Samsung DVR SCR 3000P User Guide

DIGITAL VIDEO RECORDER

DVR COMBO

User’s Manual

CLASS A (For Business)

To use this product safely, have to read “Important Safety Introductions”, and then

be well aware of the contents.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Important Safety Instructions

Contents

V. Viewing the VCR Menu

iii

1. VCR Menus

5-1

5-3

2. Manual Archive

3. Timer Archive

4. Archive Setup

5. Archive Check

5-8

5-11

5-13

I. Summary

1. Introduction

1-1

1-2

1-3

1-7

1-8

1-9

2. Features

VI. Record

3. Name and Function of Each Part

4. Introduction to the Remote Control

5. Checking the Package Contents

6. Attaching/Deta ching HDD

6-1

6-3

6-4

6-5

1. Basic Record

2. Record Lock

3. Alarm Record

4. Reservation Record

II. Connection with Other Devices

1. Connection to External Devices

2. Connection with Multiplexer

VII. Retrieval and Playback

1. Search Menus

2-1

2-2

2-3

2-4

7-1

7-3

7-4

7-5

7-6

2. Retrieval by Date and Time

3. Recorded Data List View

4. Alarm Record Retrieval

6. Searching Motion Detection

Recordings

3. System Connection for Alarm Recording

4. Connection with PC for Use

III. Basic Method to use

1. Booting the System

3-1

3-3

7-7

7-8

7. Pb Channel Setup

2. Basic Screen Viewing

8. System Indication

7-11

7-13

7-15

9. Basic Playback

IV. DVR Menus

10. VCR Playback

4-1

4-6

1. Menu View

11. Searching the Backed-up Data

(VISS)

2. Setting of Date, Time and Screen

3. Record Setup

4-7

7-16

12. Playing Back a Section Repeatedly

4-10

4-14

4-15

4-17

4. Alarm Record Setup

5. Reservation Timer Setup

6. System Setup

VIII. Others

1. Product Standards

8-1

8-2

7. Communication Setup

2. Appearance Drawing

Appendix

9-1

1. Check Points before Call Service

Center

9-3

2. Q & A

Download from Www.Somanuals.com. All Manuals Search And Download.

I. Summary

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Introduction

Features

1 2

DVR COMBO is DVR system using both hard disk drive and VCR tape simultaneous-

ly. Record TV reception into hard disk drive while also recording only desired program

to VCR tape. Recorded VCR tape can be viewed with residential VCR.

■

Data on your hard disk can easily be backed up onto video tapes.

■ Only particular channels of the multiplexer can be backed up

■ Playback of particular channels can be protected

■

Picture quality can be adjusted to 4 different levels.

■ Very High, High, Normal, and Low

DVR COMBO can play while recording sound and image simultaneously. The system

and camera can be monitored and controlled from a remote PC. Together with

Samsung Multiplexer, the system can backup only desired image per each channel.

The number of recording fields per second can be adjusted.

■ NTSC : 0.50 ~ 60 fields/s

■ PAL : 0.50~50 fields/s

■

Recording and playback can be performed simultaneously.

Video and audio can be recorded simultaneously.

It has a timer recording function you can set just like you would your VCR.

Recording can be triggered by alarm sensor input.

It has a motion detection capability that can raise an alarm or start recording

when motion is detected.

■

It can be used in conjunction with a multiplexer. SAMSUNG SDM-160(P), 090(P)

Multiplexer SOM-080(N/P), SMO-150/210(TRN/TRP)

■

It offers various playback speeds.

■ 1/5, 1/2, 1, 2, 5, 10, 20 baud rate (forward, backward)

It has convenient search functions.

■ Date & Time Search, Record Event Search, Alarm Event Search, and Motion Event

■ VISS Search

■

The Remote Control allows for convenient operation.

Remote monitoring and controlling are possible via LAN connection.

■ Network Interface : Ethernet (10 BaseT)

■ Protocol : TCP/IP

■ Web Server : Screen capture and remote monitoring using a viewer program installed on a PC

■

The system boots up automatically and can start recording when power is

restored following a power outage during Record mode.

The system can be controlled remotely through serial communication ports.

■ 1 RS-232 port

■ 2 RS-485 ports (up to 32 nodes)

■

Control of camera PAN/TILT/ZOOM by the LAN viewer program via RS-485

■

Recording status, remaining hard disk space, and in particular current play-

back position are displayed in bar format.

■

A removable hard drive rack allows you to easily replace hard disk drives.

Cameras can be controlled and channels can be selected using the Remote

Viewer program.

(Applicable only to Samsung products : SCC-641/SCC-643(N/P) Cameras, SCC-

421(N/P) Series Camera(C4201, C4203, C4301 and C4303), and SDM-160(P),

090(P) Multiplexer SOM-080(N/P), SMO-150/210(TRN/TRP)

1-1

1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Name and Function of Each Part

Front View

POWER

ALARM

Name

Function

REC REC LOCK

VCR

SEARCH MENU

LAN

CHECK ARCHIVE

Displays a list of recorded data and allows you to easily

search through the recorded data.

Displays the menu items. Use this also to exit the

submenu and return to the menu at the next highest

level. If the VCR LED is off, the DVR MAIN

MENU will be displayed and if it is on, the VCR

MAIN MENU will be displayed.

10 11 12 13 14 15 16 17 18

Name

Function

The LEFT arrow button moves the cursor to the left.

This button also works as the REW button during play-

back. While in Pause mode, pressing this button will

make the video reverse one frame at a time.

Hard Drive

The removable hard drive rack into which your hard

drive could be installed.

LEFT/REW

Rack

The hard drive status indicating LED. It indicates

power status and access to the hard drive.

HDD LED

Use this to accept the selected menu item or to accept

the changed value.

ENTER

Remote Control

Sensor

Receives signals from the remote control unit.

Allows you to lock the hard drive rack in place.

The DOWN arrow button moves the cursor down one

position or lowers a value. This button also works as the

STOP button during playback or recording.

Hard Drive

Rack Lock

DOWN/STOP

POWER

POWER LED Indicates that power is on.

The RIGHT arrow button moves the cursor to the right.

This button also works as the FF button during play-

back. While in Pause mode, pressing this button will

make the video advance one frame at a time.

Indicates system status.

ALARM

LAN

■

ALARM : Indicates alarm status.

RIGHT/FF

■■

LAN : Indicates when the system is connected to a

STATUS LED

PC via LAN.

CHECK

■

CHECK : Indicates any abnormal occurrence

dur ing the system operation.

ARCHIVE : Indicates the video tape backup.

ARCHIVE

The UP arrow button moves the cursor up one position

or raises a value. This button also works as the PLAY

button and the button to pause playback or view still

images.

UP/PLAY/

STILL

REC

RECORD

Records live images.

REC LOCK

Locks all keys during recording to prevent accidental

operation of the unit.

REC LOCK

EJECT

Push this button to eject the video tape.

VCR

If the VCR LED is on, the system is in VCR mode

and if it is off, the system is in DVR mode.

The cassette holder into which a video tape could be

inserted.

VCR

VIDEO DECK

1-3

1-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Back View

OUT

Name

Function

POWER

Power On/Off switch.

The inlet for connecting the power cord.

AC IN

FAN

NTSC (AC 110 ~ 240V, 60 Hz) PAL (AC 220V, 50Hz)

Fan

Name

Function

RCA type audio input/output connectors.

Audio In/Out

Dip switches for setting the system ID, serial communication,

and termination.

MODE

LAN

Connector for LAN cable connection.

■

1~5 : System ID (1 : Least Significant Bit, 5 : Most

■

ALARM IN: In N.C. (Normally Closed) mode, the system rec

External

Input/Output

Ports

Significant Bit) (Push the dip switch up to set it to

Off (0) and push it down to set it to On (1).)

ognizes an alarm condition when a high (5V) signal is input for

longer than 0.5 second. In N.O. (Normally Open) mode, the

system recognizes an alarm condition when a low (0V) signal

is input for longer than 0.5 second.

■

: Not Used

■

: Termination On/Off (Use this to set the last system

in a series of serially connected systems to ON or

OFF.) (Push the dip switch up to set it to OFF and

push it down to set it to ON.)

■

ALARM RESET: If a low (0V) signal is input for longer 0.5

second, Alarm mode will be cancelled..

■

: Not Used

ALARM OUT: A high (5V) signal will be output during alarm

recording.

A serial port for remote control.

■

TRIGGER OUT: This signal is for switching the multiplexer's

recording output screen.

REC IN: The system begins recording if a low (0V) signal is

input for longer than 0.5 second.

DISK END: If DISK END MODE in the RECORD MODE

SETUP menu is set to STOP, a low (0V) signal will be output for

about 1 second when the hard drive becomes full during recording.

RS485 PORT

RS232 PORT

■

BNC style connectors for composite video input/output.

S-VIDEO input/output connectors.

Video In/Out

Connectors

1-6

1-5

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Introduction to the Remote Control

Checking the Package Contents

When purchasing product, first remove packing and put it on a flat floor or at a place to use it.

Then, ensure all following contents are included:

■ Main Unit

Use to remove the video tape

Adjusts the VCR's playback

Records live video

Numeric keys

■ User's Guide

screen.

■ Power Cord (1)

p 7-13

Plays the tape at slow speed.

Adjusts the VCR's playback screen.

■ Remote Monitoring Program Installation CD-ROM

■ Remote Control

Press and hold the SLOW + button

to gradually increase the playback

Plays the tape at slow speed.

Press and hold the SLOW - button

to gradually decrease the

playback speed.

speed.

p 7-13

■ Battery (AAA size) (2)

Plays back the AB section

repeatedly during DVR/VCR

■ Removable Hard Drive Rack Key (2) (Including screw)

playback.

p 7-16

Use to check the video

tape backup.

p 5-13

DIRECT ARCHIVE

p 5-8

Use to view live screen during VCR

playback.

Takes you to DVR INPUT for

selecting a DVR input signal.

p 4-7

Use to fast forward or to sequentially

view still frames during DVR/VCR

playback. p 7-13

Use to rewind or to sequentially view

still frames in reverse order during

POWER

p 7-13

DVR/VCR playback.

Plays back DVR/VCR's recorded

data.Temporarily stops during play-

back.

REC REC LOCK

VCR

SEARCH MENU

ALARM

LAN

CHECK ARCHIVE

Stops DVR/VCR playback or

recording

Displays the recorded data

list and the system status.

Displays menu items. Use this also

to exit the submenu and return to

the menu at the next highest level.

p 7

Takes you to SYSTEM INDICATION

for checking the system health

Selects VCR mode and DVR mode.

status.

p 7-8

ꢀ,❷,➛,❿

directional keys

Turns OFF only the events that

currently producing buzzer output.

Use to select a menu item or to

accept the changed value.

SCR-3000

Automatically searches the

data backed up on to the

video tape.

p 7-15

p 5-11 Takes you to VCR SPEED for

selecting a VCR recording speed.

Locks all keys during recording to

prevent accidental operation of the

unit.

Plays the tape at 2x speed.

p 7-13

Plays the tape at slow speed.

Caution

The above items are subject to change without prior notice to improve product

performance or functionality.

1-7

1-8

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Attaching/Detaching HDD

Mounting HDD

H.D.D.

POWER

ALARM

REC REC LOCK

VCR

SEAR

H.D.D.

LAN

CHECK ARCHIVE

Lift up

POWER

ALARM

REC REC LOCK

VCR

SEA

LAN

CHECK ARCHIVE

6. Lock the hard drive rack with the

key, and then turn on the power.

5. Lift up the rack's front handle and push

the rack into the main unit. Once the

hard drive rack is fully inserted into the

main unit, lower the front handle to

secure it

Lift up

1. First, open the hard drive rack cover

on the front of the main unit. Next,

open the lock on the front of the rack

with the key.

2. Remove the hard drive rack from the

main unit by lifting up the handle on

the front of the rack and pulling

straight out.

Note

When installing a HDD into the hard drive rack, be sure to set the HDD as Master

mode. Otherwise, the system will not recognize the HDD. For instructions on how to

set the HDD as Master mode, please refer to the HDD's manual. For example, for a

Samsung Spinpoint V80 HDD, set the mode as follows:

H.D.D.

Master Mode

Caution

3. Connect the removable rack's

data cable and power cord to

your hard drive.

4. Slide your hard drive into the

removable rack and fasten with

screws.

Be sure to lock the hard drive rack in place for normal operation of the system. Unless

the hard drive rack is locked, the system cannot recognize your hard drive.

