SyncMaster 151MP / 171MP
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Index
Main Page
Safety Instructions
Notational
Power
Adjusting Your LCD Monitor
User Controls
User control buttons
Direct-Access Features
On-Screen Display
OSD Functions
Installation
Cleaning
Other
Introduction
Unpacking
Front
Screen Adjustment Animation Clips
Troubleshooting
Check before Calling for Service
Rear
Problems and Solutions
Q & A
Remote Control
Setup
Specifications
Connecting Your Monitor
General Specifications
PowerSaver
Connecting to a Computer
Connecting to Other Devices
Installing the Monitor Driver
Automatic
Preset Timing Modes
Information
Service Center
Terms
Manual
Installing a VESA Base
Folding or removing the base
Installing a VESA Base
Regulatory
Natural Color
Authority
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Safety Instructions > Notational
Notational
Power
Installation
Cleaning
Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Prohibited
Important to read and understand at all times
Disconnect the plug from the outlet
Do not disassemble
Do not touch
Grounding to prevent an electric shock
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Safety Instructions > Power
When not used for extended periods of time, set your PC to DPMS. If using a screen
saver, set it to the active screen mode.
Notational
Power
Do not use a damaged or loose plug.
Installation
Cleaning
Other
z
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause an electric shock or fire.
z
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
z
Do not excessively bend the plug and wire nor place heavy objects upon them,
which could cause damage.
z
This may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not
used for a long period of time.
z
Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
This may cause a fire.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Safety Instructions > Installation
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
z
Notational
Power
Installation
Cleaning
Other
Put your monitor in a location with low humidity and a minimum of dust.
An electric shock or fire could result inside the monitor.
z
Do not drop the monitor when moving it.
This may cause damage to the product or human body.
z
Place the monitor on a flat and stable surface.
The monitor can cause injury by falling.
z
Set down the monitor carefully.
It could be damaged or broken.
z
Do not place the monitor face down.
The TFT-LCD surface may be damaged.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Safety Instructions > Cleaning
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly
moistened, soft fabric.
Notational
Power
Do not spray detergent directly on the monitor.
Installation
Cleaning
Other
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly
with a dry cloth.
z
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on the monitor.
z
z
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug and then
contact a service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Safety Instructions > Ohter
Do not remove cover(or back). No user serviceable parts inside.
z
z
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
Notational
Power
Installation
Cleaning
Other
If your monitor does not operate normally - in particular, if there are any unusual
sounds or smells coming from it - unplug it immediately and contact an
authorized dealer or service.
z
This may cause an electric shock or fire.
Do not place any heavy objects on the monitor.
This may cause an electric shock or a fire.
z
For each hour of looking at the monitor, you should let your eyes rest for 5
minutes.
z
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
This may cause an explosion or fire.
z
Do not try to move the monitor by pulling on the wire or the signal cable.
z
This may cause a breakdown, electric shock or a fire due to damage to the
cable.
Do not move the monitor right or left by pulling only the wire or the signal cable.
z
This may cause a breakdown, electric shock or a fire due to damage to the
cable.
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Introduction > Unpacking
Please make sure the following items are included with your monitor. If any items are missing, contact
your dealer.
Unpacking
Front
Rear
Remote Control
User's Guide and Natural Color/
Power Cord
Signal Cable(15 pin D-Sub)
Driver Installation CD
Quick Setup Guide
DC Adapter
Warranty Card
(Not available in all locations)
Monitor
TV Tuner Box (Option)
Batteries (AAA X 2)
Audio Cable
Remote Control
Scart Jack
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Introduction > Front
For detail information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor.
The monitor's front configuration may vary slightly depending on the monitor model.
Unpacking
Front
Rear
Remote Control
1 PC mode button
2 PIP mode button
6 Up-Down button / Channel
button
7 Left-Right button / Volume
button
3 Video mode button
8 Menu button
9 Exit button
4 Audio mode button
5 Power button / Power indicator
10 Auto button
PIP(Picture in Picture)?
Feature allowing one program to be viewed on the entire screen while
one or more programs play in small windows superimposed over the
base program. PIP is also referred to as Split Windows.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Introduction > Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
Unpacking
Front
Rear
Remote Control
A
1
2
3
PC Connection Terminal
Power Connection Terminal (12V DC)
Computer Connection Terminal (15 Pin D-SUB)
Audio Connection Terminal (Audio (ST))
B
1
2
3
4
AV Connection Terminal
AV right audio connection terminal (R)
AV left audio connection terminal (L)
AV video connection terminal
S-Video connection terminal
C
D
Antenna Connection Terminal
(When TV is connected)
Headphone connection terminal
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Introduction > Remote Control
For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls >
User Control Buttons > Remote Control buttons.
The remote control's configuration may vary slightly depending on the monitor model.
The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and
right of the monitor's Remote Control Reception sensor.
Unpacking
Front
Button Names | Replacing Batteries | Usage
Rear
Remote Control
1. Button Names
1 Power button
2 PC mode button
3 PIP(Picture-in-Picture) mode button
4 Video mode button
5 Audio mode button
6 PIP Position button
7 PIP Size button
8 Up-Down button / Channel button
9 Left-Right button / Volume button
10 Menu button
11 Exit button
12 Mute button
13 Channel button
14 Display button
15 Previous channel button
16 Auto button
17 Channel search button
18 MTS/S-mode button
19 Caption button
2. Replacing Batteries
1. Slide out the cover pressing part marked
.
2. Insert the batteries matching their polarities (+, -).
3. Slide in the cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Connecting Your Monitor > Connecting to a Computer
Connecting to a Computer
Connecting to other devices
Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
1. Connecting to a Computer
1. Connect the power cord to the DC adapter and connect the adapter jack to the DC12V power port on the
back of your monitor.
2. Connect the signal cable to the video port on your computer.
3. Connect the audio cable for your monitor to the audio port on the back of your computer.
4. Turn on both your computer and the monitor.
5. You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You
don't need to install any separate speakers for your computer.)
Contact a local Samsung Electronics service center to buy optional items.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Connecting Your Monitor > Connecting to other devices
Connecting to a Computer
Connecting to other devices
AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor.
For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
Connecting AV Devices | Connecting TV | Connecting to a Macintosh | Connecting Headphone
1. Connecting AV Devices
The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You
may enjoy AV signals as long as the monitor is turned on.
