OPERATOR’S MANUAL
BACKPACK BLOWER
RY08570
Your Backpack Blower has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
n
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
n
Never operate the unit without a spark arrestor screen;
this screen is located inside the muffler.
n
Product users on United States Forest Service land, and
in some states, must comply with fire prevention regu-
lations. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
the federal, state, or local authorities in your area.
n
Do not allow children or untrained individuals to use this
unit.
n
n
Never start or run the engine inside a closed area; breath-
ing exhaust fumes can kill.
n
n
Before storing, allow the engine to cool.
WeareyeprotectionwhichismarkedtocomplywithANSI
Z87.1 as well as hearing protection when operating this
equipment.
Use only Ryobi replacement parts and accessories. Fail-
ure to do so may cause poor performance or possible
injury.
n
n
n
n
Keep all bystanders, children, and pets at least 50 feet
(15 m) away.
Maintain the unit per maintenance instructions in this
operator’s manual.
Wear heavy long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, jewelry of any kind, or
go barefoot.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
SERVICE
n
To reduce the risk of injury associated with objects being
drawn into rotating parts, do not wear loose clothing,
scarves, neck chains, and the like. Secure long hair so it
is above shoulder level to prevent entanglement in any
rotating parts.
nBefore cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent starting.
nService on the blower must be performed by qualified
repair personnel only. Service or maintenance performed
by unqualified personnel could result in injury to the user
or damage to the product.
n
Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
n
n
Do not operate in poor lighting.
Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
nUse only identical replacement parts when servicing the
blower. Use of unauthorized parts may create a risk of
serious injury to the user, or damage to the product.
n
n
Wear a face filter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
Checktheworkareabeforeeachuse. Removeallobjects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
n
n
n
Select bare ground, stop engine, and allow to cool before
refueling.
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
n
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
To reduce the risk of injury associated with contacting
rotating parts, stop the engine before installing or
removing attachments. Do not operate without guard(s)
in place. Always disconnect the spark plug before
performing maintenance or accessing any movable
parts.
n
n
Tighten the fuel cap securely after refueling.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
n
Never attempt to burn off spilled fuel under any circum-
stances.
n
Do not point the blower nozzle in the direction of people
or pets.
nStore fuel in a cool, well-ventilated area, safely away from
n
n
n
Never run the unit without the blower tubes installed.
Never place objects inside the blower tubes.
spark and/or flame-producing equipment.
nStore fuel in containers specifically designed for this
Never use for spreading chemicals, fertilizers, toxic sub-
stances, or any other hazardous chemical.
purpose.
nOnly refuel outdoors and do not smoke while refueling.
n
Always hold the blower in your right hand. Refer to the
“Operation” later in this manual for additional infor-
mation.
nAdd fuel before starting the engine. Never remove the cap
of the fuel tank or add fuel while the engine is running or
when the engine is hot.
nIf fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
REFUELING
nFuel is highly flammable. Take precautions when using
to reduce the chance of serious personal injury.
n
n
Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
nReplace all fuel tank and container caps securely.
nWhen draining the fuel tank, use an approved fuel storage
To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
container while in a well-ventilated area.
n
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
n
n
n
Do not smoke while handling fuel.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or flames.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpre-
tation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
Safety Alert
DESIGNATION/EXPLANATION
Precautions that involve your safety.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Eye and Hearing Protection
Wear eye and hearing protection when operating this equipment.
Failure to keep long hair away from the air inlet could result in
personal injury.
Long Hair
Failure to keep loose clothing from being drawn into air intake
could result in personal injury.
Loose Clothing
Use unleaded gasoline intended for motor vehicle use with an
octane rating of 87 [(R + M)/2] or higher. This product is powered
by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle
oil.
Gasoline and Oil
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Weight .....................................................................................................................................................................11.75 lbs.
