box, which is used for S/W Upgrade.  
$ The progress of file transmission and upgrade will be displayed at the bottom.  
●
DVR(SHR-4081N/P) S/W Upgrade  
- Smart Viewer upgrades on-line DVR(SHR-4081N/P) S/W remotely.  
Caution  
! Check a DVR(SHR-4081N/P) to be upgreaded among DVRs(SHR-4081N/P)  
on line.  
Be sure to suspend all the DVR system functions in action such as recording, MENU,  
backup, and play before you upgrade DVR(SHR-4081N/P) S/W.  
Never try to turn the DVR(SHR-4081N/P) power off during such S/W upgrade.  
S/W upgrade requires about 5 minutes.  
SHR-4081N/P  
If S/W upgrade is suspended accidentally, the previous S/W will be left intact.  
Note  
The new Firmware necessary for DVR(SHR-4081N/P) S/W upgrade shall be downloaded from  
CCTV Part in Products Section at http://www.samsung.com  
10-57  
10-58  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 11  
Backup Viewer  
11  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Introduction  
Features  
1 2  
In SHR-4081N/P, you can back up the video data by using External HDD, USB  
Memory, and CD. In the Backup Viewer, the backup image data can be searched or  
played in the PC through the CD/DVD or connecting the external HDD, USB Memory  
to the user’s PC.  
■
The video data backed up in any method among External HDD, USB Memory, and  
CD can be searched or played in your PC.  
■
Backup Viewer is optimized in the resolution of 1024 x 768.  
11-1  
11-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Backup Viewer Installation  
PC Specification(Recommendation)  
4
3
●
OS: Windows 2000, Windows XP  
●
Put the Smart Viewer Program CD in CD-ROM and open the "Backup Viewer"  
folder in the CD.  
●
Recommendation :  
- CPU Pentium 3 1GHz or higher  
- RAM 256Mb or higher  
- VGA RAM 16Mb or higher  
- Direct X 8.1 or higher  
●
Run the “Setup.exe" file.  
11-3  
11-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Click "Next".  
●
Select a folder to install Backup Viewer and click "Next".  
●
If you agree with the Backup Viewer license, click "Yes".  
●
Install the execution file and set up the system as necessary.  
11-5  
11-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Executing Backup Viewer Program  
5
●
Installation is complete. Click "Finish" to terminate the whole installation process.  
●
Double-click the Backup Viewer 1.0 icon in the background screen to execute the  
program.  
11-7  
11-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Using Backup Viewer  
Initial Screen of Backup Viewer  
7
6
●
Description  
●
Connecting  
!
Connecting means you may access and search the video data recorded in  
External HDD, USB Memory, or CD/DVD installed in your PC. Select a device that  
you wish to connect and click the Connecting button.  
@
#
$
%
●
Connecting Screen  
^
&
*
(
!
@
#
$
%
^
&
*
Terminates or minimizes the program.  
Displays the current date, weekday, and time.  
Selects a device(External HDD, USB Memory, or CD/DVD) for connection.  
Displays the image in play.  
Selects the “Year/Month/Date” that you wish to search.  
Controls Audio volume and Video brightness/contrast.  
Plays the searched images.  
These are buttons for CH change and update of the Calendar window and  
Timeline.  
(
Displays the time when a video file was recorded in External HDD, USB  
Memory, and CD/DVD for the search date.  
●
Display of Time  
- Displays the date, weekday, and time of your PC.  
11-9  
11-10  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Display of Connection  
●
Calendar Window  
- When connected to the device installed in your PC, the Connecting button  
indicates the connecting condition.  
- Click the Connecting button for disconnection.  
- The date when the video data was recorded in the current device is displayed in  
red.  
●
Display of Play Screen OSD  
- Click the red colored date to display the video information in Timeline.  
- A thick red box will be displayed in the current date.  
@
!
-
-
¦
‹
: Moves to the previous month.  
: Goes on to the next month.  
●
Audio Volume Control  
- If you play a video file with audio recorded in, you can control the autio volume or  
select Mute.  
- The audio volume can be controlled by 10 steps from 0 to +10.  
