OPERATOR’S MANUAL
18 in. ELECTRIC CHAIN SAW
DOUBLE INSULATED
RY43006
Your chain saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
short pants, sandals, or go barefoot. Do not wear loose
fitting clothing, which could be drawn into the motor or
catch the chain or underbrush. Secure hair so it is above
shoulder level.
WARNING:
Do not attempt to operate this unit until you have read
thoroughly and understand completely all instructions,
safety information, etc. contained in this manual. Failure
to comply can result in accidents involving fire, electric
shock, or serious personal injury.
n WeareyeprotectionwhichismarkedtocomplywithANSI
Z87.1 as well as hearing and head protection when oper-
ating this equipment.
n Always be aware of what you are doing when using the
chain saw. Use common sense. Do not operate the chain
saw when you are tired, ill, or under the influence of al-
cohol, drugs, or medication.
READ ALL INSTRUCTIONS
BASIC SAFETY PRECAUTIONS
nDo not start cutting until you have a clear work area, se-
cure footing, and a planned retreat path from the falling
tree. Cluttered areas invite accidents.
n Do not expose the chain saw to rain.
n Do not use the chain saw in damp or wet locations.
n Always be aware of extension cord while operating chain
saw. Take precautions to avoid tripping over cord. Keep
cordawayfromchainandoperatoratalltimes.Nevercarry
saw by the cord or pull it to disconnect from receptacle.
Keep cord from oil and sharp edges.
n Keep ALL children, bystanders, visitors, and animals out
of the work area while starting or cutting with the chain
saw.
nDo not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the dust
or fumes.
n Stay alert and pay attention to what you are doing. Use
common sense when using this unit.
n Keep all parts of your body away from the saw chain
n
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords are rated
for outdoor use and reduce the risk of electric shock.
when the unit is running.
n Always carry the chain saw by the front handle with the
unitunpluggedandtheguidebarandsawchainpositioned
to the rear. When transporting your chain saw, use the
appropriate guide bar scabbard.
n Neverletanyoneuseyourchainsawwhohasnotreceived
adequate instructions in its proper use. This applies to
rentals as well as privately owned saws.
n Before you start the unit, make sure the saw chain is not
contacting any object.
n Stop the chain saw before setting it down.
nPolarized Plugs. To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any
way.
nMake sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. A wire gauge
size (A.W.G.) of at least 12 is recommended for an exten-
sion cord 50 feet or less in length. A cord exceeding 100
feet is not recommended. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the
cord. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
n Toavoidaccidentalstarting, nevercarrytheunitwithyour
finger on the switch trigger.
n Maintain the unit with care. Keep the cutting edge sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and changing
accessories.
n Keep handles dry, clean, and free of oil and grease.
nInspect extension cords periodically and, if damaged,
have repaired by a licensed electrician. Constantly stay
aware of cord location. Following this rule will reduce the
risk of electric shock or fire.
n Do not operate a chain saw with one hand! Use a firm grip
with thumbs and fingers encircling the chain saw handles.
Serious injury to the operator, helpers, bystanders, or any
combinationofthesepersonsmayresultfromone-handed
operation. A chain saw is intended for two-handed use.
n Wearsnugfittingclothing.Alwayswearheavy,longpants,
overalls, jeans or chaps made of cut resistant material or
onesthatcontaincutresistantinserts.Wearnon-slipsafety
footwear. Wear non-slip heavy duty gloves to improve
your grip and to protect your hands. Do not wear jewelry,
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
nAvoid body contact with grounded surfaces such as metal n Do not cut vines and/or small underbrush.
pipes and wire fences. There is an increased risk of electric
shock if your body is grounded.
n Do not operate a chain saw in a tree, on a ladder, or scaf-
fold; this is extremely dangerous.
n Do not operate a chain saw that is damaged, improperly
NOTE: The size of the work area depends on the job
adjusted, or not completely and securely assembled.
being performed as well as the size tree or work piece
Chain should slow to a stop when the switch trigger is
involved. For example, felling a tree requires a larger work
released. If the chain continues to turn after the switch
area than making bucking cuts.
trigger has been released, have the unit serviced by your
n Use extreme caution when cutting small size brush and
nearest Ryobi service dealer.
saplings,becausesmallmaterialmaycatchthesawchain
and be whipped toward you or pull you off balance.
n Check for damaged parts. Check for alignment of mov-
ing parts, binding of moving parts, breakage of parts,
n When cutting a limb that is under tension, be alert for
mounting, and any other conditions that may affect its
spring back so that you will not be struck when the ten-
operation. A guard or other part that is damaged should
sion in the wood fibers is released.
be properly repaired or replaced by an authorized ser-
vice dealer unless otherwise indicated elsewhere in this
manual.
n Do not force the chain saw. The job can be performed
better and safer at the rate for which it was intended.
n Always use the right product for your application. The
chain saw should be used for cutting wood only. Never
use the chain saw to cut plastic, masonry or non-wood
building materials.
n All chain saw service, other than the items listed in the
operationandmaintenancesections,shouldbeperformed
by your nearest Ryobi service dealer.
n Always maintain a proper stance.
n Do not use the chain saw for purposes not intended.
n Do not use chain saw if switch does not turn it on and off.
Have defective switches replaced by authorized service
center.
n Store chain saw when not in use. Chain saw should be
stored in a dry and high or locked area out of the reach
of children. When storing chain saw place the scabbard
on the bar and chain and store the chain saw in carrying
case.
n Do not adapt your powerhead to a bow guide or use it
to power any attachments or devices not listed for the
saw.
nSave these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
n Disconnect chain saw when not in use, before servicing,
andwhenmakingadjustmentsandchangingattachments,
such as saw chain and guard.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
KICKBACK
See Figures 1 - 2.
