COMBO DRIVE
SM-316
User's Guide
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be deter-mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your COMBO Drive
Upgrading the Firmware Flash Memory
The product firmware can be upgraded by downloading the updated file from the
following Web site:
System Requirements
Before you install the COMBO drive, we strongly recommend that you check that
your setup meets the system requirements listed below.
Item
Description
1
2
3
4 5 6
Computer
Intel Pentium II 300MHz/Celeron 333A(or higher),
32 MB of RAM (or higher) with an IDE interface
1. Connector for stereo headphones with a 3.6 mm stereo mini-jack
2. Headphone volume control
3. Disc compartment (the compartment opens and closes automatically
when you press the Eject button)
4. Emergency eject hole (if the compartment does not open when
you press the Eject button, power off the computer, insert a pin or
unfolded paper clip in the hole and push firmly)
5. Indicator light
Free expansion unit
Disk space
5.25 inch
700 MB minimum
Windows version
Windows 95/98/2000/ME/XP/NT4.0 OSR2 (or higher)
(For Windows NT, we recommend Service Pack2,
and Version is over 4.00.1381)
MS-DOS
5.0 or higher (For MS-DOS, The CD-R/CD-RW driver
can only read a disc without premaster Software.)
6. Eject button
DVD Video playback
PC with Windows 95/98/2000/ME/XP/NT4.0 OSR2
DVD-Video playback software and appropriate
hardware (the Power DVD MPEG software is
included in the COMBO drive package)
DVD Region Protection Coding (RPC):
The RPC feature is supported on DVD players and is used with DVD-video discs
(such as movies). Currently, the motion picture industry has divided the world into
different regions or zones that correspond to the regional markets into which the
motion picture industry releases movies. Simply put, RPC codes are placed on movies
marketed throughout the world, based on the region of the world in which they are
being sold. These RPC codes help control and prevent pirating of new movies into
other motion picture regions prior to their true release dates within those markets.
1
5
2
3
4
1. Two-pin digital audio output terminal for use with a sound or MPEG card
supporting digital audio features
2. Four-pin sound output terminal for use with a sound card
(refer to the sound card documentation for further details)
3. Master/slave select terminal
The SM-316 COMBO drive supports RPC phase II. In the RPC-2 mode, the local
code can be changed by users.
RPC-2 is selected by default for the SM-316 COMBO drive.
You can change the region code up to five times via an MPEG application.
4. 40pin host E-IDE interface connector
5. 4pin power terminal
Please contact your dealer or local SAMSUNG representative if you wish to change
the local code more than five times.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the COMBO Drive
To install your COMBO drive in the PC, proceed as follows.
2
Connecting the IDE cable
Insert the IDE cable (40-pin), which is connected to the hard disk to the interface
terminal. (Place the red line of the cable close to the Pin 1.)
1
2
Make sure that the PC is powered off and disconnected from any power source.
If necessary, attach a horizontal bracket to
both sides of the drive.
Pin 1
Key Slot
Red Line
Use of the brackets depends on your computer model;
you can purchase these accessories separately from
your computer dealer.
3
Remove the cover from a free expansion slot
and install the COMBO drive,
as shown in the illustration.
When using one E-IDE cable
If you have no free expansion slot,
install the drive in place of the
diskette drive.
COMBO Drive
cover
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at
the rear of the COMBO drive.
Slave Drive (Choose the SL Jumper)
Connecting the Cables
Motherboard
HDD
Power cable
When using two E-IDE cable
E-IDE cable
If there is only one COMBO drive, select MA (Master).
Master/slave select terminal
Audio cable
Master Drive (Choose the MA Jumper)
SEC 1
PRI1
1
Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must be
connected to the power terminal on the rear of the COMBO drive.
Motherboard
HDD
If there is two COMBO drive, select MA (Master) / SL (Slave).
Cut side
Master Drive (Choose the MA Jumper)
Slave Drive (Choose the SL Jumper)
+12V DC
Ground
SEC 1
PRI1
Ground
+5V DC
Motherboard
Note:An improperly connected power cable may cause trouble. Check the direction of
HDD
the power connector and the incline side of the COMBO drive before connecting.
