Instruction Manual
DVD-V9090
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of fire or electric shock to persons.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of important oper-
ating and maintenance (servicing) instructions in the literature accompany-
ing the appliance.
Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of
the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that provides guidelines for proper ground-
ing and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as
close to the point of cable entry as practical.
Caution: FCC regulations state that any unauthorized changes or modifications to this equipment may void the user's
authority to operate it.
Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Attention: Pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Important : One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of
U.S. copyright laws.
Certain Canadian programs may be copyrighted and any unauthorized recording in whole or in part may be a violation
of these rights.
To prevent damage which may result in fire or electric shock hazard,
do not expose this appliance to rain or moisture.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli
fiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When
a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-2
Table of Contents
Audio Language . . . . . . . . . . . . . . . . . . . . . . . 16
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . 17
Digital Output . . . . . . . . . . . . . . . . . . . . . . . . . 17
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dynamic Compression . . . . . . . . . . . . . . . . . . 18
PCM Down Sampling . . . . . . . . . . . . . . . . . . . 19
TV Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . 19
Black Level . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Alt Video Out . . . . . . . . . . . . . . . . . . . . . . . . . 20
Parental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Safety
Important Safety Instructions . . . . . . . . . . . . .
2
ꢀ Welcome
Feature Summary . . . . . . . . . . . . . . . . . . . . .
Disc Type and Characteristics . . . . . . . . . . . .
4
4
ꢀ 1 - System Overview
Unpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Overview . . . . . . . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Display . . . . . . . . . . . . . . . . . . . .
Insert Batteries into Remote . . . . . . . . . . . . .
5
5
5
7
7
ꢀ
8 - DVD Operations
Special Playback Features . . . . . . . . . . . . . . . 22
Disc Menu Navigation . . . . . . . . . . . . . . . . . . . 22
EZ View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Title/Chapter/Time Selection . . . . . . . . . . . . . . 24
Angle View . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
A to B Repeat . . . . . . . . . . . . . . . . . . . . . . . . 26
Repeat Chapter/Title . . . . . . . . . . . . . . . . . . . . 26
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Function (DVD) . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ 2 - Getting Started
Basic Connections/Auto Setup . . . . . . . . . . .
7
ꢀ 3 - Advanced Connections
Stereo Connections . . . . . . . . . . . . . . . . . . . .
S-Video/Component Video Connections (for DVD) . . . .
Monitor TV Connections . . . . . . . . . . . . . . . . .
Connecting Other Video Equipment . . . . . . . . .
8
8
9
9
ꢀ
ꢀ
4 - DVD Sound Setup
A/V Receiver Connections . . . . . . . . . . . . . . . . 10
5 - Basic Operation
ꢀ
ꢀ
9 - VCR Playback
Deck Control Buttons . . . . . . . . . . . . . . . . . . . 10
Basic DVD Operation . . . . . . . . . . . . . . . . . . . 10
Basic VCR Operation . . . . . . . . . . . . . . . . . . . 11
Basic TV Tuner Operations . . . . . . . . . . . . . . . 11
Special VCR Playback Features . . . . . . . . . . . . 28
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
S-VHS Playback . . . . . . . . . . . . . . . . . . . . . . . 30
Variable Search System . . . . . . . . . . . . . . . . . 30
ꢀ
6 - System Setup
On-Screen Menu Navigation . . . . . . . . . . . . . . 11
Menu Language . . . . . . . . . . . . . . . . . . . . . . . 12
Manual Clock Set . . . . . . . . . . . . . . . . . . . . . . 12
Tuner Band Setting . . . . . . . . . . . . . . . . . . . . . 13
RF Output Channel . . . . . . . . . . . . . . . . . . . . . 13
Auto Channel Memory . . . . . . . . . . . . . . . . . . . 14
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . 14
Front Panel Dimmer . . . . . . . . . . . . . . . . . . . . 15
Auto Power Off . . . . . . . . . . . . . . . . . . . . . . . . 15
10 - VCR Recording
Basic Recording . . . . . . . . . . . . . . . . . . . . . . . 31
Special Recording Features . . . . . . . . . . . . . . . 31
One Touch Recording (OTR) . . . . . . . . . . . . . . 32
Record Speed . . . . . . . . . . . . . . . . . . . . . . . . 32
ꢀ11 - Timer Recording
How to Set a Timer Recording . . . . . . . . . . . . . 33
Function(VCR) . . . . . . . . . . . . . . . . . . . . . . . . 33
ꢀ
7 - DVD Setup
ꢀAppendix - Help
Disc Menu Language . . . . . . . . . . . . . . . . . . . 16
Technical Specifications . . . . . . . . . . . . . . . . . 34
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-3
Feature Summary
Disc Type and Characteristics
DVD-VCR Features
Disc Markings
• Perfect compatibility to play back DVDs,
audio CDs, SVCD, JPEG FILCS CDs, or
VHS Tapes.
• Play Region Number
~
• Enjoy a DVD movie while recording a TV
show to the VCR.
• Auto Setup instantly finds the time and runs
channel search.
• RF inputs and outputs for all kinds of TVs
available.
• Composite, S-Video, and Component Video
outputs.
• NTSC broadcast system in U.S.A, Canada,
Korea, Japan, etc.
NTSC
• Dolby Digital disc
• Stereo disc
STEREO
DIGITAL
SOUND
• Universal remote provides the full operation
on DVD-VCR.
• Digital Audio disc
• On-Screen Program
• DTS disc
(English/French/Spanish).
DVD Features
• 10-bit video digital to analog converter and
27MHz advanced digital filter.
• Playback of 96KHz/24-bit sources.
• 4 in 1 slot to support 4 types of memory
cards : memory Stick, SD Card, MMC, and
Smart Media Card.
Play Region Number
Both the DVD player and the discs are coded by
region. These regional codes must match in order for
the disc to play. If the codes do not match, the disc
will not play.
The Region Number for this player is described
on the rear panel of the player.
• Play back MP3-CDs.
VCR Features
• Hi-Fi Stereo VCR.
• Superior slow motion and stop action
(with 4 heads).
• Playback of S-VHS tapes with a better than
standard resolution.
• INTRO Scan, Zero Return, and END Search.
• 7-event/1 month timer recording.
• Time remaining counter, real time counter.
Note
* Discs which cannot be played with this
player.
• DVD-ROM
• CDI
• DVD-RAM
• CDV
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
• VCD
* Ability to play back may depend on recording
conditions.
• DVD-R
• CD-RW
• DVD+RW, -RW • CD-ROM
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-4
Disc Types (Logos) Recording Types Disc Size
DVD
Max. Playing Time
Characteristics
•
•
DVD contains excellent sound and video
due to Dolby Digital and MPEG-2 system.
Single-sided 240 min.
Double-sided 480 min.
Audio
+
12 Cm
Various screen and audio functions can
be easily selected through the on-screen
menu.
Single-sided 80 min.
Double-sided 160 min.
8 Cm
Video
•
An LP is recorded as an analog signal
with more distortion. CD is recorded as a
Digital Signal with better audio quality,
less distortion and less deterioration of
audio quality over time.
AUDIO-CD
12 Cm
8 Cm
74 min.
20 min.
Audio
* It may not be to play CD-R,CD-RW and DVD-R in all cases due to the type of disc or condition of the recording.
Unpack
When you unpack the DVD-VCR, please check the following list of items is included in the packing case.