ROTATIONAL
KICKBACK
WARNING:
Kickback may occur when the moving chain contacts an
object at the upper portion of the tip of the guide bar or
whenthewoodclosesinandpinchesthesawchaininthe
cut. Contact at the upper portion of the tip of the guide
barcancausethechaintodigintotheobjectandstopthe
chain for an instant. The result is a lightning fast, reverse
reaction which kicks the guide bar up and back toward
the operator. If the saw chain is pinched along the top of
the guide bar, the guide bar can be driven rapidly back
toward the operator. Either of these reactions can cause
loss of saw control which can result in serious injury. Do
not rely exclusively upon the safety devices built into the
saw. As a chain saw user, you should take several steps
to keep your cutting jobs free from accident or injury.
BAR SHOWN WITHOUT SAFE-T-TIP® NOSE GUARD FOR
ILLUSTRATION PURPOSES ONLY
Fig. 1
KICKBACK
DANGER ZONE
n The following precautions should be followed to mini-
mize kickback:
1. Always grip the saw firmly with both hands. Hold the
saw firmly with both hands when the unit is running.
Place your right hand on the rear handle and your left
hand on the front handle with your thumbs and fingers
encircling the chain saw handles. A firm grip together
with a stiff left arm will help you maintain control of
the saw if kickback occurs.
Fig. 2
2. Make sure that the area in which you are cutting is free
from obstructions. Do not let the nose of the guide bar
contact a log, branch, fence, or any other obstruction
that could be hit while you are operating the saw.
3. Alwayscutwiththeunitrunning.Fullysqueezetheswitch
trigger and maintain cutting speed.
4. Use replacement parts such as low kickback chain
(partno.301304001),SAFE-T-TIP® anti-kickbacknose
guards and special guide bars that reduce the risks
associated with rotational kickback.
Use only the replacement guide bars (part no.
301139003) and low kickback chains specified by
the manufacturer for the saw.
PULL
n With a basic understanding of kickback, you can reduce
or eliminate the element of surprise. Sudden surprise
contributes to accidents.
n Keep proper footing and balance at all times.
n Do not cut above shoulder height or overreach when cutting.
n Keep the SAFE-T-TIP® anti-kickback nose guard properly
mounted on the guide bar to prevent rotational kickback.
n Follow the sharpening and maintenance instructions for
the saw chain.
n Push and Pull - This reaction force is always opposite to
the direction the chain is moving where wood contact is
made. Thus, the operator must be ready to control the
PULL when cutting on the bottom edge of the bar, and
PUSH when cutting along the top edge. See Figure 3.
PUSH
Fig. 3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
As saw chains are sharpened during their useful life, they
lose some of the low kickback qualities and extra caution
should be used.
UNDERSTANDING YOUR CHAIN SAW SAFETY
DEVICES
See Figure 4.
®
GUIDE BARS
Generally, guide bars with small radius tips have somewhat
lower kickback potentials.
SAFE-T-TIP ANTI-KICKBACK NOSE GUARD
The SAFE-T-TIP® prevents rotational kickback from hap-
pening, because it covers the tip of the bar where kickback
is generated. Never attempt any kind of cutting where the
SAFE-T-TIP® would have to be removed from the bar tip.
When making a replacement, be sure to order one of the
Ryobi bars listed for the saw in this operator's manual. The
proper size SAFE-T-TIP® nose guard comes installed on the
bar. Use only guide bars that have a provision for mounting
the SAFE-T-TIP®.
LOW KICKBACK SAW CHAIN
The rakers (depth gauges) ahead of each cutter can minimize
the force of a kickback reaction by preventing the cutters
from digging in too deeply at the kickback zone. Only use
replacement chain that is equivalent to original chain or has
been certified as low kickback chain per ANSI B175.1.
SAFE-T-TIP®
Low kickback/skip tooth saw chain is a chain that has met
the kickback performance requirements of ANSI B175.1
- 1991 (American National Standard for Power Tools - Gas-
oline-Powered Chain Saws-Safety Requirements) when
tested on the representative sample of chain saws below
3.8 c.i.d. specified in ANSI B175.1 - 1991.
Fig. 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
EXPLANATION
V
A
Volts
Voltage
Current
Amperes
Hertz
Hz
W
Frequency (cycles per second)
Power
Watt
min
Minutes
Time
Alternating Current
Direct Current
Type or a characteristic of current
Type or a characteristic of current
n0
No Load Speed
Rotational speed, at no load
Class II Construction
Designates Double Insulated Construction tools
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes, surface speed, orbits etc.
per minute
Safety Alert Symbol
Indicates danger, warning or caution. It means
attention!!! Your safety is involved.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
Read Your Operator’s Manual
Your manual contains special messages to bring
attention to potential safety concerns, machine
damage as well as helpful operating and servicing
information. Please read all the information care-
fully to avoid injury and machine damage.
Wear Eye, Hearing, and Head Protection
Wear eye protection which is marked to comply
with ANSI Z87.1 as well as hearing and head pro-
tection when operating this equipment.
Wear Safety Footwear
Wear Gloves
Wear non-slip safety footwear when using this
equipment.
Wearnon-slip,heavy-dutyprotectivegloveswhen
handling the chain saw.
Keep Children and Pets Away
Beware of Kickback
Danger- Keep children and pets away.
DANGER! Beware of kickback.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles,
safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is desig-
nated with “WA” on the cord’s jacket.
The double insulated system is intended to protect
the user from shock resulting from a break in the tool’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performedonlybyaqualifiedservicetechnician. Forservice,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
**Ampere rating (on tool data plate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25’
50’
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100’
ELECTRICAL CONNECTION
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC).
WARNING:
A substantial voltage drop will cause a loss of power and
the motor will overheat. If your tool does not operate when
plugged into an outlet, double-check the power supply.
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Bar Tip Guard
Kickback, Rotational
An attachment that may be provided on the end of the
guide bar to prevent the chain at the end of the guide bar
from contacting the wood.