1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the
monitor using the RCA or S-VHS cable.
S-VHS or RCA cable is optional.
2. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio
input terminals using audio cables.
3. Select Video or S-Video that is connected to a DVD, VCR or Camcorders using the Source button on the
monitor's front.
4. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
2. Connecting TV (Connect a TV tuner box (not included))
With a TV tuner box (not included), you can watch TV simply by hooking up the monitor to an antenna or to your
cable box. There is no need to buy a TV card which connects to a PC, or additional hardware or software.
Contact a local Samsung Electronics service center to buy optional items.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Connect the antenna or the cable box to the TV tuner box (not included) using the "ANTENNA" terminal on
the tuner box.
2. Remove the TV Tuner Box cover from the rear of the monitor.
3. Insert the connected tuner box into the slot and firmly tighten the two screws using a coin to lock the box in
place. (Loose screws may cause a blank screen or picture noise)
4. Replace the TV Tuner Box cover.
5. Turn on the monitor.
6. Select TV using Source button among the external signal adjustment buttons.
7. Select a desired TV channel.
As this product is designed for PAL or SECAM signals only, you cannot view TV programs in countries
where NTSC signals are used.
3. Connecting to a Macintosh
1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC12V power port on
the monitor. (Voltage is automatically adjusted by the power adaptor.)
2. Connect the signal cable to the D-SUB port on the Macintosh computer.
3. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh adapter
(optional) referring to the switch configuration table shown on its rear.
4. Turn on the monitor and Macintosh.
Contact a local Samsung Electronics service center to buy optional items.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connecting Headphone
You may connect your headphones to the monitor.
1. Connect your headphones to the Headphone-out port.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Installing the Monitor Driver > Automatic
Automatic
Manual
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this
monitor. Driver installation is slightly different from one operating system to another. Follow the
directions as appropriate for the operating system you have.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
Prepare a blank disk and download the driver program file at the Internet web site shown here.
z
http://www.sec.co.kr/monitor/ (Korea)
Windows ME | Windows XP/2000
1. Windows ME
Refer to "Installing the Monitor Driver and User Manual" CD-ROM supplied with the monitor.
When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up
automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer.
1. Insert CD into the CD-ROM driver.
2. Click "Windows ME Driver"
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
2. Windows XP/2000
Refer to "Installing the Monitor Driver and User Manual" CD-ROM supplied with the monitor.
When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up
automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Insert CD into the CD-ROM driver.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. If you can see following Message window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.
The certified driver will be posted on Samsung Monitor Homepage
6. Monitor driver installation is completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Installing the Monitor Driver > Manual
Automatic
Manual
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this
monitor. Driver installation is slightly different from one operating system to another. Follow the
directions as appropriate for the operating system you have.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
Prepare a blank disk and download the driver program file at the Internet web site shown here.
z
http://www.sec.co.kr/monitor/ (Korea)
To install the monitor driver manually, follow the procedures explained below after checking your operating
system.
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux
®
®
1. Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click
the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.
The certified driver will be posted on Samsung Monitor Homepage
9. Click the "Close" button then click "OK" button continually.
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Monitor driver installation is completed.
®
®
2. Microsoft Windows 2000 Operating System
* When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
* How to install
1. Click "Start" , "Setting" , "Control Panel".
2. Double click the "Display" Icon.
3. Choose the "Settings" tab and then click "Advanced..".
4. Choose "Monitor".
Case 1:
If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation.
Case 2:
If the "Properties" button is active, click the "Properties" button then follow next steps continually.
5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then
click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click
the "Finish" button then the "Close" button.
®
®
3. Microsoft Windows Millennium Operating System
1. Click "Start" , "Setting" , "Control Panel".
2. Double click "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.
8. Click the "Have Disk" button
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your
computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
(You can get some other screen for warning message or others, then click the appreciate option for your
monitor.)
Download from Www.Somanuals.com. All Manuals Search And Download.
®
®
4. Microsoft Windows NT 4.0 Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal,
change to a different mode (lower mode of resolution, colors or frequency).
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to
the Preset Display Modes in the user guide.
5. Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press Enter at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Installing a VESA base > Folding or removing the base
Folding or removing the base
Installing a VESA base
This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use
in order to install a VESA base.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
Folding the base | Removing the base
1. Folding the base
The monitor may be reclined from 0 to 90 degrees. When fully folded (reclined), the base becomes a handy
holder for moving the monitor around.
1. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
2. Disconnect the monitor cables.
3. Fully recline the monitor backward pressing the FOLD button.
4. Reconnect the monitor cables.
You may install a VESA base when the monitor base is fully folded.
2. Removing the base
You can separate the base from the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
2. Disconnect the monitor cables.
3. Remove the four bolts that fasten the base to the monitor.
4. Reconnect the monitor cables.
You may install a VESA base when the monitor base is separated.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Setup > Installing a VESA base > Installing VESA base
Folding or removing the base
Installing a VESA base
The monitor supports VESA mounting standard for use with various VESA mounting devices.
This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad.
You need to fold the monitor base before installing a VESA base.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing a VESA
base
Align the four bolt holes (1) on the monitor base with the holes (2) on the VESA base and then fasten the base
with the four bolts (3) supplied.
Only the supplied bolts should be used.
Samsung Electronics will not be responsible for damages caused by using a base other than those specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Adjusting Your Monitor > User Controls > User control buttons
User control buttons
Direct-Access Features
The control button configuration may vary slightly depending on the monitor model.
Source Buttons | Control Buttons | Remote Control Buttons
User Controls
On-Screen Display
| Source Buttons |
1.
PC mode button
Switches from Video mode to PC mode.
2.
PIP mode button
In PC Mode, turns on Video or TV screens in PIP mode. Using this function, you may view a Video or TV
program while performing PC work. (PIP mode button works in PC mode only.)
To switch Screen modes: [PC + Video] --> [PC + S-Video] (Press here to view Screen Mode Switching
Animation Clips)
3.
4.
Video mode button
Switches from PC mode to Video mode. The image size automatically switches to Full when Video mode is
on.
To switch Screen modes: [Video] --> [S-Video] (Press here to view Screen Mode Switching Animation Clips)
Audio mode button
Adjusts Audio mode. You may switch to the Audio signal for the current display mode when the wrong audio
is playing.