DVD-VCR
RF Antenna Cable
User’s Guide
RCA cable for
Remote Control
1.5V “AAA” Batteries- 2EA
EP-2 Plug Converter
Audio/Video connection
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-5
Front Panel Overview
1
2
3
4
5
6
7
8
9
10 11
12
13 14 15
16 17 18
1
2
3
4
5
6
7
8
9
DVD DECK
10
FAST-FORWARD/FWD
RECORD
DVD OPEN/CLOSE
VCR DECK
VCR EJECT
POWER
11
12
13
14
15
16
17
18
FRONT PANEL DISPLAY
CHANNEL
/
DVD-VCR SELECT
PROGRESSIVE
EZ VIEW
REWIND/REV
STOP
LINE IN 2 COMPOSITE VIDEO JACK
LINE IN 2 LEFT AUDIO JACK
PLAY/PAUSE
LINE IN 2 RIGHT AUDIO JACK
Rear Panel
1
2
3
4
5
6
7
8
1
2
3
4
S-VIDEO OUT
5
6
7
8
LINE IN 1
DIGITAL AUDIO OUT(COAXIAL)
COMPONENT VIDEO OUT
AUDIO LINE OUT TO TV
LINE OUT TO TV (COMPOSITE)
RF ANTENNA INPUT
RF OUT TO TV (RF THROUGH ONLY)
(S-VIDEO OR COMPONENT)
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-6
Front Panel Display
1
2
3
LINE INPUT
4
5
1
2
When the light is on, DVD is operating.
The time, counter position, time remaining or
current deck status is indicated.
VCR is activated.
2
Connect your DVD-VCR to a TV
RF Connection
3
4
5
Using the RF antenna cable , connect the OUT
①
DVD or CD media is loaded.
VHS videotape is loaded.
jack (TO TV) on the rear panel of your DVD-VCR to
your TV’s Antenna Input.
Line Connection
Using an RCA-type audio/video cable① (red, white,
yellow), connect the LINE OUT jacks on the rear
panel of your DVD-VCR to your TV's Line In jacks.
Use the three cables as follows: red for right audio,
white for left audio, and yellow for video.
Insert Batteries into Remote
Note: If your TV is equipped with RCA jacks, it is
better to use the Line Connection method.
3
Plug In
Your DVD-VCR's power should be plugged into a
standard 120V/60Hz wall outlet. Avoid pressing any
buttons on the remote control or on the unit during
an Auto Setup. While your DVD-VCR is running an
Auto Setup, “AUTO” will blink. When Auto Setup is
complete, the current time will be displayed on the
front panel displayed. In case Auto Clock set fails to
locate a channel to set the clock, you should set
the clock manually. See page 11.
• Remove the battery cover on the remote
• Insert two 1.5V “AAA” batteries as shown,
making sure of the correct polarities(+/-)
• Slide the cover back onto remote.
Basic Connections/Auto Setup
3
You will need to connect the DVD-VCR to a TV and run
Auto Setup. The Auto Setup will automatically search for
channels and then set your DVD-VCR's internal clock.
NOTES:
• See page 7 for Advanced Connections.
4
Turn On your DVD-VCR
Turn on the power by pressing the POWER button
on the remote control or on the front panel of the
unit.
• Standard RF or Line connection between your TV
and DVD-VCR are required to run DVD-VCR
setup menu, even if you connect S-Video or
Component Video Output for a better picture
quality.
5
6
Turn On your TV
Turn on the TV by pressing the POWER button on
the TV remote control.
1
Connect the RF Antenna Cable
① to your DVD-VCR
Connect an external indoor/outdoor antenna or wall
outlet antenna cable to the Ant-In jack on the rear
panel.
Set the TV to Line
Set your TV to its Line Input.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-7
S-Video/Component Video
Connections (for DVD)
Stereo Connections
You can connect your DVD-VCR to your home stereo
system or stereo TV and enjoy stereo sound when
watching a movie or TV.
Use the S-Video or Component Video connection
method only for the DVD player. The tuner and VCR
can still be viewed through the RF or line inputs.
To activate your alternative (S-Video or Component)
video selection, follow the “Alt Video Out” instructions
on page 20. Keep in mind that you can choose either
S-Video or Component only, but not both. A superior
video quality can be obtained when watching a DVD
on your DVD-VCR if your TV is equipped with S-Video
or Component Video inputs.
1
Connect DVD-VCR to Stereo
Using RCA cables, connect the Line Out Left and
Right Audio jacks on the rear panel of the DVD-VCR
to the Auxiliary Inputs on your stereo receiver.
Connect the Video Output also in case you are using
a stereo TV.
1
Connect S-Video Out to TV
Using an S-Video cable, connect the S-VIDEO OUT
on the rear panel of your DVD-VCR to the S-Video
Input on your TV.
2
3
Set Stereo to Auxiliary Mode
Set your stereo receiver or TV to either “Aux” or
“Tape” regardless of which line input you are using for
your particular device.
To S-Video Input on Your TV
2
Connect Component Video Out to TV
Using a component video cable, connect the
COMPONENT VIDEO OUT (Y, Pb, Pr) on the rear
panel of your DVD-VCR to the Component Video
Input on your TV. .
Play a Tape
Insert a DVD or Hi-Fi stereo videotape into your
system. Be sure to adjust the volume on your stereo
receiver or TV. Audio will be heard through your
stereo speakers
• If there is no stereo sound even after you have
inserted a Hi-Fi stereo videotape, press the AUDIO
button until “Hi-Fi” appears on the on-screen display.
To Component Video Input
on Your TV
3
Connect Audio Out (DVD only)
Using RCA audio cables, connect the LEFT/RIGHT
Line Out jacks on the rear panel of your DVD-VCR
to the LEFT/RIGHT Audio Line In jacks on your TV.
• When connecting your DVD-VCR to a TV with the
S-Video or Component Video Output, make sure
that you use these Line Out jacks.
• To activate your connection, see “Alt Video Out”
on page 20.
To Left/Right Audio Inputs
on Your TV
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-8
Connecting Other Video
Equipment
Monitor TV Connections
Monitor-style televisions offer improved sound and
picture over regular televisions because they receive
the audio and video signals directly from the DVD-VCR
through the line inputs.
You can connect a wide variety of audio/video
equipment to your DVD-VCR, including:
• An additional VCR
• Laser Disc Player
• DVD Player
NOTE: A monitor television is not the same as a
computer monitor.
• Camcorder
• Satellite Receiver
• Video Game
1
2
3
Connect VCR to Monitor TV
Since all of these devices use essentially the same
connections, they will be described together.
Connect RCA cables from the Audio/Video Line Out
jacks on the rear panel of the DVD-VCR to the
Audio/Video Line Inputs of your monitor TV.
1
Connect Device to DVD-VCR
Connect RCA cables from the Audio and Video Line
Outputs of your external device to the Audio and
Video Line Inputs on the front or rear panel of the
DVD-VCR.
To Monitor TV Audio/Video Inputs
Set TV to Auxiliary Mode
Set your monitor TV to “Aux,” “Video,” or “Line.” Refer
to your monitor television owner’s manual for the
correct setting.
Audio/Video Outputs of
External Device
2
3
Watch Device
Play your external device, then press the INPUT
SEL. button until the playback from Line1 (rear panel
inputs) or Line2 (front panel inputs) appears on your
TV screen.
Record Device
First, play your external device. Next, press the
INPUT SEL. button until the playback from Line1
(rear panel inputs) or Line2 (front panel inputs)
appears on your TV screen. Then press Record on
the Front panel and Remote Control.
Connection is Complete
4
Timer Record From Device
Select Line1 (L1) or Line2 (L2) as your record source
in the Timer Record menu. All other Timer Record
settings should be set in the usual manner.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-9
A/V Receiver Connections
Deck Control Buttons
To take full advantage of the movie theater experience
that DVD offers, you may want to connect your DVD-
VCR to a complete Surround Sound system, including
an A/V Receiver and six Surround Sound speakers.
