Thank you for buying a Samsung SYSTEM CONTROLLER.
This manual will guide you through using the SYSTEM CONTROLLER. Please read this manual carefully
before using the SYSTEM CONTROLLER.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Warning
■
All work related to the installation of this appliance must be performed by qualified service personnel or system installers.
- If the product is connected or installed improperly, electric shock, fire, severe injury, and/or damage can result.
■ Please install the product on a completely flat floor.
- Always check the strength and stability of the installation location.
- Do not drop the appliance on the floor. This may result in damage or injury.
■ Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers.
- There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
■ Never use the appliance in places where there are flammable materials.
- Never use the appliance in places where flammable materials such as gas are used.
This may result in fire, explosion, and other serious accidents.
■ Never touch un-insulated parts with wet hands.
- Touching un-insulated parts with wet hands may result in serious electric shock.
■ Never expose the appliance to water or moisture.
- If the appliance gets wet, immediately turn the power off.
- Stop using the appliance if it gets wet. Contact the manufacturer immediately.
■ Stop using the appliance if there appears to be any operational problem.
- Immediately turn the power off to the appliance if there is any abnormal condition such as smoke or unusual smells.
- Continuing to use the appliance under abnormal conditions may result in serious damage.
■ Always use the recommended power.
- Using incorrect power source ratings may result in fire, electric shock, or damage.
■ Always handle the connection cable with care.
- Never damage or modify the connection cable.
- Do not pull, expose to heat, or place heavy objects on the connection cable.
- Non-observance of these warnings may result in fire, electric shock or damage.
Caution
■ Use the appliance indoors only.
- Do not place the appliance outdoors or expose it to rain or moisture.
- If dropped in water, the appliance may be corroded and damaged.
■ Do not use the appliance where there is excessive dust, smoke, or moisture.
- Using the appliance under such conditions may result in fire, electric shock or serious damage.
■ Do not operate the appliance in temperatures beyond those specified.
- Excessive heat or cold may damage the appliance.
- Always operate the appliance within the recommended temperature range of 0˚C ~ 40˚C.
■ Do not place the appliance in direct sunlight.
- This may discolor the appliance.
■ Do not apply excessive shock to the appliance.
- Excessive shock may damage the appliance.
《3》
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Maintenance and Repair
■ If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth.
- Do not use chemical agents such as alcohol or benzene.
■ For detailed information on upgrading the firmware, please direct your inquiries to the installation vendor.
Refer all work related to the installation of this
appliance to qualified service personnel or
system installers.
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference, in which
case the user will be required to correct the
interference at his own expense.
《4》
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Functions and Features
(1) Overview
This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder.
● Speed Dome camera : Samsung Techwin (SPD-1600/2200/2500), PELCO-D, PANASONIC (WV-CS854A),
SAMSUNG ELECTRONICS (SCC-643-641)
● CCTV Receiver : SRX-100B
● DVR : Samsung Techwin (SVR-1630/1620/430)
(2) Features
- It is possible to totally control the 255 Speed Dome camera, CCTV Receiver and Samsung Digital Video Recorder.
- If the Speed Dome is set to one-way reception (RESPONSE OFF), it is possible to connect a maximum of 16 sub-
controllers, including the master controller.
- If the Speed Dome is set to two-way reception (RESPONSE ON), it is possible to connect a maximum of 12 sub-
controllers, including the master controller.
- Camera control with the joystick, zoom buttons, and focus buttons
- Easy camera preset location setup and movement
- Camera control without an operator through automatic operation mode
※Different surveillance cameras may have different names for the same functions, depending on the
manufacturer.Some functions may not be available for certain models.
※If the Speed Dome (SPD-1600/2200/2500) DIP switch is set to one-way reception, each sub-controller can be
controlled independently. If it is set to two-way reception, sub-controllers cannot be controlled independently.
※The SPD-1600/2500 is set to two-way reception and the SPD-2200 is set to one-way reception by factory default.
※Sub-controllers cannot be controlled if the master controller is in use.
Product Components
● SCC-3000 Controller
● Junction Box
● Controller Connection Cable
● Power Adaptor (DC 12V)
● User's Manual
《5》
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
MJ2
u
a
n
s
CctteoioCnBoenocxtriolnleThough SVR1630
n
n
Names and Functions of Each Part
(1) Camera Setup Section
① RESET : Resets camera power.
② PRESET : Moves camera to the preset location (see p.16).
③ LIGHT : Toggles the lights around the camera on and off.
④ AUX : Toggles the camera’s external case AUX on and off.
⑤ TOUR : Sets more than 1 group for tour and performs continuous group action (see p.19).
⑥ SALVO : Not used; will be applied to F/W in the future.
⑦ SWING : Continuously travels between two assigned locations horizontally (pan) or
vertically (tilt) (see p.17).
⑧ GROUP : Repeats sequential surveillance of assigned preset locations with preset
movement rates and intervals (see p.18).
⑨ AF : Sets the focus to automatic or manual after operating the camera (see p.23).
⑩ OSD : Displays the camera OSD menu (see p. 24).
⑪ FUNCTION : Used to perform 2 functions or more at the same time (see p.8).
※ Some buttons in the camera setup section may not be supported or may be used differently depending on the
camera manufacturer. Please refer to the table below for the buttons supported by the major camera manufacturers.
SAMSUNG ELECTRONICS
PANASONIC
(WV-CS854A)
SPD-1600
SPD-2200
SPD-2500
PELCO-D
(SCC-643/641)
RESET
PRESET
TOUR
SALVO
SWING
GROUP
AF
O
O
O
O
O
O
O
O
O
O
O
X
O
O
X
X
O
X
Not used; will be applied to F/W in the future.
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O(AUTO-PAN)
O (AUTO-SEQ)
O (SCAN)
O
O
O
O
O
O
OSD
LIGHT
AUX
Applies only to systems with housing and receivers that support the light function. (SRX-100B only)
Applies only to systems with AUX terminals. (SRX-100B only)
《7》
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Each Part
(2) Number Pad
※ 'F' in the table below refers to the Function button.
① 0 ~ 9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc.
(see p.23).
② F + 0 : Activates the system setup menu (see p.24).
③ ▲ / ▼ : Used for increasing or decreasing menu values in detailed setup menus.
※ When using functions that are performed by a combination of the function button and
numeric keys, the setup may be different depending on the camera manufacturer.