●
Brightness / Contrast  
!
@
Displays the CH number and replay time.  
Displays the Audio On/Off button.  
- You can control the brightness and constrast of the file in play.  
- The default is +5.  
- The brightness and constrast can be controlled by 10 steps from 0 to +10.  
- Press the button to return to the default.  
Note  
If the video file in play has an audio image, the Audio icon will be enabled to turn  
Audio on/off.  
: Audio Off  
: Audio On  
If the video file in play has no audio image, the Audio icon will be disabled.  
: Audio Disable  
If Audio is turned on, you can control the volume or select Mute.  
11-11  
11-12  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Timeline  
●
Play Buttons  
- Displays the time when the video image was recorded in the current device for  
the date selected from the Calendar window.  
2
1
- The General mode displays the information for 24 hours from 0 to 24 o’clock and  
the Zoom mode displays the time information every 2 hours.  
5
3
4
9
7
6
8
#
! Play  
!
@ Reverse Play  
# Stop  
@
$ Fast Forward  
[General Mode]  
% Fast Backward  
! This mode is displayed in the Play screen and the CH will be activated in the  
white background.  
@ Timeline: Displays the time information on the video data recorded in the cur-  
rent device.  
^ Step Forward : Forward by 1 second  
& Step Backward : Backward by 1 second  
* Go to Last : Plays the first image of Timeline.  
( Go to First: Plays the recent(last) image of Timeline.  
# Time Bar: Displays the current time of the video image in play.  
Note  
Note  
Double-click the Time Bar surrounding area to return to the Zoom mode.  
Each column of Timeline corresponds to one hour.  
The Timeline color changes according to the recording condition, Green(Normal),  
Red(Panic), Orange(Alarm), Blue(Motion), Yellow(Schedule), or Purple(Video Loss).  
Disconnect is not available during (Play/Reverse Play/Fast Forward/Fast Backward).  
In this case, click the Stop button.  
@
!
[Enlargement Mode]  
! Displays the timeline one hour earlier.  
@ Displays the timeline one hour later.  
Note  
Double-click the Time Bar surrounding area to return to the General mode.  
Each column of Timeline corresponds to 5 minutes.  
The Timeline color changes according to the recording condition, Green(Normal),  
Red(Panic), Orange(Alarm), Blue(Motion), Yellow(Schedule), or Purple(Video Loss).  
11-13  
11-14  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
●
Next Button  
- Displays the next channel.  
Note  
Channel change is not available in the process of (Play/Reverse Play/Fast  
Forward/Fast Backward).  
11-15  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
12  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Product Specification  
1
Item  
Specification  
32bit RISC CPU  
Remark  
Item  
Specification  
Video : MPEG4  
Remark  
CPU  
Compression  
SDRAM : 128MByte  
Flash : 16 MByte  
Embedded OS  
Audio : G.726  
Memory  
Resolution  
Quality Level  
Max Image Rate  
*ips (image  
per sec)  
Operation System  
Broadcasting  
Very High  
High  
NTSC System  
30ips(NTSC)/  
25ips(PAL)  
CIF(C)  
Input Voltage  
AC 110-220V(NTSC) / 100-230V(PAL)  
85 Watt Max  
352X240(NTSC)  
/352X288(PAL)  
Standard  
Low  
Power Comsumption  
Composite 8 Channel  
- 1.0Vp-p  
Ω Hi Z Termination  
- 75  
Resolution &  
Performance  
Very High  
High  
Half D1(N)  
15ips(NTSC)/  
12.5ips(PAL)  
Video Input  
BNC Type  
720X240(NTSC)  
Standard  
Low  
Loop Through Out 8 Channel  
- Auto Termination  
Composite 2 Channel  
- Normal Video Output 1 Channel  
- Spot Output 1 Channel  
- BNC Type  
/720X288(PAL)  
Recording  
Very High  
High  
Video  
7.5ips(NTSC)/  
6.25ips(PAL)  
Full D1(L)  
352X240(NTSC)  
Standard  
Low  
/
352X288(PAL)  
Video Output  
S-Video 1 Channel  
- 1.0Vp-p  
If the video size is CIF and the camera has  
an odd number, 30 ips is supported.  