To switch Screen modes: [PC] --> [Video] (Press here to view Screen Mode Switching Animation Clips)
To switch PIP mode: [PC + Video] --> [PC + S-Video] --> [PC + TV]
(Press here to view Screen Mode Switching Animation Clips)
To switch Video mode: [Video] --> [S-Video] --> [TV]
(Press here to view Screen Mode Switching Animation Clips)
To switch Audio mode: [PC] --> [Video] --> [TV]
(Press here to view Screen Mode Switching Animation Clips)
Download from Www.Somanuals.com. All Manuals Search And Download.
| Control Buttons |
For more information on the screen adjustment functions, refer to On-Screen Display.
5.
6.
7.
Power button / Power indicator
Use this button to turn the monitor on and off. Power Indicator shows PowerSaver mode by green blinking.
Refer to Specifications > PowerSaver.
+ CH / - CH button
Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV
channels. For more information, refer to Direct-Access Features > Channel.
VOL - / VOL + button
Moves from one menu item to another horizontally or adjusts selected menu values. Also adjusts the audio
volume. For more information, refer to Direct-Access Features > Volume.
8.
9.
Menu( ) button
Use this button to open the OSD and activate a highlighted menu item.
Exit button
Exit button exits from the menu screen or closes screen adjustment menu.
28. Auto button
Auto button adjusts the screen automatically. For more information, refer to Direct-Access Features >
Automatic Save.
| Remote Control Buttons |
For more information on the screen adjustment functions, refer to On-Screen Display.
1 Power button
2 PC button
3 PIP(Picture-in-Picture) button
4 Video button
5 Audio button
6 PIP Position button
7 PIP Size button
8 Up-Down button / Channel button
9 Left-Right button / Volume button
10 Menu button
11 Exit button
12 Mute button
13 Channel button
14 Display button
15 Previous channel button
16 Auto button
17 Channel search button
18 MTS/S-mode button
19 Caption button (Not supported)
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2-5
6
Power button
Use this button to turn the monitor on and off.
Source Button
See the Source Buttons above.
PIP Position button
Adjusts the location of Video image in PIP mode. Press VOL - / VOL +
adjust the location up and down or left and right.
,
+ CH / - CH buttons to
7
PIP Size button
Adjusts the PIP image size in PIP mode. Use the VOL - / VOL + buttons to exit PIP mode, or reduce or
enlarge the PIP screen.
8-11
12
Control Buttons
See the Control Buttons above.
Mute button
Pauses (mutes) the audio output temporarily. The audio resumes if Mute or VOL - / VOL + button is
pressed in the Mute mode.
13
14
Channel button
Selects TV channels in the TV mode. You may use this button in PIP mode as well.
Display button
Shows a Video Source, Audio Source, current channel number, an audio type and Speaker Mute ON/OFF
on the upper right corner of the screen.
15
16
Previous channel button
This button is used to return to the immediately previous channel.
Auto button
Adjusts the screen display automatically. For more information, refer to Direct-Access Features >
Automatic Save.
17
18
Channel search button
Automatically scans and registers TV channels available (viewable) in the current location. For detailed
information on adjusting the TV screen, refer to OSD Functions > TV Screen.
MTS/S-mode button
When you press this button, current audio mode is displayed on the lower left corner of the screen.(Only
TV Screen)
Audio Type
Mono
MTS/S_Mode
Mono
Default
Automatic Change
Mono
FM Stereo
Stereo
SAP
Mono <--> Stereo
Mono <--> SAP
19
Caption button
This model does not support this function.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Adjusting Your Monitor > User Controls > Direct-Access Features
User control buttons
Direct-Access Features
Direct-Access Features let you display Monitor Adjustment Menu by simply pressing Auto button once. Or they
are used to adjust monitor functions. You need to activate functions other than Auto Adjustment only when Auto-
Access Features are off.
User Controls
On-Screen Display
Automatic Save | OSD Lock/Unlock | Volume | Channel
1. Automatic Save
The monitor display becomes more stabilized if adjusted by Auto Adjustment
functions when the monitor is installed for the first time. Try Auto Adjustment
before attempting Manual Adjustment. Ensure the clock frequency of the monitor
matches that of the computer video card before carrying out Auto Adjustment.
When the Auto button is pressed, the monitor screen turns black and the Auto
Adjustment screen appears as shown in the animated screen on the left.
To make the automatic adjustment function sharper, execute the 'AUTO' function while the
AutoPattern.exe is on.
2. OSD Lock/Unlock
This function allows you to secure the current settings so that they cannot be
inadvertently changed.
With the OSD screen off, push and hold the Menu button for at least 5 seconds to
lock or unlock the controls.
The following functions are available even while the OSD menu is locked.
1. Control buttons
Source button, PIP button, Volume button, Channel
button, Menu button, Exit button, Auto button
Brightness, Contrast
2. PC Screen
3. TV Screen
Channel, Volume
With the OSD screen off, push and hold the Menu button for five or more seconds to unlock the OSD settings.
3. Volume
When OSD is not on the screen, push the VOL - / VOL + button to adjust
volume.
1. Push the button to decrease the volume.
2. Push the button to increase the volume.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Channel
When OSD is not on the screen, push the + CH / - CH button to select
channel number.
1. Push the button to decrease the channel number.
2. Push the button to increase the channel number.
This function is available in TV or PC + TV (PIP) mode only. You need to connect a TV tuner box (not
included) to make PC+TV mode appear in TV mode or PIP mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Adjusting Your Monitor > On-Screen Display > OSD Functions
OSD Functions
Screen Adjustment Animation Clips
Characters and icons become highlighted in blue during adjustment for each menu.
PC Screen | Video Screen | TV Screen | OSD Control
User Controls
On-Screen
Display
1. PC Screen
For detailed information on Screen Adjustment in the PC mode, refer to PC Screen Adjustment
Animation Clips.
Contrast
Adjust Contrast.
Brightness
Adjust Brightness.
Color Control
The tone of color can be changed from redish white to bluish white. The individual color components
are also user customizable.
: Plain white.
1) Mode 1
2) Mode 2
3) Mode 3
4) User Mode
: Reddish white.
: Bluish white.