When removing the hard drive rack, be sure to wait until your hard drive's power LED

goes off. When replacing your hard drive with another one, be sure to turn off the sys-

tem's power. If you replace your hard drive with the power on, your hard drive may

malfunction or be damaged.

If you want to use a hard drive from another machine, be sure to format it from a PC

before using it. The system may not work normally if you use it without formatting it

first. Hard disk drives recommended for use with the DVR COMBO are Samsung

Spinpoint SV0802N and SEAGATE Barracuda 7200.7 80G.

1-9

1-10

Download from Www.Somanuals.com. All Manuals Search And Download.

II. Connection with

Other Devices

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Connection with Multiplexer

Connection to External Devices

1 2

(e.g. connection to SDM-160)

CAMERA

SIREN

CAMERA

MICRO PHONE

MONITOR

OUT

DVR COMBO DIGITAL VIDEO RECODER

AC IN

OUT

SDM-160 DIGITAL MULTIPLEXER

OUT

■

SDM-160 is a Multiplexer for NTSC, and SDM-160P is a Multiplexer for PAL.

Connect this unit’s video signal input jack to the video signal output jack of SDM-160 and

connect this unit’s video signal output jack to the video signal input jack of SDM-160.

Connect the alarm output jack (ALARM OUT) of SDM-160 to this unit’s alarm input jack

(ALARM IN), and connect the VTI jack of SDM-160 to this unit’s trigger output jack

(TRIGGER OUT).

LAN

■

VIDEO/AUDIO OUT

■

Connect both GND terminals together.

For details on the functions of SDM-160, please refer to the user’s guide of SDM-160.

(NTSC/PAL MONITOR)

Caution

■

This unit can be connected to external devices such as a camera for video signal input, a

microphone for audio signal input, and an NTSC or PAL monitor for video and audio signal

output.

- Be sure to connect the trigger output terminal (TRIGGER OUT) of this unit to

the Multiplexer. Otherwise, a normal recording cannot be made.

(For the connection method, please refer to the user’s guide for the Multiplexer

you want to use.)

■

It can be connected to external devices such as an alarm according to the user’s request.

It can be connected to a PC through a LAN or Serial connection for remote control.

- Set up the Multiplexer so that the selection of video signals is controlled by the

Trigger Pulse in when the system’s field recording rate is set from 0.5 ~ 15 FPS

(Fields Per Second) for NTSC signals, or 0.5~12.5 FPS for PAL signals.

(For settings related to the recording field rate, please refer to "(4) PICTURE

RATE" on page 4-7.)

Caution

- Only half of a video channel may not be recorded, depending on the type of

multiplexer, when the system’s field recording rate is 30 FPS (for NTSC) or 25

FPS (for PAL). In this case, set the output mode of the multiplexer to Frame-

Mode or adjust the field recording rate of the DVR to 60 FPS (for NTSC) or 50

FPS (for PAL).

– A monitor capable of displaying an NTSC or PAL video signal must be used with

this unit. An ordinary computer monitor cannot be used.

2-1

2-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

System Connection for Alarm Recording

Connection with PC for Use

3 4

Connection with RS-232C

A. Communication Method

■ Data Code: ASCII Code

■ Protocol: 8 bit Data, 1 Stop bit, None Parity

■ Transmission speed: 4800, 9600, 19200, 38400, 115200 bps

B. RS-232C terminal (D-SUB 9 Pin) and Pin specifications

ALARM IN

GND

ALARM RESET

ALARM OUT

GND

TRIGGER IN

ALARM IN

ALARM CANCEL

ALARM OUT

Pin No

Pin Specifications

TRIGGER OUT

GND

TXD (Transmitted Data)

RXD (Received Data)

SG (Signal Ground)

NO Connection

REC IN

DISK END

GND

1, 4, 6~9

■

Alarm recording is a function for recording the input video when an alarm signal is input

while a device with alarm output is connected to this unit.

Connect to the corresponding terminals, as the numbers may be different for external

devices.

For external devices, if the alarm input (ALARM INPUT) and alarm cancel (ALARM

CANCEL) are not available, you can leave them unconnected.

2-3

2-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

D. Code value by key

Connection with RS-485

Response

(Byte 5)

If you control cameras, remote control is allowed through connection with RS-485 (up to

1.2km).

Function

Byte 1

Byte 2

Byte 3

Byte 4 Byte 5 Byte 6, 7, 8

Byte 9

[SET COMMAND]

A. Communication method

RECORD

REC LOCK

VCR

0xA0

Src.Addr Dest.Addr.

0x1A

0x0B

0x0A

0x3D

0x02

0x01

0x35

0x06

0x07

0x08

0x09

0x04

0x05

0x3E

0xFF

Check Sum

Byte 5

■ Data transmission method: Start-Stop Asynchronized Serial Interface

■ Protocol: 8 bit Data, 1 Stop bit, None Parity

■ Transmission speed: 4800, 9600, 19200, 38400, 115200 bps

ENTER

LEFT

B. RS-485 terminal and Pin specifications

RIGHT

STOP

RIGHT

DATA +

DOWN

EJECT

DATA -

DATA +

C. Data Format (Samsung Protocol)

E. Others

(

) : Byte numbers

9 Byte Fixed

■ Above data format and transmission speed may be changed depending on future

development conditions.

Start Code (A0H)

(1)

Start Addr.

(1)

Target Addr.

(1)

Command

(5)

Check Sum

(1)

■ PC operates as Master, and Target Set as Slave in transmission/reception of data.

■ No status other than Set Key Function should be received.

(Some delay can be happen due to communication speed).

Data Byte

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Byte 8

Byte 9

Type

Contents

Remarks

Start Code

Sender Addr.

Target Addr.

0xA0

Transmission Address

Reception Address

Only Image Recorder Command

Key Function

Start of Data Packet

Source Range (0x00 ~ 0xFF)

Destination Range (0x00 ~ 0xFF)

0x0A

Range (0x01 ~ 0xFF)

Command

0xFF

Check Sum

Lower byte of (0xFFFF - (values adding Byte 2 ~ Byte 8))

2-5

2-6

Download from Www.Somanuals.com. All Manuals Search And Download.

III. Basic Method

to use

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Booting the System

Power On

There is a power switch on the upper right hand side behind the system. Pull the power

switch up to boot the system. Then, the POWER LED ( ^POWER) on front of the system is

turned on, a blue screen with the following message will appear and the system is booted.

Recognizing incoming video signal

The SCR-3000N/SSC-Dual system only recognizes NTSC signal inputs only when booting. The

system will not recognize PAL signals, and a disrupted output would result in a PAL signal were

connected to the system’s input. When this occurs, power-down the system and connect an NTSC

signal to the input. The system then initializes to NTSC signals on power-up. On the other hand, the

SCR-3000P system only recognizes PAL signal inputs. Please connect the video signals appropriate

for each model.

LOAD CONFIGURATION...

If no HDD is installed or if the system is turned on while the hard drive rack is unlocked, the system

will boot up and the Live screen will appear, but the system will not be able to find the HDD. As

shown below, the HDD icon ( ),

will not appear.

When booting is finished, the following Live screen will appear.

2003-06-01 12:00:00

Power Off

Push the power switch down in order to turn off the system.

When the system power is turned off during recording, recording will be resumed next time the

system power is turned on and booting is complete.

3-1

3-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Basic Screen Viewing

Viewing Full Screen

Here comes the description of all the icons and status in the screen.

2003-06-25 04:30:00

❿ꢁ

2003-06-24 00:23:44

If system is in the recording state

Live Screen state.

icon will blink. However, it does not blink in the

The upper pointer shows the relative location of the recorded data being stored inside

the hard disk and the lower pointer shows the relative location of the data currently

being played back. The following pointer will be hidden in the general live screen and

recording screen.

If the system is in the recording state due to alarm,

icon continually blinks.

While the data recorded by ALARM RECORD is playing, an icon will appear in

front of the recording date and time of the data.

icon appears. In this state,

You can change the above system status display position. The user will mark the position in the

top left and right corner. (Select LEFT or RIGHT in STATUS POSITION of the

CLOCK/DISPLAY MODE SET UP menu. Please refer to Page 4-6 for the details)

If the system is in the recording state due to Motion Detection,

In this state, icon continually blinks.

icon appears.

While the data recorded by Motion Detection playing, an

of the recording date and time of the data.

icon will appear in front

It shows the current date and time as configured by the system.

2003-06-25 04:30:00

You can change the display position of date and time. You shall designate the position

If the system is in the recording state due to the timer,

While the data recorded by Timer record playing, an

the recording date and time of the data.

icon appears.

icon will appear in front of

in the top right or left corner by yourself. (Just choose LEFT or RIGHT in the

CLOCK/DISPLAY MODE SETUP menu. Please refer to Page 4-6 for the details)

❿

If the system is in the playback mode, icon appears. And if the system is in the

If the system in the recording lock state,

icon appears.

pause state, it changes to this icon ■■. In addition, stored data can be played back at

various speeds; when played in the forward direction at speeds other than the normal

Appears when the system is connected to the PC's remote monitoring program via LAN.

Indicates whether a HDD is installed or whether the hard drive rack is locked.

Indicates whether a video tape is in the video deck.

❿

speed, the speed is shown on the right side of the icon and if it is played in the

➛ꢁ

reverse direction at speeds other than the normal speed, icon appears and the right

➛ꢁ

side of this icon shows the speed. Possible speeds in the system for forward and

reverse directions are 1/5, 1/2, 1, 2, 5, 10, 20 times normal speed.

Indicates whether the data from the current HDD is being backed up on to a video tape.

2003-06-24 00:23:44

It shows the recorded date and time of the data currently being played back.

You can change the recording date and time display position. The user will mark the

position in the bottom left and right corner. (Select LEFT or RIGHT in TIME MARK

POSITION of the RECORD MODE SET UP menu. Please refer to Page 4-8 for the

details.)

99%

Displays the amount of free space remaining on the HDD in percent (%). However,

this will be displayed only if DISK END MODE is set to STOP and not to OVER-

WRITE.

For details, please refer to pages 4-8.

3-3

3-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Viewing Screen during recording

Live Screen Viewing

The normal recording screen looks like this.

The normal Live screen looks like this.

2003-06-25 04:30:00

If system is in the recording state

Live Screen state.

icon will blink. However, it does not blink in the

If the system is executing the recording function,

icon blinks.

If the system is in the recording state due to alarm,

icon continually blinks.

icon appears. In this state,

Indicates whether a HDD is installed or whether the hard drive rack is locked.

It shows the relative location of the recorded data inside the hard disk.

It shows the current date and time as configured by the system.

If the system is in the recording state due to Motion Detection,

In this state, icon continually blinks.

icon appears.

2003-06-25 04:30:00

If the system is in the recording state due to the timer,

If the system in the recording lock state, icon appears.

icon appears.

It occurs when the system is connected to remote viewer program through the LAN.

Indicates whether a HDD is installed or whether the hard drive rack is locked.

It shows the relative location of the recorded data inside the hard disk.

2003-06-25 04:30:00

Indicates the current date and time of the system.

The position of the date and time display on the screen can be changed. The date and

time can be displayed either at the top left or top right of the screen.

(Select either LEFT or RIGHT in DATE & TIME DISPLAY of the CLOCK/DISPLAY

MODE SETUP menu. For details, see page 4-6.)

3-5

3-6

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Playback screen Viewing

The normal Playback screen looks like this.

❿ꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁ

2003-06-24 00:23:44

The upper pointer shows the relative location of the recorded data being stored inside

the hard disk and the lower pointer shows the relative location of the data currently

being played back.

❿

If the system is in the playback mode, ❿ icon appears. And if the system is in the

pause state, it changes to this icon ■■. In addition, stored data can be played back at

various speeds; when played in the forward direction at speeds other than the normal

speed, the speed is shown on the right side of the❿ icon and if it is played in the

reverse direction at speeds other than the normal speed,➛ꢁicon appears and the right

side of this ➛ꢁicon shows the speed. Possible speeds in the system for forward and

reverse directions are 1/5, 1/2, 1, 2, 5, 10, 20 times normal speed.

2003-06-24 00:23:44

It shows the recorded date and time of the data currently being played back.

3-7

Download from Www.Somanuals.com. All Manuals Search And Download.

IV. DVR Menus

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Menu View

Entering the DVR MAIN MENU

Move to Parent Menu or Menu End

Press the MENU (

) button. Then the following screen should appear.