Please refer to the table below for the setup for major camera manufacturers.
PANASONIC
SAMSUNG ELECTRONICS
SPD-1600
SPD-2200
SPD-2500
PELCO-D
(WV-CS854A) (SCC-643/641)
TRACE RUN
(PATTERN)
TRACE RUN
(PATTERN)
TRACE RUN
(PATTERN 1)
F+1
F+2
F+3
F+4
TRACE RUN
TRACE RUN
TRACE RUN
TRACE
TRACE
TRACE
TRACE RUN
(PATTERN 2)
-
-
-
F2(SPECIAL 2)
F3
MEMORY
MEMORY
MEMORY
TRACE RUN
(PATTERN 3)
TRACE
TRACE
TRACE
MEMORY STOP
MEMORY STOP
MEMORY STOP
AUTO
AUTO
AUTO
AUTO-SORT
-
-
POWER ON
POWER ON
POWER ON
AUTO
AUTO
AUTO
F+5
-
-
POWER OFF POWER OFF POWER OFF
※ Use the AUTO POWER ON setting to allow the camera to resume the tasks in its memory upon power supply, even if
they were previously aborted as a result of power failure, etc.
(3) External Device Selectors
① PTZ : Selects the PTZ mode (see p.15~24).
② DVR : Selects the DVR mode (see p.25).
③ CAMERA : Enter camera number and press the CAMERA button to set the camera ID (PTZ mode) or set the channel
(DVR mode).
④ MONITOR : Not used; will be applied to F/W in the future).
《8》
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Each Part
(4) Universal Controller
① ZOOM W/T : Performs camera zoom action (wide and telephoto).
② FOCUS -/+ : Used for manual focus adjustment.
③ || : Used for moving the menu cursor up (when menu is active), pausing DVR
playback, or playing stills.
④ ■ : Used for moving the menu cursor down (when menu is active) or stopping
DVR playback.
⑤ I▶ : Used for moving the menu cursor left (when menu is active) or Slow Playback.
⑥ ▶▶ : Used for moving the menu cursor right (when menu is active) or Fast Playback
⑦ ▶ : Used for playing recorded video.
⑧ REC / ESC : Used for starting surveillance screen recording, canceling entered
values, or moving to the previous stage.
⑨
ENTER / DIR : Used for executing the entered values, performing setups (PTZ mode
and DVR mode), or playing recorded video in the reverse direction.
INFORMATION
It is possible to use all the functions except menu cursor movement of
~
buttons in only PLAY MODE for
●
③
⑨
SVR-900/1620. When the user presses the PLAY MODE button of the controller, PLAY MODE is on.
When PLAY MODE is on, [P-MODE] appears on the LCD monitor. Press the PLAY MODE button once again
to release PLAY MODE.
(5) DVR Controller
※ Please refer to the DVR product manual for the buttons without reference pages.
Some functions may not be supported by certain models.
① QUICK SET : The Quick Setup menu is displayed in the DVR monitor.
② STATUS : The current DVR status is displayed in the DVR monitor.
③ SEARCH : Used for searching the DVR recording list.
④ PLAY MODE : Used for recording and playing the DVR with the controller.
(SVR-900/1620 only)
⑤ MENU : The DVR menu is displayed in the DVR monitor.
⑥ MULTI : Used for switching the DVR monitor from single screen playback mode
to multiple screen playback mode.
⑦ AUTO : displays the sequence of cameras connected to the DVR on the monitor.
⑧ ALRAM RESET : Used for resetting the alarm and event display, turning the relay
on and off, and closing the event notification window.
⑨ LIST : Shows the event list saved in the DVR storage device.
⑩ PIP : Used for performing the PIP (Picture In Picture) function.
⑪ DIGITAL ZOOM : Used for zooming in the monitor screen when in single screen
playback mode.
⑫ FREEZE : Used for pausing the video when displaying a surveillance video.
⑬ SPOT : Used to switch to spot monitor.
⑭ COPY : Used for copying, backing up, or deleting saved video.
⑮ LIVE / PLAY BACK : Used for toggling the surveillance screen and playback screen.
⑯ RELAY : Used for manual control of replay output.
《9》
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Each Part
※ Some DVR controller buttons may not be supported or may be used differently than as described in this manual,
depending on the DVR model. Please refer to the table below for the buttons supported by major DVR model
manufacturers. The DVR button with multiple functions works in the same way on the controller.
SVR-430
SVR-900
SVR-1620
SVR-1630
QUICK SET
STATUS
O
O
O
-
-
-
-
-
O
O
O
O
O
O
O
O
O
O
SEARCH
O
-
PLAY MODE
FOCUS -
O
O
O
-
FOCUS +
O
O
O
II
▶▶
O
O
Jog
Jog(PLAY MODE)
Jog(PLAY MODE)
O
O
Fast Forwarding
(PLAY MODE)
Fast Forwarding
(PLAY MODE)
O
O
O
O
O
Pause
(PLAY MODE)
O
Pause
(PLAY MODE)
O
■
O
O
Jog
O
Slow Playback
(PLAY MODE)
Slow Playback
(PLAY MODE)
I▶
O
O
ENTER / DIR
Direction Switching
(PLAY MODE)
Direction Switching
(PLAY MODE)
O
O
O
O
Record function for
Surveillance (LIVE)
screen
Record function for
Surveillance (LIVE)
screen
Record function for
Surveillance (LIVE)
screen
Record function for
Surveillance (LIVE)
screen
REC / ESC
MENU
MULTI
O
O
O
O
-
O
O
O
O
O
O
AUTO
O
O
O
ALARM RESET
LIST
O
O
O
O
O
-
PIP
O
O
-
O
O
-
DIGITAL ZOOM
FREEZE
SPOT
O
O
O
O
O
-
-
O
O
O (A/B)
COPY
O
O
-
O
O
O
-
LIVE/PLAY BACK
RELAY
Screen Selection
Screen Selection
-
-
O
-
-/+
O
O
O
《10》
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Each Part
(6) Camera Controller
① Joystick: Used for moving the camera up, down, left, and right, and for zoom control (see p.13).
1) Tilt up (Up button): Moves the camera up.
2) Tilt down (Down button): Moves the camera down.
3) Tilt left (Left button): Moves the camera left.
4) Tilt right (Right button): Moves the camera right.
