Interaction of learned keys and keymover:
Press VID, DVD, TV, or
UNO once to select a
home entertainment-
component to control.
3. Press the battery cover back into
place. The tab should click when the
cover is locked.
4. Aim the remote control at the the
TV and slowly alternate between
pressing PWR and TV. Stop when the
TV turns off.
NOTE: If a code digit is “0”, the LED
will not blink.
PROGRAMMING
TROUBLESHOOTING
TV/VCR COMBO CONTROL
• If both a learned function and a key-
moved function are placed on the
same key, whichever was pro-
PROBLEM: LED does not blink when you press a
key.
5. Repeat step 4 three more times for
remaining digits. Use 2 for the sec-
ond digit, 3 for the third digit, and 4
for the fourth digit.
Perform the following instructions to
control a TV/VCR Combo:
SOLUTION: Replace the batteries with two (2) new
AA alkaline batteries.
4. Test the unit by pressing PWR and
any mode key (e.g., VID, DVD, etc.). If
the batteries are inserted correctly,
the LED will blink once.
UNO-LRC1
grammed last will take precedence.
Use the keypad (0 ~ 9)
to directly select chan-
nels (for example, 09
or 31).
NOTE: In the search mode, the UNO-
LRC1 will send IR codes from its
library to the selected device, starting
with the most popular code first.
PROBLEM: LED blinks when you press a key, but
home entertainment component does not respond.
UNIVERSAL LEARNING & PRE-
PROGRAMMED REMOTE CONTROL
1. Turn on the TV/VCR Combo and
insert a video cassette.
• A learned function cannot be used as
a source for keymover, keymover
always uses the key’s original func-
tion as the source.
SOLUTION: Make sure the UNO-LRC1 is aimed at
your home entertainment component and is not far-
ther than 15 feet away.
6. To check for the codes of your other
components, repeat steps 1 through
5, but substitute the appropriate key
(i.e., VID, DVD, or TV) component you
are checking.As before, write down
each four-digit code.
NOTE: When batteries need replacement,
the UNO-LRC1 will blink twice with every
key press. Simply replace them and the
remote control will be restored to its full
functionality, including favorite settings.
NOTE: Please read steps 2-4 completely
before proceeding. We recommend
highlighting or writing down the code
for the brand you wish to program
before moving onto step 2.
PROBLEM: UNO-LRC1 does not control home enter-
tainment components or commands are not working
properly.
Press MUTE once to turn sound
5. Press SETUP once to lock in the code.
off or on.
Limitations on Learning
6. To search for the codes of your other
components, repeat steps 1 through
5, but substitute the appropriate key
(i.e., VID, DVD, or TV).
SOLUTION: Tr y all listed codes for the component
brands being set up. Make sure they can be operated
with an infrared remote control.
Press ENTER once after entering
channel numbers on some TV
models.
• There are certain device codes which
are not learnable. These include
multi-frequency codes (e.g.
Te l e f u n ken), some high frequency
codes, and other unusual formats.
2. On the UNO-LRC1, press DVD Press
and hold SETUP until the LED blinks
twice, then release SETUP.
PROBLEM: TV/VCR combo does not respond prop-
erly.
PROGRAMMING
COMPONENT CONTROL
The UNO-LRC1 can control up to eight
different components. Perform the fol-
lowing instructions for each component
you want controlled:
CHANGING VOLUME LOCK
The UNO-LRC1 is set to control volume
of a component through your TV while
Use VOL + (or VOL -) to raise (or
lower) the sound volume.
SOLUTION: Use the VCR codes for your brand.
Some combo units may require both a TV code and
a VCR code for full operation.
LEARNING CAPABILITY
3. Use the Setup Codes For TV/VCR
Combos (on the back side) to locate
the brand name and then enter the
first four-digit code for your compo-
nent. If performed correctly, the LED
will blink twice.
• The learner will support IR codes
with carrier frequency up to 135
Khz.
PROBLEM: No volume on a 2nd TV.
To op t i mize success, the learning process
should be conducted in an area where
there is a low level of IR emission. High
levels of “natural light” or energy effi-
cient fluorescent lights could interfere
with a learning event The source and
target (learner) remotes should be no
more than 1 to 2 inches apart during a
learning event and the IR LEDs of the
two units should be aligned with each
other. The learning operation is initiated
as follows:
in the
,
, or mode. In UNO
Use CH + (or CH -) to select the
next higher (or lower) channel.
SOLUTION: Follow instructions in Changing
Volume Lo ck .
mode, you have control of your UNO
keypad’s volume.