Press the MENU(

menu.

) button to move to the parent menu from the lower mode or end the

MAIN MENU(DVR)

CLOCK/DISPLAY MODE SETUP

RECORD MODE SETUP

ALARM RECORD SETUP

TIMER RECORD SETUP

SYSTEM SETUP

COMMUNICATION SETUP

MOVE=[ꢀ

/❷] SELECT=[

] EXIT=[MENU]

Note

- Make sure that the VCR LED is off before pressing the MENU button. If the VCR

button had been pressed, the VCR MAIN MENU will be displayed.

- You can go into the menu only if the system is in Live Screen mode. If the system is

in Record or Play mode, you cannot go into the menu. To go into the menu, first

stop recording or playback.

Selecting a Menu Item

Use the UP(ꢀ) and DOWN(❷) buttons to select the menu item you want. A highlighted cur-

sor should appear over the selected item. Next, press the ENTER(

) button to accept the

choice. Settings will be displayed on the left and their values will be displayed on the right.

Changing the Settings

■ Use the UP(ꢀ) and DOWN(❷) buttons to select the setting you want to change.

■ Press the ENTER(

■ Use the UP(^ꢀ) and DOWN(❷) buttons to change the value.

■ Press the ENTER( ) button to accept the choice.

■ When you press the ENTER button, some setting fields are toggled.

) button to accept the choice.

4-1

4-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

■ Similarly, press the UP(ꢀ) or DOWN(❷) button so current minute is displayed.

Then if pressing the LEFT(➛) or RIGHT(❿) button, the cursor is changed so hour or

second is changed. For example, press the RIGHT(❿) button to change seconds and

setup by pressing the UP(^ꢀ) or DOWN(❷) button so current second is displayed.

Example of menu setting (in case of changing time)

■ Press the MENU button and then press the ENTER(

) button when the cursor

points out the CLOCK/DISPLAY MODE SETUP. Then following screen appears.

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

12:00:00

DATE DISPLAY TYPE

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

STATUS DISPLAY

STATUS POSITION

YYYY-MM-DD

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

09:34:00

LEFT

DATE DISPLAY TYPE

YYYY-MM-DD

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

STATUS DISPLAY

STATUS POSITION

LEFT

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

■ Press the DOWN(❷) button so the cursor points out TIME.

Then if pressing the ENTER(

changed.

) button, the cursor is changed so hour may be

■ The cursor is changed as follows if pressing the ENTER(

) button after setting al

hours. You may change other settings by pressing the LEFT(➛) or RIGHT(❿) button.

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

12:00:00

DATE DISPLAY TYPE

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

STATUS DISPLAY

STATUS POSITION

YYYY-MM-DD

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

09:34:27

LEFT

DATE DISPLAY TYPE

YYYY-MM-DD

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

STATUS DISPLAY

STATUS POSITION

LEFT

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

■ Press the UP(ꢀ) or DOWN(❷) button so current time (hour) is displayed.

❿

Then if pressing the RIGHT( ) button, the cursor is changed so minute may be

changed.

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

09:00:00

DATE DISPLAY TYPE

YYYY-MM-DD

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

STATUS DISPLAY

STATUS POSITION

LEFT

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

4-3

4-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Each menu item

Setting of Date, Time and Screen

The following illustrates the intial setting of the CLOCK/DISPLAY MODE SETUP menu.

■ CLOCK/DISPLAY MODE SETUP

■ RECORD MODE SETUP

CLOCK/DISPLAY MODE SETUP

RECORD MODE SETUP

CLOCK/DISPLAY MODE SETUP

DATE

TIME

2003-06-01 SUN

12:00:00

DVR INPUT

VIDEO-IN

HIGH

30.00FPS

OVERWRITE

DATE

TIME

2003-06-01 SUN

12:00:00

AUDIO RECORD

PICTURE QUALITY

PICTURE RATE

DISK END MODE

DISK END BUZZER

RECORD TIME MARK

DATE DISPLAY TYPE

YYYY-MM-DD

DATE DISPLAY TYPE

YYYY-MM-DD

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

DATE & TIME DISPLAY ON

DATE & TIME POSITION RIGHT

STATUS DISPLAY

STATUS POSITION

LEFT

STATUS DISPLAY

STATUS POSITION

LEFT

TIME MARK POSITION RIGHT

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

■ DATE

Set the current date.

■ ALARM RECORD SETUP

■ TIMER RECORD SETUP

■ TIME

Time can be entered in the form of 24 hours.

TIMER RECORD SETUP

ALARM RECORD SETUP

TIMER

DAY

START

END

FIELD RATE

ALARM SIGNAL DETECTION

ALARM SIGNAL POLARITY

ALARM BUZZER

OFF

N.O.

10 SECOND

2 SECOND

OFF

30.0 FPS

OFF

--- --:-- --:--

--.--

Caution

MAIN ALARM TIME

Be sure to set the date and time to the current date and time.

PRE ALARM TIME LIMIT

POST ALARM TIME LIMIT

MAIN ALARM PICTURE RATE

MOTION DETECTION

■ DATE DISPLAY TYPE

SET AREA & SENSITIVITY

There are 3 date forms to be displayed. You can set in a convenient manner to see.

➛

❿

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

[YYYY-MM-DD/DD-MM-YYYY/MM-DD-YYYY]

■ DATE & TIME DISPLAY

Set to ON to display the date and time on the screen, or set to OFF to not display them.

[ON/OFF]

■ SYSTEM SETUP

■ COMMUNICATION SETUP

■ DATE & TIME POSITION

COMMUNICATION SETUP

SYSTEM SETUP

Set the location on the screen where the date and time will be displayed. Set to LEFT to

display it on the top left of the screen, or set to RIGHT to display it on the top right of the

screen. [LEFT/RIGHT]

BAUD RATE

NETWORK ACCESS

IP ADDRESS

115,200

0. 0. 0. 0

****

PASSWORD

PASSWORD LOCK

HDD ERASE

FACTORY RESET

MENU SCREEN

LANGUAGE

IR REMOCON

MULTIPLEXER

****

OFF

DARK GRAY

ENGLISH

OFF

GATEWAY

SUBNET MASK

NETWORK USER ID

NETWORK USER PWD

PAN/TILT TYPE

****

SCC-421

■ STATUS DISPLAY

WITHOUT

Set to ON to display the system status, such as recording, system lock, to remaining HDD

capacity, and playback information when playing the recorded video; or set to OFF to not

display them. [ON/OFF]

MULTIPLEXER SELECT SAMSUNG SDM-160

➛

❿

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

MOVE=[ꢀ/❷/ / ] SELECT=[

] EXIT=[MENU]

■ STATUS POSITION

Caution

Set the location on the screen where the system status will be displayed. Set to LEFT to

display it on the top left of the screen, or set to RIGHT to display it on the top right of the

screen. [LEFT/RIGHT]

Upon shipment from the factory, the values of the menu are set as follows.

4-5

4-6

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Record Setup

The following illustrates the intial setting of the RECORD MODE SETUP menu.

■ DISK END MODE

■■If you select STOP, recording will stop when you consume the full HDD space.

■■Setting this to OVERWRITE will continue to record the current data by overwriting the

previous data. The relative positions where the recorded data are being stored in the HDD

will be indicated on the screen in a bar format. If the DISK END MODE is set to STOP,

in addition, the remaining HDD capacity will be indicated in percentage (%).

[OVERWRITE/STOP]

RECORD MODE SETUP

DVR INPUT

VIDEO-IN

HIGH

30.00FPS

OVERWRITE

AUDIO RECORD

PICTURE QUALITY

PICTURE RATE

DISK END MODE

DISK END BUZZER

RECORD TIME MARK

TIME MARK POSITION RIGHT

■ DISK END BUZZER

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

If set to ON, the Buzzer will sound when the HDD is full during the recording; if set to

OFF, the Buzzer will not sound. DISK END MODE needs to be set to STOP for activation.

[ON/OFF]

■ DVR INPUT

Set the 3 types of Video Input signals going into the DVR.VIDEO-IN is the input signal

going into the BNC Video Jack, S-VIDEO is the signal going into the S-VHS Jack, and

VCR PB is the VCR playback signal. [VIDEO-IN/S-VIDEO / VCR PB]

■ RECORD TIME MARK

If set to ON, the recording time will be displayed during playback; if set to OFF, it will not

be displayed. [ON/OFF]

■ AUDIO RECORD

Set to ON to record video and audio at the same time, or set to OFF to record video only.

Audio is input and recorded at 6.3 Kbps regardless of the recording field rate of the video

[ON/OFF].

■ TIME MARK POSITION

Set the location on the screen where the time of recording will be displayed during

playback. Set to LEFT to display it on the bottom left of the screen, or set to RIGHT to

display it on the bottom right of the screen. [LEFT/RIGHT]

■ PICTURE QUALITY

Picture quality is divided into four levels. Set to VERY HIGH for the best picture quality,

or set to HIGH, NORMAL, or LOW in the descending order of qualty. The user can select

the desired quality. [VERY HIGH/HIGH/NORMAL/LOW]

Note

Set DVR input to VCR PB mode to show video in live video on screen. You can record

the videotape into hard disk drive while playing it. Note that OSD will not display while

recording. This is normal.

■ PICTURE RATE

Please note that you cannot open VCR menu while setting the DVR input to VCR PB

mode. Timer record setting in DVR menu is disabled as well.

Set the picture rate for the input video. Up to 60 FPS (Fields Per Second) can be recorded.

(SCR-3000P models can record up to 50 FPS (Fields Per Second)

■ SCR-3000N/SSC-Dual (NTSC)

[60.00FPS/30.00FPS/15.00FPS/10.00FPS/7.50FPS/5.00FPS/2.50FPS/1.00FPS/

0.50FPS]

■ SCR-3000P (PAL)

[50.00FPS/25.00FPS/12.50FPS/8.33FPS/6.25FPS/5.00FPS/2.50FPS/1.00FPS/

0.50FPS]

4-7

4-8

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Alarm Record Setup

The following illustrates the intial setting of the ALARM RECORD SETUP menu.

Note

The following table shows how long it would take to fill up an 80GB HDD for each field

rate.

(Recording time for each field rate may slightly vary depending on the type of input

video singal.)

ALARM RECORD SETUP

ALARM SIGNAL DETECTION

ALARM SIGNAL POLARITY

ALARM BUZZER

OFF

N.O.

10 SECOND

2 SECOND

OFF

30.0 FPS

OFF

MAIN ALARM TIME

PRE ALARM TIME LIMIT

POST ALARM TIME LIMIT

MAIN ALARM PICTURE RATE

MOTION DETECTION

Time-Lapse Mode

SET AREA & SENSITIVITY

VERY HIGH

80GB

HIGH

80GB

NORMAL

80GB

LOW

Picture Rate

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

80GB

60.0 FPS

11 H

22 H

13 H

26 H

19 H

37 H

25 H

49 H

■ ALARM SIGNAL DETECTION

30.0 FPS

15.0 FPS

10.0 FPS

7.5 FPS

5.0 FPS

2.5 FPS

1.0 FPS

0.5 FPS

50.0 FPS

25.0 FPS

12.5 FPS

8.3 FPS

6.3 FPS

5.0 FPS

2.5 FPS

1.0 FPS

0.5 FPS

You shall select ON to start recording in the event of alarming and select OFF to prevent

recording in the event of alarming. If you set the ALARM SIGNAL DETECTION to ON

and exit the menu, the system will begin recording whenever alarm occurs. To force stop the

recording during the alarm recording, press and hold the STOP(ꢀ) button for 3 seconds. Then,

the recording by the current alarm will be stoppted, and the alarm recording will not be per-

formed for the next 5 seconds even if alarm occurs. To completely stop the alarm recording,

go into the menu within that 5 seconds to set the ALARM SIGNAL DETECTION to OFF.

If no action is performed by the user for 5 seconds, the system returns to the alarm recording

mode. [ON/OFF]

44 H

53 H

74 H

99 H

65 H

79 H

111 H

148 H

222 H

444 H

1,111 H

2,222 H

27 H

148 H

198 H

296 H

593 H

1,481 H

2,963 H

36 H

NTSC

87 H

106 H

159 H

317 H

794 H

1,587H

19 H

131 H

261 H

654 H

1,307 H

13 H

26 H

38 H

53 H

71 H

■ ALARM SIGNAL POLARITY

52 H

76 H

107 H

160 H

213 H

267 H

533 H

1,333 H

2,667 H

142 H

213 H

284 H

356 H

711 H

1,778 H

3,556 H

78 H

114 H

152 H

190 H

381 H

952 H

1,905 H

Set to N. C. (Normally Close) when the alarm input is Active High, and set to N.O.(Normally

Open) when the alarm input is Active Low. [N.C./N.O.]