5) Turn stick clockwise: Performs telephoto-zoom.
6) Turn stick counter-clockwise: Performs wide zoom.
② SLOW : Sets the camera movement (up, down, left, and right) speed slow.
③ FAST : Sets the camera movement (up, down, left, and right) speed fast.
[Joystick]
[Camera Control Button]
(7) Junction Box
[Front]
[Back]
DIP Switch
PTZ/DVR
Connector
Power Input
Connector
Sub-Controller
Connector
Junction Box
Connector
Reversed
Connector
《11》
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation
(1) Power-On
① Power on the connected external devices before turning the controller on.
② Press the power button at the back of the controller to power on the controller.
③ The [SYSTEM Controller] message and F/W version will be displayed in the LCD
monitor, and the message will disappear when the controller is ready for use.
▤ The [JOYSTICK ERROR] error will be displayed in the LCD monitor if the
joystick is not placed in the center during power-on.
[ power button ]
(2) Initial Screen Display
① CAM ID : Shows the currently selected camera ID. Default is 1.
② SPD : Shows the currently selected camera model name.
Default is SPD.
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 1ꢀꢀꢀꢀꢀSPD
MONITOR:ꢀꢀ1ꢀꢀꢀꢀ[ꢀ---ꢀ]
ID:ꢀꢀꢀ1
①
③
②
④
③ MONITOR : Not used; will be applied to F/W in the future.
④ [- - -] : Shows the numbers (ID) entered when entering numbers
with the number pad.
⑤
⑤ ID : Shows the current controller ID. If the ID is 1, it acts as the master
controller. If the ID is 2 or higher, it acts as a sub -controller.
Sub-controllers cannot be used independently without a master
controller.
▤ Always assign a unique ID to ensure that the controller IDs do not
conflict with each other.
▤ SPD : SPD-1600/ SPD-2200/ SPD-2500(Samsung Techwin Co., Ltd.)
(3) Camera ID Setup
① Enter a number using the number pad.
② The number entered will be shown in the [- - -] display.
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 1ꢀꢀꢀꢀꢀSPD
MONITOR:ꢀꢀ1ꢀꢀꢀꢀ[ꢀ5ꢀ]
Enter:PTZꢀIDꢀSet
③ Press the CAMERA or ENTER button to set the camera ID with the
number entered.
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
MONITOR:ꢀꢀ1ꢀꢀꢀꢀ[ꢀ---ꢀ]
ID:ꢀꢀꢀ1
▤ Any number from 1 to 255 can be selected. If the number entered is
not within the selectable range, the last entered number is taken as
the first number.
《12》
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation
(4) Joystick/Camera Control Button
■ The joystick can be used to control the camera’s left and right (pan) and up and down (tilt) movements.
■ The joystick can be used to control camera zoom functions.
[Camera wide zoom]
[Camera telephoto zoom]
《13》
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation
(5) Camera Movement Speed Control
■ Use the joystick or press the Slow/Fast button at the bottom of the
camera control button section to adjust the camera movement speed.
▤ You must press the ESC button after adjusting the camera
movement speed in order to be able to use other controller buttons.
[SLOW/FAST button]
▤ The SLOW/FAST button can be used to adjust movement speed
for models without a joystick.
(6) Camera Zoom Control
■ Press the ZOOM W/T button to control zoom wide and zoom telephoto.
ZOOM W : Zoom Wide
ZOOM T : Zoom Telephoto
[ZOOM W/T button]
(7) Camera Focus Control
■ Press the FOCUS -/+ button to control camera focus.
FOCUS - : Focus gets nearer.
FOCUS + : Focus gets further.
▤ The FOCUS -/+ button can be used as the ENTER/ESC button for
the SVR-1630 and SPD series.
[FOCUS -/+ button]
《14》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(1) PTZ Setup Mode
■ This menu is for setting up the PTZ camera function.
It is impossible to operate Speed Dome and DVR by sub-controllers
when the master controller is set to on.
① At the initial screen, press the Function button and press the 0 button
SETUPꢀSYSTEM
2:DVR
to activate the [SETUP SYSTEM] menu.
1:PTZ
3:CONTROLLER
PressꢀNumericꢀKey
② Press the 1 button to activate the [PTZ SETUP 1 ▶] menu.
PTZꢀꢀSETUPꢀꢀ1
1:PRESET
3:GROUP
2:SWING
4:TOUR
PressꢀꢀꢀNumericꢀꢀꢀKey
③ Press the ▶▶ button to activate the [◀ PTZ SETUP 2] menu.
PTZꢀꢀSETUPꢀꢀ2
1:MODEL
3:AF
PressꢀꢀNumericꢀꢀKey
2:TRACE
INFORMATION
The menu may be different depending on the PTZ camera model.
●
Menu
Menu
Models supported
Models supported
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
MODEL
PRESET
SPD series, PELCO-D,
PANASONIC
SWING
SPD series
TRACE
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
GROUP
TOUR
SPD series
SPD series
AF
-
-
Press the ESC button to move to an upper setup mode.
●
《15》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(2) PRESET
■ This menu is for setting the camera to move to preset locations.
(2-1) PRESET Setup
① At the [PTZ SETUP 1 ▶] menu, press the 1 button (see p.15).
PTZꢀꢀSETUPꢀꢀ1
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
PRESETꢀNO:ꢀꢀꢀ0
② Use the joystick or camera control button (SCC-3000 model) to move
the camera to the desired location (move up, down, left, and right, and
control zoom).
Enter:PresetꢀIDꢀSet
③ Enter a preset number.
PTZꢀSETUPꢀ1
CAMꢀID:ꢀꢀꢀꢀ5ꢀꢀꢀꢀSPD
PRESETꢀNO:ꢀꢀꢀ1
Enter:PresetꢀIDꢀSet
④ Press the Enter button to assign the number to the current location.
(2-2) PRESET Movement
① In the initial screen, enter an assigned preset number.
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
MONITOR:ꢀꢀ1ꢀꢀꢀꢀ[ꢀꢀ1ꢀ]
Enter:PTZꢀꢀIDꢀꢀSet
② The selected number will be shown in the [- - -] display.
③ Press the Preset button to move the camera to the preset location.
▤ If the number entered is not within the selectable range, the last
entered number is taken as the first number.
The selectable range for each camera model is as follows.