Engine displacement....................................................................................................................................................25.4cc
Air Velocity:
MPH...............................................................................................................................................................................180
CFM ...............................................................................................................................................................................375
HARNESS HEIGHT
ADJUSTMENTS
ENGINE
HARNESS
STRAPS
ELBOW
MESH
BACKING
ENGINE
SWITCH
STRAIGHT TUBE
(UPPER TUBE)
CABLE
TIE
WAIST
HARNESS
BELLOWS
NOZZLE
(LOWER TUBE)
THROTTLE
TRIGGER
THROTTLE HANDLE
THROTTLE CONTROL HANDLE TUBE
(UPPER TUBE)
Fig. 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR BLOWER
THROTTLE TRIGGER
See Figure 1.
The blower can be operated at any speed between idle and
full throttle.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
ADJUSTABLE HARNESS AND WAIST STRAPS
The blower comes with fully adjustable harness and waist
straps to ensure user comfort and ease of operation.
MOTOR
The blower has a powerful 25.4cc engine with sufficient
power to handle tough jobs.
MESH BACKING
The blower comes equipped with a mesh backing which
aids in user comfort.
CRUISE CONTROL / THROTTLE LOCK
The Cruise Control (throttle lock) feature allows the user to
operate the blower without holding the throttle trigger.
BLOWER TUBES
The blower tubes can be assembled and installed on the
blower without using tools.
ADJUSTABLE THROTTLE CONTROL HANDLE
Adjust the throttle control handle easily by loosening handle
knob, allowing user to position handle in desired location.
ASSEMBLY
UNPACKING
This product requires assembly.
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n Do not discard the packing material until you have care-
WARNING:
Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration
or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
PACKING LIST
Backpack Blower
WARNING:
Elbow
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
Bellows
Throttle Control Handle Tube (Upper Tube)
Straight Tube (Upper Tube)
Cable Tie (2)
Nozzle Tube (Lower Tube)
2-Cycle Engine Oil
Operator’s Manual
NOTE: Read and remove all hang tags and store with your
operator's manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
WARNING:
Disconnect the spark plug wire before assembling parts.
Failure to do so could result in possible serious personal
injury.
ASSEMBLING THE BLOWER TUBES
See Figures 2 - 4.
nAssemble the elbow tube onto blower by aligning raised
locking tabs on blower unit with the raised locking slots
on elbow as shown and twist to secure.
ELBOW
TUBE
nAttach bellows onto elbow tube by aligning raised lock-
ing tabs on elbow tube with the raised locking slots on
bellows and twist to secure.
BELLOWS
THROTTLE
CONTROL
HANDLE TUBE
(UPPER TUBE)
nAttach throttle control handle tube onto bellows by
aligning raised locking tabs on bellows with the raised
locking slots on throttle control handle tube and twist to
secure.
Fig. 2
NOTE: The position of the throttle control handle may be
adjusted for the best comfort after the blower is strapped
onto the operator’s back.
THROTTLE CONTROL
HANDLE TUBE
(UPPER TUBE)
nJoin the straight upper tube and nozzle together by align-
ing raised locking tabs on straight upper tube with the
raised locking slots on nozzle and twist to secure.
nAssemble the connected lower tubes to the throttle
control handle tube by aligning raised locking tabs on
the throttle control handle tube with the raised locking
slots on connected lower tubes by twisting to secure.
NOZZLE
NOTE: Check all locking connections after initial run to
ensure they are tightly secured.
UPPER TUBE
nHold the throttle cable against the bellows and install the
cable ties. Cable ties should be tight enough to retain
the throttle cable to the bellows but still allow for move-
ment.
Fig. 3
THROTTLE
CONTROL
HANDLE TUBE
(UPPER TUBE)
THROTTLE
CABLE
CABLE TIE
Fig. 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To adjust waist strap assembly:
nWaist strap should be tightened or loosened until adjusted
CAUTION:
to a comfortable operating position.
Make all adjustments to the harness straps before start-
ing the blower to avoid the possibility of injury.
ADJUSTING THROTTLE CONTROL HANDLE
See Figure 5.
ADJUSTING HARNESS AND WAIST STRAPS nLoosen throttle control handle locking screw by twisting
counterclockwise.
Straps should be adjusted to a comfortable position before
nMove throttle control handle to desired position and
starting the blower.
secure locking screw by twisting clockwise.