PAL

105 H

131 H

261 H

654 H

1,307 H

■ ALARM BUZZER

Set to ON to have the system activate the Buzzer when a motion is deteced in the input

video or when alarm occurs, or set to OFF to keep the Buzzer inactive. [ON/OFF]

■ MAIN ALARM TIME

Set the duration for which alarm recording is to be performed when a motion is detected in the

input video or when alarm occurs. The value can be set from 0 seconds to 5 minutes when you

set to OFF. If you set to AUTO, the alarm recording is performed only during when the alarm

signal is Active.

[5MINUTE/4MINUTE/3MINUTE/2MINUTE/1MINUTE/30SECOND/20SECOND/

10SECOND/AUTO/OFF]

4-9

4-10

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

■ PRE ALARM TIME LIMIT

■ MOTION DETECTION

The pre-alarm recording is an important function which enables you to find out about the situation

immediately before a motion is detected in the input video or before alarm occurs. Set how much

video data you want to record before the motion is detected or alarm is triggered. About 2 seconds

to 10 seconds of video data are stored in the system’s SDRAM at all times. When a motion is detect-

ed or alarm is triggered, as much data as it is set in the PRE ALARM TIME LIMIT is taken from

the SDRAM and written to the HDD as it simultaneously begins the alarm recording. However, since

the capacity of the SDRAM is limited, the field rate of the pre-alarm recording will decrease as the

time set in the PRE ALARM TIME LIMIT is increased.

The DVR will start recording images whenever it detects any movement only when ALARM

SIGNAL DETECTION is set to ON. At this time, you can set the detailed items about the

motion detection in the SET AREA & SENSITIVITY menu.

Even if MOTION DETECTION is set to ON, if you set MULTIPLEXER to WITH in SYS-

TEM SETUP, MOTION DETECTION will be enabled but MOTION RECORD will not be

performed. To force stop the recording started by the motion detection, press and hold the

STOP(ꢀ) button for 3 seconds. Then, the recording started by the motion detection will be

paused for 5 seconds, during which time you should go into the menu and set the MOTION

DETECTION to OFF to completely stop the recording. If no action is performed by the user

for 5 seconds, the system resumes the recording started by motion detection. [ON/OFF]

[10SECOND/8SECOND/6SECOND/4SECOND/2SECOND/OFF]

Caution

If the system is currently recording, the PRE ALARM TIME LIMIT settings will not be

applied even when alarm occurs. The PRE ALARM TIME LIMIT settings are applied

only if the system is not currently recording.

Caution

When performing the recording started by motion detection, the recording time is

determined by the the time set in MAIN ALARM TIME, PRE ALARM TIME LIMIT, and

POST ALARM TIME LIMIT as it was the case in the alarm recording.

■ POST ALARM TIME LIMIT

Set the amount of video data you want to record immediately after a motion is detected in

the input video or alarm is triggered. The system records as long as the time set in the

MAIN ALARM TIME, and then records more data as long as the time set in the POST

ALARM TIME LIMIT.

■ SET AREA & SENSITIVITY

1) AREA

[5MINUTE/4MINUTE/3MINUTE/2MINUTE/1MINUTE/30SECOND/20SECOND/

10SECOND/OFF]

Areas for motion detection are 4 in total and you can set the LEVEL, SIZE, and MOVE

for each area. When you go into SET AREA & SENSITIVITY menu, the following

screen appears and the cursor is positioned at the AREA item. At this time, press the

UP(^ꢀ) or DOWN(❷) button to select the desired area (AREA 0 ~ AREA 3), and press

Note

the ENTER(

) button to move the cursor to the LEVEL item to set the sensitivity

The following illustrates the temporal relationship among the main alarm recording

time (MAIN ALARM TIME), pre-alarm recording time (PRE ALARM TIME LIMIT), and

post alarm recording time (POST ALARM TIME LIMIT) based on the time of alarm

occurrence.

level for the selected area. [0/1/2/3]

AREA=0 LEVEL=OFF [SIZE][MOVE]

Alarm Occurrence

AREA 0

AREA 1

PRE ALARM TIME LIMIT

MAIN ALARM TIME

POST ALARM TIME LIMIT

AREA 2

AREA 3

■ MAIN ALARM PICTURE RATE

Set the main alarm recording field rate.

(SCR-3000P models supports recording from 0.50 FPS (Fields Per Second) up to 50 FPS)

2) LEVEL

■ SCR-3000N/SSC-Dual (NTSC)

Sensitivity to motion can be set from LOW to HIGH+, or to OFF. Closer to HIGH, more

resensitive to motion, closer to LOW, more insensitive to motion.

Press the UP(^ꢀ) or DOWN(❷) buttion to set the sensitivity level, and press the ENTER

[60.00FPS/30.00FPS/15.00FPS/10.00FPS/7.50FPS/5.00FPS/2.50FPS/1.00FPS/

0.50FPS]

■

SCR-3000P (PAL)

(

) button to move the cursor to the SIZE item to set the size of the motion

detection area.

[50.00FPS/25.00FPS/12.50FPS/8.33FPS/6.25FPS/5.00FPS/2.50FPS/1.00FPS/

0.50FPS]

[OFF/LOW/LOW+/MIDDLE/MIDDLE+/HIGH/HIGH+]

4-11

4-12

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Reservation Timer Setup

AREA=2 LEVEL=OFF [SIZE][MOVE]

The following illustrates the intial setting of the TIMER RECORD SETUP menu.

TIMER RECORD SETUP

TIMER

DAY

START

END

FIELD RATE

AREA 2

OFF

--- --:-- --:--

--.--

3) SIZE

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

Set the size of the area currently selected. Press the UP(^ꢀ) button to increase the size

of the area vertically, or press the DOWN(❷) button to decrease the size of the area ver

tically.

■

Timer recording enables the system to automatically record when you are not present so that

the recording is performed on the desired day at the desired time with the desired field rate.

First position the cursor at the line where TIMER row is set to OFF to set it to ON, select

the desired day from the DAY row, and enter the recording start and end time into START

and END row respectively. Also, set the field rate to be applied during recording in the

FIELD RATE row. If you set the DAY from SUN to SAT, the timer recording setting is

applied only to the corresponding days, but if you set it to DAILY, the timer recording

setting is applied to all days of the week. FIELD RATE can also be set from 0.50 FPS up to

60 FPS (0.50 FPS to 50 FPS for the SCR-3000P model). Once the timer recording is set, the

recording will be made on the corresponding day for the duration of entered time. Other

recording settings, except the field rate, follow the basic recording settings.

If an alarm or motion is detected during a timer recording, ALARM RECORD will be per-

formed.

Press the RIGHT(❿) button to increase the size of the area horizontally, or press the

LEFT(➛) button to decrease the size of the area horizontally. After setting the size, press

the ENTER(

) button to move the curstor so that you can set the MOVE item.

AREA=2 LEVEL=MIDDLE [SIZE][MOVE]

If ALARM RECORD ends within the timer recording time, the timer recording will per-

formed again. If the END time of the timer recording time is equal to or less than the

START time, the recording will stop at the END time of the day after the START date. For

example, if DAY is set to MON, START is set to 12:00, and END is set to 11:00, the record-

ing will start at 12 on Monday and end at 11 on Tuesday.

4) MOVE

Set the position of the area currently selected. Press the UP(^ꢀ) or DOWN(❷) button to

change the position of the area vertically, or press the LEFT(➛ ) or RIGHT(❿) button

to change the position of the area horizontally. After setting them all up, press the ENTER

(

) button to move the cursor to the AREA item so that you can set each item for other

When you turn on the system or if you have replaced the HDD, the timer recording will be

performed again if the current time falls within the scheduled time.

areas.

To force stop the recording, press and hold the STOP(ꢀ) button for 3 seconds. Then, the

recording will pause for 5 seconds. If no action is performed by the user for 5

seconds, the system determines whether the timer recording setup time is elapsed and

resumes the recording it not. To completely stop the recording, go into the menu within 5

seconds to set the TIMER item of the corresponding line to OFF.

AREA=2 LEVEL=MIDDLE [SIZE][MOVE]

Timer recording can be set for up to 11 different times.

4-13

4-14

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

System Setup

The following illustrates the intial setting of the SYSTEM SETUP menu.

■ LANGUAGE

SCR-3000N/SSC-Dual models only supports English. SCR-3000P models however supports

German, French, Spanish, and Italian in addition to English.

There is a language support setting function for the convenience of international users. The

default language is set to English.

SYSTEM SETUP

PASSWORD

PASSWORD LOCK

HDD ERASE

****

OFF

FACTORY RESET

MENU SCREEN

LANGUAGE

IR REMOCON

MULTIPLEXER

OFF

DARK GRAY

ENGLISH

OFF

■■SCR-3000N/SSC-Dual [ENGLISH]

■ SCR-3000P [ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO]

WITHOUT

MULTIPLEXER SELECT SAMSUNG SDM-160

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

■ IR REMOCON

■ PASSWORD

If IR REMOCON to ON, signals from the remote control will be received and if it is set to

OFF, signals from the remote control will not be received. The option will be turned off by

factory default reset. For instructions on how to use the remote control, please refer to “4.

Introduction to the Remote Control” on page 1-7. [ON/OFF]

Set the system password. You can enter a 4-digit number and the initial set value is 0000.

■ PASSWORD LOCK

If you set this to ON, the system will ask for a password, which was set in PASSWORD,

when your press the MENU (

) button or when you attempt to cancel the recording lock

■ MULTIPLEXER

If MULTIPLEXER is set to WITHOUT, ID Detection will not be performed and the system

will recognize it as 1CH regardless. If MULTIPLEXER is set to WITH, the Video ID input

from the Multiplexer will be detected. Set MULTIPLEXER to WITH, and exit the MAIN

MENU (DVR) to automatically start the Multiplexer ID Detection. In addition, MULTI-

PLEXER SELECT will be enabled and MOTION DETECTION-related functions will be

disabled.

while recording or when you attempt to remove the video tape from the video deck. If the

password is invalid, you will not be able to finish the desired operation. If you set this to

OFF, the system will not ask for a password for any of the operations above.[ON/OFF]

■ HDD ERASE

If you set to ON and exit the menu, the system will delete all data stored on the HDD.

[WITHOUT/WITH]

[ON/OFF]

■ MULTIPLEXER SELECT

Caution

If MULTIPLEXER is set to WITH, MULTIPLEXER SELECT will be enabled.

The settings of all recording modes will be dependent on the Multiplexer setting.

The corresponding Multiplexers are SAMSUNG SDM-160(SDM-090), SMO-150(SMO-

210, SOM-080).

Verify once again that is is OK to delete the data, as deleted data cannot be restored.

■ FACTORY RESET

■■SCR-3000N/SSC-Dual [SAMSUNG SDM-160 / SAMSUNG SMO-150]

If you set to ON and finish the menu, all settings will be restored to their factory default set-

tings. However, the data on the HDD will not be deleted. After RESET The message, “DO

YOU REBOOT SYSTEM?” will be displayed. Select YES to reboot the system. [ON/OFF]

■ SCR-3000P [SDM-160P / SAMSUNG VPP]

■ MENU SCREEN

Caution

If this is set to DARK GRAY, the background of the screen becomes darker when the

MENU button is pressed and you will not be able to see the characters clearly. If set to OFF,

you can see the current video clearly even when the MENU button is pressed.

[DARK GRAY/OFF]

Do not set the multiplexer option to [With] and fail to receive the multiplexer output

signal as input to avoid error in recording. Please set the multiplexer option to

[Without] whenile not receiving the multiplexer output signal as input.

Set the multiplexer option to [Without] unlessif the multiplexer manufacturer of the

multiplexer is not Samsung.

4-15

4-16

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Communication Setup

The following illustrates the intial setting of the COMMUNICATION SETUP menu.

COMMUNICATION SETUP

BAUD RATE

NETWORK ACCESS

IP ADDRESS

115,200

0. 0. 0. 0

****

GATEWAY

SUBNET MASK

NETWORK USER ID

NETWORK USER PWD

PAN/TILT TYPE

****

SCC-421

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

V. Viewing the

VCR Menu

■ BAUD RATE

Sets data transmission rate in RS-232C communication.