The rapid upward and backward motion of the saw which
can occur when the moving saw chain near the upper
portion of the tip of the guide bar contacts an object, such
as a log or branch.
Bucking
The process of cross cutting a felled tree or log into
Low-Kickback Chain
lengths.
A chain that complies with the kickback performance
requirements of ANSI B175.1-1991 when tested on a
representative sample of chain saws.
Chain Brake
A device used to stop the chain saw.
Normal Cutting Position
Those positions assumed in performing the bucking and
felling cuts.
Chain Saw Powerhead
A chain saw without the saw chain and guide bar.
Clutch
Notching Undercut
A notch cut in a tree that directs the tree’s fall.
A mechanism for connecting and disconnecting a driven
member to and from a rotating source of power.
Oiler Control
A system for oiling the guide bar and saw chain.
Drive Sprocket or Sprocket
The toothed part that drives the saw chain.
Rear Handle
Felling
The support handle located at or toward the rear of the
saw.
The process of cutting down a tree.
Felling Back Cut
The final cut in a tree felling operation made on the opposite
side of the tree from the notching undercut.
Reduced Kickback Guide Bar
A guide bar which has been demonstrated to reduce
kickback significantly.
Front Handle
Replacement Saw Chain
The support handle located at or toward the front of the
chain saw.
A chain that complies with the kickback performance
requirements of ANSI B175.1-1991 when tested with
specific chain saws. It may not meet the ANSI performance
requirements when used with other saws.
Front Handle Guard
A structural barrier between the front handle of a chain
saw and the guide bar, typically located close to the hand
position on the front handle and sometimes employed as
an activating lever for a chain brake.
Saw Chain
A loop of chain having cutting teeth, that cut the wood, and
that is driven by the motor and is supported by the guide
bar.
Guide Bar
A solid railed structure that supports and guides the saw
chain.
Spiked Bumper (Spike)
The pointed tooth or teeth for use when felling or bucking
to pivot the saw and maintain position while sawing.
Kickback
The backward or upward motion, or both of the guide bar
occurring when the saw chain near the nose of the top
area of the guide bar contacts any object such as a log or
branch, or when the wood closes in and pinches the saw
chain in the cut.
Switch
A device that when operated will complete or interrupt an
electrical power circuit to the motor of the chain saw.
Switch Linkage
The mechanism that transmits motion from a trigger to the
switch.
Kickback, Pinch
The rapid pushback of the saw which can occur when the
wood closes in and pinches the moving saw chain in the
cut along the top of the guide bar.
Switch Lockout
A movable stop that prevents the unintentional operation of
the switch until manually actuated.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Bar Length................................................................. 18 in.
Chain Type ................................Skip Tooth/Low Kickback
Motor.......................................................................3.5 hp.
Bar and Chain Oil Capacity..................................... 7.1 oz.
No Load Speed (Sprocket).................................6200/min.
Input .............................120 V, 60 Hz, AC only, 13.0 Amps
Net Weight............................................................ 10.7 lbs.
FRONT GUARD
FRONT HANDLE
OIL RESERVOIR
CAP
SAFE-T-TIP®
REAR
HANDLE
LOW KICKBACK/
SKIP TOOTH
CHAIN
BAR
GUIDE BAR
NUT
CHAIN
TENSIONING
KNOB
SWITCH
LOCK
SWITCH
TRIGGER
RECEPTACLE
QUICK VIEW OIL
INDICATOR
EXTENSION CORD
HITCH
Fig. 5
KNOW YOUR CHAIN SAW
SWITCH LOCK
See Figure 5.
A control feature designed to prevent the motor from being
accidently started.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
SWITCH TRIGGER
Squeeze the switch trigger to operate the unit after switch
lock has been pushed in. Release the switch trigger to stop
the unit.
SAFE-T-TIP®
An attachment provided on the end of the guide bar
to prevent the chain, on the end of the guide bar, from
contacting the wood.
CHAIN TENSIONING KNOB
This feature allows user to adjust the tension of the chain.
REAR HANDLE
The support handle located at or toward the rear of the
chain saw.
QUICK VIEW OIL INDICATOR
Semi-transparent oil reservoir that allows user to see when
to add oil.
FRONT HANDLE
The support handle located at or toward the front of the
chain saw.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n Do not discard the packing material until you have care-
WARNING:
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
1-800-860-4050 for assistance.
PACKING LIST
Chain Saw with Scabbard
Scrench (combination wrench)
Case
WARNING:
Operator’s Manual
Warranty Registration Card
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
OPERATION
WARNING:
WARNING:
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
WARNING:
APPLICATIONS
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
You may use this tool for the purposes listed below:
nLimbing and pruning branches from trees.
nFelling trees up to 14 in. diameter.
nBucking the fallen tree into shorter lengths.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AUTOMATIC CHAIN OIL SYSTEM
OIL RESERVOIR
CAP
See Figure 6.
NOTE: Chain saw comes from the factory with no bar
and chain oil added.
n Use Power Care Bar and Chain Oil. It is formulated to
perform over a wide temperature range with no dilution
required.
n Remove oil cap.
n Carefully pour the bar and chain oil into the tank.
n Wipe off excess oil.
n Check and fill the oil tank when quick view oil indicator
is below the second to last indicator line.
n Repeat as needed.
QUICK VIEW
OIL INDICATOR
NOTE: Do not use dirty, used or otherwise contaminated
Fig. 6
oils. Damage may occur to the bar or chain.
NOTE: It is normal for oil to seep from the saw when not in
use. To prevent seepage, empty the oil tank after each use
then run for one minute. When storing the unit for a long
period of time (three months or longer) be sure the chain
is lightly lubricated; this will prevent rust on the chain and
bar sprocket.
EXTENSION
CORD
CONNECTING TO POWER SUPPLY
See Figure 7.