(Choose the MA jumper) (Choose the SL jumper)
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the CD Record Utility
To record data on a CD-R or CD-RW disc in the COMBO drive, you must first
install the CD record utility. For compatibility reasons, you are recommended to
uninstall any existing software of the same type before installing this utility.
3
Installing a jumper on the master/slave select terminal
Connect a jumper to the rear side of the COMBO.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using
the host interface signal CSEL. (In general, connection to MA is recommended.)
1
2
Insert the disc supplied with the COMBO drive in the drive.
Follow the instructions displayed on the screen to install the utility.
Refer to the separate utility documentation for further details.
3
Store the utility disc in a safe place.
CS : Cable Select(CSEL)
SL : Slave
MA: Master
Installing the Device Driver
No additional device driver is needed for Windows 95/98/2000/ME/XP/NT4.0,
as the default Windows device driver is used. You can check that the COMBO
drive has been correctly detected by Windows. To do so, proceed as follows.
4
Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the
COMBO drive and the audio input terminal on the sound card.
1
2
Double-click on the My Computer icon on your desktop.
Double-click on the Control Panel folder.
For clearer sound, use a digital output terminal.
(Available only for the CAID that supports digital output)
This may not be available for general sound cards.
3
4
5
Double-click on the System icon.
Click on the Device Manager tab.
Sound Card
Expand the CD-ROM branch.
Sound Output Terminal
Digital Output Terminal
The SAMSUNG COMBO SM - *** device name is displayed.
The SAMSUNG device driver enables discs in the COMBO drive to be read but not
recorded in an MS-DOS environment;
the driver is located in the D driver folder on the CD record utility disc.
Audio Input Terminal
of the Sound Card
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Device Driver
Using the COMBO Drive
To play audio or video CDs and / or DVDs in your COMBO drive,
proceed as follows.
✱✱Automatic Setup
1
2
Push the power button and boot the computer.
1
Insert the setup diskette in the diskette drive and change the directory to A:,
where A: is the diskette drive.
After booting the computer, open the disc
compartment by pressing the Eject button.
To do so, type A: after the C:\ prompt and press [Enter].
3
Insert the disc (CD/DVD) with the label on the
disc facing upwards and close the disc
compartment by pressing the Eject button.
The indicator light comes on.
2 Type CDSETUP and press [Enter].
3 Reboot the computer.
4
Play the disc (CD/DVD).
Playing Audio CDs
Run the CD player supplied with Windows or your sound card.
You can listen to the CD by connecting an earphone to the earphone
connection terminal.
✱✱Manual Setup
1
2
Make the C:\SAMSUNG directory.
Playing DVDs or Video CDs
Set up and run the SOFT MPEG program supplied as an accessory.
Copy the files from the diskette to the C:\SAMSUNG directory.
To do so, type COPY A: * . * C:\SAMSUNG after the C:\prompt and press [Enter].
Storing and Cleaning Your Discs
3
4
5
Edit the CONFIG.SYS file.
Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000/V entry.
To ensure a long service life for your discs and drive, follow the pre-cautions
below when storing and cleaning your discs.
LAST DRIVE = Z
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1Do not place a disc in direct sunlight.
DEVICE = C :\SAMSUNG\SSCDROM.SYS/D : SSCD000/V
2Store a disc vertically in a well-ventilated and
Edit the AUTOEXEC.BAT file.
stable location.
Add the C:\SAMSUNG\MSCDEX/D:SSCD000 entry.
3Do not write or attach a label on a disc.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
C :\SAMSUNG\MSCDEX /D:SSCD000
4Do not drop a disc or place heavy objects on it.
5Do not touch the surface of a disc; hold it by
the edges.
Reboot the computer.
6To clean a disc, polish lightly from the inside
of the disc to the outside with a soft cotton cloth.
7Do not leave the disc compartment open
when you are not using it.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Recording Problems
If you have any problems recording via your COMBO drive,
follow the appropriate instructions below for the source that you are using.
✱✱Hard Drive
✱✱CD-ROM Drive
1
Check whether the source file is corrupted.
1
2
3
Clean the source CD, if necessary.
2 Optimize the hard disk by using the Windows defragmenter feature:
Create an image file and then copy the image file to the COMBO drive.
Check the CD-ROM drive record speed.
START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER
There are two recording methods :
Low-speed (file by file)
3 Decompress the hard disk if it is compressed.
High-speed (transfer of an image file from the hard disk)
4 Make sure that the space available on the hard disk is at least twice the
size of the largest file to be recorded on the disc.