: User customizable.
: Color parameters are replaced with the factory default values.
5) Reset
Image
This menu includes Image Lock, Image Size and Image Effect as its sub-menu.
:
1) Image Lock
Image Lock is used to fine tune and get the best image by removing noises that creates unstable
images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment,
use the Coarse adjustment and then use Fine again.
Removes noise such as vertical stripes. Coarse adjustment may move the
screen image area. You may relocate it to the center using the Horizontal
Control menu.
• Coarse:
• Fine:
Removes noise such as horizontal stripes. If the noise persists even after Fine
tuning, repeat it after adjusting the frequency (clock speed).
Display current display mode.
• Information:
• Reset:
Image lock and position parameters are replaced with the factory default
values.
:
2) Image Size
Allows choosing from different image sizes.
(Varies depending on the resolution or signal ratio. The Expand 1, Expand 2 and 1:1 functions work
only in PC RGB.)
Performs full screen image expansion. (No change if the resolution is set at
maximum)
• Expand 1:
• Expand 2:
• Normal:
Performs image expansion while maintaining the vertical/horizontal aspect ratio of
the original video resolution. (No change if the resolution is set at maximum)
Displays the image as created by the signal source. (No change if the resolution is
set at maximum.)
Magnifies an image up to 64 times the original size.
• Zoom:
• Pan:
Moves the position of the magnified image on the screen either vertically or
horizontally.
:
3) Image Effect
Download from Www.Somanuals.com. All Manuals Search And Download.
Image being displayed can be made softer or sharper.
Position
This adjusts the screen location horizontally and vertically.
Sound
The monitor has a built-in high fidelity stereo audio amplifier.
: Emphasize low frequency audio.
1) Bass
: Emphasize high frequency audio.
2) Treble
3) Surround
: Turns the surround sound feature on/off.
PIP
When external A/V devices such as VCR or DVD are connected to the monitor, PIP allows you to
watch video from such devices in a small window super-imposed on pc video signal.
: Allows the user to turn off or adjust the size of the PIP screen.
1) Size
2. Video Screen
For detailed information on Screen Adjustment in the Video mode, refer to Video Screen Adjustment
Animation Clips. Screen Adjustment in the Video mode does not affect the PC screen at all.
Picture
Controls Contrast, Brightness, Sharpness, Color and Tint of the video image.
: Adjust the contrast of video without affecting PC RGB's contrast.
1) Contrast
: Adjust the brightness of video without affecting PC RGB's brightness.
2) Brightness
: Adjust the sharpness of video image.
3) Sharpness
: Change the richness of color.
: Picture parameters are replaced with the factory default values.
4) Color
5) Reset
Sound
The monitor has a built-in high fidelity stereo audio amplifier.
: Emphasize low frequency audio.
1) Bass
: Emphasize high frequency audio.
2) Treble
3) Surround
: Turns the surround sound feature on/off.
Active Area
The user can adjust the scope of the image shown on the screen by zooming in or zooming out.
* This feature does not work in PIP mode.
Timer
Automatically shuts off the screen at a pre-programmed time (30 min., 60 min., 120 min.).
3. TV Screen
For detailed information on Screen Adjustment in TV mode, refer to TV Screen Adjustment
Animation Clips. Screen Adjustment in TV mode does not affect the PC screen at all.
You can use this function only if your monitor is connected to a TV tuner box (not included).
Your TV tuner box is not properly connected to the monitor if the Video Adjustment icon shows an
adjustment screen.
Set-up
The channel system can be set in several different ways.
:
1) Channel System
Select a channel system that is being used in your region.
Download from Www.Somanuals.com. All Manuals Search And Download.
Upon selecting a channel system, you will be asked if you want to perform "Channel auto program".
Select "OK" to perform the "Channel auto program" or select "Cancel" to select different channel
system.
: Beligie, Deutschland, Espania, France, Italia, Nederland, Schweiz, Sverige, UK, East Europe.
:
2) Manual Tune
Due to the weak signals or a wrong antenna configuration, some of the channels may not be tuned
correctly or there could be a mismatch of the channel number between a Real channel and a
Program channel. Use this menu to fine tune and perform necessary corrective actions.
•
•
•
•
:
Program numbers are given in a sequentrial manner based on the search
order of Channel Auto Program.
Program
:
Channel numbers are given according to the CCIR or Australia standard
channel table.
Channel
:
Adjust repeatedly until the sound is of the best quality.
(BG <-> DK <-> I <-> L <-> L')
Sound System
:
Adjust repeatedly until the color is of the best quality.
(Auto <-> PAL <-> SECAM <-> NTSC 4.4)
Color System
•
•
:
To select the "Fine tune" and press the or button.
Fine Tune
:
Use VOL - / VOL + buttons to fine tune the picture quality and then select
"Save" menu. Now press "Menu" button to save the fine tuned channel.
Save
•
:
Use this function to add a real channel. Use VOL - / VOL + buttons to
select a desired channel and then select "Add" menu. Now press "Menu"
button to add the channel.
Add
:
3) Channel Sort
Channel order can be re-arranged by this menu.
For explanations on the TV control menu, refer to the explanations under Video Screen. You may
control TV Screen properties in the same way as for Video Screen.
4. OSD Control
Press the Exit button to make the menu disappear. The adjustments made are saved automatically
as the menu screen disappears. The OSD (On-Screen Display) feature may not function properly
depending on input signals.
For detailed information on screen adjustment functions, refer to OSD Screen Adjustment Animation
Clips.
Language
You can choose one of 7 languages. (English, German, Spanish, French, Italian, Swedish, Russian)
Position
Move the OSD Window to the vertical and horizontal direction.
Halftone
Change the opaqueness of the background of the OSD.
Duration
The number of seconds that the OSD will remain visible before disappearing.
Beep
Press Beep to turn the beeping sound on/off when you press buttons.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Troubleshooting > Check before calling for service
Check the following items yourself before calling for service. Contact the service center for problems that you
cannot solve by yourself.
Self-Test Feature Check | Video mode not supported | Display Adapter Driver | For Better Display |
Dot Acceptable | Maintenance and Cleaning | Symptoms & Recommended Actions
Check before
calling for service
Problems and
Solutions
1. Self-Test Feature Check
Q & A
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
The figure shown below ("Check Signal Cable") appears on a black background when the monitor is in its
normal working condition though it does not sense any video signal: While in the Self-Test mode, the LED
power indicator remains green and the figure moves around on the screen.