VGA 1 Channel  
➝
Normal  
REC Key  
Mono 8 Channel  
➝
Emergency  
Schedule  
Event  
-Alarm Detection  
-Motion Detection  
-Video Loss  
PANIC Key  
Ω
Audio Input  
- -5dBm, 600  
RCA Type  
➝
Recording  
Mode  
Schedule Table  
Audio  
Mono 1 Channel  
- -6dBm  
Audio Output  
RCA Type  
-Pre & Post Recording  
Resolution Frame Rate (1Ch/8Ch)  
Resolution &  
Frame Rate  
720X480(NTSC)  
/720X576(PAL)  
30fps/240fps(NTSC)  
/25fps/200fps(PAL)  
NTSC : 1ips/3ips/5ips/7.5ips/10ips/15ips/30ips  
PAL: 1ips/2.5ips/5ips/6.25ips/8.33ips/12.5ips/25ips  
Time Laps  
Internal  
ATA HDD x 4(MAX)  
-Primary/Secondary IDE Connector  
-MAX HDD Size : 250GB x 4 = 1Tera Byte  
Single  
Quad  
Multi Screen : 6, 7, 8, 9  
PIP  
Storage  
Capacity  
IEEE1394 HDD  
Live  
-MAX 6 (Daisy chain connection)  
-MAX HDD Size : 250GB x 6 = 1.5Tera Byte  
USB HDD  
Monitoring Display Mode  
Sequence Mode  
Freeze  
External  
-MAX 1 (Not support USB Hub)  
2x Zoom  
-MAX HDD Size : 250  
Change the channel location  
(4, 6, 7, 8 PIP Division)  
12-1  
12-2  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Item  
Specification  
Remark  
Calendar  
Event  
- Normal, Panic, Schedule, Alarm, Motion,  
Search Mode  
Video Loss  
Date/Time  
HDD Specifications  
2
Go to First  
Go to Last  
Backup Data  
●
ATA HDD  
Resolution  
Decoding Performance  
Maker Capacity RPM Interface Buffer  
Series Name  
Model Name  
Remark  
Resolution &  
1Ch  
4Ch  
160GB  
200GB  
250GB  
160GB  
200GB  
250GB  
300GB  
160GB  
160GB  
200GB  
250GB  
300GB  
400GB  
160GB  
200GB  
200GB  
200GB  
200GB  
250GB  
5400 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
7200 IDE, P-ATA  
2MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
8MB  
Spinpoint  
SV1604E  
Play Back Performance  
CIF  
Half D1  
Full D1  
➝
30ips(NTSC)/25(PAL) 30 ips/1Ch  
15ips(NTSC)/12.5(PAL) 15 ips/1Ch  
7.5ips(NTSC)/6.25(PAL) 7.5 ips/1Ch  
Samsung  
Spinpoint  
SP2014N  
SP2514N  
Spinpoint  
WD Caviar SE  
WD Caviar SE  
WD Caviar SE  
WD Caviar SE  
Barracuda 7200.7  
Barracuda 7200.9  
Barracuda 7200.7  
Barracuda 7200.8  
Barracuda 7200.8  
Barracuda 7200.8  
DiamondMax 10  
DiamondMax 10  
DiamondMax 9  
DiamondMax 10  
DiamondMax 10  
DiamondMax 10  
WD 1600JB  
WD 2000JB  
WD 2500JB  
WD 3000JB  
ST3160023A  
ST3160812A  
ST3200822A  
ST3250823A  
ST3300831A  
ST3400832A  
6L160PO  
Single  
Quad  
PIP  
1Channel Decoding  
4Channel Decoding  
1Channel Decoding + 1Channel Live  
- Change the live channel.  
➝
Western  
Digital  
➝
➝
Display Mode  
Play Mode  
Multi Screen  
8 Channel live + 1Channel Decording  
Seagate  
Play, Pause, Stop, 2x Digital Zoom  
Fast Forward/Fast Reverse  
- 2x, 4x, 8x, 16x, 32x, 64x  
Still  
Jog  
Shuttle  
➝
Still  
➝
Fast Forward/Fast Reverse  
[CAUTION]  
6L200PO  
IEEE1394 External HDD  
SCSI External HDD  
USB CD/DVD Writer  
USB Flash Memory  
Input : 8 Input  
Check the HDD  
firmware version.  
