EV-7105-NPEQ (NTSC)
Mini PTZ Camera
Manual
•
•
•
•
10x Optical zoom and 10x digital zoom
Up to 100x zoom
Up to 360°/sec pan/tilt motion
Outdoor or indoor use
•
•
Up to 127 preset target views, each
with its own characteristics such as
white balance and auto exposure
Up to 95° tilt, up to 180° with auto-flip
Note: Model numbers that end with “Q” or products that have a round green “Q” sticker signify RoHS compliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
ENFOEVR-7C10E5R-NPMEiPnTiZPCTaZmeCraaFmeaeturaresFaenadtuFurnecstioannsd Functions
1
1
Powerful yet f xible camera: /4-inch CCD camera with Day and Night function, up to 100X zoom (m x. 10X
Powerful and Flexible: The ENFORCER Mini PTZ Camera is equipped with a /4-inch CCD, a powerful Day and Night
optical zoom and 10X digital zoom), multiple focus modes, and full programmability.
function, up to 100x zoom (max. 10x optical zoom and 10x digital zoom), multiple focus modes, and other fully programmable
features.
Powerful Pan/Tilt functionality: The camera features 360-degree pan motion, and it can be programmed to
Pan/Tilt Functionality: The camera features 360° endless pan motion and 95° tilt. It can be programmed to automatically
automatically flip the im ge if it tilts under the unit. The pan/til function uses vector drive technology s that it
flip the image if it tilts under the unit. The pan/tilt function uses vector drive technology so that it quickly moves to the target
quickly move to the arget while ensuring the view on th monitor flows sm othly.
while ensuring the view on the monitor flows smoothly.
On-Screen Display (OSD) programming: The On-Screen Display shows camera status and settings together
On-Screen Display (OSD): The On-Screen Display shows camera status and settings together with the preset target views.
with the preset target views.
A Wide Range of Programmable Options:
Flexible programming capabilities:
• Up to 127 preset target views, each with its own characteristics such as white balance and auto exposure
• Up to 127 preset target views, each with its own characteristics such as white balance and auto exposure.
• Up to eight swing actions between two preset positions
• Up to eight swing actions between two preset positions.
• Up to four patterns for moving the camera as if it were controlled by a joystick
• Up to four patterns for moving the camera as if it were controlled by a joystick.
• Up to eight group actions, each including up to a total of 20 presets, swing actions, and patterns
• Up to eight group actions, each including up to a total of 20 presets, swing actions, and patterns.
• Up to four privacy masks which can be increased or decreased in size to cover certain areas to
• Up to four privacy masks which can be increased or decreased in size to cover certain areas to
protect privacy
protect privacy.
Reserved Presets: Certain camera characteristics can be specified by using reserved preset configurations instead of
Reserved presets: Certain camera characteristics can be specified by using reserved preset configurations
individually configuring those characteristics.
instead of individually configuring those characteristics.
Standard PTZ Control: Works with Pelco-D or Pelco-P compatible controllers via an RS-485 connection.
Standard PTZ control: Works with Pelco-D or Pelco-P compatible controllers via an RS-485 cable.
Smart Power-Up: Resumes the last action executed before power to the camera was cut, including most preset, pattern,
Power Up Action: Resumes the last action executed before power to the camera was cut, including most
swing, and group actions.
preset, pattern, swing, and group actions, but not jog actions.
Auto-Flip: Vertically inverts the image if the camera tilts below its center.
Auto Flip: Vertically inverts the image if the camera tilts
Parking Action: Should no operator-activated or automated camera action occur during a specified time (programmable
Parking Action: Should no operator-activated or automated camera action occur during a specified time
from 1 minute to 4 hours), the camera automatically moves to a pre-determined preset position or any pre-programmed
(programm ble from 1 minute to 4 hours), the camera automatically moves to a pre-determined preset position.
pattern, swing, or automatic camera function.
Privacy Zone Mask: Up to four privacy masks can be created to cover certain areas or objects such as windows or private
Privacy Zone Mask: Up to four privacy masks can b created to cover cert in areas or objects uch as
houses. The masks can be adjusted for size. When the camera moves past such areas or objects, the mask automatically
windows or private houses. The masks can be adjust d for size. When the camera moves past such areas or
covers them.
objects, the mask automatically follows them.
Global or Local Image Setup: Determines how white balance and auto exposure settings are applied. When programmed
Global or Local Image Setup: Determines how white balance and auto exposure settings are applied. When
for "Global" setup, those settings are automatically applied to each preset location. Under "Local" setup, those settings are
programmed for "Global" setup, those settings are automatically applied to each preset location. Under "Local"
set separately for each preset location. The "Global" settings for white balance and auto exposure will be used during jog
setup, those settings are set separately for each preset location. The "Global" settings for white balance and
operations.
auto exposure will be used during jog operations.
Semi/Auto Focus: The focus for each preset location is manually set, and the camera automatically uses that focus when it
Semi/Auto Focus: The focus for each preset location is manually set, and the camera automatically uses that
moves to a preset location. During jog operations, the camera uses auto focus. The shift between semi-auto and auto focus
focus when it moves to a preset location. During job operations, the camera uses auto focus. The shift between
occurs automatically.
semi and auto focus occurs automatically.