This chain saw is designed with an extension cord hitch
that prevents the extension cord from being pulled loose
while using.
n Form a loop with the end of the extension cord.
n Insert loop portion of extension cord through the opening
in the side of the rear handle and place over cord hitch.
EXTENSION
CORD HITCH
n Slowly pull loop against cord hitch until the slack is re-
moved.
Fig. 7
n Plug extension cord into rear handle of chain saw.
NOTE: Failure to remove all excess cord slack from
extension cord hitch could result in plug loosening from
receptacle.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING AND STOPPING THE CHAIN SAW
See Figure 8.
WARNING:
Keep body to the left of the chain line. Never straddle
the saw or chain, or lean over past the chain line.
STARTING THE CHAIN SAW
n Make sure no objects or obstructions are in immediate
vicinity which could come in contact with the bar and
chain.
n Press and hold the switch lock. This makes the switch
SWITCH LOCK
trigger operational.
n Press and hold the switch trigger, release the switch lock
and continue to squeeze the switch trigger for continued
operation.
SWITCH TRIGGER
STOPPING THE CHAIN SAW
NOTE: It is normal for the chain to coast to a stop once
the trigger switch is released.
SWITCH LOCK
n Release the switch trigger to stop the chain saw.
n Upon release of the switch trigger, the switch lock will be
automatically reset to the lock position.
Do not attempt to make any cut that would require removal
of the SAFE-T-TIP®.
SWITCH TRIGGER
Fig. 8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PREPARATION FOR CUTTING
PROPER GRIP ON HANDLES
FRONT
HANDLE
See Figures 9 - 11.
Refer to “General Safety Rules” earlier in this manual for
appropriate safety equipment.
n Wear non-slip gloves for maximum grip and protection.
n Hold the saw firmly with both hands. Always keep your
left hand on the front handle and your right hand on the
rear handle so that your body is to the left of the chain
line.
WARNING:
Never use a left-handed (cross-handed) grip, or any
stance which would place your body or arm across the
chain line.
REAR
HANDLE
Fig. 9
n Maintain a proper grip on the saw whenever the unit is
running. The fingers should encircle the handle and the
thumb is wrapped under the handlebar. This grip is least
likelytobebroken(byakickbackorothersuddenreaction
of the saw). Any grip in which the thumb and fingers are
on the same side of the handle, is dangerous because a
slight kick of the saw can cause loss of control.
WARNING:
Do not operate the switch trigger with your left hand
and hold the front handle with your right hand. Never
allow any part of your body to be in the chain line while
operating a saw.
Fig. 10
CHAIN LINE
Fig. 11
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PROPER CUTTING STANCE
See Figure 12.
n Weight should be balanced with both feet on solid
CHAIN LINE
ground.
n Keep left arm with elbow locked in a "straight arm" posi-
STRAIGHT ARM
POSITION
tion to withstand any kickback force.
n Your body should always be to the left of the chain line.
n Thumb should be on underside of handlebar.
BASIC CUTTING PROCEDURE
Practice cutting a few small logs using the following tech-
nique to get the "feel" of using the saw before you begin a
major sawing operation.
Fig. 12
n Take the proper stance in front of the wood with the saw
off.
n Always cut with both feet on solid ground to prevent be-
n Press the switch lock and squeeze the switch trigger
then release switch lock and let the chain accelerate to
full speed before entering the cut.
ing pulled off balance.
n Do not cut above chest height, as a saw held higher is
difficult to control against kickback forces.
n Begin cutting with the saw against the log.
n Do not fell trees near electrical wires or buildings. Leave
n Keep the unit running the entire time you are cutting,
this operation for professionals.
maintain a steady speed.
n Cut only when visibility and light are adequate for you to
n Allow the chain to cut for you; exert only light downward
pressure. If you force the cut, damage to the bar, chain,
or unit can result.
see clearly.
TREE FELLING
Unusual Hazardous Tree Felling Conditions
n Releasetheswitchtriggerassoonasthecutiscompleted,
allowing the chain to stop. If you run the saw without a
cutting load, unnecessary wear can occur to the chain,
bar, and unit.
Do not fell trees during periods of high wind or heavy pre-
cipitation.
n Do not put pressure on the saw at the end of the cut.
WARNING:
WORK AREA PRECAUTIONS
n Cut only wood or materials made from wood, no sheet
metal, no plastics, no masonry, no non-wood building
materials.
Do not cut down trees having an extreme lean or large
trees that have rotten limbs, loose bark, or hollow trunks.
Have these trees pushed or dragged down with heavy
equipment, then cut them up.
n Never allow children to operate the saw. Allow no person
to use this chain saw who has not read this Operator's
Manual or received adequate instructions for the safe
and proper use of this chain saw.
WARNING:
Do not cut trees near electrical wires or buildings.
n When felling a tree, keep everyone - helpers, bystanders,
children, and animals - a safe distance from the cutting
area. During felling operations, the safe distance should
be a least twice the height of the largest trees in the fell-
ing area. During bucking operations, keep a minimum
distance of 15 feet between workers. Trees should not
be felled in a manner that would endanger any person,
strike any utility line or cause any property damage. If
the tree does make contact with any utility line, the utility
company should be notified immediately.
WARNING:
Check the tree for damaged or dead branches that could
fall and hit you during felling.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PLANNED LINE OF FALL
WARNING:
Periodically glance at the top of the tree during the
backcut to assure the tree is going to fall in the desired
direction.
WARNING:
If the tree starts to fall in the wrong direction, or if the
saw gets caught or hung up during the fall, leave the saw
and save yourself!
n Felling a tree - When bucking and felling operations are
being performed by two or more persons, at the same
time, the felling operation should be separated from the
bucking operation by a distance of at least twice the
height of the tree being felled. Trees should not be felled
in a manner that would endanger any person, strike any
utility line or cause any property damage. If the tree does
make contact with any utility line, the utility company
should be notified immediately.