● SPD 1600/2200/2500 : 1 ~ 64
● PELCO-D : 1 ~ 80
Certain numbers have special functions other than preset.
33 + PRESET - FLIP COMMAND
97 + PRESET - RANDOM SCAN
98 + PRESET - FRAME SCAN
99 + PRESET - AUTO SCAN
See the camera manual for more information.
● PANASONIC (WV-CS854A) : 1 ~ 64
● Samsung (SCC-641/643) : 1 ~ 127
▤ Preset setup is also available in the OSD menu of the connected
camera.
《16》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(3) SWING
■ This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt).
Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other
manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more
information.
(3-1) SWING Setup
① At the [PTZ SETUP 1 ▶] menu, press the 2 button (see p.15).
SWINGꢀSETUP
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
② Press the 1 or 2 button to select a horizontal (pan) or vertical (tilt) cycle.
1:PANꢀSET
2:TILTꢀSET
PressꢀNumericꢀKey
③ Set starting point, ending point, movement speed, and stop time.
- I▶/▶▶ button: Moves between items.
SWINGꢀSETUP
IST 2ND SPEED STOP
- 1ST : Starting point. Can be set for Preset 1 ~ 64.
- 2ND : Ending point. Can be set for Preset 1 ~ 64.
- SPEED : Movement speed. Can be set for 1 ~ 64 (see p.35).
- STOP : Stop time at the starting point and ending point.
Can be set to 1 ~ 99 (seconds).
00
00 00
Enter:SwingꢀSet
00
④ Press the ENTER button to finish the setup (takes 2 or 3 seconds to
finish).
▤ The Swing function cannot be set if an unassigned number or a
number outside the selectable range is entered.
▤ Over 2 PRESET locations have to be set before setting SWING.
(3-2) SWING Operation
① At the initial screen, press the Swing button.
② Press the 1 and 2 buttons to perform the Swing function.
- 1 button: Performs the horizontal cycle (pan).
- 2 button: Performs the vertical cycle (tilt).
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
1:PAN 2:TILT
PressꢀꢀꢀNumericꢀꢀꢀKey
▤ Move the joystick or press a controller button during the Swing
operation to stop the operation.
▤ AUTO-PAN is performed automatically when the SWING button of
PANASONIC(WV-CS854A) and SAMSUNG ELECTRONICS
(SCC-641/643) cameras is pressed.
《17》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(4) GROUP
■ This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals.
Setting the GROUP SETUP menu by controllers is only available for an SPD series. In case of products by other
manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more
information.
(4-1) GROUP Setup
① At the [PTZ SETUP 1 ▶] menu, press the 3 button (see p.15).
GROUPꢀSETUP
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
② Enter a Group number.
GROUPꢀSETꢀNUM?ꢀ<1-6>
▤ Any number between 1 and 6 can be selected.
PressꢀꢀꢀNumericꢀꢀꢀKey
③ Set each location’s Preset ID, area movement speed, and stop time.
GROUPꢀSETUP
NO PRESET SPEED STOP
- I▶/▶▶ button: Moves between items.
- NO : Setup sequence. Up to 64 can be selected.
01
Enter:Nextꢀ
0
00 00
Group:Set
▤ In the case of SPD 2200, setup via the controller is up to 64, but via
the camera OSD menu it can be up to 128.
- PRESET : Camera Preset ID for assigned location.
- SPEED : Area movement speed. Can be set from 1 ~ 64 (see p.35).
- STOP : Stop time at the starting point and ending point.
Can be set to 1 ~ 99 (seconds).
④ Press the ENTER button to move to the setup page for the next location.
Press the Group button to finish the Group Setup.
▤ The Group function cannot be set if an unassigned number or a
number outside the selectable range is entered.
▤ Over 2 PRESET locations have to be set before setting GROUP.
(4-2) GROUP Operation
① At the initial screen, press the Group button.
② Press the Group button to execute the operation.
③ The Group function is performed.
PTZꢀCONTROLꢀSYSTEM
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
GROUPꢀRUNꢀNUM?ꢀ<1-6>
PressꢀꢀꢀNumericꢀꢀꢀKey
▤ AUTO-SEQ and SCAN functions are performed when the GROUP
button is pressed (for PANASONIC(WV-CS854A) and SAMSUNG
ELECTRONICS (SCC-641/643 only).
《18》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(5) TOUR
■ This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out.
The TOUR SETUP menu is only available for an SPD series.
(5-1) TOUR Setup
① At the [PTZ SETUP 1▶] menu, press the 4 button (see p.15).
TOURꢀSETUP
1ꢀꢀGROUPꢀNUM?ꢀ<1-6>
② Press a Group number to add to the Tour.
Enter:TourꢀSet
▤ Up to 6 Groups can be added.
③ Press the ENTER button to finish the setup.
(5-2) TOUR Operation
① At the initial screen, press the Tour button.
② The Tour function is performed.
▤ The TOUR operation is only available for an SPD series.
《19》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
TOUR
GROUP 1
GROUP 3
《20》
PTZ Mode
(6) MODEL
■ This menu is for setting the PTZ camera ID and camera type.
① At the [PTZ SETUP 1▶] menu, press the ▶▶ button (see p.15).
PTZꢀꢀSETUPꢀꢀ2
1:MODEL 2:TRACE
3:AF
PressꢀNumericꢀKey
② Press the 1 button to move to the Model Setup screen.
③ Press a number in the number pad to set the PTZ camera ID.
The camera model type saved in EEPROM is displayed on the LCD monitor when changing camera ID.
PTZꢀMODELꢀSETUP
PTZꢀ ID:ꢀ 0ꢀꢀꢀꢀ[ꢀꢀ0ꢀ]
MODEL:NONE
PTZꢀMODELꢀSETUP
PTZꢀ ID:ꢀ 1ꢀꢀꢀꢀ[ꢀꢀ1ꢀ]
MODEL:ꢀꢀꢀꢀSPD
When
+,
-
:ModelꢀChange
+,-:ModelꢀChange
entering '1'
④ Press the + and - buttons on the number pad to change the camera type. SPD-1600/2200/2500, PELCO-D,
PANASONIC(WV-CS854A) and SAMSUNG ELECTRONICS (SCC-643) types can be selected.
⑤ Press the ENTER button to finish the setup.