3
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
a
Parts List:
1x Camera
1x Wall-mount bracket
1x Manual
4x Short screws (for attaching camera to bracket)
4x Long screws (for attaching bracket to wall)
1x Extension cord
Specifications:
EV-7105-NPEQ
EV-7105-PPEQ
Mini PTZ Camera
NTSC PAL
1/4” Interline Transfer
Color: 520 TV Lines / B/W: 570 TV Lines
768x494 pixels
1.0Vp-p composite video, 75Ω
Type
Video output format
CCD
Resolution
Pickup elements
752x582 pixels
Video output
Lens
F1.8, f=3.8~38mm
Color: 0.7 Lux / B/W: 0.02 Lux
Minimum Illumination
S/N Ratio
Zoom
50dB (AGC OFF)
x10 Optical / x10 Digital
Day and Night
Auto / Day / Night (ICR – removable IR cut filter)
Focus
Iris
Auto / Manual / Semi-Auto
Auto / Manual
Shutter Speed
AGC (AutomaticGain Control)
Sense-Up
1/60~1/120,000 s
Normal / High / Off
x2~x128
Auto / Manual (Red, Blue, Gain Adjustable)
Low / Middle / High / Off
White Balance
BLC (Back Light Compensation)
Selectable
Flickerless
Low / Middle / High / Off
SSNR (Noise Reduction)
RS-485
Communication
Protocol
Pelco-D, Pelco-P selectable
4 Zones
Privacy
OSD
Menu / PTZ information, etc.
Operating voltage
Power consumption
24VAC
20W
Indoor: 32~104° F (0~40° C) /
Operating temperature
Outdoor: -4~122° F (-20~50° C)
Dimensions
Weight
413/16” x7”x413/16” (122x180x122 mm)
2-lb 10-oz (1.2kg)
Pan/Tilt:
Pan
360°
180°
Range
Tilt
Preset
Manual
Swing
Up to 360°/s (programmable)
0.05~360°/s (proportional to zoom)
1~180°/s
Pan/Tilt
Speed
Presets
Patterns
Swings
Groups
Max. 127 presets (Label, Camera Image Setting)
Max. 4 patterns
Max. 8 swings
Max. 8 groups (20 actions/group)
Auto-Flip, Auto-Parking, Power Up Action, etc.
Other functions
a
4
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Dimensions:
Camera
Side
Bottom
6”
(152mm)
7”
(180mm)
413/16”
(122mm)
Wall-Mount Bracket
Side
Bottom
31/8”
(80mm)
411/16”
(119mm)
61/2”
(166mm)
5
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Safeguards and Precautions
Before Starting:
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not point the camera at the sun. Heat could damage the camera, even when not in use.
4. Do not expose the camera to rain or moisture.
5. Do not install the camera in dusty or humid environments.
6. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
7. Do not open or disassemble the camera. There are no field-serviceable parts inside.
8. Do not drop the camera or subject it to strong vibrations.
9. This camera is VERY HEAVY. To prevent injury to the installer and client, do not mount it on an unstable or improperly
supported surface. When mounting, only use brackets or other mounting devices that are recommended in this manual.
Operation Precautions:
1. Only use regulated power supplies with voltage and minimum current output per the specifications of this camera.
2. If the camera gets hot or starts smoking while in use, disconnect the power immediately and contact the professional
installer or dealer.
Cleaning Precautions:
1. Periodically clean the dust off the entire camera with a slightly damp (NOT WET) cloth. DO NOT USE
chemical cleaners.
2. Do not move the camera while cleaning, as this could change the angle of the view.
3. If the dome cover becomes dusty, carefully clean using a slightly slightly damp (NOT WET) cloth. DO NOT USE
chemical cleaners. DO NOT SCRATCH the dome, as this will hurt the quality of the video image.
6
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
a
Overview
Wall mount
bracket
Camera
DIP switches
Lens
Turn counter-clockwise
to remove
Dome
7
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
a
Communication Protocol and Camera ID DIP Switch Setup:
Before the Mini PTZ Camera is installed, first set up the DIP switches to configure the camera ID and the
communications protocol.
Communication Protocol
Camera ID
1. Remove the clear dome of the Mini PTZ Camera by turning it counterclockwise by hand.
2. Look for the two DIP switch blocks near the base of the black plastic dome which surrounds the camera. DO
NOT REMOVE THE BLACK PLASTIC DOME.
3. Set the camera ID (8- pin DIP switch):
– The camera ID is a binary number from 1 to 255. Factory default camera ID is "1."
– Do not use "00000000" as a camera ID.
– The ID number of a particular camera must match the Cam ID setting of the DVR or keyboard controller.
Example: Camera ID=5
Example: Camera ID=10
On
On
1
1
1
2
2
+
3
4
4
4
8
=
5
6
7
8
1
1
2
2
2
3
4
+
4
8
8
5
6
7
8
16 32 64 128
16 32 64 128
Value
Value
5
=
10
4. Set the communication protocol
(4- pin DIP switch):
– Set the proper protocol using Pin 1 and
Pin 2 of the 4-pin DIP switch.
– The protocol for the camera must be
identical to the protocol used by the DVR
or pan/tilt controller. If not, the camera
cannot be controlled by the controller. See
the DVR or pan/tilt controller
manual for protocol information.
– If the protocol of the camera is changed,
the camera must be turned off and then
turned back on for the change to take
effect.
– The factory default protocol is
"Pelco-D, 2400 bps."
– Pins 3 and 4 are set by the factory and
must not be changed. If they are changed,
the camera WILL NOT OPERATE
PROPERLY.
DO NOT TOUCH
PINS 3 AND 4
8
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
a
Installation
1. Connect the camera to either the included wall mount or other optional bracket.
2. Run a 24VAC power supply wire, a video cable with a male BNC connector, and a data wire through the
wall to where the camera is to be mounted.
3. Connect the camera's video cable to the video cable coming from the wall. Do not cut the female BNC
connector of the camera's video cable as that will void the warranty.
4. Connect the camera's RS-485 cable to the data wire cable coming from the wall.
Note: If necessary, use the included extension cable for more convenient wiring.