PROBLEM: CH+ , CH , and LAST do not work for
-
• The unit can learn only one code per
key. It can’t be taught a sequence of
several keystrokes on one key.
your RCA TV.
If your TV is not remote controllable, or
if you want volume to be controlled by a
different component, you can change the
Vo lu m e L o c k s e t t i n g to control a volume
through a non-associated mode (e.g.,
through the cable in the TV mode).
NOTE: For TV/VCR Combo control, see the
next section.
Press LAST once to recall the last
channel and to page back one
screen in the main menu.
SOLUTION: Due to RCA design (1983-1987), only
the original remote control will operate these func-
tions.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
1. Turn on a component (e.g.,VCR)
and, if applicable, insert media,
(e.g., cassette or disc).
• All keys with the exception of Modes,
and SETUP can be learned on.
PROBLEM: Changing channels does not work
properly.
Press SLEEP to activate your TV’s
sleep timer. Or if none is avail-
able, press SLEEP to activate the
UNO-LRC1’s sleep timer for
automatic shut-off of your TV.
Each key press (up to four) add
15 minutes to the sleep timer.
SOLUTION: If original remote controlrequired
pressing ENTER to change channels, press ENTER on
the UNO-LRC1 after entering the channel number.
4. Aim the UNO-LRC1 at the compo-
nent and press PWR once. It should
turn off. If it does not respond, repeat
steps 2-3, trying each code for your
brand until you find one that works.
If it still does not work, try searching
for the code (see Searching For Your
Code).
• During a learning event. The source
remote and target should be no more
than 1 to 2 inches apart.
NOTE: Please read steps 2-4 completely
before proceeding. We recommend
highlighting or writing down the codes
and device you wish to program before
moving onto step 2.
To change Volume Lock to another
mode:
PROBLEM: Tried “Search Method” and still could
not find a working code.
1. Press and hold SETUP until double
blink confirmation. Press 9 - 7 - 5 to
initiate learning mode.
SOLUTION: Tr y the “Search Method”again after
clearing out the device key as follows: Press and hold
SETUP until red light blinks twice, then release. Next
enter 9 - 9 - 2. Then press and release the device key
to be cleared twice.
• In some cases you may be required
to re-learn a code if it is not correctly
learned.
1. On the UNO-LRC1, press and hold
SETUP until the LED blinks twice,
then release SETUP.
USER GUIDE
Press INPUT once to
switch the input of the
chosen component.
2. On the UNO-LRC1, press a compo-
nent key once (i.e., VID, DVD or TV).
Press and hold SETUP until the LED
blinks twice, then release SETUP.
2. Press [MODE] and key to be learned
(time out if no key pressed in 10 sec-
onds).
• The learning process should con-
ducted in an area where there is a
low levels of IR emission. High levels
of “nature light” or Energy efficient
fluorescent lights, could interfere
with a learning event.
PROBLEM: Remote control does not turn on Sony
or Sharp TV/VCR Combo.
2. Enter 9 - 9 - 3 and then press any
mode key once (except TV). The LED
will blink twice.
INTRODUCTION
NOTE: If the device does not have a PWR
key, press PLAY.
SOLUTION: For power on, these prod-ucts require
programming TV codes. For Sony, use TV code
0000 and VCR code 0032. For Sharp, use TV code
0093 and VCR code 0048.
Use GUIDE to displaythe program
The UNO-LRC1 from Russound is the
complete solution for all of your remote
control requirements. It is designed to
operate source devices and the audio
system keypad.
3. Visible LED flashes rapidly (time out
if no received signal detected in 4
sec.)
guide.
5. If you’ve located a setup code that
works, but it has a separate TV code,
you’ll also need to program it into the
UNO-LRC1 to access volume control
as follows:
Components are assigned
to each component key.
3. Now, whenever you press VOL +,
VOL –, or MUTE, volume will be con-
trolled by your mode choice.
Use EXIT to exit out of the select-
ed component’s menu or guide.
=Cable, Satellite, DSS,Vid Acc.
=VCR, DVD, LDP,Audio Cassette,
DVR
=VCR, DVD, LDP,Audio Cassette,
DVR
• In general, it is not recommended to
learn a function to the Record Key.
The Record Key requires a double
key press to send the record function
in normal operation. The double key
press is lost when the Record key is
involved in most learning operations.
This lack of consistency in operation
generates a source of confusion for
the user and is best to be avoided
when possible. However, the Record
key is learnable.
4. Hold teaching remote close to IR
LED and press key to be taught.