[4,800/9,600/19,200/38,400/115,200]

■ NETWORK ACCESS/IP ADDRESS/GATEWAY/SUBNET MASK

If the system is connected to a LAN, it can be controlled from the remote surveillance pro-

gram installed on a remote PC. To connect to a LAN, set the NETWORK ACCESS to ON,

and configure the IP ADDRESS, GATEWAY, SUBNET MASK, etc. to suit the user’s net-

work environment. Then, connect the LAN Cable to the LAN Cable connection terminal on

the back of the system and reboot the system. If at least one from the IP ADDRESS,

GATEWAY, and SUBNET MASK is modified, the system must be rebooted to apply the

modified setting to the system.

■ NETWORK USER ID/NETWORK USER PWD

In order to access the system through a LAN from a remote surveillance program installed

on a remote PC, the user ID and password must be entered. At this time, the user ID and

password entered match the ones set in the NETWORK USER ID and NETWORK USER

PWD, you can connect to the system; otherwise, you cannot gain access. Both are 4-digit

numbers and the initial set values are 0000.

■ PAN/TILT TYPE (Remote Control of Camera)

You can control the Pan/Tilt/Zoom function of a camera with the remote monitoring

program installed in the remote PC through LAN. Then, you shall select the camera to be

controlled. But, this remote control shall be applied only to SEC SCC-641/SCC-643(N/P)

Cameras and SCC-421(N/P) Series Camera(C4201, C4203, C4301 and C4303) Camera

which use the SAMSUNG Protocol. You can select the camera to be controlled by the

remote monitoring program. Please refer to Remote Monitoring Program Use’s Manual for

the detailed explanation of the remote monitoring program. [SCC-641/SCC-421]

Caution

After setting IP ADDRESS, GATEWAY and SUBNET MASK, exit the MENU. Then, a

message "DO YOU REBOOT SYSTEM?" will appear. If you want to use the changed

NETWORK information, select “YES” to reboot the system.

4-17

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

VCR Menus

Menu Items

Entering the VCR MAIN MENU

VCR

Press the VCR (

) button once. Then the VCR LED will light up. Now press the MENU

■ MANUAL ARCHIVE

■ TIMER ARCHIVE

(

) button. Then the following screen should appear.

MANUAL ARCHIVE

TIMER ARCHIVE

ARCHIVE MENU(VCR)

FROM RECORD EVENT LIST

FROM ALARM EVENT LIST

FROM MOTION EVENT LIST

TIME RANGE

DIRECT ARCHIVE

PICTURE SAMPLING RATE 1/1

TIMER ARCHIVE

SELECT EVENT

OFF

RECORD[X]

ALARM [X]

MOTION[X]

SUN

MANUAL ARCHIVE

TIMER ARCHIVE

ARCHIVE SETUP

ARCHIVE CHECK

DAY

FROM

SAMPLING RATE

12:00:00

1/1

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

MOVE=[ꢀ

/❷] SELECT=[

] EXIT=[MENU]

Note

■ ARCHIVE SETUP

■ ARCHIVE CHECK

- Make sure that the VCR LED is lit before pressing the MENU button. If the VCR

button had not been pressed, the DVR MAIN MENU will be displayed.

ARCHIVE SETUP

ꢁ

TAPE REC IF HDD TROUBLE

ENG [O]

FULL[X]

- Record or Play mode, you cannot go into the menu. To go into the menu, first stop

recording or playback.

VCR SPEED

TAPE SELECT

VCR BUZZER

CHANNEL

T-120

OFF

ARCHIVE CHECK

SELECT

CH 1:ON CH 5:ON CH 9:ON CH13:ON

CH 2:ON CH 6:ON CH10:ON CH14:ON

CH 3:ON CH 7:ON CH11:ON CH15:ON

CH 4:ON CH 8:ON CH12:ON CH16:ON

Methods of selecting a menu item, changing settings, returning to the upper menu, and exiting the

current menu are the same as in the DVR menus.

MOVE=[ꢀ/❷

]

SELECT=[

]

EXIT=[MENU]

Caution

By default, the settings of each menu are as shown above.

5-1

5-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

MANUAL ARCHIVE

➛

❿

The following illustration shows the initial settings of the MANUAL ARCHIVE menu.

Use the LEFT( ), RIGHT( ), UP(

A highlighted cursor should appear over the selected item. Press the ENTER button (

the choice. The selected event will be indicated by "[O]". Repeat this procedure for each event you

ꢀ

) and DOWN(

❷

)

buttons to select the event you want to back up.

) to accept

REC

want to back up, and then press the RECORD (

occurrence will be backed up first.

) button to start the backup. The earliest event

MANUAL ARCHIVE

FROM RECORD EVENT LIST

FROM ALARM EVENT LIST

FROM MOTION EVENT LIST

TIME RANGE

DIRECT ARCHIVE

PICTURE SAMPLING RATE 1/1

Once the backup starts, the following information will be displayed.

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

Event Index

MACHINE

RECORD START

CH No.

: SCR-3000 MACHINE 1

: 2003-06-14 09:45:28

: 1

REC MODE

: 60.00 FPS

ARCHIVING START : 2003-06-14 09:55:35

ARCHIVING METHOD : MANUAL

(1) FROM RECORD EVENT LIST

ARCHIVE

If you have pressed the RECORD button on the main unit to record on the hard drive or if

you have recorded for a long time, the event list will be updated at a certain interval of time.

FROM RECORD EVENT LIST allows you to use this list to perform the backup, more

conveniently than using TIME RANGE. The following illustration shows the FROM

RECORD EVENT LIST screen in detail. The EVENT (RECORD), DATE and TIME

indicate when the event was recorded on the hard drive. To exit this screen and return to the

MANUAL ARCHIVE menu, press the MENU button.

2003-06-14 09:45:45

- MACHINE : "SCR-3000/SSC-Dual MACHINE 1" is the ID for the RS-485 connection.

- RECORD START : The date and time when the data you want to back up was recorded.

- CH No. : The input channel number of the data that you want to back up.

- REC MODE : The picture sampling rate of the recorded data that you want to back up

- ARCHIVING START : Backup start time.

- ARCHIVING METHOD : MANUAL ARCHIVE Method [MANUAL/TIMER/DIRECT]

RECORD EVENT ARCHIVE

ID EVENT DATE

[1/7]

TIME

01 RECORD 2003-07-13 09:23:55 [X]

02 RECORD 2003-07-12 13:43:21 [X]

03 RECORD 2003-07-12 11:13:42 [X]

04 RECORD 2003-07-11 09:23:55 [X]

05 RECORD 2003-07-11 05:11:42 [X]

06 RECORD 2003-07-10 23:51:12 [X]

07 RECORD 2003-07-10 13:37:48 [X]

Note

➛

❿

MOVE=[ꢀ/❷/ / ] START=[REC] EXIT=[MENU]

In REC Mode - that is, if the picture rate of the data to be backed up is less than

15FPS(for NTSC) or 12.5FPS(for PAL) - no audio will be backed up.

5-3

5-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

(2) FROM ALARM EVENT LIST

(3) FROM MOTION EVENT LIST

FROM ALARM EVENT LIST allows you to back up the video and audio data that has been

recorded on the hard drive at the time of an event, which is triggered by alarm input or

motion detection, onto a video tape. The following illustration shows the FROM ALARM

EVENT LIST screen in detail. The EVENT (ALARM), DATE and TIME indicate when the

event was recorded on the hard drive. To exit this screen and return to the MANUAL

ARCHIVE menu, press the MENU button.

FROM MOTION EVENT LIST allows you to back up the video and audio data that has been

recorded on the hard drive at the time of an event, which is triggered by motion detection,

onto a video tape. The following illustration shows the FROM MOTION EVENT LIST

screen in detail. The EVENT (MOTION), DATE and TIME indicate when the event was

recorded on the hard drive. To exit this screen and return to the MANUALARCHIVE menu,

press the MENU button.

ALARM EVENT ARCHIVE

ID EVENT DATE

01 ALARM 2003-07-13 17:25:52 [X]

02 ALARM 2003-07-12 06:37:38 [X]

03 ALARM 2003-07-11 11:54:34 [X]

[01/03]

TIME

MOTION EVENT ARCHIVE

ID EVENT DATE

01 MOTION 2003-07-13 22:42:16 [X]

02 MOTION 2003-07-12 14:24:45 [X]

03 MOTION 2003-07-11 06:13:52 [X]

[01/03]

TIME

➛

❿

➛

❿

MOVE=[ꢀ

❷/ / ] START=[REC] EXIT=[MENU]

MOVE=[ꢀ

❷/ / ] START=[

] EXIT=[MENU]

Use the UP (ꢀ) and DOWN (❷) buttons to select the event you want to back up. A highlight-

ed cursor should appear over the selected item. Press the ENTER ( ) button to accept the

choice to set the event to [O]. Repeat this procedure for each event you want to back up, and

Use the UP (ꢀ) and DOWN (❷) buttons to select the event you want to back up. A highlight-

ed cursor should appear over the selected item. Press the ENTER ( ) button to accept the

choice to set the event to [O]. Repeat this procedure for each event you want to back up, and

REC

then press the RECORD (

be backed up first.

) button to start the backup. The earliest event occurrence will

REC

then press the RECORD (

be backed up first.

) button to start the backup. The earliest event occurrence will

Once the backup starts, the following information will be displayed.

Event Index

MACHINE

RECORD START

CH No.

: SCR-3000 MACHINE 1

: 2003-06-14 09:45:28

: 1

REC MODE

: 60.00 FPS

ARCHIVING START : 2003-06-14 09:55:35

ARCHIVING METHOD : MANUAL

Event Index

MACHINE

RECORD START

CH No.

: SCR-3000 MACHINE 1

: 2003-06-14 09:45:28

: 1

ARCHIVE

2003-06-14 09:45:45

REC MODE

: 60.00 FPS

ARCHIVING START : 2003-06-14 09:55:35

ARCHIVING METHOD : MANUAL

ARCHIVE

Note

2003-06-14 09:45:45

- If MULTIPLEXER in the SYSTEM SETUP menu of the DVR MAIN MENU is set to

WITH, MOTION EVENT ARCHIVE will be disabled. To perform the backup, set

MULTIPLEXER in the SYSTEM SETUP menu to WITHOUT.

5-5

5-6

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

(4) TIME RANGE

(5) DIRECT ARCHIVE

From the MANUAL ARCHIVE menu, select "TIME RANGE" and the following screen

appears. In the TIME RANGE ARCHIVE screen, you can set the start and end times of a

particular section of the video and audio that you want to back up from the hard drive.

DIRECT ARCHIVE allows you to back up the desired scenes to a video tape regardless of

VCR

EVENT RECORD. First locate the desired scene. Next, press the VCR (

VCR mode. Enter the MANUAL ARCHIVE menu, select DIRECT ARCHIVE, and then

press the ENTER ( ) button. The scene you have chosen will be backed up to the video

) button to enter

tape. If you perform DIRECT ARCHIVE without locating the scene you want to back up, the

backup will start from the last position stopped at during playback.

TIME RANGE ARCHIVE

SELECT EVENT

RECORD [X]

ALARM [X]

MOTION [X]

2003-07-10 13:37:48

2003-07-13 22:43:54

FROM

Event Index

MACHINE

RECORD START

CH No.

: SCR-3000 MACHINE 1

: 2003-06-14 09:45:28

: 1

➛

❿

MOVE=[ꢀ/❷/ / ] SELECT=[REC] EXIT=[MENU]

REC MODE

: 60.00 FPS

ARCHIVING START : 2003-06-14 09:55:35

ARCHIVING METHOD : DIRECT

First select the event type. Next, set the start and end times of the section you want to back up.

For example, if you want to back up the RECORD and MOTION types of events, set these

ARCHIVE

2003-06-14 09:45:45

two types of events to [O]. Next, enter the backup start and end times, and then press the

REC

RECORD (

) button. The RECORD and MOTION events within the specified time inter-

Note

val will be backed up earliest to most recent. Even if ALARM events are found within the sec-

tion you have specified, they will be ignored because you did not select that event type.

- Even if you locate the desired scene and play it back in DVR mode for DIRECT

ARCHIVE, playback will stop as soon as you press the VCR button.

Event Index

MACHINE

RECORD START

CH No.