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during
normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and computer
system; your monitor is functioning properly.
2. Video mode not supported
This indicates the display resolution or refresh rate is not properly set on your computer video card. Reboot the
computer in Safe Mode and select "Default" in the "Refresh Rate Unknown" box while setting Adapter for Display
Properties.
Contact the computer dealer or manufacturer for information on Safe Mode Booting.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported by the
monitor.
Sometimes the screen turns black without the “Video mode not supported” message appearing on the screen. This
indicates the monitor is set for a frequency out of range or the PowerSaver mode is on.
3. Display Adapter Driver
Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust
resolution, frequency or color and you cannot install the monitor driver.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Checking Adapter Driver
Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter.
If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed.
Install the adapter driver again according to the information provided by the computer or video card
manufacturers.
2. Installing Adapter Driver
The instructions given below are for general circumstances. For specific issues, contact the relevant
computer or video card manufacturers.
1) Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter --> Update
Driver --> Next --> Display a list of the known drivers for this device so that I can choose a specific
driver --> Next -> Have Disk (Insert Video Card Driver diskette) -> OK -> Next -> Next -> Finish.
2) In case you have Adapter Driver Setup file on your computer:
Run Setup.exe or Install.exe, which is found in the Adapter Driver Setup file.
4. For Better Display
1. Selecting Resolution and Color
If the monitor resolution or color is not properly set, the screen may show blurred images or mosaic patterns.
Procedures for setting frequency in the Control Panel may vary depending on the video card.
Setting Color & Resolution >>
Click Start --> Settings --> Control Panel --> Display --> Settings --> Colors & Screen area --> Apply -->
OK.
You can get the best image quality by selecting resolution depending on the monitor screen size as
follows:
• 15 inch monitor : 1024 x 768 @60Hz
• 17 inch monitor : 1280 x 1024 @60Hz
Select 16 or 24 bit color.
• Supported or not subject to the video card (the monitor is irrelevant)
• LCD monitors may display up to 16.77 million colors (24 bits).
2. Setting Refresh Rate
If the monitor refresh rate is not properly set, the screen image may be skewed or noise patterns will appear.
You can enjoy the best screen image when the refresh rate is set to 60 Hz.
Setting Refresh Rate >>
Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Refresh Rate --> Apply --
> Yes --> OK --> Yes.
3. Activate the AUTO ADJUSTMENT feature for better picture quality. If the noise persists even after AUTO
ADJUSTMENT, adjust the screen settings using FINE/COARSE tuning buttons.
5. Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is
used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or
some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
The number of TFT LCD pixels :
z
z
z
z
z
15 inch: 2,359,296
17 inch: 3,932,160
18 inch: 3,932,160
21 inch: 5,760,000
24 inch: 6,912,000
6. Maintenance and Cleaning
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Maintaining the Monitor Case
Clean with a soft cloth after disconnecting the power cord.
z
z
Do not use benzene, thinner or other flammable substances, or a wet
cloth.
We recommend a Samsung cleansing agent is used to prevent
damage to the screen.
2. Maintaining the Flat Panel Display Screen
Clean with a soft cloth (cotton flannel) smoothly.
z
z
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
The user will be required to pay costs and related expenses for repair
of damages caused by him/her.
7. Symptoms and Recommended Actions
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video
card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In
this case, first check the source of the problem, and then contact a service center or your dealer.
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver
and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the
Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to
reinstall the adapter (video) driver.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Troubleshooting > Problems and Solutions
The following table lists possible problems and their solutions. Before calling for service, check the information in
this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone
number on the warranty card, the phone number on the Information section or contact your dealer.
Installation | Screen | Audio | Remote Control
Check before
calling for service
Problems and
Solutions
1. Problems related to Installation
Q & A
Problems related to the monitor installation and their solutions are listed.
Problems
Solutions
It appears the PC does not function
normally.
z
z
Check if the Display Adapter Driver (VGA Driver) is properly
installed. (Refer to Installing Driver)
The monitor screen flickers.
Check if the signal cable between the computer and the monitor is
securely connected and tightened. (Refer to Connecting to a
Computer)
TV screen is blurred or shows noise
signals.
z
Check if the TV antenna connector is securely connected to the
external antenna. (Refer to Connecting to TV)
TV signal is not received
z
z
Check "Channel system" and make sure you choose the correct
channel system. (Refer to the Channel System)
Select "Channel auto program" to configure the channel system
automatically. (Refer to the Channel System)
2. Problems related to Screen
Problems related to the monitor screen and their solutions are listed.
Problems
Solutions
Screen is blank and power indicator
is off
z
Ensure that the power cord is firmly connected and the LCD
monitor is on. (Refer to the Connecting Your Monitor)
"Check Signal Cable" message
z
z
Ensure that the signal cable is firmly connected to the PC or video
sources. (Refer to the Connecting Your Monitor)
Ensure that the PC or video sources are turned on.
"Video mode not supported"
message
z
z
Check the maximum resolution and the frequency of the video
adaptor.
Compare these values with the data in the Preset Timing Modes
Chart.
Picture rolls vertically.
z
Check if the signal cable is securely connected. Connect it again
securely.(Refer to Connecting to a Computer)
Image is not clear. Picture is
blurred.
z
z
Run Frequency Coarse and Fine tuning.
Turn on again after removing all accessories (video extension
cable, etc.)
z
Set resolution and frequency to the recommended ranges.
15 inch model (1024 x 768 @ 60Hz), 17 inch model (1280 x 1024
@ 60Hz)
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture image is unstable and
vibrates.
z
Check if the resolution and frequency set for the computer video
card falls in the range supported by the monitor. If not, reset them
referring to the current Information under the monitor menu and
Preset Timing Modes.
Ghost images are shown in the
picture.
The image is too light or too dark
z
z
Adjust the Brightness and Contrast.
(Refer to the Brightness, Contrast)
Screen color is inconsistent.
Adjust color using User Mode under OSD Color Adjustment menu.
Color image is distorted with dark
shadows.
White color is poor.
Power Indicator blinks green.
z
The monitor is currently saving the changes made in settings to
the OSD memory.