To adjust harness strap assembly:
nBlower should be in operating position before adjusting
the harness straps. Slip arm through harness strap and
onto shoulder, then repeat for the other shoulder.
nThere are three possible height adjustment positions that
can be used to easily adjust harness assembly.
nSlip top buckle of harness assembly from adjustment slot
and position to desired height location.
nTighten (pull down on strap) or loosen (lift up on tab of
strap buckle) each harness strap as needed, until each
are adjusted to a comfortable operating position.
nChest strap should be tightened or loosened until adjusted
Fig. 5
to a comfortable operating position.
OPERATION
MIXING THE FUEL
WARNING:
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle oil. The mixture should be
at a 50:1 ratio, using Premium Exact Mix™ 2-cycle engine
oil. If Premium Exact Mix™ 2-cycle engine oil is not avail-
able, use a high quality 2-cycle engine oil, mixed at a 50:1
ratio. See chart later in this section.
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
To mix the fuel:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
n Use a clean container that is approved for use with gaso-
line.
n Mix the Premium Exact Mix™ 2-cycle engine oil with
unleaded gasoline in the container, according to the
instructions on the oil package.
APPLICATIONS
You may use this tool for the purposes listed below:
NOTE: This engine is certified to operate on unleaded gaso-
line intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.
NOTE: Premium Exact Mix™ fuel mixture will stay fresh up
to 30 days. DO NOT mix quantities larger than usable in a
30 day period.
nClear leaves and other debris from your lawn
nKeep decks and driveways free from leaves and pine
needles
WARNING:
PREMIUM EXACT MIX™ (50:1)
Gasoline is extremely flammable and explosive. A fire or
explosion from gasoline will burn you and others.
GASOLINE
OIL
1 gallon (US)
1 Liter
2.6 oz.
20 cc (20 ml)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
nSet the choke lever to the START position.
FILLING THE TANK
WARNING:
Always stop the engine before filling the fuel tank. Never
add fuel to a machine with a running or hot engine. Move
atleast30ft.fromtherefuelingareabeforestartingengine.
Do not smoke while filling the tank.
NOTE: If restarting a warm engine, leave the choke lever
in the RUN position.
nPull the starter cord until the engine runs.
nReturn the starter cord gently to the starter housing. Do
not allow the rope to snap back.
nAllow the engine to run for 15 seconds to warm up before
using.
n Cleanthesurfacearoundthefuelcaptopreventcontami-
nEngage the throttle trigger to operate.
To stop the Backpack Blower:
n Release the throttle trigger.
nation.
n Loosen the fuel cap slowly, by turning it counter-
clockwise.
n Press and hold the engine switch to the “O” or STOP posi-
n Pour the fuel mixture carefully into the tank.
tion.
n Clean and inspect the fuel cap gasket before replacing
To Remove Backpack Blower:
the fuel cap.
nMove harness straps off the shoulders. Let straps slide
n Replace the fuel cap and tighten it by turning it clock-
down arms.
wise.
nGrasp the straps and lower the blower to the ground.
n Wipe spilled fuel from the product.
n Move at least 30 ft. away from refueling area before start-
ENGINE
SWITCH
ing the product.
WARNING:
Check for fuel leaks. If you find any leaks, correct the
problem before using the product.
WARNING:
CRUISE CONTROL
(THROTTLE LOCK)
A leaking fuel cap is a fire hazard and must be replaced
immediately.
THROTTLE
TRIGGER
Fig. 6
STARTING AND STOPPING
See Figures 6 - 7.
CHOKE
LEVER
CHOKE
LEVER
NOTE: It is normal for smoke to be emitted from a new
engine during first use.
START
POSITION
To start an engine that is cold or has run dry:
RUN
POSITION
nFill the fuel tank, if necessary. Always use the proper
oil/gasoline mixture. See “Mixing the Fuel” on page 10.
nDisengage the cruise control lever.
NOTE: Do not engage the throttle trigger during the
starting process.
nSlowly push the primer bulb seven times.
Fig. 7
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PROPER OPERATING POSITION
WARNING
Keep away from all hot surfaces of the blower. Failure to
do so could result in possible serious personal injury.