5. Temporarily connect the camera to the power supply. Do not cut the AC power terminal of the
camera's power cable as that will void the warranty.
6. Hold the camera's bracket against the wall or ceiling where it is expected to be mounted, but do not mount
yet. While watching the monitor, operate the camera's pan and tilt functions to ensure that this mounting
location is correct. Use a pencil to mark the location of the screw holes in the mounting bracket.
7. Disconnect the power supply from the camera.
8. Mount the mounting bracket to the wall or ceiling using the included mounting screws. If the wall is made
of drywall, brick, or similar material, it may be necessary to use the included screw anchors.
9. Reconnect the camera's power supply.
10. Program the camera via the on-screen display (OSD) menus from the DVR or keyboard controller.
11. Do a final test of the video camera and monitor.
Basic Installation
24VAC Jack
Video coaxial cable
RS-485 (+) (Orange)
RS-485 (-) (Yellow)
Connecting Multiple PTZ Cameras
DR-1 Series DVR
9
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
a
Pre-operation Checklist
Before operating this PTZ camera, please note the following:
Double-check that the cables are properly run between the controller and camera, and that all connections are
correct.
Double-check that the camera ID on the controller is the same as the ID of the target camera. The camera ID can
be found by looking at the camera ID DIP switch settings (see page 8).
The Pelco protocol setting of the controller and the camera must be identical. The Pelco protocol setting of the
camera can be found by looking at the communication protocol setup DIP switch settings (see page 8).
Make sure that the camera was rebooted after any of the camera ID or communication protocol setup DIP
switches are changed.
Refer to the controller or DVR manual for information on configuring or operating those devices.
10
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Understanding and Operating Preset and Pattern Functions
Standard Pelco-compatible controllers allow the camera operator to do several functions without going through
the full OSD menu, depending on the capabilities of the DVR to which the camera is connected.
The SECO-LARM series of DVRs allows operators to do the following via the "Dome Preset" menu:
•
•
•
•
Set the camera to remember multiple specific preset locations.
Tell the camera to go to a specific preset location.
Run certain preset functions, including patterns, swings, or grouped functions.
Change certain configuration patterns.
Programming the patterns, swings, or grouped functions, and detailed configuration of the PTZ camera,
requires operators to use the OSD menu. See page 16 for more information.
This PTZ camera can be controlled by any DVR or keyboard controller which uses Pelco-compatible protocols.
When using non-SECO-LARM DVRs, or when using keyboard controllers, the manuals for those devices may
include information on how to operate or program the PTZ camera.
To set or go to a Preset location or use a preset function via a SECO-LARM DVR:
1. Press the "Dome" key. The lower left corner of the screen will change from "REC" to "DOME" to show the
camera is in the Dome Control menu.
2. Press the "1" key to go to the DOME PRESET menu.
3. Use the UP, DOWN, LEFT, and RIGHT buttons to highlight your selection and push ENTER to confirm
your selection.
Note: In most cases, only the GO function will work. Only the preset locations can be programmed via
the DOME PRESET menu. Other functions must be programmed using the OSD menu.
4. Use the UP and DOWN arrows to switch between YES and NO. Go to YES, and press the ENTER key.
See page 13 for a list of preset functions.
11
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Configuring Mini PTZ Camera settings with an ENFORCER DR-1 Series DVR
Step 1
Press Dome on the DVR front panel to access
DVR controls.
Step 2
Press 1 to access the DVR preset menu
Step 3
Use the Up, Down, Left, Right, and Enter
buttons to make a selection.
Step 4
Go to Preset 95 to access Mini PTZ OSD settings.
This will bring up the SPEED DOME CAMERA menu as shown on page 18.
12
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Reserved Presets
<Go Preset> [95]
:Enters into OSD menu
<Go Preset> [131~134]
<Go Preset> [141~148]
<Go Preset> [151~158]
<Go Preset> [170]
<Go Preset> [171]
<Go Preset> [174]
<Go Preset> [175]
:Runs Pattern Function 1~4
:Runs Swing Function 1~8
:Runs Group Function 1~8
:Sets Camera BLC mode to OFF
:Sets Camera BLC mode to ON
:Sets Camera Focus mode to AUTO
:Sets Camera Focus mode to MANUAL
:Sets Camera Focus mode to
SEMI-AUTO
<Go Preset> [176]
<Go Preset> [177]
<Go Preset> [178]
<Go Preset> [179]
<Go Preset> [190]
<Go Preset> [191]
<Go Preset> [192]
<Go Preset> [193]
<Go Preset> [194]
:Sets Day and Night mode to AUTO
:Sets Day and Night mode to NIGHT
:Sets Day and Night mode to DAY
:Sets OSD Display mode to AUTO (Except Privacy Mask)
:Sets OSD Display mode to OFF (Except Privacy Mask)
:Sets OSD Display mode to ON (Except Privacy Mask)
:Sets all Privacy Mask Display to OFF
:Sets all Privacy Mask Display to ON
Configuration Defaults
Default Display Configuration
Default Camera Configuration
Camera ID
PTZ Information
Action Title
Preset Label
Alarm Input
North Direction
Privacy Zone
ON
Focus Mode
Digital Zoom
Line Lock
White Balance
Backlight
Day & Night
Brightness
Iris
SEMI-AUTO
ON
OFF
AUTO
OFF
AUTO1
25
AUTO
AUTO
AUTO
AUTO
AUTO
Pan 0˚
Undefined
Default Motion Configuration
Shutter
ESC
Motion Lock
Power Up Action
Auto Flip
OFF
ON
ON
AGC
SSNR
SENS-UP
NORMAL
MIDDLE
AUTO (4 Frame)
Jog Max Speed
Jog Direction
Freeze In Preset
Park Action
120˚ / sec
INVERSE
OFF
OFF
OFF
User Edit Data
Preset 1~94, 96~128
Swing 1~8
Pattern 1~4
Group 1~8
Undefined
Undefined
Undefined
Undefined
Alarm Action
13
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
OSD Display of Main Screen
Preset
Label
Action Title
Alarm
Information
Image Flip
Camera ID
Pan/Tilt/Zoom
Information
OSD Main Screen
The OSD main screen shows information about the current situation of the camera while it is operating. This screen is NOT
seen as part of the programming process.
