Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Country
Customer Care Centre
0818 717 100
0845 SAMSUNG (7267864)
Web Site
EIRE
U.K
Plasma TV
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
Model__________Serial No.___________
BN68-01416D-00
Download from Www.Somanuals.com. All Manuals Search And Download.
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
English - ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
General Information
Function Description
User Instructions............................................. 2
Checking Parts................................................ 4
Using the Stand-Base..................................... 4
Control Panel ................................................. 5
Connection Panel............................................ 6
Viewing the Remote Control ........................... 8
Time Features............................................... 25
Language / Melody / Light Effect /
Entertainment / Energy Saving ..................... 26
PC Display
Setting up Your PC Software
(Based on Windows XP)............................... 27
Input Mode (PC)............................................ 28
Setting the PC............................................... 29
Operation
Switching Your Television On and Off ............. 9
Viewing the Menus.......................................... 9
Plug & Play Feature...................................... 10
Using the TOOLS Button .............................. 12
Viewing External Signal Sources.................. 12
Editing Device Names................................... 13
Using the DTV Feature
Previewing the DTV Menu System ............... 30
Displaying Programme Information............... 31
Operating the DTV Menu.............................. 32
Channel Control
+
About Anynet
Storing Channels Automatically .................... 13
Storing Channels Manually........................... 14
Adding / Locking Channels ........................... 15
Sorting the Stored Channels......................... 16
Assigning Names to Channels...................... 16
Fine Tuning Channel Reception.................... 17
LNA (Low Noise Amplifier) ............................ 17
+
What is Anynet ?.......................................... 42
+
+
Connecting Anynet Devices........................ 42
Setting Up Anynet ....................................... 43
Scanning and Switching between Anynet
Devices ......................................................... 43
Recording...................................................... 44
Listening through a Receiver ........................ 45
Check Points before Requesting Service ..... 45
+
Picture Control
Changing the Picture Standard..................... 18
Customizing the Picture Settings.................. 18
Appendix
Configuring Detailed Settings on the Picture... 19
Teletext Feature (depending on the model).. 46
Wall Mount Kit Specifications (VESA)........... 48
Wall- mount adjustment (Sold separately) .... 49
How to assemble the Stand-Base
Picture Options ............................................. 20
Resetting the Picture Settings to the
Factory Defaults............................................ 22
(depending on the model)............................. 50
Troubleshooting ............................................ 51
Specifications................................................ 52
Sound Control
Sound Features ............................................ 23
Selecting the Sound Mode
(depending on the model)............................. 24
Connecting Headphones (Sold separately) .. 24
☛
➢
Symbols
Press
Important
Note
English - ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Cloth-Clean
Registration Card
Cover-Bottom / Screws (2ea)
(Refer to page 50)
Ferrite Core for Power Cord
Ferrite Core for S-Video
Sold Separately
Antenna Cable
Scart Cable
Component Cables
Audio Cables
PC Cable
PC Audio Cable
HDMI Cable
HDMI/DVI Cable
Ferrite Core (Power Cord, S-Video)
➢
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around
the cable near the plug.
Using the Stand-Base
Two or more people should carry
➢
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
Front (or Side) Panel
The product colour and shape may vary depending on the model.
➢
1
SOURCE
4
5
C/P.
Toggles between all the available input sources
(TV, Ext.1, Ext.ꢀ, AV, S-Video, Component,
PC, HDMI1, HDMIꢀ, HDMIꢁ and DTV).
Press to change channels. In the on-screen
menu, use the
would use the ▲ and ▼ buttons on the remote
control.
C/P.
buttons as you
In the on-screen menu, use this button as
you would use the ENTER button on the
remote control.
➢
Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
2
3
MENU
Press to see an on-screen menu of your TV’s
features.
6
7
POWER
Press to turn the TV on and off.
–
+
Remote Control Sensor
Aim the remote control towards this spot on the
TV.
Press to decrease or increase the volume. In
the on-screen menu, use the – + buttons
as you would use the ◄ and ► buttons on the
remote control.
8
Speakers
English - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Panel
Rear Panel
1
9
or
Cable Television
Network
or
2
3
4
5
6
7
8
The product colour and shape may vary depending on the model.
➢
Whenever you connect an audio or video system to your set, ensure that all elements are
☛
switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
1
2
POWER IN
Connect the supplied power cord.
5
6
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
COMPONENT IN
Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
Audio (AUDIO L/R) and video (Y/PB/PR) inputs
for Component.
7
SERVICE
3
4
PC IN(PC) / (AUDIO)
Connect to the video and audio output jack on
your PC.
−
−
Connector for service.
Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
EXT 1, EXT ꢀ
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Input
Output
Connector
Video Audio(L/R) RGB Video + Audio(L/R)
Only TV or DTV
EXT 1
EXT 2
✔
✔
✔
output is available.
Output you can
choose.
✔
✔
Continued...
English - ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI IN AUDIO L/R
DVI audio outputs for external devices.
8
HDMI IN 1,ꢀ
-
No additional Audio connection is needed
for an HDMI to HDMI connection.
When using an HDMI/DVI cable connection,
you must use the HDMI IN 2 jack.
What is HDMI?
- “High Definition Multimedia interface”
allows the ansmission of high definition
digital video data and multiple channels
of digital audio.
9
DVI IN (HDMI ꢀ) AUDIO R/L
75Ω Coaxial connector for Aerial/Cable
Network.
-
➢
Supported modes for HDMI/DVI and Component
480i 480p 576i 576p 720p 1080i
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
X
X
O
X
O
O
X
X
O
O
X
O
O
O
O
O
O
O
- The HDMI/DVI terminal supports DVI
connection to an extended device with
the appropriate cable (not supplied). The
difference between HDMI and DVI is that
the HDMI device is smaller in size, has
the HDCP (High Bandwidth Digital Copy
Protection) coding feature installed, and
supports multi - channel digital audio.
Side Panel
1
2
3
or
4
The product colour and shape may vary depending on the model.
➢
1
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 40)
2
3
4
HDMI IN ꢁ
Connect to the HDMI jack of a device with
HDMI output.
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for
external devices, such as a camcorder or VCR.
− When not inserting “CI CARD” in some
channels, “Scramble Signal” is displayed on
the screen.
− The pairing information containing a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has finished, the message “Updating
Completed” is displayed, indicating that the
channel list is now updated.
Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
➢
Insert the CI-Card in the direction marked
on it.
➢
English - ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the Remote Control
The performance of the remote control may be affected by bright light.
1
2
3
4
POWER button
(turns the TV on and off)
Selects the TV and DTV
mode directly
Number buttons for direct
channel access
One/Two-digit channel
selection
Temporary sound switch-off
Volume increase
Volume decrease
Electronic Program Guide
(EPG) display
Use to quickly select
frequently used functions.
Control the cursor in the
menu
Use to see information on
the current broadcast
Press to select the optional
display and sound modes for
sports, cinema and games.
c
Use this when connecting
a SAMSUNG DMA (Digital
Media Adapter) device through
an HDMI interface and
switching to DMA mode.(The
DMA button is optional.)
For more information on the
operating procedures, refer
to the user manual of the
DMA. This button is available
when “Anynet+(HDMI-CEC)"
is “On” (see page 43)
TV/DTV
5
6
- --
/
7
8
9
0
#
d
e
Digital subtitle display
Selects the HDMI mode
directly
P
GUIDE
MENU
Teletext Functions
(Refer to page 46)
2
Exit from the teletext display
(depending on the model)
Teletext store
Teletext size
Teletext reveal
Fastext topic selection
Teletext display/mix both
teletext information and the
normal broadcast
Teletext mode selection
(LIST/FLOF)
$
VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
Available source selection
Previous channel
Next channel
Previous channel
Displays the main on-screen
menu
Channel control button
(Refer to page 15)
7
8
0
!
@
TTX/MIX
E.MODE
P.SIZE
HDMI
DMA
%
^
&
SUBT.
*
(
)
%
Returns to the previous
menu
Exit the on-screen menu
Picture size selection
^
&
Teletext sub page
P
P
:Teletext next page
:Teletext previous page
a
b
*
)
a
Teletext index
Teletext hold
Teletext cancel
Continued...
English - ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Batteries in the Remote Control
1
ꢀ
Lift the cover at the back of the remote control upward as
shown in the figure.
Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and
manganese.
➢
ꢁ
Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
➢
place if you won’t be using the remote control for a long time. The remote control can be used up
to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
➢
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1
Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
➢
ꢀ
Press the
(Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is re-selected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
➢
ꢁ
4
To switch the television off, press the
the POWER button on the remote control.
(Power) button (On/Off) on the front of the television or press
To switch the TV on, press the
(Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
Viewing the Menus
T V
Picture
: Standard
1
Press the MENU button.
Mode
►
ꢃ
The main menu is displayed on the screen.
Its left side has six icons: Picture, Sound, Channel, Setup,
Input, and Digital Menu.
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢅ5
45
50
50
R50
►
Tint
G50
ꢀ
ꢁ
4
5
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
Detailed Settings
Picture Options
Reset
►
►
: OK
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
Move
Enter
Exit
Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
Press the EXIT button to exit from the menu.
English - ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
Plug & Play
Start Plug & Play.
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed.
☛
OK
Enter
Any functions related to Digital TV (DVB) will only work in
☛
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some
countries.
Plug & Play
English
Deutsch
Français
Italiano
▼
Language
Move
Enter
1
If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER button.
Plug & Play
Select ‘Home Use’
when installing this TV in your home.
ꢀ
ꢁ
The Language menu will automatically appear after several
seconds.
Store Demo
Home Use
Select the appropriate language by pressing the ▲ or ▼
button.
Move
Enter
Press the ENTER button. The message Select ‘Home Use’
when installing this TV in your home. is displayed.
Plug & Play
4
Press the ◄ or ► button to select Store Demo or Home Use,
then press the ENTER button. The message to check the
connected status of the antenna is displayed.
Check antenna input.
OK
The default selection is Home Use.
We recommend setting the TV to Home Use mode for the
best picture in your home environment.
Store Demo mode is only intended for use in retail
Enter
➢
➢
Plug & Play
➢
▲
environments.
Country
Move
United Kingdom
Austria
Eastern Europe
Others
If the unit is accidentally set to Store Demo mode and you
➢
want to return to Home Use (Standard): Press the Volume
button. When the volume OSD is displayed, press and
hold the MENU button for 5 seconds.
Enter
5
ꢂ
Make sure that the antenna is connected to the TV.
Press the ENTER button. The Country menu is displayed.
Plug & Play
Some DTV functions may not be available.
Digital Scan?
Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER button.
The message Some DTV functions may not be available.
Digital Scan? is displayed.
Yes
No
Move
Enter
Skip
This function is supported for all countries except
➢
for the following countries: France, Germany, Italy,
Netherlands, Spain, Switzerland, United Kingdom,
Austria.
Plug & Play
P
1
C
--
40 MHz
0 %
If your country supports the DTV functions, the message is
not displayed. Then you can follow the instructions from step
1ꢀ. When the local service provider does not support DTV
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
properly.When No is selected, follow the instructions from step
ꢃ to 10. When Yes is selected, follow the instructions from
step 11.
Start
Enter
Skip
Continued...
English - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ
ꢄ
Select No pressing the ◄ or ► button, then press the ENTER
button. Auto Store menu is displayed.
Plug & Play
Year Hour
Clock Set
Month
Day
01
Minute
04
▲
Press the ENTER button to start search the channels.
The channel search will start and end automatically. After
all the available channels are stored, Clock Set menu is
automatically displayed. Press the ENTER button.
01
ꢀ00ꢄ
00
:
▼
Move
Adjust
Enter
To stop the search before it has finished, press the
ENTER button with Stop selected.
➢
Plug & Play
ꢅ
Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
0%
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
Services found: 0
Enter
Channel:
Start
Skip
-
➢
10 Press the ENTER button to confirm your setting. The
message Enjoy your viewing is displayed. When you have
finished, press the ENTER button.