The DVD-VCR uses one set of controls to operate both
decks. The following buttons are helpful in successfully
controlling each deck.
1
POWER Button
Before You Begin...
Press the POWER button on the remote control or
front panel to turn on the DVD-VCR.
•
If your A/V receiver is equipped with a Dolby
Digital Decoder, you have the option to bypass the
DVD-VCR’s built-in Dolby Digital Decoder. Use the
Digital Audio Out connection below.
2
DVD Button
Press the DVD button on the remote control or front
panel when you want to control the DVD deck.
• The DVD indicator will light on the Front Panel
Display to show that the DVD deck is selected.
3
4
VCR Button
Press the VCR button on the remote control or front
panel when you want to control the VCR deck.
• The VCR indicator will light on the Front Panel
Display to show that the VHS deck is selected.
To Digital Audio Input of an A/V
INPUT SEL. Button
Receiver with a Dolby Digital Decoder
Press the INPUT SEL. button repeatedly to cycle
through all of your input sources, including the
Tuner(Ch##), Line 1 (rear AV input), and Line 2
(front AV input).
• Input selection is only available when the VCR
deck is selected.
1
Digital Audio Out
Connect a digital coaxial cable from the Digital
Audio Out jack on the rear panel of the DVD-VCR
to the corresponding Digital Audio Input jack on
your A/V Receiver:
• Coaxial
• Use whichever connection is available on your
A/V Receiver.
Basic DVD Operation
Follow the instructions below to playback a DVD.
1
Open the Disc Tray
Press the OPEN/CLOSE button on your remote
control or on the front panel of the unit to turn on
the power and open the disc tray.
2
3
Insert a Disc
Put a disc in the center of the tray, with the label-
printed side facing up.
Close the Disc Tray
Press the OPEN/CLOSE button on your remote
control or on the front panel of the unit to close the
disc tray.
4
5
Play a DVD
Press the ❿ll(PLAY/PAUSE) button on your remote
control or on the front panel of the unit.
• Most discs will start to playback as soon as the
tray closes.
• If a DVD has a MENU, the menu may pop up on
TV screen.
Additional DVD Options
• See pages 16 ~ 21 for advanced DVD Setup options.
• See pages 22 ~ 28 for special DVD Playback
features.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-10
Basic VCR Operation
Basic TV Tuner Operations
To play a standard VHS videotape, just insert it into the
VCR deck and press the PLAY button. You can turn on
the Auto Play to enable the VCR deck to play
automatically when you insert a videotape that is
missing the Record Safety Tab. See page 29.
When watching TV using the DVD-VCR's built-in TV
tuner, use the buttons below.
1
TV/VCR
Press this button to switch between your TV’s tuner
and the VCR’s internal tuner.
• You don’t need to press the TV/VCR button in vcr
mode.
2
3
4
Channel UP/DOWN
Use these buttons to move to the previous or the
next channel.
0-9 Buttons
Use these buttons to select the desired channel
directly.
1
2
Insert VHS Tape
Insert a standard VHS videotape into the VCR
deck.
• When a videotape is inserted, power will turn on
automatically.
100 + Buttons
Press this button tune to channels 100 and above.
First, press the 100+ button, then use the numeric
buttons(0-9) to enter the remaining digits of the
channel numeber desired.
• This button is activated only in Cable TV Mode.
Play Tape
Press the ❿ll(PLAY/PAUSE) button on the remote
control or on the front panel of the unit. The
videotape will begin to play automatically if it is
missing the Record Safety Tab and Auto Play is
turned on. See page 28.
5
INFO. Button
Press this button to display the current channel.
• This also works in DVD and VCR mode.
On-Screen Menu Navigation
3
4
Stop Playback
Press the (STOP) button on the remote control or
on the front panel of the unit.
①
The on-screen menus allow you to enable or disable
various functions on your DVD-VCR. Use the following
buttons to open and navigate through the on-screen
menus.
Additional VCR Options
• See pages 28~29 for special VCR Playback
features.
• See pages 31~32 for VCR Recording features.
• See page 33 for Timer Recording features.
Language
:
English
Front Display
:
:
Auto
Off
Auto Power Off
1
2
MENU Button
Press this button while the DVD is in Stop or Play
mode to open the on-screen MAIN MENU.
UP/DOWN and LEFT/RIGHT
Use these buttons to move the selection bar
UP/DOWN and LEFT/RIGHT to cycle through the
menu options.
3
4
ENTER Button
Press this button to confirm any new settings.
RETURN Button
Press this button to return to the last MENU screen
displayed or to exit the on-screen MENU all together.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-11
Menu Language
Manual Clock Set
To change the on-screen MENU language to English,
French or Spanish, follow these steps.
If Auto Setup fails to set the DVD-VCR’s internal clock
by locating a local TV station, follow these steps to set
the date and time manually.
1
Open “MENU”
NOTE: For accurate Timer Recording, your DVD-VCR's
internal clock must be set correctly.
Press the MENU button while the DVD is in Stop or
Play mode.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop or
Play mode.
2
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Language
:
English
Select “Clock”
Use the UP/DOWN buttons to highlight “Clock ”
then press the ENTER button.
Front Display
:
:
Auto
Off
Auto Power Off
Language
:
English
Front Display
:
:
Auto
Off
Auto Power Off
3
Select “Language”
Use the UP/DOWN buttons to highlight “Language”
then press the ENTER button.
4
Select “Manual Clock”
Move the highlight to “Manual Clock”, then press
the ENTER button.
• The Clock Set/Adjust menu will change as shown.
4
Set menu Language
Place the selection bar next to your desired
Language, then press the ENTER button.
5
Set the Clock
Use the LEFT/RIGHT buttons to select each of the
following options, then use the UP/DOWN buttons
to set each option:
Language
:
English
• Hour – Set the hour
• Month – Set the month.
• Minute – Set the minute. • Day – Set the day.
Front Display
:
:
Auto
Off
Auto Power Off
• Year – Set the year
Manual Clock
2004 THU
6
Confirm Settings
Press the RETURN button to confirm your clock
settings and to return to the Clock Set/Adjust.
• Press the RETURN button three times to exit the
menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-12
Tuner Band Setting
RF Output Channel
1
2
3
Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
This feature allows you to manually set the DVD-VCR’s
tuner band to Antenna or Cable, whichever you
connected to the Antenna In jack during initial setup.
•
Use this setting only if Auto Setup detected the
incorrect tuner band, i.e. channels are coming in on
the wrong channel numbers.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “Setup” then press ENTER to select.
1
Open “MENU”
Select “Channel”
Using the UP/DOWN buttons, move the selection
bar to “Channel,” then press ENTER to select.
With the DVD in Stop or Play mode, press the
MENU button.
2
3
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Language
:
English
Select “Channel”
Using the UP/DOWN buttons, move the selection
bar to “Channel”, then press ENTER to select.
Front Display
:
:
Auto
Off
Auto Power Off
Language
:
English
Front Display
:
:
Auto
Off
4
Select “RF Output CH”
Auto Power Off
Move the selection bar to “RF Output CH”, then
press right to change.
Ant./Cable
:
:
Antenna
4CH
3CH
4CH
4
Select “Ant./Cable”
RF Output CH
Auto Channel Memory
Move the selection arrow to “Ant./Cable” then press
RIGHT button to select from the following options:
• Antenna - Indicates that the DVD-VCR is
connected to an indoor or outdoor VHF/UHF
antenna.
Channel Add/Delete
• Cable TV - Indicates that the DVD-VCR is
connected to Cable TV.