Preset Label
Action Title
The label of the specific preset.
Will be one of the following:
SET PRESET XXX
PRESET XXX
PATTERN X
SWG X / PRESET XXX
UNDEFINED
When PRESET XXX is stored
When camera reaches PRESET XXX
When PATTERN X is in action
When SWING X is in action
When an undefined function is called
Image Flip
Camera ID
Shows that the image is currently flipped vertically by the Auto Flip function
Shows the current camera ID (address)
Alarm Information
This function is reserved for future use
Current Pan/Tilt/Zoom information (4 information points):
Pan angle in degrees
Tilt angle in degrees
P/T/Z Information
Zoom level
Compass direction
Example: (15 / 4 / x 1 / N) means a Pan angle of 15 degrees, a Tilt angle of 4
degrees, Zoom (magnification) level of 1 (100%), and camera facing "North."
14
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Operating the OSD Menus
For operating the OSD menus, please note the following:
• To access the OSD menu from your DVR, go to Preset 95. For more information on DVR presets and their
functions for the ENFORCER Mini PTZ Camera, please see page 13, Reserved Presets.
• Most commands are done on PELCO-compatible DVRs using the front panel keys, including the up, down,
right, and left arrows, or via a panel-mounted joystick. Such operations may also be possible using the
DVR’s remote control.
Note: For ENFORCER DR-1 DVRs, the operations are usually done using the DVR remote control.
• For many menu operations, the user must press the SEQ or FREEZE keys. For most DVRs, these are the
keys for focus in (SEQ) and focus out (FREEZE), but may be marked with other words.
For ENFORCER DR-1 Series DVRs, the operations are done using:
o Menu items which have sub-menus are surrounded by “<” and “>” brackets
(For example, <DISPLAY SETUP>).
o To enter a sub-menu, press the SEQ key.
o To go up one level, press the FREEZE key.
o To move from item to item in a menu, use the arrow keys or joystick to move up/down or left/right.
o To change the value of an item, use the arrow keys or joystick to move up/down or right/left.
o To save a value, press the SEQ key.
o To cancel a value or operation, press the FREEZE key.
SEQ and FREEZE keys
15
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
ENFORCER Mini PTZ Camera
OSD (On-screen Display) and Programming Flowchart
This chart shows all the screens used in programming the PTZ camera using the OSD.
To go to a particular screen, follow the order as shown in this flowchart.
OSD Main
Screen
(page 14)
For more information on a particular screen, go to the page number listed on the screen.
SPEED DOME
CAMERA
(page 18)
SYSTEM
INFORMATION
(page 18)
DISPLAY
SETUP
(page 19)
DOME CAMERA
SETUP
SYSTEM
INITIALIZE
(page 32)
(page 21)
SET NORTH
DIRECTION
(page 19)
PRIVACY ZONE
(page 20)
EDIT MASK
(page 20)
ZOOM
CAMERA
SETUP
MOTION
SETUP
(page 24)
PATTERN
SETUP
(page 29)
GROUP
SETUP
(page 30)
PRESET MENU
(page 26)
SWING SETUP
(page 28)
(page 22)
WHITE
BALANCE
SETUP
AUTO
EXPOSURE
SETUP
PARKING
ACTION SETUP
ALARM INPUT
SETUP
(reserved)
EDIT SCENE
(page 27)
EDIT LABEL
(page 27)
EDIT PATTERN
(page 29)
EDIT GROUP
(page 30~31)
(page 25)
(page 22)
(page 23)
16
SECO-LARM, U.S.A., INC.
17
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
SPEED DOME CAMERA Menu
SPEED DOME CAMERA
•
•
<SYSTEM INFORMATION>: Displays system information
and configuration (see menu on page 18).
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
EXIT
<DISPLAY SETUP>: Configures the display information
shown on the OSD Main Screen as shown on page 16 (see
menu on page 19).
•
•
<DOME CAMERA SETUP>: Configures various functions of
the camera (see menu on page 21).
<SYSTEM INITIALIZE>: Initializes system configuration and
sets all data to factory default configuration (see menu on
page 31).
SYSTEM INFORMATION Menu
From SPEED DOME CAMERA
This menu shows the current configuration information as
configured on page 8. No information can be programmed using
this OSD menu.
SYSTEM INFORMATION
FIRMWARE VER : V2.0
COLOR SYSTEM : NTSC
PROTOCOL
ADDRESS
: PELCO-D
: 38
BAND RATE
: 9600
BACK
EXIT
18
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
DISPLAY SETUP Menu
From SPEED DOME CAMERA
DISPLAY SETUP
This menu enables or disables the information shown on the
OSD Main Screen (see page 14).
CAMERA ID
: ON
PTZ INFORMATION : AUTO
ACTION TITLE
PRESET LABEL
ALARM INPUT
: AUTO
: AUTO
: AUTO
Note that setting an item to "AUTO" means that item will be
displayed only when its value changes.
<SET NORTH DIRECTION>
<PRIVACY ZONE>
This menu accesses other OSD menus for configuring a specific
pan direction of the camera as "NORTH" for certain functions,
and for setting privacy zones.