4
If the transfer speed of the CD-ROM drive is slower than the record speed,
reduce the record speed.
5 If you wish to record more than 1000 small files:
First create an image file and copy the image file to the disc.
Choose the low record speed
Compress small files and then record them
Note
The COMBO Drive provide a high speed rewriting Disc recording function (CD-RW 10X).
To rewrite at a high speed, use the disc which High Speed is printed on.
HS-RW
: supporting 4X, 10X
General-RW : supporting 2X, 4X
✱✱Network Drive
1
Copy the network drive contents to the hard disk and then from the hard disk
to the COMBO drive.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution with errors
Term Description
Every CD-R or CD-RW drive records data by applying recording laser onto a CD.
If the CD is damaged or recording data is not possible, you need to remove the
following causes of the error before using the CD.
What is Buffer Under-Run?
Every CD-R or CD-RW drive records the data that the Host PC wants to record
until the data flow ends. However, if the buffer becomes empty temporarily,
this may cause errors in recording data.
It is recommended to set a CD-R or CD-RW drive as follows.
What is Auto-Run?
If inserting a CD into a drive, the operating system executes the Autorun.inf file
of the CD automatically.
1
2
3
Do not work on a multi-tasking environment and remove screen savers.
If you work on a multi-tasking environment while the CD-RW drive
is recording/deleting data, Buffer Under-Run may occur.
Do not allow any external access to the Host PC while recording data.
Recommended Disc Types
If another user accesses your printer through a network while you are
recording data, errors may occur.
CD-R
Ricoh, Taiyo Yuden, Samsung, Mitsui, SKC, CMC, Ritek, Kodak
Fujifilm, POSTECH
Remove the Auto-Run function of the CD.
If you insert a CD that has the Auto-Run function to a drive connected to a
PC while recording/deleting data, this may cause errors.
CD-RW Ricoh, Samsung, CMC, Ritek, SKC
How to cancel (select) the Auto-Run function
General DMA Installation Guide
Cancel (Select) the Auto-Run function in [Start > Setting > Control Panel >
System > Device Manager > CD-ROM Setting]
(Windows 95/98/Me)
Important!
4
Use image files when you record many small files.
Please read the entire DMA installation guide before installing your COMBO drive.
If you use a lot of small size files for recording, this may reduce the transaction
rate of the PC. Although Justlink function is often run, the recording quality
may become low.
About DMA Installation
For stable writing performance at high speeds, Installation of DMA transfer mode for
E-IDE/ATAPI interface is strongly recommended.
We recommend DMA mode for fast writing.
If you copy a CD from another, you do not require making available space in the
hard disk. However, when you use image files, you need to copy them on the hard
disk first and then copy to a CD. In this case, you need to ensure maximum 700MB
of available space in the hard disk for reliable recording process.
DMA Setting
Before you install your COMBO drive, we recommend to set DMA to enabled on your
PC system. See the following procedure to set DMA transfer mode in windows
oprerating system. (Windows 95 OSR2/98/ME)
Click on START
Click on Settings
Select Control Panel
Select the System Icon
Select the Device Manager panel
in System Properties
Expand the CD-ROM icon
5
6
Use an E-IDE cable, which has the specified length (46cm).
Select your CD-R/RW drive
Click on the Properties button
Click on the Settings tab
Check the DMA checkbox to enables DMA.
Click OK
Using E-IDE cables longer than 46cm may cause errors during data transaction.
Use only one recording software program.
To install a software program for recording, uninstall any other types or versions
of recording software programs first and then reboot the computer.
Restart your PC
Make sure you use the recording software CD (Nero Burning Rom /
Roxio Easy CD Creator) provided by us. Using our software program with
others may cause errors in recording.
Windows 2000/XP
Select the DMA mode by selecting [Start > Setting > Control Panel > System >
Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel
Advanced Information]
Not compatible with Windows 95 in case of Roxio Software.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Technical Problems
Problem
Meaning / Solution
Problem
Meaning / Solution
Check that the power, audio and IDE cables are
correctly connected to the computer.
Adjust the size of the replay screen.
The COMBO drive is not
detected by the computer.