(Code) : xxxx1Gxx  
6Y200PO  
Backup  
Alarm  
Maxtor  
6L200RO  
6B200PO  
7200 IDE, P-ATA 16MB  
6L250RO  
- 5mA  
Output : 4 Relay Output  
- 2A/30VDC, 0.5A/125VAC  
Reset : 1 Input  
●
External CD-RW & DVD-RW  
Maker  
Sony  
LG  
Model Name  
Interface  
Remark  
- 5mA  
DVD+RW DRX-810UL  
DVD-Multi GSA-2164D  
PX-716UF DVD+RW  
Premium-U  
USB2.0/IEEE1394  
USB2.0  
USB2.0/IEEE1394  
USB2.0  
Network  
Serial I/F  
Ethernet : 10/100 Base T, ADSL(PPPoE), DHCP  
➝
RS-485  
PTZ Device Control, Remote Control Device  
Plextor  
CPU : Pentium III, 1GHz or higher  
RAM : SDRAM 256MB or higher  
Graphic Accelerator : Graphic Memory  
32MB or higher DirectX : 8.1 or higher  
Win2000, WinXP  
PC Spec.  
Remote  
Sarotech  
FCD-524  
USB2.0/IEEE1394  
DVD -R,-RW,+RW do not support.  
External HDD Case  
Viewer  
*
●
Support OS  
Live Image Monitoring Mode  
Local File Search & Play Back Mode  
Remote File Search & Play Back Mode  
Same as Remote Viewer  
Win2000, WinXP  
Backup device(External HDD, USB Memory, CD/DVD)  
search and replay mode  
Maker  
Sarotech  
DVico  
Model Name  
Interface  
Remark  
Function  
FHD 353  
FX-2  
MHD-998  
USB2.0/IEEE1394  
USB2.0/IEEE1394  
USB2.0/IEEE1394  
http://www.sarotech.com/  
http://www.dvico.co.kr/  
http://www.makeytec.com/  
PC Spec.  
Backup  
Makeytec  
Support OS  
Viewer  
●
USB Memory  
Maker  
Function  
Remark  
Model  
FDISK V2  
MICRO X  
SHR-4081N  
: AC 120V (60Hz)  
P & C  
Stormblue  
ALTech  
Bayon  
SanDisk  
PNY  
GeekSquad  
Lexar  
LG  
Sony  
Transcend  
Kingston  
Input Voltage  
SHR-4081N(SHR-4081N/JPN) : AC 100~230V (50/60Hz)  
SHR-4081P  
: AC 100~230V (50/60Hz)  
AnyDrive  
Extreme USB Flash disk  
cruzer mini  
SHR-4081N  
SHR-4081N(SHR-4081N/JPN)  
SHR-4081P  
:
:
:
4A  
4 ~ 2A  
4 ~ 2A  
Input Current  
Attache  
Max Power Consumption  
Operation Temp.  
Preservation Temp.  
Operation Humidity  
Preservation Humidity  
Size  
MAX 200W  
0ºC ~ 40ºC  
-20ºC ~ 60ºC  
20% ~ 85% RH  
20% ~ 85% RH  
430(W) X 88(H) X 400(D)  
About 7.1Kg  
Jump Drive  
Xtick Slide  
Ultra Mini USM  
JF110  
DTI  
Weight  
The USB Memory that is recognized as CD-Rom and Mass Storage(device type) on the PC is not supported.  
*
12-3  
12-4  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Factory Default  
Outline Drawing  
4
3
This restores the Network information and preset values in SHR-4081N/P to the  
original state at the time of factory shipment.  
Factory Default will be done if you;  
- Use System / Load Factory Default in MENU or,  
- If you hold on to the Mode button in Live Mode and keep pressing the CH5  
button for 5 seconds, the system will return to the Factory default condition.  