To change Volume Lock back to the
TV mode:
The UNO-LRC1 is also customizable to
allow for key configurations that meet
your specific needs. It’s also packed with
these features for you to choose from:
Use the cursor keys to
move the cursor in the
program guide and
menu screens.
a. Press TV once. The LED will
5. Visible LED goes out. Continue to
press teaching key until double blink
from visible LED. (One long blink
indicates a learning failure)
blink twice.
1. On the UNO-LRC1, press and hold
SETUP until the LED blinks twice,
then release SETUP.
=UNO Keypad
b. Enter the TV code for your
TV/VCR Combo. If correct, the
LED will blink twice.
• Preprogrammed technology for
easy setup
3. Use the Manufacturer’s Codes (on the
back side) to locate the the type of
component and brand name and
then enter the first four-digit code
for your component. If performed
correctly, the LED will blink twice.
Use SELECT to choose options
from your selected component’s
menu or guide.
6. Repeat steps 2 through 5 as often as
desired (up to limit of memory).
2. Enter 9 - 9 - 3 and then press TV.
The LED will blink twice.
If there is no separate TV code listed,
you will need to perform the follow-
ing steps to access volume control:
• Controls UNO keypads and source
equipment
7. Exit learning mode by pressing
3. Now, whenever you press VOL +,
VOL –, or MUTE on the UNO-LRC1,
volume will be controlled by your TV.
Use INFO to display current
channel and program informa-
tion.
SETUP, or by time out (10 seconds).
• Inclusive audio/video library
a. Press and hold SETUP until the
LED blinks twice, then release
SETUP.
At step 5, one long blink indicates learning fail-
ure, which could be:
• Typically, there are up to 24 buttons
that can be learned.
• Dedicated operation of audio system
keypad
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
Press MENU to access the menu
of your chosen component.
a. Bad capture (try again)
b. Memory full (delete some other
function)
c. Unlearnable code
Deleting a learned code:
This manual provides a basic overview
on how to set up and operate the UNO-
LRC1. Please read the following instruc-
tions to see how easy setup is.
b. Enter 9 - 9 - 3 . The LED will
4. Aim the UNO-LRC1 at the compo-
nent and press PWR once. It should
turn off. If it does not respond, repeat
steps 2-3, trying each code for your
brand until you find one that works.
If it still does not work, try searching
for the code (see Searching For Your
Code).
CHECKING THE CODES
Use the transport keys
to control your VCR, or
CD or DVD player.
blink twice.
If you have set up the UNO-LRC1 using
the Searching For Your Code procedure,
you may need to find out which four-
digit code is operating your equipment:
c. Press DVD once. The LED will
blink twice.
Use these keys to con-
trol the UNO-Series
Keypads
To de l e te a l e arned code, either overwrite
it with a new code on the same key, or
use the following sequence:
FEATURES AND FUNCTIONS
Use the Key Charts to learn how the
UNO-LRC1 functions.
SEARCHING FOR YOUR CODE
For example, to find out which code is
operating your TV:
If your device does not respond to the
UNO-LRC1 after trying all codes listed
for your brand, or if your brand is not
listed at all, try searching for your code.
For example, to search for a code for
your TV:
Press [MODE] then SETUP (press and
hold till you see two blinks) 9 - 7 - 6
then press the key you wish to delete
twice.
NOTE: If the device does not have a PWR
key, press PLAY.
INSTALLING BATTERIES
1. On the back of the UNO-LRC1, push
the tab and lift off the battery cover.
1. On the UNO-LRC1, press TV once.
Key Charts
2. Press and hold SETUP until the LED
The LED (red light) blinks to
show that the remote control is
working and is sending signals.
5. Repeat steps 1 through 4 for each
component you want the UNO-LRC1
to control.
blinks twice, then release SETUP.
Sending a key’s original (preprogrammed)
function:
3. Enter 9 - 9 - 0. The LED will
2. Obtain two (2) fully-charged AA
alkaline batteries. Match the + and –
marks on the batteries to the + and
– marks in the battery case, then
insert the new batteries.
blink twice.
1. On the UNO-LRC1, press TV once.
Use SETUP for all programming
sequences.
If a function is learned onto a key, then
SETUP - key will send the key’s original
function (as long as nothing else has
been learned or keymoved onto the
“shifted” key as well).
4. To view the code for the first digit,
press 1 once. Wait 3 seconds, count
the LED blinks (e.g., 3 blinks = 3)
and write down the number.
2. Press and hold SETUP until the LED
blinks twice, then release SETUP.
Press PWR once to turn on or off
the selected home entertainment
component.
3. Enter 9 - 9 - 1. The LED will
blink twice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|