NVD Bullet Cameras
Installation Manual
3 Cameras in 1:
EV-1626-NKGQ (NTSC)
2.8~12mm
EV-1626-PKGQ (PAL)
EV-1626-NWGQ (NTSC)
EV-1626-PWGQ (PAL)
6~50mm
1/3” Sony Super HAD CCD
12VDC/24VAC
OSD with service monitor port
600 TV lines
NVD Bullet Cameras have an ultra-low lux rating of 0.000006 allowing the
camera to see in almost total darkness.
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Download from Www.Somanuals.com. All Manuals Search And Download.
NVD Bullet Cameras
Overview:
Connect service
monitor port connector
to service monitor port
A. Camera
B. Adjustable sunshield
C. Mounting plate
D. Camera base
E. Hex screws
F. Mounting screws
G. Focus
C
F
D
E
H. Zoom
B
I. Service cover
J. Female BNC
connector
OSD joystick
(video out)
K. DC jack
L. DC plug with
terminal block
I, M
Important:
H
G
J
Do not cut DC jack (K) or
female BNC connector (J) as
warranty will be voided.
A
M. Service monitor port,
OSD joystick
K
L
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
6. Do not open or disassemble the camera. There are
no field-serviceable parts inside.
2. Use the camera within given temperature and
7. Do not drop the camera or subject it to
strong vibrations.
electrical limits.
3. Do not aim the LEDs directly at the eyes when the
LEDs are on.
1Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or
during de-Gaussing, which occurs automatically
with many monitors when turning on.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.1
Installation:
1. Run a 12VDC or 24VAC power supply wire and a
6. Mount the mounting plate to the wall or ceiling using
the four included mounting screws. If the
wall is made of drywall, brick, or similar material,
it may be necessary to use screw anchors
(not included).
video cable with a male BNC connector through the
wall to where the camera is to be mounted.2
2. Temporarily connect the camera to the power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided. If needed, 7. Mount the camera base to the mounting plate using
use the included SECO-LARM DC plug with
the four included hex screws.
terminal block.
8. Adjust the camera angle.
3. Remove service cover and connect included service 9. Adjust zoom and focus. Then use the OSD control
monitor port connector to service monitor port.
4. Connect the service monitor port connector’s BNC to
a test monitor.
joystick to adjust camera settings. (See OSD
manual).
10. Disconnect the power supply and service
monitor connector.
5. While watching the monitor, hold the camera against
the wall or ceiling by hand where it is to be mounted, 11. Put the sunshield on the camera.
then turn the camera until it is certain that this
mounting location is correct. Use a pencil to mark
the location of the four screw holes in the mounting
plate.
12. Do a final test of the video camera and monitor.
2Note: The base also allows for surface running of the
wires. However, for a cleaner, more secure
installation, run the wires through the wall.
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
NVD Bullet Cameras
Troubleshooting
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
IR LEDs do not turn on.
IMPORTANT
Check that the correct power supply is in use.
Check that the correct power supply is in use.
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of three (3) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
PIKHR1
MiEV-1626NxGQ_1105.docx
Made in Korea
4
Download from Www.Somanuals.com. All Manuals SearSchEACndOD-oLwAnlRoaMd. U.S.A., Inc.
|