Screen is blank and power indicator
light is steady green or blinks every
0.5 or 1 seconds
z
z
The monitor is using its power management system.
Move the computer's mouse or press a key on the keyboard
The monitor front control buttons do
not respond.
z
z
Check if OSD Lock/Unlock is on by pressing Menu button.
If the problem persists, contact the service center.
3. Problems related to Audio
Problems related to audio signals and their solutions are listed below.
Problems
Solutions
No sound
z
z
Ensure that the audio cable is firmly connected to both the audio-
in port on your monitor and the audio-out port on your sound card.
(Refer to the Connecting Your Monitor)
Check the volume level. (Refer to the Volume)
Sound level is too low.
z
z
Check the volume level. (Refer to the Volume)
If the volume is still too low after turning the control to its
maximum, check the volume control on the computer sound card
or software program.
Sound is too high pitched or too low
pitched
z
Adjust the Treble and Bass to appropriate level.
4. Problems related to Remote Control
Problems related to the remote control and their solutions are listed.
Problems
Items to check
The remote control buttons do not
respond.
z
z
z
z
z
Check the battery polarities (+/-).
Check if the batteries have been exhausted.
Check if the power is on.
Check if the power cord is securely connected.
Check if a special fluorescent or neon lamp is on in the vicinity.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Troubleshooting > Q & A
Frequently asked questions are summarized here for your reference.
Question
Answer
Check before
calling for service
Problems and
Solutions
How can I change the frequency?
How can I adjust the resolution?
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version of
the driver used. (Refer to the computer or the video card manual for
details.)
Q & A
Windows XP:
Reset resolution by clicking Control Panel --> Appearance & Theme
--> Display --> Settings.
Windows ME/2000:
Set the resolution at the Control Panel --> Display --> Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving function?
Windows XP:
Reset Power Saving parameters by clicking Control Panel -->
Appearance & Theme --> Display --> Screen Saver or in the
computer BIOS SETUP. (Refer to Windows/Computer Manual)
Windows ME/2000:
Set the function at BIOS-SETUP of the computer or the screen
saver. (Refer to Windows/Computer Manual).
How can I clean the outer case/LCD Panel?
Disconnect the power cord and then clean the monitor with a soft
cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the case. Do
not allow any water to go inside the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Specifications > General Specifications
Design and specifications are subject to change without prior notice.
General
General
Model Name
LCD Panel
Size
SyncMaster 151MP
PowerSaver
Preset Timing
Modes
15.0 inch (Diagonal)
304.1 (H) x 228.1 (V)
0.297 (H) x 0.297 (V)
a-si TFT active matrix
Display area
Pixel Pitch
Type
Viewing Angle
70/70/60/60 (L/R/U/D)
(Depending on the panel manufacturer, the viewing angle may be different
from this spec.)
Synchronization
Horizontal
30 ~ 69 kHz
56 ~ 85 Hz
Vertical
Display Color
16,777,216 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal
1024 x 768 @ 60Hz
1024 x 768 @ 85Hz
Separate: TTL, P. or N.
Composite: TTL, P. or N.
Sync-on-green: 0.3 Vp-p, N.
0.7 Vp-p @ 75 ohm
Sync.
Video signal
TV / Video
Color system
Sound system
Video format
Video
PAL, SECAM, NTSC 4.4
B/G, D/K, I, L, L'
CVBS, S-VHS
Color system
Maximum Pixel Clock
95 MHz
PAL / NTSC / SECAM
Power Supply
Input
AC 90 ~ 264 V (50/60 Hz)
DC 12V / 4.5A
Output
Power Consumption
Maximum
40W
Power Saving
Dimensions (WxHxD) / Weight
Monitor body
With stand
Less than 3W
358.6 x 351.5 x 51 mm / 3.3 kg
358.6 x 360.1 x 175.5 mm / 3.5 kg
358.6 x 402.6 x 51 mm / 3.5 kg
When folded
Download from Www.Somanuals.com. All Manuals Search And Download.
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F(10°C ~ 40°C)
Humidity : 10% ~ 80%, non-condensing
Storage
Temperature : -13°F ~113°F (-25°C ~ 45°C)
Humidity : 5% ~ 95%, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
3.5ø Stereo Jack, 0.5Vrms (-9dB)
Audio Input 2
Headphone out
Max. 10mW Output (3.5ø Stereo Jack 32ohm)
Frequency Response
RF: 80Hz ~ 15kHz (at- 3dB)
A/V: 80Hz ~ 20kHz (at - 3dB)
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation
will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright
sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without
uneasiness.
The number of TFT LCD pixels :
z 15 inch: 2,359,296
z 17 inch: 3,932,160
z 18 inch: 3,932,160
z 21 inch: 5,760,000
z 24 inch: 6,912,000
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Specifications> General Specifications
Design and specifications are subject to change without prior notice.
General
General
Model Name
LCD Panel
Size
SyncMaster 171MP
PowerSaver
Preset Timing
Modes
17.0 inch (Diagonal)
338 (H) x 270 (V)
Display area
Pixel Pitch
Type
0.264 (H) x 0.264 (V)
a-si TFT active matrix
Viewing Angle
80/80/80/80 (L/R/U/D)
(Depending on the panel manufacturer, the viewing angle may be different
from this spec.)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 85 Hz(~XGA), 60 ~76 Hz(SXGA)
Display Color
16,777,216 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal
1280 x 1024 @ 60Hz
1280 x 1024 @ 76Hz
Separate: TTL, P. or N.
Composite: TTL, P. or N.
Sync-on-green: 0.3 Vp-p, N.
0.7 Vp-p @ 75 ohm
Sync.
Video signal
TV / Video
Color system
Sound system
Video format
Video
PAL, SECAM, NTSC 4.4
B/G, D/K, I, L, L'
CVBS, S-VHS
Color system
Maximum Pixel Clock
135 MHz
PAL / NTSC / SECAM
Power Supply
Input
AC 90 ~ 264 V (50/60 Hz)
DC 12V / 4.5A
Ouput
Power Consumption
Maximum
52W
Power Saving
Dimensions (WxHxD) / Weight
Monitor body
With stand
Less than 3W
412.0 x 408.0 x 58.5 mm / 4.7 kg
412.0 x 418.0 x 203.0 mm / 5 kg
412.0 x 472.0 x 58.5 mm / 5 kg
When folded
Download from Www.Somanuals.com. All Manuals Search And Download.