When the MPEG software
plays a Video CD, the
pictures are not regular and
the running speed is too slow.
After checking the display resolution, adjust it,
if necessary.
Change the IDE cable and reconnect it to the
computer.
Preferably, connect a second IDE cable to the
COMBO drive in master mode.
After installing the COMBO
drive, the PC gets slower.
The computer may not recognize the disc if you
start playback too quickly after inserting the disc.
Open and close the disc compartment and try again.
The Disc is not in message is
displayed even though a disc
has been inserted.
Check the position of the jumper in the master/slave
select terminal.
Reinstall the device driver or update it with the
latest version by downloading it from the
Samsung Web site.
The COMBO drive is not
recognized by MS-DOS.
Clean the disc and try again.
The interface mode of the sound card is AT-BUS.
You must therefore connect the COMBO drive to
the IDE port on the PC mother board, rather than
to the sound card, or install an E-IDE compatible
sound card.
The COMBO drive is not
detected after it is connected
to a sound card.
This case may occur when there is a Windows
installation problem; reinstall Windows.
The COMBO drive is not
detected by Windows.
Check whether the audio cable is correctly
connected to the sound output terminal on the
COMBO drive and the sound card CD-IN terminal.
No sound is heard from an
audio CD.
Check that the sound card is operational.
Adjust the volume control.
Run the CD player supplied with Windows or your
sound card.
You can listen to the CD by connecting headphones
to the appropriate connector.
If you have installed the appropriate player, such as
Microsoft Windows Media Player, you can adjust the
volume using the headphone volume control on the
drive front panel.
If you select DIGITAL at CD Audio Play in Media
Player of Windows ME/XP, the earphone does not
appear in the Digital Mode.
Check whether the CD is of good quality and clean it,
if necessary.
A CD is not read or is read
too slowly.
Check that the power cable is correctly connected.
The disc compartment will
not open.
Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency
hole and push firmly until the disc compartment opens.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design specifications and these
user instructions are thus subject to change without notice.
ITEM
CD-RW
DVD / CD
DISC
Disc types supported DVD-ROM, DVD-VIDEO, DVD-R, DVD - RW, CD-DA (Audio),
in read mode
CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD
(Single, Multi-session), Video CD ready, Enhanced CD,
CD-I/FMV, CD-R, CD-RW, CD-TEXT
Erasing disc types
Disc diameter
CD-RW
120 mm or 80 mm
DRIVE
PERFORMANCE
Data transfer rate
Recording CD-R
600KB/sec ( 4X), 1200KB/sec ( 8X)
1800KB/sec (12X), 2400KB/sec (16X)
CD-RW
300KB/sec ( 2X), 600KB/sec ( 4X)
1500KB/sec (10X)
CD/CD-R CAV 40 Access Time
DVD CAV 12 Access Time
Reading
PIO Mode 4:16.6MB/sec
Multiword DMA mode 2:16.6MB/sec
Ultra DMA mode 2:33.3MB/sec
110ms (typical)
130ms/110ms (typical)
Access time (typical)
Data Buffer
8MB
Laser
Semiconductor laser
Stepping motor
Slide mechanism
Spindle motor
Load mechanism
Brushless motor
Tray. DC motor (Soft Eject). Horizontal/Vertical.
Mode 1: 1 block/1012, Mode 2: 1 block/109
Auto eject or Auto inject
ERROR RATE
Eject button
Indicator
FRONT PANEL
If the Power is ON/BUSY, this means the disc is loaded.
Green: Reading/Recording Status
Headphone output
Stereo mini-jack (Ø 3.6 mm) 0.6±20% (vrms) 33Ω
Dial type
Volume control
Required power
Interface connector
+5 VDC: 2.0A (max.), +12 VDC: 1.5 A (max.)
ATAPI (E-IDE)
REAR PANEL
Audio output
Jumper block
Operations
Storage
Line out 0.75±20% (vrms) : 47KΩ
Molex 70203 or other compatible models
Temperature: 0~50°C
Temperature: -25~55°C
Humidity: 10~80%
Humidity: 10~90%
OPERATING
ENVIRONMENT
Dimensions
Net weight
MTBF
148.2 (W) x 42 (H) x 184 (D) mm (including bezel)
770 g
GENERAL
RELIABILITY
125,000 POH(Duty 20%)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|