BACK
EXIT
CAMERA ID
[ON/OFF]
PTZ INFORMATION
ACTION TITLE
PRESET LABEL
[ON/OFF/AUTO]
[ON/OFF/AUTO]
[ON/OFF/AUTO]
[AUTO] -- This function is
reserved for future use.
ALARM INPUT
<SET NORTH DIRECTION> See OSD menu below.
<PRIVACY ZONE> See OSD menu on page 20.
SET NORTH DIRECTION Menu
From DISPLAY SETUP
SET NORTH DIRECTION
This menu sets a specific pan and tilt location as "compass
north," or a certain location on which other functions are
centered.
Using the arrow keys or joystick, point the camera towards the
default location, and then select "NEAR" or "SAVE" to configure
that location as "compass north."
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
19
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
PRIVACY ZONE Menu
From DISPLAY SETUP
This menu configures an area of the camera’s field of vision so
that it is covered by a gray mask, hiding it. For instance, this
would be used to cover a neighbor’s window, or a sensitive
window of the office.
PRIVACY ZONE
MASK NO
1
UNDEFINED
OFF
CANCEL
DISPLAY
CLEAR MASK
<EDIT MASK>
Once configured, the gray mask automatically appears over that
area every time the camera pans or tilts past it.
BACK
EXIT
1~4. Select the mask number. If that mask
was already configured, the camera will
MASK NO
DISPLAY
move to the where it was set. Otherwise,
UNDEFINED will be displayed under
MASK NO.
[ON/OFF] Shows ON if the selected mask
is active, shows OFF if that mask is not
active.
CLEAR MASK Deletes data in the selected mask.
<EDIT MASK> See EDIT MASK menu below.
EDIT MASK Menu
From PRIVACY ZONE
Move the camera to the target area to be masked and choose
NEAR or SAVE. The mask will be displayed as a gray square.
EDIT MASK 1
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
Once the mask is displayed:
EDIT MASK 1
•
•
•
Center the camera on the object to be masked.
Use the joystick or arrow keys to adjust the mask size.
Select "NEAR" or "SAVE" to save the mask setting.
[ ◄►: ADJUST MASK WIDTH]
[ ▲▼: ADJUST MASK HEIGHT]
[NEAR:SAVE /FAR:CANCEL]
20
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
DOME CAMERA SETUP Menu
From SPEED DOME CAMERA
Goes to the ZOOM CAMERA SETUP menu
for configuring many of the general functions
of the zoom camera module. See page 22.
Configures the general functions of the pan
and tilt motions. See page 24
Configures up to 127 different preset
locations to which the camera can be
instantly moved. See page 26.
DOME CAMERA SETUP
<CAMERA SETUP>
<MOTION SETUP>
<PRESET SETUP>
<CAMERA SETUP>
<MOTION SETUP>
<PRESET SETUP>
<SWING SETUP>
<PATTERN SETUP>
<GROUP SETUP>
BACK
EXIT
Configures up to four different swing motions
between two different preset locations. See
page 28.
<SWING SETUP>
Configures up to four pan/tilt patterns, with
each pattern consisting of a starting position,
an ending position, and the complete
pan/tilt/halt movement between those two
points. See page 29.
<PATTERN SETUP>
Configures up to eight groups of motions,
with each group consisting of any
combination of up to 20 presets, swings,
patterns, and temporary halts in the action.
See page 30.
<GROUP SETUP>
21
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
ZOOM CAMERA SETUP Menu
From DOME CAMERA SETUP
This menu configures many of the general functions of the zoom camera module.
ZOOM CAMERA SETUP
FOCUS MODE SEMI-AUTO
DIGITAL ZOOM ON
LINE LOCK
IMAGE FLIP
OFF
OFF
<WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
BACK
EXIT
[AUTO / MANUAL / SEMI-AUTO]
Sets the camera focus mode.
"SEMI-AUTO" mode -- In this mode, the camera switches between the
"manual focus mode" and "auto focus mode" depending on the current
operation of the camera. When the camera moves to a PRESET location, the
focus of the camera changes to the focus that was memorized when the
PRESET was configured ("manual focus mode"). During jog operations, the
camera switches to auto focus ("auto focus mode").
[ON / OFF] Sets the digital zooom function ON or OFF. If set to "OFF" the
maximum zoom of the camera is the optical zoom. If set to "ON" the digital
zoom operates when the optical zoom reaches its maximum setting.
[ON / OFF] If set to ON, the camera's line lock sync is synchronized with the
AC power. This function might be used if multiple cameras attached to the
same DVR interfere with each other.
FOCUS MODE
DIGITAL ZOOM
LINE LOCK
IMAGE FLIP
[ON / OFF] When ON, the camera image flips up-side-down.
In the manual mode, the red and blue color levels can be configured manually.
See below.
<WHITE BALANCE SETUP>
<AUTO EXPOSURE
SETUP>
Configures a variety of lighting settings for the camera. See page 23.
WB SETUP Menu (White Balance)
From ZOOM CAMERA SETUP
This menu allows the red and blue color levels to be adjusted automatically
or manually.
WB SETUP - GLOBAL
WB MODE
AUTO
RED ADJUST
BLUE ADJUST
_ _ _
_ _ _
[AUTO / MANUAL] In the manual mode, the red and
blue colors can be individually set.
WB MODE
RED ADJUST
BLUE ADJUST
[10~60]
[10~60]
BACK
EXIT
22
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
AE SETUP Menu (Auto Exposure)
From ZOOM CAMERA SETUP
[ON / OFF]
AE SETUP - GLOBAL
BACKLIGHT
DAY/NIGHT
Sets the backlight compensation.
[AUTO1 / AUTO2DAY / NIGHT]
AUTO1 flips between the day and night
modes faster than AUTO2.