5
6
Change “RF Output CH”
A message will appear on your TV.
Then press ENTER to change.
Cable TV
Antenna
Ant./Cable
:
:
Antenna
3CH
RF Output CH
Change “TV Channel”
Auto Channel Memory
Channel Add/Delete
A message will appear on your TV. When the
message disappears, change your TV to channel 3
or 4 to match the RF output channel of the player.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-13
Auto Channel Memory
Channel Add/Delete
Auto Channel Memory will automatically seek and store
all active channels in your area.
Use this feature if Auto Channel Search missed a
channel that you would like to add, delete a channel
you wish to remove.
1
2
3
Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
1
2
3
Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Select “Channel”
Select “Channel”
Using the UP/DOWN buttons, move the selection
bar to “Channel”, then press ENTER to select.
Using the UP/DOWN buttons, move the selection
bar to “Channel”, then press ENTER to select.
Language
:
English
Language
:
English
Front Display
:
:
Auto
Off
Front Display
:
:
Auto
Off
Auto Power Off
Auto Power Off
4
Select “Channel Add/Delete”
Move the selection bar to “Channel Add/Delete,”
then press ENTER to select.
4
Run “Auto channel memory”
Move the selection arrow to “Auto Channel
Memory,” then press ENTER to select.
• The DVD-VCR will automatically search for all
available channels in the selected Tuner Band.
This procedure may take a few minutes to
complete.
Ant./Cable
:
:
Antenna
3CH
RF Output CH
Auto Channel Memory
Channel Add/Delete
• When finished, the lowest channel found will be
displayed.
Ant./Cable
:
:
Antenna
3CH
5
6
Select Channel to Add/Delete
Use the CH buttons to tune in the channel
number you wish to add or delete.
RF Output CH
Auto Channel Memory
ꢀ
/
❷
Channel Add/Delete
Select “Channel Add/Delete”
Press RIGHT button to add or press left button to
delete the channel from your channel list.
• Repeat steps 4 and 5 to add or delete additional
channels.
CHANNEL ADD/DELETE
Select channel :
[02]
and press
press
[
❿
]
to ADD
to DELETE
[
➛
]
ꢀ❷
RETURN
CH
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-14
Auto Power Off
Front Panel Dimmer
1
2
Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
You can set the Front Panel Display to be bright all the
time, dim all the time, dim during power off.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
1
2
Open “ MENU”
With the DVD in Stop or Play mode, press the
MENU button.
Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
Language
:
English
Front Display
:
:
Auto
Off
Auto Power Off
Language
:
English
Front Display
:
:
Auto
Off
Auto Power Off
3
Set “Auto Power Off”
Move the selection bar to “Auto Power Off”, then
press RIGHT button to select from following options:
• Off – Auto power off is disabled.
• 1Hr – DVD-VCR will auto shut off 1 hour after the
last button is pressed.
• 2Hr – DVD-VCR will auto shut off 2 hours after
the last button is pressed.
3
Set “Front Display”
Move the selection bar to “Front Display,” then
press RIGHT button to select from the following
options:
• Auto – Front Panel Display will dim automatically
during power off.
• Bright – Front Panel Display will be bright all the
time.
• Dim – Front Panel Display will be dim all the time.
Language
:
English
Off
1Hr
2Hr
Front Display
:
:
Auto
Off
Auto Power Off
Language
:
English
Auto
Bright
Dim
Front Display
:
:
Auto
Off
Auto Power Off
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-15
Disc Menu Language
Audio Language
To set the Disc Menu Language to your preferred
language, follow these steps. If your preferred language
is available on a DVD, your Disc Menu Language will
automatically be set to the language you choose.
To set the Audio Language to your preferred language,
follow these steps. If your preferred language is
available on a DVD, your Audio Language will
automatically be set to the language you choose.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”, then
press the ENTER button.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD” then
press the ENTER button.
Select “Language”
Select “Language”
Move the selection bar to “Language” then press
ENTER to select.
Move the selection bar to “Language” then press
ENTER to select.
4
Select “Disc Menu”
Highlight “Disc Menu”, then press the ENTER
button.
4
Select “Audio”
Highlight “Audio,” then press the ENTER button.
5
Set “Disc Menu Language” Preference
Highlight your preferred language for disc menus,
then press the ENTER button.
5
Set “Audio Language” Preference
Highlight your preferred language for audio
soundtracks, then press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-16
Subtitle Language
Digital Output
To set the Subtitle Language to your preferred language,
follow these steps. If your preferred language is
available on a DVD, your Subtitle Language will
automatically be set to the language you choose.
If your A/V receiver is equipped with a Dolby Digital
decoder, your DVD-VCR can output Dolby Digital 5.1
sound, but you MUST enable this feature in the menu
system to prevent damage to your speakers.
NOTE: Select “Bitstream” ONLY if you have connected
a Dolby Digital-equipped A/V receiver to the
Digital Output (coaxial) on the DVD-VCR rear
panel.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”
then press the ENTER button.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “Language”
Move the selection bar to “Language” then press
ENTER to select.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”
then press the ENTER button.
Select “Audio”
Highlight “Audio”, then press the ENTER button.
4
Select “Subtitle”
Highlight “Subtitle”, then press the ENTER button.
4
Set “Digital Output”
Highlight “Digital Output” then press the RIGHT
button to select one of the following options:
• PCM –
To use your DVD/TV with an A/V
receiver without a Dolby Digital
decoder.
• Bitstream –To use your DVD/TV with an A/V
receiver with a Dolby Digital decoder.
5
Set “Subtitle Language” Preference
Highlight your preferred language for subtitles, then
press the ENTER button.
PCM
Bitstream
PCM Down Sampling
:
On
Subtitle Language
Automatic
Subtitle
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-17
DTS
Dynamic Compression
If your A/V receiver is equipped with a DTS decoder,
your DVD-VCR can output DTS digital sound, but you
MUST enable this feature in the menu system.
Dynamic Compression restrains the dynamic range of
sounds, i.e. the difference between the loud and quiet
passages of a DVD audio track.
NOTE: Select “On” ONLY if you have connected a
DTS-equipped A/V receiver to the Digital audio
Out (coaxial) on the DVD-VCR rear panel.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”
then press the ENTER button.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”
then press the ENTER button.
Select “Audio”
Highlight “Audio”, then press the ENTER button.
Select “Audio”
Highlight “Audio”, then press the ENTER button.
4
Set “Dynamic Compression”
Highlight “Dynamic Compression”, then press the
RIGHT button to select one of the following options:
• On – This will compress the total dynamic range
of the DVD audio, making quiet passages
in the audio signal louder and loud
passages softer.
4
Set “DTS”
Highlight “DTS” then press the RIGHT button to
select one of the following options:
• Off – To use your DVD/TV with an A/V receiver
NOT equipped with a DTS decoder.
• On – To use your DVD/TV with an A/V receiver
equipped with a DTS decoder
• Off – This will preserve the original dynamic
range.
On
On
Off
On
Off
On
PCM Down Sampling
:
Ofnf
PCM Down Sampling
:
On
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-18
PCM Down Sampling
TV Aspect Ratio
If your amplifier is not capable of reproducing a 96kHz
signal, PCM downsampling should be set to on.
Set the aspect ratio (length x width) of your TV screen
so the DVD player will display movies at the
appropriate size for your television. Choose from
standard, letterbox, or widescreen format.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD ”
then press the ENTER button.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD”
then press the ENTER button.
Select “Audio”
Highlight “Audio”, then press the ENTER button.
Select “Display”
Highlight “Display”, then press the ENTER button.