Plug & Play
Even if the ENTER button is not pressed, the message
will automatically disappear after several seconds.
➢
Scanning for digital services...
ꢀꢅ%
11 Select Yes pressing the ◄ or ► button, then press the
Services found: ꢂ
Enter
Channel: ꢁ5
Stop
ENTER button. Auto Store menu is displayed.
1ꢀ Press the ENTER button to start search the analog channels.
The analog channel search will start and end automatically.
After all the available analog channels are stored, the screen
for searching digital channels is automatically displayed.
Skip
Plug & Play
To stop the search before it has finished, press the
ENTER button with Stop selected.
➢
The Iberian Peninsula and Balearic Islands
Canary Islands
1ꢁ Press the ENTER button to start search the digital channels.
The digital channel search will start and end automatically.
After all the available digital channels are stored, the screen
to select a time zone is displayed depending on the country.
Move
Select
Skip
To stop the search before it has finished, press the
ENTER button with Stop selected.
➢
<Spain Only>
If the DTV channel is updated, the Source in the source
list of the Input menu is automatically changed to DTV.
➢
Plug & Play
For detailed descriptions about DTV channel update,
refer to page 32 of this manual.
➢
Set the current time.
Month Day
Year
ꢀ00ꢄ
▲
14 Press the ▲ or ▼ button to select required time zone, then
press the ENTER button. The screen for setting the time is
displayed. Press the ENTER button.
01
15
▼
Hour
00
Min
00
15 Press the ◄ or ► button to select Month, Day, Year, Hour,
Adjust
Move
Enter
Skip
or Min. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Min directly
by pressing the numeric buttons on the remote control.
➢
Enjoy your viewing
OK
1ꢂ Press the ENTER button to confirm your setting. The
message Enjoy your viewing is displayed. When you have
finished, press the ENTER button.
Even if the ENTER button is not pressed, the message
will automatically disappear after several seconds.
➢
T V
Setup
Plug & Play
►
Language
: English
: In Watching TV
►
►
►
►
►
►
►
If you want to reset this feature …
Time
Light Effect
Wall-Mount Adjustment
Melody
1
ꢀ
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
: Off
Entertainment
Energy Saving
:
Off
Off
:
ꢁ
Press the ENTER button again to select Plug & Play.
The message Start Plug & Play is displayed.
Move
Enter
Return
English - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The
“Tools” menu changes depending on which external input mode you are viewing.
1
ꢀ
ꢁ
Press the TOOLS button.
The Tools menu will appear.
Tools
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
:
:
:
:
:
:
Standard
Custom
Off
Off
Off
Press the ▲ or ▼ button to select a menu, then press the
ENTER button.
Press the ▲/▼/◄/►/ENTER buttons to display, change, or
use the selected items.
Mono
Move
Enter
Exit
For a more detailed description of each function, refer to the
corresponding page.
+
• Anynet (HDMI-CEC), see page 43
• Picture Mode, see page 18
• Sound Mode, see page 23
• Sleep Timer, see page 25
• SRS TS XT, see page 23
• Energy Saving, see page 27
• Dual I-II, see page 24
Viewing External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
T V
Input
: TV
Source List
Edit Name
►
►
+
Anynet (HDMI-CEC)
1
ꢀ
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
ꢁ
4
Press the ENTER button again to select Source List.
Move
Enter
Return
Press the ▲ or ▼ button to select the signal source, then
press the ENTER button.
Available signal sources: TV, Ext.1, Ext.ꢀ, AV, S-Video,
Component, PC, HDMI1, HDMIꢀ, HDMIꢁ, DTV
T V
Source List
TV
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
DTV
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
You can choose only those external devices that are connected
to the TV.
➢
➢
➢
➢
Move
Enter
Return
You can select these options simply by pressing the SOURCE
button on the remote control.
To watch television programme again, press the TV/DTV button
and select the channel number required.
You can also watch HDMI mode simply by pressing the HDMI
button on the remote control.
English - 1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing Device Names
You can give a name to the external source.
Input
: TV
T V
Source List
Edit Name
►
►
1
ꢀ
Press the MENU button to display the menu.
+
Anynet (HDMI-CEC)
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
ꢁ
4
5
Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
Move
Enter
Return
T V
Edit Name
: −
Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names: VCR, DVD, Cable STB, Satellite
STB, PVR STB, AV Receiver, Game, Camcorder, PC, TV,
IPTV, Blu-Ray, HD DVD, DMA.
----
VCR
DVD
Ext.1
Ext.ꢀ
AV
S-Video
Component
PC
HDMI1
HDMIꢀ
HDMIꢁ
: −
:
:
Cable STB
: −Satellite STB
: −PVR STB
:
:
:
AV Receiver
Game
▼
ꢂ
Press the EXIT button to exit.
Move
Enter
Return
Storing Channels Automatically
Not available in DTV or external input mode.
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any
channels you do not wish to watch.
T V
Channel
➢
Belgium
France
Germany
Italy
Netherlands
Spain
Country
:
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
Switzerland
United Kingdom
▼
:
1
ꢀ
Press the MENU button to display the menu.
Move
Enter
Return
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
T V
Channel
:
Country
Auto Store
Manual Store
Channel Manager
Sort
Name
United Kingdom
►
►
►
►
►
►
►
►
ꢁ
4
Press the ENTER button again. The available countries are
listed.
Select your country by pressing the ▲ or ▼ button, then press
the ENTER button.
Fine Tune
LNA
: Off
Even though you have changed the country setting in this
➢
menu, the country setting for DTV is not changed. Use
the Plug & Play function to change the country setting for
DTV. (Refer to pages 10 to 11)
Move
Enter
Return
Auto Store
5
ꢂ
Press the ▲ or ▼ button to select Auto Store, then press the
ENTER button.
P
1
C
--
40 MHz
0 %
Press the ENTER button again to start the search.
The search will end automatically.
Start
To stop the search before it has finished, press the MENU
or the ENTER button.
Enter
Return
➢
English - 1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Channels Manually
Not available in DTV or external input mode.
You can store television channels, including those received
via cable networks.
T V
Channel
➢
Country
:
United Kingdom
►
►
►
►
►
►
►
►
Auto Store
Manual Store
Channel Manager
Sort
When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you
wish to identify.
Name
Fine Tune
LNA
: Off
1
ꢀ
Press the MENU button to display the menu.
Move
Enter
Return
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
T V
Manual Store
: P
Programme
Colour System
Sound System
Channel
Search
Store
1
: Auto
: BG
: C --
: 40
►
►
ꢁ
4
5
Press the ▲ or ▼ button to select Manual Store, then press
the ENTER button.
MHz
: ?
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Move
Enter
Return
ꢂ
Press the EXIT button to exit.
Programme (Programme number to be assigned to a channel)
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
Colour System: Auto/PAL/SECAM/NTSC4.4ꢁ
➢
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
Search (When you do not know the channel numbers)
➢
➢
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER button.
Channel mode
☛
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding / Locking Channels
Not available in DTV or external input mode.
Using the Channel Manager, you can conveniently lock or add
channels.
T V
Channel
➢
Country
:
United Kingdom
►
►
►
►
►
►
►
►
Auto Store
Manual Store
Channel Manager
Sort
1
ꢀ
Press the MENU button to display the menu.
Name
Fine Tune
LNA
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
: Off
ꢁ
Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER button.
Move
Enter
Return
T V
Channel Manager
Channel List
Child Lock
Adding channels
Using the Channel List, you can add channels.
►
►
: Off
4
5
Select Channel List by pressing the ENTER button.
Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER button to
add the channel.
If you press the ENTER button again, the ( ) symbol
next to the channel disappears and the channel is not
added.
➢
Move
Enter
Return
1 / 10
Channel List
P
1
C ꢂ
Locking channels
Prog.
This feature allows you to prevent unauthorized users, such as
children, from watching unsuitable programmes by muting out
video and audio.
▲
0
1
ꢀ
ꢁ
4
5
ꢂ
ꢃ
ꢄ
ꢅ
C 1
C --
C --
C --
C --
C --
C --
C --
C --
C --
ꢂ
ꢃ
ꢄ
ꢅ
Press the ▲ or ▼ button to select Child Lock, then press the
ENTER button.
Select On by pressing the ▲ or ▼ button, then press the
ENTER button.
▼
Add
Lock
Move
Page
Enter
Return
Press the ▲ or ▼ button to select Channel List, then press
the ENTER button.
Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a channel to be locked, and press
the ENTER button.
If you press the ENTER button again, the ( ) symbol next to the channel disappears and the
channel lock is canceled.
➢
A blue screen is displayed when Child Lock is activated.
➢
10 Press the EXIT button to exit.
You can select these options simply by pressing the CH LIST
button on the remote control.
➢
English - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Sorting the Stored Channels
Not available in DTV or external input mode.
This operation allows you to change the programme numbers
of the stored channels.
T V
Channel
➢
Country
:
United Kingdom
►
►
►
►
►
►
►
►
Auto Store
Manual Store
Channel Manager
Sort
This operation may be necessary after using the auto store.
1
ꢀ
Press the MENU button to display the menu.
Name
Fine Tune
LNA
: Off
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Move
Enter
Return
ꢁ
4
5
Press the ▲ or ▼ button to select Sort, then press the ENTER
button.
T V
Sort
Prog.
Ch.
▲
Name
Select the channel that you wish to move by pressing the ▲ or
▼ button, then press the ENTER button.
0
1
2
3
4
5
ꢂ
ꢃ
ꢄ
ꢅ
C01
C- -
C- -
C- -
C- -
C- -
C- -
C- -
C- -
C- -
▼
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
►
Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER button. The channel is moved to its new
position and all other channels are shifted accordingly.
Move
Enter
Return
ꢂ
ꢃ
Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
Press the EXIT button to exit.
Assigning Names to Channels
Not available in DTV or external input mode.
T V
Channel
:
➢
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
Country
Auto Store
Manual Store
United Kingdom
►
►
►
►
►
►
►
►
Channel Manager
Sort
1
ꢀ
Press the MENU button to display the menu.
Name
Fine Tune
LNA
: Off
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Move
Enter
Return
ꢁ
4
5
Press the ▲ or ▼ button to select Name, then press the
ENTER button.
T V
Name
Name
Prog.
Ch.
▲
Press the ▲ or ▼ button to select the channel to be assigned
to a new name, then press the ENTER button.
0
1
ꢀ
ꢁ
4
5
ꢂ
ꢃ
ꢄ
ꢅ
C01
C- -
C- -
C- -
C- -
C- -
C- -
C- -
C- -
C- -
▼
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER button.
Move
Enter
Return
ꢂ
ꢃ
Repeat steps 4 to 5 for each channel to be assigned to a new
name.
Press the EXIT button to exit.
English - 1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine Tuning Channel Reception
Not available in DTV or external input mode.
T V
Channel
➢
If the reception is clear, you do not have to fine tune the
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
Country
:
United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
1
ꢀ
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
Move
Enter
Return
ENTER button.
Fine Tune
ꢁ
4
Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER button.
P
1
0
To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER button.
Reset
Save
Adjust
Return
Press the INFO button. Fine Tune Store will change the
colour of the Channel OSD (On Screen Display) from
White to Red and add the “*” mark.
➢
P
1 *
Mono
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER button.
➢
Picture
: Standard
: Custom
: Off
Sound
5
Press the EXIT button to exit.
SRS TS XT
:
−− −−
LNA (Low Noise Amplifier)
This function is very useful in the situation that the TV is used
in weak signal.
LNA amplifies the TV signal in the weak signal area, a low-
noise preamplifier boosts the incoming signal.
T V
Channel
Country
:
United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
1
ꢀ
Press the MENU button to display the menu.
Name
Fine Tune
LNA
Press the ▲ or ▼ button to select Channel, then press the
: Off
ENTER button.