《21》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(7) TRACE
■ This menu is for inputting camera movements, through joystick or camera control buttons, into the memory for a
certain period of time, to allow repeating of stored movements when performing the Trace (PATTERN) function.
Setting the TRACE SETUP menu by controller is only available for an SPD series.
In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera.
See the camera manual for more information.
(7-1) TRACE Memory
① At the [PTZ SETUP 1 ▶] menu, press the ▶▶ button (see p.15).
PTZꢀꢀSETUPꢀꢀ2
1:MODEL
3:AF
2:TRACE
② Press the 2 button to move to the Trace Setup screen.
PressꢀNumericꢀKey
③ Press the 1 button.
PTZꢀTRACEꢀSETUP
1:RECORD
2:PLAYꢀ
PressꢀNumericꢀKey
④ Use the joystick or camera control buttons to perform the camera
movement to input. Allowed movements are horizontal movements
(pan), vertical movements (tilt), zoom, and focus controls.
PTZꢀTRACEꢀRECORDING
RECꢀSTOP:PRESSꢀENTER
⑤ Press the ENTER button to stop camera movement input.
▤ Maximum length for movement memory is approximately 60 ~ 105
seconds. This may vary according to free memory space.
▤ Movement memory length may be shorter if the camera movement
is more complicated.
▤ Press the FUNCTION button and the 2 button to start TRACE
memory.Press the FUNCTION button and the 3 button to stop
TRACE memory. For more information, see p. 8.
(7-2) TRACE Operation
① At the Trace Setup screen, press the 2 button.
PTZꢀTRACEꢀSETUP
1:RECORD
2:PLAYꢀONCEꢀꢀ3:DELETE
PressꢀNumericꢀKey
《22》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(8) AF (Auto-Focus)
■ This menu is for adjusting camera focus manually or automatically after
camera operation. If AF is set to OFF in the camera setup menu, set the
AF of the controller to ON and then automatic adjustment is performed
after camera operation.
① At the [PTZ SETUP 1▶] menu, press the ▶▶ button (see p.15).
PTZꢀꢀSETUPꢀꢀ2
1:MODEL 2:TRACE
3:AF
PressꢀNumericꢀKey
② Press the 3 button to move to the AF Setup screen.
③ Press the 1 button to automatically adjust the focus after camera
operation. Press the 2 button to disable automatic focus adjustment
after camera operation.
AFꢀSTOPꢀSETUP
CAMꢀID:ꢀ 5ꢀꢀꢀꢀꢀSPD
1:AFꢀON 2:AFꢀOFF
PressꢀNumericꢀKey
▤ Auto Focus Setup is also available in the OSD menu of the camera
connected.
▤ It is recommended that you set up the AF function through the
camera OSD menu.
《23》
Download from Www.Somanuals.com. All Manuals Search And Download.
PTZ Mode
(9) OSD
■ This is used for displaying the camera menu on the monitor.
① At the initial screen, press the OSD button.
② Use the controller buttons to set up the camera menu.
- OSD : SPD 1600/2200/2500 - Toggle camera menu on/off (hold down for 2
seconds)
PELCO-D - Toggle camera menu on/off (press ESC)
PANASONIC (WV-CS854A) - Toggle camera menu on/off (press ESC)
Samsung (SCC-643/641) - Toggle camera menu on/off (press ESC)
- ESC : Cancels the menu selection.
- ENTER : Selects the menu.
- ▶▶ : Moves the menu cursor right.
- I ▶ : Moves the menu cursor left.
Applies to PANASONIC models only
- II : Moves the menu cursor up.
- ■ : Moves the menu cursor down.
- Joystick : Use the joystick to move the menu cursor up, down, left, and
right.(Applies to SPD, PELCO-D and Samsung models only:)
▤ Joystick or other button inputs cannot be used for camera operation when the
camera menu is displayed on the monitor.
▤ PRESET, SWING, GROUP, and TRACE functions can be set in the OSD menu
of the camera.
▤ Please refer to the camera manual for more information on the camera menu.
▤ When operating the PTZ camera OSD menu while the controller and SVR-1630
are connected, the ENTER and ESC functions can only be performed by the
FOCUS -/+ button.
《24》
Download from Www.Somanuals.com. All Manuals Search And Download.
DVR Mode
DVR MODEL Setup
■ This menu is for setting the DVR ID and model for operation by a
controller. Sub-controllers cannot be used if the master controller is
in Setup mode.
① At the initial screen, press the FUNCTION button and press the 0 button
SETUPꢀSYSTEM
2:DVR
to activate the [SETUP SYSTEM] menu.
1:PTZ
3:CONTROLLER
PressꢀNumericꢀKey
② Press the 2 button to activate the [DVR SETUP] menu.
DVRꢀSETUP
1:DVRꢀMODELꢀSETUP
PressꢀNumericꢀKey
③ Press the 1 button to activate the [DVR Model SETUP] menu.
DVRꢀMODELꢀSETUP
DVRꢀ ID:ꢀ 0ꢀꢀꢀꢀ[ꢀꢀ0ꢀ]
MODEL:ꢀNONE
④ Press a number on the number pad to set the DVR ID.
The DVR model name saved in EEPROM will be displayed on the LCD
monitor when changing DVR ID.
+,-:ModelꢀChange
When entering '1'
⑤ Press the + and - buttons to change the DVR model name
DVRꢀMODELꢀSETUP
DVRꢀ ID:ꢀ 1ꢀꢀꢀꢀ[ꢀꢀ1ꢀ]
MODEL:ꢀSVR430
(SVR 430 → SVR 900 → SVR 1620 → SVR 1630).
+,-:ModelꢀChange
⑥ Press the ENTER button to finish the setup.
▤ When connecting to an SVR-430, the SVR-430 system ID must be set to be the same as the controller DVR ID
(Menu → Network/Communication → RS422/485 → SYSTEM ID).
▤ When connecting to an SVR-900/1620, the SVR-900/1620 system ID must be set to be the same as the
controller DVR ID (Menu → System Setup → Com Port Setup → SYSTEM ID).
▤ When connecting to an SVR-1630, the SVR-1630 keyboard control address must be set to be the same as the
controller DVR ID (Menu → System Setup → Misc.). Also, for the SVR-1630 COM2 RS422/485 menu (Menu →
System Setup → Serial Port), Device must be set to SCC-3000 and Interface to RS-485, and for the COM4
RS422/485 menu (Menu → System Setup → Serial Port), Device must be set to SPD2500 (if an SPD2500 is
connected) and Interface to RS-485.