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F(10°C ~ 40°C)
Humidity : 10% ~ 80%, non-condensing
Storage
Temperature : -13°F ~113°F (-25°C ~ 45°C)
Humidity : 5% ~ 95%, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
3.5ø Stereo Jack, 0.5Vrms (-9dB)
Audio Input 2
Headphone out
Max. 10mW Output (3.5ø Stereo Jack 32ohm)
Frequency Response
RF: 80Hz ~ 15kHz (at- 3dB)
A/V: 80Hz ~ 20kHz (at - 3dB)
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation
will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright
sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without
uneasiness.
The number of TFT LCD pixels :
z 15 inch: 2,359,296
z 17 inch: 3,932,160
z 18 inch: 3,932,160
z 21 inch: 5,760,000
z 24 inch: 6,912,000
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Specifications > PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by
switching your monitor into a low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you move the computer's mouse or press a key on the
keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended
for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your
computer. Use a software utility installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
SyncMaster 151MP
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Less than 3W
Power Indicator
Green
Black
Power Consumption
Less than 40W
Less than 3W
SyncMaster 171MP
Power saving mode
EPA/ENERGY 2000
State
Normal Operation
Power Switch off
Power Indicator
Green
Green, Blinking
Less than 3W
Black
Power Consumption
Less than 52W
Less than 3W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a
computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Specifications > Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be
adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer
to the video card manual and adjust the screen as follows.
General
Table 1. Preset Timing Modes
PowerSaver
Preset Timing
Modes
SyncMaster 151MP
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
VGA, 720 x 400
VGA, 640 x 480
VGA, 640 x 480
VGA, 640 x 480
SVGA, 800 x 600
SVGA, 800 x 600
XGA, 1024 x 768
XGA, 1024 x 768
XGA, 1024 x 768
31.469
31.469
37.500
43.269
46.875
53.674
48.363
60.023
68.677
70.087
59.940
75.000
85.008
75.000
85.061
60.004
75.029
84.997
28.322
25.175
31.500
36.000
49.500
56.250
65.000
78.750
94.500
-/+
-/-
-/-
-/-
+/+
+/+
-/-
+/+
+/+
SyncMaster 171MP
Horizontal Frequency
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
(kHz)
31.469
31.469
37.500
43.269
46.875
53.674
48.363
60.023
68.677
63.981
79.976
VGA, 720 x 400
VGA, 640 x 480
VGA, 640 x 480
VGA, 640 x 480
SVGA, 800 x 600
SVGA, 800 x 600
XGA, 1024 x 768
XGA, 1024 x 768
XGA, 1024 x 768
SXGA, 1280 x 1024
SXGA, 1280 x 1024
70.087
59.940
75.000
85.008
75.000
85.061
60.004
75.029
84.997
60.020
75.025
28.322
25.175
31.500
36.000
49.500
56.250
65.000
78.750
94.500
108.000
135.000
-/+
-/-
-/-
-/-
+/+
+/+
-/-
+/+
+/+
+,-/+,-
+/+
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. PAL Broadcasting Systems
Color System
Sound System
Stereo System
Channel System
CCIR
Countries
Germany, Austria,
Swiss, Netherlands
A2
AUSTRALIA
Australia
Sweden, Spain,
Denmark, Norway,
Finland, Belgium,
Iceland, Portugal,
Malaysia, Singapore,
Thailand
B/G
PAL
NICAM
CCIR
India, Israel, Kuwait,
Jordan, Yugoslavia
Unknown
NICAM
CCIR
CCIR
I
UK, Hongkong
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen
horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle
is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per
second to display an image to the user. The frequency of this repetition is called
Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Information > Service Center
U.S.A. :
Samsung Computer Products Customer Service
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856
Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864)
Fax. : (973)601-6001
Service Center
Terms
BRAZIL :
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
Regulatory
Natural Color
Authority
SAC : 0800 124 421
CANADA :
Samsung Electronics Canada Inc.
7037 Financial Drive
Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax. : (905) 542-1199
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
e-mail : soporte@samsung-latin.com
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
PERU
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
GERMANY :
TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0,12/MIN.
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
ESPAÑA :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax. : (0208) 397 9949
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
THAILAND :
HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, No2 - 1° Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Free Line 800 220 120
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
MEXICO :
Samsung Electronics Mexico S.A. de C.V.
Saturno 44 Col. Nueva Industrial Vallejo
Del. Gustavo A. Madero C.P. 07700
Mexico D.F.
Tel. 01 57 47 51 00
Fax. 01 57 47 52 02
RFC: SEM950215S98
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO S.A. DE C.V.
SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO
DEL. GUSTAVO A. MADERO C.P. 07700
MEXICO D.F. TEL. 5747-5100
RFC: SEM950215S98
EXPORTADO POR: SAMSUNG ELECTRONICS CO.,LTD.
JOONG-ANG DAILY NEWS BLDG.
7 SOON-WHA-DONG CHUNG-KU,
C.P.O BOX 2775, 1144 SEOUL, KOREA
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Information > Terms
Sync Signal
Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the
monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by
the set resolution and frequency.
Service Center
Terms
Types of Sync Signals
Separate
This is a scheme of transmitting individual vertical sync signals to the monitor.
Regulatory
Natural Color
Authority
Composite
This is a scheme of combining vertical sync signals into one composite signal and
transmitting it to the monitor. The monitor displays the color signals by separating the
composite signal into original color signals.
This scheme does not use sync signals. Instead, it combines horizontal and vertical
sync signals into a Green signal and transmits to the monitor. It is mainly used for
workstations.
Sync On Green
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution.
The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the user. The
frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this case, flickering of
the screen can be detected. To avoid this problem, there is a Flicker-free Mode using a vertical
frequency over 70 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal
Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-Interlace method
while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is
used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the monitor to
exchange information automatically. This monitor follows the international standard VESA DDC for the Plug &
Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number
shows the accuracy of the display. High resolution is good for performing multiple tasks as more image
information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal dots (horizontal
resolution) and 768 vertical lines (vertical resolution).