: SCR-3000 MACHINE 1

: 2003-06-14 09:45:28

: 1

(6) PICTURE SAMPLING RATE

REC MODE

: 60.00 FPS

ARCHIVING START : 2003-06-14 09:55:35

ARCHIVING METHOD : MANUAL

PICTURE SAMPLING RATE allows you to reduce the picture sampling rate by a fraction-

al number when backing up the hard drive to a video tape. For example, if you set the rate

to 1/2 and back up the data that has been recorded at 30 fps, it will be backed up to the video

tape at 15 fps.

ARCHIVE

2003-06-14 09:45:45

Note

- If you back up the data after setting the picture sampling rate to a rate between

1/2 and 1/16, no audio will be backed up. Please note that this is not a malfunc-

tion.

- If MULTIPLEXER in the SYSTEM SETUP menu of the DVR MAIN MENU is set to

WITH, the MOTION event type will be disabled for SELECT EVENT in the TIME

RANGE menu. To perform the backup, set MULTIPLEXER in the SYSTEM SETUP

menu to WITHOUT.

5-7

5-8

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

TIMER ARCHIVE

The following illustration shows the initial settings of the TIMER ARCHIVE menu.

TIMER ARCHIVEE

End Time

TIMER ARCHIVE

Start Time

RECORD EVENT

TIMER ARCHIVE

SELECT EVENT

OFF

RECORD[X]

ALARM [X]

MOTION[X]

SUN

DAY

FROM

SAMPLING RATE

12:00:00

1/1

Current Time

Date being archived

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[MENU]

The TIMER ARCHIVE time is a future time, rather than the current time. If the time you set

is earlier than the current time, it is tomorrow's time or a time in the next week. In the above

illustration, the TIMER ARCHIVE time is set and there are 3 record events. The first event

overlaps with the TIMER ARCHIVE start time. In this case, archiving will start at the start

time of the record event that is overlapping. Archiving will start as an event ends. The third

event is overlapping with the end time of TIMER ARCHIVE. In this case, only the data

between the event start time and archiving end time will be archived when the TIMER

ARCHIVE set time ends, even if the record event is not finished.

The Timer Backup function allows you to set the system to automatically back up the data

that is recorded on the HDD to a video tape while you are away from the system. You can

set the system to back up the desired type of event on the desired day of the week and time

at the desired sampling rate. First set TIMER ARCHIVE to ON. Next, select all event types

you want to back up by setting them to [O]. For example, a backup will not be performed,

even if an alarm event occurs during the set time, unless ALARM EVENT is set to [O]. Set

ARCHIVE SCHEDULE by selecting one from the following: SUN, MON, TUE, WED,

THU, FRI, SAT, MON-FRI, MON-SAT, and DAILY. Enter the backup start and end times

into FROM and TO fields respectively. Finally, set the picture sampling rate to the desired

value between 1/1 to 1/16.

To cancel the TIMER ARCHIVE you have set, press the STOP(ꢀ) button for 3 seconds. The

TIMER ARCHIVE will pause for 5 seconds. However, if you do not make any action for 5

seconds, the system will reset to the Timer Archive after 5 seconds have elapsed. To com-

pletely cancel the TIMER ARCHIVE, enter the menu within 5 seconds and set the

TIMER ARCHIVE to OFF.

Note

- If MULTIPLEXER in the SYSTEM SETUP menu of the DVR MAIN MENU is set to

WITH, the MOTION event type will be disabled for SELECT EVENT of the TIMER

ARCHIVE menu.

Because TIMER ARCHIVE is an automatic backup for the data that will be recorded, any

data that has already been recorded will not be backed up. The following illustrates the

timeline of TIMER ARCHIVE.

5-9

5-10

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

ARCHIVE SETUP

The following illustration shows the initial settings of the ARCHIVE SETUP menu.

(3) TAPE SELECT

Set the tape length for accurate calculation of remaining tape time and precise control.

■ SCR-3000N/SSC-Dual [T-120/T-160/T180]

ARCHIVE SETUP

TAPE REC IF HDD TROUBLE EMG [O]

FULL[X]

■ SCR-3000P [E-180/E-210/E-260]

VCR SPEED

TAPE SELECT

VCR BUZZER

CHANNEL

T-120

OFF

SELECT

(4) VCR BUZZER

CH 1:ON CH 5:ON CH 9:ON CH13:ON

CH 2:ON CH 6:ON CH10:ON CH14:ON

CH 3:ON CH 7:ON CH11:ON CH15:ON

CH 4:ON CH 8:ON CH12:ON CH16:ON

Set the buzzer so that the VCR's status could be known. If there is a problem in VCR SYS-

TEM Set it to ON to enable the BUZZER and to OFF to disable the BUZZER.

MOVE=[ꢀ/❷

]

SELECT=[

]

EXIT=[MENU]

The buzzer will sound in the following cases.:

- If there is a problem in the VCR SYSTEM.

(1) TAPE REC IF HDD TROUBLE

- If the tape reaches the end part or is in PRE END (when the remaining time is less than 5

minutes) during ARCHIVE.

- If there is no tape inserted, or REC Safety TAB is removed from the inserted tape when

you start ARCHIVE, or in TIMER ARCHIVE MODE. [ON/OFF]

1) EMG

Set whether to allow the VCR to continue the recording if the hard drive fails for some rea-

son. If there is a problem in HDD, it will automatically execute VCR BACKUP. If you

replace the failed hard drive with a new one, VCR backup will be cancelled and the system

will to the previous state, before the failure occurred. [O/X]

(5) CHANNEL

CHANNEL is enabled if MULTIPLEXER is set to WITH and disabled if it is set to WITH-

OUT. If CHANNEL is enabled and you set it to SELECT, all channels recorded on the hard

drive will be displayed. If you set it to ALL, all channels will be set to ON and become tar-

gets for backup. [SELECT/ALL]

2) FULL

Set whether to allow the VCR to continue the recording if DISK END MODE is set to

STOP. However, if DISK END MODE is set to OVERWRITE, this will be disabled.

[O/X]

(2) VCR SPEED

Set the recording mode for the VCR. If you set this to SP, recording time will be shorter

but picture quality will be better than setting it to SLP; and if you set this to SLP, record-

ing time will be longer but picture quality will be poorer than setting it to SP.

■ SCR-3000N/SSC-Dual [SP/SLP]

■ SCR-3000P [SP/LP]

Note

- Recording Time to Recording Mode

SLP

SCR-3000N/SSC-Dual (NTSC, based on T-120)

SCR-3000P (PAL, based on E-180)

2 Hours

6 Hours

3 Hours

6 Hours

5-11

5-12

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

ARCHIVE CHECK

The ARCHIVE CHECK function allows you to check whether the images played back on

the DVR and transferred to the VCR are recorded correctly. The DVR plays back the signals

to be Archived for 5 seconds and send them to the VCR and the VCR records them.

After 5 seconds, the DVR stops playback and the VCR stops recording at the same time. The

VCR plays back 5 seconds of the most recently recorded data. ARCHIVE CHECK cannot

be performed during archiving; it is possible after archiving has stopped.

To perform ARCHIVE CHECK, in VCR mode, place the cursor at the ARCHIVE CHECK

of ARCHIVE MENU and press the ENTER (

) button or press the ARC CHECK but-

ton on the remote control. The ARCHIVE CHECK will start and the following screen will

appear.

■

ARCHIVE CHECK

In the above screen, signals from the DVR are being recorded on the VCR for about 5 sec-

onds. After about 5 seconds, ꢀ icon will appear at the top left corner of the screen and the

❿

VCR will rewind to the start point of the most recently recorded images. Then, icon will

appear and the VCR will play back the backed-up data.

Note

- The VCR play screen will not be output to S-VIDEO OUT.

5-13

Download from Www.Somanuals.com. All Manuals Search And Download.

VI. Record

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Basic Record

■ RECORD STOP

Press the STOP(ꢀ) button to stop recording. Then, the light will go off in the RECORD

■ CURRENT IMAGE RECORD

REC

(

) button and recording will stop with the following message on the bottom of the

Press the RECORD(

) button to record current image. If doing so, the light of the

REC

screen.

RECORD(

) button turns on and record starts while following message appears on

the screen. Settings related with record are done in the RECORD MODE SETUP menu.

2003-06-01 12:00:00

RECORD OFF

RECORD ON

Note

- Recording is possible both when the system is in the Live screen mode or in the

playback mode. However, whereas the Live screen currently showing will be

recorded when the system is in the Live screen mode, the video that is currently

being input separate from the screen currently being played will be recorded when

the system is in the playback mode.

Note

Menu screen will not be displayed even if the MENU button is pressed during recording.

If the MENU button is pressed during the recording, the following message will appear.

To view the menu screen, the recording must be stopped.

REC

- While the user is in the menu, pressing the RECORD(

recording. To start the recording, first exit the menu.

) button will not start the

2003-06-01 12:00:00

If the incoming video signal is disconnected during recording, recording will be stopped.

But, if the incoming video signal is reconnected, the system recognizes this and start to

PLEASE STOP RECORD

REC

record again. In addition, when pressing RECORD(

) button without connecting any

video signals to the input port, the following Message is shown on the screen and the system

will not carry out the recording function.

If there is a copy protection signal while receiving VIDEO input image from DVD or

VIDEO TAPE, it records for a moment and stops recording with "COPY PROTECT"

message on the screen.

2003-06-01 12:00:00

NO VIDEO INPUT

6-1

6-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Record Lock

Alarm Record

2 3

Record Lock

Record in Alarm Occurrence

Press the REC LOCK ( ^{REC LOCK}) button during recording to lock the recording. Then, the REC

There is an alarm input terminal (ALARM IN) on the external I/O port at the back panel of

the DVR COMBO system. Connect here the alarm output terminal of an external device,

such as Multiplexer. (For detailed information on connections, please refer to “3. System

Connection for Alarm Recording” on p. 2-3.) Next, set the ALARM SIGNAL DETEC-

TION of the ALARM RECORD SETUP menu to ON to begin recording whenever alarm

is triggered. Also, set the MOTION DETECTION of the ALARM RECORD SETUP

menu to ON to begin the alarm recording whenever a motion is detected within the area set

in the SET AREA & SENSITIVITY.

LOCK ( ^{REC LOCK}) button will light up. At this time, pressing the STOP (ꢀ) button will not stop

the recording. An

mode.

icon appears on the top left of the screen when in the Recording Lock

(Please refer to “Viewing Screen during Recording” on p. 3-6.)

Record Lock Release

REC LOCK

To cancel the Recording Lock, press the REC LOCK (

) button.

When the REC LOCK ( ^{REC LOCK}) button lights up, press the STOP (ꢀ) button to stop recording.

If the PASSWORD LOCK of the SYSTEM SETUP menu is set to ON, you must enter a

password to cancel the recording lock. At this time, if the password entered matches the one

set in the PASSWORD of the SYSTEM SETUP menu, then the recording lock will be can-

celled; otherwise, it will not be cancelled.

Release of Alarm Record

If the system is not in the alarm recording mode, in order to cancel the alarm recording

mode, set the ALARM SIGNAL DETECTION and MOTION DETECTION of the

ALARM RECORD SETUP menu to OFF. To force stop the recording during the record-

ing started by an alarm, press and hold the STOP(ꢀ) button for 3 seconds. Then, the record-

ing by the current alarm will be stoppted, and the alarm recording will not be performed for

the next 5 seconds even if alarm occurs. To completely stop the alarm recording, go into the

menu within those 5 seconds to set the ALARM SIGNAL DETECTION to OFF. If no

action is performed by the user for 5 seconds, the system returns to the alarm recording

mode.

6-3

6-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Reservation Record

Reservation Record Setup

You can enter the day, time, and field rate for the timer recording in the TIMER RECORD

SETUP menu so that the recording will be made on the set day for the set amount of time.

Reservation Record Cancel

If the system is not in the timer recording mode, in order to cancel the timer recording, set

the TIMER row of the line you want to cancel to OFF in one of the timer recording list set

in the TIMER RECORD SETUP menu. However, if you want to force stop the timer

recording during the recording, press and hold the STOP(ꢀ) button for 3 seoncs. Then, the

recording will pause for 5 seconds. If no action is performed by the user for 5 seconds, the

system determines whether the timer recording setup time is elapsed and resumes the record-

ing it not. To completely stop the recording, go into the menu within 5 seconds to set the

TIMER item of the corresponding line to OFF.