Classification  
System Setup  
Detailed Items  
Date Format  
Factory Setup  
YYYY-MM-DD  
Time Format  
Language  
24 Hours  
Time/Date/Language  
English  
DST  
Off  
Password  
4321  
Password  
Password Lock  
Disk End Mode  
Disk End Beep  
On  
Stop  
HDD Mode Setup  
Off  
Video  
Audio  
On  
On  
Camera Config  
Title  
CAM_01 ~ CAM_8  
Auto Seq.  
ID  
5 sec  
Camera No.  
Protocol  
Baudrate  
Parity  
None  
9600  
Camera Setup  
None  
PTZ Device  
Data  
8
Stop  
1
Serial Mode  
Brightness  
Contrast  
Color  
Half Duplex  
50  
50  
50  
Screen Setup  
12-5  
12-6  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
SHR-4081N/P Smart Viewer Play  
5
Frame Specification  
NTSC  
Classification  
Detailed Items  
Duration  
Factory Setup  
FRAME  
RATE  
Viewer Screen  
Split Mode  
Event Monitoring  
Off  
VIDEO SIZE  
Date  
Time  
Title  
On  
Half D1(N)  
1 frame/sec  
15 frame/sec  
15 frame/sec  
Half D1(N)  
CIF (C)  
On  
OSG Display  
Nine-split  
Quad  
15 frame/sec  
15 frame/sec  
15 frame/sec  
CIF (C)  
On  
15  
10  
7.5  
Status  
On  
Single  
Monitoring Setup  
Spot Out Channel  
CH1  
Spot Out Event Monitor  
Monitor Out  
Off  
Composite Out  
Right Down  
5 Sec  
Nine-split  
Quad  
10 frame/sec  
10 frame/sec  
10 frame/sec  
Half D1(N)  
10 frame/sec  
10 frame/sec  
10 frame/sec  
CIF (C)  
PB Channel Position  
Multi Channel Seq.  
Mode  
Single  
On  
Nine-split  
Quad  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
Half D1(N)  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
CIF (C)  
Record Mode  
Setup  
Video Size  
CIF  
Quality  
Very High  
15ips(NTSC)/12.5ips(PAL)  
Off  
Single  
Rate  
Record Schedule  
Setup  
Continuous Recording  
Event Recording  
Nine-split  
Quad  
5 frame/sec  
5 frame/sec  
5 frame/sec  
Half D1(N)  
5 frame/sec  
5 frame/sec  
5 frame/sec  
CIF (C)  
On  
5
3
Video Size  
CIF  
Single  
Quality  
Rate  
Very High  
15ips(NTSC)/12.5ips(PAL)  
10 sec  
Event Record Mode  
Nine-split  
Quad  
3 frame/sec  
3 frame/sec  
3 frame/sec  
Half D1(N)  
3 frame/sec  
3 frame/sec  
3 frame/sec  
CIF (C)  
PreEvent  
PostEvent  
Sensor State  
Camera  
1 min  
Single  
Off  
Alarm  
Camera No.  
None  
Nine-split  
Quad  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
Event Record  
Setup  
Alarm-Out  
A.O Dwell Time  
M.D State  
Area  
1
10 sec  
Single  
Off  
All Area  
Medium  
None  
Note  
Motion Detection  
Video Loss  
Sensitivity  
Alarm-Out  
A.O Dwell Time  
Video Loss State  
Alarm-Out  
A.O Dwell Time  
The play frame specification of Smart Viewer varies on the setup of SHR-4081N/P  
Recording Rate and Video Size or the screen split mode of Smart Viewer. The above  
specification is applicable only when the main body of SHR-4081N/P is connected  
with a fast network like LAN. When the main body of SHR-4081N/P is connected  
with a slow network like ADSL, the play speed will be 0.5 Frame/sec. In addition,  
the above specification has been defined to the recommended specification of your  
PC. If your PC specification is lower than the recommended, the number of frame to  
played may diminish.  
10 sec  
Off  
None  
10 sec  
12-7  
12-8  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
Troubleshooting(FAQ)  
6
PAL  
1. The system power is dead and LED in front of the system does not operate at all.  
- Please check the power connection.  