▤ When controlling a PTZ camera via an SVR-1630, connect the SVR-1630 and the controller to COM2 RX+/RX-
and connect the SVR-1630 and PTZ camera to COM4 RX+/RX-. Also, at the SVR-1630 channel setup menu, set
the PTZ port of each channel to COM4 and set the PTZ address to be the same as the PTZ camera ID.
《25》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(1) Controller Setup Mode
■ Sub-controllers cannot be operated if the master controller is in setup mode.
① At the initial screen, press the FUNCTION button and press the 0 button
SETUPꢀSYSTEM
2:DVR
to activate the [SETUP SYSTEM] menu.
1:PTZ
3:CONTROLLER
PressꢀNumericꢀKey
② Press the 3 button to activate the [Controller SETUP 1 ▶] menu.
③ Press the ▶▶ button to activate the [◀Controller SETUP 2 ▶] menu.
④ Press the ▶▶ button to activate the [▶ Controller SETUP 3] menu.
CONTROLLERꢀSETUP1
1:CONTROLLERꢀID
2:SERIAL
3:COPY
PressꢀNumericꢀKey
CONTROLLERꢀSETUP2
1:RESPONSE
2:PASSWORD
PressꢀNumericꢀKey
CONTROLLERꢀSETUP3
1:PRIORITY
2:DEFAULT
⑤ At the [Controller SETUP 1 ▶], [◀ Controller SETUP 2 ▶] or
[◀ Controller SETUP 3] menu, press a menu number to open a setup
menu.
3:F/WꢀUPDATE
PressꢀNumericꢀKey
INFORMATION
Press the ESC button to move to the upper setup mode.
●
●
The Controller Setup menu can be added to enhance controller functionality.
《26》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(2) Controller ID Setup
■ This menu is for setting controller ID.
① At the [Controller SETUP 1 ▶] menu, press the 1 button (see p.26).
CONTROLLERꢀSETUP1
1:CONTROLLERꢀID
2:SERIAL
3:COPY
PressꢀNumericꢀKey
② Press a number on the number pad to enter a controller ID.
③ Press the ENTER button to set the controller ID.
CONTROLLERꢀIDꢀSET
CONTROLLERꢀID:ꢀꢀ1[ꢀꢀ0ꢀ]ꢀ
IDꢀ1ꢀISꢀMASTERꢀID!
▤ Assign number 1 for setting the controller ID for the master controller.
▤ The lower the ID number, the higher the controller priority.
▤ Sub-controllers can be operated only when connected to a master
controller; Sub-controllers cannot be operated independently.
Enter:IDꢀSetꢀ<1-16>
(3) SERIAL Setup
■ This menu is for setting the serial port for connecting external devices to the controller.
① At the [Controller SETUP 1 ▶] menu, press the 2 button (see p.26).
CONTROLLERꢀSETUP1
1:CONTROLLERꢀID
2:SERIAL
3:COPY
PressꢀNumericꢀKey
② Press the 1 button to activate the Serial 1 PORT Setup screen (PTZ
camera/DVR connection PORT). Press the 2 button to activate the
Serial 2 PORT Setup screen (reserved PORT).
RS 422/485ꢀSET
1:S1ꢀꢀ9600,ꢀ8,ꢀ1,ꢀNONE
2:S3ꢀꢀ9600,ꢀ8,ꢀ1,ꢀNONE
PressꢀNumericꢀKey
▤ The value displayed at step ② indicates the current setup value.
▤ The BAUD RATE/ DATA BIT/ STOP BIT/ PARATY BIT for PORT
2, which connects to the sub-controller, are fixed and cannot be
changed.
③ The PORT Setup screen will be displayed.
Press the number for a setup menu.
RS 422/485ꢀSET
1:BUAD
2:DATA
1: Sets the BAUD RATE. (4800, 9600, 19200, 38400)
2: Sets the DATA BIT. (8BIT, 7BIT)
3:STOPꢀBIT 4:PARITY
PressꢀNumericꢀKey
3: Sets the STOP BIT. (1BIT, 2BIT)
4: Sets the PARITY BIT. (NONE, ODD, EVEN)
▤ Default values for controller SERIAL are 9600 (BAUD RATE), 8BIT
(DATA BIT), 1BIT (STOP BIT) and NONE (PARITY BIT).
《27》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(4) DATA COPY
■ This menu is for copying master controller menu data to a sub-controller.
The controller ID value is not copied.
① At the [Controller SETUP 1▶] menu, press the 3 button (see p.26).
CONTROLLERꢀSETUP1
1:CONTROLLERꢀID
2:SERIAL
3:COPY
PressꢀNumericꢀKey
② Press a number on the number pad to enter the ID number for the sub-
DATAꢀCOPY
SUB-CONTROLꢀID?ꢀ[ꢀꢀ0ꢀ]
controller where the data will be copied.
Enter:IDꢀSetꢀ<2-16>
③ Press the ENTER button to set the controller ID.
DATAꢀCOPY
DoꢀyouꢀwantꢀtoꢀCOPY?
1:YESꢀꢀ2:NOꢀSUB ID:ꢀ2
PressꢀNumericꢀKey
④ Press the 1 button to start coping data.
-
Press the 2 button to return to the previous menu.
⑤ The [DATA COPYING SUCCESS] message appears when data copying is complete.
The [DATA COPYING FAIL] message appears if data copying failed.
DATAꢀCOPY
WaitꢀaꢀMinute
DATAꢀCOPYINGꢀSUCCESS
PressꢀNumericꢀKey
DATAꢀCOPY
WaitꢀaꢀMinute
DATAꢀCOPYINGꢀFAIL
PressꢀNumericꢀKey
[DATA COPY SUCCESSFUL]
[DATA COPY FAILURE]
▤ Data copy takes approximately 7~10 seconds.
This menu is available only for the master controller (ID: 1).
《28》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(5) RESPONSE
■ If the camera RESPONSE is set to two-way reception (RESPONSE ON), the controller RESPONSE menu must be
set to ON. If the camera RESPONSE is set to one-way reception (RESPONSE OFF), the controller RESPONSE
menu must be set to OFF.If this is not followed, the system may have a configuration conflict.For more information on
the camera RESPONSE settings, direct your inquiries to the installation vendor. If the DIP switch for the camera
connected to the controller is set to two-way reception (RESPONSE ON), this menu can be used to set up the
RESPONSE value for the controller and the number of sub-controllers.