VII. Retrieval

and Playback

Caution

REC

To stop the recording when you are recording by pressing the RECORD(

)

button , shortly press the STOP(^ꢀ) button. However, if you want to stop the record-

ing which isthe alarm or motion recording or timer recording, you should press and

hold the STOP(^ꢀ) button for 3 seconds. This is to give the user an opportunity to

change themenu settings to completely stop the recording after pressing and holding

the STOP(^ꢀ) button for 3 seconds to force stop the recording. Because if the system

is in the recording mode by alarm or motion detection, or in the timer recording

mode, there is no special method for the user to arbitrarily stop the recording and

the user cannot go into the menu during the recording, unless an alarm or motion is

not detected or the timer recording setting time is not elapsed.

6-5

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Search Menus

Returning to the Upper Menu or Exit the Current Menu

Entering the DVR SEARCH MENU

Press the SEARCH (

) button to exit the current menu level or to return to the upper menu.

To search the recorded data, press the SEARCH ( ^SEARCH) button. Then the following screen

should appear.

Menu Items

■ DATE & TIME SEARCH

■ RECORD EVENT SEARCH

SEARCH MENU

DATE & TIME SEARCH

RECORD EVENT SEARCH

ALARM EVENT SEARCH

MOTION EVENT SEARCH

PB CHANNEL SETUP

DATE & TIME SEARCH

RECORD EVENT SEARCH

ID EVENT DATE

[1/7]

TIME

DATE&TIME 2003-07-10 13:37:48

[SEARCH START]

01 RECORD START 2003-07-13 09:23:55

02 RECORD START 2003-07-12 13:43:21

03 RECORD START 2003-07-12 11:13:42

04 RECORD START 2003-07-11 09:23:55

05 RECORD START 2003-07-11 05:11:42

06 RECORD START 2003-07-10 23:51:12

07 RECORD START 2003-07-10 13:37:48

SYSTEM INDICATION

MOVE=[ꢀ/❷] SELECT=[

] EXIT=[SEARCH]

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[SEARCH]

MOVE=[ꢀ/❷ꢂ➛ꢂ❿] SELECT=[

] EXIT=[SEARCH]

Note

■ ALARM EVENT SEARCH

■ MOTION EVENT SEARCH

- If the system is in Live Screen mode, Record mode, or Play mode, you can search

all recorded data.

ALARM EVENT SEARCH

ID EVENT

01 ALARM START 2003-07-13 17:25:52

02 ALARM START 2003-07-12 06:37:38

03 ALARM START 2003-07-11 11:54:34

[01/03]

TIME

MOTION EVENT SEARCH

ID EVENT DATE

01 MOTION START 2003-07-13 22:42:16

02 MOTION START 2003-07-12 14:24:45

03 MOTION START 2003-07-11 06:13:52

[01/03]

TIME

DATE

- If you search the recorded data during playback, the newly searched data will be

played regardless of which data was playing previously.

- While you are in a menu, you cannot go into the SEARCH MENU by pressing the

SEARCH ( ^SEARCH) button. To go into the SEARCH MENU, exit the menu you are cur-

rently in.

MOVE=[ꢀ/❷ꢂ➛ꢂ❿] SELECT=[

] EXIT=[SEARCH]

MOVE=[ꢀ/❷ꢂ➛ꢂ❿] SELECT=[

] EXIT=[SEARCH]

■ PB CHANNEL SETUP

■■ SYSTEM INDICATON

Selecting a Menu Item

SYSTEM INDICATION

PB CHANNEL SETUP

Use the UP(ꢀ) or DOWN(❷) buttons to move to the menu item you want.

POWER EVENT LIST

SYSTEM INFORMATION

SYSTEM STATUS

CH 1 : ON CH 5 : ON CH 9 : ON CH13 : ON

CH 2 : ON CH 6 : ON CH10 : ON CH14 : ON

CH 3 : ON CH 7 : ON CH11 : ON CH15 : ON

CH 4 : ON CH 8 : ON CH12 : ON CH16 : ON

A highlighted cursor should appear over the selected item. Next, press the ENTER (

button to accept the choice. In submenus, you can set the criteria for your data search or

select and play back an item from the list of recorded data.

)

➛

❿

MOVE=[ꢀ/❷] SELECT=[

] EXIT=[SEARCH]

MOVE=[^ꢀ

❷/ / ] SELECT=[

] EXIT=[SEARCH]

Setting the Search Criteria & Selecting an Item from the List

Caution

In the DATA & TIME SEARCH menu, set the search criteria. In the RECORD EVENT

SEARCH and ALARM EVENT SEARCH, MOTION EVENT SEARCH menus, select one

from the list of recorded data. Methods of setting the search criteria and selecting an item

from the list are the same as in other menus.

No list will be displayed when you go into the RECORD EVENT SEARCH or

ALARM EVENT SEARCH, MOTION EVENT SEARCH menu, or the POWER EVENT

LIST screen because no data is recorded on the hard drive when it is first shipped

from the factory.

7-1

7-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Retrieval by Date and Time

Recorded Data List View

2 3

DATE & TIME SEARCH

DATE&TIME 2003-07-10 13:37:48

[SEARCH START]

RECORD EVENT SEARCH

ID EVENT DATE

[1/7]

TIME

01 RECORD START 2003-07-13 09:23:55

02 RECORD START 2003-07-12 13:43:21

03 RECORD START 2003-07-12 11:13:42

04 RECORD START 2003-07-11 09:23:55

05 RECORD START 2003-07-11 05:11:42

06 RECORD START 2003-07-10 23:51:12

07 RECORD START 2003-07-10 13:37:48

➛

❿

MOVE=[ꢀ

❷/ / ] SELECT=[

] EXIT=[SEARCH]

➛

❿

MOVE=[ꢀ/❷/ / ] SELECT=[

] EXIT=[SEARCH]

Enter the date and time you want to search, place the cursor at SEARCH START, and then press

the ENTER ( ) button. The following screen will appear and the system will start the data

search. If the data corresponding to the date and time you entered is not available, the list that is

closest to the date and time you entered will be searched.

Of those data recorded on the HDD, the ones recorded by motion detection will be listed in

order of recording start time. The list will be updated every 30 minutes, based on 30 FPS.

Therefore, the system will create a new list during recording after 30 minutes has elapsed from

the previous event.

REC

The system begins the recording when the RECORD(

) button is pressed, or when a motion

is detected or alarm is triggered, or when the timer recording time is up, here the list of the data

recorded by motion detection or alarm occurrenceis not displayed.

Place the cursor at one of the items on the list of the recorded data and press the ENTER (

button. The system will start the data search.

)

Next, the following screen will appear and the data event that you want to search will be played

back.

Once the system has finished searching the data, a pause screen of the searched data will appear.

You can play retrieval data if pressing the PLAY/STILL(❿ ) button. Press the STOP(ꢀ) button to

stop play. Following screen is a screen appearing when pressing the PLAY/STILL(❿ ) button. Date

and time below the screen show when currently played data are recorded and figures at the far end

shows which times of frame of the relevant second.

❿

2003-05-24 01:49:31

❿

2003-09-24 12:30:45

Caution

If you do not correctly set the date and time, it cannot properly search at DATE &

TIME SEARCH, resulting in "SEARCH FAIL". Make sure to use the system after

properly setting the data and time.

7-3

7-4

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Alarm Record Retrieval

Searching Motion Detection Recordings

4 5

MOTION EVENT SEARCH

ID EVENT DATE

[01/03]

TIME

ALARM EVENT SEARCH

ID EVENT

[01/03]

TIME

DATE

01 MOTION START 2003-07-13 22:42:16

02 MOTION START 2003-07-12 14:24:45

03 MOTION START 2003-05-11 06:13:52

01 ALARM START 2003-07-13 17:25:52

02 ALARM START 2003-07-12 06:37:38

03 ALARM START 2003-07-11 11:54:34

➛

❿

MOVE=[^ꢀ/❷/ / ] SELECT=[

] EXIT=[SEARCH]

➛

❿

MOVE=[ꢀ/❷/ / ] SELECT=[

] EXIT=[SEARCH]

Of those data recorded on the HDD, the ones recorded by motion detection will be listed in

order of recording start time. Other information is same as in "3. Viewing the Recorded Data

List" on page 7-4.

Among the data on the HDD, the ones that were recorded when an alarm was triggered will be

displayed as a list based on the recording start time.

Other information is same as in “3. Recorded Data List View” on p. 7-4.

Note

If the list of the recorded data cannot be shown in a screen, you can use the LEFT(➛)

or RIGHT(❿) button to view the list in pages. Press the LEFT(➛) button to move to the

previous page, or press the RIGHT( ❿) button to move to the next page.

- If the list of the recorded data cannot be shown in a screen, you can use the

LEFT(➛) or RIGHT(❿) button to view the list in pages. Press the LEFT(➛) button to

move to the previous page, or press the RIGHT( ❿) button to move to the next page.

- In DVR MENU, if MULTIPLEXER of SYSTEM SETUP is set to WITH, MOTION EVENT

SEARCH of SEARCH MENU will be disabled.

7-5

7-6

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

PB CHANNEL SETUP

SYSTEM INDICATION

6 7

The following screen appears when you select SYSTEM INDICATION.

PB CHANNEL SETUP

CH 1 : ON CH 5 : ON CH 9 : ON CH13 : ON

CH 2 : ON CH 6 : ON CH10 : ON CH14 : ON

CH 3 : ON CH 7 : ON CH11 : ON CH15 : ON

CH 4 : ON CH 8 : ON CH12 : ON CH16 : ON

SYSTEM INDICATION

POWER EVENT LIST

SYSTEM INFORMATION

SYSTEM STATUS

➛

❿

MOVE=[^ꢀ

❷/ / ] SELECT=[

] EXIT=[SEARCH]

When recording in conjunction with a multiplexer, you can show or hide the playback of a par-

ticular channel. Set the channel to ON to show it or set the channel to OFF to hide it.

MOVE=[ꢀ/❷] SELECT=[

] EXIT=[SEARCH]

(1) POWER EVENT LIST

Note

POWER EVENT LIST

ID EVENT

01 POWER ON

02 POWER OFF 2003-09-24 00:07:38

03 POWER ON 2003-09-24 00:11:56

04 POWER OFF 2003-09-24 00:23:24

05 POWER ON 2003-09-24 00:39:12

06 POWER OFF 2003-09-24 01:47:06

07 POWER ON 2003-09-24 02:52:10

08 POWER OFF 2003-09-24 02:55:37

[01/08]

TIME

2003-09-24 00:00:52

If MULTIPLEXER in the SYSTEM SETUP menu of the DVR MAIN MENU is set to

WITHOUT, PB CHANNEL SETUP will be disabled.

DATE

➛

❿

MOVE=[ꢀ/❷/ / ] EXIT=[SEARCH]

The dates and times when the system was turned on and off will be displayed in chronologi-

cal order.

7-7

7-8

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

1) HDD SYSTEM

(2) SYSTEM INFORMATION

This shows the status of the hard drive. Messages used to indicate hard drive status and their mean-

ings are as follows:

The following illustration shows the initial settings of the SYSTEM INFORMATION menu.

- OK : Normal

SYSTEM INFORMATION

- HDD NOT IN : The hard drive rack is empty or the hard drive rack lock is unlocked.

HDD1

CAPACITY(GB)

OVERWRITE(#)

VERSION

80.00

00000

SCR3000 V1.00

00-00-F0-XX-XX-XX

2) HDD REMAIN

MAC ADDRESS

This shows the remaining hard drive space. However, if DISK END MODE in the RECORD

MODE SETUP menu is set to OVERWRITE, "OVERWRITE" will be displayed. The percentage of

remaining space will be displayed only if DISK END MODE is set to STOP.

EXIT=[SEARCH]

3) VCR SYSTEM

It displays the basic system information.

This shows the status of the VCR. If the VCR fails, the CHECK LED will blink and the buzzer will

sound. Messages used to indicate VCR status and their meanings are as follows:

- OK : Normal

If DISK END MODE in the RECORD MODE SETUP menu and the hard drive's capacity

(GB: Gigabyte) are set to OVERWRITE, you can tell from the information shown in the

CAPACITY(GB) and OVERWRITE(#) fields the number of times the hard drive has been

overwritten. The VERSION field shows the version of the software installed on the system

and the MAC ADDRESS field shows the MAC address entered in the system.

- DE : Drum Motor Emergency

- CE : Capstan Motor Emergency

- LE : Loading Motor Emergency

4) TAPE STATUS

(3) SYSTEM STATUS

This shows the status of the video tape. If the current status of TAPE STATUS is not normal, the

CHECK LED blinks and the BUZZER will sound at the interval of 1 second or continuously.