4
Set “TV Aspect”
Highlight “TV Aspect” then press the RIGHT button
to select one of the following options:
• Widescreen - This method allows you to view the
full 16:9 picture on a widescreen television.
• Letterbox - This method displays the full width of
the widescreen movie on a standard 4:3
television. As a result, black bars will appear at
the top and bottom of the screen.
4
Set “PCM Down Sampling”
Highlight “PCM Down Sampling”, then press the
RIGHT button to select one of the following options:
• On – When a 96K audio disc is played, 96K will
be downsampled to 48K and outputted.
• Off – When a 96K disc is played, 96K will be
outputted.
• Pan-Scan - The familiar way of watching DVD and
VHS movies, this method selectively crops (by
panning and scanning to keep the most important
part of the picture visible) wide screen movies to
fit a standard 4:3 television screen.
On
Off
PCM Down Sampling
:
On
Display Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-19
Alt Video Out
Black Level
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
The Black Level feature adjusts the reference level of
black in the video signal to one of two choices:
• Off - Standard NTSC black level. Yields
consistent contrast through all sources.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD,”
then press the ENTER button.
• On - Enhanced black level, for increased contrast
during DVD playback.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “Display”
Highlight “Display”, then press the ENTER button.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD ”
then press the ENTER button.
Select “Display”
Highlight “Display”, then press the ENTER button.
4
Set “Alt Video Out”
Highlight “Alt Video Out,” then press the RIGHT
button to select one of the following options:
• S-Video - Select this if you are using the S-Video
OUT jack on the rear panel to connect to a TV.
• Component - Select this if you are using the
COMPONENT VIDEO OUT jacks on the rear
panel to connect to a Progressive(480p) or
Interlaced (480i) TV.
4
Set “Black Level”
Highlight “Black Level,” then press the RIGHT
button to select one of the following options:
• On – This will enhance the Black Level for
increased brightness/contrast when
viewing DVDs.
• See your TV owner’s manual to determine what
type of TV you have.
- Interlace : Interlaced Scan mode will work.
- Progressive : Progressive Scan mode will work,
and Video and S-Video will not work.
• Press the PROGRESSIVE button on the front
panel in stop mode if you have a Progressive
scan TV only. Otherwise, the picture will be
disturbed.
• Off – This is the Standard NTSC reference Black
Level for consistent brightness/contrast
across all sources.
Display Setup
On
Off
On
Display Setup
On
Alt Video Out
The “Alt Video Out” option must be set in the on-screen
menu if you have connected your DVD-VCR to a TV using
the S-VIDEO OUT or COMPONENT VIDEO OUT jacks.
•
Use the S-Video or Component Video connection
method only for the DVD player. The tuner and VCR
can still be viewed through the RF or line outputs.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-20
Parental
5
Enter Password
Rating Control is a password protected system that
allows you to block playback of DVDs based on their
content. The system uses an eight level rating system.
Use the numeric buttons (0-9) on the remote
control to enter the 4-digit password.
• Write your password down, and keep it in a safe
place in case you need to change your settings
later.
•
If you try to play a DVD that exceeds the selected
rating, an error message will appear.
•
Not all discs are rated.
1
2
3
Open “MENU”
Press the MENU button while the DVD is in Stop
mode.
Select “DVD”
Use the UP/DOWN buttons to highlight “DVD ”
then press the ENTER button.
0~9
Select “Parental”
Highlight “Parental”, then press the ENTER button.
6
Select “Rating Level”
Move the selection bar to “Rating Level,” then
press ENTER to select.
Yes
7
Change Rating Level
4
Select “Use Password”
Use the UP/DOWN buttons to select one of the
following ratings:
Press the RIGHT button to select one of the
following options:
• No - No password is necessary to view a DVD or
to change the Rating Level. No additional
settings are necessary.
• Yes - A password is necessary to view a DVD and
to view the Rating Level. The menu will
change as shown.
• Level 8 Adult
• Level 7
• Level 6
• Level 4
• Level 3
• Level 2
• Level 1 Kids Safe
• Level 5
All ratings above the level you select will also be
blocked, e.g., if you select Level 6, then Levels 7
and 8 will also be blocked.
NOTES:
• The first time “Use Password” is set to “No,”
you will be prompted to enter a new password.
• If the “Enter Password” screen appears, then
“Use Password” has already been set to
“Yes.” Please skip to Step 6.
Press Enter to confirm your selection.
• If you forgot your password, press power on from
a cold start with no disc in the unit. Press the REW
and F.F buttons simultaneously on the front panel
for 5 seconds. The “Reset Ok” message will appear.
Press the POWER button.
• There is no default password.
No
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-21
Special Playback Features
Stop/Resume
• Press the STOP button once to stop playback. To
During DVD/CD playback you can select from the
following special playback options. To resume normal
playback, press the ❿ll(PLAY/PAUSE) button.
resume the DVD/CD from the point where the
disc stopped, press the ❿ll(PLAY/PAUSE)
button.
1
2
3
PAUSE
• Press the
ꢀ(STOP) button twice to completely
Press the ❿ll(PLAY/PAUSE) button on the remote
control during playback.
• The picture will pause and the audio will mute.
• To resume playback, press the ❿ll(PLAY/PAUSE)
button.
stop playback. The next time you press ❿ll
(PLAY/PAUSE), the disc will start over from the
beginning.
• If the player is left in Pause mode for 5 minutes,
it will stop automatically.
Frame Advance (Step)
While in PAUSE mode, press the F.ADV/SKIP button
on the remote control to advance one frame at a time.
• Audio is muted during Frame Advance mode.
• Press ❿ll(PLAY/PAUSE) to resume normal
playback.
Disc Menu Navigation
NOTE: Frame Advance operates only in the
forward direction.
Many DVDs feature their own menu systems, where
you can select Titles, Chapters, Audio Tracks, Subtitles,
and special disc features, such as movie trailers, and
information on the cast. Use these buttons to make
selections in the Disc menus.
Skip Forward/Back
While a CD or DVD disc is in Play mode, press the
SKIP FORWARD/BACK (❿❿
l
/
l➛➛ ) buttons on the
remote control or front panel to jump forward and
backward through disc chapters/tracks.
• Skip Forward will jump to the next chapter/track.
• Skip Back will jump to the beginning of the current
chapter/track.
1
2
DISC Menu
Press to access the DVD’s Disc menu, if applicable.
Press UP/DOWN and LEFT/RIGHT to navigate
through DVD’s Disc menu options.
• Press UP/DOWN and LEFT/RIGHT to highlight
menu choices.
• Press Skip Back again to jump to the beginning of
the previous chapter/track.
Search Forward/Back
While a disc is in Play mode, press and hold the
3
ENTER Button
Press to make your selections in the Disc menu.
FORWARD/BACK (❿❿ ➛➛ ) buttons on the remote
/
control or front panel to visually search
forward/backward at 2X - 8X - 32X - 128X speed.
Press ❿ll(PLAY/PAUSE) button to resume normal
speed.
NOTE: CD search speed - 2X, 4X, 8X
2
4
Slow Motion
During playback, press the❿ll(PLAY/PAUSE)button
to pause the image. Press and hold the Search
FORWARD (❿❿) to play in slow motion at variable
speeds.
3
1
• Press and hold the FORWARD(❿❿) button on
the remote and front panel to increase the speed
from normal playback to 1/8, 1/4 or 1/2 speed.
• Audio is muted during slow motion playback.
• Press the ❿ll(PLAY/PAUSE) button to resume
normal playback.
NOTE: • Slow function is not available for CD.
• Slow motion operates only in the forward
direction
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-22
EZ View
1
Press the EZ VIEW button on the front panel.