OPERATING THE BLOWER
See Figure 8.
nStart the blower. Refer to “Starting and Stopping” earlier
in this manual. Slip arm through harness strap and onto
shoulder, then repeat for the other shoulder. Adjust the
straps to a comfortable position. Refer to “Adjusting Har-
ness Straps” earlier in this manual. Operate the blower
from the right side as shown in illustration.
nTo keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
nTo reduce sound levels, limit the number of pieces of
equipment used at any one time.
nOperate blower at the lowest possible throttle speed to
do the job.
nCheck your equipment before operation, especially the
muffler, air intakes and air filters.
nUse rakes and brooms to loosen debris before blowing.
In dusty conditions, slightly dampen surfaces when water
is available.
nConserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas
such as gutters, screens, patios, grills, porches and
gardens.
Fig. 8
nWatch out for children, pets, open windows or freshly
washed cars, and blow debris safely away.
nUse the nozzle for larger volume, so the air stream can
work close to the ground.
nAfter using blowers or other equipment, CLEAN UP!
Dispose of debris properly.
CRUISE CONTROL
(THROTTLE LOCK)
CRUISE CONTROL / THROTTLE LOCK
The Cruise Control (throttle lock) can be used to operate the
blower without holding the throttle trigger.
To engage the cruise control / throttle lock:
See Figure 9.
n Pull cruise control lever back toward user, and stop at
THROTTLE TRIGGER
the desired throttle setting.
n To release the cruise control, push cruise control lever all
the way toward the front of unit.
Fig. 9
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING AND CLEANING AIR FILTER
See Figure 10.
WARNING:
A wet or dirty air filter can affect the way the engine starts,
performs, and wears. The air filter should be checked and
cleaned after 8 hours of operation. If working in dusty soil,
check the air filter after each refueling.
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
For best performance, the air filter should be replaced once
each year.
WARNING:
To clean the air filter:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
nLoosen the knob on the air filter cover.
nRemove the cover.
nLift the edge of the air filter carefully and peel it out.
nWash the air filter with warm, soapy water.
nRinse and squeeze to dry.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
nReinstall the air filter.
NOTE: Make sure the filter is seated properly inside the
cover. Installing the filter incorrectly will allow dirt to enter
the engine, causing rapid engine wear.
nReinstall the cover.
nTighten knob to secure.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
AIR FILTER
KNOB
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
AIR FILTER
COVER
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Ryobi Authorized Service Center.
Fig. 10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SPARK ARRESTOR
WARNING:
The muffler is equipped with a spark arrestor screen inside
muffler body. After extended use the screen can become
dirty and the screen may need to be replaced by an autho-
rized servicing dealer.
A leaking fuel cap is a fire hazard and must be replaced
immediately.
SPARK PLUG
This engine uses a Champion RCJ4 with 0.63 mm
(0.025 in.) electrode gap. Use an exact replacement and
replace annually.
WARNING:
To avoid a fire hazard, never run the blower without the
spark arrestor in place.
STORAGE (1 MONTH OR LONGER)
n Drain all fuel from the tank into a container approved for
CLEANING THE EXHAUST PORT AND MUFFLER
gasoline. Run engine until it stops.
Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port,
muffler, and/or spark arrestor screen may become blocked
with carbon deposits. If you notice a power loss with your
gas powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
n Clean all foreign material from the blower. Store it in a
well-ventilatedplacethat isinaccessibletochildren.Keep
away from corrosive agents such as garden chemicals
and de-icing salts.
n Abide by all Federal and local regulations for the safe
storage and handling of gasoline. Excess fuel should be
used up in other 2-cycle engine powered equipment.
FUEL CAP
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine per-
formance. If performance improves when the fuel cap is
loosened, the check valve may be faulty or filter clogged.
Replace the fuel cap if required.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
The following recommended accessories are currently
available.
WARNING:
ACCESSORIES
Current attachments and accessories available
for use with this tool are listed. Do not use any
attachments or accessories not recommended by the
manufacturer of this tool. The use of attachments or
accessories not recommended can result in serious
personal injury.
Air Filter .........................................Power Care - AP04107
Spark Plug......................................... Champion - RCJ-6Y
Fuel Cap.............................................................. AP04108
2-Cycle Oil.......................... (2.6 FL. OZ - 76 ml) AR99G01
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORIZED SERVICING DEALER.