① At the [Controller SETUP 1 ▶] menu, press the ▶▶ button (see p.26).
CONTROLLERꢀSETUP2
1:RESPONSE
2:PASSWORD
② Press the 1 button to open the Response Setup screen.
PressꢀNumericꢀKey
③ Press the 1 button to set the controller RESPONSE setting to ON.The
RESPONSEꢀTYPEꢀSETUP
controller automatically restarts to apply the change.Press the 2 button
1:ON
2:OFF
to set the controller RESPONSE setting to OFF.The master controller
display shows the setup screen for the number of the connected sub-
controller.
PressꢀNumericꢀKey
④ Press the 1 ~ 4 button to set the number of the desired sub controller.
The controller automatically restarts to apply the changed settings after
entering the number.
RESPONSEꢀTYPEꢀSETUP
1:MAX-4
3:MAX-12
2:MAX-8
4:MAX-16
PressꢀNumericꢀKey
- 1: Sets the number of sub-controllers to 4 including the master controller.
- 2: Sets the number of sub-controllers to 8 including the master controller.
- 3: Sets the number of sub-controllers to 12 including the master controller.
- 4: Sets the number of sub-controllers to 16 including the master controller.
▤ Set the maximum number of sub-controllers, to shorten the sub
controller data loading time by making the master controller
memorize the number of sub-controllers.
▤ If Response is set as ON, a maximum of 12 sub-controllers only can be selected.
《29》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
▤ For information on camera RESPONSE settings (DIP switch settings), refer to the camera manual.
(5-1) SPD-1600 DIP Setup
ON
OFF
DIP-SW 1
DIP-SW 2
DIP-SW 3
DIP-SW 4
Not used
Reserved
Always OFF
Always OFF
RESPONSE Setup
Factory default
HALF DUPLEX FULL DUPLEX
Always OFF
[ RESPONSE ON Setup ]
(5-2) SPD-2200 DIP Setup
ON
RESPONSE Setup FULL DUPLEX HALF DUPLEX
Always OFF
OFF
DIP-SW 1
DIP-SW 2
DIP-SW 3
DIP-SW 4
Reserved
Termination setting Refer to the camera user manual
[ RESPONSE ON Setup ]
(5-3) SPD-2500 DIP Setup
ON
OFF
Always OFF
Always OFF
DIP-SW 1
DIP-SW 2
DIP-SW 3
DIP-SW 4
Not used
Reserved
HALF DUPLEX FULL DUPLEX
Always OFF
RESPONSE Setup
Factory default
[ RESPONSE ON Setup ]
《30》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(6) PASSWORD
■ This menu is for setting the password to enter when changing controller setup values upon power-on.
(6-1) PASSWORD Setup
① At the [Controller SETUP 1▶] menu, press the ▶▶ button (see p.26).
CONTROLLERꢀSETUP2
1:RESPONSE
2:PASSWORD
② Press the 2 button to activate the Password Setup screen.
PressꢀNumericꢀKey
③ Press the 1 button to activate the Password Setup screen.
PASSWORDꢀSETUP
1:PASSWORDꢀSETUP
2:MENUꢀON 3:POWERꢀON
PressꢀNumericꢀKey
④ Use the number pad to enter a 6-digit password.
PASSWORDꢀSETUP
INPUTꢀPASSWORD
[ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ]
PressꢀNumericꢀKey
⑤ The password verification screen will appear.
PASSWORDꢀSETUP
RE-INPUTꢀPASSWORD
[ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ]
Re-enter the same password. The password will be saved.
PressꢀNumericꢀKey
▤ The factory default password is ****.
Please change the password after installation.
《31》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(6-2) Applying Password – Setup Mode
① At the Password Setup screen, press the 2 button.
PASSWORDꢀSETUP
1:PASSWORDꢀSETUP
2:MENUꢀON 3:POWERꢀON
PressꢀNumericꢀKey
② Press the 1 button to ask for a password every time the setup mode is
PASSWORDꢀSETUP
1:MENUꢀPASSWORDꢀON
2:MENUꢀPASSWORDꢀOFF
PressꢀNumericꢀKey
selected. Press the 2 button to skip asking for a password.
(6-3) Applying Password - Power
① At the Password Setup screen, press the 3 button.
PASSWORDꢀSETUP
1:PASSWORDꢀSETUP
2:MENUꢀON 3:POWERꢀON
PressꢀNumericꢀKey
② Press the 1 button to ask for a password every time the appliance is
PASSWORDꢀSETUP
1:POWERꢀPASSWORDꢀON
2:POWERꢀPASSWORDꢀOFF
PressꢀNumericꢀKey
powered on. Press the 2 button to skip asking for a password.
(6-4) Entering Password
If a password is set, the password has to be entered every time the
appliance is powered on or before entering the setup menu. At the screen
as illustrated on the right, enter the password set at step (6-1).
PASSWORDꢀSETUP
INPUTꢀPASSWORD
[ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ]
PressꢀNumericꢀKey
《32》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(7) PRIORITY
■ This menu is for setting the connected sub-controller to use a PTZ camera or DVR within the specified restrictions.
This menu is available for master controller (ID: 1) only.
① At the [Controller SETUP 1 ▶] menu, press the ▶▶ button twice
CONTROLLERꢀSETUP3
1:PRIORITY 2:DEFAULT
3:F/WꢀUPDATE
(see p.26).
② Press the 1 button to activate the Priority Setup screen.
PressꢀNumericꢀKey
③ Press the 1 button to activate the PTZ Camera Restriction Setup menu.
PRIORITYꢀSETUP
1:PTZꢀIDꢀLIMIT
Press the 2 button to activate the DVR Restriction Setup menu.
2:DVRꢀIDꢀLIMIT
PressꢀNumericꢀKey
④ Use the controller button to set the menu.
[ID]: ID of the assigned sub-controller.
Left [000-255] : The currently selected restriction ID.
Right [000-000] : ID to be assigned.
- I▶/▶▶ : Moves items left and right.
- 2 ~ 16 : Enters ID number.