Move
Enter
Return
ꢁ
Press the ▲ or ▼ button to select LNA, then press the ENTER
button.
4
5
Select Off or On by pressing the ▲ or ▼ button, then press the ENTER button.
Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as On or Off.
➢
English - 1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
T V
Picture
: Standard
Mode
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢃ
ꢅ0
45
50
50
R50
1
ꢀ
ꢁ
4
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Tint
G50
Detailed Settings
Picture Options
Reset
: OK
Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Move
Enter
Return
Available modes: Dynamic, Standard, Movie
T V
Picture
The settings values may vary depending on the input
source.
➢
Mode
:
Dynamic
Standard
Movie
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢃ
ꢅ0
45
5
Press the EXIT button to exit.
Choose Dynamic for viewing the TV during the day or
when there is bright light in the room.
Choose Standard for general TV watching mode.
50
50
R50
Tint
G50
➢
Detailed Settings
Picture Options
Reset
: OK
Choose Movie when viewing the movie.
Move
Enter
Return
Easy Setting
Tools
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
1
ꢀ
ꢁ
Press the TOOLS button on the remote control.
◄
:
:
Standard
Custom
Off
►
Press the ▲ or ▼ button to select Picture Mode.
:
:
Off
Off
Press the ◄ or ► button to select the required option.
:
Mono
Move
Exit
Adjust
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
T V
Picture
Mode
: Standard
ꢃ
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢅ0
45
50
50
R50
1
ꢀ
ꢁ
4
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Tint
G50
Detailed Settings
Picture Options
Reset
: OK
Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Move
Enter
Return
Available modes: Dynamic, Standard, Movie
5
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
When you are satisfied with your setting, press the ENTER button.
Press the EXIT button to exit.
ꢂ
ꢃ
Cell Light - Contrast – Brightness – Sharpness – Colour – Tint
In Analog TV, Ext., AV, S-Video modes of the PAL system, you cannot use the Tint Function.
In PC mode, you can only make changes to Cell Light, Contrast, and Brightness.
Press the ◄ or ► button until you reach the optimal setting.
➢
➢
English - 1ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Detailed Settings on the Picture
You can set detailed picture settings.
T V
Picture
: Standard
Mode
1
ꢀ
ꢁ
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER button.
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢃ
ꢅ0
45
50
50
R50
Tint
G50
Detailed Settings
Picture Options
Reset
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
: OK
Available options: Black Adjust, Dynamic Contrast,
Gamma, Colour Space, White Balance, Flesh Tone, Edge
Enhancement
When you are satisfied with your setting, press the ENTER
button.
Move
Enter
Return
T V
Detailed Settings
5
ꢂ
Black Adjust
Dynamic Contrast : Medium
Gamma
Colour Space
White Balance
Flesh Tone
: Off
Press the EXIT button to exit.
:
0
: Auto
Detailed Settings is available in Standard or Movie mode.
➢
➢
:
0
Edge Enhancement : On
In PC mode, you can only make changes to Dynamic
Contrast, Gamma and White Balance from among the
Detailed Settings items.
Move
Enter
Return
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -ꢁ ~ +ꢁ
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
Colour Space: Auto/Native/Custom
Colour space is a colour matrix composed of red, green and blue colours.
Select your favorite colour space to experience the most natural colour.
− Auto: Auto Colour Space automatically adjusts to the most natural colour tone based on program
sources.
− Native: Native Colour Space offers deep and rich colour tone.
− Custom: Adjusts the colour range to suit your preference. (see “Customizing the Colour Space”)
Customizing the Colour Space
Colour: Red/Green/Blue/Yellow/Cyan/Magenta
Adjusts the Colour range to suit your preference.
Colour is available when Colour Space is set to Custom.
Press the ▲ or ▼ button to select Red, Green, Blue, Yellow, Cyan or Magenta.
Press the ENTER button.
− Red/Green/Blue: In Colour, you can adjust the RGB values for the selected colour.
Press the ▲ or ▼ button to select Red, Green or Blue to change it. Press the ENTER button.
Press the ◄ or ► button to decrease or increase the value of a particular item.
Press the ENTER button.
− Reset: Resets the colour space to the default values.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the color temperature for more natural picture colors.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone:-15~+15
You can emphasize the pink tone in the picture.
Press the ◄ or ► button until you reach the optimal setting.
Changing the adjustment value will refresh the adjusted screen.
➢
Edge Enhancement: Off/On
You can emphasize object boundaries.
English - 1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Options
You can set detailed picture settings.
T V
T V
T V
Picture
: Standard
Mode
1
ꢀ
ꢁ
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Picture Options, then press
the ENTER button.
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢃ
ꢅ0
45
50
50
R50
Tint
G50
Detailed Settings
Picture Options
Reset
4
5
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
: OK
Move
Enter
Return
Picture Options
Colour Tone : Normal
ꢂ
Press the EXIT button to exit.
In PC mode, you can only make changes to the Color Tone,
Size and Screen Burn Protection from among the items in
Picture Options.
➢
Size
Screen Mode
Digital NR
: Auto Wide
: 1ꢂ:ꢅ
: Auto
Real 100 Hz Demo : Off
DNle : Off
HDMI Black Level : Normal
Colour Tone: Coolꢀ/Cool1/Normal/Warm1/Warmꢀ
Blue only mode
: Off
When the picture mode is set to Dynamic or Standard,
Warm1 and Warmꢀ cannot be selected.
➢
Screen Burn Protection
Size: Auto Wide/1ꢂ:ꢅ/Wide Zoom/Zoom/4:ꢁ/Just Scan
Move
Enter
Size
Return
You can select the picture size which best corresponds to your
viewing requirements.
− Auto Wide: Expanding and pulling up the picture from 4:3 to
Auto Wide
1ꢂ:ꢅ
16:9 ratio.
Wide Zoom
Zoom
− 1ꢂ:ꢅ: Sets the picture to 16:9 wide mode.
4:ꢁ
− Wide Zoom: Magnify the size of the picture more than 4:3.
Just Scan
Move the screen up/down using the ▲ or ▼ button after
selecting the
by pressing the ► or ENTER button.
− Zoom: Magnify the size of the picture vertically on screen.
Move
Enter
Return
− 4:ꢁ: Sets the picture to 4:ꢁ normal mode.
− Just Scan: Use the function to see the full image without any
cutoff when HDMI (720p/1080i), Component (1080i) or DTV
(1080i) signals are input.
After selecting Just Scan in HDMI (10ꢄ0i) or Component
(10ꢄ0i) mode:
Press the ◄ or ► button to select
, then press the ENTER button.
Press the ▲, ▼, ◄ or ► button to move the picture up, down, left and right.
Reset: Press the ◄ or ► button to select Reset, then press the ENTER button. You can initialize
the setting.
With the HDMI Just Scan picture size, depending on the AV devices, the screen may be cut off
or a specific colour appears on the screen.
➢
For an HDMI (1080p) connection of 24, 25, 30, 50, and 60 Hz, and for a Component (1080p)
➢
connection of 50 and 60Hz, only the input source is supported.
You can change the picture size simply by pressing the P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
➢
➢
➢
➢
➢
The items available may differ depending on the selected mode.
Auto Wide function is available only in TV, DTV, Ext.1, Ext.ꢀ, AV, and S-Video mode.
Settings can be adjusted and stored for each external device you have connected to an input of the
TV.
In PC Mode, only “16:9” and “4:3” mode can be adjusted.
➢
Positioning and Sizing the screen using Zoom
Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
Move the screen up/down using the ▲ or ▼ button after selecting the
by pressing the ◄ or ►
button.
Resize the screen vertically using the ▲ or ▼ button after selecting the
button.
by pressing the ◄ or ►
Continued...
English - ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
T V
Picture Options
Screen Mode: 1ꢂ:ꢅ/Wide Zoom/Zoom/4:ꢁ
Colour Tone
: Normal
When setting the picture size to Auto Wide in a 16:9 wide TV,
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this function
is intended for users to select it.
Size
: Auto Wide
Screen Mode
Digital NR
Real 100 Hz Demo :
:
:
1ꢂ:ꢅ
Wide Zoom
Zoom
DNle
:
:
4:ꢁ
HDMI Black Level
Blue only mode
Screen Burn Protection
: Off
− 1ꢂ:ꢅ: Sets the picture to 16:9 wide mode.
− Wide Zoom: Magnify the size of the picture more than 4:3.
− Zoom: Magnify the size of the picture vertically on screen.
− 4:ꢁ: Sets the picture to 4:ꢁ normal mode.
Move
Enter
Return
This function is available in Auto Wide mode.
This function is not available in Component or HDMI mode.
Digital NR: Off/Low/Medium/High/Auto
➢
➢
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
Real 100 Hz Demo: Off/On
➢
You can get a clear distinction between “Real 100Hz” and 50Hz, especially when watching sports.
Therefore, when seeing a paused or static image, you will not be able to distinguish between “Real
100Hz” and 50Hz.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast
enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer,
more detailed image to you. DNIeTM technology will fit every signal into your eyes.
➢
This cofunction is not available in PC mode.
DNIe is only available in Dynamic mode.
HDMI Black Level: Normal/Low
➢
➢
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low color, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the externel input connects to HDMI(RGB signals).
Blue Only Mode: Off/On
➢
This function is for AV device measurement experts. This function displays the blue signal only by
removing the red and green signals from the video signal so as to provide a Blue Filter effect that is
used to adjust the Colour and Tint of video equipment such as DVD players, Home Theaters, etc.
Using this function, you can adjust the Colour and Tint to
T V
Picture Options
preferred values appropriate to the signal level of each video
device using the Red/Green/Blue/Cyan/Magenta/Yellow Colour
Bar Patterns, without using an additional Blue Filter.
Colour Tone
Size
: Normal
: Auto Wide
: 1ꢂ:ꢅ
Screen Mode
Digital NR
Real 100 Hz Demo : Off
DNle : On
HDMI Black Level : Normal
: Auto
Blue Only Mode is available when the picture mode is set
➢
to Movie or Standard.
Screen Burn Protection
Blue only mode
Screen Burn Protection
: Off
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in
minutes.
− Pixel Shift: Using this function, you can minutely move
pixels on the PDP in horizontal or vertical direction to
minimize after image on the screen.
Move
Enter
Return
T V
Screen Burn Protection
Pixel Shift
White
Scrolling
Side Gray
: Dark
• Set Pixel Shift to On by pressing the ▲ or ▼ button, then
press the ENTER button.
• Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Move
Enter
Return
Available options: Horizontal Dot, Vertical Line, Time
Continued...
English - ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
T V
Pixel Shift
: On
Optimum condition for pixel shift;
➢
➢
Pixel Shift
Horizontal Dot
Vertical Line
Time
: ꢀ
TV/Ext/AV/Component/
PC
: ꢀ
HDMI/DTV
: ꢀ min
Horizontal Dot
Vertical Line
Time (minute)
1
1
2
2
2
2 min
Move
Enter
Return
The Pixel Shift value may differ depending on the monitor
size (inches) and mode.
− White: This function helps remove after images on the screen by changing the colour of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
− Scrolling: This function helps remove after images on the screen by moving all the pixels on the
PDP according to a pattern. Use this function when there are remaining after images or symbols on
the screen especially when you displayed a still image on the screen for a long time.
− Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either White or Scrolling function. Although both of
the two functions remove after images on the screen, Scrolling is more effective.
➢
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution
of the function, repeat the function again.
➢
Press any button on the remote control to cancel this feature.
➢
Resetting the Picture Settings to the Factory Defaults
You can set detailed picture settings.
T V
Picture
: Standard
Mode
Cell Light
Contrast
Brightness
Sharpness
Colour
ꢃ
ꢅ0
1
ꢀ
ꢁ
Press the MENU button to display the menu.
45
50
Press the ENTER button to select Picture.
50
Tint
G50
R50
Press the ▲ or ▼ button to select Reset, then press the
ENTER button.