FRAME  
RATE  
Viewer Screen  
Split Mode  
VIDEO SIZE  
- Check the power voltage.  
- If all your efforts like above end up with nothing, check or exchange the power  
supply.  
Half D1(N)  
1 frame/sec  
15 frame/sec  
15 frame/sec  
Half D1(N)  
CIF (C)  
Nine-split  
Quad  
15 frame/sec  
15 frame/sec  
15 frame/sec  
CIF (C)  
12.5  
2. Video data remains in the system but some channels displays no video data but  
turns all blue.  
Single  
- Check the image of the camera connected to the system. Improper input of  
camera input may cause this symptom.  
Nine-split  
Quad  
10 frame/sec  
10 frame/sec  
10 frame/sec  
Half D1(N)  
10 frame/sec  
10 frame/sec  
10 frame/sec  
CIF (C)  
8.33  
6.25  
- Check the camera power supply.  
- Sometimes, you see this symptom when the video data is connected with multi-  
systems and the video signal from the video data distributor in use feels weak. If  
it’s the case, you shall connect the camera images with SHR-4081N/P DVR  
directly to check or improve such a symptom.  
Single  
Nine-split  
Quad  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
Half D1(N)  
7.5 frame/sec  
7.5 frame/sec  
7.5 frame/sec  
CIF (C)  
Single  
3. The REC button in front has no effect on turning on REC LED or recording process.  
- Please check the HDD space.  
- Please check the Record Mode setup in MENU. It should be On.  
Nine-split  
Quad  
5 frame/sec  
5 frame/sec  
5 frame/sec  
Half D1(N)  
5 frame/sec  
5 frame/sec  
5 frame/sec  
CIF (C)  
5
4. All the front LEDs are in operation but the monitor remains black.  
- Video out may come out differently with the connected monitor. In short, Video  
Out is set to Composite Output but connected to VGA Input Monitor or vice  
versa. Press the "MODE" button and "0" button of front left at the same time for  
5 seconds, and press them to the time that the LED is On in sequence to change  
the Video Out mode.  
Single  
Nine-split  
Quad  
3 frame/sec  
3 frame/sec  
3 frame/sec  
Half D1(N)  
3 frame/sec  
3 frame/sec  
3 frame/sec  
CIF (C)  
2.5  
Single  
5. The front LED blinks and the logo screen repeatedly appears.  
- This symptom may be resulted from failure of HDD connection inside  
SHR-4081N/P DVR. Take off the cover and check HDD connection status. If  
HDD connection has no problem, please consult with the shop where you bought  
SHR-4081N/P DVR.  
Nine-split  
Quad  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1 frame/sec  
1
Single  
6. You cannot enter MENU by forgotten password.  
- If you forget the password, you shall reset SHR-4081N/P DVR to the values set  
at the factory. Keep pressing both the "MODE" button and the "5" button on the  
left for 5 seconds until LED lights on in the order of 1➝ 2➝ 3➝ 4➝ 5. The pass-  
word default is "4321".  
12-9  
12-10  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHR-4081N/P USER’S MANUAL  
7. The channel button does not operate in Live.  
- When you use DHCP/ADSL(PPPoE) for connection, please check if you get the  
right SHR-4081N/P DVR MAC Address.  
- If the current screen is Event Monitoring, the channel button does not operate.  
Then, press the Alarm button to terminate the current screen and select a channel.  
- If SHR-4081N/P DVR is connected to the ADSL network, please check if  
Bandwidth is set below 600 Kbps. If the Bandwidth for ADSL is set to high, the  
connection with Smart Viewer may be instable due to the heavy network load as  
the ADSL speed is low.  
8. The cursor cannot reach Start during Calendar Search.  
- Please check both the channel and the date for play are left checked. Both shall  
be checked for play with Start. The cursor cannot reach the unrecorded date.  
14. Smart Viewer in operation is disconnected.  
9. Alarm, once issued, keeps being issued though you press the front Alarm button  
- If you change time, network setup, HDD format, Default Setup, or HDD attach-  
ment or detachment for SHR-4081N/P DVR, the current Smart Viewer will be  
automatically disconnected.  
for cancellation.  