• The screen size changes when the button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on the screen setting in the initial setup
menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the initial setup .(See the page 18)
• Screen Fit
The top and bottom of the screen are cut off and
the full screen appears. The picture will look
vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Vertical Fit
2
If you are using a 16:9 TV
- For 16:9 aspect ratio discs
• Wide Screen
Displays the content of the DVD title in 16:9
aspect ratio.
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the screen
in order to prevent the picture from looking
horizontally stretched.
3
If you are using a 4:3 TV
• Screen Fit
- For 16:9 aspect ratio discs
The top and bottom of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the
black bars at the top and bottom of the screen
will disappear. The picture will look vertically
stretched. (Depending on the type of disc, the
black bars may not disappear completely.)
• 4:3 Letter Box
Displays the content of the DVD title in 16:9
aspect ratio.
The black bars will appear at the top and bottom
of the screen.
• Zoom Fit
• 4:3 Pan Scan
The left and right of the screen are cut off and
displays the central portion of the 16:9 screen.
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Screen Fit
The top and bottom of the screen are cut off and
the full screen appears. The picture will look
vertically stretched.
• Zoom Fit
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the screen
in order to prevent the picture from looking
horizontally stretched.
- For 4:3 aspect ratio discs
• Normal Screen
Displays the content of the DVD title in 4:3 aspect
ratio.
• Screen Fit
The top and bottom of the screen are cut off and
the full screen appears. The picture would look
vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
- For 4:3 aspect ratio discs
• Normal Wide
Displays the content of the DVD title in 16:9
aspect ratio.
①
This function may behave differently depending on
the type of disc.
The picture will look horizontally stretched.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-23
Title/Chapter/Time Selection
①
To make the screen disappear, press the INFO
button again.
To view the current Title, Chapter/Track, and counter
position, press the INFO. button during DVD playback.
The Information screen can also be used to quickly
choose a title, chapter/track, or playing time.
To access the desired title when there is more than
Title
one in the disc. For example, if there is more than
one movie on a DVD, each movie will be identified.
1
2
View the Display
During DVD/CD playback, press the INFO. button
on the remote control.
Most DVD discs are recorded in chapters so that
you can quickly find a specific passage.
Chapter
Select title
Allows playback of the film from a desired time.
You must enter the starting time as a reference.
Time
Audio
Use the UP/DOWN and LEFT/RIGHT buttons to
select Title, then press the numeric buttons or
LEFT/RIGHT buttons to change among all
available titles on the disc.
Refers to the language of the film soundtrack. In the
example, the soundtrack is played in English 5.1CH.
A DVD disc can have up to eight different
soundtracks.
Refers to the subtitle languages available in the
disc. You will be able to choose the subtitles
language or, if you prefer, turn them off from the
screen. A DVD disc can have up to 32 different
subtitles.
Subtitle
ENG
ENG
MOVE
3
Select Chapter or Track
Use the UP/DOWN and LEFT/RIGHT buttons to
select Chapter or Track, then press the ENTER
button to change among all available
Chapters/Tracks on the disc.
ENG
ENG
MOVE
4
Select Counter Position
Use the UP/DOWN button to select the counter
position indicator, then use the numeric buttons
(0-9) to enter the desired counter position in the
format H:MM:SS (H = Hours, M = Minutes, S =
Seconds).
Then press the ENTER button to enter the desired
counter position.
ENG
ENG
0~9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-24
Subtitle
Angle View
Some DVDs provide subtitles in one or more languages.
You can use the SUBTITLE button to quickly view and
change settings.
Some DVD Movies provide you with various
camera angle views on the same scene while
they are playing. To activate the feature
press the ANGLE Button.
1
2
Open Subtitle Menu
During playback, press the SUBTITLE button.
1
2
3
Check for the Angle Icon
Press the Angle button, you’ll see the Angle Icon
when watching a DVD with multi Angles available.
Set Subtitle Language
Use the LEFT/RIGHT buttons to select from the
available subtitle languages.
• Subtitle languages are represented by
abbreviations.
View Angle Menu Options
When the Angle Icon comes up on the screen press
the ANGLE button to see the Angle menu.
Select an Angle option
3
Activate Subtitles
Press the UP/DOWN buttons to select a camera
angle you wish to see.
Use the UP/DOWN buttons to turn On or Off
subtitles.
• The default is "On".
• To make the screen disappear, press the
SUBTITLE button again.
ENG
On
ENG
Off
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-25
A to B Repeat
Repeat Chapter/Title
A to B Repeat feature enables you to repeat the
designated section on a DVD or CD. To activate, mark
where to start(A) and where to end(B) of the section
you want to watch.
You can repeat a single chapter or a complete title.
1
2
Open Repeat Menu
Press the REPEAT button while in Play mode to
open the Repeat menu.
1
Select A-B Repeat Function
• The current Repeat mode will be highlighted.
Press the REPEAT button while in Play mode, then
use the Left/Right buttons to select A-B Repeat.
• When you select A-B Repeat, “A-” will be
highlighted.
Select “Chapter / Track”
Use the LEFT/RIGHT buttons to select “Chapter/
Track”.
• When you select Chapter/Track Repeat,
“Chapter/Track” will be highlighted.
NOTE: The menu will display “Track” in place of
“Chapter” if you are playing a CD.
DVD
DVD
Chapter Title A - B
Off
Chapter Title A - B
Off
CD
CD
Track Disc A - B
Off
Track Disc A - B
Off
3
4
Repeat Chapter/Track
Press the ENTER button to repeat the current
chapter or Track.
2
Mark the Starting Point
Press the ENTER button at the beginning of the
segment you want to repeat (Point A).
• Once you select Point “A”, “B” will be highlighted.
Select “Title/Disc”
Use the LEFT/RIGHT buttons to select “Title/Disc”.
• When you select Title/Disc Repeat, “Title/Disc” will
be highlighted.
NOTE: The minimum A -B Repeat time is 5 seconds.
3
Mark the Ending Point
Press the ENTER button again at the end of the
segment you want to repeat (Point B).
• The segment will begin repeating in a continuous
loop.
5
Repeat Title/Disc
Press the ENTER button to repeat the Title/Disc.
4
Cancel A-B Repeat
Press the REPEAT button to open the Repeat
Menu, use the LEFT/RIGHT buttons to highlight
“Off,” then press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-26
Audio
Bookmarks
Multiple audio language setup options, such as Dolby
Digital 5.1, Dolby Pro Logic, or LPCM 2 Channel audio,
are available on some DVDs. You can use the AUDIO
button to quickly view and select the options available
on a disc.
Up to three Bookmarks can be inserted for a given
DVD, allowing you to quickly jump to your favorite
scene or song.
1
2
3
Open Bookmark Menu
During playback, press the MARK button on the
remote control.
1
2
Open the Audio Menu
During playback, press the AUDIO button on the
remote control.
The “MARK” header will be displayed on the screen.
Select Bookmark Placeholder
Use the LEFT/RIGHT buttons to move to one of the
three bookmark placeholders (- - -).
Select DVD Audio Track
Use the LEFT/RIGHT buttons to select the desired
audio language setup on the DVD.
• Languages are represented by abbreviations, e.g.
“ENG” for “English.”
• The selected placeholder will be highlighted.
Set the Bookmark
Keep on playing the DVD up to the scene you want
to bookmark, then press the ENTER button. The
placeholder (-) will change to a number (1, 2 or 3).
• You may continue to set up to three bookmarks.
• Press the MARK button when complete.
• Depending on the disc, the bookmark function
may not work.
DVD
DOLBY DIGITAL 5.1CH
ENG
4
Play Bookmark
• During playback, press the MARK button on the
remote control.