Detailed Settings
Picture Options
Reset
: O
OK
Cancel
4
Press the ▲ or ▼ button to select OK or Cancel then press
the ENTER button.
Move
Enter
Return
Each mode can be reset.
➢
English - ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Features
T V
Sound
: Custom
1
ꢀ
Press the MENU button to display the menu.
Mode
Press the ▲ or ▼ button to select Sound, then press the
ENTER button.
Equalizer
SRS TS XT
Auto Volume
TV Speaker
: Off
: Off
: Off
ꢁ
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Mode, Equalizer, SRS TS XT, Auto
Volume, TV Speaker
Move
Enter
Return
When you are satisfied with your setting, press the ENTER
button.
T V
Equalizer
5
Press the EXIT button to exit.
Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used
when watching a given broadcast.
R
+
+
0
-
0
-
L
Easy Setting
Balance
100Hz ꢁ00Hz 1kHz ꢁkHz 10kHz
1 Press the TOOLS button on the remote control.
ꢀ Press the ▲ or ▼ button to select Sound Mode.
ꢁ Press the ◄ or ► button to select the required option.
Move
Adjust
Return
Tools
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
Equalizer: Balance/100Hz/ꢁ00Hz/1kHz/ꢁkHz/10kHz
The television has several settings which allow you to control
the sound quality.
:
◄
:
Standard
Custom
Off
►
SRS TS XT
Energy Saving
Dual I-II
:
Off
:
:
Off
Mono
If you make any changes to these settings, the sound
mode is automatically switched to Custom.
➢
Move
Exit
Adjust
SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound experience through any two-speaker
playback system, including internal television speakers. It is fully compatible with all multichannel
formats.
TruSurround XT, SRS and
Symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Tools
Easy Setting
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
:
:
:
◄
:
:
Standard
Custom
Off
Off
Off
1 Press the TOOLS button on the remote control.
ꢀ Press the ▲ or ▼ button to select SRS TS XT.
ꢁ Press the ◄ or ► button to select Off or On.
►
Mono
Move
Exit
Adjust
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume
every time the channel is changed. This feature lets you automatically adjust the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
TV Speaker: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The
+,
- and MUTE buttons do not operate when the TV Speaker is set to Off.
➢
➢
When TV Speaker is set to Off, the Sound menus cannot be adjusted.
English - ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and output of the audio signal. When power
is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the
current transmission.
Easy Setting
Tools
Anynet+ (HDMI-CEC)
1
ꢀ
ꢁ
Press the TOOLS button on the remote control.
Press the ▲ or ▼ button to select Dual I-II.
Press the ◄ or ► button to select the required option.
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
:
:
:
Standard
Custom
Off
:
:
Off
Off
◄
Mono
►
Move
Exit
Adjust
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Mono
(Normal)
Regular + NICAM Mono
NICAM
NICAM
NICAM
stereo
Mono
(Normal)
NICAM Stereo
Stereo
NICAM
dual-1
NICAM
dual-ꢀ
Mono
(Normal)
NICAM DUAL-I/II
Regular broadcast
(Standard audio)
Mono (Normal use)
A2
Stereo
Bilingual or DUAL-I/II
Dual I
Stereo
Dual II
Mono
(Forced mono)
Stereo
If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
If the stereo signal is weak and automatic switching occurs, switch to Mono.
This function is only available in Analog TV mode.
➢
Connecting Headphones (Sold separately)
You can connect a set of headphones to your set if you wish to watch a TV program
without disturbing other people in the room.
TV Side Panel
When you insert the head set jack into the corresponding
port, you can operate only “Auto Volume” in Sound menu.
➢
Prolonged use of headphones at a high volume may
damage your hearing.
➢
You will not hear sound from the speakers when you connect
headphones to the TV.
➢
The headphone volume and TV volume are adjusted
separately.
➢
15
English - ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Features
T V
T V
T V
Setup
: English
In Watching TV
1
ꢀ
Press the MENU button to display the menu.
Plug & Play
Language
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Time
Light Effect
Wall-Mount Adjustment
Melody
Entertainment
Energy Saving
:
: Off
: Off
: Off
ꢁ
4
Press the ▲ or ▼ button to select Time, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Clock Set, Sleep Timer, Timer 1, Timer ꢀ,
Timer ꢁ
Move
Enter
Return
Time
Clock Set
Sleep Timer
Timer 1
Timer ꢀ
Timer ꢁ
: 00 : 00
: Off
: Off
: Off
: Off
5
When you are satisfied with your setting, press the ENTER
button.
ꢂ
Press the EXIT button to exit.
Clock Set
You can set the television clock so that the current time is
displayed when pressing the INFO button on the remote
control. You must also set the time if you wish to use the
automatic on or off timers.
− Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
Move
Enter
Return
Timer 1
On Time
:
:
00
00
00
Off
Off
Off Time
00
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
➢
Repeat
Once
Volume
10
In the event of a power interruption or the set being turned
off at the supply, the settings for the Clock will be lost.
➢
Move
Adjust
Return
Sleep Timer
You can select a time period of between 30 and 180 minutes
after which the television automatically switches to standby
mode.
− Select the preset time interval (Off, ꢁ0, ꢂ0, ꢅ0, 1ꢀ0, 150, or
1ꢄ0) for staying on by pressing the ▲ or ▼ button.
Easy Setting
Tools
1 Press the TOOLS button on the remote control.
ꢀ Press the ▲ or ▼ button to select Sleep Timer.
ꢁ Press the ◄ or ► button to select the minute, then press the
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
:
:
◄
:
:
:
Standard
Custom
Off
Off
Off
►
ENTER button.
Mono
Move
Exit
Adjust
Timer 1 / Timer ꢀ / Timer ꢁ
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
☛
On Time : Select hour, minute, and On/Off. (To activate timer with the setting satisfied, set to On.)
Off Time : Select hour, minute, and On/Off. (To activate timer with the setting satisfied, set to On.)
Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun.
Volume : Select the required volume level.
You can set the hour, minute, directly by pressing the number buttons on the remote control.
➢
Auto Power Off
☛
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only available in timer “On” mode and prevents
overheating, which may occur if a TV is on for too long time.
English - ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Language / Melody / Light Effect / Entertainment /
Energy Saving
T V
Setup
: English
In Watching TV
1
ꢀ
Press the MENU button to display the menu.
Plug & Play
Language
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Time
Light Effect
Wall-Mount Adjustment
Melody
Entertainment
Energy Saving
:
ꢁ
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
: Off
: Off
: Off
Available options: Language, Melody, Light Effect,
Entertainment, Energy Saving
Move
Enter
Return
When you are satisfied with your setting, press the ENTER
button.
5
Press the EXIT button to exit.
Language
It is variable depending on the model. When you start using the television for the first time, you must
select the language which will be used for displaying menus and indications.
Light Effect: Off/In Standby/In Watching TV/Always
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
− Off: The blue LED is always off.
− In Standby: The blue LED lights while in Standby mode and it turns off when your TV is turned on.
− In Watching TV: The blue LED lights when watching TV and it turns off when your TV is turned off.
− Always: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
➢
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Entertainment: Off/Sports/Cinema/Game
Entertainment mode enables you to select the optimal display and sound for sports, cinema and
games.
− Off: Switches the Entertainment function off.
− Sports: Provides the optimal picture and sound quality for sports.
− Cinema: Provides the optimal picture and sound quality for movie watching.
You can experience a richer picture and enhanced sound.
− Game: Provides the optimal picture and sound quality for games. This mode accelerates the
playing speed when using an external game console connected to the TV.
If you set any of the three Entertainment modes to On, the settings will be locked and can not be
adjusted. If you want to make Picture and Sound mode adjustments, the Entertainment mode
must be turned off.
➢
The Entertainment settings are saved for each input source.
➢
Continued...
English - ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the
surrounding lighting conditions.
Tools
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
Sleep Timer
SRS TS XT
Energy Saving
Dual I-II
:
:
:
:
◄
:
Standard
Custom
Off
Off
Off
− Off: Switches off the Energy Saving mode.
− Low: Operates in standard mode regardless of the
surrounding illumination.
− Medium: Enters Medium power saving mode regardless of
the surrounding illumination.
►
Mono
Move
Exit
Adjust
− High: Enters maximum power saving mode regardless of the surrounding illumination.
Easy Setting
1 Press the TOOLS button on the remote control.
ꢀ Press the ▲ or ▼ button to select Energy Saving.
ꢁ Press the ◄ or ► button to select the required option.
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer
are shown below. But the actual screens on your PC will
probably be different, depending upon your particular
version of Windows and your particular video card. But even
if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your
computer manufacturer or Samsung Dealer.)
1
Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
ꢀ
Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
ꢁ
4
Click on Advanced. A new settings dialog box will be
displayed.
Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of
setting the Screen refresh rate.
5
Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic re-booting may commence at this moment.
English - ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
D-Sub Input
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H/V)
PS4ꢀA45ꢂ/
PS4ꢀA45ꢃ
PS50A45ꢂ/
PS50A45ꢃ
Mode
IBM
Resolution
640 x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+ / -
- / +
✔
✔
✔
✔
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1360 x 768
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
47.712
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.015
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
85.500
- / -
- / -
- / -
+ / +
+ / +
+ / +
- / -
- / -
+ / +
+ / +
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
VESA
HDMI/DVI Input
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H/V)
PS4ꢀA45ꢂ/
PS4ꢀA45ꢃ
PS50A45ꢂ/
PS50A45ꢃ
Mode
Resolution
640 x 480
800 x 600
1024 x 768
1360 x 768
31.469
37.879
48.363
47.712
59.940
60.317
60.004
60.015
25.175
40.000
65.000
85.500
- / -
+ / +
- / -
✔
✔
✔
✔
✔
✔
✔
VESA
+ / +
When using an HDMI/DVI cable connection, you must use the HDMI IN ꢀ jack.
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
Separate and Composite modes are supported. SOG is not supported.
For the PS42A456, PS42A457, PC text quality is optimum in VESA mode(1024 x 768@60Hz).
For the PS50A456, PS50A457, PC text quality is optimum in VESA mode (1360 x 768@60Hz).
English - ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PC
Preset to the PC mode by pressing the SOURCE button.
T V
Picture
: Standard
➢
Mode
ꢃ
Cell Light
Contrast
Brightness
Sharpness
1
Press the MENU button to display the menu.
ꢅ5
45
50
ꢀ
Press the ▲ or ▼ button to select Picture, then press the
ENTER button.
Auto Adjustment
Screen Adjustment
Detailed Settings
Picture Options
Reset
ꢁ
4
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
: OK
When you are satisfied with your setting, press the ENTER
Move
Enter
Return
button.
5
Press the EXIT button to exit.
Auto Adjustment in Progress
Please wait.
Auto Adjustment :
Auto adjustment allows the PC screen of set to self-adjust to
the incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Tools
Anynet+ (HDMI-CEC)
Picture Mode
Sound Mode
:
:
:
:
:
Standard
Custom
Off
Off
Off
Sleep Timer
SRS TS XT
Energy Saving
Auto Adjustment
Easy Setting
1 Press the TOOLS button on the remote control.
ꢀ Press the ▲ or ▼ button to select Auto Adjustment, then
press the ENTER button.
Adjust
Move
Exit
T V
Screen Adjustment
Screen Adjustment: Coarse/Fine/Position/Image Reset
Coarse
Fine
50
11
Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
Position
Image Reset
If the noise is not removed by Fine-tuning alone, then adjust
the frequency as best as possible (coarse) and Fine-tune
again.
After the noise has been reduced, re-adjust the picture so that
it is aligned on the center of screen.
Move
Enter
Return
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER button.
T V
Position
ꢀ Press the ◄ or ► button to adjust the screen quality, vertical
stripes may appear or the picture may be blurry. Press the
ENTER button.
Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
ꢀ Press the ENTER button.
Move
Enter
Return
Image Reset
You can replace all image settings with the factory default
values.
Image Reset is completed.
English - ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Previewing the DTV Menu System
T V
DTV
DTV
DTV
Digital Menu
The company does not guarantee the normal operation
➢
of the DTV menu for countries other than the 8 supported
countries (United Kingdom, France, Germany, Italy,
Netherlands, Spain, Switzerland, Austria) because only
these country standards are supported. In addition, when
the country of the broadcast stream differs from the
country selected by the current user, the string appearing
in the channel banner, Info, Guide, Channel List, etc. may
not be displayed properly.
Guide
Digital Channel
Setup
Language
Move
Enter
Return
Guide
Available in DTV mode. Preset to the DTV mode by using
the TV/DTV button on your remote control.
To help you navigate around the on-screen menu system
and adjust the various settings available, refer to the
following illustration.
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Digital Menu, then press
the ENTER button.
Move
Enter
Channel
Return
Guide
Now & Next Guide
Full Guide
Scheduled List
Country
: United Kingdom
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Default Guide
Now/Next
Full Guide
Digital Channel
Move
Enter
Setup
Return
Country
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Menu Transparency : Medium
Change PIN
Parental Lock
All
Subtitle
Subtitle Mode
: On
Favourites
Default/Favourites/All
Setup
Move
Enter
Return
Menu Transparency
High
Medium
Low
Opaque
Change PIN
Parental Lock
Subtitle
Parental Rating
Off
On
Subtitle Mode
Audio Format
Audio Description
Digital Text
Normal
Hard of hearing
PCM
Dolby Digital
Audio Description
Volume
Disable
Enable
Time Zone
Common Interface
System
Product Information
Signal Information
Software Upgrade
Reset
Continued...
English - ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Language
Audio Language
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Subtitle Language
Teletext Language
Preference
Primary Audio Language
Secondary Audio Language
Primary Subtitle Language
Secondary Subtitle Language
Primary Teletext Language
Move
Enter
Return
Secondary Teletext Language (depending on the Country)
The sub-items of the CI Menu may vary depending on the CAM model. (refer to page 40)
➢
Displaying Programme Information
While viewing a channel, additional information about the
current programme may be displayed.
ꢀ1:4ꢅ Sat 1 May
All Channels
1 AFDO, 1ꢂ:ꢅ
AFDO, 1ꢂ:ꢅ
No Block
SD
14:ꢀ0 - 14:ꢁꢁ
While viewing a programme, press the INFO button.
The programme information is displayed.
Contains video with AFD O; coded frame
is 1ꢂ:ꢅ
Stereo
The information is displayed:
− Parental Rating
➢
Subtitle
English
− Video Type: SD, HD, Radio
− Audio Type: Mono, Stereo, Dual, Dolby Digital
− Existence of Teletext or DVB Subtitle
− Audio Language
Exit
To exit from banner information, press the INFO button.
➢
English - ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the DTV Menu
Viewing the DTV Menu
T V
Digital Menu
After installing your antenna system and TV with appropriate
connectors.
Guide
Digital Channel
Setup
Plug in the AC main power and switch on the TV.
Language
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Digital Menu, then press
the ENTER button.
Move
Enter
Return
The main menu appears on the screen. Its left side has four
icons: Guide, Digital Channel, Setup, and Language.
DTV
DTV
DTV
DTV
DTV
Channel
Country
: United Kingdom
1. Digital Channel
Auto Store
Manual Store
This menu consists of 5 sub-menus:
Country, Auto Store, Manual Store, Edit Favourite
Channels, and Channel List.
Edit Favourite Channels
Channel List
Press the ▲ or ▼ button to select Channel, then press
the ENTER button. The Channel menu is displayed.
Move
Enter
Return
1.1 Country
Channel
Press the ENTER button. The Country menu is displayed.
Select your country by pressing the ▲ or ▼ button, then
press the ENTER button.
Country
: United Kingdom
Auto Store
Manual Store
Edit Favourite Channels
Channel List
Even though you have changed the country setting
in this menu, the country setting for Analog TV is not
changed.(Refer to page 10)
➢
Move
Enter
Return
1.ꢀ Auto Store
You can update the channel list when the broadcaster adds
new services or if you move the TV to a new location.
Auto Store
Press the ENTER button to select Auto Store. Press
the ENTER button again to start the search. When it has
finished, the number of scanned services will be displayed.
− The existing favourite channel list will not be deleted
when the channel list is updated.
0%
Services found: 0
Start
Channel:
-
− To stop the scan before it has finished, press the
ENTER button with Stop selected.
Enter
Return
Channel
If the signal status is poor, No service found! Check the
aerial connection. message is displayed.
➢
Country
: United Kingdom
Auto Store
1.ꢁ Manual Store
Manual Store
You can specify the channel for a fast channel search.
Edit Favourite Channels
Channel List
− Channel
Press the ▲, ▼ or numeric buttons (0~9) to select a
channel.
Move
Enter
Return
The available channels are 21~68. The corresponding
frequency for the selected channel is automatically set.
− Frequency
If you do not know the exact frequency, follow the above
step to select the frequency automatically using channel.
− Bandwidth
Manual Store
Channel Frequency
Bandwidth
5
1ꢃꢃ500 KHz ꢃ MHz
The available bandwidths are 7 and 8 MHz.
Search
Adjust
Return
Continued...
English - ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the red button to start the scan for digital services. When it has finished, channels are
updated in the channel list.
You can input by pressing the button on the remote control.
You can not change only frequency and when changing a channel the Frequency will be
automatically changed.
➢
➢
1.4 Edit Favourite Channels
DTV
DTV
DTV
Channel
You can edit your favourite channels using the colour buttons.
Country
: United Kingdom
In the case of DTV mode, OK or Select can be used as
the ENTER button.
Auto Store
➢
Manual Store
Edit Favourite Channels
Channel List
Press the red button in the Edit Favourite Channels menu
to display all currently stored channels.
Press the ▲ or ▼ button to select a channel you want.
Press the ENTER button. A “” icon is shown next to the
selected channel and the channel will be added to the
favourites list.
Move
Enter
Return
Edit Favourite Channels
1
ꢀ
ꢁ
4
To undo, press the ENTER button again.
➢
BBC TWO
Five
BBC THREE
abc1
Select AlI: Select all channels currently displayed.
Select None: Deselect all selected channels.
Preview: Displays (a) currently selected
channel(s).
5
QVC
Select All
Move
Select None
Select
Preview
If The Favourite Channels settings have been
completed.
➢
Return
Add
Edit Favourite Channels
You can use this function when one or more favourite
channels have been selected.
− Press the red button in the Edit Favourite Channels
menu. To add more channels, refer to the previous
section.
1
ꢀ
ꢁ
BBC TWO
BBC THREE
abc1
− To add all channels to the favourites channel list, press
the red button.
Add
Renumber
Preview
Delete
Move
Return
− To remove all channels, press the green button.
− Preview: Displays (a) currently selected channel(s).
− Press the CH LIST button to display the favourite
channel list.
Renumber (depending on the Country)
− In the Edit Favourite Channels menu, press the ▲ or ▼
button to select the required channel.
− Press the green button.
The space for entering the number is a blank.
− Enter the new channel number. Press ENTER button to store or RETURN button to cancel.
➢
Press the ◄ button to delete an entered digit.
If you enter a number already assigned to another channel, the number is assigned to the
selected channel and the previous number assigned to the selected channel is assigned
to the other channel.
➢
➢
That is, the two numbers are exchanged.
The favorite channels are automatically sorted in ascending order of channel numbers.
➢
Preview
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
previewed.
− Press the yellow button. Displays currently selected channel.
Delete
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
deleted from the favourite channels list.
− Press the blue button. The selected channel and number will be deleted.
To add a deleted channel back in to the favourite channel list, see Add.
➢
Continued...
English - ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel List
1.5 Channel List
BBC TWO
All Channels-All
ꢄ0ꢂ arte
You can display a list of all channels or your favourite
channels.
1. Test Card ‘M’...
ꢀ. BBC TWO
ꢁ. Vida00ꢁb
4. Vida004b
5. Vida005b
ꢂ. Vida00ꢂb
ꢃ. BBC THREE
ꢁ0. CBBC Channel
40. BBC NEWSꢀ4
51. BBCi
ꢄ00 ARD-MHP-DATA
ꢄ01 ARD-OnLine-K..
ꢄ0ꢀ BBC ONE
ꢄ0ꢁ MDR FERNSE..
ꢄ04 NDR FERNSEH..
ꢄ05 Vida00ꢀb
Press the ▲ or ▼ button to select Channel List, then
press the ENTER button.
It can be displayed simply by pressing the CH LIST
button.
➢
Previous Page
Move
Next Page
Watch
Favourites
TV
Return
Press the yellow button to toggle between your favourite
channels and all channels.
Your favourite channels are only displayed if they were
previously set in the Edit Favourite Channels menu
(refer to page 33).
Press the red or green button to display the previous or
next channel list page.
Press the ▲ or ▼ button to select a channel to be tuned, then press the ENTER button.
The channel number, name and an icon are displayed in the top left corner while changing
the channel. The channel number and name are displayed if the channel is one of the all
channels, and a icon if the channel is one of the favourite channels.
➢
Press the blue or CH LIST button to exit from the channel list.
Now & Next Guide
ꢀ. Guide
This menu consists of 4 sub-menus:
Now & Next Guide, Full Guide, Scheduled List, and Default
Guide.
Now
Next
ꢀ.1 Now & Next Guide / Full Guide
The EPG (Electronic Programme Guide) information is
provided by the broadcasters. Programme entries may appear
blank or out of date as a result of the information broadcast on
a given channel.
Watch
Full Guide
Favourites
Exit
The display will dynamically update as soon as new information
becomes available.
− Now & Next Guide
For the six channels indicated in the left-hand column,
displays the Current programme and the Next programme
information.
− Full Guide
Displays the programme information as time ordered 1 hour
segments. 2 hours of programme information is displayed
which may be scrolled forwards or backwards in time.
Press the ▲ or ▼ button to select Now & Next Guide or
Full Guide. Press the ENTER button. The selected guide
menu is displayed.
− Press the red button to toggle between Now & Next
Guide or Full Guide.
− Press the green button to display Favourites or All
Channels list.
− Press the yellow button to scrolls backwards quickly
(24 hours).
− Press the blue button to scrolls forwards quickly
(24 hours).
You can also display the guide menu simply by
pressing the GUIDE button.
➢
To watch a programme in the EPG list, press the
▲/▼/◄/► button to select a programme of your choice,
then press the ENTER button.
If the next programme is selected, it is scheduled with the clock icon displayed. If the
ENTER button is pressed again, the scheduling is canceled with the clock icon gone. For
➢
details about scheduling programmes, refer to the section.
Continued...
English - ꢁ4
Download from Www.Somanuals.com. All Manuals Search And Download.
To view programme information, press the ▲/▼/◄/► button to select a programme of your
choice, then press the INFO button.
Information such as the channel number, programme title and running time, status bar,
➢
and brief summary of the highlighted programme will be displayed in the top right corner
of the screen. If there is a lengthy summary, “…” will be displayed. Press the INFO button
for the full summary text.
Six channels are displayed. To scroll between channels, move to a channel using the ▲
or ▼ button. To display page by page, use the P
or
button.
DTV
Scheduled List
ꢀ.ꢀ Scheduled List
Thursday ꢀꢀ Apr
15:ꢁ0 ~ 1ꢄ:00 Once
Animal Park
If you make a scheduled viewing list of programs you may
like to see, the channel will be automatically switched to the
scheduled program at the scheduled time even if you are
watching another program.
ꢀ BBC TWO
Thursday ꢀꢀ Apr
ꢀ BBC TWO
ꢀ0:00 ~ ꢀ1:00 Once
The Hairy Biker’s
Press the red button to add a new programme. The
menu for adding a programme is displayed with Channel
selected.