Messages used to indicate tape status and their meanings are as follows:

- OK : Normal

The following illustration shows the initial settings of the SYSTEM STATUS menu.

SYSTEM STATUS

HDD SYSTEM

HDD REMAIN

VCR SYSTEM

TAPE STATUS

TAPE REMAIN

- REC PROTECT: When the it hasinserted tape has theremoved of REC SAFETY TAB removed.

- TAPE NOT IN: When the VIDEO TAPE is not inserted.

OVERWRITE

--:--

- TAPE END: When the VIDEO TAPE reaches the end part.

- TAPE PRE-END: When the remaining time of VIDEO TAPE is less than 5 minutes.

EXIT=[SEARCH]

5) TAPE REMAIN

This shows the amount of physical tape capacity remaining.

7-9

7-10

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Basic Playback

To immediately play back the data recorded on the HDD, press the PLAY/STILL(❿

)

button.

Press PLAY/STILL (❿ ) button during playback. The following screen will appear and the system will

❿

➛

The following screen will appear and the beginning of the recorded data will be played back in

turn.

pause temporarily. Use the RIGHT ( ) or LEFT ( ) button to view a frame at a time in forward or

backward direction.

PLAY

2003-06-01 12:00:00

❿

2003-06-01 12:00:00

To play back again, press the PLAY/STILL(❿ button.

)

Note

- They can all be played back if the system is in the Live screen mode or in the

recording mode.

- While the user is in the menu, pressing the PLAY/STILL(❿ button will not start the

)

playback. To start the playback, first exit the menu.

Note

Menu screen will not be displayed even if the MENU button is pressed during play

back. If the MENU button is pressed during playback, the following message will

appear. To view the menu screen, the playback must be stopped.

To stop playback, press the STOP (ꢀ) button. Press the PLAY/STILL(❿ button again to resume

)

playback from where you last stopped. When the data reaches the end of the HDD during play-

back, the playback will start from the beginning of the HDD.

2003-06-01 12:00:00

PLEASE STOP PLAY OR STILL

- Once you erase the hard disk drive, you will not be able to play newly recorded

video until an event is created. At the initial playing after the erase, video can

pause momentarily.

7-11

7-12

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

VCR Playback

❿❿

Press FF (RIGHT) ( ) button during play to fast-forward the video and easily find a desired

Take following steps to play recorded videotape. Insert the videotape into deck. Turn VCR LED

VCR

➛➛

scene. Hold on the FF (RIGHT) (

) button to forward even faster. Sound will mute while for-

by pressing VCR button (

) once. Then press PLAY/STILL(❿ button.

)

❿❿

warding. Pressing the FF (RIGHT) ( ) button while not playing will only fast-forward without

playing it.

Note

➛➛

To rewind the video, press Rewind (LEFT) (

works.

) button just as the fast-forward function

- You can play video whether the system is in live screen mode or recording mode.

- Pressing the PLAY/STILL(❿ button will not start playing while the menu is

)

Press double speed play button on the remote controller (X2) to fast forward in double speed.

However, screen shaking or noise can occur in the double speed mode. Try to compensate it by

pressing TRACKING (ꢀ/❷) button on the remote controller.

opened. First escape from the menu before playing video.

Press STOP (ꢀ) button to stop play. Press PLAY/STILL(❿ button to pause and resume. Press

)

Automatic noise control will be performed while playing the VCR. If automatic noise control is

SLOW button on lower are of remote controller or press SLOW button on top of the unit for

slow play. Repeating SLOW- button on top of the unit will make the play even slower. Pressing

SLOW+ button will gradually compensate it but still the play will slower than normal speed.

not functioning correctly, press TRACKING (ꢀ/❷) button to control manually.

Press PLAY/STILL(❿ button to return to normal speed play.

)

TRACKING 

TRACKING 

SLOW +

SLOW -

Fast Forward

Rewind

SLOW

7-13

7-14

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Playing Back a Section Repeatedly

Searching the Backed-up Data (VISS)

The VISS function allows you to quickly and easily search the data backed up on to a video

tape.

The REPEAT function allows you to repeatedly play back a certain section during DVR or VCR

playback. The REPEAT function can be operated from the remote control only.

The VISS function can be operated from the remote control only.

(1) DVR A-B Repeat Playback

During DVR playback, press the REPEAT button at the start point of the section you want to

play back repeatedly. At this time, "REPEAT" blinks on the bottom left part.

Press the REPEAT button again at the end point of the section you want to play back repeat-

edly. The specified section will be played back 5 times. "REPEAT" will appear at the bottom

➛➛ ❿❿

will appear on the

In VCR mode, press the VISS button on the remote control,

screen.

left of the screen. To cancel the A-B Repeat, press the PLAY/STILL(❿ button twice. Please

)

➛➛

Press the REW (I

❿❿

) or FF ( I) button depending on the direction of your search. The

note that A-B Repeat Playback will work only if the DVR's playback speed is set to normal,

1/5, or 1/2.

closest data in either direction will be played back for 5 seconds along with the backup infor-

mation. When you have found the data you want, press the PLAY/STILL ( II) button. The

❿

search will stop and the data will be played back. To stop the VISS search, press the STOP

(ꢀ) button.

(2) VCR A-B Repeat Playback

Note

During VCR playback, press the REPEAT button at the start point of the section you want to

➛❿

play back repeatedly. At this time, "

" blinks on the upper left part. .

During a VISS search, the screen will be live.

Press the REPEAT button again at the end point of the section you want to play back repeat-

➛❿

edly. The specified section will be played back 5 times. "

" will appear at the top left of

button twice. Please note

the screen. To cancel the A-B Repeat, press the PLAY/STILL(❿

)

that A-B Repeat Playback will work only if the DVR's playback speed is set to normal.

7-15

7-16

Download from Www.Somanuals.com. All Manuals Search And Download.

VIII. Others

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Product Standards

Appearance Drawing

1 2

Rated Voltage

Power Consumption

HDD

NTSC (AC 110 ~ 240V, 60 Hz), PAL (AC 220V, 50Hz)

34W

Removable HDD 80GB

BACKUP

VCR VIDEO TAPE

Video Input

Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75Ω)

S-VHS VIDEO

Video Output

Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75Ω)

S-VHS VIDEO

Audio Input

RCA Jack - 1 CH (-8 dBm, 600Ω)

RCA Jack - 1 CH (-6 dBm, 600Ω)

Audio Output

Video Compression Method Motion JPEG

Audio Compression Method G.723 (6.3 Kbps, 2.835 MB/h)

Video Resolution

Picture Quality

720 x 240 [NTSC] 720 x 288 [PAL]

Very High/High/Normal/Low

60 ~ 0.50 Fields/sec [NTSC], 50 ~ 0.50 Fields/sec [PAL]

10, 20, 30 sec, 1, 2, 3, 4, 5 min

RS232, RS485, LAN

350.7mm

Recording Field Rate

Alarm Record Time

Remote Control

Operation Temperature

Storage Temperature

Operating Humidity

Storage humidity

Size

0 °C ~ 40 °C

-20 °C ~ 60 °C

20% ~ 85% RH

20% ~ 95% RH

430(W) x 98(H) x 350.7(D) mm

6.2 Kg

Weight Approx.

98mm

430mm

8-1

8-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Check Points before Call Service Center

If the system malfunctions, please check the following instruction before you call the service

center or the shop where you bought the system.

Trouble

Check Points

Trouble

Check Points

– Check the power cable connection behind the sys-

tem, power supply, and power switch.

• Unable to supply power.

• Abnormal recording and playing after con-

nected to the Multiplexer

– Check the connection between Multiplexer image

output port and system image signal input port and

between Multiplexer image signal input port and

system image signal output port.

• The POWER LED in front of the system

remains off and the system is not running

– Check the power cable connection of the system and

monitor and power supply.

• After power supply, the screen is all black.

• After booting, the screen is all blue

– Check the connection between system trigger output

port(Trigger Out) and Multiplexer.

– Check the connection between camera output port

and system image signal input port and between

monitor image signal input port and system image

signal output port.

– For the details of the Multiplexer, please refer to the

Multiplexer User's Manual.

• No voice during play

– If the AUDIO RECORD in the RECORD MODE

SETUP menu is set to OFF, only images will be

recorded. You should set it to ON to record both

image and voice.

– Check the camera output.

– Check the BNC Cable connected to the system.

– Please call the service center or the shop where you

bought the product for investigation or repair.

• After power supply, no further progress

available after booting menu screen

– No voice will be supplied to the Still screen or Play

mode at high or low speed.

– Check the connection between microphone voice

output port and system voice signal input port and

between monitor voice signal input port and system

voice signal output port.

• No voice

• The screen trembles vertically during play.

• The LIVE screen is distorted.

– Screen trembling often occurs during playing at high

or low speed, which is a normal symptom.

– Appropriate input signals need to be connected for

each model. Connect NTSC signals to the SCR-

3000N/SSC-Dual model and PAL signals to the

SCR-3000P model, otherwise video output may be

disrupted.

– Check the voice signal output.

– Check the connected cable.

– Without input signal, the system can't perform

recording. Please check if the camera output port is

well connected.

• Unable to record.

REC

• The RECORD button (

recording.

) can't activate

–

Make sure that the path between the remote control

and the IR sensor is not obstructed. Also, check the

angle of the remote control with respect to the IR

sensor and the distance between the remote control

and the IR sensor.

– As long as the free HDD space ratio remains 0%

and the FULL indicating LED in front the of system

remains on, the system will not start recording.

– To start recording as it is like above, you should set

the DISK END MODE in the RECORD MODE

• The remote control does not work.

–

Make sure the remote control's batteries have

sufficient power.

SETUP menu to OVERWRITE and press the

REC

RECORD / button(

– To start recording while the DISK END MODE is set

to STOP, you should set the HDD ERASE in SYS-

TEM SETUP menu to ON and terminate the menu.

Then, all the current data will be deleted. Now, you

REC

should press the RECORD button(

) to start

recording. However, as the deleted data can not be

recovered by all means, you should check again

before deleting.

9-1

9-2

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL VIDEO RECORDER

Q & A

Question

Answer

• Does recording continues after power cut

during recording.

– Without power supply, the system can't perform

recording. But if the system was recording before

power cut, it will resume recording upon power sup-

ply.

• What would become of the system if dis-

connected with the input image signal dur-

ing recording?

– Without connection with the input image signal, the

system can't keep recording. But the system will

resume recording upon the supply of normal input

image signal.

• What shall I do to stop recording manually

while the system is detecting movements or

in recording mode as set by the alarm.

• When system is in Reservation Recording

state, how to stop the recording intentional-

ly?

– Press the STOP button (ꢀ) for 3 seconds.

Then, recording will be paused for 5 seconds and

you shall enter the menu to change the recording

setup in the meantime. If you want to stop the alarm

recording, you shall set the ALARM SIGNAL

DETECTION of the ALARM RECORD SETUP

menu to OFF. If you want to stop the reserved

recording, you shall set the TIMER of the TIMER

RECORD SETUP menu to OFF. Without your

action against the system for 5 seconds, the system

will return to the previous mode.

www.securitysamsung.com

• May I use an itentical IP Address for more

than 2 systems?

– Yes, but as long as the 2 systems are not connected

to LAN simultaneously. Connecting the system to

LAN one by one is to be connected to the remote

monitoring program by PC. If you want to connect

the other system to LAN to be connected to the

remote monitoring system by PC, you shall discon-

nect the system currently connected to LAN from

the remote monitoring system by PC and connect

the system to LAN. Then resume connection in at

least one minute. Otherwise, you may not be con-

nected.

• What should I do if I have forgotten the

system's password or ID/password for

network access?

– Turn the hard drive rack's key to the OFF position

and enter the MENU. Then, change the password.

AB68-00406A

Printed in Korea

9-3

Download from Www.Somanuals.com. All Manuals Search And Download.

QUAD Stereo Amplifier II Classic User Guide
Ramsey Electronics Battery Charger LABC1 User Guide
RCA Stereo System 35809 User Guide
RCA TV DVD Combo D34W135D User Guide
Rikaline GPS Receiver GPS 22 User Guide
RocketFish Indoor Furnishings RF TVMFM01 User Guide
Samsung Tablet SM T520NZKAXAR User Guide
Sanyo Air Conditioner 26XH72R User Guide
Scag Power Equipment Lawn Mower STHM User Guide
Schumacher Battery Charger SE 125A User Guide