PROBLEM
Engine fails to start.
CAUSE
REMEDY
No fuel in tank.
Fill tank.
Spark plug shorted or fouled.
Replace spark plug.
Replace spark plug.
Spark plug is broken (cracked
porcelain or electrodes broken).
Ignition lead wire shorted, broken, or Replace lead wire or attach to spark
disconnected from spark plug.
plug.
Ignition inoperative.
Contact authorized service center.
Engine hard to start.
Water in gasoline or stale fuel mixture. Drain entire system and refill with fresh
fuel.
Too much oil in fuel mixture.
Engine is under or over choked.
Weak spark at spark plug.
Air filter clogged.
Drain and refill with correct mixture.
Adjust choke as necessary.
Contact authorized service center.
Clean or replace air filter.
Engine lacks power.
Engine overheats.
Insufficient oil in fuel mixture.
Mix fuel as described in starting
instructions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTY STATEMENT
In addition, this warranty does not cover:
Ryobi Technologies, Inc. warrants to the original retail
purchaser that this Ryobi Technologies, Inc. product is
free from defect in material and workmanship and agrees
torepairorreplace,atRyobiTechnologies,Inc.’sdiscretion,
any defective product free of charge within these time
periods from the date of purchase.
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting
Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts,Tines,FeltWashers,HitchPins,MulchingBlades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bag
and Straps, Guide Bars, Saw Chains
n Two years if the product is used for personal, family or
household use;
Ryobi Technologies, Inc. reserves the right to change or
improvethedesignofanyRyobiTechnologies,Inc.product
without assuming any obligation to modify any product
previously manufactured.
n 90 days, if used for any other purpose, such as
commercial or rental.
This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY
DAY WARRANTY PERIOD. RYOBI TECHNOLOGIES,
INC.’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR
OR REPLACEMENT OF DEFECTIVE PARTS AND
RYOBI TECHNOLOGIES, INC.DOES NOT ASSUME OR
AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. RYOBI TECHNOLOGIES, INC. ASSUMES NO
RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,
OROTHERDAMAGESINCLUDING,BUTNOTLIMITEDTO,
EXPENSEOFRETURNINGTHERYOBITECHNOLOGIES,
INC. PRODUCT TO AN AUTHORIZED SERVICE DEALER
ANDEXPENSEOFDELIVERINGITBACKTOTHEOWNER,
MECHANIC’STRAVELTIME,TELEPHONEORTELEGRAM
CHARGES, RENTAL OF A LIKE PRODUCT DURING THE
TIME WARRANTY SERVICE IS BEING PERFORMED,
TRAVEL, LOSS OR DAMAGE TO PERSONAL PROPERLY,
LOSS OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
Any part of the Ryobi Technologies, Inc. product
manufactured or supplied by Ryobi Technologies, Inc. and
found in the reasonable judgment of Ryobi Technologies,
Inc. to be defective in material or workmanship will be
repaired or replaced by an authorized Ryobi Technologies,
Inc. service dealer without charge for parts and labor.
Theproduct,includinganydefectivepart,mustbereturned
to an authorized service dealer within the warranty period.
The expense of delivering the Ryobi Technologies, Inc.
product to the dealer for warranty work and the expense
ofreturningitbacktotheownerafterrepairorreplacement
will be paid by the owner. Ryobi Technologies, Inc.’s
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach
of warranty shall be cause for cancellation or rescission
of the contract of sale of any Ryobi Technologies, Inc.
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by an authorized Ryobi Technologies, Inc.
service dealer.
This warranty is limited to ninety (90) days from the date
of original retail purchase for any Ryobi Technologies, Inc.
product that is used for rental or commercial purposes, or
any other income-producing purpose.
This warranty does not cover any Ryobi Technologies,
Inc. product that has been subject to misuse, neglect,
negligence, or accident, or that has been operated in any
way contrary to the operating instructions as specified
in this operator’s manual. This warranty does not apply
to any damage to the Ryobi Technologies, Inc. product
that is the result of improper maintenance or to any
Ryobi Technologies, Inc. product that has been altered
or modified. The warranty does not extend to repairs
made necessary by normal wear or by the use of parts or
accessories which are either INCOMPATIBLE WITH THE
RYOBITECHNOLOGIES,INC.productoradverselyaffect
its operation, performance, or durability.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all Ryobi Technologies, Inc.
products manufactured by Ryobi Technologies, Inc. and
sold in the United States and Canada.