90°
SAFE
RETREAT
ZONE
PLANNED PATH OF SAFE RETREAT 135° FROM PLANNED LINE
OF FALL
n Before any cuts are started, pick your escape route (or
routes in case the intended route is blocked); clear the
immediate area around the tree and make sure there are
noobstructionsinyourplannedpathofretreat.Clearpath
of safe retreat approximately 135° from planned line of
fall. The retreat path should extend back and diagonally
to the rear of the expected line of fall. See Figure 13.
SAFE
RETREAT
ZONE
135°
PLANNED
LINE OF FALL
45°
45°
90°
n Before felling is started, consider the force and direction
of the wind, the lean and balance of the tree, and the lo-
cation of large limbs. These things influence the direction
in which the tree will fall. Do not try to fell a tree along a
line different from its natural line of fall.
135°
SAFE
RETREAT
ZONE
n The chain saw operator should keep on the uphill side
of the terrain as the tree is likely to roll or slide downhill
after it is felled.
Fig. 13
DIRECTION OF
FALL
n Remove dirt, stones, loose bark, nails, staples, and wire
from the tree where felling cuts are to be made.
n Notched Undercut. Cut a notch about 1/3 the diameter
of the tree, perpendicular to the direction of fall. Make the
cuts of the notch so they intersect at a right angle to the
line of fall. This notch should be cleaned out to leave a
straight line. To keep the weight of the wood off the saw,
always make the lower cut of the notch before the upper
cut. See Figure 14.
HINGE
2 IN. (5 CM) OR 1/10 DIA
NOTCH -
APPROX. 1/3
DIAMETER OF
TRUNK
BACK CUT
2 IN. (5 CM)
Fig. 14
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
n Felling Backcut. The backcut is always made level and
n
Sometimes it is impossible to avoid pinching (with just
standard cutting techniques) or difficult to predict which
way a log will settle when cut. To avoid pinching while
cutting, rotate or move the log so that the pinch is elimi-
nated.
horizontal, and at a minimum of 2 in. above the horizontal
cut of the notch. See Figures 14 - 15.
n Never cut through to the notch. Always leave a band of
woodbetweenthenotchandbackcut(approximately2in.
or 1/10 the diameter of the tree). This is called "hinge" or
“hingewood.” It controls the fall of the tree and prevents
slippingortwistingorshoot-backofthetreeoffthestump.
See Figures 14 - 15.
n On large diameter trees, stop the back cut before it is
deep enough for the tree to either fall or settle back on
the stump. Then insert soft wooden or plastic wedges
into the cut so they do not touch the chain. The wedges
can be driven in, little by little, to help jack the tree over.
See Figure 16.
NOTCH
BACK CUT
NOTE: When bucking or felling with a wedge, it may
be necessary to remove the SAFE-T-TIP® anti-kickback
device to allow the bar to be drawn through the cut.
After the cut is complete, the tip should be reinstalled
immediately.
HINGE
Fig. 15
n As tree starts to fall, stop the chain saw by releasing the
switch trigger and put it down immediately. Retreat along
the cleared path, but watch the action in case something
falls your way. Be alert for overhead limbs or branches
that may fall and watch your footing.
WARNING:
Never cut through to the notch when making a backcut.
The hinge controls the fall of the tree, this is the section
of wood between the notch and backcut.
WEDGE
KICKBACK
Fig. 16
BUCKING
See Figures 17 - 20.
Bucking is the term used for cutting a fallen tree to the de-
sired log length.
nAlways make sure your footing is secure and your weight
is distributed evenly on both feet.
nCut only one log at a time.
nSupport small logs on a saw horse or another log while
bucking.
Fig. 17
nKeep a clear cutting area. Make sure that no objects can
contact the guide bar nose and chain during cutting, this
can cause kickback. To avoid the danger, keep the SAFE-
T-TIP® anti-kickback device attached while cutting. Refer
to “Kickback” earlier in this manual.
nWhen bucking on a slope, always stand on the uphill side
of the log. To maintain complete control of the chain saw
when cutting through the log, release the cutting pressure
near the end of the cut without relaxing your grip on the
chainsawhandles.Donotletthechaincontacttheground.
After completing the cut, wait for the saw chain to stop
before you move the chain saw. Always stop the motor
before moving from tree to tree.
Fig. 18
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
BUCKING LOGS UNDER STRESS
LOG SUPPORTED AT ONE END:
LOAD
See Figures 19 - 20.
When the log is supported along its entire length, it should
be cut from the top or overbucking.
FINISHING CUT
When the log is supported on one end, cut 1/3 the diameter
from the underside or underbucking. Then make the finishing
cut by overbucking to meet the first cut.
As the log is being cut, it will tend to bend. The saw can
become pinched or hung in the log if you make the first cut
deeper than 1/3 of the diameter of the log.
1ST CUT
1/3 DIA
Give special attention to logs under stress to prevent the
bar and chain from pinching.
When bucking on a slope, always stand on the uphill side
of the log as shown in Figure 18. When “cutting through,”
to maintain complete control of the chain saw, release the
cutting pressure near the end of the cut without relaxing your
grip on the chain saw handles. Do not let the chain contact
the ground. After completing the cut, wait for the saw chain
to stop before you move the chain saw. Always stop the
motor before moving from tree to tree. See Figure 18.
LOG SUPPORTED AT BOTH ENDS:
LOAD
1ST CUT 1/3 DIA
TYPES OF CUTTING USED
See Figure 20.
OVERBUCKING
Begin on the top side of the log with the bottom of the saw
against the log; exert light pressure downward. Note that
the saw will tend to pull away from you.
FINISHING CUT
OVERBUCKING
Fig. 19
UNDERBUCKING
Begin on the under side of the log with the top of the saw
against the log; exert light pressure upward. During under-
bucking, the saw will tend to push back at you. Be pre-
pared for this reaction and hold the saw firmly to maintain
control.
