36 IR LED
Day/Night Bullet Camera
Manual
EV-1146-N6SQ
EV-1646-N6SQ
420 TV Lines
540 TV Lines
1/3” Sony Color CCD
6mm lens
53° viewing angle
Up to 100’ (30m) range
Weatherproof (IP66) construction
Concealed wiring for added security
Split glass design eliminates IR
reflection.
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM 36 IR LED Day/Night Bullet Cameras
Overview:
Adjustment screw
Adjustment ring
Adjustment screw
Sunshield
Adjustment screw
Female BNC
connector
Important:
Do not cut DC jack or female
BNC connector as warranty
will be voided.
IR LEDs
Mounting screw
Camera base
Important:
Do not remove label or open case as warranty will be voided.
DC jack
DC plug with
terminal block
Before Starting:
1. Please read this manual carefully and keep it for 6. Do not open or disassemble the camera. There
future reference.
2. Use the camera within given temperature and
electrical limits.
are no user-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
3. Do not aim the LED light directly at the eyes
when the LEDs are on.
Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-gaussing, which occurs automatically with many
monitors when the monitor is turned on.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.*
Installation:
1. Run a 12VDC power-supply wire and a video
cable with a male BNC connector through the wall
to where the camera will be mounted
5. Mount the camera by using the four included
mounting screws to secure the camera base to the
wall. If the wall is made of drywall, brick, or similar
material, it may be necessary to use the four
included screw anchors.
(if necessary).
2. Connect the camera to the 12VDC power supply.
Do not cut the DC jack or female BNC
connector as the warranty will be voided. If
needed, use the included
SECO-LARM DC plug with terminal block.
3. Connect the camera’s female BNC connector to
the video cable’s male BNC connector.
While watching the monitor, hold the camera
base against the wall where it is to be mounted,
then twist the camera until it is certain that this
mounting location is correct. Use a pencil to mark
the location screw holes in the base.
6. Turn the monitor on and make sure the camera is
sending the proper video signal.
7. The camera has 3-axis angle adjustment. Use the
included allen wrenches to loosen the adjustment
screws as needed. To adjust the horizontal axis,
the adjustment ring must also be loosened. After all
angle adjustments are made, re-tighten the
adjustment ring and the adjustment screws.
8. Re-tighten the adjustment knob and screws.
9. Do a final test of the video camera and monitor.
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM 36 IR LED Day/Night Bullet Cameras
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
IR LEDs do not turn on.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for
a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
E-mail: [email protected]
PICSN4
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
MiEV-1xx6-N6SQ_1007.docx
4
SECO-LARM U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|