To locate your nearest service dealer, dial 1-800-860-4050.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.
RYOBI TECHNOLOGIES, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION
CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Ryobi Technologies, Inc. are pleased
to explain the Emission Control System Warranty on your non-road or small off-road engine. In California, new small off-road engines
must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model
year non-road engines must be designed, built, and equipped, at the time of sale, to meet the U.S. EPA regulations for small non-road
engines. The non-road engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA
standards for the first two years of engine use from the date of sale to the ultimate purchaser. Ryobi Technologies, Inc. must warrant
the emission control system on your non-road or small off-road engine for the period of time listed above provided there has been no
abuse, neglect, or improper maintenance of your non-road or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic
converter. Also included may be hoses, belts and connectors, and other emission related assemblies.
Where a warrantable condition exists, Ryobi Technologies, Inc. will repair your non-road or small off-road engine at no cost to you,
including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:
The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year non-
road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or
replaced by Ryobi Technologies, Inc. free of charge.
OWNER’S WARRANTY RESPONSIBILITIES
(a) As the non-road or small off-road engine owner, you are responsible for the performance of required maintenance listed in your
operator’s manual. Ryobi Technologies, Inc. recommends that you retain all receipts covering maintenance on your non-road or
small off-road engine, but Ryobi Technologies, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability
may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
(b) As the non-road or small off-road engine owner, you should be aware, however, that Ryobi Technologies, Inc., may deny you
warranty coverage if your non-road or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or
unapproved modifications.
(c) You are responsible for presenting your non-road or small off-road engine to a Ryobi Technologies, Inc., service dealer as soon as
a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a Ryobi Technologies, Inc., Customer
Representative at 1-800-860-4050.
COVERAGE:
Ryobi Technologies, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your non-road or small off-road
engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Ryobi Technologies, Inc. also war-
rants to the initial purchaser and each subsequent purchaser that your non-road or small off-road engine is free from defects in mate-
rials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and
later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires
manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the non-road or small off-
road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by
Ryobi Technologies, Inc. at no cost to the owner.
Ryobi Technologies, Inc. shall remedy warranty defects at any authorized Ryobi Technologies, Inc. engine dealer or warranty sta-
tion. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work deter-
mines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty
maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty.
Ryobi Technologies, Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s
regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)
These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.
MAINTENANCE REQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by Ryobi Technologies, Inc. in the operator’s
manual.
LIMITATIONS
The Emission Control Systems Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or
replacements not conforming to Ryobi Technologies, Inc. specifications that adversely affect performance and/or durability, and
alterations or modifications not recommended or approved in writing by Ryobi Technologies, Inc., and
(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled
replacement point.
The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which
the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts
Inspect Before
Each Use
Clean Every
5 Hours
Replace
Every 25 Hours
or Yearly
Clean Every
25 Hours
or Yearly
Replace Every
50 Hours
CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X
AIR FILTER ASSY
includes:
Filter ................................................................. X............................. X
SPARK SCREEN ..................................................................................................................X
CARBURETOR ASSY
includes:
Heat Dam
Gaskets
FUEL TANK ASSY
includes:
Fuel Lines........................ X
Fuel Cap.......................... X
Fuel Filter
IGNITION ASSY
includes:
Spark Plug........................................................................................ X
ALL EMISSIONS RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
CALL US FIRST
For any questions about operating or maintaining your product,
call the Ryobi® Help Line!
Your product has been fully tested prior to shipment to ensure
your complete satisfaction.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
BACKPACK BLOWER
RY08570
WARNING:
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
CALIFORNIA PROPOSITION 65
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
RY08570
• MODEL NUMBER
• SERIAL NUMBER
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-860-4050
983000-699
3-05
Download from Www.Somanuals.com. All Manuals Search And Download.
|