Add Programme
Edit
Return
Delete
Move
Press the ▲/▼ and ENTER buttons to set the required
channel, time, date, and frequency. When you are satisfied
with your settings, save the adjusted schedule by pressing
the red button.
DTV
Scheduled List
Channel
Time
ꢀ0 MOJO
1ꢅ:00
-
ꢀ1:00
If you want to edit the scheduled programme, select a
programme by pressing the ▲ or ▼ button, then press
the green button. If necessary, select the programme to
be deleted by pressing the ▲ or ▼ button, then press the
blue button.
Date
Thu ꢂ Jan ꢀ00ꢄ
Once
Frequency
Save
Cancel
Return
Adjust
Move
When watching analog TV, the reserved DTV channel
➢
cannot be changed. The channel is only changed
automatically to the reserved channel when you are
watching DTV.
Scheduling programme only functions with the
➢
television already turned on, and not from standby
mode. For details about switching the television on
and off automatically, refer to page 9.
DTV
ꢀ.ꢁ Default Guide
Guide
You can preset the default guide style.
Now & Next Guide
Full Guide
Press the ▲ or ▼ button to select the required option
(Now/Next or Full Guide), then press the ENTER button.
The selected option for default guide is displayed on the
EPG menu and the channel list appears.
Scheduled List
Default Guide
: Full Guide
Move
Enter
Guide
Return
DTV
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Now/Next
Full Guide
Move
Enter
Return
Continued...
English - ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Guide
Now & Next Guide
ꢀ.4 All Channels and Favorite Channels
In the EPG menu, you can display all channels or favourite
channels.
Full Guide
Scheduled List
Default Guide
Press the green button repeatedly to toggle between the
all and favourite channels list.
: Full Guide
When the favorite channel list has not been set up:
− The favorite list is empty. Would you like to choose
your favorite now? message is displayed.
− Select Yes. The Edit Favourite Channels menu is
displayed. If you select No, all channels will remain
unchanged.
Move
Enter
Return
Now & Next Guide
− To edit the favourite channels, refer to page 33 for more
details.
Now
Next
All Channels is the list of channels that have
➢
been scanned by the channel list update. All
channels are displayed in the all channel mode.
Favourites (favourite channels) is the list of
channels that has been set in the Edit Favourite
Channels menu (refer to page 33).
Watch
Full Guide
Favourites
Exit
Now & Next Guide
When there is no channel information, the No
Data message will be displayed and you will not
be able to change the channel even if you press
the ENTER button.
The favourites list is empty.
Would you like to choose your
favourites now?
Yes
No
When the No Data message appears and you
cannot change the channel, press the channel
number directly using the numeric buttons.
Watch
Full Guide
Favourites
Exit
ꢁ. Language
This menu consists of 4 sub-menus:
DTV
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Audio Language, Subtitle Language, Teletext Language,
and Preference.
ꢁ.1 Audio Language / Subtitle Language / Teletext Language
You can change the default value for subtitle, audio and
teletext languages.
Move
Enter
Return
Press the ▲ or ▼ button to select required menu (Audio
Language, Subtitle Language, or Teletext Language),
then press the ENTER button. The options of the selected
menu are displayed.
Continued...
English - ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
DTV
DTV
Language
Audio Language
ꢁ.ꢀ Preference
This menu consists of 6 sub-menus:
Primary Audio Language, Secondary Audio Language,
Primary Subtitle Language, Secondary Subtitle Language,
Primary Teletext Language, and Secondary Teletext
Language (depending on the Country).
Using this feature, users can select one of the languages
(English, German, Italian, Swedish, French, Welsh, Gaelic,
Irish, Danish, Finnish, Spanish, Dutch). The language selected
here is the default when the user selects a channel.
Subtitle Language
Teletext Language
Preference
Move
Enter
Preference
Primary Audio Language
Return
: English
Press the ▲ or ▼ button to select required menu (Primary
Audio Language, Secondary Audio Language, Primary
Subtitle Language, Secondary Subtitle Language,
Primary Teletext Language, or Secondary Teletext
Language), then press the ENTER button.
Secondary Audio Language : English
Primary Subtitle Language : English
Secondary Subtitle Language : English
Primary Teletext Language : English
The options of the selected menu are displayed.
Press the ▲ or ▼ button to select required option
(English, German, Italian, Swedish, French, Welsh,
Gaelic, Irish, Danish, Finnish, Spanish, Dutch), then
press the ENTER button.
Move
Enter
Return
Preference
Primary Audio Language
:
English
German
Secondary Audio Language :
If you change the language setting, the Audio
Language, Subtitle Language, and the Teletext
Language of the Language menu (refer to page 36)
are automatically changed to the selected language.
The Audio Language, Subtitle Language, and the
Teletext Language of the Language menu show a
Italian
➢
Primary Subtitle Language :
Swedish
French
Secondary Subtitle Language :
Welsh
Primary Teletext Language :
Move
Enter
Return
list of languages supported by the current channel and the selection is highlighted. If you
change this language setting, the new selection is only valid for the current channel. The
changed setting does not change the setting of the Primary Audio Language, Primary
Subtitle Language, or the Primary Teletext Language of the Preference menu.
Continued...
English - ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Setup
4. Setup
This menu consists of 11 sub-menus:
Menu Transparency : Medium
Change PIN
Menu Transparency, Change PIN, Parental Lock, Subtitle,
Subtitle Mode, Audio Format, Audio Description, Digital
Text, Time Zone, Common Interface and System.
Parental Lock
Subtitle
Subtitle Mode
: Off
4.1 Menu Transparency
Move
Enter
Setup
Menu Transparency : High
Return
You can set the translucency of the on-screen menu.
DTV
Press the ▲ or ▼ button to select required option (High,
Medium, Low, or Opaque), then press the ENTER button.
Medium
Low
Change PIN
Parental Lock
Subtitle
Opaque
: On
4.ꢀ Change PIN / Parental Lock
Subtitle Mode
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by a 4-digit
PIN (Personal Identification Number) code that is defined by
the user.
Move
Enter
Setup
Return
DTV
The on-screen menu will instruct you to assign a PIN code
(you can change it later, if necessary).
Menu Transparency : Medium
Change PIN
Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The Parental Lock menu are displayed
with the Parental Rating selected.
Parental Lock
Subtitle
Subtitle Mode
: Off
The default PIN code for a new TV set is 0000.
➢
If you enter an invalid PIN code, the Invalid PIN
code. Please try again. message is displayed.
Press the ENTER button. Press the ▲ or ▼ button to
select the age rating you want to lock out, then press the
ENTER button.
Move
Enter
Return
DTV
Parental Lock
Enter PIN
If you want to change the PIN code, press the ▲ or ▼
button to select Change PIN, then press the ENTER
button.
− Enter your new PIN code by using the numeric buttons
(0~9). The Confirm New PIN is displayed.
− Re-enter your new PIN code to confirm by using the
numeric buttons (0~9). The Your PIN code has been
changed successfully. message is displayed.
If you forget the PIN code, press the remote control
buttons in the following sequence, which resets the PIN to
0-0-0-0: POWER (Off) MUTE ꢄ ꢀ 4 POWER
(On).
.. Enter PIN
Return
DTV
Change PIN
Enter New PIN
➢
.. Enter PIN
Return
DTV
Change PIN
Confirm New PIN
.. Enter PIN
Return
Continued...
English - ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
DTV
DTV
Setup
4.ꢁ Subtitle / Subtitle Mode / Audio Format / Audio Description /
Digital Text
Menu Transparency : Medium
Change PIN
You can use various settings to suit your personal preferences.
Parental Lock
Press the ▲ or ▼ button to select required menu
(Subtitle, Subtitle Mode, Audio Format, Audio
Description or Digital Text), then press the ENTER
button. The options of the selected menu are displayed.
Press the ▲ or ▼ button to select required option, then
press the ENTER button.
Subtitle
Subtitle Mode
: Off
Move
Enter
Setup
Return
− Subtitle : On / Off
You can select these options simply by pressing the
Menu Transparency : Medium
Change PIN
➢
SUBTITLE button on the remote control.
Parental Lock
− Subtitle Mode : Normal (basic subtitle) / Hard of hearing
(subtitle for a hearing-impaired person)
Subtitle
Subtitle Mode
:
Off
On
If the programme you are watching does not support
➢
the Hard of hearing function, Normal automatically
activates even though Hard of hearing mode is
selected.
Move
Enter
Setup
Return
− Audio Format
Menu Transparency : Medium
Change PIN
You can only hear Dolby Digital sound through the audio
receiver connected through an optical cable. You can only
hear PCM sound through the main speaker.
When sound is emitted from both the main speaker and the
audio receiver, a sound echo may occur due to the decoding
speed difference between the main speaker and the audio
receiver. In this case, use the internal mute function.
Parental Lock
Subtitle
Subtitle Mode
: On
: Normal
Move
Enter
Return
Even if you have selected PCM or Dolby Digital in Audio
➢
Format, when the input signals are any format of PCM
and Dolby Digital, the input format is applied regardless
of the setting. If the input signals are not any of those,
the setting is not applied.
− Audio Description
This is an auxiliary audio function that provides an additional audio track for visually challenged
persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent
along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off
and control the volume.
− Digital Text : Enable / Disable (UK only)
If the programme is broadcast with digital text, this feature is enabled.
MHEG (Multimedia and Hypermedia Information Coding Experts Group)?
➢
➢
An International standard for data encoding systems used in multimedia and hypermedia.
This is at a higher level than the MPEG system which includes data-linking hypermedia such
as still images, character service, animation, graphic and video files as well as multimedia
data. MHEG is user runtime interaction technology and is being applied to various fields
including VOD (Video-On-Demand), ITV (Interactive TV), EC (Electronic Commerce), tele-
education, tele-conferencing, digital libraries and network games.
DTV
4.4 Time Zone (Spain only)
Setup
You can select the time zone where you are located.
▲
Audio Format
: PCM
►
►
►
This menu is only enabled when you select a country
supported by the time zone.
➢
Audio Description
Digital Text
: Enable
Time Zone
Common Interface
▼
►
Move
Enter
Return
Continued...
English - ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Application Info.
4.5 Common Interface
Type: CA
− Installing the CI Card
Manufacturer: Canal Plus
Info: Top Up TV
Purchase the CI CAM module by visiting your nearest
dealer or by phone.
Insert the CI CARD into the CAM in the direction of the
arrow until it fits.
Insert the CAM with the CI CARD installed into the
common interface slot.
Return
Insert the CAM in the direction of the arrow, right up
to the end so that it is parallel with the slot.
➢
CI Menu
Check if you can see a picture on a scrambled signal
channel.
You can install the CAM anytime whether the TV is
ON or OFF.
➢
− Application Info.
This contains information on CAM inserted in the CI slot and
displays it.
Move
Enter
Exit
Press the ENTER button to display the information for your application.
− CI Menu
This helps the user select an item from the CAM-supported menu.
Press the ENTER button. The options of the selected menu are displayed.
Press the ▲ or ▼ button to select the required option, then press the ENTER button.
Select the CI Menu based on the PC Card menu.
➢
4.ꢂ System
This menu consists of 5 sub-menus:
DTV
DTV
DTV
DTV
Setup
Product Information, Signal Information, Software
Upgrade, and Reset.
System
− Product Information
You can view your product information. For service or repair,
please contact a Samsung approved dealer.
Move
Enter
Return
Press the ENTER button with Product Information
selected. The product information menu is displayed.
− Software Version / Firmware Version
System
Product Information
Signal Information
Software Upgrade
Reset
− Signal Information
You can get information about the signal status.
Press the ENTER button with Signal Information
selected. The technical information for signal status is
displayed.
Move
Enter
Return
Product Information
− Service / Service ID / Multiplex / Network / Bit
error level / Signal Strength
Software Version: T-PERLDEUC-1004
Firmware Version: T-EMMAZDEUB-010ꢂ
Return
Signal Information
Service: ?