WARNING:
Never climb into a tree to limb or prune. Do not stand on
ladders, platforms, a log, or in any position which can
cause you to lose your balance or control of the saw.
UNDERBUCKING
Fig. 20
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LIMBING
See Figure 21.
3
2
Limbing is removing branches from a fallen tree.
1
n Work slowly, keeping both hands on the chain saw with
a firm grip. Always make sure your footing is secure and
your weight is distributed evenly on both feet.
n Leave the larger support limbs under the tree to keep the
tree off the ground while cutting.
4
n Limbs should be cut one at a time. Remove the cut limbs
from the work area often to help keep the work area clean
and safe.
CUT LIMBS ONE AT A TIME AND LEAVE SUPPORT LIMBS
UNDER TREE UNTIL LOG IS CUT
Fig. 21
n Branches under tension should be cut from the bottom
up to avoid binding the chain saw.
SECOND CUT
nKeep the tree between you and the chain saw while limb-
ing. Cut from the side of the tree opposite the branch you
are cutting.
LOAD
PRUNING
See Figure 22.
Pruning is trimming limbs from a live tree.
nWork slowly, keeping both hands on the chain saw with
a firm grip. Always make sure your footing is secure and
your weight is distributed evenly on both feet.
FIRST CUT
1/3 DIAMETER
nDo not cut from a ladder, this is extremely dangerous.
Leave this operation for professionals.
FINISHING CUT
nDo not cut above chest height as a saw held higher is
Fig. 22
difficult to control against kickback.
nWhenpruningtreesitisimportantnottomakethefinishing
cut next to the main limb or trunk until you have cut off
the limb further out to reduce the weight. This prevents
stripping the bark from the main member.
SPRINGPOLE
nUnderbuck the branch 1/3 through for your first cut.
nYour second cut should overbuck to drop the branch
off.
nNow make your finishing cut smoothly and neatly against
the main member so the bark will grow back to seal the
wound.
Fig. 23
WARNING:
WARNING:
If the limbs to be pruned are above chest height, hire a
professional to perform the pruning.
Springpolesaredangerousandcouldstriketheoperator,
causingtheoperatortolosecontrolofthechainsaw.This
could result in severe or fatal injury to the operator.
SPRINGPOLES
See Figure 23.
A springpole is any log, branch, rooted stump, or sapling
which is bent under tension by other wood so that it springs
back if the wood holding it is cut or removed. On a fallen
tree, a rooted stump has a high potential of springing back
to the upright position during the bucking cut to separate
the log from the stump. Watch out for springpoles, they
are dangerous.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WARNING:
GUIDE BAR
NUT
Before performing any adjustment, make sure the tool is
unplugged from the power supply. Failure to heed this
warning could result in serious personal injury.
CHAIN
TENSIONING
KNOB
ADJUSTING CHAIN TENSION
See Figures 24 - 26.
TO
LOOSEN (-)
n Unplug the chain saw and remove power cord.
n Loosen the guide bar nut to finger tight, turn the chain
tensioner knob “+” will tension the chain. Refer to “Re-
placing Bar and Chain” later in this manual for additional
information.
TO
TIGHTEN (+)
Fig. 24
A cold chain is correctly tensioned when there is no slack
on the underside of the guide bar, the chain is snug, but
it can be turned by hand without binding.
n Chain must be re-tensioned whenever the flats on the
drive links hang out of the bar groove.
n During normal saw operation, the temperature of the
chainwillincrease.Thedrivelinksofacorrectlytensioned
warm chain will hang approximately .050 in. out of the
bar groove.
NOTE: New chain tends to stretch, check chain tension
frequently and tension as required.
APPROX. .050 (1.25 mm)
FLATS
Fig. 25
Fig. 26
n Retighten the guide bar nut.
CAUTION:
Chain tensioned while warm, may be too tight upon
cooling. Check the “cold tension” before next use.
MAINTENANCE
WARNING:
WARNING:
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
WARNING:
Electrictoolsusedonfiberglassmaterial,wallboard,spackling
compounds, or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips and
grindings are highly abrasive to bearings, brushes, commu-
tators,etc.Consequently,wedonotrecommendedusingthis
toolforextendedworkonthesetypesofmaterials. However,
if you do work with any of these materials, it is extremely
important to clean the tool using compressed air.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING BAR AND CHAIN
See Figures 27 - 31.
SPROCKET
BAR
WARNING:
Before performing any maintenance, make sure the tool
is unplugged from the power supply. Failure to heed this
warning could result in serious personal injury.
SLEEVE
CAUTION:
Always wear gloves when handling the bar and chain;
these components are sharp and may contain burrs.
CHAIN
WARNING:
CHAIN TENSION
PIN HOLE
GUIDE
Nevertouchoradjustthechainwhilethemotorisrunning.
The saw chain is very sharp; always wear protective
gloves when performing maintenance to the chain to
avoid possible serious lacerations.
BAR NUT
CHAIN
COVER
ASSEMBLY
Fig. 27
n Unplug the chain saw and remove power cord.
n Using the scrench, loosen the guide bar nut completely
and remove chain cover assembly (take care not to lose
sleeve).
n Remove the bar and chain from the mounting surface.
n Remove the old chain from the bar.
n Lay out the new saw chain in a loop and straighten any
kinks. The cutters should face in the direction of chain
rotation. If they face the opposite direction, turn the loop
over.
n Place the chain drive links into the bar groove.
NOTE: Make certain of direction of chain.
CHAIN DRIVE
LINKS
n Position the chain so there is a loop at the back of the
bar. Hold the chain in position on the bar and place the
loop around the sprocket of the chain saw. Fit the bar
flush against the mounting surface so that the bar stud
is in the long slot of the bar.
BAR
GROOVE
Fig. 28
TO
LOOSEN
TO
TIGHTEN
RECOMMENDED BAR AND CHAIN COMBINATIONS
Bar Part Number - 18 in.