PTZꢀIDꢀLIMIT
IDꢀꢀꢀꢀꢀLIMITEDꢀRANGE
02ꢀꢀꢀ000-255ꢀꢀꢀꢀꢀ000-000
Esc:ExitꢀꢀꢀꢀEnter:Set
[PTZ Camera Restriction Setup Menu]
- ESC : Moves to the upper menu.
- ENTER : Finishes setup.
DVRꢀIDꢀLIMIT
IDꢀꢀꢀꢀꢀLIMITEDꢀRANGE
02ꢀꢀꢀ000-255ꢀꢀꢀꢀꢀ000-000
Esc:ExitꢀꢀꢀꢀEnter:Set
[DVR Restriction Setup Menu]
《33》
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller Mode
(8) DEFAULT
■ This menu is for resetting the changed controller setup values to the default values.
① At the [Controller SETUP 1 ▶] menu, press the ▶▶ button twice
CONTROLLERꢀSETUP3
1:PRIORITY 2:DEFAULT
3:F/WꢀUPDATE
PressꢀNumericꢀKey
(see p.26).
② Press the 2 button to open the Default Setup screen.
③ Press the 1 button to change the controller setup values to the default
values and restart the controller.
DEFAULTꢀSETUP
DEFAULTꢀSETꢀNOW?
1:YES 2:NO
PressꢀNumericꢀKey
Press the 2 button to cancel the process.
《34》
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
(1) Swing, Group Movement Speed
▤ For Swing setup, the speed setup value can be 240˚/second for pan, and 180˚/second for tilt.
Setup value
Degrees / second
Setup value
33
Degrees / second
Setup value
Degrees / second
Setup value
33
Degrees / second
1
2
3
4
5
6
7
8
9
0.8
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
23
24
25
26
27
28
29
30
35
1
0.8
1.0
1.5
2.0
2.5
3.0
3.5
4.0
23
24
34
2
34
35
3
35
25
36
4
36
26
37
5
37
27
38
6
38
28
39
7
39
29
40
8
40
30
41
921.19
Tm0.1(41
)-1155
37
《35》
REFERENCE
(2) System Connections
(2-1) Connecting Controller and Junction Box
(2-2) Connecting Junction Box and External Devices
JUNCTION BOX
[SUB JUNCTION BOX]
RX+ RX- TX+ TX-
RX+ RX- TX+ TX-
RX+ RX- TX+ TX-
X
X
X
X
X
X
X
X
X
X
X
X
RX+
RX- GRD TX+
TX-
RX+
RX-
RX+
RX-
X
X
X
X
X
X
X
X
X
[SVR-1630 connection] [PTZ connection]
*RX+=DATA+
RX- =DATA-
[SVR-430/900/1620 connection]
* RX+ and TX+ / RX- and
TX- must be short-circuited.
▤ When connecting with an SVR-1630, only SPD series PTZ cameras can be employed.
▤ When controlling a PTZ camera via an SVR-1630 there is a delay, and the response may be slow.
▤ When controlling a PTZ camera with a sub-controller there is a delay, and the response may be slow.
《36》
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
(3) RS-485/422 Pin Layout (D_SUB_FEMALE)
Terminal
Name
5
1
1
2
+12V
RX+ (RS-485+)
PORT1
PORT1
PORT1
PORT1
3
RX- (RS-485-)
4
TX-
15
11
5
TX+
6
-
7
RX+ (RS-485 +)
RX- (RS-485 -)
TX-
PORT2
PORT2
PORT2
PORT2
8
9
10
11
12
13
14
15
TX+
GND
RX+ (RS-485 +)
RX- (RS-485 -)
TX-
PORT3
PORT3
PORT3
PORT3
TX+
(4) RS-232C Pin Layout (D_SUB_MALE)
Terminal
Name
1
6
5
9
1
2
3
4
5
6
7
8
9
-
RX
TX
-
GND
-
-
-
-
《37》
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
(5) Controller Specifications
MODEL
SCC-3000
Power (Consumption)
Control
12VDC(Max 700mA)
DVR & Speed Dome (SPD-2500, 1600, 2200)
SPD-2500, 1600, 2200 all function control
- DVR : SVR-1620 / 900 / 430 / 1630 / 1650
- PTZ : SEC, PELCO-D, PANASONIC
RS-485 / RS-422
PTZ Control
Compatibility
Remote Control
Connector
3Port
Baud Rate (bps)
LCD Display
Max 38400bps (Sub-controller : 56400bps)
20 x 4 Character LCD
PTZ Control
Joystick (3Axis Twist Zoom)
Flow control connected with Master Keyboard
Tour, Group, Swing, Preset
0 ~ 40°(10% ~ 75%)
Sub Keyboard
Auto Surveillance
Operating temperature(Humidity)
Storage temperature(Humidity)
Weight
-5 ~ 55°(10% ~ 95%)
2kg
Dimension
400mm X 180mm X 45mm (Without Joystick' height)
(6) RS-485/422 Specifications
Type
Asynchronous Serial, 1 START BIT, 8 DATA BIT, NO PARITY,1 STOP BIT
HALF DUPLEX / FULL DUPLEX
Transmission method
Transmission rate
Composition
4800 ~ 38400 (9600bps recommended)
4 lines (Twist pair)
(7) Junction Box DIP Switch
● RS-485 Termination ON
● RS-422 Termination ON
● RS-485 Termination OFF
● RS-422 Termination OFF
《38》
Download from Www.Somanuals.com. All Manuals Search And Download.
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-Dong, Jungwon-Gu,
Sungnam, Kyungki-Do, Korea 462-703
TEL: +82-31-740-8137~8141 FAX: +82-31-740-8145
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
ELECTORONIC IMAGING DIV.
SAMSUNG OPTO-ELECTRONICS UK LTD.
Samsung House, 1000 Hillswood Drive
40 Seaview Drive, Secaucus NJ 07094, U.S.A
TEL : +1-201-902-0347 FAX: +1-201-902-0429
Hillswood Business Park Chertsey Surrey KT16 OPS
TEL: +44 (0)1932 455 308 FAX: +44 (0)1932 455 325
SAMSUNG TECHWIN MOSCOW OFFICE
LENNINGRADSDY PR-KT, 37A. KORP.14
RUSSIA, 125167, MOSCOW
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD .
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL: +7-095-258-9296, 9298 FAX: +7-095-258-9297
TEL : +86-22-2761-4599 FAX: +86-22-2769-7558
P/No.:6806-0586-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
|