• Use the LEFT/RIGHT buttons to move to a
previously set bookmark.
• Press the ❿ll(PLAY/PAUSE) button to play the
bookmark.
• Press the CLEAR button to cancel the bookmark.
• Press the MARK button again to exit the
Bookmark menu.
CD
Stereo
–
–
–
CLEAR
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-27
Special VCR Playback Features
Function (DVD)
While a videotape is playing, you can enjoy a variety of
special playback features, including Still, Frame
Advance, Skip, Repeat, and more. Press the Play button
again to resume normal playback.
Use this feature to check your DVD.
1
2
3
Open “MENU”
With the DVD in Play mode, press the MENU
button.
1
2
3
Pause
Select “FUNCTION”
Use the UP/DOWN buttons to highlight
“FUNCTION” then press the ENTER button.
In Play mode, press ❿ll(PLAY/PAUSE) to still a
single frame.
Frame Advance
In the pause mode, press F.ADV/SKIP to advance
to the next frame.
Select “DVD Function”
Using the UP/DOWN buttons to highlight “DVD
Function” then press ENTER to select.
Fps/Review
In Play mode, press FORWARD (❿❿) or
REWIND (➛➛ ) to Cue/Review at two speeds:
• Picture Search — Press and release to advance
the tape forward or backward at 5 times normal
speed.
• Jet Search — Press and hold to advance the tape
forward or backward at 7 times normal speed.
4
5
Skip
In Play mode, press F.ADV/SKIP to cue ahead
exactly 30 seconds. Press F.ADV/SKIP repeatedly
up to 4 times to cue ahead 2 minutes.
4
Select “Title Menu”
Highlight “Title Menu”, then press the ENTER
button.
Repeat
- Disc Menu
• In Play mode, press Repeat to review the last
5 seconds of tape (SP mode).
• In Play mode, press Repeat to review the last
15 seconds of tape (SLP mode).
Highlight “ Disc Menu”, then press the ENTER
button.
- Information
Highlight “Information”, then press the ENTER
button.
6
Shuttle
In Play mode, Shuttle >> gradually increases
the cue speed: Double Speed playback - Picture
Search - Jet Search. Shuttle << gradually
slows down the tape, then goes into Slow mode,
Still mode, Reverse Picture Search and Reverse
Jet Search.
- Zoom
Highlight “Zoom”, then press the ENTER button.
- Bookmark
Highlight “Bookmark”, then press the ENTER
button.
- Repeat
Highlight “Repeat”, then press the ENTER button.
PLAY
- EZ View
Highlight “EZ View”, then press the ENTER
button.
DVD Function
0:00:00 SP
Title Menu
Disc Menu
Information
Zoom
Press the INFO. button to see the current status of
the VCR deck, as well as the tape counter position
and record speed.
Bookmark
Repeat
EZ View
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-28
Tracking
Auto Play
The Tracking adjustment removes the white lines that
sometimes appear during playback because of slight
differences in recording decks. The TRK button will
automatically align the recorded tracks with the
playback heads to solve this problem. You may also set
tracking manually.
If you want your videotapes to play automatically when
you insert them, turn on Auto Play.
NOTE: Only tapes that are missing the Record Safety
Tab will play automatically when inserted.
1
Adjust Tracking Manually
During playback, press the CH/TRK
/
buttons to remove white lines from the picture.
1
2
3
Open the “MENU”
With the VCR in Stop or Play mode, press the
MENU button.
Select “VCR”
Using the UP/DOWN buttons, move the selection
bar to “VCR” then press ENTER to select.
Select “Tape Length”
Press the RIGHT button to select the Tape Length.
This information is usually printed on the tape box.
The menu cycles through: T-120, T-160 or T-180.
Once the type of cassette is set, the VCR can
display the amount of time remaining on the tape
when you press the INFO. button.
T-120
T-160
T-180
n
4
Select “Auto Play”
Move the selection bar to “Auto Play,” then press
right button to select from the following options:
• On - The VCR will automatically begin playing a
video tape when it is inserted, as long as the
safety tab of the cassette has been removed.
• Off - Auto play is disabled.
On
Off
n
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-29
Variable Search System
5
Select “Auto Repeat”
Press the SEARCH button to display the search screen
in the stop mode. When a program is recorded, the
starting point is given an Index mark for easy location.
However, the VHS Index Search System (VISS) cannot
recognize index marks made by old VCRs. If the VCR
has trouble finding a mark, it is probably because the
cassette was recorded on a VCR without VISS. If you
want to index two programs in a row, set your VCR to
stop, then start recording each program. Pause has no
effect on index marks.
Move the selection bar to “ Auto Repeat”. It sets the
VCR to play a tape repeatedly [unless a tape
control is activated (stop, fast forward or rewind)].
n
Off
On
1
Go to [0:00:00] stop
Use this feature when you want to search for the
[0:00:00] counter position on a cassette. Press the
CLEAR button at the point on the tape where you
want to set the counter to [0:00:00]. While a
cassette is stopped, press the ENTER button. The
VCR will rewind or fast forward, searching for the
[0:00:00] counter position, and then automatically
stop at that position.
S-VHS Playback
Forward
Reverse
The DVD-VCR allows you to playback high quality
S-VHS tapes.
1
2
Insert a S-VHS Tape
Insert an S-VHS tape into the VCR deck.
2
3
End search
Use this feature when you want to search for a
blank position to record a program on a cassette.
While a cassette is stopped, press ENTER button.
The VCR will fast forward, searching for a blank
position, and then automatically stop at that
position. If the VCR reaches the end of the tape
during end search, the tape will be ejected.
Start Playback
Press ❿ll(PLAY/PAUSE) on the remote control to
begin playback of the S-VHS tape.
Scan and play
Use scan and play when you don’t know exactly
where a program is located on a cassette tape.
- Forward Intro Scan
Highlight “Forward Intro Scan”, then press the
ENTER button.
- Reverse Intro Scan
Highlight “Reverse Intro Scan”, then press the
ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-30
Basic Recording
Special Recording Features
You can record a TV show in progress by inserting a
While a recording is in progress, you can watch a
different channel, watch a DVD, or add recording time
in 30-minute increments.
blank tape and pressing the
ꢁ(REC) button. You can
even add time in 30-minute increments up to 4 hours
by pressing the (REC)button repeatedly; see page 31.
ꢁ
NOTE: Be sure your videotape has a Record Safety Tab.
If the tab is missing, you can cover the opening
with a small piece of tape. Warning: Do not
cover this opening unless you are sure you want
to record over the tape.
1
Pause/Resume Recording
Press the ❿ll(PLAY/PAUSE) button.
Press
Stop Recording
Press the (STOP) button.
ꢁ(REC) again to resume.
2
3
Before You Begin...
ꢀ
• Power on the DVD-VCR
• Power on the TV
Watch a Different Channel
While a recording is in progress, Change the
connection of your TV from Line to Antenna. Using
your TV remote control, Change the channel you
want to watch.
4
5
To Watch a DVD
Insert a DVD in the DVD deck and press ❿ll
(PLAY/PAUSE). The output will automatically
change to the DVD.
Add Recording Time
See One-Touch Recording (OTR) on the following.
1
2
Insert Tape
Insert a blank VHS tape into the VCR deck.
• Make sure the tape is long enough to record the
entire program.
To change the Recording Speed, see page 31.
Select a Channel to Record
Use the 0–9 buttons or the Channel UP/DOWN
arrow buttons to select the desired channel, or
press the INPUT SEL. button to select Line 1 or 2 if
recording from an external device connected to
the front or rear Line inputs, respectively.
3
Start Recording
Press the
ꢁ(REC) button on the remote control or
front panel.