301304001
Chain Part Number
301139003
SCRENCH ON BAR
GUIDE BAR NUT
CHAIN
TENSIONING
KNOB
Fig. 29
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
nReinstall the chain cover assembly, bushing and guide
bar nut. Tighten the guide bar nut finger tight only. The
bar must be free to move for tension adjustment.
LIFT THE TIP OF
THE GUIDE BAR
UP TO CHECK FOR
SAG
NOTE: When replacing the chain cover assembly assure
that the adjusting pin is in the chain tension pin hole and
that the chain cover assembly fits flush to the housing.
NOTE: Chain tensioning knob has two markings: “+”
tightens the tension of chain and “-” loosens the ten-
sion.
nRemove all the slack from the chain by turning the chain
tensioning knob “+” until the chain seats snugly against
the bar with the drive links in the bar groove.
Fig. 30
nLift the tip of the guide bar up to check for sag. Release
the tip of the guide bar and turn the chain tensioning
knob 1/2 turn “+”. Repeat this process until sag does not
exist.
nHold the tip of the guide bar up and tighten the guide bar
nut securely.
nChain is correctly tensioned when there is no sag on the
underside of the guide bar, the chain is snug, but it can
be turned by hand without binding.
NOTE: If chain is too tight, it will not rotate. Loosen the
guide bar nut slightly and turn chain tension knob 1/4 turn
“-”. Lift the tip of the guide bar up and retighten guide
bar nut securely. Assure that the chain will rotate without
binding.
SCRENCH
Fig. 31
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHAIN MAINTENANCE
See Figures 32 - 33.
CUTTING
CORNER
TOP PLATE
WARNING:
SIDE PLATE
Before performing any adjustment, make sure the tool is
unplugged from the power supply. Failure to heed this
warning could result in serious personal injury.
DEPTH GAUGE
RIVET HOLE
HEEL
Use only 3/8 in. pitch skip tooth/low-kickback
(62 drivelink) chain on this saw. This fast-cutting chain will
provide kickback reduction when properly maintained.
TOE
GULLET
Fig. 32
For smooth and fast cutting, chain needs to be maintained
properly. The chain requires sharpening when the wood chips
are small and powdery, the chain must be forced through the
wood during cutting, or the chain cuts to one side. During
maintenance of your chain, consider the following:
CHECK FOR WEAR
OR DAMAGE
n Improper filing angle of the side plate can increase the
risk of a severe kickback.
n Raker (depth gauge) clearance.
n Too low increases the potential for kickback.
n Not low enough decreases cutting ability.
n If cutter teeth have hit hard objects such as nails and
stones, or have been abraded by mud or sand on the
wood, have service dealer sharpen chain.
Fig. 33
NOTE: Inspect the drive sprocket for wear or damage when
replacing the chain. If signs of wear or damage are present
in the areas indicated, have the drive sprocket replaced by
a Ryobi Service dealer.
HOW TO SHARPEN THE CUTTERS
See Figures 34 - 35.
Be careful to file all cutters to the specified angles and to
the same length, as fast cutting can be obtained only when
all cutters are uniform.
WARNING:
Fig. 34
Improper chain sharpening increases the potential of
kickback.
LEFT HAND
CUTTERS
n Wear gloves for protection. Properly tension the chain
prior to sharpening. Refer to “Adjusting Chain Tension”
earlier in this manual. Do all of your filing at the mid-point
of the bar.
n Use a 5/32 in. diameter round file and holder.
n Keep the file level with the top plate of the tooth. Do not
let the file dip or rock.
n Using light but firm pressure, stroke towards the front
corner of the tooth.
n Lift file away from the steel on each return stroke.
RIGHT HAND
CUTTERS
Fig. 35
n Put a few firm strokes on every tooth. File all left hand
cutters in one direction. Then move to the other side and
file the right hand cutters in the opposite direction. Oc-
casionally remove filings from the file with a wire brush.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING:
CORRECT TOP PLATE INCORRECT TOP PLATE FILING
FILING ANGLE
ANGLE
Failure to replace or repair damaged chain can cause
serious injury.
LESS
THAN 30°
MORE
THAN 30°
30°
WARNING:
Thesawchainisverysharp,alwayswearprotectivegloves
when performing maintenance to the chain failure to do
so may result in serious personal injury.
Fig. 36
CORRECT SIDE
PLATE FILING
ANGLE
INCORRECT SIDE PLATE
FILING ANGLE
TOP PLATE FILING ANGLE
See Figure 36.
n CORRECT30°-Fileholdersaremarkedwithguidemarks
to align file properly to produce correct top plate angle.
HOOK
BACKWARD
SLOPE
n LESS THAN 30° - For Cross Cutting.
80°
n MORE THAN 30° - Feathered Edge Dulls Quickly.
SIDE PLATE ANGLE
See Figure 37.
n CORRECT - 80o Produced automatically if correct diam-
eter file is used in file holder.
Fig. 37
n HOOK - “Grabs” and dulls quickly. Increases potential
RAKER CLEARANCE
.025 in. (0.6 mm)
of KICKBACK.
Results from using a file with diameter too small, or file
held too low.
n BACKWARD SLOPE - Needs too much feed pressure,
causes excessive wear to bar and chain.
Results from using a file with diameter too large, or file
held too high.
Fig. 38
DEPTH GAUGE CLEARANCE
See Figure 38.
nThe depth gauge should be maintained at a clearance of
.025 in. Use a depth gauge tool for checking the depth
gauge clearances.
nEvery time the chain is filed, check the depth gauge clear-
ance.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
NOTE: The locking tab fits in the recessed hole in the
Use a Flat File and a Depth Gauge Jointer to lower all gauges
bar.
uniformly. Depth gauge jointers are available in .020 in. to .035
in.Usea.025in.depthgaugejointer.Afterloweringeachdepth
gauge, restore original shape by rounding the front. Be careful
not to damage adjoining drive links with the edge of the file.