Service ID: 0000
Multiplex: ? (TSID 0000,ONID 0000)
Network: ? (ID 0000)
Bit error level:
10
0
Signal Strength:
Continued...
Return
English - 40
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
Software Upgrade
Software Information
− Software Upgrade (Option)
To keep your product up-to-date with new digital television
features then software upgrades are periodically broadcast
as part of the normal television signal. It will automatically
detect these signals and display the software upgrade
banner. You are given the option to install the upgrade.
Manual Upgrade
Standby Mode Upgrade : On
Software Inforamtion
Press the ENTER button, then the current software
version is shown. To display the software version
information, press the ENTER button again.
Manual Upgrade
Press the ENTER button to search for new software from the currently broadcasting channels.
Standby Mode Upgrade : On / Off
Move
Enter
Return
Press the ENTER button. To continue software upgrade with master power on, Select On by
pressing the ▲ or ▼ button.
45 minutes after entering standby mode, a manual upgrade is automatically conducted. Since
the power of the unit is turned on internally, the screen may be on slightly for the PDP product.
This phenomenon may continue for more than 1 hour until the software upgrade is completed.
− Reset
You can reset the values stored to the factory default values.
DTV
Reset
The Reset operation deletes all channel information
and user preferences returning all values to their default
factory state.
Press the ENTER button with Reset selected.
The Enter PIN is displayed.
Enter your current 4-digit PIN code by using the
numeric buttons (0~9). The warning message is
displayed. All values will be reset by pressing the
coloured buttons (red, green, yellow, and blue) in turn.
➢
WARNING: All channel settings and user preferences will be
lost and returned to the factory defaults. It is recommended
that
a
reset is performed only when serious problems are
experienced.
Return
The default PIN of a new TV set is “0-0-0-0”.
When PIN is changed in Child Lock, the PIN for
resetting automatically changes.
➢
➢
When reset is complete, it operates DTV Plug & Play
(DTV Auto Store, Time Zone-depending on the country,
Time Setting) and exits from the digital TV mode without changing to the analog TV mode.
(Refer to page 10)
English - 41
Download from Www.Somanuals.com. All Manuals Search And Download.
+
What is Anynet ?
+
Anynet is an AV network system that enables an easy-to-use AV interface for users by controlling
+
all connected AV devices through the Anynet menu when Samsung Electronics AV devices are
connected.
+
Connecting Anynet Devices
+
+
The Anynet system supports AV devices supporting Anynet only.
+
Check if there is an Anynet mark on the AV device to be connected to the TV.
To directly connect to TV
Connect the [HDMI 1], [HDMI
TV
+
+
+
2] or [HDMI 3] jack on the TV
and the HDMI OUT jack of the
Anynet Device 1 Anynet Device ꢀ Anynet Device ꢁ
+
corresponding Anynet device
using the HDMI cable.
HDMI Cable
HDMI Cable
HDMI Cable
To connect to Home Theatre
1
Connect the [HDMI 1],
[HDMI 2] or [HDMI 3]
jack on the TV and the
HDMI OUT jack of the
corresponding Anynet
device using the HDMI
cable.
TV
+
+
Anynet Device 1
Anynet Device ꢀ
+
ꢀ
Connect the HDMI IN jack
of the home theatre and
the HDMI OUT jack of the
HDMI Cable
HDMI Cable
+
corresponding Anynet
device using the HDMI
cable.
+
Home Theatre
Anynet Device ꢁ
HDMI Cable
HDMI Cable
Optical Cable
Connect only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio
Input on the receiver.
➢
Connect only one receiver.
➢
➢
You can listen to 5.1 channel sound through the home theatre’s speakers. Otherwise, you can only
listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of
the home theatre and the TV correctly to listen to TV sound through the home theatre. However, you
cannot listen to sound from the BD recorder that is sent to the home theatre via the TV in 5.1 channel
sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home
theatre.
+
You can connect an Anynet device using the HDMI cable. Some HDMI cables may not support
Anynet functions.
➢
+
+
+
+
Anynet works when the AV device supporting Anynet is in the Standby or On status.
➢
➢
Anynet supports up to 8 AV devices in total.
English - 4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
+
Setting Up Anynet
+
The following settings are to use Anynet functions.
TV
P 1
+
Using the Anynet Function
View TV
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
Press the ▲ or ▼ button to select Anynet (HDMI-CEC), then
press the ENTER button.
Select Device
Record
Menu on Device
Device Operation
+
ꢀ
ꢁ
4
5
Receiver
Setup
:Off
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Move
Return
Enter
+
Press the ▲ or ▼ button to select Anynet (HDMI-CEC), then
press the ENTER button.
Setup
Press the ▲ or ▼ button to select On, then press the ENTER
+
Anynet (HDMI-CEC)
:
:
Off
On
button.
Auto Turn Off
+
The Anynet (HDMI-CEC) function is enabled.
➢
➢
➢
+
Searching Connections
If you select Off, Anynet (HDMI-CEC) is disabled.
+
When the Anynet (HDMI-CEC) function is disabled, all the
+
Anynet related operations are deactivated.
Move
Enter
Return
+
Turning an Anynet Device Off Automatically when the TV is
Turned Off
Setup
4
5
Press the ▲ or ▼ button to select Auto Turn Off, then press
the ENTER button.
+
Anynet (HDMI-CEC)
: On
Press the ▲ or ▼ button to select Yes, then press the
ENTER button.
Auto Turn Off
:
No
The Auto Turn Off function is enabled.
Searching Connections
➢
Yes
If you select No, the Auto Turn Off function is canceled.
➢
Press the EXIT button to exit.
Move
Enter
Return
The Select Device setting of the TV remote control is to be set
➢
➢
+
to TV to use the Anynet function.
If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned
off. However, if the device is recording, it may not be turned off.
+
Scanning and Switching between Anynet Devices
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
TV
P 1
View TV
DVDR1
DVDRꢀ
DVD1
+
ꢀ
ꢁ
4
Press the ▲ or ▼ button to select Anynet (HDMI-CEC), then
Select Device
Record
press the ENTER button.
DVDꢀ
Press the ▲ or ▼ button to select Select Device, then press
the ENTER button.
Menu on Device
Device Operation
Press the ▲ or ▼ button to select to a particular device and
press the ENTER button.
Receiver
Setup
:Off
It is switched to the selected device.
If you cannot find a device you want, press the ▲ or ▼ button
to select Searching Connections, then press the ENTER
button.
Move
Return
Enter
5
Setup
+
The meassage Configuring Anynet connection... is
+
Anynet (HDMI-CEC)
:
:
On
Yes
displayed. When searching devices completes, the connected
Auto Turn Off
+
devices are listed in the Anynet menu.
Switching to the selected devices may take up to 2 minutes.
You cannot cancel the operation during the switching
operation.
Searching Connections
➢
➢
Move
Enter
Return
The time required to scan for devices is determined by the
number of connected devices.
When the device scan is complete, the number of found devices is not displayed.
➢
➢
Although the TV automatically scans devices when it is turned on using the POWER button, devices
connected when the TV is on or under a specific circumstance are not displayed in the device list.
Therefore select Searching Connections menu to search devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
➢
+
+
Anynet function. Make sure to switch to an Anynet device by using the TOOLS button.
Continued...
English - 4ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
+
Anynet Menu
+
+
The Anynet menu changes depending on the type and status of the Anynet devices connected
to the TV.
+
Anynet Menu
Description
+
View TV
Switches from Anynet to TV broadcast mode.
Your TV connects to the corresponding device.
Select Device
Record
Starts a recording. (This menu works only for a device supporting
recording.)
Menu on Device
Device Operation
Shows the menu of the connected device.
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Shows the play control menu of the connected device.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
Receiver
Setup
Sound is output through the receiver.
+
You can set the environment for using Anynet .
+
TV Remote Control Buttons Available in Anynet Mode
Device Type Operating Status
After switching to the
Available Buttons
Numeric buttons
device, when the menu of
the corresponding device is
displayed on the screen.
▲/▼/◄/►/ENTER buttons
Colour buttons
EXIT button
+
Anynet Device
(Backward search)
(Forward search)
(Stop)
After switching to the device,
while playing a file
(Play/Pause)
After switching to the device,
when you are watching a TV
programme
Device with built-in Tuner
Audio Device
P
/
button
/
button
When a Receiver is activated
MUTE button
+
The Anynet function only works when the remote control is set to TV.
➢
➢
➢
The REC button works only while in the recordable state.
+
+
You cannot control Anynet devices using the buttons on the side of the TV. You can control Anynet
devices only using the TV remote control.
+
The TV remote control may not work under certain conditions. In this case, reselect the Anynet
device.
➢
+
The Anynet functions don’t operate for the products from other manufacturers.
➢
➢
➢
+
In Anynet mode, the colour buttons may not work properly.
The operations may differ depending on the device.
,
Recording
You can make a recording of a TV programme using a recorder.
Press the REC button.
+
Recording begins. (Only when the Anynet enabled recording device is connected.)
The current TV programme is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
➢
You can also record the source streams by selecting Record after pressing the TOOLS button.
Before recording, check whether the antenna jack is properly connected to the recording device.
For the antenna connection to the recording device, refer to its user manual.
➢
➢
English - 44
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1
ꢀ
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
TV
P 1
+
Press the ▲ or ▼ button to select Anynet (HDMI-CEC), then press the ENTER
View TV
button.
Select Device
Record
ꢁ
4
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
Menu on Device
Device Operation
5
➢
Press the EXIT button to exit.
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
Receiver
Setup
:On
Move
Exit
Enter
➢
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
In case of a content with copyright problems, listening through the receiver may not properly operate.
➢
➢
Check Points before Requesting Service
Symptom
Anynet does not work.
Solution
+
+
+
■
Check if the device is an Anynet device. The Anynet system
+
supports Anynet devices only.
■
■
■
■
Connect only one receiver.
+
Check if the Anynet device power cord is properly connected.
+
Check the Anynet device’s Video/Audio/HDMI cable connections.
+
+
Check whether Anynet (HDMI-CEC) is set to On in the Anynet
setup menu.
■
■
■
■
Check whether the TV remote control is in TV mode.
+
Check whether it is Anynet exclusive remote control.
+
Anynet doesn’t work at a certain condition. (Searching channels)
When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
+
+
+
+
■
■
Check if the Anynet Function of Anynet device is set on.
+
I want to start Anynet .
Check if the Anynet device is properly connected to the TV and
+
check if the Anynet (HDMI-CEC) is set to On in the Anynet
Setup menu.
■
Press the TV button on the TV remote control to switch to TV.
+
Then press the TOOLS button to show the Anynet menu and
select a menu you want.
+
+
I want to exit Anynet .
■
■
Select View TV in Anynet menu.
Press the SOURCE button on the TV remote control and select a
+
device other than Anynet devices.
■
Press any of P, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
+
tuner-embedded Anynet device is not connected.)
The message Connecting to
■
■
You cannot use the remote control when you are configuring
+
+
Anynet device… appears
Anynet or switching to a view mode.
+
on the screen.
Use the remote control when the Anynet setting or switching to
view mode is complete.
+
The Anynet device does
■
You cannot use the play function when Plug & Play is in progress.
not play.
+
The connected device is not
displayed.
■
■
■
Check whether or not the device supports Anynet functions.
Check whether or not the HDMI cable is properly connected.
+
+
Check whether Anynet (HDMI-CEC) is set to On in the Anynet
setup menu.
+
■
■
Search Anynet devices again.
+
You can connect an Anynet device using the HDMI cable only.
Some HDMI cables may not support Anynet functions.
+
The TV programme cannot
be recorded.
The TV sound is not output
through the receiver.
■
■
Check whether the antenna jack on the recording device is
properly connected.
Connect the optical cable between TV and the receiver.
English - 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext Feature (depending on the model)
Most television stations provide written information services via teletext. The index page of the
teletext service gives you information on how to use the service. In addition, you can select
various options to suit your requirements by using the remote control buttons.