For options while recording is in progress, see
“Special Recording Features”.
①
Recording from the DVD player to the VCR is not
possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-31
One-Touch Recording (OTR)
Record Speed
One-Touch Recording (OTR) allows you to add
recording time in 30-minute increments up to 4 hours
at the touch of a button.
You can slow down the recording speed from SP to SLP
in order to fit six hours of programming on a T-120
tape.
1
2
Start Recording
Follow the instructions on page 30 to begin
recording.
1
2
Start Recording
Follow the Basic Recording instructions on page 30.
Set Record Speed
Activate OTR
While in Record mode, press the
again to activate One-Touch Recording (OTR).
• Record length 0:30 appears on the On-Screen
Display and the DVD-VCR will record for exactly
30 minutes.
Press the SPEED button on the remote control to
set the Record Speed to one of the following
options:
ꢁ(REC) button
• SP – Standard Play, for best quality.
• SLP – Super Long Play, for maximum recording
time (3 times SP).
NOTE: The selected Record Speed will appear on the
front panel display and on-screen display.
Record
07
Maximum Recording Time - SP vs. SLP
Tape Length
T-120
SP (Standard Play)
2 hrs
SLP (Super Long Play)
6 hrs
8 hrs
9 hrs
SP
T-160
2hrs 40 mins
3 hrs
T-180
3
Add Recording Time
Continue pressing REC
ꢁ
(
)
to add recording time in
30 minute increments up to 4 hours.
• The DVD-VCR stops recording automatically
when the time has elapsed. And DVD-VCR will
be Automatically turned off when the OTR
finished.
How to Set a Timer Recording
0:30
1:00
1:30
Record
length
0:30
07
Insert a blank videotape into the VCR deck. Be sure to
leave the Record Safety Tab intact.
With the Timer Recording function, you can program
up to 7 events at a time to record up to a month in
advance.
4:00
To Begin Setting the Timer Recording,
SP
• Turn on your DVD-VCR, and
• Turn on your TV.
1
2
3
Open “MENU”
Press the MENU button or the TIMER button while
the VCR is in Stop or Play mode.
Select “Program”
Use the UP/DOWN buttons to highlight
“PROGRAM” then press the ENTER button.
Select Channel Number
Use the Right and UP/DOWN buttons to set the
channel. Press the RIGHT button to move to the
next setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-32
How to Set a Timer Recording
Function (VCR)
4
5
Set “Time/Date/Speed”
1
2
3
Open “MENU”
In the DVD in Stop or Play mode, press the MENU
button.
Repeat Step 3 above to set start time, end time,
date and record speed. Date can be set for one
time, daily or weekly recording. See below.
Select “FUNCTION”
Use the UP/DOWN buttons to highlight
“FUNCTION” then press the ENTER button.
Daily/Weekly Date Programming
Press the RETURN button to finish setting the timer
recording. Stop the VCR or turn the power off.
Then the VCR will automatically turn on and begin
recording at the time you set. To stop the timer
recording, press the POWER button or press the
Select “VCR Function”
Using the UP/DOWN buttons to highlight “VCR
Function” then press ENTER to select.
ꢀ
(STOP) button twice.
Timer Program
If you want to set
the timer program,
press the ENTER key
4
Select “Go to [0: 00: 00]”
Highlight “Go to [0: 00: 00]”, then press the
ENTER button.
6
7
Auto Speed Select
If the length of the videotape is not long enough for
a timer recording in the SP mode, set the recording
tape speed to “AUTO”. Recording will start in the
SP mode. If the length is not long enough, the tape
speed will automatically change from SP mode to
SLP mode.
- End Search
Highlight “End Search”, then press the ENTER
button.
- Forward Intro Scan
Highlight “Forward Intro Scan”, then press the
ENTER button.
Save “Timer Recording”
Weekly [Sun’s~Sat’s]: Use this to record TV
programs on the same channel at the same time
every week. Daily [MO - FR] : Use this to record TV
programs on the same channel at the same time
every day Monday through Friday.
- Reverse Intro Scan
Highlight “Reverse Intro Scan”, then press the
ENTER button.
No
Ch
Start
End
Date
Speed
Forward
Reverse
1
2
3
4
5
6
7
:
:
:
:
:
:
:
:
:
:
:
:
:
:
/
/
/
/
/
/
/
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-33
Technical Specifications
AUDIO
2 Stereo audio inputs, RCA Connector, -8dbm, 47KΩ,
front and rear
Inputs
VIDEO
2 Composite video inputs, RCA Connector, 75Ω, 1Vp-p
Antenna or CATV Input, F-Connector, 75Ω
1 Stereo audio outputs, RCA Connector, -8dbm, 1.5KΩ
1 Digital audio output (1 coaxial)
1 pair Stereo audio outputs
RF
AUDIO
AUDIO (DVD only)
VIDEO
1 Composite video output, RCA Connector, 75Ω, 1Vp-p
1 S-Video output, S-Connector, 75Ω, Y=1.0Vp-p,
C=0.286Vp-p
Outputs
VIDEO (DVD only)
1 Component video output, 75Ω, Y=1.0Vp-p, Pb=0.7Vp-p,
Pr=0.7Vp-p
RF
Channel 3 or 4
VIDEO SYSTEM
1/2-inch VHS system, 4 rotary head helical scanning;
FM azimuth luminance;chrominance: converted sub system
phase shift
AUDIO TRACK
PLAY/RECORD TIME
FF/REW TIME
HEADS
Normal: 1 track; Hi-Fi: 2 track
T-180 tape: SP 3 hours, SLP 9 hours
T-120 tape: <2 minutes
VCR
Video:
Audio:
DA 4 rotary
2 rotary heads (Hi-Fi); 1 stationary head (Linear)
Control: 1 stationary head
Erase:
1 full track, 1 audio track
WOW & FLUTTER
FREQ. RESPONSE
DISC COMPATIBILITY
Less than 0.005% (Hi-Fi)
20-20,000 Hz (Hi-Fi)
CD, CD-R, CD-R/W
DVD-Video, CD-Digital Audio (5” and 3.5”)
96/48 kHz Sampling: 4 Hz-22kHz
110 dB
DVD
FREQ. RESPONSE
S/N RATIO
DYNAMIC RANGE
THD
96 dB
0.003 %
POWER REQUIREMENT 100-240V AC, 60 Hz, 25 watts
ENVIRONMENT
WEIGHT
41-104
˚F (5-40˚C); 10%-75% humidity
SYSTEM
13.8 lbs.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-34
SAMSUNG COMBINATION DVD & VCR
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and
delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufac-
turing defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in
the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and
service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original
dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized ser-
vice center. Transportation of the product to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the limited warranty period specified above. All
replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement
parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.
SAMSUNG ís obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand
name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if
provided, are on an ”AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may
provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except
to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply
to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications
and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior fin-
ish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utili-
ties, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not sup-
plied and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical
line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, main-
tenance and environmental instructions that are covered and prescribed in the instruction book; product removal or
reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and
delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REV-
ENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN
THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIM-
ITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHAS-
ER AND PURCHASERíS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR
INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG.
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PROD-
UCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you spe-
cific legal rights, and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
S
AMSUNG CUSTOMER CARE CENTER
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856, Tel: 973-601-6000, Fax: 973-601-6001
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-35
ELECTRONICS
SAMSUNG ELECTRONICS AMERICA, INC.
HEADQUARTERS
105 Challenger Road, Ridgefield Park, N.J.
07660-0511
TEL: 1-800-SAMSUNG
SERVICE DIVISION
400 Valley Road, Suite 201, Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
AK68-00417A(01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|