- Press the front Menu button to cancel Alarm as follows.  
1) To cancel Event Monitoring Screen : Monitoring - Event Monitoring Duration  
- Check network connection. Smart Viewer, if disconnected from Network, will try  
reconnection up to 5 times. If it remains unconnected after 5 time trial, it will  
automatically give up connection.  
Off  
2) To cancel Buzzer : Event Record - Alarm (Motion Detection/Video Loss) -  
Alarm-Out.  
- As far as SHR-4081N/P DVR is connected to the ADSL network, you may be  
disconnected from Smart Viewer when the network conditions goes bad.  
3) To cancel Event : Event Record - Alarm (Motion Detection/Video Loss) -  
State Off.  
15. The Audio icon of Smart Viewer is left inactivated in the Live mode. Setting Audio  
to On in the Camera menu of SHR-4081N/P DVR will make no difference.  
- If your PC has no Audio driver or has some problem with Audio play of an Audio  
driver, the Audio icon will be inactivated. Please check Audio driver installation  
status.  
10. No Response from the Live screen by pushing the PTZ button.  
- Press Menu ➝ Camera ➝ PTZ Device to check if the protocol and other items  
were set to PTZ Camera.  
11. When you connect several IEEE1394 armored HDDs to SHR-4081N/P DVR  
through Menu, SHR-4081N/P DVR cannot recognize all the HDDs.  
- It requires time to recognize several armored HDDs. Please try again in a few  
minutes. If retrial makes no improvement, HDD could be abnormal. Please  
exchange the HDD.  
16. When I select the channel which PTZ device is connected to in the Live mode of  
Smart Viewer, click the "Menu Control" button among PTZ setup buttons to enter  
the Function Menu mode in PTZ device, and return from the other channel, the  
PTZ related buttons have been initialized.  
- PTZ control is available in both Smart Viewer and SHR-4081N/P DVR. Other  
user might control PTZ for SHR-4081N/P DVR to terminate the PTZ device Menu  
or Auto Pan/Scan/Pattern motions while you select the other channel. This may  
cause the initialization.  
12. “CLOCK BATTERY HAS FAILED” appears on the screen.  
It appears when there is an error in the time settings of the DVR built-in clock or  
any problem related to the built-in clock happens.  
In addition, it prohibits the DVR operation to prevent loss of the data saved in the  
HDD.  
17. No Time Bar in the Search  
Please contact the product A/S department and the vendor for examination.  
- Time Line can be converted into 2 modes, General(24 Hour Display) and  
Extension(2 Hour Display). In the Extension mode, Time Bar may not be seen in  
the current time. Please enter the General mode or click the LEFT or RIGHT  
button to search Time Bar.  
13. You cannot connect to SHR-4081N/P DVR through Smart View.  
- Check if 3 Smart Viewer users are in connection with SHR-4081N/P DVR.  
SHR-4081N/P DVR allows no more than 3 users’ connection with Smart Viewer  
at a time.  
- Check the Network setup of SHR-4081N/P DVR.  
- Check Network cable connection.  
12-11  
12-12  
English  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Correct Disposal of This Product  
(Waste Electrical & Electronic Equipment)  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking shown on the product or its literature, indicates that it should not be disposed with other  
household wastes at the end of its working life. To prevent possible harm to the environment or human  
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it  
responsibly to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased this product, or their local  
government office, for details of where and how they can take this item for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract.  
This product should not be mixed with other commercial wastes for disposal.  
AB68-00520B-01 (REV. 01)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QSC Audio Stereo Amplifier SA 1350 User Guide
Radio Shack Security Camera 49 1356 User Guide
Radio Shack Telephone ET 886 User Guide
RCA Home Theater System RT2870R User Guide
RCA TV Mount RCA MAF85BKR User Guide
Samsung MP3 Player YP 90S User Guide
SanDisk Camera Accessories 80 11 00893 User Guide
Sanyo CRT Television DS13320, DS19310 User Guide
Sanyo Yard Vacuum C1822 User Guide
Sears Flat Panel Television SRTL313, SRTL315 User Guide