[0~100]
BACKLIGHT
DAY/NIGHT
BRIGHTNESS
IRIS
SHUTTER
AGC
OFF
AUTO
25
AUTO
ESC
NORMAL
MIDDLE
AUTO
SSNR
SENS-UP
Adjusts the brightness of the image. The
BRIGHTNESS IRIS, SHUTTER, and gain settings are all
adjusted automatically as the
BACK
EXIT
BRIGHTNESS is adjusted.
[AUTO / MANUAL (0~100)]
If IRIS is set to AUTO, the IRIS of the
camera is set automatically according to
the SHUTTER, which should be manually
IRIS
set.
If IRIS is set to MANUAL, the IRIS setting
should be manually set while the
SHUTTER is set to ESC or A.FLICKER.
[ESC / A.FLICKER / MANUAL]
(x1/60~1/120,000 sec.)
If IRIS is set to MANUAL and SHUTTER
is set to ESC (electronic shutter control),
the SHUTTER is automatically set
according to the IRIS setting.
Set SHUTTER to A.FLICKER (flickerless)
to automatically compensate for CFL light
flicker. If interference from CFL light flicker
persists, set the SHUTTER to 1/100-
second for NTSC or 1/120-second for PAL
systems.
SHUTTER
If SHUTTER is to be set manually, set
IRIS to MANUAL.
[OFF / NORMAL / HIGH]
AGC (auto gain control) enhances the
camera image brightness automatically if
the light level of the image is too low.
[OFF / LOW / MIDDLE / HIGH]
AGC
SSNR noise reduction enhances images
by reducing signal noise when the gain
level of the image is too high.
SSNR
[AUTO (2~128) / OFF]
When set for AUTO, the SHUTTER is
automatically adjusted so that multiple
frames are combined into a single frame
in low-light conditions. For instance, when
set to "8" the images from eight frames
are combined into one frame to increase
the light level. However, this also creates
"ghost" images.
SENS-UP
23
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
MOTION SETUP Menu
From DOME CAMERA SETUP
Configures the general functions of the pan and tilt motions.
MOTION SETUP
MOTION LOCK
OFF
PWR UP ACTION ON
AUTO FLIP ON
JOG MAX SPEED 120/SEC
JOG DIRECTION INVERSE
FRZ IN PRESET
OFF
<PARKING ACTION SETUP>
<ALARM INPUT SETUP>
BACK
EXIT
[ON / OFF]
If ON, the user is prevented from configuring or deleting
PRESET, SWING, PATTERN, or GROUP settings.
However, those settings can still be used during
operations. If OFF, the user is allowed to configure or
delete those settings using the OSD menu.
[ON / OFF]
MOTION LOCK
When ON, if power is unexpectedly cut to the camera
and restored, the camera continues to operate the last
action that was being performed before power was cut.
This includes most PRESET, SWING, PATTERN, or
GROUP actions.
PWR UP ACTION
AUTO FLIP
[ON / OFF]
If ON, the image is automatically vertically flipped when
the camera tilts below its center.
(1°/sec.~360°/sec.)
This sets the maximum jog speed, which is the pan and
tilt speed of the camera when operated by the user. The
jog speed is also automatically adjusted according to the
camera's zoom. As the zoom level increases, the pan
and tilt jog speed decrease.
JOG MAX SPEED
JOG DIRECTION
[INVERSE / NORMAL]
This determines whether the controls will be inverse or
normal when operating the pan and tilt of the camera.
[ON / OFF]
If the Freeze in Preset function is turned ON, the on-
screen camera image at the beginning of a PRESET
action is frozen while the camera moves from the
starting position to the ending position, as programmed
by the user. If turned OFF, the on-screen camera image
moves as the camera moves from the starting to ending
position
FRZ IN PRESET
Determines what the camera will do if it receives no PTZ
command during a preset time. See page 25.
<PARKING ACTION SETUP>
<ALARM INPUT SETUP>
This is a reserved function, and is currently not available
24
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
PARKING ACTION SETUP Menu
From MOTION SETUP
This menu sets what the camera will do if it receives no PTZ
command during a preset time.
PARKING ACTION SETUP
PARK ENABLE OFF
WAIT TIME
00:10:00
PARK ACTION HOME
[ON / OFF]
If set to ON, the camera runs an assigned
PARK ENABLE
WAIT TIME
function automatically if there is no PTZ
command during the configured "WAIT TIME.”
[1 minute to 4 hours]
The time the PTZ camera waits before running
the assigned function can be set by the number of
minutes. This time is displayed in the "hh:mm:ss"
format
BACK
EXIT
[HOME / PRESET / PATTERN / SWING /
GROUP]
• HOME — Camera moves to the
"HOME" position
• PRESET — Camera moves to the specified
"PRESET" position
PARK ACTION
• PATTERN — Camera performs the specified
"PATTERN" action
• GROUP — Camera performs the specified
"GROUP" action
Note: The PRESET, PATTERN, or GROUP
option requires the input of which position
or action is to be done.
25
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
PRESET MENU
From DOME CAMERA SETUP
This menu configures up to 127 different preset locations to
which the camera can be instantly moved.
PRESET MENU
PRESET NO.
1
CLR PRESET
<EDIT SCENE>
<EDIT LABEL>
CAM ADJUST
CANCEL
[1~94, 96~128]
If the PRESET number has already been
defined, the camera immediately moves
to the pre-set PRESET position and
characteristics. If not, "UNDEFINED" is
shown on the screen
GLOBAL
BACK
EXIT
PRESET NO.
Note: If a PRESET position is already
defined, the user can make
changes by selecting that
PRESET position number and
then changing the SCENE,
LABEL, and CAM ADJUST
settings.