See Figures 39 - 40.
n Tighten the screw with your finger.
n From the finger-tight position, tighten the screw an ad-
ditional 3/4 of a turn using a wrench.
Depth gauges must be adjusted with the flat file in the same
direction the adjoining cutter was filed with the round file.
Use care not to contact cutter face with flat file when ad-
justing depth gauges.
DEPTH GAUGE JOINTER
GUIDE BAR MAINTENANCE
See Figure 41.
When the guide bar shows signs of wear, reverse it on the
saw to distribute the wear for maximum bar life. The bar
should be cleaned every day of use and checked for wear
and damage.
Feathering or burring of the bar rails is a normal process
of bar wear. Such faults should be smoothed with a file as
soon as they occur.
FLAT FILE
Fig. 39
A bar with any of the following faults should be replaced.
n Wear inside the bar rails which permits the chain to lay
over sideways.
RESTORE ORIGINAL
SHAPE BY ROUNDING
THE FRONT
n Bent guide bar.
n Cracked or broken rails.
n Spread rails.
In addition, guide bars with a sprocket at their tip must be
lubricated weekly with a grease syringe to extend the guide
bar life. Using a grease syringe, lubricate weekly in the lu-
bricating hole.
Fig. 40
Turn the guide bar and check that the lubrication holes and
chain groove are free from impurities.
REVERSING THE GUIDE BAR
See Figures 41 - 43.
n Remove the SAFE-T-TIP® mounting screw.
n Remove the SAFE-T-TIP® from the bar.
LUBRICATING HOLE
n Remove the chain from the bar and turn the bar over.
NOTE: Bottom of bar should not be on top.
Fig. 41
n Replace the chain on the bar. Refer to “Replacing Bar and
Chain” earlier in this manual for specific information.
n Replace the SAFE-T-TIP® on the bar nose.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MOUNTING SCREW
LOCKING RIVET
WARNING:
Although the guide bar comes with a SAFE-T-TIP® anti-
kickback device already installed, you need to check the
tightness of the mounting screw before each use.
SAFE-T-TIP® NOSE GUARD MAINTENANCE
See Figures 42 - 43.
Tighten the mounting screw of the nose guard as instructed
below. These are specially hardened screws. If the screw
cannot be installed tightly, replace both the screw and the
SAFE-T-TIP® before further operation. Do not replace with
an ordinary screw.
In addition to preventing chain contact with solid objects at
the nose of the bar, the SAFE-T-TIP® also helps keep the
chain away from abrasive surfaces such as the ground. Keep
it on the right hand side of the bar, where it will be between
the chain and the ground during flush with ground cutting.
SAFE-T-TIP®
Fig. 42
The mounting screw requires a 5/16 in. wrench (or adjustable
wrench) to achieve the recommended tightness of 35 to 45
in. lb. A tightness within this range can be achieved by the
following method.
TIGHTEN 3/4
OF A TURN
n Tighten the screw with your finger.
n From the finger-tight position, tighten the screw an ad-
ditional 3/4 of a turn using a wrench.
MOUNTING SAFE-T-TIP® NOSE GUARD
See Figures 42 - 43.
n Mount the SAFE-T-TIP® on the bar nose.
NOTE: The tab fits in the recessed hole in the bar.
n Tighten the screw with your finger.
Fig. 43
n From the finger-tight position, tighten the screw an ad-
ditional 3/4 of a turn using a wrench.
BAR
TRANSPORTING AND STORING
See Figure 44.
n Do not store or transport the chain saw when it is running.
The chain saw should always be idle before storing or
transporting.
SCABBARD
n Alwaysplacetheguidebarscabbardonthebarandchain
before storing or transporting the chain saw. Use caution
to avoid the sharp teeth of the chain.
CHAIN
n Clean the chain saw thoroughly before storing. Store the
chain saw indoors, in a dry place that is locked and/or
inaccessible to children.
Fig. 44
n Keep away from corrosive agents such as garden chem-
icals and de-icing salts.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
1. Tension chain. Refer to “Adjusting
Chain Tension” earlier in this manual.
2. Check oil tank.
1. Check chain tension for
over tight condition
2. Chain oil tank empty.
Bar and chain running hot
and smoking.
1. Retension chain, Refer to “Adjusting
Chain Tension” earlier in this manual.
2. Refer to “Replacing Bar and Chain”
earlier in this manual.
3. Inspect guide bar and chain for
damage.
1. Chain tension too tight.
2. Check guide bar and chain
assembly.
3. Check guide bar and chain
for damage.
Motor runs, but chain is
not rotating.
1. Dull Chain.
2. Chain on backwards.
Motor runs, chain rotates
but does not cut.
1. Sharpen Chain.
2. Reverse direction of chain.
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.
PARTS LIST
3
2
9
1
7
4
8
6
5
Key
No.
Part
Number
Description
Qty.
1
2
3
4
5
6
7
8
9
301139003
301304001
512197001
308006004
301053001
671307001
671306001
631055002
660640001
983000640
BAR 18in.........................................................................................................................1
CHAIN (Chain figure is for illustration puposes only) .....................................................1
OIL RESERVOIR CAP.....................................................................................................1
SAFE-T-TIP® ...................................................................................................................1
CHAIN COVER ASSEMBLY............................................................................................1
GUIDE BAR SLEEVE BUSHING.....................................................................................1
GUIDE BAR NUT ............................................................................................................1
SCRENCH ......................................................................................................................1
SAFE-T-TIP® (screw and washer)....................................................................................1
OPERATOR’S MANUAL (960986002)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
18 in. ELECTRIC CHAIN SAW
DOUBLE INSULATED
RY43006
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
RY43006
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
Phone 1-800-860-4050
983000-640
2-05
Download from Www.Somanuals.com. All Manuals Search And Download.
|