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Information > Regulatory
FCC Information | IC Compliance Notice | MPR II Compliance |
European Notice (Europe only) | PCT Notice | VCCI |
TCO'95-Ecological requirements for personal computers (TCO applied model only)
TCO'99-Ecological requirements for personal computers (TCO applied model only)
FCC Information
Service Center
Terms
User Instructions
Regulatory
Natural Color
Authority
The Federal Communications Commission Radio Frequency Interference Statement includes the following
warning:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television receptions,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
z
z
z
z
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment. If necessary, consult your dealer or an experienced
radio/television technician for additional suggestions. You may find the booklet called How to Identify and
Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal
Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC
20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Tel) 949-975-7310
Fax) 949-922-8301
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be
suitable for connection to any UL Listed personal computer with similar configuration. Before making the
connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor
and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage
rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type
(parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with
NEMA configuration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les
équipements produisant des interférences au Canada.
MPR II Compliance
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice (Europe only)
Download from Www.Somanuals.com. All Manuals Search And Download.
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC),
(93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following European Norms:
z
z
z
z
z
EN55022:1998 - Radio Frequency Interference
EN55024:1998 - Electromagnetic Immunity
EN61000-3-2:1995+A1+A2 - Power Line Harmonics
EN61000-3-3:1995 - Voltage Fluctuations
EN60950 - Product Safety.
PCT Notice
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment according to the instruction
manual.
TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to
reducing the burden on the environment and to the further development of environmentally-adapted
electronic products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment.The main problem as far as monitors and other
electronic equipment are concerned is that environmentally harmful substances are used both in the
products and during their manufacture. Since it has not been possible so far for the majority of electronic
equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or
later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are important
from both the working and natural environment viewpoints. Since all types of conventional electricity
generation have a negative effect on the environment (acidic and climate-influencing emissions,
radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an
enormous amount of energy, since it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The
Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for
Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in
Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The
product must be prepared for recycling and the manufacturer is obliged to have an environmental plan,
which must be adhered to in each country where the company conducts its operations policy. The energy
requirements include a demand that the monitor after a certain period of inactivity shall reduce its power
consumption to a lower level, in one or more stages. The length of time to reactivate the monitor shall be
Download from Www.Somanuals.com. All Manuals Search And Download.
reasonable for the user.
Labelled products must meet strict environmental demands, for example in respect of the reduction of
electric and magnetic fields, along with physical and visual ergonomics and good usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by this
product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In
turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. These are related to another group of environmental toxins, PCBs, which are
suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals,
due to the bioaccumulative processes. Flame retardants have been found in human blood and
researchers fear that disturbances in foetus development may occur.
z
TCO'95 demand requires that plastic components weighing more than 25 grams must not contain
organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and
is toxic in high doses.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
mercury. It also demands that no mercury is present in any of the electrical or electronics components
concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of
skin cancer (malignant melanoma).
z
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of
the product or its packaging.
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a
product developed for professional use. Your purchase has also contributed to reducing the burden on the
environment and also to the further development of environmentally adapted electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was developed
as a joint effort by the TCO(The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens Energimyndighet(The
Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric
and magnetic fields, energy consumption and electrical safety.
Download from Www.Somanuals.com. All Manuals Search And Download.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left
running continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish
Society for Nature Conservation). These demands impose restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs(freons)and chlorinated solvents, among other
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental policy which must be adhered to in each country where the company implements its
operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be obtained via the
Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose
is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can
consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame
retardants are chemically related to another group of environmental toxins, PCBs. Both the flame
retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health
effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes. Flame retardants have been found in human blood and researchers fear that disturbances in
foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the
printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99
requirement states that batteries, the colour-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light
system of flat panel monitors as today there is no commercially available alternative. TCO aims on
removing this exception when a Mercury free alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant
melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the
inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Download from Www.Somanuals.com. All Manuals Search And Download.
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)
Congratulations!
The display you have just purchased carries the TCO03 Displays label. This means that your display is
designed, manufactured and tested according to some of the strictest quality and environmental
requirements in the world. This makes for a high performance product, designed with the user in focus that
also minimizes the impact on our natural environment.
Some of the features of the TCO03 Display requirements:
Ergonomics
Good visual ergonomics and image quality in order to improve the working environment for the user and to
reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance,
colour rendition and image stability.
Energy
z Energy-saving mode after a certain time - beneficial both for the user and the environment
z Electrical safety
Emissions
z Electromagnetic fields
z Noise emissions
Ecology
z The product must be prepared for recycling and the manufacturer must have a certified environmental
management system such as EMAS or ISO 14 000
z Restrictions on
o chlorinated and brominated flame retardants and polymers
o heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in cooperation with
scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has
been involved in influencing the development of IT equipment in a more user-friendly direction. Our
labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over
the world.
For more information, Please visit
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Information > Natural Color
Natural Color Software Program
Service Center
Terms
Regulatory
Natural Color
Authority
One of the recent problems in using a computer is that the color of the images printed out by a printer or other
images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by
Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This
system is available only for Samsung monitors and makes the color of the images on the monitor the same as the
printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program
installation will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install
the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start]
button of Windows and then select [Execute].
Enter D:\color\eng\setup.exe and then press the <Entrer> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program].
Select Natural Color from the list and then click the [Add/Delete] button.
Download from Www.Somanuals.com. All Manuals Search And Download.
English > Main > Information > Authority
Information in this document is subject to change without notice.
© 2003 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly
forbidden.
Service Center
Terms
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Regulatory
Natural Color
Authority
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are
registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video
Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S.
Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has
determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names
mentioned herein may be the trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
http://www.samsung-monitor.com/ (Worldwide)
http://www.sec.co.kr/monitor/ (Korea)
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Radio Shack Cordless Telephone ET 557 User Guide
Ratoc Systems Network Card REX SMA01F User Guide
RCA Camcorder Hollywood DV Bridge User Guide
Renesas Computer Hardware H8 3644 Series User Guide
Samsung DVD Player DVD V9700 User Guide
Samsung Laptop R710 User Guide
Samsung MP3 Player NeXus 25 User Guide
Scag Power Equipment Lawn Mower SMZ 48 User Guide
Sears Blower 13874899 User Guide
Sears Trimmer 90079441 User Guide