[CANCEL / ON]
CLR PRESET
Choose "CANCEL" to delete the current
PRESET data.
Redefines the current PRESET scene
position. See page 27
<EDIT SCENE>
Allows user to display a note about this
preset position when the camera moves
to the PRESET position, up to a
maximum of 10 characters.
<EDIT LABEL>
CAM ADJUST
[GLOBAL / LOCAL]
This sets the WB (white balance) and AE
(auto exposure) modes. "GLOBAL" mode
means that the WB and AE settings for
all PRESET positions are the same as
configured in the WB SETUP menu
under the ZOOM CAMERA SETUP menu
(see page 22). "LOCAL" mode means
that each PRESET position has its own
WB and AE settings
NOTE: The <EDIT LABEL> and CAM ADJUST screens are
not visible unless the <EDIT SCENE> function
is selected.
26
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
EDIT SCENE Menu
From PRESET MENU
EDIT SCENE – PRESET 1
This menu redefines the current PRESET scene position.
1.
2.
Use the joystick or arrow keys to move the camera to the
desired position.
Press the "NEAR" key to save the new camera position, or
press the "FAR" key to cancel this position.
MOVE TO TARGET POSITION
[NEAR : SAVE /FAR: CANCEL]
EDIT LABEL Menu
From PRESET MENU
EDIT LABEL – PRESET 1
This menu allows the user to display a note about this PRESET
position every time the camera moves to the position, up to a
maximum of 10 characters.
[ █
]
------------------------------
1 2 3 4 5 6 7 8 9 0
OK
A B C D E F G H I J K CANCEL
L M N O P Q R S T U
V W X Y Z a b c d e g
1.
The reverse-color rectangle serves as the cursor for the
message, while a rectangle box shows the character to be
chosen.
h i j k l m n o q r s t u
v w x y v < > - / : .
←
EDIT LABEL – PRESET 1
[ █
]
Current Cursor Location
2.
Using the joystick or the arrows, move the rectangular box
to highlight the appropriate character. Press the "NEAR"
key to add that character to the message.
Note: To delete a character, choose the back arrow.
-----------------------------
1 2 3 4 5 6 7 8 9 0
OK
A B C D E F G H I J K CANCEL
L M N O P Q R S T U
V W X Y Z a b c d e g
h i j k l m n o q r s t u
v w x y v < > - / : . ←
Character to
be chosen
Space
Back Space
3.
Press the "NEAR" key to save the new label, or press the
"FAR" key to cancel this label.
27
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
SWING SETUP Menu
From DOME CAMERA SETUP
This menu configures up to eight different swing motions back and forth
between two different PRESET positions.
SWING SETUP
SWING NO.
1ST POS.
2ND POS.
1
NOT USED
NOT USED
When the SWING function operates, the camera moves (pans and tilts) to
the PRESET position that was set as the "1ST POS." and then moves
clockwise to the PRESET position set as "2ND POS." At that point, the
camera moves counterclockwise back to the "1ST POS." It then repeats
that motion back and forth between the two PRESET positions until another
command is inputted.
SWING SPEED 30/SEC
CLEAR SWING CANCEL
BACK
EXIT
[1 ~ 8]
Selects which SWING motion to edit. Choose 1
SWING NO.
1ST POS.
through 8. If a selected SWING motion has not
been defined, "NOT USED" is displayed in the first
and second positions for that motion
[PRESET 1 ~ 94 or 96 ~ 128]
EDIT LABEL – PRESET 1
SWING NO.
1ST POS.
2ND POS.
1
PRESET 5
NOT USED
UNDEFINED
[PRESET 1 ~ 94 or 96 ~ 128]
Select the two PRESET positions between which
the SWING motion will operate. NOTE -- If a
selected PRESET was not previously defined via
the OSD programming, "UNDEFINED"
will be displayed.
2ND POS.
Programs the speed at which the camera moves,
between the two PRESET positions.
[CANCEL / OK]
Choose “OK” to delete the data in the selected
SWING.
SWING SPEED
CLEAR SWING
28
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
PATTERN SETUP Menu
From DOME CAMERA SETUP
PATTERN SETUP
Configures up to four pan/tilt patterns, with each pattern consisting of a
starting position, an ending position, and the complete pan/tilt/halt movement
between those two points .
PATTERN NO.
1
UNDEFINED
CLR PATTERN CANCEL
<EDIT PATTERN>
[1 ~ 4]
Selects which PATTERN number to edit. If the
PATTERN NO
CLR PATTERN
selected PATTERN number has not yet been
programmed, "UNDEFINED" will be displayed
under the selected PATTERN number.
[CANCEL / OK]
Choose "OK" to delete the data in the selected
PATTERN
BACK
EXIT
<EDIT PATTERN> Goes to the "EDIT PATTERN" menu. See below.
EDIT PATTERN Menu
From PATTERN SETUP
EDIT PATTERN 1
1. Use the joystick or arrow keys to move the camera view to the
appropriate starting position for the pattern, and set the
desired zoom.
To start the pattern recording, press the NEAR key. To exit this
menu without saving the pattern, press the FAR key.
MOVE TO START POSITION
[NEAR:START /FAR:CANCEL]
2.
Use the joystick or arrow keys to move the camera along the
desired path until the end. As the camera is moving, the path
is being saved into its memory.
EDIT PATTERN 1
Note: While setting the PATTERN, any time the camera
pauses will also be saved as part of the pattern.
The total memory size and available memory is displayed on
the screen as a bar.
[NEAR:SAVE /FAR:DELETE]
0 / 0 / x 1 / N
3.
To save this pattern, press the NEAR key. To cancel the
recording of the PRESET pattern, press the FAR key.