For teletext information to be displayed correctly, channel reception must be stable. Otherwise,
information may be missing or some pages may not be displayed.
☛
1
2
3
TV/DTV
Exit from the teletext display (depending on the model)
(store)
Used to store the teletext pages.
(size)
Press to display the double-size letters in the upper half of the
screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
4
5
(reveal)
Used to display the hidden text (answers to quiz games, for
example). To display normal screen, press it again.
Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the
different topics covered on a teletext page are colour-coded and
can be selected by pressing the coloured buttons. Press one
of them corresponding to the required. The page is displayed
with other coloured information that can be selected in the same
way.
To display the previous or next page, press the corresponding
coloured button.
6
7
(teletext on/mix)
Press to activate teletext mode after selecting the channel
providing the teletext service. Press it twice to overlap the
teletext with the current broadcasting screen.
(mode)
Press to select the teletext mode (LIST/FLOF).
If you press it in the LIST mode, it switches into the List save
mode.
In the List save mode, you can save teletext page into list using
the
(store) button.
8
9
0
!
(sub-page)
Used to display the available sub-page.
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(index)
Used to display the index (contents) page at any time while you
are viewing teletext.
@
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages
which follow on automatically. To resume, press it again.
#
(cancel)
Used to display the broadcast when searching for a page.
You can change teletext pages by pressing the numeric buttons
on the remote control.
➢
Continued...
English - 4ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
The teletext pages are organized according to six categories:
Part
Contents
A
B
C
D
E
F
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
Teletext information is often divided between several pages
displayed in sequence, which can be accessed by:
Entering the page number
Selecting a title in a list
Selecting a coloured heading (FASTEXT system)
➢
➢
Press the TV/DTV button to exit from the teletext display.
English - 4ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product Family
inch
VESA Spec. (A * B)
200 100
Standard Screw
Quantity
23 ~ 26
32 ~ 40
M4
M6
*
200 200
*
400 * 400
600 * 400
46 ~ 52
57
LCD-TV
4
700 * 400
(No VESA)
M8
M8
57 ~ 70
80 ~
800 * 400
1400 * 800
400 * 400
600 * 400
42 ~ 58
63
4
6
676 * 407
(No VESA)
PDP-TV
63 ~ 70
80 ~
800 * 400
4
4
1400 * 800
We provided the standard dimensions for wall mount kits as shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
assembly are provided.
➢
➢
Do not use screws longer than the standard dimension, as they may cause damage to the inside of
the TV set.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the
screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the product or cause the product to fall,
leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall
mount is used or the consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our
dedicated wall mount kit for this model.
➢
➢
➢
➢
➢
➢
Do not exceed 15 degrees tilt when mounting this TV.
Do not install your Wall Mount Kit while your TV is turned on.
It may result in personal injury due to electric shock.
English - 4ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall- mount adjustment (Sold separately)
Once the auto wall mount is installed, the position of your TV can be easily adjusted.
Rear Panel
Auto Wall-Mount
Serial Cable(1P to 1P)(Not supplied)
Entering the menu
Press the ▲, ▼, ◄ or ► button on your remote control.
1
T V
Setup
: English
In Watching TV
Plug & Play
Language
Time
The Wall Mount Adjustment screen is displayed.
➢
➢
If the Wall Mount Adjustment screen is not displayed
when clicking on a direction button while watching your
TV, use the menu to display that screen.
Light Effect
:
Wall-Mount Adjustment
Melody
: Off
: Cinema
: Off
Entertainment
Energy Saving
• Press the MENU button to display the menu. Press the
▲ or ▼ button to select Setup, then press the ENTER
button.
• Press the ▲ or ▼ button to select Wall-Mount
Adjustment, then press the ENTER button.
Move
Enter
Return
Wall-Mount Adjustment
►
Remembering the Position
►
ꢀ
Adjust to the desired position using the ▲, ▼, ◄, ► buttons.
If you press an arrow button when no OSD is displayed
on the TV screen, the Adjustment screen appears.
Press the INFO button to reset. Press the ◄ or ► button
to select Yes, then press the ENTER button. The position
is initialized to the default setting.
➢
Position
Adjust
1
2
3
INFO
Save
Center
➢
ꢁ
Press the blue button.
Press the ▲ and ▼ buttons to select a save mode from
either Position1, Positionꢀ or Positionꢁ in order to save the
current position.
Save
To not save the current position, press the RETURN
button.
When selecting a save mode, you cannot use the Color
buttons.
➢
Select a mode to Save.
Position 1
➢
Position 2
Position 3
4
5
Press the ENTER button to save.
When Position1 is selected, the message Current
position saved as Position1 is displayed.
➢
Adjust
Enter
Return
Press the ENTER button.
The saved Position appears on the left side of the OSD.
➢
English - 4ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving to the remembered position
1
ꢀ
Complete Step 1 of Entering the menu.
Wall-Mount Adjustment
Position 1
Pressing a Color (Red, Green, Yellow) button moves the auto
wall mount to the saved position.
►
►
You can move the wall mount to one of the 3 pre-set
positions by pressing the Red (Position 1), Green
(Position 2) or Yellow (Position 3) buttons.
➢
Position
Adjust
1
2
3
INFO
Save
Center
If you adjust the positon after moving to a pre-set
position, the position display will disappear.
➢
For installation, refer to the Installation Manual provided with
the wall mount.
For product installation and the installation and moving of the
wall mount, make sure to consult a specialized installation
company.
➢
➢
This installation manual is to be used when attaching the wall
mount to a wall. When attaching to other building materials,
please contact your nearest dealer.
➢
+
The auto wall mount will not work when Anynet is operating.
➢
➢
42 inches model is not compatible with the older wall mount
model (WMN5090A).
How to assemble the Stand-Base (depending on the model)
Using the 6 screws for securing the stand base and the
monitor, firmly attach the monitor to the stand base.
(The exterior of the set may be different than the picture.)
In case of installing your TV on the wall,
close the cover (1) on the stand-base
connection part using two screws for
hiding.
Warning
Firmly secure the stand to the TV
before moving it, as the stand may
fall and could cause serious injury.
Two or more people should carry
➢
the TV. Never lay the TV on the
floor because of possible damage
to the screen.
Always store the TV upright.
English - 50
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the television and contact your local dealer.
No sound or picture
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the
button on the remote control.
(Power) button (On/Off) on the front panel or press the POWER
Check the picture contrast and brightness settings.
Check the volume.
Check if TV Speaker is set to Off.
Normal picture but no sound
Check the volume.
Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
Adjust the colour settings.
Check that the broadcast system selected is correct.
Sound and picture interference
Try to identify the electrical appliance that is affecting the television, then move it further away.
Plug the television into a different main socket.
Blurred or snowy picture, distorted sound
Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check that the “+” and “–” ends of the batteries are inserted correctly.
Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
On your computer check; Power, Signal Cable.
The TV is using its power management system.
Move the computer’s mouse or press any key on the keyboard.
On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
The TV is using its power management system.
Press the Source button on the panel or remote control.
Turn the TV off and on.
The damaged picture appears in the corner of the screen.
If Just Scan is selected in some external devices, the damaged picture may appear in the corner of
the screen. This symptom is caused by external devices, not TV.
The “Resets all settings to the default values” message appears.
This appears when you press and hold the EXIT button for a while. The product settings are reset to
the factory defaults.
English - 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and
are subject to modification without notice.
Model Name
PS4ꢀA45ꢂ/PS4ꢀA45ꢃ
42 inch
PS50A45ꢂ/PS50A45ꢃ
50 inch
Screen Size (Diagonal)
PC Resolution
1024 x 768 @ 60 Hz
10 W + 10 W
1360 x 768 @ 60 Hz
10 W + 10 W
Sound (Output)
Dimension (WxHxD)
Body
With stand
1055 x 725 x 94 mm
1055 x 725 x 316 mm
1231 x 756 x 95 mm
1231 x 756 x 316 mm
Weight
Body
With stand
27 Kg
31 Kg
35 Kg
37 Kg
Environmental
Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
This device is a Class B digital apparatus.
Design and specifications are subject to change without prior notice.
➢
For the power supply and Power Consumption, refer to the label attached to the product.
English - 5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning! Important Safety Instructions
Please read the appropriate section that corresponds to the marking on your Samsung product before attempting
to install the product.
This symbol indicates that high voltage is
present inside.
It is dangerous to make any kind of contact
with any internal part of this product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). THERE ARE NO
USER SERVICEABLE PARTS INSIDE. REFER ALL
SERVICING TO QUALIFIED PERSONNEL.
This symbol alerts you that important
literature concerning operation and maintenance
has been included with this product.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation.
To ensure reliable operation of this apparatus, and to protect it from overheating, these slots and openings must never
be blocked or covered.
- Do not cover the slots and openings with a cloth or other materials.
- Do not block the slots and openings by placing this apparatus on a bed, sofa, rug or other similar surface.
- Do not place this apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper venti lation is
provided.
• Do not place this apparatus near or over a radiator or heat resistor, or where it is exposed to direct sunlight.
• Do not place sources of heat on this apparatus, such as a candles, ash trays, incense or other similar items.
• Do not place a water containing vessel on this apparatus, as this can result in a risk of fire or electric shock.
• Do not expose this apparatus to rain or place it near water(near a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool etc.).
If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately.
You can clean this apparatus with damp cloth when necessary, but be sure to unplug the apparatus first.
• Do not expose this apparatus to extreme temperature conditions or to extreme humidity conditions.
• This apparatus use batteries. In your community there might be regulations that require you to dispose of these batteries
properly under environmental considerations. Please contact your local authorities for disposal or recycling information.
• To cut off the power source, unplug this apparatus from the wall outlet.
• Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric
shock.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plug end, adaptors and the point where they exit from the appliance.
• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor
correspondsto the local electrical supply.
• Never insert anything metallic into the open parts of this apparatus. Doing so many create a danger of electric shock.
• To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
• Be sure to hold the plug, not the cord, when disconnecting this apparatus from an electric socket.
• Locate this apparatus near an easily accessible AC outlet.
• If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it
- unplug it immediately and contact an authorized dealer or service center.
• Unplug this apparatus from the AC outlet before any service.
• Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an
extended period of time (especially when children, elderly or disabled people will be left alone in the house).
- Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate
sparks and heat or the insulation to deteriorate.
• Be sure to contact an authorized service center, when installing your set in a location with heavy dust, high or low
temperatures, high humidity, chemical substances and where it operates for 24 hours such as the airport, the train
station etc. Failure to do so may cause serious damage to your set.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring the Mains Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated
on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must
be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point,
you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative but to cut off the plug, remove the fuse and then safely dispose of the plug. Do NOT
connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The
wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
Warranty Card
UNITED KINGDOM
This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against
defective materials and workmanship. In the event that warranty service is required, you should return the product to the
retailer from whom it was purchased. However, Samsung Authorised Dealers and Authorised Service Centres in other EC
Countries will comply with the warranty on the terms issued to purchasers in the country concerned. In case of difficulty,
details of our Authorised Service Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 1ꢃꢀ4ꢁ
Edinburgh, EH11 4YB
United Kingdom
Tel: 0ꢄ45 SAMSUNG (ꢃꢀꢂꢃꢄꢂ4)(UK & Northern Ireland)
Tel: 0ꢄ1ꢄ ꢃ1ꢃ 100 (Republic of Ireland Only)
Fax: 0ꢄ45 ꢂ50 ꢄ0ꢄ0
WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and
is presented with the original invoice or sales slip or confirmation, and the serial number on the product has not been
defaced.
2. Samsung’s obligations are limited to the repair or, at its discretion, replacement of the product or the defective part.
3. Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried out by non Samsung Dealers and, any such repair work and
damage to the products caused by such repair work will not be covered by this warranty.
4. This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in
order to conform to national or local technical or safety standards in force in any Country other than the one for which
the product was originally designed and manufactured.
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally
left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
|