29
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
GROUP SETUP Menu
From DOME CAMERA SETUP
GROUP SETUP
Configures up to eight groups of motions, with each group
consisting of any combination of up to 20 actions, including
PRESETS, SWINGS, PATTERNS, and temporary halts in
the action.
GROUP NO.
1
UNDEFINED
CLEAR GROUP CANCEL
<EDIT GROUP>
[1 ~ 4]
Selects which GROUP number to edit. If
the selected GROUP number has not yet
been programmed, "UNDEFINED" will be
BACK
EXIT
GROUP NO
displayed under the selected GROUP
number
[CANCEL / OK]
CLR GROUP
Choose "OK" to delete the data in the
selected GROUP
Goes to the "EDIT GROUP" menu. See
below
<EDIT GROUP>
EDIT GROUP 1
1.
2.
3.
Press the NEAR key on the "NO" line to start the
GROUP setup.
NO ACTION ### DWELL OPT
NONE
NONE
1
2
3
4
5
NONE
NONE
NONE
SAVE
CANCEL
[NEAR:EDIT]
Use the joystick or arrow keys to move up and down to
select the number of the ACTION to configure. There are
a maximum of 20 ACTIONS which can be done in
each GROUP.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1
2
3
4
5
NONE
NONE
NONE
NONE
NONE
SAVE
CANCEL
[NEAR:EDIT ACT]
[FAR : EDIT :END]
Set the ACTION, DWELL time, and OPT (option) for each
action. The item ready for configuring is displayed in
reverse text. Move the joystick/arrow cursor right and left to
select items to configure, and then move the joystick/arrow
cursor up and down to change the value of the ACTION.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1
2
3
4
5
NONE
NONE
NONE
NONE
NONE
ACTION ###
DWELL
[NONE / PRESET / SWING / PATTERN]
[0 seconds ~ 4 minutes]
SAVE
CANCEL
[◄►:MOVE CURSOR]
[▲▼:CHANGE VAL.]
NOTE — DWELL configures how long the
camera waits between each ACTION.
Option. If PRESET is selected as the
ACTION, this will be the PRESET speed.
If PATTERN or SWING is selected as the
ACTION, set OPT for the number of times
the PATTERN or SWING is repeated.
OPT
30
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
4.
Configure each ACTION, ###, DWELL, and OPT.
EDIT GROUP 1
NO ACTION ### DWELL OPT
In the sample screen on the left, ACTION #1 is the
command for the PTZ camera to go to PRESET #1 using
the PRESET speed of 360 as programmed in the PRESET
SETUP menu (see page 26), and stay at that position for 3
seconds before moving to the next action.
1
2
3
4
5
PRESET 1 00 : 03 : 360
NONE
NONE
NONE
NONE
SAVE
CANCEL
[◄►:MOVE CURSOR]
[▲▼:CHANGE VAL.]
5.
After setting up an ACTION, use the NEAR key to move the
cursor to the NO column, and then move the cursor up and
down to select another ACTION to configure or modify.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1
2
3
4
5
PRESET 1 00 : 03 : 360
NONE
NONE
NONE
NONE
SAVE
CANCEL
[NEAR:EDIT ACT]
[FAR : EDIT :END]
6.
After setting up all the ACTIONs for this GROUP, press the
FAR key to exit. At this point, the cursor will move to SAVE.
Press the NEAR key to save the data.
EDIT GROUP 1
NO ACTION ### DWELL OPT
1
2
3
4
5
PRESET 1 00 : 03 : 360
NONE
NONE
NONE
NONE
SAVE
CANCEL
SYSTEM INITIALIZE Menu
From SPEED DOME CAMERA
This menu lets the user clear selected programmed data, clear all
programmed data, or reboot the entire camera or system.
SYSTEM INITIALIZE
CLEAR ALL DATA
•CLR DISPLAY SET
•CLR CAMERA SET
•CLR MOTION SET
•CLR EDIT DATA
NO
NO
NO
NO
NO
NO
NO
Deletes all user-programmed data including
CLEAR ALL DATA
DISPLAY SETUP, CAMERA SETUP, and
MOTION SETUP.
REBOOT CAMERA
REBOOT SYSTEM
Clears the DISPLAY SETUP data and initializes
the configuration of that data.
Clears the CAMERA SETUP data and initializes
the configuration of that data.
Clears the MOTION SETUP data and initializes
the configuration of that data.
• CLR DISPLAY SET
• CLR CAMERA SET
• CLR MOTION SET
SAVE
EXIT
Deletes all PRESET SETUP data, SWING SETUP
data, PATTERN SETUP data, and GROUP
SETUP data.
• CLR EDIT DATA
REBOOT CAMERA
REBOOT SYSTEM
Reboots the zoom camera module.
Reboots the entire PTZ camera.
31
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Mini PTZ Camera
Also Available from SECO-LARM:
Ceiling
Pole-Mounting
Bracket
Corner-Mounting
Bracket
Flush-Mount
Bracket
DR-1 Series
Digital Video Recorder
Bracket
EV-7100CEILM
EV-7100POLEM
EV-7100CORNM
EV-7100FLUSM
DR-116-1.0TQ
Data
Distributor
RS-232 to RS-485
Converter
Passive
Video Balun
Passive
Video/Power/Data Balun
AC Power
Supply
RD-304-D1Q
EVA-RS1
EVT-PB1Q
EVT-PB1-31RQ
EVP-1SA8P16UL
IMPORTANT
Users and installers of this product are responsible for ensuring that use of this product complies with all national, state, and
local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do
not open the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
Website: www.seco-larm.com
E-mail: [email protected]
PISCN4
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
MiEV-7105-NPEQ_1111.docx
32
SECO-LARM, U.S.A., INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|